Search Documents

By Reuel A. Cochrane, Harry H. Angst

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By Hiroshi Kato, Shin’ichi Nagashima, Hiroshi Takechi

The preferred orientations detleloped during cold rolling, annealing, and hot rolling of low-carbon steel sheets have been investigated by means of an inverse pole figure technique. And X-ray line profile meas-urerrlents were made for the study of the factor which causes the textural changes between cold-rolled and recrystallized sheets. From ND (sheet normal divection) and RD (rolling direction) inverse Pole figures tlze axis detisity change with increasing cold reduction was measured and the Preferred orientations were analyzed. These results can be explained by crystal rotation due to slip during rolling deformation. The ND axis density change during annealing of cold-rollitig sheets is contrary to the change observed in the case of rolling. It was found that the orientation dependency of stored strain energy resulting from cold rolling apparently corresponds to the textural changes during recrystallization. The texture in hot-rolled sheets was found to be influenced by finishing tenlperatltre. In a sheet kol-rolled below the Ar, temperature a significant differernce in texture between the surface and central layers was obtained, the former having {hkl}(111} and {110 )(uvw) orientations and the latter having {pqr}( 110) orientation. A large number of investigations1 6 have been made on the textures of iron and low-carbon steel sheets, and, since it was shown7 13 that preferred orientations are closely related to deep drawability of steel sheets, studies14" 7 on the influence of production processes upon textures have been made from the standpoint of industrial interest. Generally, the textures in low-carbon steel sheets have several components of preferred orientations, but the overlapping of poles makes it difficult to analyze texture quantitatively from pole figures. On the other hand, an inverse pole figure directly expresses quantitative values of components of preferred orientations as the density of a certain sample axis with respect to the crystallite coordinates. Such a texture representation is desirable for a study of deep drawability. The purpose of the present work is to use both inverse and conventional pole figures, with emphasis on the former, to clar~fy the textural changes ~n low-carbon steel sheets by the production processes of hot rolling, cold rolling, and annealing. And the factor causing the textural changes during annealing is studied using an X-ray diffraction line profile technique. EXPERIMENTAL PROCEDURE Sheet specimens for study of cold rolling and annealing textures were taken from a hot-rolled strip of rimmed steel 2.7 mm thick. The chemical composition is shown in Table I. Although the study of cold-rolling textures requires a suitable material with random orientation, it is difficult to produce a perfect random one. But the used specimens, obtained from the hot-rolled strip with a finishing temperature higher than Ar3, were nearly random, such as shown in Fig. 15. These were cold-rolled to various reductions by a 4-high rolling mill with 150-mm-diam work rolls and 300-mm-diam backup rolls. The influence of hot-rolling conditions such as finishing and coiling temperatures on textures of hot-rolled strips was studied. The chemical compositions of these hot coils are given in Table I1 and the hot-rolling conditions are given in Table 111. inverse Pole ~i~ure -~easurement. Two methods for determining inverse pole figures with high precision have been proposed. The first, by Jetter et a1.,18 consists of obtaining mean densities of divided regions in a unit stereographic triangle by solving simultaneous linear equations to approximate the integral relation between conventional and inverse pole figures. The second, proposed by ~oe'~-'~ and Bunge,22'23 consists of determining an expanded series of spherical surface harmonics which express axis densities from several sets of pole distribution data. Both methods require laborious numerical calculations which make them unsuitable for practical use. However, the axis densities of the locations corresponding to low Miller indices in a unit stereographic triangle can be obtained

