Search Documents

By Hans Lundberg

IN ORDER to comprehend the help and information that may be expected from electrical prospecting, it is necessary to have at least a general knowledge of the methods and principles involved in preparing and interpreting results obtained in the field. Electrical prospecting is rather complicated, both in theory and practice, and in order to make a brief description clear to the practical mining man it has been necessary to idealize and generalize the problems, at the risk of having such simplification criticized by the theoretical man. This simplification must not be misinterpreted as showing a lack of theoretical knowledge. FIG. 1.-FLOW OF CURRENT IN AND AROUND A CONDUCTING BODY. For its operation, electrical prospecting mainly, depends on the fact that most metallic ores conduct an electric current much more readily than barren rocks. If an electric current flows through a block of ground within which a body of chalcopyrite is enclosed in country rock of. schist, the current will find less resistance to its passage through the chalcopyrite than through the schist, even though the passage through the latter be much shorter. This is because the longer path through the chalcopyrite offers less resistance, owing to the superior electrical conductivity of the chalcopyrite (Fig. 1).

Jan 1, 1928

By Dennis K. Mortensen

Startup of the 9000 tpd Sacaton concentrator is expected to increase Asarco's domestic copper concentrate capacity by 21%. The plant site is located due west of the mining operations, consisting of both crushing and concentrating facilities. Arthur G. McKee & Co. served as the prime contractor for the project. The Sacaton mineralization contains both sulfide and oxide ores. Primary mineral constituents are chalcocite, azurite, malachite, chrysocolla, and minor amounts of silver and occasional gold. Sulfides are distinguished from oxides when more than half the total copper content is in the form of a sulfide copper mineral. While non-sulfide copper minerals are considerably less prevalent throughout the orebody, they tend to occur quite intimately with the sulfide minerals, particularly in the upper zones of the mineralization. For this reason the decision was made to treat all the ore in a flotation circuit using existing sulfidizing methods.

Jan 11, 1974

By W. R. Hudspeth

AS an outgrowth of its spodumene recovery operation at Kings Mountain, N. C., Foote Mineral Co. has been recovering a heavy mineral by-product. Foote leased this idle plant in 1951, reactivated it, using a new spodumene recovery process, and purchased plant and properties in October 1951. While the operation at Kings Mountain is primarily concerned with the production of spodumene concentrate, pilot plant work determined that the pegmatites also contained heavy minerals including cassiterite. Plans were made to recover the heavy minerals as a by-product and the flowsheet incorporated these facilities when the mill was modified for the new spodumene recovery process. The orebodies consist of spodumene, feldspar, quartz and mica. Apatite, tourmaline, and beryl are present in small quantities. The wall rock is pre- dominantly hornblende shist. The heavy minerals, including cassiterite, columbite, pyrrhotite, monazite, pyrite, and rutile represent about 0.2 pct of the ore. The fine-grained heavy minerals are disseminated throughout the dikes, apparently unassociated with the spodumene. The pegmatites are quarried and secondary breakage is by mud-capping and block-holing. Power shovels load into trucks transporting the ore to a coarse ore bin. A Telesmith 10x36-in. apron feeder delivers the ore to an 18x36 in. Traylor Jaw crusher adjusted to discharge -3 in. product to a primary conveyor. The conveyor delivers to a 4x5-ft Tyrock single deck vibrating screen using 3/4 in. cloth. The screen undersize is elevated to the crushed ore bin. Screen oversize goes to an Allis-Chalmers Hydrocone Crusher fitted with 4 in. concave and set to deliver approximately 66 pct minus 3/4 in. The crusher discharge returns to the primary conveyor. The crushing and screening installation has a capacity of about 60 tons per hour. Spirals The crushed ore is delivered at a rate of 350 tons per day to two 6x8-ft Hardinge Pebble Mills, equipped with 20 mesh Ton-Cap trommel screens. The screen oversize is pumped to a 12-in. hydroclone for primary desliming. The hydroclone underfl spirals. There is no heavy mineral loss in the hydro-clone overflow. The spirals bank consists of eight 5-turn Model 24-A Humphreys Spirals. The top port and the last four ports of each spiral are blanked, the remaining nine port splitters are adjusted to remove about 5 pct feed weight. The heavy mineral rougher concentrates are upgraded on a Deister Overstrom table. The spiral concentrates contain approximately 4 pct heavy mineral, and the spiral reject, which goes to another section of the plant for spodumene recovery, contains about 0.03 pct heavy mineral. There is an interesting feature in the spirals installation. An adjustable splitter mounted on the discharge boxes splits out a mica fines product containing very little heavy mineral. The mica product is cleaned by spiralling and screening. Thus the spirals recover two products; mica, and a heavy mineral rougher concentrate. Table Treatment The rougher spiral concentrate goes to a Deister Plato table, modified to receive a Deister-Overstrom No. 6 rubber cover with sand riffles. The table is operated with a 5/8 in. stroke, 270 strokes per minute, and a slope of 1/2 in. per ft from feed to tailings side. There is no slope adjustment from motion to concentrate end. Wash water consumption is relatively high, since the large spodumene grains tend to report with the fine heavy minerals. A middling band about 4 in. wide is maintained in order to produce clean concentrate. The middling, representing about 10 pct of table feed, is recirculated by air-lift. A band of concentrate grade coarse spodumene occurs just below the middling. This is removed and delivered to concentrate storage. The table tailing, containing approximately 0.7 pct heavy minerals, is returned to the spodumene feed preparation circuit. The heavy mineral table concentrates are approximately 45 pct cassiterite, 33 pct columbite, 14 pct pyrrhotite and 8 pct monazite, together, with some rutile, pyrite, and copper from blasting wire. Concentrate is collected at 24 hour intervals. and dried. If the concentrate remains in wet storage appreciably longer surface oxidation takes place which seriously interferes with the subsequent magnetic separation process. About 150 lb of heavy mineral concentrate is produced per 24 hours and shipped to the company's plant at Exton, Pa. for final separation into tin and columbium concentrates.

