Search Documents

By R. A. Morse, C. R. Holmgren

The production of oil by water flooding can be substantially increased by the maintenance of free gas saturation in the reservoir during the flooding operation. This effect is accomplished by the alteration of oil relative permeability characteristics and the occupation by gas of pore space that would otherwise be filled with residual oil. The amount of reduction In residual oil can be calculated from appropriate water-oil relative permeability characteristics. This paper presents experimental data in support of the foregoing conclusions and an example of the calculations. The microscopic pore saturation concepts of the mechanism are discussed. A method of practical application to field floods is presented together with discussion of certain limitations. INTRODUCTION The presence of free gas has been reported by a number of investigators to significantly affect the oil recovery which can be obtained from sandstone flow systems by water flooding.1,2,3,4,5 The effect of gas, noted in every instance, has been to cause lower residual oil saturations than could be obtained by water flooding the same systems in the absence of free gas. The degree of improvement in recovery has been observed to vary widely, depending on the systems used and the conditions of the tests. The increased oil recovery obtained because of the presence of gas during a water flood has been variously attributed to changes in physical characteristics of the oil, selective plugging action of the gas, inclusion of oil mist in the free gas phase, and the additional sweeping or driving action of the free gas. All but the first of these suggestions imply changes in the displacement mechanism. The change in viscosity and inter-facial tension of the oil phase, within the pressure range used for all the experimental work, is certainly not sufficient to account for the differences in residual oil saturation noted dess there is a drastic change in the displacement process. One other effect which logically seems capable of causing differences in residual oil saturation of the magnitude noted in the experimental work is that of simple replacement. In a water-wet system containing oil, water, and gas, it is to be expected that the gas will exist inside the oil. This is the position of minimum free surface energy, since the gas-oil interfacial tension will be less than the gas-water interfacial tension. There is no apparent reason to expect that the existence of free gas within the oil phase should alter the saturation at which the non-wetting phase (now oil and gas) should become discontinuous and hence trapped so as to be unrecoverable by direct displacement by water. If this is the situation, then trapping of a certain percentage of gas saturation during water flood should result, at infinite water-oil ratio, in a like reduction of oil saturation below that attainable by flooding in the absence of free gas. It is visualized that the gas will exist as bubbles inside the discontinuous residual oil as illustrated in Fig. 1, with the size of the oil bubbles being substantially unchanged due to the presence of the gas. As a practical matter, it can be anticipated that the presence of a free gas saturation inside the oil phase will reduce the relative permeability to oil which will exist at any particular water saturation. This reduction will be caused by two factors — -the addition of the gas-oil interface, and the reduction of area available for oil flow in the pores containing gas. This reduction in oil permeability at any particular water saturation will result in water breakthrough at a lower water satu-

Jan 1, 1951

By D. Harrington

ALTHOUGH statistical data are not at hand to justify definite statements as to progress in health, and safety in the mining and allied industries during 1935, it now appears probable that in both coal mining and in metal- mining the rate of accident occurrence as well as the absolute number of accidents will show slight increases for the year. Much: of the responsibility for this increase lies with the large number of relatively. small mines that have more or less recently come into existence, partly because of 'the lack of opportunity for work in the larger mines for large numbers of unemployed miners, and partly due to increased prices for some of the mineral products, especially gold. In general, the larger long-established nines show downward accident trends and this is decidedly encouraging as it shows that where mines are operated with real efficiency, mining can be done in relative safety.

Jan 1, 1936

By AIME AIME

H OWEVER extensively water-lines may be laid in the mine for fire fighting purposes, there are still, usually, points being worked temporarily, development, stoping or other work of a temporary or incidental nature where it is considered that the expense of laying fire-lines is not warranted. While the laying of water-lines in some sections of the mine may not be warranted, in most metal mines it is necessary to lay an air-line to all working places. In the mine of the United Verde Extension Mining Co., at Jerome, Ariz., advantage has been taken of this fact by providing a means of by-passing the water at the end of the water-line into the air-line in case an emergency arises. By this means the 2-in. air-line can be quickly converted into a water-line for fighting fire which might otherwise be beyond the reach of the water-lines.

Jan 1, 1930

By D. de Fontaine

A convolution procedure is described for obtaining an analytical expression for the composition profiles of solute concentration:; in binary solid solutions. The free energy of solutions containing such compositional inhomogeneities can then be evaluated and the stability of spherically symmetric clusters (G.P. zones, for short) us a function of their radii and central compositions can be studied accordingly. Two characteristic zone radii are defined: the minimum radius (RM) corresponding to the smallest zone for which growth is energetically favored over dissolution, and the critical radius RK) corresponding to zones associated with the minimum work of formation. The values of RM and RK coincide at the two classical limits of nucleation and growth and spinodal decomposition. As the spinodal is approached, however, RM and RK diverge increasingly and it is proposed that the initial] decomposition morphology is governed more closely by the minimum, rather than by the critical radius since the former possesses no singularity within the m eta stable phase boundary. Reversion is briefly discussed in the light of the foregoing and it is shown that a set of reversion temperatures located between the coherent miscibility gap and the coherent spinodal must correspond to a given distribution of low temperature zones. SINCE the early works of Guinier1 and preston,2 the kinetics and morphology of GP zones have been studied extensively, see Ref. 3, for example, for a recent review. Nevertheless, a completely satisfying theoretical treatment of the decomposition of meta-stable or unstable binary solid solutions is still lacking due to the almost unsurmountable mathematical difficulties that one encounters in attempting to solve the pertinent diffusion equation which, in principle, describes the whole process. This equation, first derived by Cahn for the initial stages of spinodal decomposition,4 is a nonlinear partial differential equation of the fourth order in anisotropic space, a general analytical solution of which is completely out of the question. From this equation, some prediction can be made, however, concerning the later stages of spinodal decomposition5 and a recent numerical solution6 of the equation in the case of one- and two-dimensional composition modulations of a solid solution inside the spinodal has led to the following considerations: the sinusoidal morphology7 is to be expected only for solutions of average composition c, located near the center of the coherent miscibility gap.8 For solutions with co closer to the spinodal decomposition, depleted shell zones9 should constitute the first recognizable decomposition product, later evolving to iso- lated, enriched preprecipitates in a uniformly depleted matrix as this must, in all cases, constitute the final metastable morphology, barring, of course, loss of coherency and change in crystal structure. In agreement with the qualitative description of Bonfiglioli and Guinier,l0 it thus appears that the various models discussed by previous authors are, in fact, idealized successive stages of the general decomposition process. Unfortunately, corresponding calculations for a solid solution outside the spinodal are not yet available because of two additional difficulties: it is essential that the diffusion equation be solved in three-dimensional space, and furthermore, one must include in the equation an appropriate "source term" describing the statistics of the creation of composition fluctuations required to trigger the nucleation events. At present, a general treatment of this problem does not appear to be tractable. Nevertheless, by using a modelistic approach, i.e., by selecting a priori certain composition variation profiles and by evaluating their associated free energies, one can draw certain conclusions relative to the stability of these isolated composition modulations or "zones", both outside and inside the spinodal. This is the object of the present investigation. THEORY We shall now describe a standard four-parameter spherically symmetric GP zone, evaluate its free energy according to the Cahn and Hilliard11 formula (Eq. [5], below), and plot the corresponding energy surfaces as a function of zone amplitude and radius as