Jan 1, 1969

By A. H. Willis

In this paper the results of an exploratory study conducted by personnel of the Knolls Atomic Power Laboratory on 18.6, 22, and 40 wt pct uranium-zirconium alloy will be presented. LARGE power output and long life or endurance from small, compact nuclear reactors require the use of enriched uranium for a fuel material. However, the ability to remove heat from the element, the tolerable fission product concentration, or some physical limitation of the system can limit the allowable fuel enrichment, or the volume of the fuel. In such an event, the fuel-element designer must find a suitable diluent for the uranium. Zirconium is an attractive material for such a purpose as it has good nuclear properties and a low absorption cross section. Because it has a good corrosion resistance in water, zirconium is a suitable cladding and the uranium-zirconium alloy makes a good core material. The alloy has a high thermal conductivity, a low elastic modulus, and a low thermal-expansion coefficient, all of which tend to minimize the thermal stresses in the core. Furthermore, the unirradiated material is reasonably ductile and has adequate strength. DESCRIPTION OF SAMPLES Two types of cylindrical samples were used in this study 1) short, 1/2-to 1-in.-long samples to test the irradiation stability of the alloy and 2) 2-ft-long samples to investigate the resistance of an element to longitudinal deformation. Composite samples having 0.060-to 0.140-in. core diameters and clad with a 0.010-in. thick zirconium jacket were fabricated by coextrusion and by hydrostatic pressure bonding of the cladding to the preformed core material. Both fabrication processes produced the uniform metallurgical core-to-cladding bond which was felt necessary to minimize the uncertainty of the central core temperature. Both consumable-arc and induction-melting techniques were used to melt the uranium-sponge zirconium core alloy. Since a graphite crucible was used in induction-melting this alloy contained more carbon impurity, which resulted in a finer grain size than the arc-melted alloy. The core to cladding interface was uniform in elements coextruded from the fine-grain, induction-melted core material, while those elements fabricated using arc-melted core material had very irregular interfaces because of the coarser grain size. Both cold-worked and heat-treated fuel materials were irradiation tested. Cold-worked alloys were swaged to about a 5 pct final reduction in area without subsequent annealing. The heat-treated alloys were heated to 800°C, held at temperature for 15 min and furnace-cooled to about room temperature. This

Jan 1, 1960

By Harry H. Angst, Reuel A. Cochrane

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By E. R. Parker, D. L. Martin

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By S. J. Swainson

"It appears to me that the chief progress in milling operations in America have been made in the steady improvement of existing practice through both higher extractions and increased efficiencies of operations rather than by the development of new processes. The recent rapid development of sink-float, or heavy-medium separation, however, is an exception, and is becoming increasingly used to permit the economic treatment of certain low-grade ores that otherwise could not profitably be mined. The use of spirals and of small cyclones, both of which employ the principle of centrifugal force, show promise of increasing adoption through their application and efficiency in special cases." So did our distinguished colleague, O. A. E. Jackson, consulting metallurgist for the Union Corporation and president of the Chemical, Metallurgical and Mining Society of South Africa, summarize his impressions of a recent tour which he made of various metallurgical and milling plants in North America. I believe that all mineral dressers will agree with Dr. Jackson's concise conclusions.

Jan 1, 1950

By C. F. Wang

Page I. Introduction............:.............. 395 Manchuria in General ....................... 395 Pen-hsi-hu............................ 397 Pen-hsi-hu Coal & Iron Co., Ltd................... 399 I1. organization........................... 400 III. Coal Deposit........................... 402 Location..............................402 Geology............................. 403 Coal Mining...........'.................. 404 Mining Methods........................407 Mining Cost.........................408 IV. Coal Washing Plant.......................408 V. Coking Plant..........................410 VI. Iron Deposit...........................413 Magnetite Belt.......................... 413 Origin of Deposit......................... 414 Iron Mining........................... 415 VII. Concentration Plant........................ 417 VIII. Briquetting Plant.......................... 418 IX. Blast-furnace Smelting...................... 418 iNTKODtrCTION Manchuria in General Manchuria. called the "Three Eastern Provinces" in Chinese. forms the northeastern corner of China and is bordered by Siberia on the north and northeast. and by Korea on the east. It is a land famous in Chinese annals as the place of origin of the Ching dynasty. and in more recent times it has bcen an arena for diplomatic maneuvering and commercial competition between the Russians. advancing from the north. and the Japanese from the southeast. It derives its name of "three eastern provinces" from the fact that it is divided into three provinces; Hei-

