Search Documents

By L. G. Carpenter, D. E. Garrett

Probably the largest single tungsten deposit in the U. S. is one that has yet to produce any tungsten; it is not even listed in tables showing U. S. reserves. This deposit is at Searles Lake, Calif., where the brine contains about 70 ppm WO,. Small though the concentration is, the amount of brine in the lake is so great that it is estimated at 170 million lb of WO3 (8.5 million units), equaling the total of all other known reserves in the U. S. This dry lake is located in the basin formed by the Argus and Slate ranges in the northeastern corner of the Mojave Desert (Fig. 1). It consists of a massive salt body some 35 sq miles in extent, varying in thickness from 0 to 120 ft and containing more than 3 billion tons of salt. A central section of about 8 sq miles is exposed salt; the remaining area is overlain by mud. Except for the exposed sodium chloride (10 to 15 ft thick) the body consists of a very complex and heterogenous mixture of soluble crystals, containing at least eight major phases. It is only about 53 pct solid, the voids being occupied by a dense brine which is the raw material for two chemical companies operating in the valley. The deposit is believed to be made up of salts present in the runoff waters from the last two ice stages. Searles Lakes was the third in a chain of five lakes that received waters from the Owens Valley drainage of the Sierra Nevada Mts. After leaving Owens Lake the waters could flood in succession into the Indian Wells, Searles, Panamint, and Death valleys (Fig. 2). During the first two ice stages of the Pleistocene Epoch most of the waters eventually arrived at Death Valley; consequently the lower 3300 ft of Searles Valley contain only mud

Jan 1, 1960

By H. P. Reid

Portland cement is manufactured under either of two general processes, the wet or the dry. The raw materials in general consist of limestone, shells, marl, cement rock, clay, shale, blast-furnace slag, etc., so proportioned that when calcined the desired composition will be obtained. In the wet process the combined raw materials are ground to extreme fineness in the presence of water, to a resulting slurry of from 30 to 50 per cent moisture content. The moisture of the slurry may be reduced by thickening or filtering processes for feed to the cement kiln or the slurry may be fed to the kiln with its full percentage of water. The dry process differs from the wet in that the surface moisture of the raw materials is removed prior to grinding. For the drying of these materials heat is required and in most cases is produced by burning of raw fuel either on grates or stokers before the dryers or in suspension in the form of pulverized coal, oil or gaseous fuel. The power required for making the cement is sometimes purchased from outside sources; sometimes it is generated from the heat in the waste gases leaving the cement kilns, or generated at the plants direct from raw fuel. We have, then, as the possible requirements of fuel in the cement industry: (1) fuel for power generation, (2) fuel for drying raw materials, including coal before pulverizing, and (3) fuel for burning the raw materials to cement clinker. There is no essential difference in quality required in fuel for burning the materials by the wet and,dry processes. Fuel fob Power Generation As there is nothing peculiar to steam generation in a cement mill power plant as compared with other power plants this use classification of such fuel will be found in other reports of the Technical Committee. Fuel for Drying Raw Materials and Coal Any fuels capable of producing moderate temperature gases may be used for drying raw materials. There is no problem of material contamination from fuels at this part of the cement manufacture to be guarded against.

Jan 1, 1932

By T. M. Gurr

The United States is the world's leading producer of phosphate rock. In 1975 according to the US Bureau of Mines' statistics, 44.3 million tonnes (48.8 million st) of phosphate rock were produced in the United States, l which is 40.6% of the world's production.2 The major phosphate producing areas of the United States are located in [Fig. 1] and the production for 1975 is listed as follows: [ ] All of these areas produce phosphate from deposits which are of marine sedimentary origin. Occurrences of phosphate exist throughout the United States in numerous locations that are of both igneous and sedimentary origins. However, these other phosphate occurrences vary greatly in extent and economic significance. Georgia, South Carolina, California, Texas, Arkansas, Kansas, Iowa, Alabama, Kentucky, and Virginia are but a few of the states in which phosphate is thought or known to exist. The near future expansion will probably continue to be in, or near, existing producing areas, (i.e., Florida and North Carolina).

