Search Documents

By L. Stone, H. Margolin

The Ti-C-N and Ti-C-O systems were investigated in the temperature range from 500° to 1400°C and in the composition range up to 2 pct C and 5 pct N or 0. Characteristic isothermal sections at 800°, 900°, 1000°, and 1300°C are presented. The Ti-N-0 system was studied in the temperature range from 900' to 1400°C with alloys containing up to 6 pct total alloying content. Characteristic isothermal sections at 1000° and 140O°C are presented. Melting-point data for all three systems are also included. THIS paper reports on one of a series of investi-gations which have been conducted on the phase diagrams resulting from interstitial alloying with iodide titanium. The other investigations involved delineation of the binary systems with carbon,' nitrogen and boron,h and oxygen. The Ti-0 binary system has also been investigated by Bumps et al.' In varying degrees, each of these interstitial elements has been shown to stabilize the low temperature a modification of titanium1-5 and each forms a face-centered cubic TiX compound (henceforth designated 6). In addition, the Ti-N and Ti-0 systems reveal a low temperature tetragonal phase (6) formed by a peritectoid reaction between a and TiX Experimental Procedure The development of experimental techniques for the study of titanium alloy systems has, to a large extent, become standardized. In this investigation, the equipment and procedures described in detail by Cadoff and Nielsenl have been used. Arc Melting: In general, binary alloys with carbon, nitrogen, and oxygen, prepared in the composition range of interest in this investigation, show negligible composition changes during arc melting. However, the possibility of the formation of some gaseous combination of alloying elements such as CO, CN, or NO during the preparation of these ternary alloys was considered. Calculations showed that the evolution of only 0.05 gram of such a gas would be detectable as a pressure change in the closed system used during preparation of these alloys. Such pressure changes were not observed. Consequently, nominal compositions have been used in plotting the data. The compositions of the materials used in the preparation of the alloys are shown in Table I. After melting for 3 to 5 min at 275 to 350 amp, the alloys were checked for homogeneity by microstruc-tural examination. Alloys containing up to 1 pct C were homogeneous in the presence of less than 3 pct N or 0. At higher alloying contents, some inhomo-geneities in the carbon distribution became evident. Alteration of the melting procedure toward longer times and higher currents did not improve the homogeneity of these alloys. Ti-N-0 alloys were homogeneous in the range to about 3 or 4 pct total alloying addition. Beyond this, almost all of the specimens showed as-cast microstructures consisting only of the phase. Consequently, inhomogene-ities could not be detected by examination of micro-structures. Ten alloys from each of the systems were analyzed for two of the elements present (oxygen being omitted in all cases and titanium being omitted in the Ti-C-N alloys). In all cases the analyses were found not to be sufficiently precise to serve as criteria for the total composition of these alloys. On the basis of phase distribution in heat-treated alloys, however, it appears that carbon is distributed throughout the alloys most uniformly, with oxygen and nitrogen following in that order. Heat Treatment: Specimens for heat treatment were wrapped in titanium sheet before sealing in the argon-filled quartz capsules. Heat-treatment times varied from 100 hr at 800°C to 0.5 hr at 1400 °C. After heat treatment the specimens were quenched by breaking the capsule in water. With the exception of alloys in the low composition region, heat treatment did not have an appreciable effect on the as-cast microstructures. Metallography: Following heat treatment, the specimens were prepared for metallographic examination by grinding on emery paper and electrolytic polishing. For the majority of the specimens a 10-sec etch with Remington "A" agent (25 pct HNO3, 25 pct Hf, and 50 pct glycerin) adequately

Jan 1, 1954

By A. J. May

THE Star shaft is near the north boundary of the group of mining claims belonging to the Ground Hog Unit of the American Smelting and Refining Co., near Vanadium, N. Mex. The shaft bins and surface plant are served by a siding from the Atchison, Topeka and Santa Fe railroad, and this factor of railroad transportation influenced the choice of site. This paper describes the shaft sinking only, and does not cover the surface plant or other parts of the mine or its equipment. A. J. MAY is Engineer in Charge of Shaft Sinking, Ground Hog Unit, American Smeling and Refining Co, Vanadium, New Mexico. El Paso Meeting, October 1948. TP 2737 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Nov. 29, 1948; revision received June 22, 1949. Experience with this shaft seems of interest because of the mechanical mucking, good rate of progress, and the costs obtained at the present level of labor and material costs. The shaft has four compartments, as shown in fig. 1. Equipment: Riddell Mucker: The mucking was done by a clamshell bucket and a Riddell mucker, which, as in other shafts sunk with this machine, consisted of a carriage mounted on axles with double flanged wheels that traveled back and forth on a swinging track, parallel to the long axis of the shaft (fig. 2 to 6). Three air motors were mounted on the carriage; one hoisted the clam, one operated the bucket opening and closing device, and the third moved the carriage along the track. The carriage was designed with guide shoes and could be hoisted to the surface in either skip compartment without trouble (fig. 4). During blasting operations the clam was tied on the rails and the carriage was hoisted up a few sets to protect it from flying rock. No attempt was made to hoist the carriage and clam together lest the clam catch in the timbers. The track on which the carriage operated was built of extra heavy 6 in. pipe with 1x2 in. strap welded on top for rails. A Yzx4 in. angle was welded on the bottom of the 6 in. pipe with a 1 in. round rod welded in the angle for a filler and additional strength. The end or cross pieces of the track which kept the track to gauge, were also made of reinforced, heavy 6 in. pipe and were bolted to the long members on which the carriage traveled (fig. 2 and 3). This section of track was used, instead of heavy railroad rails, for two reasons: (1) this section would bend before it snapped and was much safer for the men in the bottom; and (2) it was a better blasting shield, and protected the timbers better, in fact, only five wall plates were broken by blasting in 1926 ft of shaft, although 150 to 225 lb of 40 pct powder was loaded per round, depending on the ground conditions. The swinging track was supported by four % in. hoisting cables anchored to the end plates. There were also four safety cables fastened two to three sets above the carriage, which would catch the carriage if one of the supporting cables should fail for any reason (fig. 7). Clamshell Buckets: Two clams were used, each of % yard capacity, both manufactured by Blaw-Knox, Nos. 662 and 663. The No. 663 clam was 4 in. wider and 5 in. shorter than the No. 662, but seemed to dig and load more satisfactorily. It was easier to hoist and lower when it came up for repair. It did not turn over as easily, had less spill

