Search Documents

By J. D. Livingston, H. E. Cline

The lamellar-dendritic transition in Sn-Pb alloys near the eutectic composition has been studied at high growth rates. Lamellar structures were found over a substantial range of tin-rich compositions, and this range extended to increasingly tin-rich concentrations as growth rate increased. These results are discussed in terms of stability and competitive-growth arguments. Various experimental and structural limitations to the rate of directional solidification are discussed. The rate of heat removal at the heat sink is the major experimental limitation. ReCENT interet1,2 in the use of fine composite structures produced by directional solidification of eutectic alloys makes it important to determine the range of composition and growth conditions that yield such microstructures. Because increasing growth velocities produce increasingly finer microstructures, it is particularly significant to determine the factors limiting the rate of solidification. Mollard and Flemings3 have shown that composite structures, free of primary dendrites, can be obtained in Sn-Pb alloys of off-eutectic composition. The composition range of composite structures was found to increase with increasing values of G/V, where G is the temperature gradient and V is the growth velocity. These results are in good quantitative agreement with an analysis of the stability of a planar eutectic interface.4 This analysis specifically predicts that over a small range of compositions stable lamellar structures will be obtained even for G/V = 0, hence, even at very high growth rates. The lamellar-dendritic transition in Sn-Pb alloys has also been analyzed with a model based on competitive growth between dendrites and the composite structure.576 This treatment, based on earlier work on organic eutetics,7 predicts that the composition range yielding composite structures in Sn-Pb will increase rapidly at high growth rates. An increase in the composition range of composite structures at high growth rates was recently observed in Cu-Pb alloys near the monotectic composition.8 In view of these results, and the predictions of the stability and competitivegrowth analyses, it was decided to study the lamellar-dendritic transition in Sn-Pb alloys at high growth rates. EXPERIMENTAL Using 99.999 pct pure materials, a series of Sn-Pb alloys were prepared containing 16.8 at. pct to 27.6 at. pct lead. (Eutectic composition is 26.1 at. pct Pb.) Ingots were extruded to 0.175 in. rod, and some rod was drawn to 0.070-in. wire. Directional solidification was accomplished in two different ways, Fig. 1. For growth rates up to 2 x 10-1 cm per sec, a 0.175 in. diam sample was placed in a graphite crucible 5 in. long with 0.250 in. OD and 0.035 in. walls. Samples were melted under flowing argon in a vertical, platinum-wound furnace, and solidified by driving the crucible downwards through a \ in. hole in a water-cooled copper toroid, Fig. l(a). An insulated chromel-alumel thermocouple was imbedded in the center of a representative sample, and moved with the sample during solidification. The local temperature is plotted against the distance travelled by the sample in Fig. 2. As the growth rate increased, the solid-liquid interface moved closer to the water-cooled toroid and the temperature gradient increased. At growth rates above 10-1' cm per sec, heat was not removed fast enough and the sample moved into the toroid in the liquid state. The curve for V = 2 x 10-1 cm per sec shows a plateau caused by incomplete removal of latent heat from the interface, a problem which will be discussed later. To improve the heat removal, the toroid was cooled by nitrogen gas precooled in liquid nitrogen. This allowed successful solidification at rates up to 2 x 10-1cm per sec. Higher solidification rates required still more effective heat removal. Samples 0.070 in. in diam were placed in graphite tubes 0.125 in. in diam with 0.020 in. walls. Instead of cooling by sliding contact with a cooled toroid, these thinner samples were sprayed or directly immersed into water, Fig. l(b). After solidification, samples were stored in liquid nitrogen until they could be examined metallographic-ally. The surface was prepared with a diamond-knife microtome, followed by a light etch. The presence or absence of tin dendrites, Fig. 3, or lead dendrites, Fig. 4, was noted by optical microscopy, usually of a transverse section near the center of the sample. Replicas of the surface were prepared and examined in an electron microscope to resolve the fine lamellar structures, Fig. 5. The structures observed at various compositions and growth rates are summarized in Fig. 6. Composite structures were observed at increasingly cin-rich compositions as growth rate increased. This transition from dendritic to composite structure with increasing growth rate was also demonstrated by solidifying half a sample at a slow rate and then suddenly increasing the growth rate by lifting the furnace and quenching the sample with a water spray. A longitudinal section of this sample, Fig. 7, shows that the tin dendrites, which extended ahead of the slow-moving composite interface, were bypassed by the composite when the growth rate was increased. The range of composite structures at high growth rates was limited by the appearance of primary lead dendrites on the tin-rich side of the eutectic composition. Observation of representative longitudinal

Jan 1, 1970

By L. L. McDaniel

Copper smelters of various kinds have operated in the Morenci district since 1872, but all have been abandoned with the exception of the present Morenci Smelter of Phelps Dodge Corporation, which was completed in 1942. During the five-year period starting in 1937, the Morenci ore body was prepared for open pit mining, pilot mill test work was carried out, and a complete reduction works, of which the Smelter is a part, was designed and erected. Actual construction work on the Morenci Smelter was started in the fall of 1940, and warming up of the units began on April 1, 1942. Charging of the reverberatory furnaces commenced on April 18, 1942, and the first anode copper was produced on April 26, 1942. The smelter was originally designed to handle the production of the Morenci Concentrator on a 25,000 ton per day program, but by the time the smelter was in operation, plans were already underway to increase the smelter capacity to handle the production of the concentrator which was being enlarged to 45,000 tons a day capacity as a war-time necessity. This extension to the smelter was completed and the new units were put in operation toward the beginning of 1944. The original smelter consisted of a smelter crushing plant, bedding plant, two direct-smelting reverberatory furnaces with two waste-heat boilers on each furnace, three converters, an anode department, a stack, and all of the usual accessory smelting equipment. The extension consisted of increasing the bedding plant from three to five beds, the reverberatory department from two to four furnaces, and from four to eight waste-heat boilers, and the converter department from three to six converters. A third converter aisle crane was added and additions were made to the flue systems and conveyor systems throughout the smelter; but no change was made in the smelter crushing plant or the anode department, and the same stack was used for all additional Smelter units. A blister casting machine was installed at that time in the south end of the converter aisle to handle excess and emergency production above the capacity of the anode department and in 1947 a converter aisle skull breaker and a lime burning plant were added as the final units for a complete plant. The choice of direct smelting over calcine smelting for the Morenci Smelter was made after careful study by members of the Western organization of Phelps Dodge Corporation and after test runs on direct smelting of Morenci concentrate had been made at the Douglas Smelter of Phelps Dodge Corporation. The Morenci furnace charge is made up of comparatively high grade concentrate with no ores of smelting grade available and with only flux, a small amount of copper precipitate and the usual amount of smelter secondaries to be smelted with the concentrate. The simplicity of direct smelting for this charge and the large amount of waste-heat steam available from direct smelting operations were factors influencing the decision to adopt direct smelting for Morenci. The design of the Morenci Smelter and the type of units selected followed best experience at the Douglas Smelter of Phelps Dodge Corporation. A description of the original smelter before operations started was given in an article in the May 1942 issue of Mining and Metallurgy. The purpose of the present article is to describe the enlarged Morenci Smelter, with a discussion of metallurgy and operating practice and to show tabulations of operating and metallurgical results obtained. Because of beginning operations during the early years of World War 11, many problems caused by labor shortage were encountered, but no major difficulties developed in starting the new plant. However, because of labor shortage, full scale Smelter production was not reached until the fall of 1946. Fig 1 shows a general plan of the Morenci Reduction Works. The arrangement of the smelter equipment is shown in Fig 2, a sectional view of the smelter is shown in Fig 3, and the smelter flow sheet is shown in Fig 4. Metallurgy The metallurgy of direct smelting, being more or less fixed by the character of the charge, is not subject to the control available in calcine smelting. Slags may be modified by the addition of suitable fluxes, but the grade of the matte is determined almost entirely by the iron:copper ratio of the concentrate. The direct smelting operation involves distributing the wet concentrate along the sidewalls and in the bath of a reverberatory furnace by means of some suitable feeding device and raising the temperature of the charge so that first the moisture is driven off, then the first-atom sulphur is eliminated, and finally the sulphide portion of the charge melts and runs into the bath, carrying with it the non-sulphide portion which has been partially fluxed to form a suitable slag. The fusion of the non-sulphide portion is completed by contact with the irony converter slag which is regularly being poured into the reverberatory furnace. The smelting rate of the charge is influenced by the mineralogi-cal composition of the sulphide portion of the concentrate and by the composition and amount of the non-sulphide portion including the fluxes added. The copper in Morenci concentrate is chiefly in the form of chalcocite, intimately associated with pyrite, and non-sulphide content is very low so that

