Search Documents

By C. D. Hall

This paper may be divided into two main parts: (1) analysis and data to show that Eq. 6 adequately correlates the authors' experimental data, and (2) the assertion that Eq. 20 "should permit scale-up with data taken from one pipe diameter for Newtonian, inelastic non-Newtonian, and viscoelastic fluids, such as dilute polymer fracturing fluids, which produce considerable pressure reductions." The authors might well recommend that this broad grouping of fluid types could be correlated by using Eq. 6 (requiring data from at least two pipe diameters). On the other hand, Eq. 20 is only shown to be adequate for conditions within the range of the present data set. Specifically, predictions by Eq. 20 for diameter scale-up to casing sizes would give larger deviations than implied in Table 2, and scale-up for some other fluids that give large drag reduction could be grossly in error. The description of a class of fluids "which produce a diameter family of straight parallel lines on a log (d?p/4L) vs log (8 v/d) plot. . ." defines a necessary condition for using Eq. 6; i.e., that s shall be constant for each fluid. The proposal that Eq. 20 is applicable to turbulent flow of such fluids is equivalent to saying that the spacing of these parallel lines, with A being constant, will be found to correspond to m = -1.20 for all such fluids. Table 1 shows the values of m derived from data on 16 non-Newtonian fluids. The key statement of this paper is that the diameter exponents "do not vary significantly from . . . -1.20." In statistical terms, this says that the m value for each fluid, which was obtained from all the measurements made on that fluid. has not been shown to be different from the arithmetic mean of the m values for the 16 fluids tested. This implies that the group mean, -1.20, is a more reliable value to use for an individual fluid than is the m value derived from the data on that fluid alone. No statistical test is described to support the key statement that the diameter exponents do not vary significantly from -1.20. Such a test would have to take into account that each individual m value is shown to correlate the pressure gradients for its fluid, with only about 3 percent standard deviation over the diameter range covered. That is, the m value is not the result of a single independent measurement. Thus, it would not be sufficient, or valid, to compare the deviation of one of the m values with the variance of the 16 values of m about their mean. An alternative interpretation of the key statement is that the diameter exponents do not vary appreciably from -1.20; i.e., that using -1.20 does not cause serious inaccuracy. Table 2 seems to be offered in support of such an assertion. However, such a statistical treatment (1) is unnecessary and (2) cannot lead to any valid scale-up generalization. The amount of error introduced by using a 1"wrong" value of diameter exponent — i.e., -1.20 instead of m — is determined by Eq. 6. The ratio of the pressures predicted by Eqs. 6 and 20 for scale-up from ds in small pipe to d, in casing is The pressure for 30-percent calcium carbonate slurry (m = -1.112) in 10-in. ID pipe would be predicted 30 percent higher by Eq. 6 than by Eq. 20, if based on tests in 0.5-in. ID pipe. The data set tested in Table 2 represents only a limited sample of pipe diameters (ratio of about 4:l) out of the population of diameters that would

Jan 1, 1970

By V. Koump, R. H. Tien, W. J. Kim

This paper presents an approximate solution of the problem of freezing of a binary alloy. he alloy is in the form of a one-dimensional slab of finite thickness. The surface temperature of the slab is assumed to be constant and lower than the solidus (or eutectic) temperature. The densities of the liquid and the solid are assumed to be equal. For a given binary alloy system, initial concentration of solute and surface temperature, the solution yields a) the temperature distribution in the solid skin, b) the temperature, concentration, and solid fraction distribution within the solid-liquid region, and c) the positions of the liquidus and the solidus (or eutectic) fronts as a function of time. The results of calculation for Fe-C and Fe-P systems are presented. In this investigation we are considering the problem of solidification of a binary alloy. The alloy is in the form of a one-dimensional slab of finite thickness. The molten alloy is initially at liquidus temperature. At time zero the surface of the slab is reduced to a temperature T, < Te,, where Te, is the solidus (or eutectic) temperature and T, is a constant. The densities of solid and liquid alloys are assumed to be equal and independent of temperature and composition. A qualitative picture of solidification of an alloy, under these conditions, is illustrated in Fig. 1. During the initial stage of solidification, before liquidus front reaches the center of the slab, freezing proceeds by propagation of two isothermal fronts, the liquidus front and the solidus (or eutectic) front. The fraction of solid at the liquidus front is zero; the fraction of solid at the solidus front is unity, The solid fraction and the temperature distribution between the two fronts and the width of the solid-liquid region change with time. During the later stage of freezing, after the liquidus front reaches the center of the slab, the liquidus front disappears. The solid fraction and the temperature at the center of the slab, as well as throughout the solid-liquid region, are now changing with time. The solidification is completed when the fraction of solid at the center of the slab reaches unity. In solution of this problem we seek to determine a) the temperature distribution in the solid, b) temperature, concentration,

Jan 1, 1968

By W. D. Kruger

Methods for analyzing flooding or cycling projects by means of two-dimensional flow calculations are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The accuracy of such analyses depends on the basic reservoir data employed, especially the absolute permeability distribution in the reservoir; however, absolute permeability data normally are determined from well flow tests and/or core measurements and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. A calculation procedure is presented for determining the areal permeability distribution in the reservoir. Use of the procedure allows verification of the basic reservoir data through the matching of past reservoir conditions, thereby providing proper data for reliable predictions of future operations. The calculation procedure is a numerical technique based on a mathematical model of the reservoir and is designed for solution by means of an electronic digital computer. Results from field application of this procedure are presented. Permeability distributions from measured data are compared to those calculated to indicate the need for the analysis. Comparisons of field-measured and calculated pressure distributions are given to establish the validity of the calculation procedure. The conclusions of this paper are (I) use of the calculation provides data that allow a match of past reservoir conditions and thus reliable prediction of future operations; and (2) the procedure should, where applicable, be used to provide adequate reservoir data for use in two-dimensional flow calculations and related reservoir analyses. INTRODUCTION One means of providing more precise engineering control over reservoir operations during all stages of depletion is to develop some type of model to simulate the reservoir, using information developed from the behavior of the prototype to predict the performance of the actual reservoir. The use of mathematical rather than physical models for this purpose has been gaining in importance recently because of the application and availability of electronic computers. Mathematical models avoid instrumentation difficulties and allow easier handling of large-scale problems. At present, analyses employing two-dimensional models are common, and thought is being given to the use of models in three dimensions. The use of multi-dimensional models is necessary to show not only what is occurring in the reservoir, but also where in the reservoir the phenomena of interest are taking place. Methods for analyzing flooding or cycling projects by means of two-dimensional numerical models are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The applicability of numerical models and the results of using such analyses have been presented through field examples. The references indicated here discuss fully the data necessary to build the mathematical reservoir model and the way the model is used to study or predict the future performance of the reservoir. The accuracy of the analysis of such projects depends on the basic reservoir data employed in the construction of. the model. In order to be sure the model represents the reservoir, it must be used to match some known set of reservoir conditions, i.e., to match past reservoir performance. The accuracy of the model is directly dependent upon the absolute permeability distribution in the reservoir; however, absolute permeability data are normally determined from well flow tests and/or core measurements, and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. There is always the need for better data and for verification of existing data. The purpose of this paper is to show the use of the mathematical model to match past performance in flooding or cycling projects, the use of numerical techniques to adjust the basic absolute permeability data if necessary so that a match is obtained, and in this way to generate the effective areal permeability distribution of the reservoir. A review of the basic concepts of the numerical model will be given, followed by a discussion of the data-adjusting technique for matching past performance. TWO field examples will be cited to show

