Search Documents

By Don H. Baker

THE need for new or improved refractory materials has caused metal phosphides to be given renewed scrutiny. Some metal phosphides show high-temperature inertness, are exceptionally hard, and exhibit a marked resistance to chemical attack. Various metal phosphides have been prepared for study by direct combination of the elements,'-' by reaction of metal or metal compounds with phosphine or phosphorus trichloride,'"' by thermal decomposition of a metallic phosphate or phosphite,"-'8 and by molten salt electrolysis.19 Electrolytic preparation of phosphides of titanium, manganese, and chromium from their oxides is reported in this paper. An externally heated 3-in.-ID by 6-in.-deep graphite cell, that served as the anode as well as a container for the electrolyte, was used in these investigations, and a suspended, centrally positioned graphite rod served as the cathode. A closely fitting silicon carbide furnace liner minimized atmospheric oxidation of the crucible. Electrolyses were performed for predetermined periods and current settings. Preliminary research had indicated the more efficient current and potential settings that could be used. Upon completion of the deposition period, the deposit was hot-stripped from the cathode. The mass of crystalline deposit, plus occluded and adhering salt, was crushed to minus 10 mesh and hot-leached in dilute hydrochloric acid. The leached crystalline material was water-washed, dried, and sampled for analysis. Products were identified by X-ray diffraction and standard analytical procedures. Electrochemical studies were initiated to establish the optimum conditions necessary to produce manganese phosphide (MnP), titanium phosphide (Tip), and chromium phosphide (CrP). Among the factors studied were the operating temperature, the imposed current, and the electrolyte system. If the temperature, or imposed current, was too high, deposition of phosphorus resulted, and if either were too low, partially reduced lower oxides were deposited. The operating conditions established for repetitive high-quality production of metal phosphides of the MP structure are presented in Table I. The metal phosphide crystals varied in size, but all had a definite metallic appearance. Typical are the crystals of CrP shown in Fig. 1. Evaluation data and analysis of the crystals are presented in Table 11. Efforts to measure resistivity of these three compounds over the temperature ranges of 250o to 400°K were hampered by the small physical size of the crys-

Jan 1, 1968

By Charles L. Mantell, B. G. Shah

SINCE the beginning of the industry, commercial electrolytic manganese has followed the Shelton patent' among others, which called for the addition of sulfur dioxide in controlled amounts, to a purified manganese sulfate-ammonium sulfate at a controlled pH. Every attempt to eliminate sulfur dioxide additions has resulted in operating difficulties, chiefly solution of the deposited metal and lowered current efficiencies. Many replacements for sulfur dioxide have been proposed and studied, chiefly sulfur compounds, urea, thiourea, and proteins similar to those employed successfully in copper refining. It has been suggested that sulfur dioxide is a re-ductant for higher-valence manganese compounds, or that it is reduced by manganese metal in the deposit to hyposulfites or its compounds, and that these might affect the cathode film or the deposition potential, or the overvoltage of manganese. The additives were studied following the method of Mantel1 and Ferment2 who determined the feasibility of current-potential curves as an analytical tool for monitoring manganese elec trowinning solutions for metallic impurities: nickel, cobalt, silver, copper, zinc, molybdenum, cadmium, magnesium, and sodium. The individual effect of each on the standard polarization was determined for a range of concentrations. Not all affected the polarization curve; cadmium, magnesium, and sodium had no effect. Nickel, cobalt, silver, copper, and zinc yielded a correlation between transition current and concentration of impurity.

Jan 1, 1968

By J. A. Porter

In offering some data relative to this property, and the treatment of its ores, it is proper to say that a purely scientific article has not been attempted. It is hoped, however, that the economic conditions presented may be of interest to the members of the Institute, and that a discussion upon the concentration of the ore may throw some light upon a very unsatisfactory part of the work. The Smuggler-Union mines are located at the head of the San Miguel river, just south of the water-shed between Ouray and Telluride. The latter town, reached by the Denver and Rio Grande railway, is most picturesquely situated, at ail altitude of 8500 feet, in a narrow valley, the lower portion of which exposes only the sedimentary rocks. Along the sides of the valley, large masses of coarse alluvial deposits are left high above the present channel of the stream. Although much placer-work has been done, and some very rich material has been found, the limited extent of the isolated tracts has made placer-mining in this locality generally unprofitable. The valley terminates two miles above Telluride in an amphitheater around which walls rise abruptly several thousand feet. Here the company's mill is situated, being reached by a Bleichert tramway from the mines and also by a spur of the Rio Grande railway from Telluride. At this point, not only are the reddish sandstone and conglomerate beds exposed, but the contact between the conglomerate and the overlying gray volcanic breccia is plainly in view, even at a distance of many miles. A marked stratification is noticeable, indicating the successive layers of igneous breccia, locally termed trachyte. Throughout the entire region this is the favorite name among the miners for the rocks composing the igneous cap of the San Juan