Jan 1, 1950

By C. W. Chen

MARTENSITE transformations in ß Cu-Al alloys have been studied by Greninger1 and other investigators. According to Greninger, the parent phase ß1 an ordered body-centered-cubic structure obtained from ß phase by suppressing the eutectoid decomposition, transforms into an ordered hexagonal-close-packed phase in composition containing 12.9 to 14.7 pct Al. The M, temperature decreases with increasing aluminum content; for the alloy containing 14.5 pct Al, for example, the ß1??' transformation occurs below room temperature. More recently, Kurjumow2 studied the transformation in ß Cu-Al alloys with the addition of nickel. His report stimulated new interest in the subject due to the observation of completely reversible transformation without hysteresis in the transformation temperature ranging from 10° to —10°C. In the present paper some characteristics are described of the transformation of Cu-Al-Ni alloys that were partly studied by Kurjumow. Experimental Procedure High purity copper (99.999 pct) and aluminum (99.99 pct) and electrolytic nickel were used in the preparation, by the Bridgman technique, of single crystal specimens which contained aluminum and nickel of 14.5 and 0.5 to 3.0 pct, respectively. Polished surfaces were prepared mechanically. Specimens were then chemically etched to remove distorted material, homogenized at 1000°C for several hours, and quenched drastically to room temperature in a 10 pct NaOH bath to produce the parent phase ß1. The transformation was studied under a microscope and, in some cases, recorded by means of motion pictures. A device similar to that designed by Greninger and Mooradian3 was used to cool and reheat the specimens. Results and Discussion When the specimens were cooled below room temperature, the ß1 to ?' transformation began at 10°C with the appearance of ?' crystals In relief, Fig. la. As the specimen temperature dropped further, the transformation continued, either by the growth of the ?' crystals, with the ß1 — ?' interface moving into the ß1 phase, Fig. 1c and 1d, or by the formation of new ?' crystals, Fig. 1b. As a consequence of the former process, banded structure is observed as a common feature of the low temperature phase. According to the theory of the formation of martensite by Wechsler, Lieberman, and Read,' the bands of ?' phase are probably twin-related, as is the case in the diffusionless phase change of In-T1 alloys,5 but this was not revealed by X-ray tech- niques. New ?' crystals, in needle form, often emerged suddenly across the ?' bands during the transformation. These acicular crystals then grew, both in length and in width, see Fig. 2a through 2d. The transformation on cooling is completed at about -35°C. Upon heating, the reverse transformation started at —10° C, in a manner nearly opposite to the transformation on cooling, and completed at 35°C. There was no noticeable change in the transformation temperature when the nickel content was varied within the limits previously mentioned. Through control of the specimen temperature, the transformation can be started, stopped, or reversed at will. This phenomenon has frequently been observed in the martensite transformation of many nonferrous alloy systems. Other systems are Au-Cd6 and In-Tl.5 ow-- ever, in the latter systems, the transformation is accomplished by single interface motion if the specimen composition is homogeneous and the temperature gradient in the specimen is uniform and sharp, whereas in the Cu-Al-Ni specimens, only multiple interface transformation is observed. The speed of the interface motion appears to be a functionof the rate of temperature change and the temperature gradient across the specimen length. In one case, in which the temperature increased at the rate of 10°C per min and there was no temperature gradient along the specimen axis, the speed of the disappearance of a ?' plate was determined, by the study of the motion pictures made, to be 26 µ per sec. Quench markings were observed on the polished surfaces of specimens. The markings were grouped into one or more sets of different orientations, and were parallel in each set. The ?' plates formed in subsequent transformation were parallel to the markings, indicating that the ?' plates and the quench markings had the same geometric relation-ship to the ß1 matrix. The quench markings on two intersecting surfaces of a specimen were therefore used in the determination of the habit plane of transformation, by the trace method suggested by Barrett.' Results obtained from five sets of markings in three specimens indicate that the habit plane is an irrational plane about 2" from one of the {221} planes. This is very close to the habit plane (3" from 221 planes) of ß Cu-Al alloys containing more than 13.0 pct Al.1 The martensite transformation of Cu-Al-Ni alloys is reproducible. No sluggishness was found between consecutive transformation cycles, although a slight difference in the distribution pattern of the ?' plates was observed, compare Figs. Id and 2d. The transformation can be strain-induced. This characteristic has been tested by a simple method. When a specimen was elastically strained slowly in a vise, ?' plates were gradually produced in the same fashion as during transformation on cooling, This test was done at room temperature, and thus above the M,