Jan 1, 1918

By R. M. Brick

Segregation can occur only in cast alloys that solidify over a range of temperatures with a difference in composition of liquid and solid phases within this range (ignoring monotectic systems and chemical reactions as in rimming steels). Thus a pure binary eutectic alloy should show no segregation unless undercooling occurs for one of the solid constituents of the eutectic; e.g., chill-cast Al-I2 per cent Si alloys. The phasial condition implicitly described above—solidification over a range of temperatures with a compositional difference between solid and liquid—is found in nearly all solid solutions or combinations of solid solutions and eutec-tics, Metastable conditions of solidification of these types of alloys cause coring; i.e., a difference in composition between the center of a dendrite and its periphery. This composition gradient can be detected usually only by microscopic examination of etched structures; it is a "micro" effect. The gradient of more immediate industrial concern is that between the center of a cast section and the surface layers. This gross (macro) effect is usually deter-minable only by sampling of the casting at different points, with chemical analyses of each sample. If the compositional difference is of the same type as in coring, the first parts to freeze being enriched in higher-melting-point constituents, and vice versa, the effect is called normal segregation. When what is apparently the first part of the casting to solidify shows a higher concentration of low-melting-point constituents, the effect is called inverse segregation. These macro effects are quite separate from the micro effect, coring, yet the latter must be described first because it is an essential part of the picture. Coring Solid Solution, Ni-Cu The nickel-copper phase diagram is reproduced in Fig. Ia, in which the solid lines represent the equilibrium liquidus I, 3, 7 and solidus 2, 5, 8, and where the vertical I, 4: 8 represents a 55 per cent Cu alloy. Upon moderately rapid solidification, the first dendritic axes of composition 2 (see Fig. Ib) start to form at a temperature somewhat under I. Solidification continues by growth of the dendritic nuclei, but at temperature 4 the increment solidifying is of composition 5. The rapidity of this crystal growth prevents diffusion of nickel and copper atoms from adjusting the composition of the entire dendrite at 5, which it would be under equilibrium conditions. The average composition of a specific dendrite, or the entire solid phase, at temperature 4 might be that indicated

Jan 1, 1945

By D. L. Martin, E. R. Parker

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By C. R. Swarts

The use of compressed air or gas in oil wells for raising crude oil to the surface has, within the last year, become a dominant factor In production engineering. Previous application of this principle was largely confined to oil wells that had been pumping for a considerable length of time. In the Seminole area, the gas-air lift has been applied to wells imniediately after natural flow has ceased and in some cases while the wells were still flowing. This early application of the gas-air lift has been watchcd with intense interest by the petroleum industry, both with respect to methods of application and mechanical installations and to the effects on immediate and ultimate production. Methods of Application The Seminole pool at its inception contained sufficient gas associated with the oil to cause natural flow. As no frce gas was found in the main productive horizon, the Wilcox sand, all the gas present was dissolved in the oil, hence the natural flowing life was short, rarely lasting over 45 days. When natural flow ceased, high fluid levels were common, and as depth and crookedness of holes were obstacles to efficient pumping, the gas-air lift was used almost exclusively in raising the oil to the surface. Because of the high gravity of the oil, 41" A. P. I., and its high gasoline content, and also because of the desire to obtain production before offset wells became productive, quantity of production was the aim of the operators and a method of flow was used whereby this aim could be fulfilled. One of the outstanding features of this method consisted in flowing the wells through the annular space between the tubing and rasing. By this means a greater quantity of fluid could be handled than by flowing through the tubing of the size in ordinary use. Wells that would produce only a few hundred barrels on the pump were by this rnethod made to produce as high as 7000 bbl. on the lift. A few days or wreks of production at that rate meant a large recovery of oil. Casing of 636 in. diameter was commonly used as a production string with a 5 3/16-in. liner set on top of the oil sand. Upset tubing for irtro-