Jan 1, 1897

JUDGE Samuel E. Schull, in the Court of Quarter Sessions of Monroe County, Pa., handed down a decision on July 2, declaring the Pennsylvania law for the Licensing of Professional Engineers and Land Surveyors to be in violation of the Constitution of the State of Pennsylvania and also of the 14th amendment of the Constitution of the United States. The case was that of George E. Stevenson, who was arrested in June, 1922, charged with the practice of the profession of land surveying without first obtaining a state license. Mr. Stevenson had had forty years of practical experience as an engineer and land surveyor, and as set forth in the findings "had attained unusual skill, distinction and reputation in his said profession, and, on said date and for a considerable period thereto-fore and down to the present time, was and is President of the Engineer's Society of Northern Pennsylvania." That part of the decision referring to the unconsti-tutionality of the act is quoted in full as follows: This matter now comes on to be heard on argument as to the constitutionality of the said Act of May 25, 1921, P. I. 1131. The defendant urges that the same is unconstitutional: First: Because it is in violation of Article 3, Section 3, of the Constitution of Pennsylvania, which provides: "No bill, except general appropriations bills, shall be passed containing more than one subject which shall be clearly expressed in its title." Second: That the same is discriminatory and, therefore, in violation of the 14th Amendment of the Federal Constitution. In this case, we: are confronted by the Act of Assembly bearing the title "an act to regulate the practice of profession of Engi-neering and Land Surveying; creating a State Board for Regis-tration of Professional Engineers and Land Surveyors; defining its powers and duties, imposing certain duties upon the Common-wealth and Political subdivisions thereof, in connection with public work and providing penalties." We meet in the title of this act, a recognition of the fact that it is the legislative intent to deal with two professions: First: Engineering. Second: Land Surveying.

Jan 8, 1923

By W. J. Sharwood

(San Francisco Meeting, September, 1915) CUPELLATION is well known to be one of the most effective methods of separating silver and gold from base metals and other impurities, as well as one of the most accurate means for their estimation. In the latter application it consists in absorbing in some porous medium the fused lead. oxide formed by the oxidation of the lead "bath," which carries with it the oxides of other base metals present. It has long been recognized that small amounts of both silver and gold were removed and absorbed together with the base metals, as well as being to some slight extent volatilized, and in work of the highest accuracy a correction is made for the "cupellation loss." Thus. in the assay of bullion this is done by means of "proofs" of like composition, which are manipulated throughout in precisely the same manner as the assay pieces, and are assumed to lose or gain like amounts. In the case of certain very rich ores and commercial products the loss is adjusted by assaying the cupel itself and recovering the precious metal absorbed, but this doubles the labor and does not remedy the loss by volatilization. Arbitrary tables have been drawn up by various authorities with the object of enabling a correction to be applied without the use of a check. These have been of very limited practical use owing to the fact that a number of factors affect the losses sustained. For a fixed amount of precious metal the loss varies with the amount of lead used, with the nature and amount of the impurities, with the porosity of the cupel, with the air supply, and above all with the temperature at which cupellation is carried on. Pure silver loses relatively much more than gold, but the loss in either is diminished by au addition of the other metal. The concentration of precious metal in the litharge increases as the concentration in the lead increases, but little work has been published connecting the two. If all other conditions remain the same the actual total loss increases, but the percentage loss diminishes, with an increase in the weight of precious metal treated.