Jan 1, 1958

By K. A. Gschneidner, O. D. McMasters, T. J. O’Keefe

X-ray diffraction, differential thermal, ad rnetallo-graphic methods were used to establish the Dy-Pb Phase diagram. Lead additions lower the 1377°C transformation temperature of dysprosium to 1360°C leading to an inverted peritectic reaction. The 327°C melting point of lead is lowered by dysprosium additions to about 326°C yielding a eutectic reaction. A second eutectic reaction occurs at 13.3 at. pct Pb and 1200°C. The dysprosium-richest intermetallic compound DysPb3 melts congruently at 1695°C and crystallizes in the hexagonal Mn5Si3 (D8,) type structure. The peritectic decomposition temperatures for the remaining compounds are Dy5Pb, at 1555C, DyPb2 at 955C, and DyPb3 at 880°C. A fifth compound near the DyPb stoichiometry exists over a 310°C temperature range decomposing at 1130°C by means of an inverted peritectic reaction and melting incongruently at 1440°C. The crystal structures of the compounds are discussed. A systematic study of the rare earth-lead alloy systems is underway in an effort to supply information concerning the alloying behavior of the rare earth metals. The Dy-Pb phase diagram is the fourth system to be investigated in this study. The Yb-Pb,1 Y-Pb,2 and Eu-Pb 3 diagrams have been published recently. Utilization of the rare earth series of metals as a research tool in this manner should yield a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The lead used in this investigation was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The dysprosium was prepared in this Laboratory by the calcium reduction of the fluoride followed by distillation of the dysprosium. The major impurities in the dysprosium in ppm are: A1 (<40), Ca (400), Er (<50), Gd (<200), Ho (<200), Mg (<50), Si (30), Ta (400), Tb (<100), Y (<50), 0 (651, H (15), N (not detected), F (430), C (35). Alloy Preparation. Most of the alloys were prepared by melting weighed amounts of dysprosium and lead in sealed tantalum crucibles. The tantalum crucibles were sealed by are-welding in a He-Ar atmosphere welding chamber. Thus the alloys are in contact with He-Ar at about 1 atm pressure. Homogenization was achieved by holding them in the liquid state for about 1 hr, cooling, inverting the crucibles, remelting, and repeating the process at least twice. Since these alloys were prepared in sealed tantalum crucibles, chemical analysis for final composition was thought to be unnecessary. No detectable reaction of these alloys with the tantalum crucible was observed by metallographic examination. Metallographic evidence was also used to confirm the homogeneity of some of the alloys prepared in this manner. The compositions of a few alloys, which were prepared by nonconsum-able are-melting, were corrected for the small weight losses involved by assuming that the weight loss is due to vaporization of lead. The specimens obtained from the alloy samples were prepared under a dry-argon atmosphere because they were rapidly attacked by air and moisture. Thermal Analysis. Differential thermal analysis methods were used to determine the liquidus curves and reaction horizontals of the system. Both Pt vs Pt + 13 pct Rh and W + 5 pct Re vs W + 26 pct Re thermocouples were used to measure the temperature. An X- Y recorder was used to record the specimen temperature and differential electromotive force between the specimen and molybdenum standard. The arrest temperatures were measured potentiometri-cally. The accuracy limits (* values) associated with the reaction temperatures obtained by this method were estimated on the basis of both the reproducibility of the particular temperature value and the accuracy of the thermocouple at a given temperature. Liquidus temperatures were obtained from cooling arrest data while both heating and cooling arrest data were used to establish the horizontals of the diagram. Heat treatments during the thermal analyses of the alloys between 40 and 70 at. pct Pb were necessary in order to approach equilibrium conditions. The samples were held at temperatures between the various peritectic horizontals for l to 2 hr before the thermal analyses were continued. The entire range of compositions was investigated at the expense of a minimum amount of materials by adding appropriate amounts of lead to master alloys. More than sixty alloys were analyzed by this differential thermal method and for each alloy the results given herein are taken from two or three heating and cooling cycles. X-Ray and Metallographic Methods. Slice specimens for metallography and powder specimens for X-ray diffraction were prepared from rod-shaped samples which had been melted in sealed 0.62 5-cm-diam tantalum crucibles. The specimens were heat-treated in sealed tantalum crucibles which were protected by sealing them in argon-filled quartz ampules. Quenching was accomplished by breaking the ampules in ice water after heat treatment. X-ray powder specimens were sealed in 0.3-mm-diam glass capillaries under a dry-argon atmosphere. Copper, iron, and chromium radiation were used to obtain the powder patterns for these alloys. More than 150 powder patterns were obtained for specimens of various compositions and heat treatments. Included in these were several patterns for specimens which had purposely been oxidized. Patterns from specimens which had been accidentally exposed

Jan 1, 1969

By Amitava Gangulee, Michael B. Bever

The effects of changes in short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions have been investigated. The heats of formation at 273°K of several alloys after two different thermal treatments were measured by liquid metal solution calorimetry. Their electrical resistivities were measured at temperatures ranging from 4° to 773°k. Tensile tests and microhard-ness measurements were carried out at room temperature. An effective short-range order parameter and an effective interaction energy are defined. The measured changes in the properties are interpreted in terms of these quantities. The short-range order parameter is evaluated separately from calorimetric and X-ray data; the results are in fair agreement. Increasing short-range order lowers the resistivity of- the silver-rich Ag-Mg alloys but does not measurably affect the temperature dependence of the resistivity. Short-range order increases the yield stress of these alloys but does not affect the ultimate tensile stress. Changes in the effective short-range order parameter independently obtained from measured changes in the heat of formation, resistivity, and yield stress are in fair agreement. THE thermodynamic, electrical, and mechanical properties of solid solutions have been investigated as functions of composition in many alloy systems, but the effects of configurational variables, such as short-range or long-range order, on these properties have received much less attention. The silver-rich terminal solid solutions in the system Ag-Mg are well-suited for the investigation of the effects of order. The composition of these solid solutions may be varied over a range extending to about 27 at. pct Mg.1 Appreciable short-range ordering is likely to take place in these solid solutions; the degree of short-range order can be varied by suitable thermal treatments. In the alloy Ag3Mg long-range ordering is possible.2 This paper is primarily concerned with the effects of short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions.-The long-range ordering transition is the subject of a concurrent paper.3 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Specimens. Ag-Mg alloys containing up to 26.4 at. pct Mg were prepared by melting 99.99 pct pure Ag (obtained from Baker Chemical Co.) and 99.99 pct pure Mg (obtained from Eastman Chemi- cal Co. or Johnson Mathey & Co.) in graphite crucibles under molten potassium chloride. The solidified ingots were homogenized at 823°K for 10 days in evacuated Vycor capsules. A surface layer 6 in. thick was then removed by machining. The ingots were swaged into rods (2.5 mm diam) which were drawn into wires (1.0 mm diam). The wire specimens were annealed at 773°K for 24 hr in vacuum and either quenched into iced brine or cooled to room temperature over a period of 15 days. The average grain diameter (obtained from the linear intercepts) was about 0.1 mm. 1.2) Calorimetry. The heats of formation of the alloys were measured in a tin solution calorimeter as the difference in the heat effects of alternate additions of samples of an alloy and the mechanical mixture of its component elements. The additions were made from 273°K to the bath at about 623°K. The heat effect on addition of the alloys was approximately 5.5 kcal per g-atom. The procedure and the method of calculation have been described.4 1.3) X-Ray Diffraction. Short-range order parameters of two alloys were calculated from diffuse scattering intensities,&apos; obtained with briquettes made from powdered specimens. A GE-XRD 5 diffractometer with filtered copper radiation was used. The absolute intensities were based on calibrations with paraffin. 1.4) Resistivity Measurements. The electrical resistivities were measured by a potentiometric method in which the potential drop across the specimen was compared with that across a standard resistance. For measurements below room temperature, the specimens were immersed in liquid helium (4°K), liquid nitrogen (78°K), dry ice and trichloroethylene (195°K), or ice and water (273°K). Measurements above room temperature were made on specimens held in a furnace under helium or in vacuum. The resistivity measurements were reproducible to ±0.5 pct or less. 1.5) Mechanical Tests. Tensile tests were carried out at room temperature with a Tinius-Olsen XY elec-tromatic Universal testing machine. Wire specimens (nominal gage length 1 in.) were used. The strain was measured with an extensometer, which had a sensitivity of 4 x 10-5; the strain rate was 10-3 min-1. Microhard-ness measurements were made with a square-pyramid indenter and a 100-g load.11 2) RESULTS AND DISCUSSION All measurements were made on two parallel sets of specimens, one quenched and the other slowly cooled from 773°K. The reported values are the averages of at least three measurements. In the range of magnesium concentration substantially below that of the composition Ag3Mg, quenched alloys have less short-range order than slowly cooled alloys. As the magnesium concentration approaches that of Ag3Mg, slow cooling develops long-range order. Quenching sup-