Jan 1, 1980

By R. Hogg, R. Schaller, P. Luckie

OVERVIEW This paper is a review of two fine particle processing unit operations - classification and mixing. It may appear that these two processes have nothing in common. In fact, the simplified symbols used to represent them on flowsheets - a tipped equilateral triangle such that the base lies along the vertical - are totally reversed. For classification, a splitting action, the apex of the tipped triangle is to the left of the vertical base. A horizontal flow arrow indicating input is drawn to the apex while two horizontal flow arrows indicating outputs are drawn from the top and bottom of the vertical base, respectively. On the other hand, for mixing, a blending action, the apex of the tipped triangle is to the right of the vertical base. Two horizontal flow arrows indicating inputs are drawn to the top and bottom of the vertical base, respectively, while a single horizontal flow arrow indicating output is drawn from the apex. Classification is the process whereby a collection of particles is separated into two or more portions differing in some physical or chemical property. Mixing is the process whereby two or more portions of particles differing in some physical or chemical property are combined into a collection of particles. The common bond that links them together in the same review is the fact that they both require dispersion of the particles in order to achieve successfully their individual objectives.

Jan 1, 1980

By J. Blodget Britton

IN the Journal of the Franklin Institute for May, 1870, there is published a description of a Colorimeter, together with a modification of the method proposed by Professor Eggertz, for determining combined carbon in iron and steel. An instrument of the kind there described, but of a little higher range, though in other respects not differing materially from the one originally made and used in the Iron-Masters7 Laboratory, I now submit to your inspection ; and I propose, also, to make some determinations minations with it for the purpose of showing how quickly they may be made, and enabling you to form some judgment of what reliance can be placed in the results. Professor Eggertz proposed only a single standard, and the solution to be tested should be diluted to exactly correspond in color with that of the standard, and the per cent. of carbon calculated after carefully noting and making allowance for the measures of water used in diluting. In practice, difficulty was found in bringing the color of the normal solution down to the exact shade of the standard; also other difficulties were met with in conducting the process, causing delay and interfering with the accuracy of the results. To materially overcome these, and after numerous attempts, an instrument such as is now before you suggested itself to me; and also I concluded to use a larger quantity of metal than directed by Eggertz, and, in addition, to filter the solution from its insoluble matter before making the comparison; and, more recently, to use an acid of just such strength as would completely dissolve the metal without the application of heat. Experimenting with these changes from the original method I obtained reasonably good results. The instrument, you will observe, consists of a series of tubes, sixteen in number, two and a half inches long, and about half an inch in diameter, standing upright, and securely fastened in a light, portable, walnut-wood frame, but separated one from the other so as to allow just sufficient space between to place for comparison the . tube containing the solution to be tested. The tubes are filled with

By John Fulton

The following table shows the shipments from the four Lake Superior iron-ore districts during the year 1887, and their total outputs from their beginning until the close of 1887.* It will be noted that the Menominee district is second in importance in its total output tonnage to the close of the year 1887. These ore deposits are found in jasper-slates and in the horizon between these and their associated clay-slates; in the latter they are true contact-deposits. They are found in this jasper- and clay-slate formation under varied conditions, yet, in all, certain characteristic laws are preserved. The angle of dip varies from 15° to 20°, and up to 85° and even 90°, with the horizon. The ore is rather soft, bluish-black in color, and is a hematite. It varies in thickness from a few inches to one hundred feet, or more. It is mainly "Bessemer" ore, containing 57 to 63 per cent, of metallic iron, and .03 to .07 per cent, of phosphorus. In the mining nomenclature of this range two conditions of the ore-lens are described by the terms "dip" and "pitch." The former is in common use in defining the relation of the ore-plane to the horizon ; the latter indicates the posture of the ore-body as it inclines east or west from its position at the opening of the mine. In the