Jan 1, 1951

By Leonard L. Melton, Calvin D. Saunders

The design and performance of many operations common to the petroleum industry depend upon the unique properties of a class of materials known as non-Newtonian fluids. The art of measuring and describing these properties, called rheology, has fallen far behind the field applica-tion of these fluids in this industry. Empirical methods are still employed although theoretically sound methods of analysis are now available. This paper illustrates a completely general method of analysis of the rheological properties of non-Newtonian fluids which id independent of the type of viscometer employed and also the rheological type of fluid encountered except those of a thixo-tropic or rheopectic nature. Values of the rheological properties of a fluid obtained using this method of analysis are based upon an absolute scale of measurement, eliminating the necessity of employ-jng arbitrary concepts of the flow properties of non-Newtonian fluids, The fundamental nature of this method of analysis is further demonstrated by evaluating the precision with which measurements have been made of these rheological properties by employing a dimensionless criteric: —the Fanning friction factor-Reynolds number correlation. INTRODUCTION Non-Newtonian fluids are not new in the petroleum industry. Particular properties of non-Newtonian materials have been recognized and used to advantage in drilling fluids and have found excellent application in the hydraulic fracturing process.'.' While usage of these fluids is not new in this industry, the art of measuring and describing their rheological properties is still in its infancy. This is reflected in the accepted method of evaluating drilling fluids, API RP 29, (1950), which recommends a one point "viscosity" measurement. These shortcomings are recognized by various groups in the industry and more adequate methods have been prposed.3,4 The efforts Of these people are to be commended; but, at the same time, the limitations of their method of analysis and viscometer must be appreciated. This method Of analysis is applicable Only to Bingham plastic fluids as is pointed out early in their articles. The consistency of a Bingham plastic fluid must also lie within the range of the viscometer which is also well defined by the author. It is believed that the apparent simplicity of this method of analysis and the utility Of Operation Of their viscometer will soon make the terms non-Newtonian fluid and Bingham plastic fluid synonymous as used in this industry; a tendency which has already been encountered. Application of this method of analysis to a non-Newtonian fluid other than a Bingham plastic can lead to erroneous results. The field of rheology has long been hampered by the adherence to arbitrary concepts of Of of the flow properties Of non-Newtonian fluids. This has resulted in the design and operation of viscometers so as to fulfill these concepts rather than following the more logical method of analyzing experimental data so as to yield a fundamental truth. completely Bingham proposed the concept Of plastic flow and yield asu rement. data presented by Buckingham could hardly be interpreted so as to substantiate this theory; but rather succeeded in establishing the fact that compliance with this flow concept could never be realized in the capillary tube vis-cometer.5 Bingham, in reply, sug-gested "Rather than complicate our formula, it would seem to me a much better plan to so change the conditions of flow that the formula will be linear... Reiner0 stated .This plan has been followed by me in collaboration with Miss Riwlin. . . . From the present paper (Reiner and Riwlin, 1929) it will be seen that it is possible to choose the conditions of flow so that the formula based on Bingham's law of plastic flow remains linear. This is realized in the rotation viscometer," Thus, a viscometer, with design and operation based on the Reiner and Riwlin equation for plastic flow, is restricted to a specific range of flow

Jan 1, 1958

By C. G. Dunn, F. W. Daniels, M. J. Bolton

IN recent investigations1. a data on relative grain boundary energies in silicon iron have been obtained. The present investigation is a continuation of this work along similar lines for the purpose of obtaining additional information on boundary energies. One aim has been to extend the data for a (110) series, which was formerly studied,' to small differences in orientation, since a recent theory3,4 based on a dislocation model of grain boundaries predicts a E. ? (A-ln ? )* form of energy curve for small differences in orientation. Another aim has been to provide data for a (100) series—all grains having (100) planes parallel with the surface of sheet speci-mens—and to compare the results with the predicted form of energy curve. Finally, information on the nature of approach to equilibrium conditions was to be obtained through observations on the movements of grain boundaries. Recently published papers2,3,5 have treated the mathematical problem of expressing equilibrium conditions for grain boundaries for the general case when boundary energy depends upon boundary orientation. The equilibrium equations, which relate equilibrium angles and grain boundary -free energies, contain additional terms that express the variation of energy with boundary rotation. It has been necessary in the present investigation, however, to neglect these additional terms since no data for their evaluation were available. Dropping the additional terms leads to the following approximate equations which were used: E12/sin ?3 = E18/sin?2 =E28/sin?1 or those of the form: E28 + E13 cos ?3 + E12 cos ?2 = 0 Experimental Procedure Except for sample F1, all specimens were made from two lots of silicon iron called C and L respectively. The compositions of these are listed in table I. In the preparation of 12 three-grain specimens for the present investigation, a controlled grain growth technique, which has been described previously,' was used. After preparation, the specimens were notched at the boundaries to shorten them as a means of providing more rapid approach to equilibrium in the anneals. Initial grain boundary angles were determined from micrographs taken at X500. Seven anneals, totaling about two days at 1300°C and two to four days at 1400°C, were run in an atmosphere of pure dry argon as described in a previous paper.' Boundary changes generally could be followed without metallographic surface preparation, because thermal etching occurred during the anneals. These observations indicated angle changes of as much as 35" in some instances, with the major changes occurring during the first anneal. Annealing was discontinued when the angles reached stationary values. Fig. 1 gives a schematic diagram for purposes of defining crystallographic and boundary directions for three grains with common plane parallel with the sheet. Differences in orientations (expressed by A) are the angles between [00l] directions. They can be calculated with the aid of the ?'s. The grain boundary angles can be calculated from the w'S. Results Results are given in table 11. Types of crystal-lographic planes refer to those parallel with the sheet. Orientations are given in terms of [00l] direc-tions as shown in fig. 1. Except for grain 3 of specimen H6, which was unintentionally tilted 7" out of a (100) plane, all grains generally were within 1" or 2" of the plane specified. The directions of boundaries were measured generally to within 1" on both upper and lower surfaces, and the average direc- tions were determined for use in calculating the grain boundary angles. Variations in grain boundary directions refer to deviations from average directions. Boundaries near the junction point for all specimens generally were very close to perpendicu-

Jan 1, 1951

By M. Muskat, F. Morgan, R. G. Russell

Core experiments with radioactive tracers are reported in which an artificial radioactive material, radiovanadium, was used in aqueous solution in a study of the mobility of connate water. Sandstone cores saturated with active water were first oil-flooded to simulate virgin sand conditions in which the pores are filled with oil and connate water. They were then subjected to flooding with inactive water. Measurements were made of the activity of various portions of the effluent as well as the activity of the core after the flooding process was completed. In additional experiments the distribution of activity along the core was measured during the flooding process. In still other experiments direct flooding tests were made on cores fully saturated with active water. In all cases it was found that after injecting into the core a volume of inactive water equal to a pore volume, the effluent contained more than 80 per cent of the active content originally in the core. It is felt that these results imply a high degree of mobility of the connate water when subjected to flooding, although at least a partial contribution of the effect of tracer transfer within the core cannot be definitely excluded. The implications of this result with respect to water-flooding, core analysis and electric logging are discussed. A better approach to determining the connate water saturation of oil-producing rocks, by measuring the fluid content of core samples at the surface, is by the use of crude oil or oil-base muds as the coring fluid. Although water flooding is of considerable importance in the recovery of ail, comparatively little is known with certainty about the role played by the connate water during the operations. Two possibilities exist. Either the connate water is retained in the formation while the flood water sweeps past, or it is pushed along to a greater or lesser degree by the flood. Thus far no explicit recognition in terms of quantitative studies appears to have been given to the displacement of connate waters by the intruding extraneous waters, although such a possibility might be important in determining the efficiency of the oil -displacement process in water-flooding operations, especially in argillaceous rocks. On the other hand, it is a common observation that the first water produced with the oil as a result of water-flooding is definitely saline.*.' Similar questions regarding the mobility of the interstitial water arise in the quantitative description of the advance of edge-water drives. In the interpretation of the water saturations determined from core analyses, when coring with water-base muds, it is generally assumed that the drilling fluid merely adds to the connate water without displacing the