Jan 1, 1969

By I. J. Hegyi, J. J. Tietjen, H. Nelson, J. I. Pankove

The fabrication of p-n junctions in GaAsl-,P, alloys by a vapor-phase gowth technique has for the first tirne resulted in room-temperature injection lasers capable of operating over a broad range of wavelengths extending into the visible region of the spectrum. The shortest wavelength achieved to date is 6750A at room tetnperature. In addition, at 78°K the threshold current density values for these lasers are generally the lo~vest reported, and the emitted radiation extends to the lozc,est wavelength ever attained (6350A). With lasers fabricated from material containing 14 pct Gap, quanticm efficiencies of 26 pct and peak power outputs of 25 zu were obtained at room temperature. ALTHOUGH room-temperature operation of GaAs injection lasers has been well-documented,&apos;-5 the operation of GaAsl-,P, (x > 0) laser diodes has been restricted to relatively low temperatures.8-&apos;0 This has been previously attributed5, 7, 10-12 partially to the difficulty of preparing single-crystalline GaAsl-& alloys having a high degree of chemical homogeneity and purity. Also, with these materials it has been difficult to prepare high-quality, abrupt p-12 junctions by diffusion techniques; and, in turn, this has made it difficult to obtain optimum electrical properties for room-temperature operationL3 in the resulting laser diodes. As a result, GaAsl-,P, laser diodes have not been efficient enough to permit operation at room temperature. For example, using diffused structures, only a few diodes were obtained which could be operated even close to room temperature (255K)." Recently, a vapor-phase growth method of preparing epitaxial deposits of GaAsl - .P, alloys has been described,14 and the high-purity and homogeneity of these materials has been previously demonstrated. Of special significance, with this technique, n- or p -type doping can be initiated or discontinued at any time and at almost any rate during the crystal growth so that the donor and the acceptor concentrations can be easily controlled to obtain desired impurity profiles. This permits high-quality, abrupt p-TZ junctions to be vapor-phase grown entirely during the crystal growth process, so that diffusion or other p-n junction fabrication processes are unnecessary. After growth, the device does not have to be heated to elevated temperatures, which avoids the possible unwanted introduction and motion of both impurities and lattice defects. Using the vapor-phase growth method cited above, over 300 room-temperature injection lasers have been prepared from GaAsl-,P, alloys having compositions in the range of 0 5 x 5 0.41. These lasers have emitted cohe~ent radiation in the spectral range of 8350 to 6350A at 78°K or from 9000 to 6750A at room temperature. The threshold current densities of the best lasers are independent of the alloy composition over the range 0 < x < 0.2 and compare favorably with values for good GaAs lasers.&apos; MATERIAL PREPARATION Multilayer, epitaxial deposits of GaAsl-,P, alloys are prepared by a vapor-growth technique described elsewhere.14 With this technique, the individual layers which comprise the multilayer structure are prepared sequentially in the deposition apparatus without interrupting the crystal growth. The epitaxial layers are deposited on GaAs substrate surfaces oriented normal to the ( 100) direction. The substrate wafers employed in this study were usually doped with tellurium to an electron concentration of approximately 2 x 10" per cu cm. To avoid strains, the first 10 to 15 p of the deposited material is uniformly graded from pure GaAs to the specific GaAsl- ,P, alloy composition of interest. The GaAsl - ,P, alloy growth is then continued to form a layer of constant composition having a thickness in the range of 25 to 75 p. Both the graded region and the layer of constant composition are doped with selenium to an electron concentration of about 2 x 10" per cu cm. The p region of the diode is then incorporated in the crystal by abruptly changing the dopant concentrations in the vapor phase to facilitate doping with zinc. This layer has a hole concentration of approximately 3 X 1019 per cu cm and typically is 50 p thick. DEVICE FABRICATION In general, the GaAs substrate and the region of graded composition are removed. Ohmic contacts are made to the n-type side by tin evaporation and to the p-type side by an electrodeless nickel deposition. This is followed by an electrodeless deposition of gold on both sides. The crystal wafer is then cleaved along (110) planes and sawed into rectangular parallelepipeds. Typical dimensions are 100 by 300 for the junction area and 100 µ for the diode height. The diodes are either soldered to a copper stud or pressure-mounted in a copper clip. RESULTS AND DISCUSSION Approximately 400 laser diodes having compositions in the range of 0.41 have been prepared by the method described above. Each laser was routinely tested at liquid-nitrogen temperature. The lasers were operated with l-psec current pulses at a repetition rate of 60 pulses per sec. The parameters of greatest practical interest are the photon energy or wavelength of the laser output and the threshold current density. Fig. 1 shows the variation of photon energy with alloy composition at 78°K. The composition was determined from the lattice constant of the material obtained by X-ray back-reflection measurements. Although there