Jan 1, 1888

By T. F. Adams, D. P. Morse

Tunneling is primarily an excavating cycle consisting of a sequence of operations: drilling, shooting, ventilating, mucking, and erecting supports, if necessary. However, the type and condition of the ground that is being worked, as well as the size and shape of the tunnel, determine the rate of advance. In addition developments in drilling, ventilation, mucking, and haulage equipment have contributed to faster tunneling. Geology: This discussion will be limited primarily to rock tunnels or those which require the use of explosives, and the cost and hazards depend primarily on the condition of the rock which may be broken, decomposed, and contain water with gas. Advance geological study is an important part of any tunnel work and helps to minimize serious miscalculations. The geology itself, at best, is a matter of experience and prediction and it is not so much a matter of the types of rock the tunnel may go through, but a knowledge of the class and intensity of the rock defects that may be encountered.

Jan 4, 1958

By Nicholas T. Camicia

A career in the coal mining industry today offers students one of the most interesting and challenging opportunities available in the industrialized world. As reserves of other fossil fuels dwindle in face of the world's demand for energy, it has become apparent that coal, once the king of energy sources, must be relied upon again as the major fuel for powering industrial growth in developed and developing nations. Centuries of coal supplies lie beneath the earth's surface, assuring the world of a steady, plentiful supply of energy until science and technology can produce a way to harness and efficiently use renewable sources, such as solar. The need to increase our use of coal during the last two decades of the 20th century is reason enough to believe that the future growth of the coal industry is assured. A major impediment to that growth might be backward national public policies that could restrict the full utilization of our coal reserves. These policies could result from overregulation and a failure of the public to recognize that coal use, with proper techno- logical safeguards, is compatible with our society's environmental-quality objectives. Communication of this problem and its solution is a major undertaking of the coal industry in the 1980s. At the end of the 1970s, the American coal industry was producing approximately 635 Mt/a (700 million stpy) of coal. To meet the nation's projected energy needs by 1985, the annual tonnage must be doubled. A similar scenario is predicted for the rest of the world. Such growth in the modern international business world will require huge additional amounts of capital, equipment, and people who know how to wisely raise and apply the capital; use the equipment productively; and deal with the many community, public, and governmental problems such expansion will create. Whether a student's interest is in actual mining operations, business administration, engineering, finance, law, industrial relations, marketing

Jan 1, 1981

By Brigitta Hassler

INTRODUCTION In the early 1960's research was begun in Sweden to improve the agglomeration of our domestic iron ore concentrates (5). Different agglomeration methods that were used in the building material industry were studied under the economic support from the Swedish Technical Council, the Swedish Board of Technical Development and by the Swedish industry. The research work was performed at the Division of Mineral Processing at the Royal Institute of Technology in Stockholm. All known agglomeration methods were reviewed and the methods were developed to produce superior quality agglomerates (6). The term cold bonding (in contrast to sintering) was introduced to describe the induration operation in these processes and this has been accepted internationally. Even though we used it mostly for steam autoclaving methods, it has come to describe a class of processes that use binding methods by pore filling. Schumacher in Germany discovered around 1907 that a strong material can be produced by mixing slaked lime with fine ground quartz and subjecting to a steam atmosphere under pressure at about 185ºC. This started development of lime-sandstone building materials and later on, in Sweden, the light-weight concrete. Schumacher also used the same reaction for briquetting iron ore concentrates by adding silica and lime, and autoclaving. The product seems to have been accepted for blast furnace burden and the process was used on an industrial scale until the 1920's. The sintering method has a small melting phase as diffusion medium and in the steam-autoclaving method a small quantity of water condensate at about 200°C serves the same purpose. Thus the induration process by the hydrothermal hardening methods is similar to that of sintering or heat treatment.