By P. G. Winchell, J. K. Jackson

The strtcture of body-centered Fe-Ni-C alloys (0 to 16.5 wt pct Ni) containing less than 0.015 wt pct C was investigated by measuring the carbon-diffusion peak at low frequencies with a torsion pendulurrr. By determining the Snoek damping in ferrite and in quenched alloys of identical composition, the effects of nickel content and heat treatment were separated, and the existence of a structure in which Snoek damping is greatly reduced was revealed in the quenched ternary alloys. The relative amount of this structure increases with increased nickel content and cooling rate. It is proposed that this structure may be highly imperfect or tetragonal. In Fe-Ni-C alloys containing only ferrite the addition of nickel (0 to 5.1 wt pet) decreases tke area of the carbon-diffusion peak and shifts its position to lower temperatures but broadens the peak only slightljl. The decrease in peak area with increasing nickel implies that short-range interactions with the nickel atoms prevent some of the carbon atoms from participating in the relaxation process. The shift in the peak position indicates a long-range effect of nickel on the movement of carbon atoms so that at 300°K the diffisivity of carbon in -ferrite is increased by about 35 pct by the addition of 5.1 tut pct Ni. The results are presented as distributions of relaxation strength 072 the activation energy under the assumption that the frequency factor is invariant. BODY-CENTERED iron-base solid solutions dissolve carbon interstitially in the octahedral sites. The occupation of an octahedral site produces a tetragonal distortion of the surrounding lattice. These sites fall into three sets according to the orientation of the tegragonal distortion associated with each and may be identified by their lattice coordinates as: type 1/2 0 0, type 0 1/2 0, type 0 0 1/2. At low carbon levels in cubic ferrite the carbon atoms are distributed at random1 among these sites. In high-carbon body-centered iron-base solid solutions, which are unstable with respect to several two-phase mixtures, a tetragonal structure occurs as the product of the diffusionless transformation of austenite. This transformation is commonly accompanied by appreciable microstrain and its product is called martensite. The tetragonality of martensite, a supersaturated solution of carbon in a iron, is maintained prior to decomposition even though local diffusion of carbon occurs as evidenced by carbide precipitation. The tetragonality is taken as evidence that one set of octahedral sites is preferentially occupied by carbon. (This preferential occupation is called ordering below.) Support for this view is presented by the absence of strain-induced carbon-atom diffusion in high-carbon solid solutions (martensite). Such diffusion occurs in ferrite and produces the 40°C internal-friction peak observed at 1 cps frequencies.&apos; Thus, there appears to be qualitative evidence favoring the view that at sufficiently high carbon levels tetragonality arises spontaneously as a result of the ordering of the carbon atoms; however, no experimental evidence exists concerning an equilibrium between cubic and tetragonal body-centered solid solutions. Moreover, attempts to estimate the energy of ordering7-&apos; predict a value too low to maintain the tetragonality observed at medium carbon levels, 0.3 to 0.6 wt pct C. In the present work an attempt using internal-friction measurements is made to establish the presence or absence of tetragonality in low-carbon body-centered solid solutions formed by quenching austenite. Fe-Ni alloys containing about 0.01 wt pct and 0 to 15 wt pct Ni were selected for the study. While the work was in progress Gilbert and Owen10 reported that the transformation which occurs in these alloys during quenching at rates up to 5000°C per sec is not martensitic but is more properly categorized as massive. Thus, the solid solution

Jan 1, 1964

By W. C. Knopf, I. M. LeBaron

In the Carlsbad area potash is dry-mined and wet-concentrated. Wet concentration involves recircu-lation of saturated brines, with resultant difficulties of brine disposal and inherent losses in recovery through solution of the KCl. A dry beneficiation process for potash minerals would offer many advantages over present methods. International Minerals & Chemical Corp. has been working on development of a dry process for some time. This article is a progress report. Potash ores available in this country are largely mixtures of halite and sylvite contaminated with slimes and often with many sulfate and magnesium minerals. Electrostatic concentration of KCl when the contaminating minerals are in low percentage has been accomplished. Continuous production of better than 60 pct K2O concentrate from high potassium sulfate ores has not been demonstrated at the present time. Laboratory Procedure: Laboratory work on electrostatic beneficiation of potash minerals has been carried out using both pure crystals and mined ore. Electrostatic separation of the two main components of potash ore, sylvite (KCl) and halite (NaCl), is accomplished by first heat-treating the ore to allow for electric charging of the particles. Preferential exchange of&apos; electrical charges between different mineral particles through surface contact is the principal mechanism involved. After proper conditioning of the particle surfaces, the oppositely charged minerals are dropped vertically into a horizontal electric field having a field gradient from about 5000 to 15,000 v per in. The particles are free-falling in the field. A suitable power supply is used to produce the proper total voltage for the electric field. Total required voltage is, of course, a function of electrode spacing. A typical electrode arrangement with power supply is shown in Fig. 1. In general, the total voltage on any system is 75,000 to 90,000 v. Power consumption is negligible, as leakage at insulators and corona discharge are the main losses in the system. Optimum preheat temperatures for pure material components generally are not the same as for mined minerals. Fig. 2 shows clearly that maximum recovery on a 50 pct pure KCl, 50 pct pure NaCl mixture occurs at a preheat temperature of about 600°F. In this test the preheat mixture was allowed to cool to about 225°F before dropping through the electric field. The optimum temperature for sep- aration is practically never the optimum temperature of preheat. Optimum separation for mined Carlsbad potash ores occurs when a preheat temperature closer to 900°F is used, as shown by Fig. 3, which plots percent sylvite (KCl) in the concentrate and tails as a function of preheat temperatures. Here again the ore was allowed to cool to about 225°F before separation. It should be noted that efficiency of separation increases continuously with increasing preheat temperatures until incipient fusion of the ore takes place at about 950°F. The increase in optimum preheat temperature for Carlsbad ores over the pure minerals can be traced to the effect of the clay slimes intimately associated with the mined potash. If the slimes associated with the ore are removed by washing with alcohol or other non-aqueous material, the necessity of preheating to the high temperature is removed. This temperature range has been proved critical within these limits during continuous pilot plant operation. Concentrate and tailings grade and optimum recovery also are functions of the temperature of the potash mineral particles during separation in the electric field. Fig. 4 presents data indicating that feed to the rougher pass should range between 150°F and 275°F for best results. It has been found by subsequent pilot plant work that these temperatures can be maintained in actual operation.