Jan 1, 1947

By D. J. Schmatz

DISCUSSION OF RESULTS The qualitative correlation between low-temperature ductility and prior high-temperature creep strain in nickel obtained in this investigation confirms the result obtained on high-purity brass by Chen and Machlin. However, the quantitative effect is much smaller in nickel. Comparison can be made on the basis of a prior high-temperature strain that is a certain percentage of the total high-temperature elongation to rupture. In the research of Chen and machlin, the prior high-temperature strain of 1/2 pct equaled 8.5 pct of the total high-temperature elongation at rupture. For nickel, in our experiments, 8.5 pct of 21.2 pct equals 1.8 pct. For eh = 1.8 pct, the loss in ductility in percent equals x 100 = b.5 pct. That is, for equivalent bo Formation of Beta Manganese-Type Structure in Iron-Aluminum-Manganese Alloys D. J. Schmatz IRON-aluminum alloys have gained much interest in the past few years for use as a base material for elevated-temperature alloys because of their excel- high-temperature strain the loss in low-temperature ductility is 8.5 pct for nickel as compared to 60 pct for pure a, brass. It is also interesting to note the observation that in nickel the low-temperature fractures, even at the most extreme high-temperature pre-strain, were partly trans crystalline and partly intercrystalline. In the case of a brass, these fractures were completely intercrystalline. According to the data on the percent of the grain boundary area that is cracked, at 22 pct high-temperature elongation, about 12.5 pct of the grain boundary area does not carry load. Thus, the inter-crack areas are carrying a stress that is about 11 pct higher than the nominal stress. A simple model predicts that the overall elongation, which is primarily the elongation in the bulk of the specimen, will correspond to the nominal stress when the stress in the intercrack area equals the tensile strength. Quantitatively this model predicts the equation The form of this equation will agree with that found if the strain-hardening exponent, n, equals unity. Actually this model is too gross an approximation to yield good quantitative results. The question naturally arises as to whether in ordinary hot-working, such as hot-rolling, intercrys-talline cracks are introduced that affect the low-temperature properties. It appears that the answer is that such a possibility cannot be overlooked, if the hot-working induces tensile stresses at temperatures above the equicohesive temperature and if the material tends to be notch sensitive at low temperature. ACKNOWLEDGMENT This research was supported by the Aeronautical Research Laboratory, Directorate of Research, Wright Air Development Center, United States Air Force. REFERENCES lC. Zener: Fracturing of Metals, 1948, Cleveland, ASM. 'H. C. Chang and N. J. Grant: Mechanism of Intercrystalline Fracture. AIME Trans., 1956, voL 8, p. 544; lownal of Metals, May, 1956. 'E. S. Machlin. CreepRupt ure by Vacancy Condensation, AIME Trans., 1956, vol. 8, p. 106; lownd of Metals, February, 1956 'C. Chen and E. S. Machlin: On a Mechanism of High-Temper at ure Inter-crystalline Cracking, lownd of Metals, July. 1957. p. 829. Alloys lent oxidation resistance. Binary alloys of aluminum in iron are ferritic and consequently have poor hot strength. Alloys of iron-aluminum-manganese were made in an attempt to produce an austenitic alloy containing sufficient aluminum to retain the oxidation resistance of binary alloys of iron-alumi-

Jan 1, 1960

By W. A. White

UNDERCLAY squeeze is the plastic flowing of underclay below coal pillars into mined-out entries and rooms. Squeezes may be caused either by wet mine conditions where the moisture is taken up by the clay—making it more plastic—or by the presence of certain clay minerals, such as mont-morillonite, which are plastic when there is enough natural moisture. Under either condition, sufficient stress will cause the underclay to flow. Squeezes may fill an entry or room within several hours, or it may be several months before movement stops. Squeeze areas commonly cover hundreds or thousands of square yards. The Coal Div. of the Illinois State Geological Survey has collected samples of underclays from various mines and from cores drilled by coal companies in the state. From these samples natural moisture content, particle size and particle size distribution, and clay mineralogy are determined. Data from samples collected from the underclay below Herrin (No. 6) coal in the Lumaghi Coal Co. mine near Collinsville, Ill., are used in this report to clarify points in the discussion. Data from samples taken from other mines lead to the same conclusions. A generalized geological section for the area is given in Table I. The underclay below coal No. 6 ranges from a few inches to 3 or 4 ft thick. The upper 6 to 18 in. are noncalcareous; the lower part becomes more calcareous with depth. Limestone nodules become larger with depth, almost grading into the limestone below. In areas where the clay is nearly absent the limestone may thicken to take its place; thus they may complement each other in thickness. There are two types of squeeze areas in a mine. In one type up to 3 or 4 ft of underclay lie in what appears to be a depression in the limestone underneath. This is suggested by a rim surrounding the squeeze area where the underclay is thin and the limestone lies within a few inches of the coal. In the second type the underclay of the squeeze area is surrounded by underclay of similar thicknesses which does not squeeze. Test Methods: Natural moisture content, particle size and particle size distribution, and clay mineralogy were determined by the following methods: Natural moisture is the moisture content a clay contains in its natural environment, expressed in percentage of the weight of ovendried clay (110°C or 230°F). To obtain the natural moisture content, given in Table 11, the clay samples were sealed in containers as soon as the samples were taken in the mines. Particle size and particle size distribution were determined by the pipette method,' and the data were plotted as cumulative curves, Fig. 1, on semi-logarithmic paper. Particle size was plotted on the logarithmic scale and percentage on the arithmetic scale. The quartiles (diameters that correspond to frequencies of 25 and 75 pct) and medians (diameters that correspond to the frequency of 50 pct) of the samples were determined from these curves. The clay minerals were identified from the data obtained by differential thermal' and X-ray powder" techniques. The differential thermal analyses were made on the whole samples, whereas the X-ray analyses were made on fractions of less than 2p. Data and Discussion Moisture Content: After the sealed jars had stood for 24 hr, those that contained squeeze samples had perspired, so that droplets of water had accumulated on the insides of the jars. Table II shows the moisture in the clay after it had perspired for 24 hr. (This perspiring was not noted in samples from nonsqueeze areas.) After perspiration one of the squeeze samples still had a higher moisture content than the samples that did not squeeze. Clay Mineralogy: The thermal analysis, Figs. 2 and 3, indicates that the clay minerals are chiefly micaceous in type; the low-temperature endothermal

Jan 1, 1957

By R. G. Grieves, G. Thodos

A method is presented for the accurate calculation of the cricondentherm and cricondenbar pressures of multicomponent hydrocarbon mixtures of known composition. The mixtures may contain six and quite possibly any number of components including paraffins, isoparaffins, olefins, acetylenes, naphthenes and aromatics. The approach is similur to that used for calculating critical pressures and cricondentherm and cricondenbar temperatures. The critical pressure, the normal boiling point and the approximate vapor pressure behavior of each component are all that art required. A stepwise culculation procedure is necessary for mixtures containing more than two components. From an analysis of 22 binary systems and 118 mixtures, the average deviation of calculated cricondentherm pressures from reported values is 2.4 per cent. For nine multicomponent mixtures the average deviation is 1 per cent. Considering 19 binary systems and 108 mixtures, the average deviation of calculated cricondenbar pressures from reported values is 1.7 per cent. For 15 multi-component mixtures, the average deviation is 2.2 per cent. INTRODUCTION A knowledge of the phase behavior in the critical region of multicomponent hydrocarbon mixtures is of value both in industrial processing operations and for the optimum operation of gas condensate reservoirs. Accurate methods of calculating the critical temperatures and critical pressures4,6,7,8,9,23 and cricondentherm and cricondenbar temperatures6p10 of multicomponent hydrocarbon mixtures are available in the literature. If the cricondentherm and cricondenbar pressures could be calculated with equal accuracy, the entire phase diagram of a multicomponent hydrocarbon mixture could be well approximated. The work of Etter and Kay6 is limited to systems containing the normal paraffins and has not been tested on systems containing a heavier component than heptane. In addition, the development of their multicomponent equations is based upon a limited number of mixtures containing from three to six components. Silverman and Thodos have considered systems containing both paraffinic and non-paraffinic hydrocarbons, but their correlation is limited to binary systems and is highly inaccurate for methane systems. Eilerts has done extensive work on the cricondenbar pressure; he has produced an excellent correlation for binary systems. However, his procedure for multicomponent mixtures is chiefly useful for highly complex mixtures requiring a knowledge of the vapor-liquid equilibrium behavior of the mixtures; he has not considered the cricondentherm pressure. The objective of this study was the development of an accurate and rapid method for the calculation of the cricondentherm and cricondenbar pressures of multicomponent mixtures containing all types of hydrocarbons and having a wide volatility range. The approach that was adopted is similar to that used by Grieves and Thodos for cricondentherm and cricondenbar temperaturesl0 and for critical pressures.9 However, methane systems had to be considered separately and a modified stepwise calculation procedure was utilized for the cricondertherm pressure. The correlations were developed in a manner similar to those for critical pressures and cricondentherm and cricondenbar temperatures. Based upon binary data reported in the literature it was observed that the ratios of cricondentherm and cricondenbar pressure to the pseudocritical pressure (molar average), pt/ppc and pp/ppc, respectively, in two-component systems depended upon the mole fraction of the low-boiling component and upon the diversity in properties of the two components. A dimensionless boiling-point parameter Tb,/Tb was chosen to represent the diversity in properties of the components. For a binary system, Ti,'is the molar average of the normal boiling points of the two components involved. For a multicomponent system it is either the molar average of the normal boiling points of all of the components involved or the molar average of the normal boiling point of the pure low-boiling component and of the atmospheric boiling point of the low-boiling-free mixture of