Jan 1, 1928

By W. O. Borcherdt

THE 650-ton underground mill of The Empire Zinc Company of Colorado (a subsidiary of The New Jersey Zinc Co.) serves the Eagle mine at Gilman in the Battle Mountain mining district of Colorado. The topography is rough, the mine and mill being under Battle Mountain and the alit entrance in the north wall of the canyon of the Eagle River, which is here a steel) gorge. The town of Gilman stands on a shoulder of the mountain at altitude 8975 ft., above sea level, along the Pike's Peak ocean to ocean highway and contains the company office and the usual facilities of a modern mining town. The railway contact is at Belden, altitude 8370 ft., at the bottom of the gorge directly below Gilman, where the westbound track of the Denver and Rio Grande Western Railroad is cut along the north bank and the eastbound track along the south bank of the river. A general description of the mine, mill and service facilities, with an account of the geology, character of the ore and methods of mining and milling having previously been published in a series of articles1, this paper will discuss with as little repetition as practicable the reasons for building the mill underground rather than as a conventional structure, the methods of construction employed and the experiences gained in what is apparently the pioneer plant of this type and extent.

Jan 1, 1937

By George Boulter

Draglines 8.2-1 Introduction. The nature and characteristics of rock and rock derivatives forming the crust of the earth vary so greatly from place to place that it is impossible to use the same numerical factors to show the, productive ability of excavating equipment on different jobs or projects. Factors for each project must be developed individually and applied as the conditions and requirements dictate. TYPES' OF DRAGLINES. Types of draglines are differentiated by the propelling method used and are generally divided into four classes, as follows: 1. Wagon mounted 3. Crawler mounted 2. Truck mounted 4. Walking Figure 8.2-1 shows a truck-mounted dragline. This type is considered to be the most mobile unit. In order to increase stability over the side, outriggers are installed as part of the truck chassis. This feature is not shown in .this figure. Figure 8.2-2 shows a crawler-mounted dragline. The long, wide crawlers are used to increase the stability and reduce the bearing pressure of this unit. These features allow for use of these units on surfaces too soft for the wagon- or truck-mounted types. Figure 8.2-3 shows a walking-type dragline. The large diameter tub and the well-supported boom through the gantry gives high stability for rugged works over a long life. BASIC PARTS OF A DRAGLINE. The basic parts of a dragline are illustrated in Fig. 8.2-4. A deck layout is shown in Fig. 8.2-5 with the main components named. OPERATION OF A DRAGLINE. Following is a description of the steps and controls present in a typical cycle of operation of a large dragline having independent hoist and drag motors. Starting the cycle with positioning the bucket on the ground under the point of the boom, the next step is