Jan 1, 1977

INTRODUCTION Engineering studies of many near surface coal deposits that are amenable to strip mining can be enhanced and expedited by the application of computer techniques for defining coal reserves and overburden and intraburden yardage and their stripping ratios. The case study discussed herein could be from the western coalfields of Colorado, Wyoming, or Montana; the lignite deposits of the Dakotas or Texas, or from the strippable coal seams of the midwest. Because the techniques can be applied so universally, the actual map locations are not identified. The same computing principles apply to one seam or multiseam deposits, and the capability of the computing programs and plotting routines to display the coal seams in plan and sections provide excellent base maps for further engineering planning and mine layout studies. MANAGEMENT OF DRILL HOLE DATA Drilling for coalfield information is usually done at much wider centers than for other mineral deposits. The geologic logs of the holes are generally quite simple, and frequently record only major lithologies and depths to the top and bottom of the coal seams, together with hole collar survey information. A header card is prepared for each drill hole showing: Hole ID Northing Fasting Elevation Azimuth Dip The header card can be followed by any number of downhole lithologic intercept records: [Hole Depth Lithology Hole ID From-To Coal] Less data errors occur if the computer cards are punched directly from drill hole logs, thus eliminating opportunities for mistakes in transcribing data. All arithmetic manipulations should be left to the computer to avoid as much human error as possible. The SURVEY program is run over the raw data file and all lithologic intercepts are computed and defined in XYZ space. BOUNDARY SURFACES-COAL SEAMS AND LITHOLOGIC UNITS The most useful computer program for defining coal seams in 3D space is a linear inter-

Jan 1, 1980

By Charles W. Goodale

The attention of the Institute has been called by Prof. John A. Church* and Mr. W. Lawrence Austin? to the free-milling ores of the Tombstone mines and their treatment, but the silver-bearing man ganese ores of the district have received only a passing notice. As these ores show some interesting peculiarities, and have yielded not less than 750,000 ounces of silver, they are worthy of some study. The Knoxville, Lucky Cuss, Luck Sure, and Wedge mines (named in the order of their importance) are situated along the northern border of the district. They have been the leading producers of this manganese ore, and possess the same general characteristics. Special attention will be given to the Knoxville, as it has been the one most extensively developed. The limestone belt, in which the Knoxville ore bodies occur, has an easterly and westerly trend, is about 1680 feet wide, and rests on granite on the north, the plane of contact being nearly vertical. It is overlain by quartzite, the contact-plane having a dip of 82°. Some mining has been done along these contacts, and a considerable amount of pay ore has been extracted, but development has been very superficial. The ore found along these contact planes contains very little manganese, and differs entirely from the ore in the lime stones. No attempt will he made to assign this limestone country-rock to a particular geological horizon, as no fossils have been found in it. Prof. Blake, in a paper on "The Geology and Veins of Tombstone, Arizona" (Trans., x., 334), speaks of the middle and upper strati-

Jan 1, 1889

IN welcoming the attending members of the Ameri-can Zinc Institute's Ninth Annual Meeting to St. Louis on April 18, the president of the Chamber of Commerce stressed the notable progress that had been made during nine years, marked by many price de-pressions and internal dissensions, while controversies between miners and smeltermen threatened to wreck the organization, prices dropped, and consumption grew languid for want of organized publicity and research. The reports and recommendations of Percy B. Butler, chairman of the Adjustment Committee, and F. C. Wallower, chairman of the Galvanizing Committee, might well be adopted as the institute's objectives. In reply to the speeches of welcome to St. Louis, Arthur Thacher reminded the delegates that the cor-ner stone of progress in the mineral industries was laid by the formation of the American Institute of Mining Engineers in Wilkes-Barre, Pa., in 1871, and the dedication of that organization to the exchange of ideas and methods of the winning of metals and non-metals from their crude state. The activities of the American Zinc Institute constitute, he said, a valuable phase of that work. Mr. Thacher forecast the treat-ment of 1 per cent zinc ore. After the reading of the report of the board of directors, in which Scott Turner and Louis Boschern were named as honorary members of the institute, a survey of world zinc conditions by A. J. M. Sharpe of London was presented. He held pres-ent conditions in China responsible for much of the present depression in zinc. World stocks on, April 1, 1927, were estimated as 52,900 metric tons. Adolph Boldt's paper on "Solidarity in Industry" was followed by a survey of the Tri-State district by Otto Ruhl, who emphasized the importance to the dis-trict of the organization of the Tri-State section of the A.I.M.E., which already has 135 members and asso¬ciates. He also mentioned .that flotation in the Tri¬State field is adding 1500 tons of concentrate to the weekly production. "Mining Economics" was the subject of Julian D. Conover, secretary of the Tri-State Zinc and Lead Ore Producers Association. He gave a detailed report on the costs of mining and milling in the district.