Jan 1, 1959

By AIME AIME

ON Sept. 24, 1875, a remarkable deposit of silver ore was discovered by James Ryan and Samuel Hawkes at the east base of Grampian Hill in central Beaver County, Utah.. A shaft was begun and had been sunk about 30 ft. in ore when the claim was sold on Feb. 17, 1876, to A. G. Campbell, Matthew Cullen, Dennis Ryan, and A. Byram for $25,000. To them is due the credit of having developed the mine and started the district on the road to its present state of prosperity. Their development resulted in proving the vein to a depth of over 280 ft. and about 2500 tons of ore was extracted and turned into bullion. In February, 1879, the mine came into the possession of the Horn Silver Mining Co., and since then over $65,000,000 worth of ore has been taken from the mine. Two smelters were built in 1878, near the mine; 400 men were employed underground, and 1000 on the surface, burning charcoal, hauling wood from the surrounding hills, and freighting and hauling hay for the hundreds of horses used in the work. Ore was hauled thirty miles to the

Jan 1, 1936

By M. R. Geer, H. F. Yancey, P. S. Jacobsen

Two growing problems confront the preparation engineer—still further restrictions on stream pollution and a greater proportion of fine coal as more and more continuous miners come into use. The de-watering screens, centrifuges, and settling ponds that sufficed a few years ago must often be supplemented by more effective equipment, and in some instances the finest solids are now being recovered by vacuum filtration, once considered too costly in many coal washeries. Unfortunately not all slurries can be readily filtered. Some are virtually unfilter-able, and others do not permit the high cake rates needed to hold costs within reason. Often, however, these difficult slurries can be rendered filterable by flocculation. Starch and lime have long increased settling rate in thickeners and can also aid filtration. More recently there have been other flocculants, primarily synthetic polymers or gums. Reports of their great effectiveness prompted the U. S. Bureau of Mines to test their use in filtration as part of its program on recovering and cleaning fine coal. The object of the present work was to compare some of the newer flocculants with starch and lime and to test the reaction of different types of slurries to flocculation. Three natural slurries, three synthetic coal-clay mixtures, and five flocculants were tested, all with a laboratory filter leaf. Slurries and Flocculants Tested: First of the slurries was the thickener feed from the washed coal section of the Michel colliery of Crow&apos;s Nest Pass Co. Ltd., Michel, B.C. As shown by the screen and ash analyses in Table I, practically all this slurry was finer than 28 mesh, and about half the solids were finer than 200. Substantially all material coarser than 200 mesh was clean coal, but the ash content of 20.7 pct in the finest size indicates a moderate amount of impurity. This coal is medium-volatile bituminous in rank. Slurry was also obtained from the Black Diamond washery of Palmer Coking Coal Co., King County, Wash. This underflow of a 1/2-mm vibrating slurry screen is a waste product discharged to a settling pond. As shown by the data in Table I it contained about 20 pct material finer than 200 mesh, which analyzed 77.5 pct ash, indicating a high proportion of clay. The coarser sizes were also high in ash content because of the presence of bone and shale. Black Diamond coal is on the dividing line between bituminous and subbituminous rank. The third slurry, from the washery of Roslyn-Cascade Coal Co. in Kittitas County, Wash., was the underflow of a battery of 8-in. cyclones that is wasted with the coarser refuse from the plant. In both size and ash content this slurry was similar to the Black Diamond, but since it was a cyclone-underflow product, the fraction finer than 200 mesh undoubtedly contained a much smaller proportion of finely divided clay than was present in the Black Diamond slurry. The Roslyn-Cascade coal is high-volatile A bituminous in rank. Initially the slurry samples were stored in the laboratory at a concentration of 40 pct solids. A progressive change in filtration and flocculation characteristics during storage was noted, however, presumably because of progressive disintegration of the clay. After careful testing demonstrated that the slurry solids could be dried and then repulped without changing the original filtration characteristics, this procedure was adopted. The flocculants used were Separan 2610, Kylo 27, Jaguar MD-A, Idaho potato starch, and lime. The lime was used as a slurry, the Separan 2610 as a 0.10 pct aqueous solution, and the other flocculants as 0.50 pct aqueous solutions. The starch was causti-cized with sodium hydroxide before use. As some of the flocculants are reported to deteriorate on storage, new batches of flocculants were prepared every two days. Test Procedure: Fig. 1 diagrams the filter leaf apparatus employed. This consists of a test leaf having an effective area of 0.10 sq ft., a 60°, 8 1/2-in. diam cone to hold the slurry sample, a variable-speed electric stirrer, vacuum gage, bleed line for controlling vacuum, filtrate flask, moisture trap, and vacuum pump. Two filter cloths were selected—Saran SA 603, a monofilament, coarse-weave cloth, and polyethylene PO-801 HF, a monofilament, fine-weave cloth. The Saran was selected to provide maximum cake rate without regard to clarity of filtrate and the polyethylene to provide the best quality of filtrate without regard to cake rate. The test charge for the filtering vessel consisted of 800 g of solids (previously soaked for 24 hr) and