Jan 8, 1915

By Donald Gilbert

PRIOR to July, 1919, the sampler at each mine of the Anaconda Copper Mining Co. in Butte did his work in his own way and was responsible to the mine foreman only. At that time, the sampling at all the company's Butte mines was placed in charge of a member of the geological department and stand-ardized methods of doing the work, were adopted. These standards were incorporated in a set of instruc-tions accompanied by blueprints representing typical conditions. The main features of the instructions were as follows: All samples to be cut at breast height and horizontally, regardless of dip of vein, and the horizontal width reported. A single sample to include not more than a 5-ft. width of the breast and to weigh not less than 4 lb. for this width. Where the vein is made up of two or more streaks of different hardness or mineral content, each streak is to be sampled sepa-rately and the average value of the combined width figured. If two streaks of ore are separated by a streak of waste, which is not sampled, in obtaining the average value of the breast the waste must be figured in with a zero assay. Drifts to be sampled in the breast after each round. Raises to be sampled for each floor raised. Each end to be sampled separately and the average width and value of the two ends to be used as the average of the floor. All veins cross-cut to be sampled along the side of the cross-cut, at breast height and horizontally. Where the vein strikes at an acute angle to the line of the cross-cut, the width of sample must be corrected to show the horizontal width at right angles to the line of strike of the vein. Rill stopes must be sampled across the full mining width. In square-set stopes, each set must be sampled separately along the line of the caps. Waste portions of the vein which are mined for filling must not be included in the sample.

Jan 2, 1922

By Donald C. Moore

INTRODUCTION Published laboratory procedures used by the major crusher manufacturers for estimating crusher size are based upon techniques developed in the mid 1940's. Specifically, the two largest U.S. crusher manufacturers are using the Bond impact procedure. Although the procedure is still in use, there is little confidence in the results. Unless the laboratory results fall within a preconceived range, personal experience is used for selecting the number of crushers and connected horsepower (Coleman, 1978). There have been numerous theoretical studies of the communition of particles. However, no procedure has been widely acclaimed for predicting crusher power requirements. Experimental studies have included breakage by slow compression, slow speed impact and high speed impact. Theoretical results have increased our knowledge of the comminution process, but the procedures have not been capable of analyzing the complex mechanism of industrial crushing machines. The purpose of this chapter is to review the empirical crushing procedures that have been used, including advantages and disadvantages. A new procedure which has been in development at Allis-Chalmers Corp. from 1977 to 1982 is detailed. Actual results of the new procedure on a concentrator feasibility study are included. EXPERIMENTAL GOALS The goals of a laboratory crushability procedure are accurate predictions of: (1) Rock crushability, measured as energy per unit mass. (2) Crusher product size analysis. A procedure capable of predicting these parameters should be inexpensive and require a minimum amount of sample. CRUSHABILITY TESTS Bond Impact Procedure F. C. Bond (1946) detailed the development of the pendulum impact device that is still used by the leading crusher manufacturers (Bond; Rexnord, 1976). The device (Fig. 1) is comprised of two bicycle wheels with 13.6 kg steel hammers tangentially attached to the rims. The hammer faces are 50 mm apart at rest. On opposite ends of the hammers lifting

Jan 1, 1982

By Carl Thieme

INDUSTRIAL specialization has rapidly created a demand for new and better alloys. A more thorough understanding of the requirements of specific industries and the discovery of processes by which it has been made possible to utilize certain metallic elements in larger quantities, together with greater purity in most virgin metals, has resulted in a great increase in the number and variety of alloys. This increase in the number of elements entering into non-ferrous alloy manufacture has increased the contamination in secondary metals, as received by the smelter. In order to successfully refine scrap of a much more complex nature it has been necessary for the smelter to install new equipment and to constantly search for new methods of refining as well as to improve the methods already in use. In some instances it is largely responsible for specialization in the secondary metal industry. It is usually necessary to remove the contaminating impurities in scrap or eliminate to a degree not objectionable, no matter how introduced. In order to know what metals or elements are of an objectionable nature, the smelter must make a study of the effect of single elements and combinations of elements on many of the physical and mechanical properties, such as strength, ductility, color, hardness, casting soundness, etc. The smelter of secondary metals must be able to utilize scrap materials of all kinds, for, sooner or later, most fabricated metal parts and the waste products formed during the process of manufacture find their way to the smelter. In addition, the smelter, in contracting for salvaged material from the producer, gets some undesirable and unusual materials. The value of secondary metals and the importance of their recovery has increased in recent years and it is no longer sufficient to recover the base metal only, such as copper from copper-bearing material, but it inessential that other elements present be recovered and converted into useful form.