Jan 1, 1970

By G. W. Form, W. A. Spitzig

The effects of hydrogen and vacuum shtering treatments on the physical and mechanical properties of arc plasma-sprayed tungsten were inuestigated. Temperatures examined ranged from 3000" to 4000°F in vacuum and 2000" to 3000°F in hydrogen for both single and duplex sintering cycles. Densities of 92 pct of theoretical density were obtained when a long-time hydrogen treatment at 2000°Fpreceded sintering in vacuum at 4000°F for 4 hr. This cycle also produced the highest ualues for modulus of rupture and bend angle. The results of this investigation point out the desirability of using a low-temperature long-time hydrogen treatment prior to a high-temperature vacuum sinter for arc plasma-sprayed tungsten. ADVANCES in the development of arc plasma-generating equipment have provided a high-temperature heat source that makes the fabrication of tungsten shapes possible by a metallizing process. Tungsten in the as-sprayed condition is very brittle. It has a density between 80 and 85 pct of theoretical density, a lamellar structure with elongated pores, and a high interstitial impurity content. To improve these properties, sintering treatments can be applied to the as-sprayed material, similar to those used for the densification of compacted tungsten powder. However, in view of the differences in the density and microstructure of as-sprayed tungsten as compared with compacted tungsten, responses to sintering were expected to be different. EXPERIMENTAL PROCEDURES The tungsten powder used in this investigation had a particle size varying from 3 to 13 p with an average diameter of 8p. The impurity level was less than 0.1 pct. The arc plasma spraying was done with an F-40 Thermal Dynamics Corp. plasma jet. Spraying was performed in air and thus required cooling of the substrate by an air blast in order to minimize oxidation. The spraying parameters employed in the fabrication of all specimens are listed below: Power input, kw 12 Arc-gas flow, cfh 95N2 + 5H2 Powder feed rate, g per min 33 Powder carrier gas flow, cfh ION, Spray distance, in. 3 Traverse rate, in. per min 30 Mandrel speed, rpm 100 Nozzle orifice, in. 7/32 These values of the spraying parameters correspond to optimum conditions ascertained in a previous study. Sintering was conducted at 3000°, 3500, and 4000°F in vacuum (< 0.1 Hg), and at 2000 and 3000°F in hydrogen. Duplex sintering treatments investigated are listed in Table I together with the designations that will be used for reference throughout this paper. The samples were fabricated by spraying onto a copper mandrel which was removed prior to sintering. The specimens used for the sintering analyses had the shape of small hollow truncated cones 1 in. high with an inside diameter varying from 0.500 to 0.125 in. and a wall thickness of 1/8 in. Specimens for bend testing were taken from hollow hexagonal prisms 1-1/2 in. high with a 1-in. diam across the flats and a wall thickness of 1/8 in. The bend-test specimens were ground to the dimensions 0.085 by 0.350 by 1-1/2 in. Prior to bend testing 0.0025 in. of stock was removed from each surface by electro-polishing. Density measurements were made by the water-displacement method. In addition, a porosimeter was used to determine the amount of interconnected porosity for representative samples. Strength and ductility were determined from recorded values in transverse bending using a cross head speed of 0.020 in. per min. The load was applied at the midpoint of a 1-in. span. The deflection data reported herein refer only to the plastic portion of the total deflection. RESULTS AND DISCUSSION The as-sprayed samples had a density corresponding to 83 pct (l pct) of the theoretical density of tungsten. Fig. 1 shows a representative as-sprayed tungsten structure.

Jan 1, 1964

By G. R. Smithson, John E. Hanway

This paper, the first of two papers covering the development of a metallurgical process for the treatment of a complex ore, describes the bench-scale experimental Program undertaken as a basis for initial process design. The results of using various potentially applicable process steps are detailed and the basis for selecting certain of these steps for Pilot-plant development is outlined. A process consisting of the steps of sulfate roasting, leaching, copper recovery, solution purification, zinc electrolysis, and brine leaching for lead recovery was recommended for further study. THIS paper describes the bench-scale development of a sulfate roasting process designed to recover copper, lead, and zinc from a complex ore. The extrapolation of the bench-scale results to pilot-plant design and the results of pilot-plant operation will be described by Lund, et al.&apos; in a subsequent paper. Several years ago, the research divisions of the St. Joseph Lead Co. became responsible for the development of a metallurgical procedure to treat a complex sulfide ore containing copper, zinc, and lead sulfides. The primary objective was to devise a procedure which would permit economic recovery of the nonferrous values. As could logically be expected, the study of conventional flotation procedures was undertaken; in addition, however, because the physical nature of the mineral association in the complex ore indicated that physical methods of ore beneficiation might not prove to be entirely satisfactory, a program also was established to investigate alternative methods of direct metallurgical treatment for recovery of the metal values. Exploratory test work by the St. Joseph Lead staff led to the conclusion that a sulfate roasting technique represented the most attractive approach for a direct metallurgical process. Sulfate roasting would provide for the selective conversion of the nonferrous values to forms soluble in conventiona1.1 leaching agents and would permit their efficient separation from the insoluble iron and other gangue materials. It should allow efficient utilization of the thermal energy available from oxidation of the sulfide raw material, and might provide an opportunity for recovering byproducts such as iron and sulfur. The decision to evaluate a selective sulfation procedure as a basic processing step also was influenced by the excellent results obtained by the St. Joseph Lead Co. in using this procedure for the recovery of cadmium from zinc sulfide concentrates. The choice of selective sulfation as a major processing step served as a basis for an extended experimental investigation of the process with bench- and pilot-scale equipment to prove its feasibility. St Joseph Lead Co., aware that Battelle Memorial 1nstitute had participated in the development of several fluidized-bed sulfate roasting procedures, asked Battelle to undertake the bench-scale development of a suitable sulfation process. This paper describes the procedure used and the results obtained at Battelle in the treatment of the complex sulfide ore. EXPERIMENTAL WORK Nature of the Raw Material. The sulfide ore deposits of interest are essentially a massive sulfide, with the indivudual ore minerals being extremely fine grained and intimately intergrown with each other and with the associated gangue. The zinc in the ore is present mainly as sphalerite (ZnS), the lead as galena (PbS), and the iron either as pyrite (Fes2) or as pyrrhotite (FeS). Table I shows the chemical analysis of various individual samples of the ore. These analyses illustrate the variability of the ore body and impose a rather severe requirement on any type of metallurgical process—that of being able to tolerate probable wide variations in the assay of the head ore. The tentative flowsheet designed to serve as a guide for the initial experimental investigation of