Jan 1, 1960

By K. Mukherjee

A quasi-thermodynamic calculation is presented for estirt~ating vacancy Parameters in fcc metals. For fcc metals the equilibrium vacancy concentration at the melting point can be approximated by a constant mole fraction. The Gibbs free energy of formation of the vacancies can then be expressed as a simple function of the absolute melting temperature alone. From this description the formation energy Ef, the vibrational entropy Sv, and the formation volume of a vacancy can be calculated in terms of known thermodynamic parameters. The calculated values are in good agree-rnent with available experimental results. IT appears that many of the physical parameters associated with lattice defects can be empirically related to thermodynamic melting parameters.&apos;-7 Besides the implicit correlations between melting phenomenon and point defects, the melting temperature itself at atmospheric pressure can be used as a reference temperature for the purpose of comparison of vacancy concentrations in a given crystal class. The concentration at the melting point then corresponds to the maximum vacancy super saturation in the crystalline state at a fixed pressure. For pure fcc metals such as Au, Cu, Al, Ag, Pb, and Pt the mole fraction of vacancies at the melting point8 is of the order of 10*"3 to 10"1. The equation expressing the equilibrium vacancy concentration at the melting point contains three parameters: the formation energy, the vibrational entropy, and the absolute melting temperature, see Eq. [2]. Since these three parameters cover a wide range of values8 in the above-mentioned metals, it can be assumed that in other fcc metals, for which no reliable data are available, the mole fraction of vacancies at the melting point most likely lies in the range 10~3 to lO"4. This is then the basis of the calculations described in this article. Within this range the mixing entropy can be linearized and the vibrational entropy, the formation energy, and the vacancy formation volume can be calculated in terms of known thermodynamic constants. 1} LINEARIZATION OF MIXING ENTROPY The Helmholtz free energy of a crystal containing n vacancies at the melting point can be writteng as where Ef, T,, k, and S, are the formation energy of a vacancy, the absolute melting temperature, Boltz-mann&apos;s constant, and the vacancy formation entropy, respectively. After applying Stirling&apos;s approximation in Eq. [l] and minimizing with respect to n where (n/N), is the equilibrium vacancy concentration in mole fraction at the melting temperature at 1 atm pressure. If instead of setting (6~/6n) = 0 immediately after Stirling&apos;s approximation in Eq. [I], the configurational partition function is simplified, then some useful and significant results can be obtained by utilizing the experimental inforrnation After applying Stirling&apos;s approximation and rearranging is plotted as a function of (n/N) in Fig. 1. The points, not all of which are shown, are fitted by a straight line substituting from Eq. [5] into Eq. [I] and minimizing with respect to n combining Eqs. [6] and [2] It must be emphasized that Eq. [7] is only a crude approximation based on an oversimplified model of

Jan 1, 1967

By D. K. Deardorff, Earl T. Hayes

An improved technique is described for the accurate determination of melting points of metals in the temperature range 1500&apos; to 2500°C. The improvements consist of gradient heating and refinements in cavity preparation to obtain true black-body conditions. The melting point of hafnium, as determined by this method, is set at 2222°±30°C. This is over 200°C higher than one of the values reported earlier. Discrepancies in the previously reported values for the melting point of hafnium are explained. The melting points of zirconium and titanium are found to be 1855O±15OC and 1668°±10°C, respectively. Reproducibility of results was ±3OC. PRIMARILY, this report is being made to correct a 1975o±25oC1 value for the melting point of hafnium, and to present an improved method for melting point determination. As a matter of interest, the technique was also applied to determining the melting point of zirconium and titanium. There is a wide difference in the melting point of hafnium as reported by competent investigators. DeBoer and Fast&apos; reported a value of 2230°±500C, and later work of McPherson, as reported by Aden-stedt, placed the melting point at 1975o±25oC. Zwikker" calculated that the melting point was 2430°C. In resolving this discrepancy, improvements were made in the procedure for determining the melting points of refractory metals in the range 1500" to 2500°C. Special techniques are necessary to determine the melting point of these metals accurately. Since the metals oxidize in air above 900oC, the determinations must be carried out in an inert gas or vacuum. Also, every known refractory contaminates them to some extent. In addition, the attainment of true black-body conditions is always difficult. DeBoer and Fast actually determined the melting point of Hf-Zr as-deposited iodide process alloys and extrapolated to 100 pet Hf. McPherson employed a tungsten wire suspension similar to that described by Schramm, Gordon, and Kaufmann,1 and used hafnium metal produced by the iodide process. There was no apparent reason for the wide spread in melting points, since the quality of the metal was very good and the work was under the direction of highly competent investigators. Retracing some of this work revealed one understandable error in the case of hafnium, and led to development of an improved technique for determining melting points of reactive metals in the range 1500" to 2500°C. Material Crystal bar hafnium, zirconium, and titanium were used for this work, with analyses as shown in Table I. The hafnium was of the highest purity that has been prepared, though not as pure as the zirconium and titanium. At the instigation of the Pittsburgh Area Office of the AEC, a special lot of Hfo2 was purified, converted to the tetraflouride, and bomb-reduced with calcium, all at the Iowa State College Laboratories. This crude hafnium metal was then refined by the iodide process at the Foote Mineral Co. All specimens were cut with a Sic wheel, ground, pickled, and dried carefully before use. Procedure General Tungsten Suspension Method—In this method, a small specimen is suspended by a fine tungsten wire in a slender, induction-heated tungsten or tantalum cylinder, all under vacuum. The melting point is determined by heating the specimen slowly while observing it with an optical pyrometer focused upon a portion of the specimen that radiates as a black body. This means that there should be no reflected radiation, either from colder objects near the pyrometer or from hotter surfaces. The induction heater would be the only hotter object and, if it is slender enough, the specimen will attain the same temperature. Often a slender hole is drilled into the specimen as a source of black-body radiation. This was the general method used by McPherson in obtaining his value of 1975°C for the melting point of hafnium. In trying to repeat this work, it was found that the points of contact between the

Jan 1, 1957

By H. R. MacMichael

IN the Chihuahua district of Mexico the first smelting was that inaugurated by the early Spaniards for the production of silver bullion. The ores treated were high in silver and lead. Silver-lead bullion was first produced and the lead then cupelled to waste, with the slag produced running from 5 to 10 per cent in lead and about 25 to 40 per cent silica. The ore was mined by peon labor, often being carried out of the mine on the backs of the men, and then transported by burros. Furnaces were of primitive construction, adobe or rock being used in the earlier period and some iron later when it became available. Blast was originally supplied by bellows manually operated. Such smelting was carried on to a greater or lesser extent until the latter part of the last century, and so extensive was it that many hundred thousand tons of leady slag remained to be treated in modern furnaces. In 1908 a smelter was placed in operation at Chihuahua by the American Smelting & Refining Co. At that time the ore was practically all oxidized and by a little selection, self-fluxing mixtures could be made, but with an average lead content usually under 10 per cent and sometimes as low as 7 per cent. The bullion produced would carry from 150 to 300 oz. silver per ton. The slag made approximated 30 per cent SiO2, 42 per cent FeO, 21 per cent CaO, and perhaps 3 per cent Zn. The ores varied from hard, coarse material which was passed through a crusher, to a considerable quantity of fines which had to be smelted as it came, as crushing the coarse was the only preparation for smelting.

