Search Documents

By B. P. Mulcahy

When the phrase "selection of coal for carbonization" is used, there is always the implied continuance of thought "to make good coke.'' The reason for this, of course, lies in the fact that, in almost all instances, when coal is carbonized coke is the principal product. Under certain conditions the yield of gas may also be a factor, but even here it must be secondary to the coke yield, for in every instance coke represents the largest single product of the process. The importance of coke to the byproduct industry has been considerably enhanced during the past 20 years because of the continuously decreasing financial returns of all the by-products. This fact will account, in part, for the rebirth of interest and investigation in the carbonization process during the past 10 years. Many papers have been written on this subject, with naturally divergent thoughts because of the diversity of interests, but in each instance the common aim was the same—the making of better coke. Scope of Investigation In perusing this literature, the writer was struck with the constantly recurring imposed condition of asking for better coke, but with the distinct unwillingness to make any concession to temperature of carbonization. When there is a high demand for coke, the only means by which the industry can increase the quantity is to shorten the coking time by an increase in temperature, or to increase the quantity of low-volatile coal, or both; and since in many instances the percentage of low-volatile coal can be increased only in small quantities, because of factors to be discussed later, the big increase must come from shortening the coking time. When this is done most of the improvement accomplished by the selection of the coals in the mixture is lost. It is not felt necessary in this paper to discuss the advantages of minimum ash and sulphur and other materials in coal. The value of minimum contents of these materials in coke is well established. When the use of coals high in these contents is dictated, the selection of coals, as we will consider it here, cannot apply to full advantage. The scope of this paper, then, will be to discuss the factors of inherent coal characteristics and operating procedures that influence coke quality, for they are fundamentally related and both must be considered if we are to attain our objective of better coke. A study of either must embrace a study of both simultaneously. To properly evaluate the influence of the coal and to help in the selection, we must first be able to appraise the coke, and interpret fairly the influence of the process in all of its aspects. Appraisal of Coke To refer simply to the quality of coke gives no indication of what is meant, for the term is too general in its implication. An analysis of a coke is divided usually

Jan 1, 1944

By B. P. Mulcahy

When the phrase "selection of coal for carbonization" is used, there is always the implied continuance of thought "to make good coke.'' The reason for this, of course, lies in the fact that, in almost all instances, when coal is carbonized coke is the principal product. Under certain conditions the yield of gas may also be a factor, but even here it must be secondary to the coke yield, for in every instance coke represents the largest single product of the process. The importance of coke to the byproduct industry has been considerably enhanced during the past 20 years because of the continuously decreasing financial returns of all the by-products. This fact will account, in part, for the rebirth of interest and investigation in the carbonization process during the past 10 years. Many papers have been written on this subject, with naturally divergent thoughts because of the diversity of interests, but in each instance the common aim was the same—the making of better coke. Scope of Investigation In perusing this literature, the writer was struck with the constantly recurring imposed condition of asking for better coke, but with the distinct unwillingness to make any concession to temperature of carbonization. When there is a high demand for coke, the only means by which the industry can increase the quantity is to shorten the coking time by an increase in temperature, or to increase the quantity of low-volatile coal, or both; and since in many instances the percentage of low-volatile coal can be increased only in small quantities, because of factors to be discussed later, the big increase must come from shortening the coking time. When this is done most of the improvement accomplished by the selection of the coals in the mixture is lost. It is not felt necessary in this paper to discuss the advantages of minimum ash and sulphur and other materials in coal. The value of minimum contents of these materials in coke is well established. When the use of coals high in these contents is dictated, the selection of coals, as we will consider it here, cannot apply to full advantage. The scope of this paper, then, will be to discuss the factors of inherent coal characteristics and operating procedures that influence coke quality, for they are fundamentally related and both must be considered if we are to attain our objective of better coke. A study of either must embrace a study of both simultaneously. To properly evaluate the influence of the coal and to help in the selection, we must first be able to appraise the coke, and interpret fairly the influence of the process in all of its aspects. Appraisal of Coke To refer simply to the quality of coke gives no indication of what is meant, for the term is too general in its implication. An analysis of a coke is divided usually