Jan 1, 1962

By A. E. Deruyttere, J. Van der Planken, M. Laurent, Van den Bergen

FahRENHORST and schmid1 observed that zinc single crystals work hardened less rapidly when strained in liquid air (- 185°C)than in a bath at -82°C, whereas at higher temperatures the rate of work hardening decreased with increasing temperature, as would be expected. Cadmium and magnesium showed no such decrease at -185°C. At that time the observed anomaly for zinc at liquid air temperature probably seemed insignificant. However it later was confirmed2 by experiments in liquid nitrogen (-196°C) and in the mixture solid carbon dioxide-acetone (-77"C) and therefore appeared to be real. seeger3 then suggested that the anomaly might be due to the different wetting of the zinc crystals by the cooling media. Recently a new confirmation was obtained,4 however the cooling media again were different: the rate of strain hardening was found to be lower in liquid nitrogen and liquid oxygen than in pentane cooled to various temperatures down to -126°C. Ekperiments will now be reported in which the medium surrounding the specimen at the different temperatures was the same, namely gaseous air. The single crystals were made from "Overcor 99.99" zinc. They were grown in a vertical traveling furnace on seeds of nearly the same orientations. The diameter of the crystals was 5 mm and the length between shoulders 140 mm. The brass shoulders were stuck to the crystals by means of araldite. A thin steel wire was fixed to each shoulder and served to fasten the specimen to a Houns-field tensile testing machine. The crystals with the shoulders and part of the wires were surrounded by two concentric cylindrical containers. The coolant. either liquid air or ground solid carbon dioxide, was poured into the outer container only. During cooling the containers rested on a support which was removed when the straining was started. In order to check the temperature which the crystals would attain inside the inner container, a hollow bar of zinc in which a thermocouple was fitted was first mounted in the apparatus as a substitute for a crystal. It appeared that a constant temperature, respectively - 183° and -72°C, was attained inside the bar, if a soaking time of the order of 1 hr was allowed and if the outer container was constantly kept filled. Accordingly, this procedure was adopted for every tensile test. To take account of the large scatter, fourteen tensile tests were performed with liquid air and seven with solid carbon dioxide. The orientation of the crystals and the results are presented in the table, in which the symbols have the following meaning: 1 : temperature x : initial angle between basal plane and specimen axis : initial angle between slip direction and specimen axis a : shear strain at fracture 0: average rate of strain hardening = —-——- 100 t0 and Te representing respectively the critical shear stress and the shear stress at fracture. Despite the scatter of the a- and 8— values which is of the same order of magnitude as in the work reported by Seeger and Trzuble,4 it is evident that the strain hardening rate is significantly lower at -183°C thanat-72°C. The table also contains the average values calculated from Seeger and Trauble&apos;s results at the corresponding temperatures: z.e., four results at -183oC and two at-70°, -71°C. These authors calculated 9 in a slightly different way, but this is unimportant. The agreement between the a-values shows that both sets of experiments are comparable despite the differences in experimental techniques. The rates of strain hardening also agree and it may therefore be concluded that the anomaly is not

Jan 1, 1962

By M. M. Singh, H. L. Hartman

This paper reports on the results of a fundamental investigation of the behavior of rock under impact of a chisel-shaped bit. Drop-tester studies were conducted with strain gauges attached to the rock and striking bit-edge. It was established that rock behaves viscoelastically. Little correlation was found to exist between the strain waveforms detected on the rock surface and in the bit; thus, strain-time curves obtained with transducers mounted on the bit cannot be used to explain the sequence of events in rock breakage. It is estimated that nearly 1 per cent of the total energy of the blow is expended in permanent deformation of the rock. The strain- energy distribution on a rock surface as a result of chisel impact, which follows a simple law, is presented graphically. Experiments also were conducted with gauges embedded in the rock vertically below the line of impact and at an angle of approximately 45&apos; to the vertical. No essential difference was observed in the type of wave obtained with embedded gauges and with gauges on the surface, as may have been anticipated from theory. INTRODUCTION Through the ages great strides have been taken towards improvement of the various techniques applied in the breakage of rock. Indeed, numerous applications of the rock-failure process are an integral part of present-day industry, including oil well drilling. Yet, astonishingly, little is known regarding the behavior of rock under dynamic loading or the mechanism of rock failure. The value of impact loading studies from the point of view of drilling is evident, however, and requires little elaboration because impact of a chisel edge on rock forms the basic action constituting most common methods of drilling. RELATED STUDIES Impact studies of communition and fragmentation conducted by Fahrenwald, et a1,8 Poncelet,l7 Axelson, et a1,2 Piret,16 Hartman and pfleider,ll Charles and deBruyn,5 and others have been of considerable help in understanding rock-breakage phenomena. Further insight into the basic action of drilling and penetration has been obtained by the work of Irving,13 Cherkasov and Shlyapin,6 BOrcherdt,3 Shepherd,19 Shreiner and Pavlova,20 Drilling Research Inc.7 Hartman,10 Appl and Gatley1 and several other investigators. However, knowledge concerning the stresses and strains induced in the rock and bit during impact remains scant. Recent photoelastic studies by Tandanand and Hartman (1961. 1962)22, 23 have shed light on stress distributions and Fracturing produced in plastics by chisel-shaped bits. In the field of transient strain Pulses and their role in rock drilling, the only extensive work has been performed by Drilling Research Inc. (DRI). They attached strain gauges to the shank of a bit and conducted drop-tester studies, using a die-shaped bit to obtain force-time diagrams. Their work led to the conclusion that, for a given rock type, the first peak of force occurs at a fixed level regardless of the total energy in the system, provided it exceeds a certain minimum threshold level. Further, on this basis an explanation was offered for the sequence of events in crater formation as the result of a single blow on rock. PURPOSE OF PRESENT STUDY The investigations reported in this paper were conducted in a manner similar to the DRI approach, but with the objective of determining the strain distribution in the rock around the area of bit impact and, to a limited extent, the strain in the chisel-shaped bit itself. It was expected that a knowledge of the disposition of these strains, along with the rate of attenuation of strain energy in the rock

