Search Documents

By Olav Idelgeland

FROM indirect evidence point defects have been believed to influence the fatigue behavior of metals and alloys.1,2 Measurements of changes in resistivity made after cyclicstressing at low temperatures indicate that a very high density of defects is present, part of which may be removed by room-temperature annealing.3'4 These results are consistent with the generation of a high number of point defects at low temperatures. Corresponding measurements made after room-temperature stressing did not show any recovery effects.3 This was attributed to a stabilization of the dislocation network after a few thousand cycles without generation of vacancies. In this laboratory resistance measurements of copper single crystals, shaped as normal fatigue specimens ,5 have been made with a Kelvin double bridge at room temperature during and after cyclic stressing at 80 cps by comparing with a dummy at a close and constant temperature. Temperature differences were measured to ±0.025°C with fine thermocouples taped onto the gage lengths. Potential leads were tin-soldered into small holes in the gage length to give stable values. Corrections for differences in temperature and changes in mean length of the specimen were made according to the formula:

Jan 1, 1968

By G. Reinberg, C. D. Clarke

MOST underground mining operations are dependent on pumping installations to keep the mine unwatered. The reliability of such installations is obviously of paramount importance. The volume of water to be handled is often considerable, and the total head is relatively high. In these cases, both capital cost and operating expense of the pumping installations will become significant factors in overall mining costs. To insure reliability and to keep efficiencies, and hence operating cosl;s, within acceptable limits it goes without saying that mechanical maintenance of a mine pumping installation must receive scrupulous attention at all times. Large mine pumping installations today almost invariably use multistage centrifugal pumps, since positive-displacement units would not be economically competitive except under very unusual conditions of small volume combined with extremely high heads. Centrifugal pump maintenance, under ideal circumstances, would be confined to parts subject to normal running water, i.e., bearing surfaces, stuffing box packing, and shaft sleeves. Under adverse conditions, however, metal may be lost from the wetted surfaces of a pump by erosive or corrosive action of the pumped fluid, and maintenance costs can easily attain enormous proportions. The following definitions are those most generally used for the phenomena encountered. Erosion is a general term meaning mechanical removal of material from a surface. As applied to pumps, it may be the result of simple abrasion, such as that produced by suspended solid matter in the liquid being pumped. In common with other hy-

Jan 1, 1957

By R. V. Ramani, R. M. Mishra, Y. J. Wang

The validity of the concept of mine resistance in ventilation systems is examined. Mine resistance is the proportionality constant relating the head generated by a fan and the quantity flowing through it when the fan is connected to a mine circuit. It is the total effect of all branches in the mine ventilation circuit. Its importance lies in the fact that for new mine projections, and in the extensions of existing mines, ventilation calculations are usually based upon adjustments of the mine resistance. In ventilation circuits with regulation, and/or with multi-fans, simple adjustments of the mine resistance curve do not lead to correct solution. A ventilation system consists of several interconnected subsystems where one subsystem behavior affects that of the others, and the total system. Through a series of simple but realistic examples, the authors demonstrate the importance of the systems concept in mine ventilation, and its practical application to coal mine ventilation planning. Starting from an initial system with no leakage and one fan, more complex ventilation networks with several leakages, sections and fans, are analyzed to show that ventilation system design on the basis of total systems approach is the correct procedure.

Jan 1, 1979

By S. F. Kelly, Theodor Zuschlag, Bela Low

Gold has been mined in the state of Georgia for over 100 years, and although the total production is nearly $18,000,000, the output has declined to an insignificant figure in recent times. The increase in price of gold has brought about a revival of interest in this district, with the result that an electrical survey was undertaken in the McDuffie County gold belt to see whether new quartz veins could be discovered. The problem of locating quartz veins electrically has only rarely been attempted by geophysicists, because of technical difficulties. New improvements in apparatus and field procedures, the most recent of which is the designing of the Ground Comparator, now make possible the differentiation of quartz veins and enclosing rock. This instrument is designed to eliminate the effect of ground contact resistances, and measures the ratio of potential drops between successive stations. These are transformed into resistivity ratios, the highly resistant quartz veins manifesting themselves by sharp breaks in the resistivity-ratio curves. Surface variations of resistance are eliminated by a special technique. Electrical surveys were made on two properties about 40 miles west of Augusta, Georgia. A reconnaissance of the Woodall and detail work on the Hamilton required about. 13,000 ft. of electrical profile. Typical profiles from each are given, with the results of trenching certain of the electrical indications. Comparisons are made between the reactions due to veins several feet wide and those from small quartz stringers. Instances are cited where the electrical profiles were used to trace extensions of known veins, or to establish their nonextension. The discovery of several veins is described, most of which were barren, but of which at least two showed gold in encouraging amounts. The field of application of the Comparator to the prospecting for metallic and nonmetallic minerals, and to the study of various geological problems, is discussed at the close of the paper.