Jan 1, 1965

By R. M. Rose, D. P. Ferriss, J. Wulff

Single crystals of tantalum, tungsten, and the binary alloys thereof were grown by electron-beam zone melting and tested in tension between 77° and 373°K. The ductile-to-brittle transition temperature increased sharply with solute concentration, for both tungsten-rich and tantalum-rich alloys; apparently, the maximum transition temperature exists near the 50 pet concentration. Twinning was observed to be a consequence of cleavage-crack propagation. Cleavage occurred on(100)planes, and extensive tearing and "river markings" were present. The onset of brittleness could not be associated with any change in deformation mode, the yield point phenomenon, or the large rise in yield stress with decreasing temperature. Cleavage was observed to initiate at either the specimen surface, or subgrain boundaries. The observation was made that the grain boundaries of Polycrystalline materials are probably even better as nucleation sites for fracture, and are responsible for brittleness at high temperatures and lower solute concentrations than those of the corresponding single crystals. TUNGSTEN and tantalum, the two high-melting neighbors in the third transition period of the periodic table, present striking contrasts. Although both are bee, tungsten has far higher elastic moduli, and the highest ductile-to-brittle transition (DBT) of all the pure metals.' Tantalum, however, is ductile at liquid helium temperatures. Large strain aging and yield point phenomena are observed in tantalum,2,3 but only to a lesser extent in tungsten.4 Tungsten work-hardens at a high rate,5 whereas this effect is negligible in tantalum.' Since the mutual solid solubility of these two metals is complete,7 and no ordering has yet been reported in the binary system, the possibility of depressing tungsten's DBT by tantalum additions was considered. Also, tungsten additions to tantalum could produce hard, high-melting alloys which might be ductile at room temperature. Such alloys offered excellent bases for complex alloy development, particularly with regard to the effect of rhenium on Group VI metals.8"10 In addition, there was the opportunity to examine flow and fracture modes in the vicinity of the DBT, with particular emphasis on the correlation between brittleness and fundamental deformation mechanisms. Myers11 has reported that recrystallized alloys with up to 10 pet W in tantalum are ductile at room temperature, but alloys with 20 pct W could not be swaged at temperatures as high as 500°C. The whole spectrum of Ta-W alloys has been surveyed by Braun, Sedlatschek, and Kiefferl2 using sintered powder compacts. In addition to some physical properties they reported a maximum hardness at about 50 at. pet W, dropping to much lower hardness levels for the pure components. They were able to cold work tantalum-base alloys with as much as 30 pet W and to warm work tungsten-base alloys with up to 20 pet Ta by procedures similar to those used for pure tungsten. EXPERIMENTAL In order to study deformation modes and to keep the impurity concentrations at a minimum, electron-beam zone melting was used to prepare single crystals of high purity. The electron-beam zone melting apparatus is similar to that described by Calverley, Davis, and ever" and incorporates a grid control rectifier to maintain control of emission current. Pure metals were refined by making three zone passes at 4 mm per min up the rod. Alloys were prepared by melting together wire of one constituent on a previously melted rod of the major constituent. Subsequently, two zone passes were made in opposite directions to level the composition after the manner suggested by pfann.14 Purification of the starting materials was accomplished by evaporation of the several impurities, and the degree to which this was accomplished is indicated in the chemical analyses of Table I. The uniformity of composition along a zone levelled rod was within the i 1 pet accuracy of the fluorescent X-ray technique used to determine composition. Crystallographic orientation of the

Jan 1, 1962

By Stephen Zorn

INTRODUCTION The process of financing mining projects in developing countries has changed greatly in the past 15 years. New methods of financing, notably the use of syndicated Eurocurrency project loans, have appeared, and direct equity financing by transnational mining corporations has become less significant. These changes are of particular importance to developing countries which have many mineral deposits still awaiting development, or even discovery. If major new mines are to be financed, host governments will need to obtain more sophisticated information than has hitherto been widely available as to the various sources of finance currently available and as to possibilities for innovative approaches to financing, such as the combination of several different kinds of financing in a single package. This paper reviews the major sources of mining finance potentially available to developing countries and highlights those problems in obtaining adequate financing that developing country producers have begun to experience in the last few years and that are likely to persist through the 1980s. Section I surveys the major types of mining finance; section II reviews specific financing problems, including (a) the withdrawal of the transnational corporations from developing countries, (b) inflation and the size of new projects; (c) developing country indebtedness, and (d) competition among projects in different countries. SOURCES OF DEVELOPING COUNTRY MINING CAPITAL1/ There is a wide range of financing mechanisms which are potentially available to developing countries with economically viable mining projects., Moreover, these financing mechanisms have not been fully exploited by developing countries, and more aggressive pursuit of financing by the governments of these countries may well reveal greater possibilities in respect of any particular project than may initially have appeared. However, virtually all the funds available from these sources are available only to projects which meet the standards of viability acceptable to lenders and others in the business community. If a project does not, for example, promise to generate a discounted cash flow rate of return of at least 15 per cent on total funds employed, or if it does not appear likely to generate sufficient cash flow in the early years of production to cover debt service requirements with a comfortable margin in reserve, most of the sources of financing will not be available. Only where a government has its own financial surplus (as in the case, for example, of the industrialization program of the Saudi Arabian government) can it effectively undertake projects which do not satisfy the definition of economic viability that is accepted at any given time by the worldwide financial community. Internal Sources In Developing Countries Internal financing capacity in developing countries is restricted to a relatively small number of countries - typically those large enough to support a well-rounded industrial sector, in which mining is only one of a number of dynamic industries. While there are large mining companies in certain other countries, the ability of such companies to finance new projects (or even, in some cases, to generate the cash necessary to maintain existing levels of production) is highly problematical. Within developing countries, the possible sources of internally-generated mining finance are the following: (1) state-owned enterprises; (2) private capital; (3) the banking system, and in particular those financing agencies that have a special involvement with the mining sector; and (4) direct budgetary appropriations.