By George W. King

The yield strength of a dispersion-hardened W-3.8 vol pct Tho,alloy, in both the recovered and recrys-tallized condition, was investigated and cornpared with that ofrecrystallized pure tungsten over the temperature range of 325" to 2400°C. It is deduced that the Orowan mechanism is obeyed in the recrystallized alloy. In the recovered alloy, a further enhancement of the yield strength results from the retained substructure which is stable up to temperatures in excess of 2700°C. Temperature and strain rate cycling tests were also performed, and the apparent activation energy for the deformation process was derived. This activation energy, - 3 ev, for the recovered and also the recrystallized alloy was about the same as that for re crystallized pure tungsten. However, the activation volume of the recovered alloy, -10-2 cu cm, was about an order of magnitude lower than that of the recrystallized alloy or pure tungsten. This fact accounts for an enhancement oj- the temperature dependence of the yield stress of the recovered alloy. A dislocation velocity exponent of about 4 to 13 was deduced frorn the strain rate cycling tests , which is in good agreement with values reported for tungsten single crystals. VARIOUS theories have been developed to explain the enhanced yield strength of a metal containing a dispersed second phase of small hard particles. These theories are thoroughly reviewed by Kelly and Nicholson.&apos; The theoretical models can be separated into two types. The first type assumes direct interactions between moving dislocations and dispersoids. One of the most widely investigated models for this mechanism is the bowing out of dislocations between the dis-persoids and their subsequent pinching off in order to bypass the obstacles. This is the well-known Orowan mechanism.&apos; The second type is an indirect effect of the dispersion because of its ability to stabilize to high temperatures the substructure introduced by cold working. In this instance, the increment in the yield strength is expected to be inversely proportional to the square root of the subgrain diameter. In the present work, a quantitative study was made of the strengthening effect caused by a thoria dispersion in a recrystallized W-3.8 vol pct Thoz alloy over the temperature range 325" to 2400°C. The results are compared with the increment predicted for the Orowan mechanism based on the calculations by ~shb~.~ In addition, the alloy was tested in the recovered state so that any additional strengthening resulting from the substructure produced during fabrication could be measured. The respective contributions can be separated in this manner, provided that the particle size distribution of the dispersion remains the same in both the work-hardened and the recrystallized state. Particle size distribution measurements showed that this condition was met in the present work. I) EXPERIMENTAL PROCEDURES A) Material Production and Fabrication. The alloy investigated is essentially the same as that reported much earlier by ~effries,~ who also found the strength of tungsten to be improved by the thoria dispersion. The procedure for producing the alloy consisted of mechanically blending a thorium nitrate solution in proper concentration with tungsten oxide (WO3) powder, followed by hydrogen reduction to metal powder. After reduction, the dispersed second phase is present as thoria (Thoz). The pure tungsten powder used for comparison was produced in the same manner except that the thoria doping step was omitted. The powders were consolidated by cold pressing and self-resistance sintering in hydrogen. The resulting ingot had a cross section about 0.6 sq in. and a density about 93 pct of theoretical. The ingot was swaged to 0.174-in.-diam rod at temperatures varying from 1650°C initially to -1200°C near final rod sizes. Two intermediate recrystallization anneals were employed during fabrication. Analysis of the swaged rods is reported in Table I. B) Electron Microscopy Techniques. Carbon extraction rrPxcas prepared by a technique reported by ~00&apos; were used to quantitatively evaluate the thoria particle size and distribution. Electron nlicrographs of extraction replicas were taken at 20,000 times but were then enlarged two to three times in printing. The areas photographed were randomly selected. A Zeiss Particle Size Analyzer (Model TGZ3) was used to count and measure the sizes of all particles present on the print. About three thousand particles were counted in determining a distribution curve. Electron transmission microscopy was used to determine the effect of annealing on the substructures of the materials. Thin foils were produced by a two-stage thinning process. The rods were first ground on emery paper to ribbons about 10 mils thick and then a jet of 5 pct KOH was used to electrolytically reduce a portion of the cross section of the ribbon. Final perforation was achieved by immersing the specimen in a 5 pct KOH solution and electrolytically polishing at a current density of about 0.3 amp cm-&apos;. The foils were examined with a Hitachi HU-11A electron microscope. C) Tensile Testing. Tensile testing was performed in an Instron Testing Machine equipped with a radiation-type vacuum furnace which operates at about 1O"S torr at temperatures as high as 2400 °C. The same furnace was used for annealing the tensile specimens.