Jan 1, 1968

By S. R. Goodman, Hsun Hu

The formation of secondary - recrystallization tex-tlires in cube-textured 18-8 stain less steel (Type 304) Ilas been studied at three temperatures. Prolonged annealing at 100°&apos;C protluces a PredoninanGly (520) [OOZJ-type texture, which is related to the cube te.ture of the primary lnatrix by a rotation of approxivzately 22 deg around the [001] axis in the rolling direction. Annealing at 1200 or 1300°C facers the formation of the (123)[272/-type texture, which is related to the matrix texture by a [111] rotation of app.voxiniately 40 deg. These observations suggest that in the secondary recrystallization of cube-texlut-ed stainless steel an apparent actilation energy for growth is higher for grains related to the tncrtuix Og [111] rotations thun those reloted by [100] rotations. THE formation of secondary-recrystallization textures in cube-textured primary matrices of fcc metals has been studied widely by various investigators. For Fe-40 pct Ni alloys, Pawlek&apos; and wassermann2 reported that the orientations of secondary grains were related to the cube texture by rotations of 30 and 38 deg around [001] in the rolling direction. However, Rathenau and custers3 found that, while in one Fe-48 pct Ni alloy, most of the secondary grains were oriented with respect to the cube-textured matrix by rotations around [001] of 26.5 deg, in another alloy of a different origin, the orientations of secondary grains were related to the cube texture by rotations of approximately 35 deg around a [lll] axis. Similar orientation relationships were also observed between the secondary grains and the cube-textured primary matrices of copper.4"a No attempt was made to differentiate these two types of orientation relationships; reorientation by either a [111] or a [100] rotation was considered to be equally favored. The present investigation consisted of a study of the secondary recrystallization textures in cube-textured stainless steel. It was noted that the secondary grains formed in stainless steel were considerably smaller than those of Fe-Ni alloys or copper. This offered the advantage that the secondary recrystallization texture could be determined by the texture-goniometer technique, and a more detailed study of the textural development during the course of secondary recrystallization could be made. The effect of annealing temperature on the formation of secondary-recrystallization textures was also investigated. MATERLAL AND METHOD It was shown earlier"-" that a strong cube texture can be obtained in 18-8 stainless steels by rolling at 800°C to produce the copper-type deformation texture, followed by annealing at 800" to 1000°C for recrystallization. To improve the cube texture for the present study, a commercial-grade 18-8 stainless steel (Type 304) was rolled at 800°C first to 5 mm (0.2 in.) thick plates. Three of these plates were then stacked and welded together along the edges into a sandwich assembly. After annealing at 900°C for 20 min: the assembly was finally rolled at 800&apos;C to 90 pct reduction in thickness with reheats and end-for-end reversals after each pass. Only the central strip, which was reduced from 5.0 to 0.50 mm (0.7 in. to 0.020 in.) thick, was used. The chemical composition of the steel in weight percent was as follows: C, 0.06; Mn, 0.38: Cr, 18.71; Ni, 9.56: P, 0.011; S, 0.009; and Si, 0.39. The purpose of rolling the strip in a sandwich assembly was to prevent direct contact between the central strip and the rolls. It was observed earlier" that, when the strip was rolled at 800°C without being enclosed in a sandwich assembly, the cube texture obtained by subsequent annealing at 900" or 1000° C for recrystallization was largely confined to the central section of the strip, while most of the recrystallized grains formed in the surface section of the strip were not cube-textured. This was obviously due to the fact that the actual temperature at the strip surface during rolling, as a result of direct contact between the strip and the cold and massive rolls, was considerably lower than 800°C. By using a sandwich assembly for hot rolling, the cube texture obtained upon subsequent annealing for recrystallization was found to extend through the entire thickness of the strip. After rolling, the central strip was taken from the sandwich assembly. and cut into specimens. Prior to annealing. the specimens were etched to 0.25 mm (0.010 in.) thick. A tube furnace provided with a purified, dry argon atmosphere was used for annealing. Textures were determined by the reflection technique. using a Siemens automatic texture-goniometer and ZrOz-filtered MoKa radiation. With a time constant of 4 sec. the preferred orientation of the secondary grains could be measured satisfactorily by the integrated intensities. Both (111) and (200) reflections were measured, and corresponding pole figures were constructed according to the techniques described previously.10 The agreement between results deduced from these two reflections was excellent. RESULTS AND DISCUSSION Secondary-Recrystallization Texture due to Prolonged Annealing at 1000°C. Fig. 1 shows the primary-recrystallization texture of a specimen annealed at 1000°C for 30 min. A substantial improvement in both sharpness and intensity of the cube texture, owing to the present processing method, can be noted readily by comparing Fig. 1 with similar pole figures shown earlier in Refs. 9 and 11. Secondary recrystallization

Jan 1, 1967

By Luis Toron, Salvador Cortes-Obregon

John D. Price (Colorado Fuel and Iron Corp., Pueblo, Colo)—The paper on the coal fields of the Oaxaca district as prepared by engineers Toron and Cortes-Obregon of the staff of the Bank of Mexico bears witness to the thorough and careful way in which the men associated with this organization perform their work. There is little to be added to their paper in way of discussion other than to confirm and amplify some of their statements. Since the only extensive and well-developed field of coking coal lies in the northeastern section of the country adjacent to Sabinas in the state of Coahuila, it follows that blast furnace plants would be located in that same region. Two such plants are now operating at Monterrey and Monclova, using coke produced at the Sabinas district mines. But the nearer of these two plants is 600 miles from Mexico City and even farther from the center of population. Transportation of products from these mills to the market area is therefore expensive, both because of the distance and the difficulty of the terrain over which it must be carried. The development of an integrated steel industry closer to the center of population has therefore long been a goal toward which the Mexican technicians have been striving. While the presence of coal of some grade has been reported in many of the states, and many ideas have been advanced regarding its possible uses in iron and steel production, deposits of anthracite in Sonora and the various coals of the Oaxaca district as reported on in this paper are the only ones that have been explored in a serious manner. The coking coal from the Mix-tepec zone appears to offer promise of producing a coke which could be used in a standard blast furnace. Several problems are indicated, however: 1—The ash in the coal is high as mined, but indications are that it can be washed to an ash content of 15 pct with a recovery of 70 pct of washed coal. 2—Such washing would increase the volatile content from 17.4 pct to about 20 pct, and in a byproduct oven this should give a coke yield of close to 80 pct with an ash content of coke under 20 pct. 3—A free swelling index of 5 appears low for a good coking coal, and below that of the coals from the Sabinas district, which show between 6 and 9. But washing of the coal should result in an improvement in this regard; in the United States coals from Utah with an index even lower than 5 have made a usable coke. 4—A coal with volatile as low as 17.4 in raw coal and 20 in washed coal would come close to being classed as a low-volatile rather than medium-volatile coal, and low-volatile coals are notorious for their high expansion properties. Several plants in the United States are making coke from straight medium-volatile coal of 26 to 28 volatile content, and one at Rosita,, Mexico, from coal of 25 volatile. But no plants to my knowledge are using coal as low as 20 volatile. Since the Rosita coal appears to be a borderline coal from the angle of its expansion properties the coking of one of the straight lower volatile must be approached with caution. 5—There are few coals possessing any degree of coking properties which cannot be used in coke production by careful attention to its preparation and blending. The fact that coals of other types are available in this same region make improvement through blending very possible. 6—There are other workable methods of reducing iron ore other than the conventional coke-blast-furnace method. These will not be discussed here but it is known that their use has been considered. The technicians of not only Mexico but also of the other Latin American countries are keenly aware of their natural resources and their national needs. This paper emphasizes the fact that the Mexican technicians are working on their problem and attempting to speed the day of self-sufficiency for their country. Salvatore Cortes-Obregon (author&apos;s reply)—I wish to thank Mr. Price for his kind remarks. The Mixtepec coal as shown in Table II has 30 pct ash and a free swelling index of 5, but when the same coal is washed to 15 pct ash it has a free swelling index of 8 to 9 and the volatiles increased from 17.4 to 20.7 pct. A satisfactory coke has been produced from blends made in the Mexican laboratory using at least 40 pct of the Mixtepec coking coals with the other Oaxaca non-coking coals. Koppers in Germany report good coke obtained from the Oaxaca coal with a blend of 80 pct Mixtepec coal. Consideration is being given the possibility of using methods other than the conventional blast furnace for the reduction of iron ore near the Oaxaca area; electric furnaces appear promising. The non-coking coals could be used to produce cheap electric energy and the coking coals to make metallurgical coke.

