Search Documents

By Richard W. Lodge

Mr. H. R. Batcheller, of the class of 1894, Massachusetts Institute of Technology, while experimenting with chlorine gas on a certain lot of roasted concentrates, met with the following difficulties: 1. A poor extraction of the gold. 2. A very large consumption of chlorine gas. 3. Inability to precipitate all of the gold from the solutioil containing the AuC1,. 4. The bullion obtained was very base. These difficulties were the same whether the chlorine was generated from H2SO47 MnO29 and salt, or whether H2SO, and bleaching powder were used. They may be accounted for partly by the presence of some arsenic left in the roasted ore, and partly by the presence of copper in the solution containing the AuCI3. It was therefore suggested to try the effect of bromine on a similar lot of ore. The use of this element is, of course, nothing new, but in the following experiments it seemed to present many advantages over chlorine. The material worked upon consisted of some concentrates containing 2.31 ounces of gold per ton, and 34.26 per cent. of arsenic, which would correspoild to about 74.4 per cent. Of

Jan 1, 1896

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and requires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged because a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced. Difficulties sometimes encountered in continuous filter operation can be summarized in the following four categories: 1) Low filtration and/or washing rates due to blinding of the filter medium. 2) Poor cake discharge resulting from sticky cakes, filter medium blinding, or too thin a cake for the particular type of filter. 3) High filter media costs caused by short life and frequent down times for cloth changing. This results from blinding or from abrasion by the scraper blade when cakes are thin. 4) Blowback of filtrate at cake discharge because not enough air passes through the cake to purge the drainage area and filtrate lines during dewatering. To reduce or eliminate blinding tendencies several modifications have been tried, for example, cover-cleaning showers, blowback under the feed slurry, and snap-blow cake discharge. In many cases, however, this simply retards the rate of blinding, since the filter medium is kept clean at its outer surface only by these methods. As blinding usually occurs within or on the back of the medium, the operator is finally forced either to remove the cloth and scrub the medium intensively with a cleaning solution or acid-rinse it on the filter—all resulting in down time, short cloth life, and additional costs.

Jan 1, 1959

By C. E. Corson

THE experiments of which the results and significance are set forth in this paper do not by any means cover the whole subject of the heat-treatment of the material referred to, yet they constitute a contribution to that general subject, rather than to the special department of annealing. The material here considered is acid open-hearth steel, containing from 0.50 to 0.80 per cent of carbon, with a nearly uniform percentage of other elements. This class of steel is rapidly increasing in commercial importance. It is even rumored that the rail-specifications of some railroads will hereafter require open-hearth steel. Yet this particular grade seems to have received less study and description from the standpoint of the metallographist than many others. The investigation here described was directed to the following points:-Steel containing about 0.50 per cent, of carbon : 1. The structure as related to the temperature, at the same rate of cooling; 3. The structure and physical properties as related to temperature at different rates of cooling; 3. The structure and physical properties as related to different finishing-temperatures and different rates of cooling; 4. The bearing of these observations upon the statement of Prof. Albert Sauveur.1

Sep 1, 1906

By R. G. Bentsen, D. A. T. Donohue

The cyclic steam injection process has become the most widely applied and most successful thermal recovery technique in use today.1-4 Normally, steam stimulation is repeated several times during the life of a project. The problem is to select the optimum number and size of steam treatments so that the profits realized over the entire life of the project are maximum. Obviously, operating costs rise directly with the frequency and amount of steam injection. Operating efficiency, on the other hand, can be adversely affected if the amount and frequency of stimulation are insufficient. Thus arises a multistage decision problem; that is, a decision must be made at each sub-period (day, for example), as to whether steam should be injected, and, if so, how much. It is desirable that these decisions be made in such a way as to secure maximum net profit before taxes. This can be achieved by dynamic programming. To use dynamic programming, we must be able to predict not only the production rate-time curve resulting from a given stimulation, but also how changes in stimulation policy will affect this curve. In this study, the effect of steam injection on well performance is estimated on the basis of a simple model that takes into account both steady-state and transient flow. Oil production rate is calculated for both types of flow, and the larger of the two values is used. This allows the calculation to change to radial steady-state flow at such time as this mechanism becomes more effective than the transient mechanism. We propose to show how dynamic programming can be used to optimize the steam soak process with respect to net profit. For this, a mathematical representation of the steam soak technique is necessary. A further objective, therefore, is the formulation of a mathematical model capable of realistically simulating the physical process. Oil Production Response Model The advantage of using a mathematical model is its generality and ease of manipulation. However, the model must be an accurate representation of the physical process, for a solution derived from a model can be no better than the model itself. The question now arises as to how well the model should be expected to simulate reality. In general, the simplest model should be tried first, for additional accuracy is apt to require additional cost and time. Also, the search for a high degree of accuracy may yield only greater complexity and difficulty without yielding significantly better results. With this in mind, we kept our model as simple as possible, yet generally representative of the actual physical process. The number of state variables is limited to three, and stochastic variations in the parameters are ignored. As a consequence, use of this model should be restricted to cases in which the underlying assumptions are not severely violated. In