Jan 1, 1970

By T. O. King, Y. P. Gupta

The self-diffusion of sodium in two sodium silicate liquids was measured in the temperature range 850" to 1500°C by the capillary-reservoir technique. Radioactive Na 22 was used as the tracer. The total count and autoradiographic methods were used for determination of the total Na 22 depletion and diffusion profiles of the dqy-used specimens. The diffusion coefficients obtained by the autoradiographic technique are slightly smaller than those obtained by a total count method. Error analysis of the two methods suggests that more confidence be placed in the results of the total count method. The experimental results were analyzed in terms of the existing activated rate process theory. The activation energy for diffusion was shown to decrease markedly as the temperature increased. This was attributed to a variation in the heat of activation with temperature, probably related to a change in the distribution of anions associated wilh the cation. In terms of a model, suggested for diffusion in liquid silicates, differences in the aclivation energies for diffusion and electrical conduction may arise from the effect of the electric field applied in conduction measurements. It is generally accepted that liquid silicates consist of cations and an equilibrium distribution of complex anions determined by temperature and composition. Transport properties in molten silicates are of interest, not merely because of their relevance to the kinetics of pyrometallurgical reactions and glassmak-ing processes, but also because they are useful to development of the theory of such ionic liquids. Self-diffusion is one such transport process that may, if studied for liquid silicates of widely varying compositions, indicate structural changes through changes in the activation energy for diffusion. The self-diffusion of calcium, silicon,&apos; sulfur: aluminum, 4 and oxygenS in lime-alumina-silica melts and of iron6 in molten iron silicates have been measured. Unfortunately, the errors in some of the reported activation energies for diffusion are too large to allow firm conclusions concerning structure and the mechanism of the diffusion process to be drawn. The research reported here was a study of the self-diffusion of sodium in liquid sodium silicates. The soda-silica system was chosen since: i) a reasonable composition range can be covered in the binary system at moderate temperatures; ii) suitable isotopes of sodium (radioactive Na 22 and NaZ4) can be obtained; iii) data on the electrical conductivity and viscosity of sodium silicate liquids are available. However, the range of composition actually used in diffusion experiments was limited, to 20 to 35 wt pct soda, by the relatively high viscosity of silica-rich compositions and by evaporation of soda from basic melts. EXPERIMENTAL PROCEDURE The capillary-reservoir technique was used, wherein a radioactive tracer, Na 22, incorporated in the capillary melt, was allowed to diffuse out of the platinum capillary tube into a large reservoir of silicate liquid containing a chemically identical melt, but without radioactive tracer. After a specific diffusion time, both the total depletion in the tracer concentration and concentration-distance profiles of the diffused samples were measured by procedures to be described later. The diffusion cell assembly was similar to that used by Koros and King.&apos; The temperature of the diffusion cell was measured with a calibrated Pt, Pt-10 pct Rh thermocouple located at the center of the liquid reservoir. The same thermocouple was used to obtain the temperature profile in the reservoir. The temperature at the top of the reservoir was slightly higher (2°C) than that at the bottom, to minimize convection in the capillary tubes, which were placed, open end up, in the reservoir. Convection was not expected to be a problem since the length-to-diameter ratio of the tubes was about 12:1 and the maximum capillary diameter was 1 mm. The diffusion cell was heated in a molybdenum-wire resistance furnace, previously used by Koros and King, but somewhat modified. A Pt, Pt-10 pct Rh thermocouple enclosed in an alumina tube and located near the furnace winding was used in conjunction with a preamplifier and Micromax proportional controller for temperature control, within 4°C, at temperatures near 1500°C. Before starting a diffusion run, the furnace was heated to the desired temperature and an alumina guide assembly for the capillaries was slowly lowered to within 2 cm of the liquid reservoir. The capillaries were thus heated to about the temperature of the bath. The run was started by lowering the assembly till the open ends of the capillaries were about 1 cm below the surface of the liquid. The run was ended by raising the assembly to about 15 cm above the liquid bath. Later, the sample assembly was slowly withdrawn from the furnace. Six diffusion samples were usually run at the same time. Three runs made with the open ends of the capillaries down were discarded because in the majority of these samples air bubbles trapped at the open end were observed. Some glass adhered to the outside of the capillary on withdrawal. This was carefully removed and used to check that the Na 22 activity in the sink remained at a low level. Materials. Nonradioactive sodium silicates were prepared by melting, in a platinum crucible, weighed quantities of sodium carbonate and powdered silica. To prepare radioactive sodium silicates, Na2 obtained in HC1 solution, was first checked for radioactive impurities by obtaining a y-ray energy spectrum, then the chloride ions were removed by anion-ex-

Jan 1, 1968

By J. R. Low, D. F. Stein

Single crystals of iron have been grown from three different lots of Ferrovac "E" of somewhat different chemical composition by the strain anneal technique. Using a technique to seed the crystal similar to Dunn&apos;s for silicon-iron, it has been possible to orient the crystals grown in both direction and plane of growth. Crystals having the plane of the strip oriented (100) , (110), (111), (112), (123), and (491) have been grown. The growth directions used have been [100], [110], 45 deg from a [110}, and various others of no specific crystal orientation. The usual dimensions of the crystals were 8 by 1 by 0.08 in. Attempts to grow crystals were about 90 pct successful. METHODS of growing single crystals of high purity iron have been reported in the literature.1-4 However, each of these methods was not completely reliable when used on materials having slightly different chemical composition and in some instances a small number of successes were obtained using identical materials. Except for the method used by S. Dohi and T. Yamoshita,1 it has not been possible to reorient single crystals of high purity iron to give any desired orientation. The method to be described has made it possible to grow single crystals from three different lots of material having different compositions, and to orient the crystals with respect to growth direction and surface. STARTING MATERIAL The material used during this investigation was a vacuum melted high purity iron marketed by the Vacuum Metals Corporation designated Ferrovac "E." Three lots of Ferrovac "E" having the following composition were used with equal success: The compositions listed are those of the as-received material; and they may have been modified before the growth of single crystals. Analysis of heat B just before growth and after growth revealed that the heat treatment prior to growth did not change the carbon content, but the oxygen content was changed from 0.0092 pct to 0.0034 pct and the nitrogen content from 0.0003 pct to 0.0001 pct. After growth of the single crystals, the carbon had dropped to 0.001 pct. None of the heat treatments would be expected to change any of the other impurities very markedly. Heat C would be expected to have a metallic impurity content similar to heats A and B. PROCEDURE Ferrovac "E" iron which had been obtained in bar form having a diameter of about 1 in. was rolled into strip for growing single crystals. By passing the 1-in. bar through a cold rolling mill several times, it was reduced to a strip 0.15 in. thick. The strips obtained were then cut into suitable lengths for heat treating (about 9 in. long), annealed at 925°C for 2 hr in dry hydrogen and water quenched. It was then necessary to bake the strip at 200°C for 24 hr in air in order to prevent cracking during further rolling operations. While it was possible to cold roll the 1-in. bar directly to the desired 0.080-in. strip, the intermediate anneal was used because the strip so obtained produced better single crystals. The strip obtained by rolling the 1 -in. bar directly to 0.080-in. strip produced single crystals having a large number of occluded grains. Experiments showed that the optimum reduction in area by rolling prior to the growth of single crystals was about 50 pct. Attempts to grow single crystals from material that had been reduced less than 40 pct were unsuccessful presumably because the matrix did not possess the critical amount of texture necessary for growth. The strip obtained after the rolling operations had very irregular edges which were ground to give a strip with uniform dimensions. The strip was then annealed at 825°C for 3 hr in hydrogen and furnace cooled. Fig. 1 illustrates the grain size obtained. A temperature of 940°C was used for the annealing temperature on one group of strips

Jan 1, 1962

By Sherwin F. Kelly

THE principal interest in the meeting sings arranged by the Geophysical Committee this year centered around the many papers dealing with the practical applications of geophysical methods to solving geological problems in many other parts of the world. The program Wednesday morning dealt with work in South Africa, Poland, and South America. Rudolph Krahmann&apos;s first paper gave a perspective of the geophysical investigations upon mineral deposits in South Africa. A striking point in his story was the tremendous increase in magnetic work during the last two or three years. This is largely accounted for by the intensive exploration for the extension of the Witwatersrand gold mining area. The author mentioned many surveys in which other methods were used for the search for ores of copper, lead, and zinc, and in the study of water-bearing and oil-bearing structures.