Jan 1, 1955

By G. A. Beske, P. Hilsch, J. Wulff

The effects of the growth precipitates on the su-perconduching properties of an Al- 15 al. pel Zu alloy have been studied using magneization, transition lem-perature, and residual resistivity measurements. Aging at 230C for 1/2 to 11 he produces an increase in Hfp, Ike field of first penetration, and tut increase in trapped flux. The upper critical field, Hc2 remains constant for such aging tunes. Aging at 200°C produces a decrease in Hfp and an increase in trapped flux. The transition temperature remains constant at Tc - 1.227° ± 0.02°K for aging at 220°C for tims of from 1/2 to 10 hr, and for aging at 200°C it remains constant at Tc. = 1.18° i 0.02°K for times from 1/2 hv to 26 hr. The observed behavior indicates that the superconducting matrix when aged at 220°C behaves tike a type U su-perconducior, but when aged at 200°C behares like a type I superconductor. The magnetization changes after aging can be attributed to the growth and clutnge in distribution of the precipitate in a matrix of fixed composition. IT has been realized for some time that the superconducting properties of alloys are highly structure-sensitive. This is evident in the work of Mould and Mapother1 who examined the properties of an aluminum alloy. Precipitation effects have also been briefly mentioned in other studies.2-4 Bonnin and coworkers5 have observed a sharp inc rease in trapped flux in an A1-Mg alloy when the residual resistivity reaches a value that indicates it is a type II superconductor. Recently Blanc, Goodman, and Nemoz5p have reported on precipitation effects in A1-Ag alloys. Detailed studies of precipitation in Pb-Sn and Pb-Cd alloys made by Livingston6 serve to show that the upper critical fields are enhanced by quenched-in solute. Furthermore. at various stages in the precipitation process? the upper critical field is determined largely by the remanent solute. The observed magnetic hysteresis and trapped flux in such alloys result from the interaction between precipitate and the flux filaments in the mixed state. The flux trapping appears to depend largely on the precipitate distribution and is greater if the superconductor is type II than if it is type I. To examine the effect of precipitation in another alloy system, particularly one in which the composition of the superconducting phase does not change significantly during the course of precipitation, the Al-Zn system seems interesting, especially in view of the transition temperature and resistivity studies of Chiou and seraphim.&apos; Furthermore, the recent detailed electron-microscope studies of an Al-Zn alloy by Richards and Garwood8 provide a guide for relating superconducting properties to changes in structure. For these reasons, magnetization, transition temperature, and residual resistivity measurements for varying times of heat treatment at two temperatures were made with a -15 at. pct Al-Zn alloy. The results are reported in this paper. I) EXPERIMENTAL The alloy used was prepared by Cominco Products Inc. from 99.9999 A1 and 99.999 Zn. It was chill-cast, swaged, and drawn to 0.125-in.-diam rod. The analyzed composition was 15.6 at. pct Zn (31.1 wt pct). A jeweler&apos;s saw was used to cut the 0.125-in.-diam rod into the 0.875-in. lengths needed for magnetization measurements. The ends of the cylinders were slightly beveled to remove the sharp edges. A portion of the original 0.125-in.-diam rod was drawn into 0.010-in.-diam wire and used for transition temperature measurements. Specimens were suspended from wires within a vertical furnace during heat treatment. All were homogenized at 500°C for a minimum of 3 days and subsequently solutionized for times in excess of 6 hr. The solutionizing temperature was held constant to +3°C. Individual specimens were homogenized, quenched, and aged several times and no effects indicating loss of zinc were noted. The suspended specimens were quenched by cutting the wires and allowing the specimens to fall into a silicone oil bath held at the aging temperature. They were then isothermally transforked by aging in the same bath used for quenching. After aging for the required time (approximately 10 min aging was necessary before the upper critical field reached a fixed value), they were briefly (1 to 2 sec) dipped into an acetone bath at room temperature to remove adherent oil and then immediately transferred to liquid nitrogen where they remained until inserted into the helium bath (usually within an hour). The temperature of the aging bath was held constant to +3°C for longer aging times. The cryostat used for the measurement of superconducting properties consisted of outer and inner dewars for liquid nitrogen and liquid helium, Stokes 6-in. booster diffusion pump and Stokes Model 212 mechanical pump, temperature controller to measure and control the temperature of the helium bath, and a superconducting solenoid with inserted search coils to provide the magnetic field and measure the magnetic moment of the specimens. A schematic diagram of the cryostat is shown in Fig. 1. An ultimate temperature of 0.85°K was reached with this apparatus. The temperature controller used is similar to the one described by Blake and chase.&apos; A 0.5 pct Allen-Bradley carbon resistor and a nichronle heater (200

Jan 1, 1968

By Quentin D. Singewald, B. S. Butler

Some of the broader relations between structure and ore deposition along the London fault, deduced from a thorough study of the geology of the eastern part of the Mosquito Range, should be of general interest to economic geologists. The first part of this paper is a generalized statement of the geology of the region in which the London fault is located; it may be supplemented by reference to several earlier publications by the writers and to the U. S. Geological Survey&apos;s Professional Paper 148, on the Leadville district. The second part deals with the structure of both the fault and the disturbed zone adjoining the fault. The third part discusses the salient features of the ore deposits, particularly emphasizing structural control. The two generalized maps are complementary to one another but contain too many data to show on a single small map. The London fault is between Leadville and Alma, and the ore deposits along it are said to lie in the Alma district. Field work in this district, during six summers since 1927, has been a part of the cooperative work of the U. S. Geological Survey, the State of Colorado, and the Colorado Metal Mining Board. The writers have made use of work by R. D. Butler, J. W. Vanderwilt and R. E. Landon. G. F. Loughlin and C. H. Behre, Jr., who have worked on the west side of the range, have contributed valuable suggestions. Mining men of the district have aided in many ways. General Geology Pre-Cambrian Rocks.—The oldest rocks in the district are schists, correlated with the Idaho Springs formation of the Front Range. Quartz-mica schist predominates, but other types occur locally; almost everywhere the rocks show considerable lit-par-lit injection. Intrusive into the schists are two varieties of granite, only one of which is widespread. It is a fine-grained, porphyritie, gray granite correlated with the Silver Plume granite of the Front Range. Near the head of Buckskin Gulch a