Jan 1, 1944

By Herman Van Fleet, Frederick W. Neil, O&apos

The object of this paper is to describe the present status and possil~ilities of liquid oxygen as an explosive based upon the investigations, research and practical work of the Ingersoll-Rand Co., and of the Air Reduction Co., from early in 1922 to date. The following work was done. 1. A study of the history and physical theory of L. 0. X. as an explosive. (No attempt will be made in this paper to give the history or theory, as this has already been covered by the literature on the subject.) 2. An investigation of the use and the practice with L. 0. X. in the iron mines of Lorraine where L. 0. X. has its largest application in Europe. Although L. 0. X. is extensively employed in the iron mines of Lorraine, many of the mines using it exclusively, and blasting with it a total of approximately three million tons of iron ore per year, the fact that the mining practice in Lorraine1 is to drill comparatively shallow holes and blast only a few holes at a time, renders the data obtained there of very little value in estimating the possibility of replacing dynamite with L. 0. X. in American mining methods. In fact, in the iron mines in Lorraine, L. 0. X. replaced black powder, or its equivalent. 3. Laboratory research work on properties of absorbent materials. 4. Work in the Bureau of Mines explosive laboratory at Pittsburgh, Pa., on the properties of L. 0. 3. cartridges. 5. Practical work underground with L. 0. X. cartridges in the Kitherbee-Sherman iron mines at Mineville, N. Y. 6. Practical work in the quarries of the Calcite Quarry Co., Myers-town, Pa. 7. Practical blasting in several quarries and open-pit mines.

Jan 1, 1927

By Richard H. Olson

"Rarely in our technological society does the discovery of a new class of inorganic materials result in such a wide scientific interest and kaleidoscopic development of applications as has happened with the zeolite molecular sieves." The foregoing, the opening sentence in a landmark volume on zeolite molecular sieves by D. W. Breck (1974), is, if anything, an understatement. Zeolites were recognized as a new group of minerals in the 1750s, but it was not until 1930 that the first analysis of the crystal structure of a zeolite mineral was made. In the late 1940s research workers at Union Carbide Corp. began a program of zeolite synthesis and study which has resulted in one of the major research achievements of all time. Naturally, with the vast research and development efforts devoted to the synthetic molecular sieves, Union Carbide became concerned in the mid-1950s about its position should minable deposits of natural analogues be discovered. Zeolite minerals have diverse origins, and even a brief discussion of these is beyond the scope of this paper. The early work on zeolites was confined to igneous rock occurrences (e.g., amygdules and veins) which were formed by "space-filling;" these crystals tend to be euhedral, thereby rendering them appealing to both mineralogists and collectors. During the first year or so of Union Carbide's exploration (which began in mid-1957) attention was devoted solely to such igneous occurrences. A landmark paper by Bramlette and Posnjak (1933) heralded the potential significance of the occurrence of zeolite minerals as alteration products of vitric ash and similar materials. In the summer of 1958, full attention was directed by Union Carbide to the search for deposits of this type in the western United States. Since then, such exploration has been continu-

Jan 1, 1975

By Chas. A. Ashburner

The occurrence of oil- and gas-springs in the State of New York has been a fact of historical record since 1627, when the existence of the Cuba oil-spring was first recorded. The utilization of natural gas at Fredonia in 1821 attracted the attention of the public to the possibility of obtaining an illuminating gas by digging and drilling into the rocks. No active search was made, however, for oil or gas by the drilling of wells until after the discovery of commercial oil in Pennsylvania in 1859. In 1862 a well was drilled at Bradford, McKean County, Pennsylvania, but a few miles south of the New York state line, to the depth of 200 feet, in search of the oil-sand which had been found at Titusville, Oil City, and at other points in Western Pennsylvania. Immediately subsequent to this, other wells were drilled in search

Jan 1, 1888

By Arthur Bell

(San Francisco Meeting, September, 1915) . PRIOR to 1908 the oil production in the State of California, had been almost entirely a heavy fuel, oil, with a high flash point, hut changed within a-short period to a large percentage of refining oil with a low flash, by reason of the coming in of the Santa Maria field, the Midway field, and the increased production of the Fullerton field. This is clearly shown in the following tabulation of California's production: Year Barrels . Below -20° Be, Above 20° Be,, Per Cent_ Per Cent. 1905 48,307,000 90 10 1910 77,698,000 SO 20 1912 90,075,000 6o 31 1914 10:3,600,000 47 53 The bringing in of these high percentage's of light oil with their dangerous low flash and the increasing demand for the refined products necessitated the devising of some cheap and efficient means of quickly separating the lighter elements either in the field or at the main distributing points; also it became necessary to remove the excessive percentage of water which many of the light oils carried in emulsion.