Jan 5, 1927

By C. C. RAE

The Texas Panhandle produced 18,677,000 bbl. of oil in 1932 as against 25,064,000 in 1931. The decline was caused by smaller market demand, since the Railroad Commission potential increased from 105,528 to 149,260 bbl. during the year. Well Completions, 1932 The development during 1932 compares with 1931' as follows: Year Wells Drilled Dry Holes Gas Wells Oil Wells Initial Pro- duction, Bbl. 1931 200 6 77 117 347 1932 136 18 28 90 603 Crude oil prices, small market demand, and lower allowable rate of production caused less drilling. Expiration of leases was one reason for a greater number of dry holes through forced drilling of questionable areas. The small number of gas wells reflected the influence of the business depression upon industrial and domestic gas demand, together with difficulties of franchise negotiations or pipe line extensions under present conditions. Probably much of the gas-well drilling was done on expiration leases, or to protect against drainage, and equalize withdrawals as between the various units held by each gas pipe line company. The increase in average initial daily production was due chiefly to excellent granite wash wells in the LeFors district developed by the Texas Co. and Skelly Oil Company. In the Panhandle district, comprising a major anticline with almost a million productive gas acres, the pools tend to merge in time, the development being confined to more productive areas. Hence separation into pools becomes a matter of time of development with some effort to keep dolomite, archosic and granite wash production separate. Many pools, like the Finley and Bowers, have mainly one type, but many leases and even individual wells produce from two zones. The oil production is usually closely associated with sea level, where proper porous formations

Jan 1, 1933

WHEN Georgius Agricola, in 155o, dedicated his now famous De re Metallica to the rulers of Saxony, Thuringia, Meissen, and other, smaller principalities, he included in his review of previous works on similar subjects reference to two books written in German: one, an "anonymous, rather disorganized account of assaying for metallic content and of metals," which must be the Probierbüchlein, the other, "dealing - with veins, written by Calbus of Freiberg, a well-known physician."* Calbus is mentioned a second time-and cited-at the end of the Third Book of De re Metallica. Comparison of the citation with the Bergbüchlein leaves no doubt that Agricola considered Calbus of Freiberg the author of the latter work, although all the editions of the Bergbüchlein known now were published anonymously. It is generally accepted by those who have dealt with the bibliography of the Bergbüchleint that Calbus was Ulrich Rülein von Kalbe, who served the City of Freiberg, in Meissen, as health officer in 1497, as member of the City Council in 1509, and as mayor in 1514 and 1519. He died at Leipzig in 1523. In connection with the very garbled description of the mining compass toward the end of Chapter 3 of the Bergbüchlein it is of interest that von Kalbe is supposed to have been not only a physician of repute but a mathematician, astronomer, mine sur-