Jan 1, 1968

By Philip D. Anderson, Ralph Hultgren

Heat contents of extremely pure iron were measured over the range 300"to 1433"K, using a diphenyl ether calorimeter. Results from three samples containing widely differing impurities agreed with one another and with Previously reported results at higher temperatures (1184 ° to 1809°K) by Olette and Ferrier. From these data a table of heat contents of iron has been Prepared which is believed to be more accurate than those previously available. CP values have been derived which are consistent with these heat contents, with the best experimental Cp data, and with the thermodynamic conditions of equilibrium between bcc and fcc iron. The opinion is expressed that low-temperature extrapolations of presently known Cp values for y-Fe are not reliable. It would seem that the thermodynamic properties of iron, which is by far our most important metal, should have been well established long ago. This is not the case, however. As discussed by Olette and Ferrier,' there is objection to every earlier heat content measurement. While the best true Cp determinations agree well at temperatures below the Curie point, there is wide divergence at higher temperatures. Several investigators have examined available data and attempted to calculate thermodynamic functions for iron that are consistent with the two equilibrium temperatures of bcc and fcc iron. The two primary efforts were those of Austin' in 1930 and Darken and smith3 in 1948. The recommended values differ considerably; integration of Austin's Cp values leads to a heat content at 1100°K which is 300 cal per g-atom higher than the value recommended by Darken and Smith. The compilation of Fisher4 in 1949 was based on the selection of Austin. In 1956, Weiss and Tauer obtained yet another set of values by resolving Cp values into components due to dilation, lattice vibration, electronic excitation, and magnetism. The magnitude of contribution by each component and its dependence on temperature was estimated by semiempirical means. Their values are not self-consistent in that they do not form smooth curves when plotted vs temperature; moreover, their calculations cannot easily be repeated since they do not give the values of some of the parameters used. Clearly, experimental values for iron were in a most unsatisfactory state. The presently described measurements of the heat content of iron were therefore undertaken, covering temperatures as high as 1433°K. While the work was in progress, the high-temperature (1193" to 1789"K) heat content measurements of Olette and Ferrier' were published; in the region of temperature overlap the present results agree with Olette and Ferrier well within experimental accuracy. It is believed that the present results, combined with those of Olette and Ferrier, provide for the first time a reliable set of heat contents of iron from room temperature to the melting point. From these data, guided by available Cp measurements, it proved possible to derive Cp, entropy, and free energy function values for @-iron from room temperature to the melting point, and for y- iron in the temperature region of its stability. Exhaustive study led to the conclusion that extrapolations of y-iron functions to room temperature were not reliable enough to be useful; hence these have been omitted from the tables. EXPERIMENTAL Materials. Three samples of extremely high purity iron from different sources, containing widely different impurities, were measured. The first of these, designated "Chipman", was kindly supplied by Dr. K. K. Kelley of the U. S. Bureau of Mines from a lot which was made many years ago by Dr. John Chipman of the Massachusetts Institute of Technology. The second, designated6'Teddington", was supplied by the National Physical Laboratory, Teddington, England, from a lot zone-refined by them. The third sample, designated "Irsid", was supplied by the Institute de Recherches de la

Jan 1, 1962

By K. Huessener

In presenting the following data on combustion in the open hearth furnace and the advisability of automatic combusion control, the author finds himself much more severely handicapped by the lack of reliable test results than he had anticipated when he first undertook to write this paper. In order thoroughly to investigate how the results of an open-hearth furnace are influenced by combustion, one would have to draw up a large number of heat-balance sheets, as Kinney and McDermottl have given for one heat in their extremely able paper on "Open Hearth Efficiency,' presented before the American Iron and Steel Institute on October 27th,1 1922. Instead of covering only one heat, however, such heat-balance sheets would have to embrace a large number of heats, and not only for one kind of fuel, but for all the various fuels in customary use. Use of Radiation-protected Pyrometer Such tests necessitate extremely careful temperature readings, and here the first serious difficulty presents itself. Nearly all the temperature readings so far published have been taken with thermocouples for the lower ranges and with optical or radiation pyrometers for the higher ranges. This method of measuring reveals the temperature of the surrounding walls, or in the case of optical or radiation measurements, the temperature of that part of the opposing walls which has been focused by the instrument. The error in ascertaining the temperature of the gases entering or the waste gases leaving the checker chambers is probably not very large, as the flowing gases impart their temperature to the walls of the flues. On the other hand, the uptakes, where the preheat temperature of gas and air are usually measured, are under the influence of radiated heat from the port ends, and correct temperature readings can here be taken only by using a radiation-protected pyrometer of the aspirating type.