Jan 9, 1915

By Stanley Herold

Considerable interest has been shown, during recent years, in the possibilities of developing oil fields in the South American Republics, now that the exhaustion of our present fields can be seen in the not very distant future. The demand for fuel oil and its products has been increasing far more rapidly than our increment of production during the last few years. Increase of consumption has been largely curtailed by the lack of sufficient supply. The main factors that have contributed to our previous neglect of the southern fields have been as follows:, (a) Lack of sufficient demand for the product. (b) Competition with producing fields, having large production, low cost, and better geographical position, such as Tampico, Mexico. (c) Greater interest in home fields with ready market at hand. (d) Our ignorance of southern economic and geologic conditions, clue to the distance between those areas and our financial centers. (e) Economic conditions in the southern countries, necessitating high costs of exploration and exploitation of the fields.

Jan 9, 1918

By R. U. Fitting, A. C. Bulnes

Field experience with limestone and sandstone production indicates the existence of wide differences between the reservoir behavior of these two types of formation. Little attention appears to have been given to the separate study of the flow of fluids and the retention of fluids in limestones. This paper presents data and arguments to demonstrate the existence of a difference between the two types of formation, and urges the separate intensive investigation of limestone reservoirs. AH experimental data presented pertain to dolomitic limestone formations in west Texas and New Mexico. Two kinds of Porous media are recognized— intergranular and intermediate. Intergranular rocks are those in which the porosity and permeability are determined by the geometrical properties and the sorting of the sedimentary units; intermediate rocks, those in which there is no direct relationship between grain properties and the porosity and permeability. Limestones in general are intermediate media. The partial relationship between porosity and permeability of any class of Porous media is represelried by an area of .finite extent and definite shape on the permeability-porosity plane. The horizontal and vertical variations of porosity and of permeability in limestone and sandstone formations are discussed and compared. Comparisons are made of connate-water content, the relative permeability-saturation relationship, and capillary phenomena in the two kinds of rocks. A number of tentative conclusions are drawn relative to the reservoir properties of lime- stones; in particular, (I) dolomitic limestones are oil bearing and apparently are oil productive in zones of permeability less than 0.1 millidarcyj and (2) primary depletion (by gas expansion) oil saturations may be lower in dolomitic limestones than in sandstones. Introduction It is well known that the reservoir performance of limestones displays numerous irregularities when compared with that of sandstones, and that the departures from "normal" behavior of limestones are more frequent and generally more marked than in sandstones. This is particularly true of fractured limestones and those that have undergone considerable development of secondary porosity' A review of the literature of production research published during the past 15 years reveals a startling absence of theoretical and experimental investigations directed specifically toward explaining and predicting the performance of limestone reservoirs, even. though such problems as the prediction of water encroachment and the estimation of ultimate recoveries continue at the "inspired guess" stage. By far the greater part of the experimental data reported pertain to measurements on sandstone core samples, while the theoretical studies, almost without exception, are developed from the assumption of an ideal porous medium and therefore seldom are applicable to limestone formations. The chief cause of this situation appears to be the common belief that, to all practical intents and purposes, sandstones and the majority of producing limestone formations

Jan 1, 1945

By Walter Harvey Weed

Introductory.............449 Summary oF Types............452 I. The Virgilina Type...........452 The Virgilina mines...........452 Location.............452 History.............453 The rocks of the district..........453 The veins.............454 Notes on the mines.... 458 The Holloway. 458; Yancey and Durgy. 465 ; Copper World. 467 ; Frazier. 467 ; Thomas. 467 ; Anaconda. 468; Blue Wing. 468; High Hill. 472; Dorothy.......474 II. The Gold Hill Type...........474 The Gold Hill mine...........475 Location.............475 History............• 475 Surface improvements.......... 476 The rocks............478 Vein.phenomena...........478 Character of the ore..........481 Origin of the ore...........481 Notes on the mine.workings.........482 Other occurrences of ore-deposits of the Gold Hill type.. .. 483 III. The Ducktown Type..........484 The Ducktown mines...........485 Other examples of the Ducktown type....... 494 Alabama mines...........494 North Carolina examples : Ore Knob.......496 Virginia examples..........497 IV. The Catoctin Type.. ......... 498 General characteristics,......... 498 The Linden district...........499 General distribution of the Catoctin type.......503 Introductory. In the early history of this country the existence of copper in the Appalachian region was well known. but no mining mas attempted until the discovery of the Ducktown deposits in