Jan 1, 1933

Allan Gibb, Mount Perry, Queensland, Australia (communication to the Secretary):—In drawing conclusions from his observations, Mr. Van Liew has apparently overlooked the reduction in weight that takes place in the content of the converter. The percentage-compositions of the matte, etc., are not directly comparable for determining the rate of elimination of the impurities; and, in the absence of exact weights (which in such an operation could not be obtained), it is necessary to determine the relation between the impurities and the copper with which they are combined at various stages, in order to get data that are comparable. Owing to a portion of the copper being removed in the slag, etc., the weight of copper in the converter is not a fixed quantity, but.it is sufficiently approximate to permit very reasonable comparison. The analytical data given by Mr. Van Liew, reduced to this basis (a ratio between the impurities and the copper with which they are combined), are shown in the table on page 958. From this table it will be evident that Mr. Van Liea&apos;s conclusions as to the source of heat at digerent stages are not quite correct. During the first 10 minutes, no iron is scorified, the heat being derived from the oxidation of the sulphur, of which 7 per cent. of the total is removed in this time. Prom

Jan 1, 1904

By K. M. Myles

The vapor pressure of palladium over a series of Rlz-Pd alloys has been measured by the torsion-effusion method. The thermodynamic properties of the alloy system at 1575=K have been calculated from the vapor pressure data. The activities and the free energies of formation exhibit large positive deviations from ideal behavior. The enthalpies of formation are endother-mic. The entropies of formation are positive and larger than the ideal entropy of mixing. All of the thermodynamic properties suggest that a strong tendency toward phase separation exists in the solid solutions. The possible origin of the phase instability and the various factors that influence the thermodynamic properties are discussed. RECENT studies of the thermodynamic properties of alloys of palladium with nontransition elements have indicated that a significant contribution to the enthalpy of formation is related to the redistribution of the conduction electrons upon alloy formation.&apos;-&apos; The present work was undertaken to ascertain the importance of this contribution in Pd/transition-metal alloys. The Rh-Pd system was chosen for this investigation for several reasons: 1) The thermodynamics of the system were unknown. 2) Rhodium and palladium are completely soluble at high temperatures; below 1118OK the solid solution becomes immiscible.&apos;, 3) The difference in magnitude between the vapor pressures of rhodium and palladium permitted the use of an existing effusion apparatus. 4) Additional information was known about the alloy system that would facilitate the interpretation of the thermodynamic results. EXPERIMENTAL PROCEDURE The thermodynamic properties of the Rh-Pd alloy system were calculated from the vapor pressure of palladium over solid palladium and over several solid Rh-Pd alloys. The vapor pressure was measured by means of the torsion-effusion apparatus that has been described previously. In this method, an effusion cell is suspended from a tungsten filament inside a high-temperature furnace. Two orifices are located eccentrically such that the effusion of the vapor creates a rotational torque in the filament. The angle of rotation is directly related to the total vapor pressure within the cell. As the vapor pressures of rhodium and palladium are approximately five orders of magnitude apart," the total vapor pressure was considered to be effectively equal to the equilibrium vapor pressure of palladium. The effusion cells were made from high-purity alumina since auxiliary experiments indicated that essentially no reaction occurs between alumina and solid Rh-Pd alloys. Unfortunately, because the orifices were irregular, an accurate calculation of the Free- man-Searcy correction factors" could not be made. The constants were determined in an independent experiment where the vapor pressure of copper, as measured in the alumina cell, was compared with an accurate value of the vapor pressure, which had been determined previously.4 Depletion of palladium from the surfaces of the specimens was minimal as the deflection of the cell remained constant, for at least 15 minutes, at each of the experimental temperatures. Lattice parameter measurements of the postrun alloys also indicated that no changes in the composition of the surfaces had occurred. The alloys were prepared by arc melting the requisite amounts of the 99.99 pct pure elements. The four most palladium-rich alloys were remelted in a levita-tion furnace since complete melting of the components had not occurred in the arc furnace. All of the alloys were subsequently homogenized at elevated temperatures in sealed alumina thimbles. After heat treatment, the alloys were analyzed chemically and were in essential agreement with the nominal compositions. The thermal histories and nominal compositions of the alloys are given in Table I. Lattice parameters of the heat-treated alloys were computed, by means of the method described by Mueller et a1. ,I2 from X-ray diffraction powder patterns obtained with filtered copper radiation in a 114.6-mm-diam Straumanis-type Debye-Scherrer camera. The results, which are tabulated in Table I, exhibit a slightly greater negative deviation from Vegards&apos; law than the values reported by Raub et al.13 The diffraction lines were sharp and well-resolved and thus indicated that the alloys were homogenous. RESULTS The logarithms of the individual values of the vapor pressure of palladium were fit, by the least-squares method, as a linear function of the reciprocal of the absolute temperatures. The constants of the equations are given in Table I along with the temperature range over which the data was accumulated. The latent heat of vaporization at 298.15"K for pure palladium, calculated by the third-law method,14 showed no systematic temperature dependence. The average value of 88,920 * 20 cal per g-atom agrees favorably with the average of the results obtained in the most reliable previous investigations.15"19 The activities of palladium were computed from the vapor pressure data at 1525&apos;, 1575", and 1625OK. Consistent with the mass spectrometric study of the atomicity of palladium vapor,lg the vapor was assumed to be monoatomic. The activities of rhodium were determined by integrating the Gibbs-Duhem equation with the aid of the a function.20 In the calculations, the activities of the pure solid metals were assigned the value of unity. From the activities, the partial and integral free energies, entropies, and enthalpies of formation at 1575° K were computed; they are assembled in Table 11.