Jan 1, 1926

By J. H. Fletcher, S. M. Cassidy

Air has been cooled, heated, washed, humidified and dehumidified for many purposes and in many industries. At a number of metal mines air is conditioned to reduce the high humidity and unbearable heat found in deep workings, and at some mines air is washed to allay siliceous dust. Steam is introduced into the intake air at many coal mines, particularly in winter, for the purpose of keeping loose coal dust so moistened that the hazard of an explosion is lessened. This paper will describe a further successful application of air conditioning in a coal mine, where, for over three years, all intake air has been cooled to a constant temperature for the sole purpose of preventing roof falls. Effect of Warm Weather on Mine Roof It is generally known by mining men that some, if not all, coal mines have more trouble from bad roof during the warm summer months than in winter. Also, it has been observed that roof on intake airways is usually worse than on the return entries, after the air has circulated through the mine. Some mines and some coal seams are much more affected than others. In the Clinton district of Indiana, the No. IV coal seam has a good, firm, gray shale roof except during the summer months, when it deteriorates badly and falls in small slabs 1 to 6 in. thick. Timbering is not very efficacious during this period because in time the roof will shear around the supporting prop or crossbar and either dislodge the timber or leave it supporting only a few inches of crumbly shale (Fig. 1). This action is renewed each summer, choking airways with fallen slate, tearing down trolley wires, hampering haulage, endangering men and adding considerably to the deadwork cost. Only when mines have been worked for a period of years and have been advanced a long distance from the shaft do the active workings become comparatively free of this trouble, and even then the intake entries are still a source of much deadwork. Such was the annoying situation at the mine of the Saxton Coal Mining Co. operated in the No. IV coal just north of Terre Haute, Ind. During the months of warm weather it was possible to stand at any quiet spot in the mine and within 10 min. hear at least two or three falls,

Jan 1, 1931

INTRODUCTION Conditions for formation of porphyry copper deposits appear to have been propitious in the Appalachian orogen from the end of Precambrian into Middle Ordovician, and again from Middle Devonian into Mississippian. In the Appalachians we can now record the evolution of a porphyry copper province within a developing orogen, one that reached metamorphic and structural maturity by the end of Devonian. Fig. 15, after Irwin and Coleman (1972), locates that portion of the Appalachian orogen included in this study, and Fig. 16 illustrates general geology of the area. Deposits mentioned in Table 3 and in the text are shown in Fig. 16. Data presented summarize personal observations by the author, published descriptions of specific areas noted in the bibliography, and abstracts from Provincial assessment files. Sources of previously published data are acknowledged. Few comprehensive descriptions of individual porphyry copper deposits in this area exist, so much of the data presented is new to the literature. Porphyry mineralization has, for this chapter, been restricted to porphyry copper de- posits, although porphyry molybdenum de- posits (Clark, 1972) are also shown in Fig. 16 (Hollister, et al., 1974). Copper- molybdenum and tungsten-molybdenum skarns are also omitted to simplify discu sion, though each is known in the area studied. Gaspe Copper is included, however; min- eralization in this deposit is present in the intrusion as well as in the skarn adjacent (Bell and Scott, 1954). Porphyry deposits listed in Table 3 are included because of some important feature, although other deposits have been reported (e.g., Kirkham and Soregaroli, 1975 ) . Clearly, no table now compiled could be complete. The pace of exploration insures that new occurrences will probably be found. Summaries of features exhibited by intrusions shown in Table 3 should remain valid, however, since they appear representative and are based on an adequate number of deposits in the area studied. Paleozoic porphyry copper prospects (shown in Fig. 16) are more common, apparently, in the northeastern part of the orogen, rarely having been found south of Catheart or west of the Logan Line. Occurrences of molybdenum and other associated lithophile elements are, however, known to the south and west as well as further north. Killeen and Newman (1965), King (1970),