Jan 1, 1901

By W. H. Bassett, C. H. Davis

The late J. P. Sparrow, chief operating engineer of the New York Edison CO., carried out a series of practical tests on condenser tubes of several copper alloys and reported on the results to the Association of Edison Illuminating Companies at its meeting in September, 1913. In the preparation of these tubes the senior author had the pleasure of cooperating. Copper-zinc alloys in the proportions of 60-40,70-30,80-20, 90-10, and Admiralty metal, which is in effect 70-30 with 1 per cent. of tin, were tried. Monel metal and several copper-nickel alloys, and 8, 5, and 3 per cent. aluminum bronze were also tried. At the time of this report, the aluminum bronze had been in service for 4 1/2 years and seemed to be giving especially good results but later it began to fail and showed no substantial improvement over Admiralty metal. Monel metal was unsatisfactory and the nickel alloys apparently did not give better service than the Admiralty alloy. Previous to the publication of the report, and after considerable discussion, it was agreed that a test where tubes of different kinds could be under laboratory observation would be advisable, so the apparatus described here was set up in The American Brass Co.'s Waterbury Laboratory. This was fitted with tubes of copper, brass, bronze, nickel silver, cupro-nickel and other alloys, and the test started on Oct. 11, 1912. Salt water from East River, New York harbor, was barrelled and transported to the laboratory for the test. A fresh supply, completely replacing the water in service, was obtained at the end of each six months period. Plan of Procedure In general, the procedure was to inspect the tubes at short intervals and to remove those that had begun to leak. The tubes removed were carefully examined and a photographic and microscopic record of the

Jan 1, 1925

By Reno Sales

INTRODUCTION. THE geology of Butte possesses especial interest on account of the magnitude of the ore deposits, their extraordinary richness and persistence in depth. Since its discovery in the early 60's the district .has yielded, in round numbers, 6,000,000,000 lb. of copper, 260,000,000 oz. of silver, 1,250,000 oz. of gold, and a large but not definitely known number of pounds of zinc. This enormous metal production has been derived from an ore tonnage estimated roughly at 65,000,000 tons. At the present day, most of the important mine shafts have reached a depth of. 2,400 ft., while several are more than 3,000 ft., deep. At these-great depths rich bodies of copper ore are being exploited, showing no diminution in metal content as compared with the ores of the higher levels. The present (1913) daily rate of production is approximately 14,000 tons, of which 13,250 tons may be regarded as copper ore, although a small percentage of this is minable only because of the presence of

Jan 8, 1913

Jan 3, 1953

By B. F. Tillson, C. M. Haight

I. General Remarks..........................723 1. Location............................723 2. Characteristics of the Orebody..................725 (a) Mineralogical (b) Shape, Strike, Dip, Size, Etc. (1) Ore (2) Country Rock 3. Historical Sketch........................725 11. Mining Method..........................726 1. Outline of Methods Now in Operation............... 726 (a) Stopes (b) Fill . (c) Pillars (d) Slices (e) Transportation (f) Miscellaneous 111. Mining Operations........................727 1. Shaft..............................727 (a) Sinking (b) Dimensions and Equipment, Sketches (1) Size, Inclination. Direction, Etc. (2) Timbering (3) Stations (4) Track (5) Hoisting Equipment (a) Skips (b) Engines and Ropes (c) Idlers (d) Man Cars (6) Loading Pockets (a) Operating Figures (7) Headframe