Jan 1, 1949

By Kenneth Cottingham

The number of completions in 1944 in Ohio was only slightly greater than completions in the preceding year, but the initial daily volumes both of oil wells and gas wells declined considerably. The dry-hole ratio was a little lower than in 1943, even though in the year under review considerable effort was made to find new production. No new areas of consequence were discovered. Thirteen new gas pools, the largest of which was 1000 acres and the average 565 acres, were opened during the year. Eleven of these pools were in the Clinton sand, one was in the Oriskany, and one was in the Berea. Approximately 15 small pools might also be rated as discoveries, but because only one or two wells have thus far been completed in each, they cannot at present be properly evaluated. The latter pools average about 120 acres each. Some extensions were made to existing gas pools. The number of oil wells drilled was only one less than in 1943, yet compared with the year 1941, when twice as many oil wells were drilled, the difference is startling. Effective Aug. I, 1944, a blanket subsidy was granted of 35¢ per barrel on all Cleveland-Chatham, Coming, and Lima grades of oil, and 75¢ per barrel on Pennsylvania grade crude. The subsidy was authorized by the Office of Price Administration, with reimbursement to purchasers of the various grades made through the Defense Supplies Corporation, a branch of Reconstruction Finance Corporation. For several years the small operator, particularly the owner of stripper wells, was in a serious position. The subsidy has been a means of real help and, in addition to aiding the operator, it has prolonged the life of many small wells that otherwise would have been abandoned, with consequent loss of daily production and unre-covered reserves. It is questionable whether the price increase is sufficient to revive production of Corning grade, which has

Jan 1, 1945

Through the generosity of Sir Robert Hadfield, Honorary Member, the Directors of the American Institute of Mining Engineers are enabled to announce the Hadfield Research Prize of $1,000 for the best contribution to the publications of the Institute upon the general subject of The Different Forms and Combinations of Carbon with Iron, including those in Iron Alloys. The prize will be awarded at the Annual Meeting of the Institute in February, 1916, to the best paper upon this subject which is presented to the Institute before Nov. 1, 1915, provided such paper is deemed worthy by the Institute's Iron and Steel Committee. The following suggestions are also added for the guidance of those who may take part in this research. While' it is not desired to define closely the exact lines or scope of the proposed research, as it is advisable to make these as broad as possible, the object in mind maybe said to be generally as follows: To elaborate and find out the best methods of determining the forms of carbon in steel or iron, including those in iron alloys. A portion of the work would probably be a continuation of the researches which have in the past been carried out by Jullien, Abel, Muller, Ledebur, T. Sterry Hunt, Akerman, Arnold, Stead, E. D. Campbell, Hogg, Parry, Upton, and others. In a generic way, metallurgists now speak of carbides, sub-carbides, double carbides, special carbides, and other combinations. It is very desirable that these should be accurately defined and understood. It is also desirable to know whether there are other or new forms; if so, can these be separated and their characteristics obtained. It may be interesting to point out that the carbon compounds now definitely known are stated to number over 80,000. It is very probable, therefore, that there is room for much valuable and useful research to be carried out with the object of increasing our knowledge of the various combinations of carbon with iron, as probably some of these are still unknown

Jan 5, 1914

AT THE beginning of September, the French eased their pressure against Germany and allowed the latter to, be granted an arrangement for its reparation payments in kind according to the Lubersac-Stinnes agreement. The whole arrangement as to the German reparations is, however, but temporary. The Greeks suffered a disastrous defeat at the hands of the Turks in Anatolia, which rapidly resulted in the expulsion of the Greeks from Asia Minor, the Turks occupying Smyrna about Sept. 10. A few days after entering Smyrna the Turks sacked the city and finally set it afire, creating one of the most terrible destructions in history. At the same time their advance on Constantinople, together with their demands on the Allies, brought them directly in, con-flict with the latter and Great. Britain prepared for a new war, with doubt as to the support of France, whose political interests in the Near East are as different as their economic interests with respect to ;Germany. The Turkish situation became thus a threat against the peace of Europe. A revolution in Greece, followed by the abdication of King Constantine and the return of Venizelos to a function in the Government was one of the conse-quences of the defeat in Asia Minor. Civil war continued in Ireland, with more or less -bloodshed. Economically there has been no change for the better in Europe. In Great Britain there, are no signs of an -important trade revival. In Germany and Austria things are worse. French, Italian and Spanish affairs continue in a bad way. In the United States business is represented as "booming," but many people are inquiring where is the boom? About the middle of September Congress passed the tariff and the soldier bonus bills. The President signed the former and vetoed the latter, with a strong message that won praise among people who understand condi-tions. Congress tried to pass the bill over the veto, but failed. The President signed the tariff bill, which became effective Sept. 21. A severe handicap was thus imposed on American economics.