Jan 1, 1985

By H. Kurushima, S. Tsunoda

An investigation of the hydrometallurgy of Cu-Zn concentrates by The Dowa Mining Co. of Japan is described and a detailed flowsheet of the Kosaka hydro-metallurgical plant is given. Sufficient operating experience has shown that the Dorrco FluoSolids system has proven successful for recovery of both zinc and copper by roasting in a fluidized bed. At present, 2400 metric tons of concentrates per month are being treated and recoveries of 93 pct Cu and 65 pct Zn are being effected. A SURVEY of the Japanese chemical industry in 1949 revealed, among other things, that sulphur-bearing blast furnace gas from the Kosaka smelter of The Dowa Mining Co. Ltd., Kosaka, Japan, was being exhausted to the atmosphere as waste. In addition, it was costing that company an average of ten million yen ($28,000) annually for damages to the surrounding property caused by the sulphur dioxide in the gas. It was recommended by this survey that the gas be utilized for the production of sulphuric acid by the contact process. Mr. Kurushima visited the United States in May 1950 to investigate the engineering, construction, and operation of a contact acid plant. Any acid produced at Kosaka would necessarily have to be 98 pct H,SO, to prevent corrosion in railroad tank cars transporting it to the point of use. However, the production of 98 pct acid requires constant volume and SO, content of the gas. As the converter gas at Kosaka fluctuates in both volume and quality, it was decided to evaluate the smelting process with relation to other methods of recovery. This evaluation revealed a relatively new type of roaster, the Dorrco FluoSolids reactor, which was reported to be capable of roasting the copper sulphide concentrate in an excess of air with the production of an SO1 gas strong enough for acid production and a water-soluble copper sulphate calcine. The copper sulphate then could be leached from the roasted ore and electrolytic copper recovered from the leach solution in much the same manner as practiced by the Chile Exploration CO. for treating naturally occuring copper sulphate ores. Use of a reactor of this type would eliminate the need for a blast furnace and converter and, in addition, would effect savings in labor and fuel. The Kosaka ore is a microscopically fine mixture of copper, zinc, and lead sulphides. The lead and a small amount of the barite present can be separated by flotation, but any separation of copper and zinc proved extremely difficult. In blast furnace operation at Kosaka, zinc had been slagged off until a stockpile of about 12,000,000 tons containing 5 pct Zn had been accumulated. Mr. Kurushima felt that if any of the zinc in the concentrate was sulphat-ized and leached with the copper, it also could be recovered electrolytically. The Dorr Co., sponsors of fluidization technique in the metallurgical field, suggested that sulphate roasting be tested out on a laboratory scale and that, if successful, a commercial Dorrco FluoSolids system be constructed. They indicated that the results from such laboratory tests could be transposed to a commercial scale without pilot planting the roasting operation. It was therefore decided to send samples of flotation concentrate to the West-port Mill, laboratories of The Dorr Co., for testing. The objective of Mr. Kurushima's visit to the United States thus had changed from investigation of sulphuric acid plants to a fundamental examination of the hydrometallurgy of copper and zinc. Testing Program In February 1951, Mr. Tsunoda went to the United States to witness the application of the FluoSolids system to sulphate roasting at The Dorr

Jan 1, 1956

By R. D. Satterley

THE Sherwood mine is an iron-ore mine owned and operated by the Inland Steel Co. in the Iron River district of the Menominee Range in Michigan. The property consists of an 80-acre tract in the village of Mineral Hills, about a mile north of the city of Iron River. The ore mined is a reddish brown, nonbessemer hematite and limonite. The ore bodies lie in a large syncline having an east-west strike and are associated with a rock structure that is folded in a complex manner. The two 40-acre tracts run north and south and the shaft is at about the center of the north forty. The shaft is 1286 ft. deep, with the principal operating level at a depth of 1000 ft. from surface. A new level at a depth of 1200 ft. is in process of development. The ore body at the 1000 ft. level is east and west at approximately the line between the north and south forties and at this elevation is from 50 to 250 ft. wide and extends above the level at varying heights of from 50 to 250 feet. The 1000-ft. haulage drift extends south from the shaft, through the east-west ore body to the slates on the south side of the body. The ore body was intercepted in the drifting at about 800 ft. from the shaft and was about 200 ft. wide at that point. A crosscut was extended to the east and west property lines along the south boundary of the ore body. This east-west ore body is laid out in areas 80 ft. wide for stoping with pillars 40 ft. wide. With this plan a stope is approximately 80 by 200 ft. and has a pillar on both sides that is approximately 40 by 200 ft. The ore has a height of from 50 to 250 ft. above the elevation of the level, therefore the height of the stopes varies in accordance with the height of the ore body at each location. From the crosscut, two main raises, each 6 by 7 ft., are put up into each 80 ft. stope area (Fig. I). One of the main raises serves as a manway and the other as an ore raise, through which the ore is transferred from the stope to the tramming equipment. The original layout was for scraping of the ore from under the stopes into the ore raises. The ore raise is put halfway (east and west) along the 80-ft. stope area and usually is in iron formation. The manway and ore raise are on approximately 15-ft- centers. These main raises are put up to a height of from 22 to 30 ft. above the level floor, then from the top of the ore raise a scraper drift (8 X 8 ft.) is driven across the width of the ore body, which is in the neighborhood of 200 ft. From the scraper drift, mill raises are put up at 12 ½ -ft. centers, staggered on opposite sides of the drift, and these are extended 23 ft. above the elevation of the scraper-drift floor. The sublevel connecting the top of these mill raises is called a mill "sub." Other sublevels are developed parallel to the scraper and mill subs at 25-ft. vertical intervals above the mill sub. The mill sub and the other subs above the mill sub are known as sublevels or dog drifts, and are 4 ft. wide and 6 ft. high. These dog drifts

Jan 1, 1945

By Arnulf Muan, R. W. Taylor

Activities of iron in Fe-Pt alloys have been dctermined by equilibrating mixtures of platinum metal and iron oxide at known oxygen Pressures in a thermobalance at 1300°C. Conzpositions and iron activities of the oxide phase at equilibrium are known from previous work, and compositions of the Fe-Pt alloy phase formed at equilibrium were detcvt?zined from the observed weight changes of the samples. The activity curve obtained shows a strow negative deviation from Raoult's law. THE present investigation was undertaken as part of a research program dealing with phase equilibrium relations existing among the oxides of iron and titanium at 1300°C. At low oxygen pressures of the gas phase in equilibrium with these oxides, the iron activity of the system is high, and considerable alloying of iron with the platinum used as a container material takes place. Thermodynamic data for Fe-Pt alloys at 1300°C are needed in order to evaluate quantitatively the extent of such reactions. Larson and chipmanlhave determined activities of iron in Fe-Pt alloys at 1550°C by equilibrating platinum metal with CaO-iron oxide-SiOzmelts in which the iron activities were known. Compositions of the resulting Fe-Pt alloys were determined by chemical analysis. Mundiath and Gerassimov2 have studied thermodynamic properties of Fe-Pt alloys by electromotive force measurements in the temperature range 550" to 1000°C. The experimental method used in the present investigation is a slight modification of that used by Grube and Ratsch3 in studies of NiCr-alloys. 1) EXPERIMENTAL METHOD 1) General. Mixtures of platinum metal and iron oxide were equilibrated at 1300°C in atmospheres of known oxygzn przssures, and the course of the reactions was followed by measuring the weight changes of the mixtures. The principles involved in the derivation of composition-activity relations from these measurements are illustrated by the composition triangle for the system Fe-FeZO3-Pt shown in Fig. 1. Take as an example a mixture of FeZO3 (hematite) and platinum such that the total composition is represented by point T. If this mixture is heated to 1300c in air (poz = 0.21 atm) and the oxygen pressure is then reduced gradually, the oxygen content of the oxide phase decreases and increasing amounts of iron enter the metal phase. As the oxide phase and the metal phase for all practical purposes are insoluble in each other, their compositions are represented by points moving toward Fe along the joins Fe-Fe,03 and Fe-Pt, respectively. The total composition of the mixture during this process also changes, but only with respect to oxygen content, because the vapor pressures of iron and platinum are negligible at 1300°C. Hence the change in total composition is described by a straight line (constant Fe/Pt ratio) radiating from the 0 apex of the composition triangle Fe-Pt-0, of which the triangle in Fig. 1 is a part. Only one such line ("oxygen reaction line", T-T",) is shown in Fig. 1. The total composition of the alloy-iron oxide mixture at any instant must, in addition, be located on the straight line (conjugation line) connecting the two points representing the compositions of the two coexisting phases. It therefore follows that the total composition of the mixture at any instant is represented by the point of intersection between the conjugation line and the oxygen reaction line. An example of the situation prevailing at a chosen oxygen pressure, po2, is shown in Fig. 1 by points a' (alloy composition), b' (oxide composition) and T' (total composition). Point b' is known from the work of Darken and Gurry,4 and point T' is experimentally determined by the observed weight change of the mixture (distance T-T). Hence, point a', the composition of the alloy, is determined from the above data as the intersection between the join Pt-Fe and the extension of the straight line bl-7'. The activity of iron in the alloy at equilibrium is identical to that of the iron oxide phase, if the same