Jan 1, 1935

By Robert Peele

TWO outstanding members of the Institute will be honored at the Annual Meeting this month: Robert Peele, who will accept his election to the small group of Honorary Members; and Clinton Hoadley Crane, president of the St. Joseph Lead Co. and William Lawrence Saunders Medalist for 1936. Eminence in the profession character, interest in Institute activities, and general recognition as a gentleman and a friend by so many people, have contributed to the election of Professor Peele. The Saunders Medal is for "achievement in mining." In awarding it to Mr. Crane the citation reads "For distinguished achievement in the successful development and operation of low-grade lead mines."

Jan 1, 1936

By A. W. Jenike

A theory of gravity flow of bulk solids like ores, concentrates, coal is outlined and an example of design for unobstructed flow is given. Mass-flow and plug-flow patterns are defined and related to the geometry of the bin. The effect of these patterns on segregation, first in-first out flow, and caking is described. This paper is a report on the results from the AIME sponsored project "Flow of Bulk Solids" which was carried out under the author&apos;s direction at the Utah Engineering Experiment Station, University of Utah, during the period 1956-1962. The theory has been applied to the design of numerous industrial storage plants. A QUANTITATIVE METHOD OF DESIGN FOR FLOW There is hardly an industry which does not store and handle solid materials in bulk form. When the volume of the solids is large, gravity is invariably relied upon to cause the solids to flow out of storage, through channels and chemical reactors. Such materials as ore, coal, cement, flour, plastics, clay, soil, to which a general term of bulk solids is applied, flow by gravity or are expected to flow by gravity in thousands of installations and by billions of tons annually. The chemical and process industry depends on gravity flow of solids in process and out of storage. Mining relies on gravity flow in block-caving, in ore passes, as well as in storage and loading bins. Agriculture uses gravity flow in elevators, in feed plants, and in farm silos. In practice, satisfactory gravity flow is seldom attained. Such problems as doming, piping (rat-holing), lack of live capacity, segregation, deterioration in storage, harass industry. In spite of the universality of these problems, until recently, there has been no theory of solids flow, no method of predicting how a solid would behave, and how the channel, bin, or hopper should be designed. In the late nineteen forties and early fifties, the theory of plasticity came of age and simultaneously the computer became widely available. These two factors permitted the development of a theory of flow of bulk solids. The work was conducted during the years 1953-1961. In conjunction with the development of the theory a method to measure the flowability of solids was also developed1-7 and the theory was ap-plied to the design of ore pockets, storage plants,16 chemical reactors and adsorption columns. A comprehensive report of this work is given in a previous work." THEORY OF FLOW The most important question which a theory of flow has to answer is: what conditions need to be satisfied for a given solid to flow uniformly and without obstructions through a channel? First of all, the following observations are made:

Jan 1, 1967

By Ferid Kromer

Geography: The Tagtepe district of the Vilayet of Eskigehir is about 20 miles northeast of the city of Eskigehir (approximately midway between Ankara and Istanbul) in western Anatolia. The area is a mountainous one, the highest peak being Tagtepe Mountain (5200 ft) which is approximately in the center of the district. The mountains drop off to the deep valley of the Sakarya River on the north and to the plain of Eskigehir on the south. FERID KROMER, Junior Member AZME, is a Consulting Mining Engineer and General Manager, Bagtag Turk Maadin Ltd., Istanbul, Turkey. New York Meeting, February 1950. TP 2629 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Dec. 29, 1948. For the most part, the watershed is on the northern side of the mountain barrier, draining into the Sakarya River, which in turn empties into the Black Sea midway between Zonguldak and the mouth of the Bosphorus. The approximate area covered by the Tagtepe district is shown in fig. 1. Transportation to shipping points is available via the Istanbul-Ankara railroad. The station on this line nearest the mining district is Alpikoy station, about 20 miles by road southwest of Tagtepe Mountain. Interior roads within the district are poor. Being of dirt, the winter rains and snows render them almost impassable for trucks from about the middle of December until the end of March, thus presenting a considerable transportation problem. However, the roads from the Bagoren and Tagtepe chromite mines to the railroad shipping point at Alpikoy station have recently been repaired and will be maintained for all-weather truck transportation. Detailed climatic data are not available. However, in general the spring, summer, and early autumn months are dry, and good weather may be expected from May until early November. Then the winter rains commence, and heavy snow is usual during January and February. Geology: The mountainous structure of Tagtepe belongs to basic rocks of serpentine (Variscan Orogeny) which is in contact with Paleozoic schists at west, and an Oligocene outcrop of red clays in Margi-Sepetci region (see fig. 1) at southeast. The northwest and southwest borders of Tagtepe district are, respectively, surrounded by Paleozoic schists and pebbly gray and yellow Neogene clays. More recent formations of alluviums overlay the plain of Eskigehir. Dark basic rocks of trachytes with hornblende are visible on Turkmenbaba Mountain, at the west of Tagtepe. Mineral Occurrences: Chromite: the most important mineral found in any quantity in the Tagtepe district. The alignment of the deposits of chromite is in general along the line Bagoren-Tagtepe (see fig. 1). The first mines in the area were those of Tagtepe and Bagoren, which were developed over 20 years ago with Swedish capital. Other deposits of chromite, more recently discovered and so far of less importance, are being worked at Kurucor, Komurcu, Gelinmezari, and Lacin (see fig. 1). Deposits average generally between 46 and 48 pct chromic oxide, with the exception of the Bagoren mine which averages 44 pct. However, a new lode, very recently plotted, in the Tagtepe mine averages 50 pct Cr,O,, 4.6 pct SOz, and 7 pct FeO. Geological character of the chromite occurrences in the Tagtepe mine may be considered typical of most chromite lodes in this area. The indications are that the formations of ore lenses are developed by the segregation of chromite crystals intruded into the serpentinized rock, and exposed later to tectonic movement within the zone of crystallization. All lenticular masses are more or less regular in shape and follow each other in southeast-northwest direction and dip generally 70" NE. Ore lenses do not seem to persist in depth, average depth of two lenses is 60 ft below surface. Three lodes .have been mined as open-pit. The average dimensions of individual lenses are as follows: pitch length, 100 ft; breadth, 27 ft; and width, 20 ft. The lenses and their enclosing rocks are broken by parallel fractures in approximately east-west direction. These joints are filled, except in one lode, with cementing material, which gives to the ore a