Jan 1, 1934

By Orr Hamilton

VALUATION of a mine is an approximation of its true cash value which requires the application of fundamental principles of economics. Mines are valued from necessity, for the following reasons: (a) Transfers of titles. (b) Dissolutions of partnerships or corporations. (c) Mergers of mining companies. (d) Appraisals for the purpose of State and Federal taxation. (e) Establishment of the fact of worth as a basis of loans. (f) Determination of values as frequently required in litigation. (g) Listing of stock for sale by a reputable stock exchange. For the majority of purposes a valuation is required as at the present time, but for some purposes valuations as of bygone times may more nearly reflect the intrinsic worth of a mine because its subsequent history can never be, entirely ignored, but valuations made as at the present time are better indicators of cash values. Many mines with great intrinsic worth have been sold for small cash prices. The object of legitimate mine valuations is to deter-mine salable value, or that price in cash at which a transfer of the property from a willing seller to a willing buyer might be consummated, assuming that both vendor and vendee have knowledge of all pertinent data and that the owner, is not forced to sell at a sacri-fice-the definitions of fair market value precluding a forced sale.

Jan 11, 1923

By Ronald A. Murdock

INTRODUCTION Exxon's Highland Uranium Operations in eastern Wyoming consists of an open pit, an underground mine and a mill complex. The geology of the deposit is reviewed in this paper, and an overview of the mining operations at both the surface and underground mines is presented. Topics discussed include geology, stripping of overburden and mining of ore in the open pit, and underground development and stoping methods. GEOLOGY The Highland uranium deposit was discovered in 1968 by Exxon Minerals Company, U.S.A., in Converse County, Wyoming, 35 miles north of Douglas. The mine is located at an elevation of about 5,200 ft in a high-plains, sagebrush-covered prairie typical of eastern Wyoming. The deposit is near the southern edge of the Powder River Basin in the Paleocene Fort Union Formation. The Fort Union Formation consists of 1,900 to 3,200 ft of sandstone, siltstone, mudstone, claystone and coal beds. Siltstone, mudstone and claystone are collectively referred to as "shale" at Highland. There are many alternating layers of shale and sandstone in the Fort Union Formation; but in the Highland area, there are only three principal sandstones, known as the Highland Sand Group, which host the uranium. The combined sand thickness is about 150 ft.

Jan 1, 1983

By John M. Dale

Sulfur has attractive features as a base material for coating systems. It melts at 246ºF and can be applied as a liquid above this temperature. Its melting point is just above the environmental stress level, 180°F, for most coatings and yet it is low enough to be easy to work with in comparison to many hot melt systems. The viscosity characteristics are such that sulfur lends itself to spray applications. The oxidation rate of sulfur in the atmosphere is very low and sulfur has outstanding chemical resistance characteristics, particularly in acid environments. One of the greatest potentials for these coatings appears to be in the protection of other materials. At one time, most acid tanks and pits were constructed with acid- proof brick and sulfur based mortars. This type of construction is much more expensive than sulfur based spray coatings. An attractive sulfur based coating composed of sulfur, talc, milled glass fibers and dicyclopentadiene,1 developed by the Institute for the Bureau of Mines has excellent acid assistance and can be used to protect concrete from acid attack.