Jan 1, 1962

By Donald Jaffe, Michael B. Bever

The solidification of Al-Zn alloys (2 to 70 pct Zn was investigated at different rates of solidification. The resulting structures were studied; the amounts of nonequilibrium eutectic were measured and compared with the amounts calculated on the assumption of no diffusion in the solid. The compositions of the cored primary constituent were investigated by quantitative autoradiography after activation of the zinc by neutron irradiation. These compositions were also determined from microhardness values. IN a recent investigation of the soltdification of aluminum-rich AI-Cu alloys,' the amounts of non-equilibrium eutectic were measured and compared with the amounts calculated on the assumption of no diffusion in the solid. The compositions of the cored primary constituent were investigated by quantitative autoradiography. The work reported here extends the investigation of nonequilibrium solidification to the Al-Zn system in the range from 2 to 70 pct Zn. In addition to autoradiography, microhard-ness values were used to determine compositions on a micro scale. Solidification Experiments The alloys contained approximately 2. 6, 12, 20, 30, 50, and 70 wt pct Zn and the balance aluminum. According to published diagrams the eutectic reaction occurs at 382°C between the eutectic liquid (95 pct Zn), a (82.8 pet Zn), and $ 498.9 pct Zn). Solid-state reactions at lower temperatures (due to the miscibility gap between 350" and 275"C, the eutectoid at 275'C, and the precipitation from supcrsaturated a) did not affect this investigation. Even if they occurred to any appreciable extent, they did not alter the evidence pertaining to the solidification structures. The alloys had to be of high purity to avoid radioact~ve contamination during activation. The aluminum analyzed 0.015 pct Si, 0.009 pct Fe, less than 0.004 pct Cu, and less than 0.006 pct Mg with traces of sodium and titanium; the zinc was reported to be at least 99.99 pct pure with traces of iron and magnesium. The alloys were prepared under argon in an induction-heated, bottom-pouring furnace, and poured into a coated steel mold, which could be preheated to temperatures up to 700°C in order to control the rate of solidification. The pouring temperatures ranged from about 40" above the liquidus for 2 pct Zn alloys to about 130°C above the liquidus for 70 pct Zn alloys. As soon as the melt entered the mold, the readings of a thermocouple placed % in. above the bottom of the mold were recorded by a recording potentiometer. Cooling at the rate induced by the initial temperature of the mold was continued to a temperature 100°C below the liquidus; the mold with its contents was then quenched in icy brine. Quenching from a fixed interval below the liquidus was used to provide a standardized procedure, since the solidus and liquidus temperatures and the interval between them vary greatly over the composition range investigated. The temperatures from which the samples were quenched were below the equilibrium solidus, but under nonequilibrium conditions some liquid was still present. This residual liquid solidified during the quench. The samples measured 314 in. diam and 11, in. height. Drillings for chemical analysis were taken

Jan 1, 1957

By J. J. Scott

This investigation utilizes three dimensional photo-elastic techniques to determine the stress distributions in the pillars and the roof of a room and pillar mine model. Castolite plastic was used for the construction of the model in which a stress pattern was developed by the stress freezing process. Analysis of the stress pattern was accomplished by observation of points in slices from the model with a polariscope and solving the data thus obtained by the shear-difference method. Slices through the centerline, edge of pillar and centerline of span were investigated. The results of this work provide information on the overall stress distribution in points of stress concentration in compression, shear and tension, show relative magnitude of stress throughout the model and indicate directions of the most important stress values. A generalized roof bolt pattern is developed for room and pillar mines based on the stress distribution. A digital computer was used in the reduction of data and proved to be extremely useful for investigation of this type. Underground excavations disturb the equilibrium of the earth's crust and a core of fracture, or altered stress distributions exists around the openings. This fact is well known by mining operators and investigators in the rock mechanics field. Analysis of the stress distribution in the areas around mine workings is a most difficult problem and one which has no simple and direct solution. Some of the approaches used by investigators in attempts to study stress distribution around mine openings involve mathematical analysis, photoelastic techniques, statistical analysis, model studies on brittle materials and observation of fracture patterns. Models involving imbedded strain gauges, gelatin models using imbedded strings to show internal movement, and many other unique laboratory techniques are employed. Work is also being done in mining operations where load cells, strain gauges, photostress material, convergence plugs, dynamic plugs, etc., are used to measure strain which can in turn be used to obtain stress. Some of these devices measure strain from which stress may be derived. All approaches to the solution of stress distribution are hampered by the fact that the earth is not a homogeneous, isotropic and elastic media. Geologic faults, fractures, bedding planes, vugs, variations in material composition, variations in grain size and structure, etc., make it extremely difficult to obtain results which can be universally applied to mining operations. The purpose of this investigation will be to demonstrate the use of three-dimensional photoelastic techniques to obtain the stress distribution in the pillars and roof of a room and pillar mining operation. This method utilizes full analysis of interior points, and thus it may be that small tensile or shear stresses found in the investigation will prove to be of greater significance than the more obvious points of stress concentration found by two-dimensional techniques. A digital computer was employed to simplify and to shorten the time necessary to obtain final results. Application of the computer to problems of this type may enable future investigators to attempt more elaborate analyses than have been previously considered feasible. THEORY Three Dimensional Stress Analysis-Shear Difference Solution:' Photoelastic studies are based on the fact that an optically isotropic transparent solid becomes optically anisotropic when subjected to forced deformation; the degree of optical anisotropy being proportional to the deformation of the material. There are two fundamental laws which govern photoelasticity: 1) Light is polarized in the directions of the principal stress axes, and is transmitted only on planes of principal stress. 2) The difference in principal stresses is proportional to the difference in the indices of refraction along the planes of principal stress. One method used in three-dimensional photoelastic work is to examine a slice of the object by normal incidence and oblique incidence. In normal incidence,