Jan 1, 1970

By L. F. Pett

ALTHOUGH Kennecott's orebody has long been outlined, it is still necessary to define further its limits. This mine, long an advocate of churn drill methods, recently supplemented its practice by using a diamond drill. So far, the diamond drill holes have been along the main canyon floor which traverses the mine area. This zone, highly fractured, is cut by numerous friable quartz veinlets encountered within the porphyry. These veinlets, formed by filling contracted porphyry fractures with hot, siliceous, mineral-bearing solutions, are often more highly mineralized than adjacent porphyry. They pulverize on contact, yielding only slight amounts of core. For this reason neither analysis of core recovered (amounting to 37.5 pct of approximately 10,000 ft of hole drilled) nor sludge analysis considered separately would give correct assays. The following equation has been adopted: actual weight theoretical actual weight core — theoretical weight sludge Drilling is done un.der contract. Collection of core and sludge samples together with double-checked assaying is done by the company. Microscopic, specto-graphic, and X-ray examination of rock specimen saved is carried on at the University of Utah. A fund, set up by Kennecott Copper Corp. at the University, has encouraged cooperation in solution of mining research problems. The drill used is a Longyear hydraulic powered by a Waukesha 26-hp gasoline motor. A pump, Bean Royal type, is powered by a 7-hp Briggs-Stratton gasoline motor. Weight of unit is 4000 lb and is placed under tripod of 35-ft wood poles within a 25-ft sq area. The following results have been attained: Avg depth of hole drilled, ft 1215 Avg drilling depth per 8-hr shift, ft 10.11 Core Size, In. Avg depth of NC casing, ft 21 2 11/16 Avg depth of NX casing and size core, ft 178 2Ye Avg depth of BX casing and size core. ft 427 1% Avg depth of AX casing and size core, ft 585 1 5/32 Through the use of metal sludge collection boxes, 12 ft long, 18 in. wide, and varying from 12 to 24 in. in depth, sludge recovery has been maintained above 95 pct. Samples, both core and sludge, are assembled for each sample interval and averaged in 50-ft bench increments. Determinations for mineral values are made at both the mine and mill. Assay results varying in excess of 0.05 of copper assay values are rerun to determine correct assay. The organization chart for the Kennecott Utah copper mine is shown in Fig. 1. The Utah mine requires approximately four men per shovel shift to drill solid rock, properly slope banks, and trim loose material from the top of bench sections in making them safe for men and equipment working below. During recent years, while the mine has been worked day and night, powder crews have worked day shift only. Series of toe holes drilled back of advancing electric shovels comprise approximately 70 pct of all mine drilling. These holes, spaced about 21 ft apart, have a depth of 24 ft. Of the footage drilled, 25 pct is for vertical holes either 24 or 28 ft deep, spaced about 28 ft centers along the top rim of banks. This combination of toe holes, using an Ingersol-Rand DA 35 drifter mounted on a tripod and the vertical holes using an Ingersol-Rand Type X71 wagon drill is standard practice above the pit elevation. These benches are 68 ft high, with a few exceptions, while benches below the pit elevation are 50 ft high and require very little drilling other than toe holes. Five benches, varying in height from 80 to 100 ft, require a combination of toe holes plus vertical holes and bank holes or electric churn drill holes. Bank holes using the DA 35 drifter and electric churn drill using Bucyrus-Erie Model 29T, account for 5 pct of feet drilled. Until the past year, drilling of fill material on upper levels was accomplished by churn drill method. Wagon drills are now used for fills because they can be set up and drill a hole an hour. It is necessary to run an air drill 7 hr for each 8-hr shovel shift. Average drilling rates during the past year were as follows: DA 35 drifter using 2 and 3-man crews — 4.36 ft per man hr X 71 wagon drill using 2-man crews — 6.45 ft per man hr DA 35 drifter bank holes, 3-man crews — 2.53 ft per man hr Bucyrus-Erie churn drill, 2-man crews —1.9 ft per man hr Total mine avg — 4.57 ft per man hr Mine practice assigns powdermen to job locations where they perform all drilling and blasting work within the area. Almost as much labor is consumed in springing and loading holes as in drilling them. Average powder consumption is approximately as follows: Per Electric Shovel Shift, Lb To spring and chamber holes — 50 Blasting — 500 Trim banks — 50 One fifth of all powder used is Hercules hercomite bag powder while four fifths is Hercules gelamite 65 pct strength in 1 Vi in. x 8 in. sticks. Frozen material, overhanging from top banks, creates a winter hazard to shovel operators and equipment. Experiments are being conducted with a high-speed Hercules powder in an effort to eliminate this condition. Banks are trimmed by powdermen who lodge 8 or 10 bundles of powder, containing 15 or 20 sticks each, across the upper surfaces of each working face. To each bundle of powder is attached a primer with 6-ft fuse which is lighted as the powdermen, who have lowered themselves down the bank on ropes, ascend to safety. Three angle dozers, D8 caterpillars, make grades and move supplies for the average 31 drilling machines working daily. Compressed air is furnished by three Ingersol-Rand compressors, each with rated capacity of 3750 cu ft of air per min at 100 lb reservoir pressure.