Jan 1, 1952

Mining Methods GERALD F. SHERMAN, Chairman CHARLES F. JACKSON, Vice-chairman Alluvial Mining CLINTON BERNARD H. R. NORSWORTHY - O. B. PERRY Open-cut Mining Iron MAX H. BARBER J. A. MACKILLICAN Copper MICHAEL CURLEY R. B. TEMPEST Underground Mining Iron C. H. BAXTER TENNEY C. DESOLLAR Copper W. B. DALY R. W. THOMAS

Jan 1, 1936

By T. A. Rickard

"The chief aim in style ought to be absolute precision", said Flaubert. "There is only one noun that can express your idea, only one verb that can set that idea in motion, and only one adjective that is the proper epithet for that noun." Let this be your motto. The engineer tries to be exact in all his measurements; he should measure his language with similar exactness. The technical term is a word of precision. It is not only precise, it is a word-saver. To the unscientific the earth is "a ball slightly flattened at the poles, something like an orange". To the scientific it is "an oblate spheroid". A similar contrast between the precision of the technical term and the vagueness of common words is afforded by a conversation between Ivanhoe and Rebecca: "' What device does he bear on his shield?' asked Ivanhoe. 'Something resembling a bar of iron, and a padlock painted blue on a black shield.' 'A fetterlock and shacklebolt azure', said Ivanhoe "-using the technical terms of heraldry. It is good style in writing, however, to adapt your manner of expression to the intelligence and experience of the person or persons to whom the writing is addressed. The description of a mine should be worded differently according as it is intended to inform a mining engineer, a director, or a bishop. REMEMBER THE READER. It is as incorrect to write in a technical way for a non-technical reader as to write in a popular way for a technical or scientific reader. That style is best which enables the writer to place himself in the closest mental touch with his reader, to establish the maximum of sympathetic understanding. Let your precision be\ proportioned to your accuracy. You should not try to be precise in matters that do not admit of

Jan 1, 1931

By Joseph E. Pogue

The writer visited the Muzo emerald mines in July, 1915, and spent six days in their study. This paper embodies the results of his observations, plus information personally communicated by Robert Scheibe, Professor of Geology in the Mining Academy of Berlin, who at the time of the visit was completing a detailed field investigation of nearly a year's duration of the emerald deposits of Colombia. An elaborate account of this valuable work may be expected at a future date from the pen of Professor Scheibe.