Jan 1, 1951

By Harold M. Mooney

WHEN apparent resistivity data are taken with the symmetrical Wenner 4-electrode spread, a fixed center position is used and readings are taken for values of electrode separation. Basic data consist of apparent resistivity plotted against separation of adjacent electrodes . The interpreter attempts to infer geologic structure, such as the depth to discontinuities and the nature of subsurface earth materials. An earlier paper&apos; described methods for interpreting resistivity data. All of these involve a severe assumption, namely that the earth in the region of interest consists of horizontal layers, electrically homogeneous and isotropic. The actual earth never satisfies this assumption exactly and may deviate from it so much that none of the above methods can be applied. Attempts in three directions have been made to modify the assumption so that it approaches known geologic complexity more closely. First, curves have been calculated for dipping discontinuities. Stern&apos; and Aldredge hose a few widely separated dip angles. Trudu confined his attention to small dips. Berel&apos;kovskiy and Zubanov computed gradient curves for widely separated dip angles. Unz as given the most complete solution, with a brief attempt to treat the three-layer case. Second, anisotropy can be taken into account. It seems geologically probable that layered materials have different vertical and horizontal conductivities. Cagniard, Maillet, and Pirson et up methods for finding an equivalent hypothetical isotropic medium. Standard interpretation methods can be applied to this, and the actual medium can then be deduced. Belluigi&apos;" discounts the practical importance of anisotropy; Geneslay and Rouget do not agree with his conclusion. Third, the effect of variable resistivity in a layer can be considered. Keck and Colby" examine the mathematics of an exponential increase in a surface layer. Several authors, for example, Stevenson,&apos;&apos; consider a continuous variation of resistivity with depth. The present paper deals with a linear variation of resistivity in a surface layer. Geologically, surface variations should be expected. Unconsolidated materials such as glacial drift show marked irregularities over short distances. The effects of weathering change with depth. The moisture content of material above the water table may vary from a dry sand to a saturated clay, and both of these will be changed by rainfall. Figs. 1 to 6 present apparent resistivity curves to show the effect of a variable surface layer. In all cases resistivity varies linearly with depth down to a depth of one unit. Material beneath this depth has constant resistivity. Electrode separation is plotted in depth units. Insets on each figure show the corresponding cross-sections, plotting true resistivity against depth. To illustrate, consider curve A of Fig. 1. The true resistivity of material at the surface of the earth is taken as 0.4 units. Resistivity increases with depth, reaching a value of 1.0 at 0.5 depth units and 1.6 at 1.0 depth units. Below a depth of 1.0, all the material has very low resistivity (zero, for purposes of calculation). Curve A in the main part of Fig. 1 shows how apparent resistivity varies for this case as the electrode spacing is increased. To illustrate further, curve E of Fig. 4 corresponds to true resistivity of 1.2 units at the surface, 1.0 at a depth of 0.5 units, 0.8 at a depth of 1.0, and 1.5 for all depths greater than 1.0. Apparent resistivity curves have been plotted logarithmically so that the shape of the curves becomes independent of the units, giving the curves wide validity. A certain drift-covered area, for example, shows a gradual decrease of resistivity from 230 ohm-meters at the surface to 150 ohm-meters at the bedrock surface, 275 ft down; bedrock resistivity is 800 ohm-meters. Curve E of Fig. 5 indicates that true resistivity decreases from 1.2 units at the surface to 0.8 at a depth of 1.0, then increases abruptly to a constant value of 4.0 units. Since resistivity and depth ratios are the same, this can be used to predict the field curve. For Fig. 5, multiply true resistivity and apparent resistivity by

Jan 1, 1955

By Ferid Kromer

Geography: The Tagtepe district of the Vilayet of Eskigehir is about 20 miles northeast of the city of Eskigehir (approximately midway between Ankara and Istanbul) in western Anatolia. The area is a mountainous one, the highest peak being Tagtepe Mountain (5200 ft) which is approximately in the center of the district. The mountains drop off to the deep valley of the Sakarya River on the north and to the plain of Eskigehir on the south. FERID KROMER, Junior Member AZME, is a Consulting Mining Engineer and General Manager, Bagtag Turk Maadin Ltd., Istanbul, Turkey. New York Meeting, February 1950. TP 2629 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Dec. 29, 1948. For the most part, the watershed is on the northern side of the mountain barrier, draining into the Sakarya River, which in turn empties into the Black Sea midway between Zonguldak and the mouth of the Bosphorus. The approximate area covered by the Tagtepe district is shown in fig. 1. Transportation to shipping points is available via the Istanbul-Ankara railroad. The station on this line nearest the mining district is Alpikoy station, about 20 miles by road southwest of Tagtepe Mountain. Interior roads within the district are poor. Being of dirt, the winter rains and snows render them almost impassable for trucks from about the middle of December until the end of March, thus presenting a considerable transportation problem. However, the roads from the Bagoren and Tagtepe chromite mines to the railroad shipping point at Alpikoy station have recently been repaired and will be maintained for all-weather truck transportation. Detailed climatic data are not available. However, in general the spring, summer, and early autumn months are dry, and good weather may be expected from May until early November. Then the winter rains commence, and heavy snow is usual during January and February. Geology: The mountainous structure of Tagtepe belongs to basic rocks of serpentine (Variscan Orogeny) which is in contact with Paleozoic schists at west, and an Oligocene outcrop of red clays in Margi-Sepetci region (see fig. 1) at southeast. The northwest and southwest borders of Tagtepe district are, respectively, surrounded by Paleozoic schists and pebbly gray and yellow Neogene clays. More recent formations of alluviums overlay the plain of Eskigehir. Dark basic rocks of trachytes with hornblende are visible on Turkmenbaba Mountain, at the west of Tagtepe. Mineral Occurrences: Chromite: the most important mineral found in any quantity in the Tagtepe district. The alignment of the deposits of chromite is in general along the line Bagoren-Tagtepe (see fig. 1). The first mines in the area were those of Tagtepe and Bagoren, which were developed over 20 years ago with Swedish capital. Other deposits of chromite, more recently discovered and so far of less importance, are being worked at Kurucor, Komurcu, Gelinmezari, and Lacin (see fig. 1). Deposits average generally between 46 and 48 pct chromic oxide, with the exception of the Bagoren mine which averages 44 pct. However, a new lode, very recently plotted, in the Tagtepe mine averages 50 pct Cr,O,, 4.6 pct SOz, and 7 pct FeO. Geological character of the chromite occurrences in the Tagtepe mine may be considered typical of most chromite lodes in this area. The indications are that the formations of ore lenses are developed by the segregation of chromite crystals intruded into the serpentinized rock, and exposed later to tectonic movement within the zone of crystallization. All lenticular masses are more or less regular in shape and follow each other in southeast-northwest direction and dip generally 70" NE. Ore lenses do not seem to persist in depth, average depth of two lenses is 60 ft below surface. Three lodes .have been mined as open-pit. The average dimensions of individual lenses are as follows: pitch length, 100 ft; breadth, 27 ft; and width, 20 ft. The lenses and their enclosing rocks are broken by parallel fractures in approximately east-west direction. These joints are filled, except in one lode, with cementing material, which gives to the ore a