Jan 1, 1952

By E. H. Mohr

At the McGill concentrator of the Nevada Consolidated Copper Co., all flotation operations have been carried out in Forrester cells since November, 1926. In respect to cost of operation, the new cell has proved to be superior to the Callow, which it supplanted, and its incorporation in the flow sheet has resulted in a marked improvement in the metallurgy. Before citing the advantages of the new machine over the old, it should be explained that the Forrester has not only replaced the Callow, but it has made possible the elimination of a number of tables as well. When Callow cells were in use, table concentration preceded flotation. The ball mill pulp was elevated, by means of air lifts, to roughing Wilfley tables situated two floors directly above the flotation floor. On an intermediate floor were additional tables which cleaned the concentrate from those above. The finished table concentrate constituted approximately 60 per cent. of the total mill production, and contained about 40 per cent, of the recovered copper. The table tailings were returned to the classifiers, the overflow from which went to the flotation cells and the oversize to the ball mills. As soon as the Forrester cells were installed, this tabling operation was discontinued. The ball mill pulp now discharges into the classifiers direct, without the intermediate tabling. It was impracticable to ernploy the present flow sheet when Callow cells were in use, for the reason that unless the great,er part of the heavy mineral was first removed, it accumulated on the mats and adversely affected the flotation operation. By tabling ahead of flotation, it was practicable to maintain the concentrator at 10 to 20 per cent. greater capacity (depending up on the pyrite contnt of the ore) than was possible by flotation alone. This was due to the necessity for finer grinding in the latter case. Even though the table conecntrates contained only 6 to 8 per cent'. copper content, the low smelting costs made it advantageous to operate at high mill capacity, at the cost of low grade of product. Standard Section equipment With the old flow sheet, a standard section consisted of four ball mills and classifiers, one air. lift, 20 roughing tables, 10 cleaner tables, 12 primary

Jan 1, 1928

By Robert H. Richards

(Pittsburg Meeting, March, 1910.) THIS is in part a review paper, indicating the various steps that have been taken in developing hindered-settling apparatus, some of the standard data that have been obtained, and some of the conclusions one is led to as to the effect of it in improving concentrating-methods and machinery, and in part it brings in some unpublished work. CAUSES OF LOSS IN ORE-CONCENTRATION. In making a study of the separation of valuable minerals from the waste gangue, particularly by water concentrators, it is necessary to define, first of all, what are the causes of-loss that are likely to interfere with the concentration. Having made this definition; we can then study to see in what way the machines make their losses, and plan remedies for them in an intelligent way. Losses may be stated to occur as included grains, as flat or long grains, as fine free mineral, and as absolute slime. We will take, these up one by one, as follows: Included Grains.-Fig. 1 shows by a set of diagrams how included grains may occur: first, where the heavy mineral grains attached to the quartz are of large size; secondly, where they are of small size ; and thirdly, where very fine particles of heavy mineral are included in the quartz. We have to decide in regard to included grains whether they are rich enough to go direct to, the furnace, or poor enough to throw away, or whether they lie between these two points and require recrushing as the only means of severing the values from the waste. This last case is the only one requiring special treatment at our hands. We will therefore consider that next. * By mutual consent, this paper has been presented also before the Colorado Scientific Society, and the Canadian Mining Institute, Montreal.