Jan 1, 1918

By T. D. Yensen

It is safe to say that of all the different materials that go to make up electrical machinery, iron is the most important. Upon its magnetic and electrical quality depends not only the efficiency of the machine but, to a very large extent, the cost. Aside from the mechanical strength, there are three characteristics of iron that are of importance in this connection, viz., magnetic hysteresis, electrical resistance, and magnetic permeability. In the homopolar machine, where the magnetic flux is unidirectional, permeability is the only important factor, but in all other machines the flux is reversed in one or more parts and causes losses due to hysteresis and eddy currents. The eddy-current loss depends largely upon the electrical resistance of the iron; the higher the resistance the lower the loss, under otherwise identical conditions. These hysteresis and eddy-current losses cause heating of the machine, and as they depend upon the magnetic density in the iron, this density must be regulated so that the heating shall not be excessive. If the hysteresis and eddy-current losses and the permeability of the magnetic circuit will permit an increase in the magnetic density, or, in other words, a decrease in the amount of iron, this in turn will mean a decrease in the amount of copper needed, with a consequent decrease in the copper loss. It is thus seen that, indirectly as well as directly, the above characteristics have an important bearing on both the efficiency and the cost of electrical machinery. In general, it may be said that iron for electrical machinery should have the following characteristics: (1) low hysteresis loss, (2) high electrical resistance, and (3) high permeability. These are the characteristics that investigators have been striving to attain since electrical machinery first came into use. Until the beginning of the present century, Swedish charcoal iron was regarded as the best grade of iron for magnetic purposes, and even now it ranks high among the various grades used. About that time Sir Robert Hadfield1 produced a number of iron alloys that revolution-

Jan 1, 1916

By I. C. White, G. H. Ashley, J. A. Bownocker

Among the rich mineral deposits of the great Appalachian field, the Pittsburgh coal bed stands pre-eminent. Other coal beds may cover a wider area, or extend with greater persistence, but none surpasses the Pittsburgh seam in economic importance and value. It was well named by Rogers, and his able assistants of the First Geological Survey of Pennsylvania, in honor of the city to whose industrial growth and supremacy it has contributed so much. Whether or not the prophetic eye of that able geologist ever comprehended fully the part which this coal bed was to play in the future history of the city that gave it a name we do not know; but certain it is that the 7 ft. of fossil fuel, which, in Rogers' time, circled in a long black band around the hills and, overlooking the site of Pittsburgh from an elevation of 400 ft. above the water of the Allegheny and Monongahela, extended up the latter stream in an unbroken sheet for a distance of 200 miles, has been the most potent factor in that wonderful modern growth that has made the Pittsburgh district the manufacturing center of America, and that bids fair to continue until it shall surpass every other district in the world, even if it does not now hold such primacy.' The Pittsburgh coal bed stands today as probably the largest contributor of wealth of any single mineral deposit in the world. If it is not, what other deposit is? It has contributed to Pennsylvania alone more than 2,500,000,000 tons of high-grade coal worth nearly $4,000,000,000; since 1910, it has added more than $2,500,000,000 to the value of Pennsylvania's mineral output. In 1920, this bed2 contributed 127,227,000 tons of coal as follows: Pennsylvania, Pittsburgh district........................ 38,245,000 Connellsville district................................. 34,095,000 Weatmoreland-Ligonier district........................ 16,107,000 88,447,000 West Virginia, Fairmont district........................ 15,571,000 West Virginia-Ohio, Panhandle No. 8 district............. 21,128,000 Maryland-Potomac (Est. one-third of production)......... 2,081,000 38,780,000 Total........................................... 127,227,000

Jan 1, 1927

By M. R. Campbell

Coal is the geological product of entombed vegetal tissues. This view of its origin led Stopes and Wheeler to define it as "mummified plants." They evidently intended this term to be used in a broad way and to mean the preservation of the organic material, as such, regardless of the means employed to accomplish the purpose. The term " coal" should be regarded, therrfore, as broadly generic, and applicable to all accumulations of vegetal tissues as soon as they are covered and protected either by water or by earthy material. In this sense peat should be regarded as the first stage of coal formation and the term coal should include the resultant products of transformation in all other stages of the process until they have lost all resemblance to the original matter from which they were derived. If this idea of the development of coal is accepted and it is admitted, as the geologists claim, that the forces which produced this transformation of the coal have been active since vegetation began to grow upon the land, and are still in operation, it is obvious that somewhere in the world there are all gradations of this material from peat just forming in the swamps of today to graphitic anthracite which presumably marks the most advanced stage that can be recognized with certainty as belonging to the series. Some of these coals, particularly those occurring in the upper part of the series, are fairly well known because they are the ones that are most widely distributed and have been mined and utilized most extensively. On the other hand, the coals in the lower part of the series are but little known because they are not so abundant and, owing to their relative inefficiency, have been only slightly exploited and utilized, especially in regions where the better coals are abundant. The result of these conditions is that much research work has been done on coals of the higher ranks and a great body of facts regarding their physical and chemical properties and the uses to which they are best adapted has been accumulated, but little information is available regarding the coals of the lower ranks. Many able scientists, particularly chemists, have attempted to bring some order of the chaos of coals of various compositions and uses by