Jan 1, 1928

By Hillary W. St. Clair

An equation is derived for the rote of reaction of a sphere of metal oxide in a restricted enclosure through which a reducing gas is flowing. The equation takes into consideration the reaction rate coefficient, transport through the gas and through the porous shell of reduced oxide, the rate of gas flow, THIS paper describes a mathematical study of the chemical and physical processes that determine the rate of reduction of solid metal oxide with a reducing gas. The study was a part of a theoretical study leading to the development of a mathematical model for the simulation of the thermochemical behavior of the iron blast furnace. An essential feature of such and the volume of- space surrounding the sphere available for gas flow. The equation is applied to experimental data on vote of reduction of iron oxide in hydrogen. The equation serves as a model for predicting the course of reduction of a particle of. metal oxide in a shaft furnace. a model is an adequate mathematical relationship defining the rate of reaction in terms of all the important chemical and physical phenomena that affect the rate of reaction. This includes not only the reaction rate coefficients, equilibrium ratios, gas composition, and temperature, but also the relevant physical properties of the oxide, rate of gas flow, and relative volumes occupied by gas and solid. In many previous experimental studies of the rate of reduction of oxides by hydrogen or carbon monoxide, the rate of reduction was assumed to be controlled primarily by the chemical reaction at the

Jan 1, 1965

By W. J. Shearer

A COMPARISON of statistics relating to coal min-ing in Great Britain and the United States leads one to suspect widely differing conditions and practice. A brief review of some of the conditions may enable American mining men to appreciate more fully the difficulties with which British engineers are faced, and to some extent explain why American, coal can be sold f.o.b. mine at the present time at about 50 to 60 per cent of the cost of British coal at the mine, and why British man-shift outputs fall far below American at present being less than 30 per cent. Bulman gives the average depth of 6-ft. seams. in Britain at 1350 ft., and of 2-ft. seams at 517 ft. George S. Rice states that 90 per cent of American coal 'is taken from less than 600 ft. Much English coal is taken below 2000 ft. and some below 3000 ft. The total influence of depth on cost is not always evident. Room work as known in America becomes less advisable with increasing depth, as pillars crush badly if left -for any length of time. A limited amount of bord and pillar work, taking very small amounts of coal in the first working, takes the place of room work, with rapid working of the pillars as soon as the panels are broken. Ventilation difficulties increase tremendously with depth and thinning coal. In America the chief use of air underground is to dilute gas. In Britain it serves a dual purpose, in many cases the amount of air cir-culated being far in excess of the quantity necessary to dilute gas to reasonable proportions. At great .depths rock temperatures exceed-95 deg. F., and great volumes of air are necessary for rock cooling. At these high temperatures humidity becomes an important factor. At present a great deal of research is under way to find methods of overcoming the troubles experienced with high temperature and humidity in deep mines.

Jan 8, 1928

By Henry M. Howe

If a bar of wrought iron or steel is suddenly cooled from a bright red-heat, the contraction which then occurs is considerably greater than the expansion previously caused by heating the bar, so that its final length is considerably less than its initial length. Mr. Thomas Wrightson has investigated this phenomenon,* and has shown that not only does this permanent contraction occur on sudden cooling, but, if the heating and cooling be repeated, say fifty times, a further permanent contraction occurs at each successive cooling. In Mr. Wrightson's opinion, this contraction cannot be explained on mechanical grounds, and he ascribes it to some molecular change caused by sudden cooling; but I think that we need not invoke mysterious molecular changes to explain this phenomenon, which appears to me to be due to very simple and purely mechanical action. Let us consider the cooling as divided into two periods, in the first of which the exterior or skin of the bar becomes almost completely cooled, and hence tends to contract almost to its initial dimensions, while the still hot arid plastic interior contracts but little; in the second period the already cool skin remains nearly constant in temperature, and hence tends to contract but little, while the interior cools from a comparatively high temperature to the ordinary temperature, and hence undergoes great contraction. The excess of the contraction of the skin over that of the interior during the first period tends to make the bar bulge in the middle of its length. This, as well as the decrease of density which occurs, Mr. Wrightson correctly explains. The interior of the bar just sufficed to fill the skin when both were in their initial condition, before being heated at all. At the end of the first period, the volume of the still hot interior is more than the now contracted skin can hold while maintaining its initial shape; and the effect is much the same as when we powerfully blom into a soft India-rubher Lag of the shape of the skin of the bar—it bulges, and tends to approach the spherical shape, in which the ratio of surface to