Jan 1, 1964

By F. Garofalo

It has been shown by various investigators that during constant stress creep the dependence of minimum creep rate, 6,, on stress, o, is given by em = A onat low stress levels, md by 6, = A' exp [ß s] at high stress levels. In these relations A, n, A', and ß are constant at constant temperature. A single relation has been found which satisfies conditions for both high and low stresses and agrees well with experimental results. This relation is 2, = AN (sinh a s)n, where A" is a constant at constunt temperature and a = p/n. This relation also satisfies the linear relation, 6, = k s, found at temperatures near the melting point at low stresses. EXPERIMENTAL creep results have led to a number of empirical relationships between minimum creep rate, 6,, and the applied stress, s. Under conditions of constant stress it is generally found that at low-stress levels,'-' the dependence of minimum creep rate is given by 6, = Asn. At high-stress levels'74 the experimental results fit the relation, 6, = A' exp [po l. In these relations A, n, A' and ß are constant at constant temperature. A model based on climb-of-edge dislocations from a pile-up array leads to a relation similar to that found experimentally at low stresses.' On the other hand. theories based on chemical-reaction rate,5 nonconservatively moving dislocation jogs, and jog migration and climb-of-edge dislocations4 lead to a relation similar to that found experimentally at high stresses. No difference in mechanism between low and high stress levels has been clearly defined; it is questionable whether such a difference really exists. In any event, the major argument usually given in substantiation of a change in mechanism from low to high stresses is that no single relation exists for defining the stress dependence of the creep rate over wide ranges in stress. However, such a relation has been found and is of the form, dm = A" (sinh a s)n, where A" is a constant at con- stant temperature and a = ß/n. This relation agrees well with experimental results over wide ranges in stress and temperature for copper, aluminum, an A1-3.1 pct Mg alloy, and an austenitic stainless steel. STRESS DEPENDENCE OF MINIMUM CREEP RATE At low stress levels the minimum creep rate, gm, depends on the stress, 0, under conditions of constant stress creep through the relation em=Aon [1] The quantities A and n have been defined previously. In the range in which this relation applies, a linear dependence is found in a log em,-log o plot. Above the stress range of application of relation [I], the minimum creep rate increases much mar; rapidly than predicted by relation [I]. This behavior is shown in Fig. 1 for a series of creep tests on copper4 at various temperatures ranging from 673 o to 973°K. Relation [I] is satisfied at the lower stresses, although the results at 973°K are quite limited. In all cases the transition beyond the applicable range of relation [I] is a gradual one indicating no abrupt change in mechanism. For all test temperatures, values of n have been determined from the results in Fig. 1. These are reported in Table I under Alog tm/hlog o. At high stress levels the stress dependence of minimum creep rate under conditions of constant stress is given by im = A' exp [ß a] 2] All factors have been defined previously. In a log em-0 plot, relation [2] predicts a linear function. Experimentally, a pronounced deviation from the prediction of relation [2] is found at lower stresses. As the stress is lowered, the minimum creep rate decreases more rapidly than predicted by relation [2]. This shown for copper in Fig. 2. Again it is found that the transition from high to low stresses is gradual and no really sharp change is found. Values of p determined from the high stress results are given in Table I. The dependence of minimum creep rate on stress at constant temperature for all ranges in stress

Jan 1, 1963

By J. Lemish

Considerable research has been conducted in Iowa in recent years on carbonate aggregate reactions in concrete. Groups outside the state have become active in the past few years after recognizing that certain carbonate aggregates are reactive in concrete. The paper reviews the nature and extent of the problem and a summary is given of research by the author and his associates. In recent years considerable research has been conducted in Iowa on carbonate aggregate reactions in concrete. The research is part of a general study on the behavior of carbonate rocks as concrete aggregates sponsored by the Iowa State Highway Commission. Research on carbonate aggregates has not been extensive in the past. Laughlin1 published one of the first papers on carbonate aggregates in 1928 and was followed by others, notably H. S. sweet,' B. Mather et al.,3 and K. Mather4 who emphasized the petrographic and physical aspects of carbonate aggregates. The recognition that certain carbonate aggregates are reactive in concrete has led to increased participation in research in the past few years by groups outside of Iowa. Significant contributions have been made by Swenson and Gillot,5 Hadley,6 and Chaiken and Halstead7 in work which emphasizes the expansion of carbonate rocks in alkaline environments and the reaction of carbonate minerals or dedolomitization with alkalies. It is the purpose of this paper to review briefly the nature and extent of the problem and present a summary of the research by the author and his associates. EXTENT AND NATURE OF THE PROBLEM The problem is the deleterious behavior of certain carbonate aggregates in concrete. It was first recognized in Iowa over 20 years ago when poor service records of certain highways were correlated with aggregates produced from the Glory and LeGrand quarries. Deleterious behavior of carbonate aggregates have been reported in Canada and, more recently, in New York and Virginia. As more knowledge is gained concerning the problem, distress in concrete related to carbonate aggregates may be recognized over a widespread area. The problem may potentially exist in the Midwest, the Northeast, and other parts of the country underlain by thick sections of carbonate rocks readily available for utilization as aggregates. The nature of distress in Iowa highways is a general weakening and deterioration of concrete characterized by progressive cracking and spalling away from joints and edges (Fig. 1). The distress generally occurs after 15 years of service and becomes progressively worse. Specimens of such concrete lack the toughness of sound concrete and break easily under the hammer in the manner of a soft brick. The matrix is generally highly carbonated and dark borders, or reaction shells or rims outline the argillaceous carbonate aggregate fragments (Fig. 2). Cracks observed in cores cut across the aggregates and concrete matrix. Although localized volume change (expansion) is associated with spalling, there is no definite field evidence in Iowa that excessive growth of concrete slabs has occurred. The experience with carbonate aggregates in Iowa indicates that the concrete deterioration is not the same as that induced by the alkali-aggregate reaction associated with siliceous aggregates. The principal difference is that in Iowa the distressed concrete is weakened throughout the slab. In concrete affected by the alkali aggregate reaction, the

Jan 1, 1961

By M. E. Wadswort, A. S. Peck

Infrared data disclose that phenacite reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. The absorption band characteristic of the antisymmetrical C = 0 oleate structure appears at a spectral wavelength of 1623 cm-'. Chemisorption also results in the displacement of OH- and silicate from the mineral surface. Infrared absorbance at 1623 cm-1 is correlated with float-ability at different pH for -60-mesh phenacite particles. Phenacite, Be2SiO4, is an ore mineral often associated with quartz, microcline, and chrysoberyl in pegmatites and mica schist. Experimental phenacite beneficiating processes have been confined principally to the flotation of low grade ores occur-ing in several mountain ranges of Utah and Nevada. The U.S. Bureau of Mines ' has recently reported on the separation of phenacite from ore deposits of Mount Wheeler, Nev. Infrared techniques were previously applied by the authors to characterize the role of sodium oleate and oleic acid in the flotation of several non-sulfide minerals.23 A parallel study was projected to the flotation of the orthosilicate mineral phenacite with oleic acid. Infrared spectra provided a 'molecular fingerprint' of the mineral surface and permitted identification of the reaction mechanisms. Infrared data were complemented with flotation and chemical tests. EXPERIMENTAL PROCEDURES The experimental procedures used in this investigation, for which data are presented in graphical or spectral form, are described in chronological test order. Phenacite crystals from Mt. Antero, Colo., were obtained from Ward's Co., Monterey, Calif. The crystals were fragmented in a porcelain mortar to -60 mesh and then pretreated with 0.5 molar HC1 for 15 min to remove iron. Then, the mineral particles were washed free of acid with distilled water and dried. Part of the dried material was ground to a fine powder with a Fisher Grinder using an agate mortar and pestle. Next, the powder was placed in a graduated cylinder and mixed with 500 ml of distilled water. The mineral in suspension was decanted from the settled fraction after 5 min, and the colloidal suspension was used for adsorption tests in which a high specific mineral surface area was required for adsorption and infrared analysis. Conditioning was performed in 50 ml glass centrifuge tubes for both infrared and flotation test determinations. Twenty ml of colloidal suspension was used for the infrared adsorption tests. One and a half g of deslimed -60-mesh HCl pretreated phenacite was added to 20 ml of distilled water for flotation conditioning tests. Six mg of oleic acid was used for each infrared adsorption test, and 0.2 mg of oleic acid was used for the flotation conditioning tests. HCl and NaOH were used for pH modification. The pulps were stirred at a speed of about 1500 rpm for 3 min. Then, the solids were separated out and either dried at 50°C or immediately transferred to a float cell. The pH of the residual liquid was determined with a Beckman Zeromatic pH meter. The flotation procedure is described as follows: 1) A 325-1111 glass micro-float cell was filled with distilled water. 2) Conditioned mineral was placed in the cell and the pulp was aerated through the glass fritted bottom at 7 psi pressure. 3) Floated mineral was skimmed from the cell with a glass slide until flotation ceased. (The end point was reached in all tests in less than 2 min.) 4) The flotation products were dried, weighed, and the recovery was calculated. Samples for infrared analysis were made into mulls using either oleic acid or series 13-21 Halocarbon oil obtained from Halocarbon Products Corp., Hacken-sack, N.J. The mulls were placed between two sodium chloride windows. A characteristic phenacite infrared band at 1868 cm-' was used as an internal standard for quantitative determinations in which absorbance at this position was quantified by the baseline-tangent method4 and related to absorbance at 1623 cm-'. The ratio obtained by dividing absorbance at 1623 cm-' by absorbance at 1868 cm-' was defined as an absorbance quotient for use in graphical presentation.