Jan 1, 1917

By D. L. Ritter, N. J. Grant, B. C. Giessen

Forty-six alloys covering the complete concentration range of the Nb-Rh system were examined by metallographic and X-ray methods; solubility limits of terminal ad intermediate phases and transformation and solidus temperatures were determined. There are nine intermediate phases; two eutectic, five peritectic, two eutectoid, and three peritectnid reactions were encountered. The experimental methods and the constitution diagram are described in Part I. Part 11 deals with the crys -tallography and relation of the intermediate phases. The Nb-Rh system was selected for study for three reasons: first, it was hoped that the anticipated similarity of the Nb-Rh phase diagram to the Ta-Rh1 and Ta-Ir2 diagrams treated earlier (see also Ref. 3) and to the Nb-1r4 diagram treated simultaneously would allow a crystallographic and comparative evaluation of the intermediate phases in these related systems; second, it was likely that the previous experimental methods could be carried over without significant change; and third, it was expected that the interesting mechanical properties of the a1 phase of the Ta-Rh and Ta-Ir systems would also be encountered in similar phases of the new systems, and that these phases could be investigated more closely. The phase diagram had not been treated fully in the literature; only brief surveys of some intermediate phases were found.5-7 It was attempted to cover the details of the phase boundaries, Part I, as well as to present the crystallography of the intermediate phases, Part 11. EXPERIMENTAL METHODS Specimen Preparation and Treatment. The following high-purity starting materials were used. 1) Niobium powder, 99.8 pct pure, mesh size -60 +200, from Wah Chang Corp., Albany, Ore. The analysis furnished by the supplier showed the following major impurities: Ta, <500 ppm; Zr, <500 ppm; 0, 300 ppm; Fe, 280 ppm; Ti, <I50 ppm; W, Si, <100 ppm; C, N, 30 ppm; all other impurities, <30 ppm. 2) Rhodium powder, ground sponge, 99.9+ pct pure, mesh size -80, from J. Bishop Co., Malvern,

Jan 1, 1964

By Carleton Ellis

(Presented at a meeting of the New York Local Section of the Institute, Apr. 12, 1912.) I. INTRODUCTION. THE problem of the influence of hot surfaces upon gaseous combustion is one which, from a purely scientific stand-point, has engaged, for many years past, the attention of Prof. William A. Bone, of Leeds University and the Imperial College, London; and as his recent work has been the direct outcome of earlier scientific investigation, it will be appropriate, by way of introduction, to review briefly the present position of science with respect to this important subject, as stated by Professor Bone. One may perhaps best arrive at an understanding of the term " ?flameless " or " surface " combustion by considering certain facts which differentiate it from the more familiar processes of combustion as they occur in ordinary flames. All hot surfaces have an accelerating influence upon chemical changes in gaseous systems. If, at any temperature, a gaseous system, A, tends to pass over into another system, B, contact with a solid at the same temperature will accelerate the process. To take a very simple example, if a mixture of hydrogen and oxygen in their combining proportions (electrolytic gas) were maintained in an inclosure with smooth glass walls at a temperature of, say, 450° C., there would certainly be a tendency to form steam, but the rate of change would be negligibly small. If, however, there were brought into the system some porous solid material at the same temperature, so that a large surface was exposed to the gases, the rate of change would at once be rapidly accelerated in the layer of gas immediately in contact with the hot surface. Steam, the product, would diffuse outward from the surface, and the supplies of hydrogen and oxygen at the surface would be renewed by diffusion inward. Thus combustion would proceed heterogene-

Sep 1, 1912

By George S. Rice

GROUND movement from mining, whether it be for coal, metal, industrial minerals, or .oil, will always present many difficult problems. These are especially serious when valuable surface improvements may be badly damaged. The mine itself, if mining methods are not suitable to the formation, is subject to heavy falls of the main roof in the working places; and with certain structural conditions the movements may cause in coal mines disastrous bumps and outbursts of gas, and in deep metal mines rock bursts. In open-cut work rock and earth slides may result. Absolute prevention of ground movement from mining is impossible unless large pillars are left unmined,

Jan 1, 1937

By Bradley Stoughton

[Secretary&apos;s Note.—TO avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.—J. S. 1 Introduction. This paper gives the results: first,, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castr ings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows : 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such &apos;as, for example, the wear of railroad-rails, of steel and chilled-iron rolls, car-wheels, etc. 2. These improvemerits seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example: A series of tests on cast-iron

Jan 1, 1913

Furnace Builder. Engineer with extensive experience in furnace building. Position with well-established firm, branching into new fields. Location Ohio. 11-1343. Erecting and Operating Engineer to take charge of erection of gas-producer equipment and to teach customers how to operate such equipment. Location Ohio. Salary $250 per month. R-1339. Assistant Professor in Mining School, for instruction work; must have had experience in ore dressing and metallurgy. Location Missouri. Salary $1500-$2100 per school year (8 mo.). R-1332. Consulting Engineer, familiar with construction of artesian wells to act in a consulting capacity. Location New York City. R-1324. Mining Engineer and Investigator to do non-metallic mineral investigations in both field and office for United States Government. Position will last at least a year, and may become permanent. Location Washington, D. C. Salary $1800-$2700 depending on qualifications of appointee. R.-1317. Crushing Plant Superintendent, cement mill and construction experience essential. Prefer man who has had limestone crushing experience. Location New York. R-1314. Assistant Professor of Coal Mining, must be a graduate of mining engineering and have had some coal mining experience. Location Philadelphia.. Salary $2200 for school year of 10 months. R-1312.