Jan 1, 1886

By H. E. Rowen

As high grade iron ore deposits dwindle and costs rise, sintering becomes more and more important. The steel industry is now faced with beneficiation problems once peculiar to nonferrous work. Succeeding articles describe recent advances in this field. Here is presented the first chapter of a history still being written. SINTERING, for the purpose of this discussion, is defined as the art of burning a solid fuel with 90 to 95 pct ash content. Considering problems of combustion involved in keeping a home furnace burning properly with 12 to 20 pct ash in the fuel, it is evident that combustion represented by the definition has to be right or nothing is going to happen. Our forefathers discovered that many ores containing metals essential to the steadily rising standards of living were associated with elements such as sulfur and arsenic, which had to be removed before refining. This they did by utilizing the solid fuels they had available-the sulfur or other readily combustible components-to create roasting heat. One of the early methods is demonstrated in an old woodcut of the roast heap, Fig. 2. Ore was broken into chunks, piled on an ignition layer of solid fuel-logs in this case-and then. ignited. The sulfide ores roasted as the sulfur burned out. As shown in the background, the countryside was rapidly denuded of all vegetation by the great quantities of SO2 and other liberated gases.

Jan 1, 1961

I. N. KNAPP, Ardmore, Pa. (written discussion *).-The writer would first call attention to the fact that the mid-Continent field was credited from 1900 to 1915 with a production of about 641,000,000 bbl. of oil with-out any burdensome water troubles being reported. In fact, the authors say the conditions were not acute until about two years ago when the unusual conditions in the deeper oil fields were first encountered. The writer disclaims any personal knowledge of the district mentioned but, from the experience he has gained in directing drilling in various fields by both the cable-tool and the rotary methods and also in plugging and cementing wells, he fails to see how the analysis of water trouble given in the paper under discussion could be of any practical assistance in solving the problems so vaguely outlined. Possibly it might induce academic discussion, if not limited to practical operating conditions. A recent bulletin of the Bureau of Mines gives definite and practical statements that can be easily understood by one skilled in the art of drilling wells and heading off water troubles. From an operating standpoint subsurface knowledge must be based on logs of completed wells. Absolutely no one can have such knowledge as that indicated in Fig. 1 of the paper in question without drilling wells, and no one can question such facts when disclosed by the drill. Under classification of water the paper states "This water (primary) cannot be exhausted from the sands, but its encroachment can often be checked and so directed that wells need not be abandoned, until most of the available oil is secured." This is a live question to the writer. A couple of years ago he had some wells drilled and found the conditions comparable with sands A and D of Fig. 1 with B and C left out; but nothing in the paper, so far as can be found, indicates how this water encroachment is or can be checked or directed particularly under the High heads named.

Jan 5, 1919

By Joseph C. Kieffer

The Duquesne property of the Callahan Zinc-Lead Co. is about 20 miles east of Nogales, in southern Arizona. One mine is near the mill, but most of the mill feed is hauled in by truck from a number of small mines. The same sulphides are found in all the ores, in general, but the amounts vary considerably. All ores contain silver, copper, lead and zinc minerals but one mine ships ore high in silver and lead and low in copper and zinc; while another mine ships ore high in copper and zinc, and low in silver and lead. The common sulphides are galena, carrying most of the silver; chalcopyrite; sphalerite, carrying iron in solid solution; and pyrite, in a gangue consisting of limestone, quartz and garnet. Mineralization is fairly coarse. At the present grind of about 66 per cent minus 200 mesh most of the sulphides are liberated A small amount of chalcopyrite is locked up with the sphalerite and cannot be liberated at an economic grind, and the copper carried into the zinc concentrate with the sphalerite accounts for the comparatively poor recovery of copper in the copper-lead concentrate. Production oF Two Concentrates The milling problem, which was complicated by the extreme variation in the grade of the feed, was first attacked with the idea of producing a silver-copper-lead con- centrate and a zinc concentrate, both with satisfactory grades and recoveries. By February 1941, it was felt that these objectives had been attained, when the grades of the various products and the recoveries were as shown in Table I. A rough outline of the flowsheet and reagents used is as follows: Minus ¾-in. feed to a 7-ft. by 36-in. Hardinge ball mill working in closed circuit with a 36-in. Wemco classifier. The classifier overflow passes to the second cell of an 8-cell bank of No. 18 Special Denver Sub-A flotation machines (volume, 22.5 cu. ft. per cell). A rougher concentrate is removed from the second to the fifth cells inclusive, and returned to the first cell, which is the cleaner. A scavenger concentrate is removed from the sixth, seventh, and eighth cells, and returned to the third cell. Consump-