Jan 10, 1973

IN my opinion antimony* is a composition made by Nature to create a metallic mineral that is overflowing with an undue proportion of hot and dry material and with its moisture poorly mixed, with an effect wholly contrary to the composition of metals. Therefore, it comes to be, like quicksilver, a mineral deformity and monstrosity among metals. Or it might be a material that is about to reach metallic perfection, but is hindered from doing so by being mined too soon. I am persuaded to this opinion by seeing in it so many parts similar to those of metals, considering first its clear and brilliant color and its great weight and then the regulus† that it leaves at the bottom of the vessel on melting. Obviously it has in it much earthiness, as is attested by the odor of its sulphurous burning, its imperfect blending, its defective mixture, its difficult fusion, and finally the character of its regulus, for although this is very white and almost more shining than silver, it is much more brittle than glass. [28] The practical philosophers make great use of it in their alchemistic work in order, they say, to make an oil that they believe gives the color of gold to fixed silver. For this reason many of them hold it in high repute, especially the kind that has long thin fibers like a bundle of bristles. And they say that they can obtain greater results with it than with sulphur. I believe this, however, in case it is aided by sulphur, since it is nearer the metallic species than sulphur is. This I know for a certainty because I have seen them extract from it a bloody liquor in the form of an oil. The alchemist who made that which I saw told me that it had not only the

Jan 1, 1942

By Howard M. Wells

The investment worth of a mineral deposit can only be realistically evaluated in relation to specified engineering design criteria which fully detail the proposed method of exploitation. The operational design of a mine falls essentially within the technical discipline of the mining engineer, under the constraint that the technical design should be aimed at optimizing the financial attractiveness of the project. In the case of a marginally viable proposition it becomes vitally necessary to identify the best set of design parameters which together will add up to an optimum investment proposal. This paper examines some fundamental logic of optimization for a "wasting asset" type of investment such as a mine, with special reference to the rate of annual production and the strategy of selective mining.

Jan 1, 1979

By H. O. Hofman

THE leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which; according to Pelabon,1 is 550°C., according to Wagemann2 540°C., and according to Borgström3 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343°, if 0.1 to 0.2 mm.; and 430° if 0.2 mm. 3. The fusibility of a mixture of Sb2S3 and Sb203 which in the form of kermesite (Sb2S3)2.Sb203 melts at 517°C.5 4. The volatility of Sb2S3 and Sb203, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures.

Jan 1, 1916

By P. Somasundaran, Y. H. C. Wang

A detailed study of carrier flotation of kaolin clay using calcite showed the major beneficiation mechanism to be enhanced aggregation between anatase and calcite under intense agitation conditions. To develop an understanding of this selective aggregation, surface charge characteristics of kaolinite, anatase, and calcite were studied under simulated flotation conditions. Zeta potential of all these minerals tended towards a constant negative value in oleate solutions under certain conditions possibly due to adsorption or precipitation of oleate on them. However, whereas the zeta potential of anatase in the oleate solutions was not influenced by the agitation level, that of kaolinite was found to be strongly dependent on the agitation intensity. The effect of oleate on zeta potential of kaolinite was reduced by an increase in agitation intensity. It is suggested that oleate is much more firmly bound to the surface of the anatase and that this preferential attachment is responsible for the enhanced selective aggregation of the anatase with calcite. Agitation level plays a major role in carrier flotation since intense agitation is considered to enhance both the chemisorption of oleate on anatase and preferential detachment of calcium oleate precipitate from the kaolinite surface, all of this producing a large difference in the surface Properties of anatase and kaolinite, and hence in their tendency to aggregate with calcite.

Jan 1, 1983

By Rossiter W. Raymond

The manufacture of ferromanganese in the blast furnace having been the subject of considerable attention in the Institute, I beg to put on record a contribution to the discussion from a quarter hitherto not directly represented, namely, the St. Louis furnaces, near Marseilles in France, belonging to a company of which M. Jordan, a member of the Institute, is Managing Director. These furnaces commenced in 1862 to manufacture specular pig (fontes facettes) containing from three to six per cent. of manganese. In 1864 the regular production of spiegeleisen (fontes miroitantes), containing seven to ten per cent. of manganese, was inaugurated. At that time the Rhine was the only locality of this manufacture, and the Bessemer works of England and France obtained from Gernlany all their spiegel. From 1864 to the present time, the St. Louis furnaces have been advancing steadily the percentage of manganese in their product. From ferromanganese of thirty per cent. they had arrived, about two years ago, at a product containing seventy to seventy-five per cent., and for some time past they have been turning out what, as M. Jordan remarks, may fairly be Termed fonte de manganese, or manganese pig, instead of iron, since the percentage of iron it contains is not more than 8.5, while the percentage of manganese is 85, or ten times as great. This very high grade material has a peculiar appearance, entirely different from that of ordinary cast iron or spiegel. It is granular, and steely gray in color. The following analyses, communicated to the Sociètè des Ingenieurs Civils, by M. Jordan, show the composition of various products of the St. Louis furnaces:

Jan 1, 1879

By Herbert Everest

THE idea of economical production is usually associated with large operations, tonnages, and mines, with even larger capital behind them. Nevertheless many small mines operate in the shadow of large competitors and make a good showing on the capital invested despite larger overhead expenses. For the purpose of this discussion I will divide the cost of production into classes, and specify opposite each the approximate percentage expended thereon: 1. Labor, including miners and company men; 60 to 75 per cent. 2: Development, including all necessary yardage, room turning, crosscuts, etc.; 7 to 12 per cent. 3. Deadwork, covering payment to miners for handling falls, drawslate, or faults, rock work, water, and in general, all nonproductive labor; 3 to 7 per cent. 4. Supplies: mine timbers, oil, brattice material, lumber, cement, and repairs to equipment; 2 to 6 per cent. 5. Expense: management, selling, office, taxes, etc.; 1 to 5 per cent. 6. Depreciation of coal reserves and royalties; 6 to 10 per cent. 7. Depreciation of equipment and interest on capital invested; 1 to 3 per cent. 8. Fuel; ½ to 1 ½ per cent. The labor cost for a small mine is relatively much lower than for a large mine, particularly the sum paid to company men. Idle-pay expense is cut to a minimum; the labor item being larger than all the others together, a saving in labor makes a decided showing on the total cost. The development charges in small and large mines are about the same. There should be a small showing on the Beadwork item in favor of the small mine. The unit cost for supplies is usually small in the small mine. The operator of the small mine finds, owing to a limited tonnage, that the expenses of management, selling, etc., are abnormally high.

Jan 1, 1916

By George Sears

UNTIL a comparatively few years ago, interest in tantalum was limited almost wholly to its scientific investigation, but its extreme resistance to the action of even the strong mineral acids, its great avidity for the common gases, hydrogen, oxygen and nitrogen, and its capacity for transforming alternating to direct current are winning for it a place in our industrial life. Tantalum is not attacked by any single acid except hydrofluoric, nor is it affected by solutions of alkalies. Aqua regia, which readily dissolves both platinum and gold, has no action on it. This resistance to the common corrosive agents is an outstanding property of tantalum and accounts for many of the applications to which it has been put. When heated, tantalum reacts readily with oxygen and nitrogen and absorbs large volumes of hydrogen, 740 volumes being taken up at a dull red heat. This capacity for absorbing gases is being utilized to an increasing extent in the manufacture of vacuum tubes, in which tantalum is used for the metal parts, especially for grid wire. It is said to be a superior metal for this purpose, particularly in power and sending tubes, because of its low secondary emission. The use of tantalum in the manufacture of electrodes, dishes, spatulas and other laboratory apparatus appears to be fairly steady. There has been some development in its use for dental instruments, surgical tools, pen points, hypodermic needles and acidproof pumps. Recently it has been used in the manufacture of spinnerets for the rayon industry, of nozzles for the manufacture of artificial casings for sausages and of lining for plant equipment.

Jan 1, 1930

By V. Runolinna, R. T. Hukki

Preliminary separation of precious metals by flotation can offer a simplification of the conventional method of treatment of anode slimes. Laboratory flotation experiments show that rich gold and silver concentrate can be obtained with excellent recoveries. THE purpose of this paper is to present the results of an investigation into the possibilities of separating precious metals from anode slimes by selective flotation. The work was carried out at the State Research Institute in Helsinki, Finland. The sample of anode slimes tested was submitted by the Outo-kumpu Co. in Finland. In 1947 the average assay of filtered and dried anode slimes in the Outokumpu refinery in Pori was as follows: Au, 0.50 pct; Ag, 9.38 pct; Cu, 11.02 pct; Ni, 45.21 pct; Pb, 2.62 pct; Fe, 0.60 pct; Sn, 1.00 pct; Sb, 0.04 pct; As, 0.70 pct; Se, 4.33 pct; S, 2.32 pct; SO,, 2.17 pct; SiO2, 2.25 pct. The daily assay naturally varies considerably from the figures presented above. The present conventional method of treatment of anode slimes consists of the steps shown in the flowsheet in fig. 1. As seen from this simplified flowsheet, the present method of treatment involves many steps by which the components of the anode slimes are removed one after another until the main products, gold and silver, may be separated. Due to the small scale of operations, the above procedure is carried out in small batches requiring considerable amount of manual labor. If, however, the anode slimes could be treated in