Jan 1, 1968

By Thomas S. West

A gravel pack completion is described which, in addition to sand screening, permits the exclusion of water and gas from the oil production. A gravel pack composed of alternate layers of different particle sizes is employed which has horizontal but not overall vertical permeability to drilling mud. A packer is run on the tubing and set in the screen member, around which the gravel layers are placed. The hydrostatic pressure of a mud column prevents the entry of fluid above (or below) the level of the packer. The producing level may be changed by raising or lowering the tubing. Vertical coning is controlled by replacing the mud column with oil and continually injecting oil into the sand section above (or below) the packer. Three well histories with this completion are described in detail. Statistics on the first 100 completions of this general type are given. INTRODUCTION Gravel pack type completions have heretofore been almost exclusively for the purpose of preventing sand production. This paper describes and presents well data on a gravel pack procedure which is primarily a selective completion method. Although complete sand screening is achieved, the exclusion of gas and water is the primary objective. The application of this procedure is therefore not limited to unconsolidated sands. Application to hard sand or limestone reservoirs is equally feasible. GRAVEL PACK PROCEDURE Figs. 1 and 2 illustrate the gravel pack procedure employed. The gravel is placed by means of the frangible disc type dump bailer shown by Fig. 1.' This bailer has its lower end closed by a plate glass or steel rimmed cement disc. This disc breaks when the bailer passes over the liner allowing the gravel to be deposited around the liner. The liner employed is usually 2 3/8 in. to 2 7/8 in. OD and 1.995 in. or 2.07 in. ID (ID of 2-in. tubing or 2-in. line pipe). Two tvDes,. of slotted sections have been employed. One type employs horizontal hacksaw cut or milled slots of about 1/32 in. width opposite the producing section. The other type employs the same type,. of horizontal slot. but slots are placed in groups of six at intervals of about 8 in. A cage composed of half round vertical bars, spaced apart, is then welded to the pipe over the slotted sections. This liner has the bottom end closed, usually by bull plugging. The upper end is closed, while placing the gravel, by a cap which is held in place by means of a shear pin. This cap has a mandrel attached to it which extends downward inside of the liner to within a few inches of its lower end. The top of the liner cap is formed to fit a releasing type wire line core barrel overshot. The liner is lowered to bottom on the wire line by means of this overshot and released. The length of the liner is usually suffi- cient to extend to about 20 ft above the highest level to which gravel is to be placed, the upper end of the liner always being in the casing. The dimensions of the liner and bailer are such with respect to the casing size that the bailer will always pass over the liner. After releasing the liner the bailer is run to bottom. Passage of the empty

Jan 1, 1951

By H. W. Mead, C. E. Birchenall

SELF-DIFFUSION in pure gold has been studied by Sagrubsky,1 McKay,2 Gatos and coworkers,3,4 and Okkerse.5 Sagrubsky used a sectioning technique but reported results far lower than any of the others. The work seems to be carefully done, and it appears that a factor of 60 must have been omitted in his calculations or the units misstated by an equivalent amount. McKay used a surface activity method, and Gatos and Kurtz, following Gatos and Azzam, applied autoradiography to the measurement of activity on an oblique section through the diffusion zone. These two investigations agree well with each other but give results below those reported here. Okkerse employed a very careful sectioning technique. Chemical interdiffusion in Au-Ag alloys has been measured under several concentration conditions. Average values of the diffusion coefficient for the range of 0 to 18 atomic pct Au were obtained by Braune.6 since the diffusion coefficient probably varies markedly over this range, the values may not be too useful. Also, a plot of these data suggests that grain boundary contributions may have been appreciable at the lowest temperature employed. Ebert and Trommsdorf7 give average values for 0 to 9 atomic pct Ag, and Johnson8 reports average values for 45 to 55 atomic pct Au. Johnson also measured silver and gold self-diffusion coefficients in 49.2 atomic pct Au alloys, and self-diffusion in pure silver. The self-diffusion of gold in pure silver has been determined by Jaumot and Sawatsky.10 Other measurements which do not cover a range of temperature or are of low precision are not mentioned in this account since a review by Kubaschewski is available." This contribution reports diffusion coefficients for self-diffusion in gold, self-diffusion of gold in Au-Ag alloys, and chemical diffusion in Au-Ag alloys. Although it had been intended to obtain silver self-diffusion data in the alloys it now appears unlikely that these measurements can be done soon, so a table has been worked out for a self-consistent scheme of diffusion coefficients which should not be too far from the true values. Experimental Details Experiments on pure metals were conducted using fine gold of 99.99+ pct Au and silver of the same purity. Alloys were prepared by melting the two metals together in a graphite crucible in vacuo and allowing the slug to solidify in the crucible. After machining to a cylinder about 0.85 in. diam each slug formed one half of a diffusion couple. Compositions were determined later by analyzing chips taken from the extremities of the diffusion zones. The gold used in the preparation of alloys was sometimes pure gold but was normally either in the form of clean pickled alloy from previous experiments or gold recovered by oxalic acid precipitation from warm aqueous solution. Chips from the various stages of experimentation were dissolved in aqua regia and the solution taken to low bulk, diluted with water, and again taken to low bulk before diluting for the precipitation. This precipitated gold contained a small amount of silver as the only impurity detectable by spectrographic analysis. Disks for use in diffusion couples had opposite plane faces abraded on emery paper as far as zero grit, were annealed for 12 hr at 900°C in argon, and had one face of each disk polished to 000 emery paper. Radioactive gold was plated at about 2 ma per sq cm from a small volume of cyanide solution containing 1 mg of inactive gold as a carrier. Specimens , were freshly abraded on 4/0 emery paper immediately prior to plating. In the case of the active couples disks of a similarly prepared but unplated alloy or pure metal were placed on top and welded to the active disk. With the concentration couples disks of different compositions were welded. Welding was performed after a pressure of 5,000 lb had been applied at

Jan 1, 1958