Jan 1, 1937

By Louis J. Demer, Paul A. Beck

As reported in a previous publication,1 isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: [ ] or in some cases, by the simpler relation, [ ] Here, D is the average grain size after an annealing period t. The annealing period includes the time for complete recrystallization R, and the time for grain growth [to]. DA is the grain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pct magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystallization and grain growth of the 2 pct magnesium alloy at 350°C. EXPERIMENTAL PROCEDURE The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table I and magnesium from a high purity distilled stock of magnesium crystals. [ ] Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. [ ] The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up t0 1500X, revealed a cer-

Jan 1, 1948

By J. Charles Miller

NATURAL carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inor-ganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of furnaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the produc-ing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the struc-ture. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate.

Jan 1, 1937

By Basil B. Zavoico

During 1938 the Russian oil industry, while able to increase its production 4.69 per cent above the preceding year, was not successful in correcting some of its basic difficulties, and the industry&apos;s position as it entered 1939 was unsatisfactory. The internal political difficulties of 1937 and 1938 took a toll in the oil industry as they did elsewhere in the U. S. S. R., further complicating the solution of the problems facing it, most important of which still remain: lack of experienced and responsible leadership, able to make quick decisions; undisciplined and migratory labor; and insufficient and often unsatisfactory quality of the various equipment needed by the industry and its ineffective distribution. Recent developments in the U. S. S. R. suggest that during 1939 the management will be granted more latitude and hence somewhat better results may be anticipated from the executive branch, provided, however, the "purges" do not recur. The labor should be better disciplined and should not shift as easily, owing to the introduction, at the close of 1938, of individual labor passports to all workers in the country, the principal purpose of which is to correct those two deficiencies. It is not anticipated, however, that the service of supply will show any appreciable improvement in 1939, partly because of inherent difficulties and partly because the manufacturers of heavy machinery are working primarily and necessarily for munitions. Production Production of crude oil during 1938 is estimated at 224,714,000 bbl., as compared with 212,742,000 bbl. in 1937, an increase of 4.69 per cent but 12.76 per cent below the planned output. While there were no major readjustments in the source of supply of crude oil, both the older districts, Baku and Grozny, were barely able to maintain their 1937 levels of production, the increased output being supplied primarily by the fields of Maikop and Ural Permian Basin districts. While exploration work was outstandingly successful in 1937, in 1938 no discoveries of any

Jan 1, 1939

By Basil B. Zavoico

During 1938 the Russian oil industry, while able to increase its production 4.69 per cent above the preceding year, was not successful in correcting some of its basic difficulties, and the industry&apos;s position as it entered 1939 was unsatisfactory. The internal political difficulties of 1937 and 1938 took a toll in the oil industry as they did elsewhere in the U. S. S. R., further complicating the solution of the problems facing it, most important of which still remain: lack of experienced and responsible leadership, able to make quick decisions; undisciplined and migratory labor; and insufficient and often unsatisfactory quality of the various equipment needed by the industry and its ineffective distribution. Recent developments in the U. S. S. R. suggest that during 1939 the management will be granted more latitude and hence somewhat better results may be anticipated from the executive branch, provided, however, the "purges" do not recur. The labor should be better disciplined and should not shift as easily, owing to the introduction, at the close of 1938, of individual labor passports to all workers in the country, the principal purpose of which is to correct those two deficiencies. It is not anticipated, however, that the service of supply will show any appreciable improvement in 1939, partly because of inherent difficulties and partly because the manufacturers of heavy machinery are working primarily and necessarily for munitions. Production Production of crude oil during 1938 is estimated at 224,714,000 bbl., as compared with 212,742,000 bbl. in 1937, an increase of 4.69 per cent but 12.76 per cent below the planned output. While there were no major readjustments in the source of supply of crude oil, both the older districts, Baku and Grozny, were barely able to maintain their 1937 levels of production, the increased output being supplied primarily by the fields of Maikop and Ural Permian Basin districts. While exploration work was outstandingly successful in 1937, in 1938 no discoveries of any

Jan 1, 1939

By Van Dyne Howbert, Fred E. Gray

The Presidio mine of The American Metal Co. of Texas is situated 45 miles south of Marfa, Texas, a town on the Southern Pacific R. R., and lies approximately 20 miles north of the Mexican border. Communication with the railroad is maintained over a state highway. All supplies for mine and mill are hauled in by truck from Marfa and precipitates and concentrates are freighted to the railroad by the same means and shipped to Selby and El Paso, respectively. The mill is at the town of Shafter, 1 mile from the mine and at approximately 350 ft. lower elevation. The ore is conveyed to it by an aerial tramway which requires practically no power on account of the difference in elevation. The mill is a countercurrent decantation cyanide and gravity concentrating plant of 200 tons daily capacity. Coarse and fine crushing are done at the mill. Two neal-by shallow wells in the bed of Cibolo Creek furnish an abundance of water. Power is generated for the mill and town by a Diesel engine plant. Ore Treated The ore is oxidized and siliceous. The greater part contains approximately 16 oz. of silver per ton, but mixed with this are many particles of ore of much higher grade, assaying in many instances 100 oz. or more. In the 16-oz. material there is an almost constant amount of silver which is difficult to recover by cyanidation. The high-grade material contains a much greater proportion of silver which is easily amenable to cyanide treatment. Thus, as the grade of ore becomes higher, the percentage of recovery of silver increases rapidly, under equal milling conditions. The silver minerals contained in the ore are principally argentite and cerargyrite, the former predominating The lead minerals, all of which are argentiferous, are chiefly cerussite and galena, with occasionally a little anglesite. The gold is free; most of the ore contains merely a trace