Jan 1, 1943

By Foster Bain

THOUGHTFUL people have raised questions as to how long nature's bank could continue to accept our drafts. These questions came to the fore so persistently, and there were so many evidences -such as the failure of natural gas in Indiana, the increasing scarcity of lumber in the Lake Superior region, the progressive sterility of Southern farm lands, the choking of the Sacramento River by tailing-point-ing to possible danger from overdraft or to misuse of resources and opportunity, that President Roosevelt called a conference which assembled at the White House on May 13, 1908, to consider these and related questions. This, the first great Conservation Congress, had a wide and beneficial influence on the thought of the world. It profoundly influenced the course of succeed-ing events and, while even yet there are sharp dis-agreements as, to the wisdom of much that has been done in the name of conservation, I believe that thoughtful men, and engineers especially, agree that the time had come when sharp attention was properly called to the waste that accompanied development of our resources. RESOURCES LARGE BUT NOT INEXHAUSTIBLE In 1908 there was a surprisingly large number of men, who should have known better, prepared to argue that our resources are "inexhaustible." No competent mining engineer, of course, believes that, as regards minerals at least. They may be, and, in most cases, fortunately are, large; as to many of them our knowledge is too general to permit measuring the reserves; but we know now, and I think the public appreciates, that there is a limit to our supply of gas, oil, coal, iron, and metals. Indeed, with the inten-sive study made necessary to meet the demands of the war, and the more careful accounting required by the newer systems of taxation, depletion has become a common word, and that mines are wasting assets has become a platitude.

Jan 8, 1922

By L. C. Morganroth

CARBONIFEROUS CLAYS FROM a geological standpoint, but scant attention has been paid to fire-clay beds. Only within the last few years have they been the subject of individual investigation, prior to this time having been considered only in their relation to coal seams. While the relative importance of coal and fire clay is still immeasurably in favor of coal, yet an industry as large as that of fire clay is entitled to a measure of attention. A discussion of the Carboniferous clays is practically a discussion of the clay beds in the Appalachian basin, since more than 90 per cent. of these clays mined are from this region. The clays are confined to the northern end of the basin, or the States of Pennsylvania, Ohio, Kentucky, Maryland and West Virginia, ranking in importance about in the order named. The clay deposits of the Carboniferous period have been divided into two classes; those found in the Pottsville conglomerate series of rocks, and all those that are found in the formations above, for the reason that the clay beds above the Pottsville series all resemble each other in properties, composition and appearance, and all are distinctly different from the bed found in the Pottsville formation. The bed of clay found in the latter formation is unique in that flint clay is practically restricted to it. (A variety of flint clay is occasionally found in these upper deposits but this is in such small amounts as to be negligible.) Carboniferous clays occur between stratified rocks; sandstones, limestones, etc., in the same manner as coal veins. They are often accompanied by a coal vein although where the clay is of a workable thickness the coal is generally too thin to work. The clay beds are sometimes known by the name of the coal seam at which horizon they occur. Clay beds may be from a few inches up to 20 ft. in thickness. They may consist of all soft clay all flint or both soft and flint.

Jan 2, 1916

By Theodore B. Comstock

Prior to 1885, the College of Engineering in the State University was under the care of such professors and instructors as were required for efficient work in the Schools of Mechanical Engineering, Civil Engineering and Architecture. The development of the coal and other important mineral resources of the commonwealth led gradually to a considerable demand for instruction in the branches more closely related to mining engineering, and a very creditable effort was made to meet this want by arranging special work in the field and in the laboratory for students of mining and metallurgy. This plan, while it gave much added labor to several already heavily taxed professors, caused such students to become something like undesirable excrescences upon the regular courses. But its partial success gave abundant proof of the real necessity for a complete course in Mining Engineering. The famous Braidwood disaster emphasized anew the importance of thorough training on the part of those to whom the responsible duties of mining must be confided. As is well known, a very excellent beginning was made some years ago by the Legislature in the matters of inspection and regulation by the enactment of a reasonably effective law, which was afterward much improved.* About the date of the last Acts, it was deemed wise to enlarge the facilities at the University arid to furnish adequate training for the increasing number of applicants. Accordingly, in August, 1885, the writer was requested to assume the duties of the professorship, it being the expressed desire of the Board of Trustees and the Regent of the University that a School of Mining Engineering should be founded which might eventually come to rank with the other engineering schools already flourishing here. It is the main object of this paper to state plainly the steps thus