Jan 9, 1919

By J. A. Herbst

During the last decade it has been established that conventional mineral-processing control strategies based on classical control theory result in significant increases in plant throughput and operating-cost savings. It has, however, also been recognized that conventional strategies have important limitations for complex multivariable mineral-processing systems. These limitations center around the fact that single-input/single- output control linkings often result in highly undesirable interactions between controllers. During the last few years new and promising approaches to solving this problem have emerged. These approaches are based on the use of on-line dynamic models to make predictions which are useful for control decision-making. This paper presents a brief summary of the state-of-the-art for mineral-processing control in 1984. This summary is followed by a review of recent developments in model-based control strategies including those in optimal control, self- tuning regulators and decoupling control. Expected trends for the future in the control of mineral-processing operations are discussed.

Jan 1, 1984

By Augustus Locke

I WISH to urge on this Committee the task of evaluating mining geology. -My motive is as follows: It, is a. duty of the Institute from time to5 time, to establish the social perspective of the professions grouped within it, not simply to promote their use, but to determine with engineering definiteness their true powers and functions. This becomes the delegated duty, therefore, of this committee in respect to geology. Be- cause my own subject is mining, I shall confine my remarks to mining geology. But I believe that the evaluation should be made to include all of that geology termed economic. The perspective for such evaluation is shown in the nature of the public support given to geology. The federal Geological Survey, the leading organization on the economic side, is actuated by the zeal of a small group of devoted professionals who consider its work valuable, &apos; It proceeds, however, on a starvation ration of appropriations, and that implies that neither the corporations, the voters nor the vote getters consider it important. Altogether, in&apos; the public consciousness, geology is negligible. That, at the same moment, .the profession should act with full confidence, while everyone else should act&apos; with opposite motives, is not fitting. For us, as a committee, to remain incurious regarding such a disparity of beliefs is quite impossible.

Jan 1, 1931

By Y. C. Liu, G. A. Alers

The anisotropy of Young&apos;s modules has been measured in a series of Cu-Zn alloys containing from 1 to 28 wt pct Zn and cold-rolled to 97.5 pct reduction in thickness. These modulus data show a transition in texture as a function of zinc content. In alloys containing 3 pct Zn or less, the texture is essentially that of copper. A transition is clearly seen to develop in 5 and 8 pct Zn alloys, and to have been completed in a 12 pct Zn alloy. Increasing the proportion of zinc to 28 pct does not produce any further changes in texture. The ease and clarity with which this texture transition can be seen in the modulus data is in great contrast with the inccertainty in the visual detertiination of the range of texture transition from a series of pole figures. It is also shown that the rolling texture of the high zinc content alloys cannot be a one-COIIIponenl texture, characterized by the (110)(112) ideal orientations, as usually assumed. A second, quite important component must also be present. Furthermore, the present data are inconsistent with matrix orientations on which the "oriented growth" hypothesis of the Formation of recrystallization textures is based. THE rolling textures of binary fcc alloy systems have generally been considered to lie between two terminal textures. One of these terminal textures is the copper type and the other is the 70:30 brass type. Alloys of intermediate solute content exhibit a texture which is said to be a transition between the two terminal textures. On the basis of efforts to correlate rolling and recrystallization textures, two concepts have been advanced in the literature on the nature of these transition textures. One school1 suggests that the addition of alloying elements, e.g., zinc, causes a gradual rotation about one of the (111) poles from the (358)( 523) ideal orientation of the copper-type rolling texture to the terminal {1 10)( 112) ideal orientation used to describe the rolling texture of 70:30 brass. This concept is depicted in Fig. 1 with the angle of rotation corresponding approximately to the zinc content and is designated here as the "rotational concept", since the ideal orientation of the transition textures varies continuously with alloy content. The other concept,&apos; the "mixture concept", suggests that the copper-type rolling texture is a two-component texture. {358) (523) and {110)(112). The addition of alloying elements affects only quantitatively the relative amounts of these two components—a decrease in the amount of material in the {385}(523) orientation and an increase of that in the {110)(112) orientation with increasing solute content. An experimental distinction between these two concepts is essential to a better understanding of both the mechanism of formation of rolling textures and the subsequent formation of recrystailization textures in fcc metals. Because of the lack of resolution inherent in pole figures, it has not been possible to differentiate between the two concepts on the basis of this data. Both concepts, in fact, make use of the same set of pole figures but interpret them in a manner acco-rding to the view held.&apos;" Experimental results obtained from inverse pole figures or selected-area electron diffraction3j4 simply -yield more refined pole figures but do not eliminate the ambiguity of interpretation. Quantitative measurement of an entirely different, orientation-dependent property must thus be considered