Jan 1, 1978

By C. D. Demond

In reverberatory smelting, fuel is the chief item of expense, as it commonly is in processes using large percentages of it. Hence the most suitable supply is eagerly sought; that is, the supply which, in the end, yields the greatest net profit. The better grades are not infrequently bought, even at an advanced price, because they are apt to be decidedly more economical. High price, of itself, however, is no merit, for freight is generally the largest part of the cost of fuel, and the nearby supply may yield as high efficiency as that from a greater distance. If a poorer grade is reasonably good, and if its cost is low enough to more than offset the decreased technical efficiency, it is of course the more suitable. Any smelting operation depends for both efficiency and economy on raising the furnace atmosphere considerably above the "critical" temperature; that is, above the temperature at which smelting is completed. If this temperature is not exceeded, smelting stops, no matter how much coal is burned; and the real value of a fuel depends on the number of degrees that the temperature is continuously kept above this point. For example, if one fuel maintains 2,500" F. and another only 2,100 F., while the "critical" temperature is 2,000" F., the first is worth at least five times as much as the second, although the increase above atmospheric temperature is only one-fifth more in one case than in the other. This "margin of temperature" above the smelting point is much more significant than the total number of heat units developed from the fuel. The case is parallel to that of water flowing from a pipe. The reservoir may contain a billion gallons of water; but, even though the fluid has come to the nozzle, not a drop will run out, where it can be of practical use, unless the level in the reservoir is higher than the nozzle; and the speed and volume of flow depend on how much higher the level is in the reservoir than at this point. If the temperature in a furnace is not above the critical level there will be no slag to flow over the skimming plate, even though there are enough heat units to bring an unlimited quantity of charge up to the point of slag formation; and just as the value of a water supply for the purpose of putting out a fire depends largely on the effective head, so the difficulties of furnace management

Jan 1, 1915

By R. B. Snow

This paper describes a technique of polishing and etching specimens of open-hearth furnace slags or hearth aggregates for identification of the crystalline constituents —lime (CaO), tricalcium silicate (3CaO.SiO2), dicalcium silicate (2CaO.-SiO2), rnonticellite (CaO.MgO.SiO2), or forsterile (2MgO.SiO2), with especial em-phasis on the mineral merwinite (3CaO.-MgO.2SiO2). With proper standardization, this identification does not require the use of the petrographic microscope. The composition of basic open-hearth slags and furnace bottoms falls, almost without exception, within systems containing CaO, MgO, 'IFeO,,, MnO and SiOz, in which the number of basic molecules so greatly exceeds the orthosilicate ratio (two molecules of base to one of silica) that free basic oxides, and combinations between them such as alumi-nates or ferrites, are present in cooled specimens. Orthosilicates of (CaO + NgO) are the most common in such specimens, since in nearly all cases, except premelt slags, the molecular ratio of (CaO + MgO) to SiO, is more than 2 to I. When sufficient lime is available it combines with the silica to form dicalcium silicate (2Ca0.Si02), which contains little, if any, IvfgO, FeO or MnO in solid solution whereas the latter oxides combine to form the oxide solid solution known as periclase. If the lime present is insufficient to form dicalcium silicate (2Ca0.Si02) it combines with Mgo to form either merwillite or moIlticellite (SiOz); these minerals take little if any FeO or MnO into solid solution and the remaining MgO, FeO and hInO combine as periclase. This generalization seems to be valid for basic slags and furnace bottoms, since minerals such as Ca0.MnOSi02 and CaO.FeO.SiOz are found only in slags in which the lime-silica ratio is less than 2 and are not observed in 'pecimens from furnace bottoms. The identification of crystalline constituents in such materials, especially of fine crystals in the groundmass, is difficult under the petrographic microscope. They are often masked by their neighbors because of their small size in relation to the thickness of the thin section and because of the presence of Opaque Or colored constituents. The indices of refraction and the optical sign of the mineral are sometimes difficult to determine because of the small size or because Of twinning or of inclusions within the crystal. Moreover, the positive identification of merwinite (3Ca0.Mg0.2Si02) from its optical properties is usually difficult in the presence of dicalcium silicate (zCaO.SiO2). CaO, MgO, jCa0.Si02 and 2Ca0.SiOz in open-hearth 'lags have been identified for a number of years in the U.S. Steel Corporation Laboratory by the usual