Feb 1, 1911

By L. J. Health

Synthetic rock with predictable porosity and permeability has been Prepared from mixtures of sand, cement and water. Three series of mixes were investigated primarily for the relation between porosity and permeability for certain grain sizes and proportions. Synthetic rock prepared of 65 per cent large grains, 27 per cent small grains and 8 per cent Portland cement, gave measurable results ranging in porosity from 22.5 to 40 per cent and in permeability from 0.1 darcies to 6 darcies. This variation in porosity and permeability was caused by varying the amount of blending water. Drainage-cycle relative permeability characteristics of the synthetic rock were similar to those of natural reservoir rock. INTRODUCTION The fundamental behavior characteristics of fluids flowing through porous media have been described in the literature. Practical application of these flow characteristics to field conditions is too complicated except where assumptions are overly simplified. The use of dimensionally scaled models to simulate oil reservoirs has been described in the literature. 1-3 These and other papers have presented the theoretical and experimental justification for model design. Others have presented elements of model construction and their operation. In most investigations the porous media have consisted of either u ncon soli da ted sand, glass beads, broken glass or plastic-impregnated granular substances—materials in which the flow behavior is not identical to that in natural reservoir rock. The relative permeability curves for unconsoli-dated sands differ from those for consolidated sandstone. The effect of saturation history on relative permeability measurements is discussed by Geffen, et a1.4 Wyga15 has shown quite conclusively that a process of artificial cementation can be used to render un consolidated packs into synthetic sandstones having properties similar to those of natural rock. Many theoretical and experimental studies have been made in attempts to determine the structure and properties of unconsolidated sand, the most notable being by Naar and Wygal.6 Others have theorized and experimented with the fundamental characteristics of reservoir rocks. This study was conducted to determine if some general relationship could be established between the size of sand grains and the porosity and permeability in consolidated binary packs. This paper presents the results obtained by changing some of the factors which affect the porosity and permeability of synthetically prepared sandstone. In addition, drainage relative permeability curves are presented. EXPERIMENTAL PROCEDURE Mixtures of Portland cement with water and aggregate generally are designed to have certain characteristics, but essentially all are planned to be impervious to water or other liquids. Synthetic sandstone simulating oil reservoir rock, however, must be designed to have a given permeability (sometimes several darcies), a porosity which is primarily the effective porosity but quantitatively similar to natural rock, and other characteristics comparable to reservoir rock, such as wettability, pore geometry, tortuosity, etc. Unconsolidated ternary mixtures of spheres gave both a theoretically computed and an experimentally observed minimum porosity of about 25 per cent.7 By using a particle-distribution system, one-size particle packs had reproducible porosities in the reproducible range of 35 to 37 per cent.6 For model reservoir studies of the prototype system, a synthetic rock having a porosity of 25 per cent or less and a permeability of 2 darcies was required. The rock had to be uniform and competent enough to handle. Synthetic sandstone cores were prepared utilizing the technique developed by Wygal.5 Some slight variations in the procedure were incorporated. The sand was sieved through U. S. Standard sieves. A 18-20 sand denotes that the sand passed the Number