Jan 1, 1967

By George Bain

SOME problems concomitant with commercial exploitation of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service depart-ment wants defects rectified and the cause determined to avoid recurrence. The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character.

Jan 1, 1940

By John J. Strohl, Henry J. Schwellenbach

This paper relates the results obtained by decreasing the size of feed to a rod mill screen circuit. As would be expected, added production was gained and a finer grind with no tonnage loss was made possible.

Jan 12, 1950

Teamwork: The famous first sentence of an essay en- titled Aphorisms, by Hippocrates, is as follows: "Life is short, the Art long, opportunity fleeting, experience treacherous, judgment difficult." The future of science does not depend so much on the number of scientists or the number of colleges, but rather on the individual qualities and the degree of perfection of a limited group of leading scientists and colleges. These are individual factors which require inherent talent which in turn is a condition evolved after generations of culture. Thus, very elaborate higher education for indiscriminate masses of humanity or students may not necessarily show the expected results. In other words, it is possible that higher specialized education should be given only to the few talented individuals, and their capacity and worth should be judged by as highly qualified and talented teachers. Quality is the greatest of all competitive aids. An essential qualification that must be possessed by a quality mineral industries college is a high caliber teaching staff, for the mineral sciences will advance in the coming years only if the leading minds of today are made avail- able as the mental springboards for our scientists of tomorrow. Mineral industries schools are finding it increasingly difficult to maintain a high caliber staff of instructors and administrators in competition with private business and governmental demands for similar

Jan 1, 1950

By John S. Alexander

By Henry F. Cooper, Scott E. Blouin

Large jacking test procedures that have been applied to obtain static in-situ rock properties (Ref. 1) have shown that the in-situ rock modulus and strength can be considerably less than what would be obtained from laboratory tests on intact samples. This trend is also expected to be true for dynamic properties, but few dynamic in- situ rock property tests have been conducted. During the past several years, high explosive test procedures have been developed to simulate the airblast and direct induced ground motions (Ref. 2) produced by nuclear explosions . These test procedures load large volumes (up to 10 7 f t3) of the earth with stress levels sufficiently high to produc5 feet of particle displacement over surface areas up to l0 5 ft2. This paper discusses some of the data obtained, and the implications of these results for our understanding of the dynamic response of in-situ rock. DESCRIPTION OF TEST PROCEDURES As shown in Fig. 1, the High Explosive Simulation Technique (HEST) consists of a cavity of uniform height bounded on the sides by a soil berm, above by an overburden of uniform thickness, and below by the test bed on the earth&apos;s surface. Horizontal racks of detonating cord are placed in the cavity and detonated at one end of the test bed. This detonation produces an explosive wave that propagates across the test bed, loading the earth with an overpressure pulse that decays with time because of the compression and lifting of the overburden. Since 1964, there have been approximately 40 such tests on test bed areas ranging from a few hundred to l0 5 sq ft., simulating peak overpressure conditions between about 100 and 6000 psi and specific impulses between a few and over 100 psi-sec.

Jan 1, 1971

By Elton A., Youngberg

The Holden mine operated by the Chelan Division of the Howe Sound Co. is on the east slope of the Cascade Range in north central Washington on the south slope of Railroad Creek valley at an elevation of 3500 ft. The mine may be reached by a 40 mile boat trip from the town of Chelan which is at the southern tip of Lake Chelan, to Lucerne at the mouth of Railroad Creek and an 11 mile bus ride up Railroad Creek to Holden. All freight and concentrate is moved over this route to Chelan Falls on the Columbia River which is on the railroad four miles below the town of Chelan. The mine is now producing 2000 tons of gold, copper, and zinc ore per day which is treated in the Holden mill. Gold-copper and zinc concentrates are made, the first of which is shipped to Tacoma, Wash., and the latter to Kellogg, Idaho, for smelting.

Jan 1, 1949