Jan 1, 1948

By R. B. Snow

This paper describes a technique of polishing and etching specimens of open-hearth furnace slags or hearth aggregates for identification of the crystalline constituents —lime (CaO), tricalcium silicate (3CaO.SiO2), dicalcium silicate (2CaO.-SiO2), rnonticellite (CaO.MgO.SiO2), or forsterile (2MgO.SiO2), with especial em-phasis on the mineral merwinite (3CaO.-MgO.2SiO2). With proper standardization, this identification does not require the use of the petrographic microscope. The composition of basic open-hearth slags and furnace bottoms falls, almost without exception, within systems containing CaO, MgO, 'IFeO,,, MnO and SiOz, in which the number of basic molecules so greatly exceeds the orthosilicate ratio (two molecules of base to one of silica) that free basic oxides, and combinations between them such as alumi-nates or ferrites, are present in cooled specimens. Orthosilicates of (CaO + NgO) are the most common in such specimens, since in nearly all cases, except premelt slags, the molecular ratio of (CaO + MgO) to SiO, is more than 2 to I. When sufficient lime is available it combines with the silica to form dicalcium silicate (2Ca0.Si02), which contains little, if any, IvfgO, FeO or MnO in solid solution whereas the latter oxides combine to form the oxide solid solution known as periclase. If the lime present is insufficient to form dicalcium silicate (2Ca0.Si02) it combines with Mgo to form either merwillite or moIlticellite (SiOz); these minerals take little if any FeO or MnO into solid solution and the remaining MgO, FeO and hInO combine as periclase. This generalization seems to be valid for basic slags and furnace bottoms, since minerals such as Ca0.MnOSi02 and CaO.FeO.SiOz are found only in slags in which the lime-silica ratio is less than 2 and are not observed in 'pecimens from furnace bottoms. The identification of crystalline constituents in such materials, especially of fine crystals in the groundmass, is difficult under the petrographic microscope. They are often masked by their neighbors because of their small size in relation to the thickness of the thin section and because of the presence of Opaque Or colored constituents. The indices of refraction and the optical sign of the mineral are sometimes difficult to determine because of the small size or because Of twinning or of inclusions within the crystal. Moreover, the positive identification of merwinite (3Ca0.Mg0.2Si02) from its optical properties is usually difficult in the presence of dicalcium silicate (zCaO.SiO2). CaO, MgO, jCa0.Si02 and 2Ca0.SiOz in open-hearth 'lags have been identified for a number of years in the U.S. Steel Corporation Laboratory by the usual

Jan 1, 1948

By Henry S. Rawdon

The structure of wrought iron as usually described by metallographists and workers in metal in general is that of a fairly pure iron. Impurities, if present, are usually considered as being in solid solution in the crystals of the ferrite matrix or as forming part of the ever present "slag streaks." Attention is herein directed to one type of these dissolved impurities; to the detection of such impurities, particularly in low-grade irons, and to their possible influence on the physical properties of the metal. The attention of the Bureau of Standards was first directed to wrought iron of the peculiar and unusual characteristics to be described later, in material which had failed in service and was submitted for test. The examination was extended to other grades of wrought iron, to see whether such features are of common occurrence in this class of material. MICROSTRUCTURE OF WROUGHT IRON Usual Structure The general microstructure of wrought iron is so well known that a detailed description of it here is needless. There is shown in Fig. 2 the structure of a sample of Swedish iron which illustrates well the matrix of ferrite crystals in which are embedded the slag threads so characteristic of the puddling process and the subsequent working of the material. The usual commercial product contains varying amounts of the impurities commonly associated with iron and steel, i,e,, manganese, phosphorus, silicon, and sulphur together with small amounts of carbon. Of these, the larger part of the phosphorus and some of the silicon present are held in solid solution in the ferrite while most of the remaining impurities, other than carbon, exist in the in closures of slag. Aside from the discontinuities introduced by the slag streaks the ferrite matrix has the microstructure and appearance of a pure metal. No definite orientation of the various crystals or grains is apparent; deep etching of the specimens reveals no intracrystalline features (i.e., within the grains) other than those noted in " pure " metals in general (etching pits).

Jan 1, 1918