Jan 1, 1887

By E. P. Klier, Volker Weiss, George Sachs

IT has been shown that the isothermal transformation of austenite in a special steel can be modified by isothermal holding in the high subcritical transformation range.' Since this treatment potentially leads to increased hardenability, limited testing has been completed to determine if the stabilization effects observed with this treatment can be used to advantage in the heat-treating of 4340 steel. As an index of the effects of the several austenitizing treatments on the hardenability of the steel, Jominy-type hardenability tests were completed for specimens 2.5 in. in diameter and 8 in. long. Since the steel studied is to be used at strength levels where notch sensitivity is of major concern, notch sensitivity after selected austenitizing treatments has been evaluated by notch tensile tests for several specimen sizes. The steel composition and the austenitizing treatments are given in Table I. The test specimens are presented in Fig. 1. The hardenability data are given in Fig. 2 and the notch tensile properties are presented in Fig. 3. The hardenability of the steel investigated when determined by use of the standard Jominy test specimen2 as high and remained essentially unchanged for the different austenitizing treatments. For the larger test specimen, as has been shown by other investigations," the characteristic hardenability indexes are changed and it becomes possible to isolate austenitizing treatments which promote maximum hardenability. The stepped austenitizing treatment promotes higher hardenability as is indicated in Fig. 2. The evaluation of notch sensitivity for very high strength steels is best accomplished by means of the notch tensile test. The experimental conditions of the test, however, modify the notch strengths measured, and in the present experimentation an effort was made to achieve a limiting notch condition by fixing the notch root radius at 0.001 in. while the specimen diameter was allowed to increase from 0.3 to 1.1 in.* For this root radius the notch strength, 0.3-in.-diam specimen, and this trend differs from that for the larger specimens. At the highest tempering temperatures the 1.1-ip.-diam specimens yield comparable results for the austenitizing treatments compared. However, as the tempering temperature is progressively lowered below 800°F, em-

Jan 1, 1958

By George E. Aiken

Modern high speed bucket wheel excavators (BWEs) can dig materials which power shovels can't handle without blasting. Yet these machines are not used in any large, open pit ore mines in the United States. American mining has been slow to use the wheel's special capabilities of high production volume at low cost, due perhaps to a traditional familiarity with shovels and draglines and/or the lack of data of BWE operation, design and cost. Of course, shovels and draglines can not be replaced by BWEs in all cases, but under suitable conditions bucket wheels can out-perform other conventional excavators and simultaneously permit significant operating savings. The latter aspect will become increasingly important to American mining men because as more low to medium grade orebodies are found in regions of thick overburden, better and cheaper ways of uncovering them must be developed. Typical of such areas are the thick alluvial fans of the Southwest and the glacial drift areas in northern regions. Much of this material would handle well with a wheel excavator without blasting, although ripping might be necessary in some cases.

Jan 1, 1966

By Peter Q. Nyce

Law is as old as civilization. In its early stages the so-called law of the jungle, "the survival of the fittest," was entirely operative. Man was quite largely a law unto himself and was likewise his own lawyer. As civilization developed and individuals segregated themselves into bands or communities, man-made laws became a reality, the individual sacrificing certain privileges for the benefit of the band or community in which he was privileged to live. Our present system of law is a continued development of that process. Very early in this development the exigencies of the occasion called into being classes of individuals who were given to study the laws then existing, and this group became known as lawyers. They advised what could or could not be done under existing laws. They were the aggressors in formulating new laws and principles under which the communities must live. Concurrently with the development of the law and the lawyer, the engineering profession was born. In our early civilization, each man was his own engineer; he built his own home, constructed his own bridge, and provided his own means of conveyance. As civilization became more complex, technical study was required to consummate projects and thus meet the requirements of an expanding community. The engineering profession assumed this burden. Both groups were human and thus susceptible to human mistakes and errors. It was Macaulay who said: "The world generally gives its admiration not to the man who does what nobody else ever attempts to do, but to the man who does best what multitudes do well." BiRth of Petroleum Industry In 1859, by the completion of the Drake well in Pennsylvania, the petroleum industry as we know it was born. Its rapid progress since that time has been both extraordinary and remarkable. The zeal of the individual operator to secure all possible oil in the shortest time, even to the extent of bringing into possession a part of the oil underlying a neighbor's property, developed unnecessary drilling, wasteful methods of recovery, great loss of gas, the early abandonment of property with much unrecovered oil thereunder. Such methods, plus

Jan 1, 1931