Jan 1, 1969

By B. Russell, J. R. Tuffley

The stability regions of the normal sulfate and the various basic sulfates of lead in 02-SO2 and PhS-SO2 gas atmospheres were calculated from available thermodynamic data over the temperature range 600o to 1200oC. Roasting experiments were carried out on samples of synthetic lead sulfide at various temperatures and for various roasting times. Compounds in the oxidized surface layers were identified by X-my techniques. The order in which the various reactions occurred was determined by considering the experimental results in conjunction with the thermodynamic calculations. The results of these investigations were applied to the sintering of lead sulfide concentrates, and the extent to which each of the various reactions occurred in a sinter bed was determined. PRODUCTS which may be formed during the roasting of PbS are PbS04, PbSO4. PbO, PbSO4 . 2PbO, PbSO4 . 4PbO, PbO, and Pb.1, 2 The formation of some sulfates has been studied by a number of investigators3-&apos; whose experiments have mostly been confined to the temperature range between 500" and 850°C. Culver, Gray, and spooner3 were able to isolate the reactions which formed PbSO4 and PbSO4. PbO by carefully controlling the compositions of the roasting gases. The kinetics of these reactions were studied within the temperature range 673" to 807°C. Gardner4 and Merrick5 also studied the kinetics of oxidation of PbS. Gardner disregarded the existence of basic sulfates and, as a result, misinterpreted some of his experimental data. Merrick recognized that most of the products of oxidation were mixtures of basic sulfates, but was unable to identify the individual components. Hoschek6 oxidized PbS in air at temperatures up to 800°C. The products were analyzed after roasting had proceeded for some minutes, but no attempt was made to follow the reactions in the initial stages. Consequently, no roasting mechanism was derived. He also showed that PbSO4 and PbSO4 - 4PbO decomposed slowly in air at temperatures in the region of 800°C. The stability regions of sulfates in the temperature range 500" to 850°C have been only partially determined, while practically no information is available for higher temperatures. In the lead sintering process, PbS concentrates are roasted at temperatures within the range 1000o to 1200°C. In order to investigate sulfate formation, it is necessary to determine the effects of temperature and gas composition upon the various oxidation reactions and upon the regions of stability of the various lead sulfates. Kellogg and Basu2 introduced an equilibrium diagram similar to those in Figs. 1 to 3 which provides a convenient medium for represent-

Jan 1, 1964

By Arthur Baker III

The orebodies are long bedding-plane lenses of chalcopyrite and sphalerite, associated with garnetite masses. Most of the orebodies are within a 50-ft thickness of Cambrian limestone; other Paleozoic limestones and dolomites are locally metamorphosed but only slightly mineralized. Pre-mineral faults are numerous, but shallow folds were the main ore-localizing structures. JOHNSON camp is in the northwestern part of Cochise County, Ariz., about 50 miles east of Tucson. The nearest major mining districts are Tombstone and Bisbee, respectively 27 and 50 miles to the south, and the Superior-Miami-Globe-Ray porphyry copper group, about 90 miles northwest. Like many mining camps of the Southwest, Johnson camp is said to have been worked by the Spaniards. The first production on record was in the early 1880&apos;s, when an unknown amount of oxidized copper-silver ore in the Peabody mine was mined from replacement orebodies in the Pennsyl-vanian Naco formation. From 1904 to 1911 outcropping oxidized ores in the Cambrian Abrigo formation were worked, and an estimated 100,000 tons of copper ore were shipped. In 1912 the first large sulphide orebody of the district, the Republic Manto orebody, was discovered, and in the following few years some 250,000 tons of predominantly sulphide ore were shipped. The average grade of this ore was approximately 4.5 pct Cu, 6 pct Zn, 0.8 oz. Ag, and 0.001 oz Au. The Republic, Copper Chief, and Mammoth mines were the principal producers during this period. Mining ceased in the district after 1920, and until 1943 only small-scale leasing operations were carried on. In 1943 all the mines that had been productive were acquired by the Coronado Copper and Zinc Co., the present operators, and in the 10 years since that time the district production has amounted to approximately 350,000 tons of milling ore averaging 2 pct Cu and 6 pct Zn. Most of this ore was produced from the Republic and Mammoth mines, but since 1950 a large part of the production has been from the new Moore mine. The total known production from the district, then, is about 3/4 million tons of copper and copper-zinc ore of low grade. All of this ore was produced from orebodies associated with garnetite in the middle member of the Cambrian Abrigo formation. In addition to this known production, an unknown tonnage of ore was extracted from the Peabody mine orebodies that lie in the Pennsylvanian Naco formation. Published information on the geology of the district is limited. Aside from brief references in various mining journals, only three papers on the district have been published.1-3 One of these is a U. S. Bureau of Mines report on a diamond drilling program, one is a brief paper on the general geology of the district, and the third is a report on geochemical experiments, with a section on the occurrence of the orebodies. The last two are by John Cooper, of the United States Geological Survey, who has done much detailed work in the area. Stratigraphy The rocks of the mineralized area are Paleozoic sediments ranging in age from Cambrian to Penn-sylvanian. Several disconformities are present in the stratigraphic column, the most important one being between the Cambrian Abrigo formation and the Devonian Martin formation. There are no angular unconformities. Within the district, the Paleozoic sediments lie in a fairly uniform monocline, striking northwest and dipping 30" to 50" northeast. This local monocline is part of a domal struc-ture centered in the Little Dragoon mountains to the southwest. The Texas Canyon stock, a quartz monzonite body intruded probably during the Laramide revolution, lies south of the mineralized area (Ref. 2, p. 33). The Paleozoic rocks dip away from the stock, and on the surface are separated from it by at least 1500 ft of Pre-Cambrian rocks. The outcrop pattern of the northeastern edge of the stock suggests that it may dip gently northeastward, passing below the mineralized area at moderate depth. No quartz monzonite has been found in mine workings or diamond drill holes, which reach to depths of 1000 ft. The only igneous rock found in the mineralized area is a lamprophyre dike cutting the Naco limestone in and near workings of the Peabody mine. With the exception of the lowermost beds—the Bolsa quartzite and the shaly lower member of the Abrigo formation—the Paleozoic sediments are predominantly carbonate rocks, Fig. 1. The middle member of the Abrigo formation, which contains the principal ore-bearing beds, is limestone, with thin shale partings throughout most of its 250-ft thick-ness. Near the top of this member is a sandy bed some 25 ft thick. The upper member of the Abrigo formation and the lower half of the overlying Devonian Martin formation are dolomitic, with num-