Jan 1, 1930

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric pressure and by heat transferred to it from rock at high temperature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. METHODS Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1941

By Joseph B. Umpleby

WHEN the Cushing field flooded the oil market in 1914 and 1915 with a daily output equal to nearly one-third of the world's production, the situation was soon corrected by increased consumption, and the price of crude oil rose from 45 c. per barrel in, February 1915 to $1.10 in December of the same year-the highest price paid in the Mid-Continent field up to that time. The intensive search for oil during the following seven years failed to disclose a single new ,field equal to Cushing, and many observers concluded that the rapidly increasing number of wells contributing to the world's output, each declining roughly 20 per cent. a year, combined with the rapidly increasing con¬sumption of petroleum, made it highly improbable that any field would; be found again sufficiently large to seri¬ously affect the oil market. That seven exceptional fields should then be discovered simultaneously is a remarkable coincidence. Long Beach, Santa Fe Springs, and Powell, each exceeded Cushing in daily output and reached the apex of their production during a year when Burbank, Tonkawa, - Smackover and Huntington Beach each contributed several times the daily output of the average new pool. This unexpected and tremendous flood of flush production could only have the effect of depressing price and greatly adding to stocks throughout the country. It was particularly depressing in the Mid-Continent as the new oil from California proved of attractive refining grade and because of cheap transportation by water easily undersold Oklahoma crude in the eastern markets.

Jan 1, 1924

By E. H. Greener, M. E. Fine

The internal friction (1/Q) of cobalt Fig. 1 (measured by an electrostatic dynamic method1) near 250°C begins to increase rapidly on heating and continues to increase until 560°C, the highest tem- perature measured. In the plot of log of 1/Q against 1/T, above 250°C the data nearly fit two straight lines intersecting at 400°C, approximately the temperature of the hexagonal-cubic transformation. The higher temperature branch corresponds to an effective activation energy of 6500 cal per mole, the lower temperature branch 11,000 cal per mole. Young's modulus Fig. 2 increases approximately

Jan 1, 1959

By R. J. Cowan

In the art of cementation a controversy has been going on for years as to whether solid or gaseous carbon is the active agent in carburizing steel. More recently opinion has crystallized into a compromise to the effect that carburizing is a gaseous cementation of steel in the presence of solid carbon. The importance of this theory has a particular bearing upon the work to be described. In the art of carburizing, use is commonly made of such words as '' Catalytic" "atomic," "nascent" and "activated," in an attempt to describe the process. These words are used indiscriminately. For instance, the gas is said to be "catalytic" and carbon to be "nascent," or vice versa. In using these expressions, investigators are confirming the acceptance in their minds of the active conditions of both gas and carbon in the cementation process. Reactions at Metal Surfaces For many years attention has been directed to the consideration of reactions that occur on metal surfaces. When heated under the influence of certain metals a complex gas will be broken down and one of the constituents thereof usually found to be very active chemically in combining with the metal. The process of nitriding is an example of this type of reaction. In this case ammonia (NH3) breaks down at the metal surface and the nitrogen which is thus liberated reacts with the surface to form a nitride whereas molecular nitrogen not so liberated is inert and will not react chemically with the metal. Whatever term or terms may be used to describe such reactions, the fact remains that they are highly important and valuable in their commercial applications. Since the metal surface plays so important a part in these reactions, it is evident that any accumulation of reaction products thereon interferes seriously with the progress of the reactions. For this reason it is desirable to remove all such products as rapidly as they are formed in order to bring active gas into contact with the surface and thus facilitate the desired reactions. This is accomplished best by conducting the operation in a continuous manner, thereby causing the reacting gases to pass over the

Jan 1, 1931