Jan 10, 1922

By F. E. Marcy

IT is not my purpose to write a lengthy article or to attempt the solotion of the problem I am presenting, but to call attention to what I believe an important issue, hoping that it may arouse in some one, or in some company, a sense of responsibility. I am referring particularly to modern up-to-date milling plants discharging tailings which under existing conditions cannot be further treated or from which a recovery cannot be made at a profit, but where a quantitative and qualitative analysis shows that a portion of these tailings might profitably bee treated, at some future time when our metallurgical knowledge has advanced, when we have cheaper power, chemicals, labor or other advantageous conditions. Early Methods In our early milling methods very little attention was given to the care of tailings. It was thought that if the mill could be located by a stream or a river where the final disposal of the tailings could be forever lost sight of, it was highly desirable. We can now see acid estimate what was lost in these rich tailings, not recoverable from the streams and the great rivers. Fortunately for many, the depositing of tailings in these streams and rivers was objected to by the farmers and finally prohibited by the State Legislatures. In looking back over our past milling methods, it seems that, the first endeavor was to make the maximum amount of money for a particular period, or year, regardless of the future, the depletion of the mine, or the conservation of the total mineral content. The dumping and sluicing of 3,000 tons per day, for a period of many years, of a copper tailing carrying

Jan 8, 1917

IN order to make his work easier, every master of any art whatever keeps always to the road that he has learned or that his skill or good judgment has shown him to be the best. Although there are various methods used in making moulds for guns, depending on whether they are large or small, nevertheless almost the same road is traveled in all. You must first know that it is necessary to make a pattern of wood or clay exactly as the gun is to be, with those ornaments of cornices and rings that you wish to be in the bronze. Let us suppose that you wish this pattern to be of wood. You must try to have for this a piece of fir as long and thick as you wish, dry, solid, and well seasoned, with few or no knots if possible. This should be longer than the gun by the length of the head and foot rests where it is pivoted [83v] so that it can be turned as on a lathe. On the end where the mouth is to be it should project out enough so that you can attach a feeding head at the top of the casting. You can make or have this pattern made round, fluted, spiral, or half fluted, as you like best, making the measurements exactly correct with all care and attention. Then two bearing trestles must be fixed firmly in the ground, one at the head and one at the foot, as is usually done with roasting spits and as you see drawn here. This done, if it is fluted, put the cornice pieces at the place where you wish the mouth to be and at the foot where the fire is applied. These are

Jan 1, 1942

By F. T. Lee

Directional dependence of strength and deformation properties of the Mount Waldo granite pluton in southeastern Maine is controlled by joints and microfractures whose orientations are linked to flow- induced alignment of microcline crystals. Longitudinal and cross joints which formed during cooling of the mass, as well as much younger sheeting fractures, are commonly associated with subparallel, discontinuous microfractures. The orthogonality of microfractures (open, closed; filled, unfilled; bubble planes) establishes the ease of splitting of the granite. The easiest splitting direction (rift) is subhorizontal, the second easiest direction (grain) is parallel to the cross joints, while the direction of least easy splitting (hardway) is parallel to the longitudinal joints. Static and dynamic measurements made in the field and laboratory established that structural features are responsible for the marked stiffness anisotropy of the granite. In the central part of the pluton the static Young's modulus in the north-south direction averages 31.1 GPa, and 20.9 GPa in the east-west direction; the stiffer direction being parallel to the long C-axes of microcline phenocrysts and microfractures as identified in outcrop, core samples, and thin sections. Vertical downhole sonic measurements of dynamic moduli ranging from 2.5 to 16.2 GPa appeared to be anomalously low when compared to the static horizontal values. However, the field sonic values were confirmed by laboratory sonic pulse testing of oriented cores. The field results reflected closely spaced layers of open horizontal microfractures. Those deformation and strength properties that are closely tied to bubble planes, filled microfractures, and microcline orientation could be extrapolated to greater depths with good hope of success.

Jan 1, 1984