Jan 1, 1954

By C. F. Weinaug, P. M. Blair

Many difference equations used to approximate reservoir flow problems treat the phase pressures implicitly but not the mobility-density coefficients. Such difference equations are neither wholly explicit nor implicit, but might be described as mixed. Mixed equations are relatively easy to apply. But the associated time truncation error is relatively large, and when used to solve problems characterized by high flow rates, these equations may be unstable for practical size time steps. This paper outlines the development of a completely implicit difference analogue for reservoir simulation, along with a Newtonian iterative method for solving the resulting nonlinear set of algebraic equations that arise at each time step. While this implicit equation requires two to three times more work than does the mixed equation, it is shown to markedly decrease the time truncation error and to yield a stable solution for much larger time steps than does the mixed equation. INTRODUCTION Calculation of multiphase, multidimensional flow in porous media is generally accomplished by numerical methods that involve approximating systems of partial differential equations by systems of partial difference equations. The early development of difference equation techniques was directed toward the solution of linear differential systems. However, the equations of multiphase fluid flow through porous media are highly nonlinear in that mobility and density often are strong functions of pressure and saturation. Thus, solution of the flow problems by difference equations involves solving sets of algebraic equations whose coefficients change from step to step of the calculations. Current practice is to evaluate most coefficients at the beginning of a time step and then to apply difference methods well suited for solving linear problems. At least two major difficulties arise from the use of this practice. First, evaluation of coefficients at the old time level and evaluation of pressures at the new time level results in larger time truncation errors near displacement fronts than if all quantities in the distance derivative were evaluated at the same time level. Second, evaluation of mobility coefficients at old time levels results in an unstable difference equation in regions of high flow rate. The first of these difficulties often results in optimistic recovery behind the displacement front, and the second requires the use of small time steps or special techniques in solving coning problems1 or problems of gas percolation.2 Evaluation of all quantities in the distance differences at the new time level results in a completely implicit difference system. Such a difference system has a lower time truncation error than equations in which mobilities are evaluated at the old level and pressures evaluated at the new level. The algebraic equations resulting from the fully implicit difference equation are, in this case, nonlinear and require some iterative method for their solution. This paper develops fully implicit difference equations for two-phase flow in porous media, describes their solution by Newtonian iteration, and gives examples of problems more easily solved by the new method than by previous methods. EVOLUTION OF DIFFERENCE EQUATIONS FOR NONLINEAR PROCESSES The completely implicit difference equation used in these calculations results from evolution beginning with explicit difference equations, proceeding through what we will call "mixed" equations, and arriving now at a completely implicit equation. Let us illustrate the evolution by considering different analogs of the nonlinear equation

Jan 1, 1970

By R. V. Higgins

This paper presents a computer method to obtain the shape factors and equal cell volumes of the channels for any well spacing pattern from a potentiometric model. By using this program the authors have processed the data for the seven-spot, direct line-drive and the staggered line-drive patterns. The data for the five-spot pattern had been previously processed by a noncomputer method and are included for completeness. The shape factors and volumes for the channels are presented in tables for those who want to use them to process data using their own permeability relationships and viscosities of their reservoir oils. The authors have used the data and sets of representative permeability curves to process sample calculationr of waterflood performances. The comparison of the calculated results shows that the influence of well spacing is small. The permeabilities of the reservoir rock to oil and water had a greater influence on oil recovery for a given pore-volume throughput of water than the well spacing pattern. The more water-wet the reservoir rock, the better the possibility of permeabilities which are conducive to good recovery. The viscosity of the reservoir oil also influences the recovery more than the well spacing pattern. The reduction in the percentage recovery of oil with increase in viscosity of the reservoir oils is small when oil viscosities are in the range of 0.1 to 3. Above this range the reductions in recoveries are extensive. Sample comparisons of the time required for different patterns to recover the oil are presented. Results of an example calculation are given to show the effect of the permeability profile on recovery. INTRODUCTION The effect of well spacing pattern on the recovery of oil when flooding with either gas or water has been studied by many investigators. Muskat et al.1 presented an analysis using conductivity, sweep efficiency and unit mobility to the time of breakthrough. Dyes et al.2 used experimental techniques (X-ray shadowgraphs) and different mobility ratios. They presented quantitatively the relationship between mobility and sweep efficiency at and after breakthrough. Hauber3 presented a method to predict waterflood performance for arbitrary well spacing patterns and mobility ratios. Craig et al.,4 using techniques similar to Dyes et al. to determine sweep efficiency for a five-spot pattern, added the use of relative permeability curves at breakthrough and thereafter. Douglas et al.5 sed rela- tive permeabilities and continuously changing saturations throughout the entire five-spot flood pattern. In obtaining their solutions they used finite-difierence equations. Hig-gins and Leighton6,7 also used relative permeabilities and continuously changing saturations throughout the pattern before and after breakthrough. They employed techniques that process a flood-pattern calculation on the computer in about one minute. The methods of Douglas et al. and Higgins and Leighton both checked closely the laboratory results for a wide range of mobility ratios. This paper presents some sample performances calculated by the Higgins and Leighton method that show the effect on recovery of different permeabilities and viscosities using the seven-spot, the line-drive and the staggered line-drive, as well as the fivespot flood pattern. No previous paper has presented these data using different permeability curves and continuously changing saturations throughout the flood patterns. The paper also presents (1) the results and analyses of the flood-pattern prediction, (2) the computer techniques for determining the shape factors and volumes from the potentiometric models for the foregoing flood patterns, and (3) the shape factors and volumes of the channels of the flood pattern in the event reservoir engineers may like to process waterflood calculations using their own permeability curves and reservoir oils. DESCRIPTION OF METHOD VOLUMES AND SHAPE FACTORS The use of channels taken from a potentiometric model (see Fig. 1) to aid in calculating the performances of water floods of nonlinear patterns has been thoroughly explained in the literature.0,7 Therefore, very little theory, discussion, or proof regarding this phase will be repeated in this paper. The computer method presented in this paper to calculate the volumes and the shape factors of the channels of potentiometric models employs the trapezoidal rule for the volumes and the Pythagorean theorem (the hypotenuse equals the square root of the sum of the squares of the two sides of a right triangle) for the shape factors. In calculating the volume of a channel, the area of each cell in the channel is determined and then multiplied by the thickness to obtain the volume. In determining the areas of the cells, trapezoids are constructed whose vertical sides are spaced Ax apart, as shown in Fig. 2. The length of the sides is the difference between an ordinate cut off by the top and bottom of the cell — usually equipo-tentials. The coordinates of the points along an equipo-tential or streamline are obtained by Lagrange&apos;s8 equation of interpolation for which the constants are coordinate points at the intersections. Three intersections for con-