Jan 1, 1966

By H. Linder, W. H. Dennen

The graphitic carbon content of soils may be used to detect and delimit subsurface graphitic zones. Spectrographic measurement of carbon in C horizon soils from several areas in the northeastern United States shows good correlation with known graphitic bodies. Bodies of graphite and sulfides are readily located by electromagnetic prospecting methods, but these methods cannot generally discriminate between them. Usual practice, therefore, requires follow-up work on electrically anomalous areas by trenching, drilling, or soil sampling in order to determine the mineralogical nature of the conductor. The efficiency and cost of such follow-up is consequently an important factor in prospecting. The presence of buried sulfide deposits is often reflected in concentrations of metals in the superincumbent soil. Simple chemical tests for such metal concentrations have been developed and applied with considerable success. Bodies of graphite or mixtures of graphite and sulfides are, however, very common and a means whereby buried graphite could be detected by soil testing should provide valuable additional information in the search for ore sulfide and graphite deposits. Graphite is a notably stable substance and should persist in soil above graphite-rich horizons. Microscopic examination of soil samples high in carbon, however, failed to reveal any recognizable graphite fragments indicating a grain size in the clay range. Presumably such small particles would have some mobility in a soil by a translocation mechanism similar to that proposed for the movement of clay particles in a soil profile. Experimental data supports this idea since the boundary between background and anomalous soils carbon values is quite sharp, but the anomalous zone is slightly broader than the graphitic source rock. A simple spectrochemical technique for the determination of carbon in geological materials has been described by Dennen,1 and may be directly applied to soils. A modification of this technique which employs an arcing chamber through which nitrogen is passed is recommended to decrease contributions from atmospheric carbon dioxide. Tests indicate that soils over graphitic zones may be strongly enriched in carbon. The spectrochemical determination of carbon depends upon the formation of the cyanogen molecule (CN) from carbon in a sample and atmospheric nitrogen, under the high temperatures associated with a dc arc. Samples for analysis are dried, lumps broken, and screened. A small portion of the -100 mesh fraction is packed into a copper electrode and excited as the cathode of a dc arc. The band spectra of cyanogen are recorded photographically and the density of the bandhead CN 3883A is measured. The limit of detection of the method is about 0.01 pct C and its coefficient of variation is about 15 pct. Soils, of course, contain carbon in other forms than graphite, and the amount of interference from such sources was examined. The C horizon of several soils from Massachusetts, Maine, and Pennsylvania were found to have a carbon content of 0.3 to 0.5 pct by weight. This content is chiefly due to the presence of carbonates and vegetable matter in the sample and may be readily eliminated, or at least

Jan 1, 1961

By John Jermain Porter

(San Francisco Meeting, October, 1911.) THE value of any particular ore, coke, or limestone, for iron-making, depends upon its effect, first, upon the quality or value of the resultant product; and second, upon the cost of smelting. The factors under the first head are the percentages of phosphorus, manganese, and other elements, which remain in the pig-iron ; while those under the second head are the percentages of iron, carbon, or lime, the slag-forming constituents, which must be fluxed, and any other ingredients which give rise to variations in cost of fuel and flux. The first of these criteria of value is perhaps not capable of being reduced to a general formula embracing all cases, since it must vary to a great extent with market-fluctuations. For example, Bessemer pig is worth sometimes more and sometimes less than foundry-pig ; and the premium paid for high manganese varies within wide limits. The second, or smelting-value, however, can be expressed numerically with a fair degree of accuracy; and it is with this phase of valuation that the present paper is concerned. The utility of a means of comparing numerically the relative smelting-values of different ores, cokes, and limestones, is self-evident, although it may not have importance in Northern practice, where materials are largely standardized. On the other hand, there are, especially in the South, many furnace-managers who must use a great variety of materials of widely varying grade; and it is with special reference to this district, and in connection with the efficiency-methods which I have elsewhere proposed,1 that the methods herein described were devised.

Mar 1, 1912

By E. H. Mohr

AT the McGill concentrator of the Nevada Consolidated Copper Co., all flotation operations have been carried out in Forrester cells since November, 1926. In respect to cost of operation, the new cell has proved to be superior to the Callow, which it supplanted, and its incorporation in the flow sheet has resulted in a marked improvement in the metallurgy. Before citing the advantages of the new machine over the old, it should be explained that the Forrester has not only replaced the Callow, but it has made possible the elimination of a number of tables as well. When Callow cells were in use, table concentration preceded flotation. The ball mill pulp was elevated, by means of air lifts, to roughing Wilfley tables situated two floors directly above the flotation floor. On an intermediate floor were additional tables which cleaned the concentrate from those above. The finished table concentrate constituted approximately 60 per cent. of the total mill production, and contained about 40 per cent. of the recovered copper. The table tailings were returned to the classifiers, the overflow from which went to the flotation cells and the oversize to the ball mills. As soon as the Forrester cells were installed, this tabling operation was discontinued. The ball mill pulp now discharges into the classifiers direct, without the intermediate tabling. It was impracticable to employ the present flow sheet when Callow cells were in use, for the reason that unless the greater part of the heavy mineral was first removed, it accumulated on the mats and adversely affected the flotation operation. By tabling ahead of flotation, it was practicable to maintain the concentrator at 10 to 20 per cent. greater capacity (depending up on the pyrite content of the ore) than was possible by flotation alone. This was due to the necessity for finer grinding in the latter case. Even though the table concentrates contained only 6 to 8 per cent. copper con- tent, the low smelting costs made it advantageous to operate at high mill capacity, at the cost of low grade of product. STANDARD SECTION EQUIPMENT With the old-flow sheet, a standard section consisted of four ball mills and classifiers, one air lift, 20 roughing tables, 10 cleaner tables, 12 primary