Jan 1, 1935

By AIME AIME

The following acts of the Directors are reported for the information of members:¬ At a meeting held November 3, 1905, Messrs. Henri Le Chatelier, of Paris, France, and Andrew Carnegie, of New York, N. Y., having been nominated by a large number of members, and recommended by unanimous vote of the Council, were unanimously elected Honorary Members, in recognition of their distinguished services to the arts and professions represented by the Institute. At a meeting held February 7, 1,906, Dr. James Douglas, of New York, N. Y., having been" nominated by a large number of leading members, and recommended by unammous vote of the Council, was unanimously elected an Honorary Member, in recognition of his distinguished services to the practice and the literature of mining and metallurgy, his zealous and loyal devotion to this Institute, his fraternal generosity towards professional colleagues, and his effective advocacy, by public utterance and private example, of the free communication of technical knowledge and experience. At the same meeting, By-Law IV., which now authorizes the Secretary to appoint an &apos;1 Assistant Editor," was amended by substituting the words, " Assistant with the title of Editor." At the same meeting, the resignation of Mr. Theodore Dwight, as Assistant Secretary and Assistant Treasurer of the Institute, was presented and accepted, and the Secretary was instructed to express to Mr. Dwight the thanks of the Board for his loyal and efficient services, and its regret that he could not continue in that position. . [SECRETARY&apos;S NOTE.-Mr. Dwight&apos;s resignation, dictated solely by the demands of private business, covers only his immediate management of this office. He is still a Director and Councilor, and a representative of the Institute in matters connected with the new Carnegie Building, etc.-R. W. R.] At the same meeting, the Secretary and the Treasurer reported respectively their appointment of Mr. Henry WT. B. Howard as Assistant Secretary and Assistant Treasurer, to fill

Mar 1, 1906

By AIME AIME

The following financial report of the Treasurer of the United Engineering Society is published for the information of members NEW YORK, February 15, 190S. To the Board of&apos; Trustees, United Engineering Society I beg to submit herewith the report of the Treasurer as of December 31, 1907. Your attention is called to the fact that the resources and liabilities, receipts and disbursements statements cover all the financial transactions of the United Engineering Society from its organization up to December 31, 1907. The income and expenses of operating the building during the whole operating period from December 1 to December 31, 1907, somewhat in excess of twelve months, are given. Included in the expenses, amounting in all to $52,647.11, will be found an item entitled "Building Equipment (construction account)." The expenditures under this item were not made for the operating expenses of the building, they represent a construction account, properly speaking, covering expenditures for furnishings and equipment of the building. The Founders&apos; Agreement specifically provides for this class of expenditure under the provision that the Founder Societies shall each be liable for a charge not to exceed $200,000 of principal, which shall include the land and building completed and ready for occupancy, together with the " furnishings, equipment and personal property therein." Certain details of equipment are yet to be supplied, and it. is proposed in the near future to call upon the Founder Societies for an assessment on their respective land and building funds to cover this item of building equipment. Such action would enable the item of $10,039.85 to be transferred to the income account and reduce correspondingly the assessment

Mar 1, 1908

By Edward Keller

(New York meeting, February, 1912.) IN a paper, entitled A Uniform Method for the Assay of Copper Material for Gold and Silver,1 A. R. Ledoux invited the assayers of this country to contribute to a symposium, in which the results of their assays of given samples of copper-matte and metallic copper would be made comparable. This symposium 2 appeared about one year thereafter; and through it and its discussion, first became generally known the fact that the ,gold-yield by the all-fire method of assaying is usually higher than by the so-called combination (wet and dry) method, in which nitric acid is employed as a solvent for the copper. In the publication alluded to, the supposed cause of gold-losses in the latter method was declared to be the solvent action of copper nitrate, or of the reduction-products of the nitric acid, upon the gold. Up to a very recent date, gold has been held to be insoluble in pure nitric acid. (The solvent action of any chlorine present in the nitric acid must here properly be disregarded as belonging in the realm of carelessness. Among later allusions to this topic, W. R. Tan Liew 3 ascribes the solution of the gold in the combination-assay entirely to the action of nitrous acid at the high reaction-temperature of copper and nitric acid ; F. B. Flinn 4 a believes the low result in gold to be due exclusively to mechanical losses-finely-divided gold penetrating through the filter-paper-but presents no experimental data confirmative of this belief; and 0. Pufahl 5 attributes the solubility of the gold in some coppers to the presence of selenium-a view which appears to be shared by many as- 1 Trans., xxiv., 575 (1894). 2 Trans., xxv., 250 (1895). 3 Engineering and Mining Journal, vol. lxix., No. 16, p. 469 (Apr. 21, 1900). 4 Engineering and Mining Journal, vol. lxxxvii., No.11, p. 569 (Mar. 13, 1909). 5 Lunge, Chemische Technische Untersuchungs Methoden, vol. ii., p. 229 (1900).

Jul 1, 1912

By John Hays Hammond

This is an era of " expansion; and, conformably with the change in commercial conditions, the function of the mining engineer, as well as that of his confreres in many other professions, has also expanded. From the position of an engineer, limited to the determination of technical questions, the engineer of to-day has come to assume an economic importance in those branches of industry dependent upon engineering skill for their development. He is indeed an engineer of limited usefulness who does not go further professionally than to submit a purely technical report on subjects presented for his consideration. While he has the same responsibility as formerly in the solution of the technical problems involved, he is further expected to supplement his report with advice on the financial and commercial aspects of these problems. For the great majority of problems presented to the engineer ultimately involve the determination of the pecuniary, relations of the propositions under consideration. The great corporation lawyer no longer earns his fee by merely submitting his opinion as to the legal issues involved in law-suits affecting the corporation; he now assumes charge of the entire legal work, including both the organization of the corporation and the maintenance of its legal status thereafter. In like manner, the engineer, whose report was, as I have said, formerly confined to the determination of the geological and other cognate features of a mining enterprise, is now expected, not. only to embody information on these subjects in his report, but also to give his opinion whether the property offered for sale in pursuance of such an enterprise is worth the price asked for it. Moreover, if he recommends the purchase of a property, he incurs a certain moral responsibility for its efficient manage-

Nov 1, 1908

By Carl H. Beal, E. D. Nolan

In February, 1918, the conclusion was published by Lewis and Beal "that wells of equal output on the average will produce equal amounts of oil in the future, regardless of the ages of the wells." This conclusion was based upon the study of data collected principally in Oklahoma and was not known at that time to be true for other oil fields. An abundance of statistical proof was later collected by the senior author of the present paper, which showed that the conclusion was undoubtedly well founded and that it applied to other fields as well. Accordingly, it was later restated2 as the "law of equal expectations" as follows: "If two wells under similar conditions produce equal amounts during any given year, the amounts they will produce thereafter, on the average, will be approximately equal, regardless of their relative ages." Although only scanty data from the California oil fields were available at the time this publication was prepared, sufficient information was analyzed upon which to base the insert on Fig. 80, which showed beyond a doubt that the law held at least for a part of the Midway oil field in California. Recently the authors have collected more complete data in California, and it is the purpose of this paper to explain the method used in demonstrating the truth of the law and, in addition, to give several methods by which curves constructed in accordance with this law can be used in a practical way with ease and accuracy. The Family Curve The law of equal expectations means that each individual of a group of wells producing under similar conditions will decline along approximately the same type of curve, the rapidity of decline varying with the output

Jan 1, 1921