Jan 1, 1965

By Hans Lundberg

Jan 1, 1927

By D. S. Choi, R. Stefanko

There are a number of complex factors that influence the effectiveness of anchorage to maintain tension in rock bolts. However, a plastic analysis of the anchorage site employing certain simplifying assumptions with application of the Mohr-Coulomb criterion appears to explain the observed phenomena. Such an analysis has been made and a correlation sought with field and laboratory tests. Field tests were made in an anthracite mine in eastern Pennsylvania and included pull tests and long-term tests of a variety of anchorage devices in two basic lengths, 30 and 42 in. in two widely differing seams. Performance is reviewed for wedge, expansion shell, and resin anchorage. Laboratory tests duplicated many of the field conditions but in addition compared the performance of shells with normal and reversed serrations. This performance was compared with the predicted results from the plastic analysis. One of the major problems in conducting long-term underground tests is the selection of suitable instrumentation. All installed bolts were fitted with spherical and hardened washers to insure the best possible torque wrench readings. In addition, commercially available load cells were used. Finally, the performance of a specially developed strain-gage-equipped ring cell is viewed. Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, there has been a lag in development of suitable instrumentation that is simple to install and read out, sensitive, durable, reliable, safe, and economical in evaluating the effectiveness of a bolt over long periods of time. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At The Pennsylvania State University in the Dept. of Mining, research has been conducted for a number of years to measure bleed off in carefully controlled laboratory experiments as well as in underground investigations."-&apos; Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be con- ducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised. Bolts are being used for a greater variety of purposes in mining. Suspending wire sideframe belt conveyors from roof bolts is a common application. The suspension of a monorail transportation system presents yet another. One such system has just been installed in a recently reopened anthracite mine and is presently being evaluated under production conditions. Preliminary studies revealed that a considerable cost reduction was possible by suspending the monorail on bolts anchored in the top. The monorail was to be installed under two widely differing conditions—a competent sandstone above the Buck Mountain seam and a softer shale top above the Skidmore. The type of anchorage device, length of bolt, and long-term performance, consistent with economy and safety, had to be established for the installation once the decision was made to suspend the system on rock bolts. This paper describes some of the testing procedures leading to a final selection. Theoretical Analysis of Expansion Shell Anchorage A detailed look at an expansion shell assembly might shed some light on the factors involved in the design of a suitable shell, Fig. 1. When a bolt is rotated, the tapered plug is forced downward, expanding the leaves laterally to grip the sides of the hole. Two friction surfaces are present: (1) the interface of the plug and leaf and (2) the interface between leaf and rock. The relationships of these friction planes, geometry of expansion shell, and properties of the rock are important in the design of an expansion shell. Therefore, an analysis assuming the rock to behave as a rigid plastic material with its yield governed by the Mohr-Coulomb criterion was made." Furthermore, the effect of friction between the leaf and rock produced by serrations was analyzed.

Jan 1, 1971

By R. S. Shoemaker, F. W. McQuiston

CARLIN GOLD MINING COMPANY 1974 Operating Data to October MINE LOCATION: 40 miles from Elko, Nevada ORE DESCRIPTION: Gold with minor amounts of mercury occurring in siltstone and carboniferous limey shales. TYPE OF MINE: Open pit ORE HAULAGE TO MILL: By trucks up to a distance of 12 mi1es MILLING CAPACITY: 2500 tons per day ORE GRADE: 0.20 oz per ton oxide ore 0.25 oz per ton carbon type ore PRODUCTS: Gold bullion 993 fineness, by product quicksilver RECOVERIES: Oxide ore 887&apos;0 Carbon ore 83% POWER FOR GRINDING: 7 Kwh/T POWER, other than grinding: 14 Kwh/T WATER SUPPLY: Pumped from wells 2- 112 miles through 13,000 ft of 8" buried pipe 6 ft underground. Consumption 0.60 tons of new water per ton of mill feed. TAILINGS: By 10" woodstave pipe a distance of 2500 ft to mine waste filled dam. RUNNING TIME: 10 ft x 10 ft mill on oxide ore, 98% 7 ft x 8 ft mill on carbon ore, 937&apos;0 Principal causes of lost time, power outages and problems of feeding gaseous chlorine to carbon ore agitators. LABOR, TONSIMAN SHIFT: See detailed data sheet ILL BUILDING DESCRIPTION: Framed structural steel with sandwich type walls of marine plywood, then packaged pre - fabricated insulation and outer sheeting of galvanized corrugated steel.

Jan 1, 1975

By K. C. Strebig, C. W. Schultz, A. A. Selim

The effect of some organic additives in diamond drilling of quartzite was investigated in the laboratory. The drill was designed to measure the rate of penetration, the thrust, and the torque and to record each as a function of the distance drilled. A statistical plan was followed throughout the investigation and an equation representing the bit performance was derived from the mathematical theory of reliability. The drilling torque was found to increase with the use of additives while the sliding coefficient of friction and the wear coefficient decreased. The energy per unit volume consumed was found to increase with the use of additives. A hypothesis explaining the effects achieved with the additives is given. INTRODUCTION For some time researchers have attempted to increase drilling efficiency by adding certain agents to the flushing medium. Much of this interest is the result of the observations of Rehbinder, Shreiner and Zhigach1 They postulated that "...in processes for the mechanical destruction of solids, a region of increased crack formation is created in the deformed layers adjoining that surface of destruction, forming the predestmction zone. The surrounding medium (for example, a liquid) which wets a given solid will penetrate the embryo microcracks of the predestruc-tion zone. Increasing the molecular affinity of this liquid for the surface of the solid considerably facilitates the deformation and destruction by softening the solid in the zone of increased crack formation. In this manner, the hardness or strength of the deformed body is decreased by the influence of the penetration of the liquid into the predestraction zone." This is known as the "Rehbinder effect". Rehbinder&apos;s work has prompted many investigators to examine the effect of additives on the mechanical destruction of rocks. Engelmann, Terichow and Selim reported that the maximum penetration of the rock by a diamond point in a solution environment was at the isoelectric point of the solution.* Robinson reported that his results did not appear to support the theory of Rehbinder.3 Joris and .McLaren suggested that additives with surface tension lower than water will be more efficient in cooling the diamonds.4 Their effectiveness in removing the fine cuttings from the face of the bit will also improve the efficiency of the system. They reported an improvement in impregnated bit life and penetration rates with the use of soluble oil additives. In contrast, Long and Agnew, drilling with surface set bits, reported that lubricating agents increase bit temperature and wear.5 A significant change was reported6 in the mechanical properties of rock with polar additives. It was concluded that this change in the mechanical properties of the rock in the presence of the additive is due to the rock hydrophilic properties. Ethylene glycol, glycerine and anionic detergent were selected for this investigation because their surface tension is lower than that of water. The surface tension of these additives for the concentrations studied was 42 to 75 percent of the surface tension of water. A low surface tension additive would wet the surface of the diamonds more easily and hence would be more effective in cooling the diamonds. Another characteristic of these low surface tension additives is their effectiveness in removing the cuttings and preventing the flocculation of the formed particles in the drilling process. This article summarizes the results of an investigation performed at the laboratories of USBM, Twin Cities Mining Research Center. The objective of the investigation was to study the over-all effects of some organic additives on the performance of diamond impregnated bits in atmospheric drilling conditions only and not in downhole pressured conditions.

Jan 1, 1970