Jan 1, 1928

By R. W. Stahl

Employees and dollars are necessary to all enterprises and any force, such as fire, which destroys either, can bring very serious consequences, including business failure. Since everyone acknowledges the necessity of conserving human life, we will devote most of our paper to the economic factors involved. A coal-mine fire is considerably more difficult to combat than a fire in a surface building because of the combustible surroundings in the mine, the explosive gases emitted from the coal, the suspension of explosive dust when mine timbers burn and the unsupported roof falls, the limited space in which approach to the fire can be made, and the limited avenues of escape. A survey of coal-mine-fire protection indicated that a rather low value was being placed on property and equipment. This prompted comparison with other industries. The comments made in this comparison are not intended as an indictment of the coal industry, since we do have mines that are well protected against fire, but the comments on conditions at the mines visited are factual and may help others to improve similar conditions. SURVEY PROCEDURES Plants of the steel, aluminum, rubber, chemical, and petroleum industries were surveyed, and all facets of the fire-protection scheme were covered. The industrial plant invariably had four times as much water readily available for instant use than the mine. In many mines where water is available, no equipment for applying it is provided, such as hose, nozzles, and adapters, so that time is lost in collecting this equipment. (See Table I.) EXTINGUISHERS Many more and generally larger portable extinpishers are available at the plant as compared to the mine. The extinguishers are generally placed nearer to sources of danger. In addition, respiratory protective equipment is always available at strategic points in plants but only in a few mines. (See Figs. 1 and Table 11) INSPECTING AND TESTING EQUIPMENT Plant water facilities are checked weekly and flushed at 6-month intervals, and hose is pressure-tested at least yearly; some mines check water yearly, but hose is not tested unless used. Fire extinguishers are inspected weekly in plants and completely overhauled yearly; one mine had monthly checks and overhauls only after use. FIRE BRIGADES AND TRAINING Every plant had designated fire-fighters and some complete full-time brigades; at one mine a chief mechanic was designated as being in charge of fires, and other depended entirely upon officials who might not be familiar with the equipment. COST OF FIRES AND PERCENTAGE OF CAPITAL INVESTMENT IN FIRE PROTECTION The direct cost of recent mine fires ranged from $128,000 to $240,000; indirect costs, such as lost tonnage, idled equipment, lost orders, and the like might run the cost to over $500,000. (See Figs. 2 and 3).

Jan 1, 1961

By AIME AIME

The Washoe plant, 1 in Anaconcla. Mont., together with the local street-railroad, ranches a. foundry and machine-shop a brick-plant and the Montana hotel, form a property under one management; to which should be added the mines in Butte owned by the company, from which part of the ore-supply of the plant comes. The Anaconda Copper Mining Co., controlled by the Amalgamated Copper Co., was reorganized under the laws of Montana in 1893. A map of the plant, showing the numerous departments and illustrating the details of tracks, pipe-lines, and charging-stations for compressed-air locomotives, is given in Fig. 1.

Jul 1, 1906

By K. A. Grange, W. S. Holt, E. T. Tkac

Quantitative knowledge of the time clement involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 13s-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Aeaand Ae,), the temperature range of martensite formation, and the end-quench harden-ability. These data are directly applicable to the hcat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. Material All specimens were prepared from a 1 1/4 i-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: AIn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, I.j7: Mo, 0.36: All 1.26. The forged bar was normalized from r750°F (95s°C) and then tempered for one hour at rzoo°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. Equilibrium Transformation Temperatures In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Aep, and the maximum temperature at which austenite is completely unstable, Ael, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1948