Jan 1, 1951

By J. E. Dinger, Ross Gunn

Faraday's Law of magnetic induction states that the e.m.f. acting around a closed circuit is equal to the time rate of change of flux through that circuit. If the closed circuit is a conducting medium, there will flow an electric current which is propor¬tional to the conductivity of the material and the time rate of change of the flux. Electrical currents so induced in a con¬ducting material are often referred to as eddy currents. Eddy currents are thus induced into a conducting material by (1) a time rate of change of the magnetic field through the material, by (2) a relative motion of the conducting material and a magnetic field, or by (3) a combination of (1) and (2). Because the magnitude of the induced eddy currents is dependent upon the resistance of the equivalent conducting path, these currents offer a method of detecting electrical discontinuities in a

Jan 1, 1945

By Ashbel Welch

Ashbel Welch, Lambertville, N. J.: Dr. Dudley has given the wear of steel rails under four different conditions. He arrives at the conclusion that the softer rails, or those that from their composition ought to be softer, wear better than the harder. But there is another condition which has an important bearing on the subject, and should not be overlooked,—the weight on a wheel. With the lighter weights of the past, the softer rails may have worn best; with the heavier weights of the future, the harder may wear best. Weights will probably be increased up to the capacity of steel to bear; then doubtless the harder steel will wear best. A leaden rail with ten pounds on a wheel might carry millions of tons, but with one hundred pounds on a wheel, it would be destfoyed by a few thousand tons. So in the days of iron rails, my experience was that the softer rails under light machinery stood better than some of the harder; but under heavy machinery the softer were much the most rapidly destroyed. It is doubtless the same with steel. The pounding motion of the wheels loosens or spreads the particles of a thin film of steel; the pull lengthwise on the rail de-

Jan 1, 1881

By C. M. St. John

INTRODUCTION The stress redistribution accompanying the excavation of a deep tunnel may induce failure of the rock. The role of the support system is to control the extent of the failed region and hence to limit closure of the tunnel within an allowable amount. In such circumstances, the design of the support system is generally based on the Ground Reaction Curve (GRC). The GRC is the relationship between the support pressure and the induced displacement at the tunnel wall for a circular tunnel under hydrostatic loading. In the calculation of the GRC (see Brown et al. (1983) for an exhaustive list of reference), the rock is generally treated as an elastoplastic material characterized by cohesive-frictional yield strength and by dilatancy during plastic deformation. A recent analytical development (Detournay, 1983) has allowed the generalization of the GRC concept for some cases of non-hydrostatic in-situ stress fields (Detournay and Fairhurst, 1982). As an application of that development, this paper describes design charts that provide powerful means of performing parametric analysis for tunnels subject to non-hydrostatic loading. BACKGROUND The in-situ stress in a plane perpendicular to the tunnel axis can be decomposed into mean and deviatoric components, Po and So (see Fig. 1). Since it is assumed that the rock is characterized by a Mohr-Coulomb yield strength, the deviatoric invariant So must be less than the limiting value Sl0 given by

Jan 1, 1984

By Alan K. Burton

Along with tires and transmission systems, engines have been a limiting factor in the growth of large off- highway trucks. The problem, primarily, has been the development of reliable, high-performance engines that are not prohibitively heavy or expensive. For many years, horsepower to overall truck weight ratios have been in the vicinity of 300 lb per hp for rear dump units up to 50 tons capacity. This ratio is obviously very poor when compared to the much lighter and smaller highway trucks, which frequently have a performance ratio of 100 lb per hp. Unfortunately, the larger mining trucks have not been able to match even the 50-ton trucks, and in some cases, ratios have dropped as low as 450 lb per hp. This results in a performance of only 67% of that achieved by the older smaller trucks. Thus, the message is clear: what is needed is more horsepower and less weight.

Jan 10, 1975

By John B. Goddard, David R. Brosnahan

Leaching of uranium in situ from sandstone deposits with ammonium carbonate solution containing dissolved oxygen occurs rapidly compared with the leaching of the bulk of the sulfur present as FeS2. However, because of their high reducing capacity and their relative abundance, the FeS2 minerals consume the bulk of the oxidant. A pressure leach apparatus was constructed that permitted measuring oxygen consumption by FeS2, best described by a first-order reaction. The experimental rate constants for various cores are roughly proportional to their FeS2 contents.

Jan 1, 1983