By W. S. Holt, K. A. Grange, E. T. Tkac

Quantitative knowledge of the time clement involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 13s-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Aeaand Ae,), the temperature range of martensite formation, and the end-quench harden-ability. These data are directly applicable to the hcat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. Material All specimens were prepared from a 1 1/4 i-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: AIn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, I.j7: Mo, 0.36: All 1.26. The forged bar was normalized from r750°F (95s°C) and then tempered for one hour at rzoo°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. Equilibrium Transformation Temperatures In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Aep, and the maximum temperature at which austenite is completely unstable, Ael, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1948

By Wm. C. Madge, H. P. Allen

The chloridizing mill of the Standard Reduction Co. is located about 75 miles south of Salt Lake City on the Tintic branch of the Denver & Rio Grande Western R. R. and 12 miles from the Tintic Standard mine. The daily capacity is 200 toss of a siliceous, low-grade, silver-lead ore from this property. It has operated continuously since it was started in January, 1921. The process consists essentially of a chloridizing roast followed by a percolating leach with a nearly saturated solution of common salt, acidified with sulfuric acid, the precipitation of silver on sponge copper and of copper and lead on tin-plate cuttings. The precipitates are shipped to a smelter. Some of the general ideas involved are said to have been used by Augustin in England, in 1840. A number of textbooks treat of the subject, especially the chloridizing roast followed by a leach with sodium hyposulfite or amalgamation. The process was revived in this district by Theo. P. Holt, N. C. Christensen, the Bureau of Mines, and others. Nature of Ore Treated The average assay of the ore treated during 1924 is as follows: Gold, ounces per ton...................................... 0.025 Silver, ounces per ton..................................... 18.26 Copper, per cent......................................... 0.30 Lead, per cent........................................... 5.00 Silica, per cent........................................... 65.00 Iron, per cent............................................ 10.00 Lime, per cent........................................... 0.70 Sulfur, per cent.......................................... 3.00 Arsenic, per cent......................................... 0.70 The silver is finely disseminated and occurs as native, combined as a sulfide and, to a very small extent, as the chloride. The lead may be present as carbonate, sulfide, or sulfate.

Jan 1, 1926

By F. C. Foshag, P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corp. operates a modern coal preparation plant in Van, WV. Since start-up of the Van plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miners' vacation, the original system - which included two screw conveyors and a drag conveyor - was replaced by an installation using two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance.

Jan 1, 1983

By E. A. Anderson

In 1918 the American Society for Testing Materials held a symposium2 on what was then known as season cracking. The sessions included six papers, all on brass. During the ensuing 26 yr., many new workers have come into the field and several other metals have been found subject to failure by stress-corrosion cracking when the right combination of stress and environment is achieved. It is not surprising, therefore, that the present symposium has brought forth 29 papers covering alloys of seven important metals. The phenomenon of stress-corrosion cracking is not necessarily confined to these seven metals. Dix3 has stated, "Indeed, it is probable that ingenious investigators can find solutions which will stress-corrosion crack any known metal or alloy." Mears, Brown, and Dix4 have indicated that stress- corrosion cracking failures are not necessarily limited to metals but may include the plastics. It is to be expected that the increase in the number of metals known to crack in service and the general emphasis on such failures at a symposium such as this will alarm many to whom the subject is un- familiar. Such alarm is not justified by the record. It is true that stress-corrosion

Jan 1, 1945

No. 264. A long established company operating steel and iron foundries, machine and forge shops, whose varied products are sold to the Government, railroads, mining and contracting industries, etc., has, openings in both manufacturing and selling departments for men with technical education and experience who are not subject to military call. State full particulars, kind of position preferred and salary expected. No. 265. Young man wanted, technical graduate preferred, to superintend construction f a small charcoal blast furnace. Man with blast-furnace experience preferred. For the right kind of man this is, not only a permanent job but an opportunity. In writing, give full particulars as to age, education, experience, salary wanted, etc. No. 26.6. An important copper mining and smelting company in Arizona needs two or three metallurgical chemists, at salaries. ranging front $150 to $175 per month. No. 267. A consulting mining engineer needs two superintendents for developing chrome deposits near Philadelphia; and another technical man for other engineering work in the same vicinity. No. 268. An iron-mining company, in New York State needs a mining engineer with knowledge of geology and acquaintance with construction work; A married man, with about 10 years' engineering experience preferred.

Jan 2, 1918