Jan 1, 1951

By J. E. Papin

MORENCI ores contain as an average about 0.015 pct molybdenite, MoS2. Incidental to the concentrating operations applied for the recovery of copper minerals, approximately two-thirds of the molybdenite is floated and appears in the final copper concentrate. The economic importance of molybdenum and the success achieved in its recovery in milling operations elsewhere encouraged research directed toward its recovery in marketable form. Several procedures are utilized to effect separation of molybdenite from copper and iron sulphides, but only two have wide application. In the better known of these two methods the molybdenite in the copper concentrate is depressed in a flotation operation using soluble starch as the depressant. The tailing from this treatment thus becomes a low-grade molybdenite concentrate which after thickening, filtering, and low temperature roasting is repulped with water and subjected to additional flotation steps for recovery of the molybdenite. A thio-phos-phate collecting agent is employed in flotation of the copper minerals. Presumably the stability and lasting effects of that collector type necessitated the practice of depressing molybdenite followed by subsequent roasting to insure elimination of copper and iron sulphides from final molybdenite concentrate. The second important method of recovery is applied at various southwestern plants. In those plants xanthates are in use as copper collecting agents. It has been found that xanthates are relatively unstable and their collecting power for sulphides is destroyed by very simple procedures. The method generally applied is to subject the xanthate-acti-vated concentrate, in the form of a pulp, to prolonged heating using steam as the heating medium. A concentrate thus treated may then be subjected to a flotation operation for recovery of the molybdenite, using mineral oil collecting agents, and the copper and iron sulphides will be depressed. Neither of the above processes was applicable to Morenci concentrates. Morenci uses a thio-phos-phate collecting agent in its flotation operation. However, it was established that soluble starch was not a depressant for Morenci molybdenite; therefore the first step in that process was not applicable. AS would be expected the copper and iron sulphides in Morenci concentrates could not be depressed by the heating methods used on xanthate activated concentrates. Low-temperature roasting did eliminate the effects of the thio-phosphate but had to be rejected as uneconomic in as much as the tonnage of concentrates involved was too great. Preliminary research having established the above facts, it became obvious that new methods would have to be developed for the recovery of molybdenite from Morenci concentrates. A broad laboratory investigation was initiated along two general lines, both directed toward depression of copper and iron sulphides. One approach was through the use of water-soluble oxidizing agents with the objective of destroying the thio-phosphate in the concentrate and thus eliminating its collector effect. The other approach involved the use of soluble sulphides, which have long been recognized as sulphide depressants. These efforts resulted in laboratory processes which showed promise. Research was then extended to a pilot plant having a daily capacity of several tons of concentrate. This operation soon demonstrated that soluble sulphide—basically sodium polysulphide—when applied to a pulp made slightly acid with sulphuric acid, proved to be the most effective sulphide depressant. The rate of concentrate treatment in this plant and the low molybdenite content of the concentrate prevented carrying the process to a conclusion, namely, production of molybdenite concentrate of marketable grade. Laboratory treatment of pilot plant concentrate indicated that a marketable product could be made from it, given a tonnage suited to available cleaner flotation machine capacity. Accordingly, the molybdenite plant was enlarged to permit treatment of the total copper concentrate from the extension plant, maximum of approximately 800 tons per day. In the enlarged plant a major difficulty was encountered. No criteria could be established as a basis for control of the process. In the early stages of flotation, because of the small amount of molybdenite involved, there was no visual evidence of the relative floatability of molybdenite with respect to

Jan 1, 1956

By E. A. Steigerwald

E. A. Steigerwald (Thompson Ramo Wooldridge, Inc.1— he authors&apos; results clearly indicate that cracking can be produced by the hydrogen pressure developed during a charging operation. This type of cracking or blistering has also been observed in polycrystalline materials24"28 when the charging conditions are sufficiently severe and is often referred to as irreversible embrittlement since it cannot be removed by a baking treatment. There are additional data, however, which must be considered before a pressure theory can be generally employed to account for all failures which occur as a result of hydrogen. In many cases, hydrogen embrittlement in a tensile test or in delayed failures under static loads is a reversible phenomena which cannot be simply explained on the basis of preexisting cracks generated by the charging operation. It is this aspect of the problem which has prompted many investigators to seek mechanisms other than hydrogen pressure to explain their results.24&apos;n728 Fig. 15 indicates an example where, under specific experimental circumstances, hydrogen embrittlement can occur at liquid nitrogen temperatures. In this case, which has been previously decribed,&apos;&apos; specimens were charged with varying quantities of hydrogen, immediately quenched, and tested in liquid nitrogen (-320°F). A companion set of identical specimens were charged, aged at 300°F to remove the hydrogen, and also tested at -320°F. When the current density was greater than lo-&apos; amp per sq in., embrittlekent occurred in both sets of specimens, indicating that cracking had occurred during charging and the embrittlement, as in the case of Fe-Si single crystals, was irreversible. At current densities between approximately 103 and lo-&apos; amp per sq in, the embrittlement was present only for those specimens which contained hydrogen during the testing sequence. The embrittlement was therefore reversible with respect to the aging and charging operations. Since extensive hydrogen movement would not be expected at -320°F, it is difficult to reconcile these data with a mechanism which requires pressure and pressure dependent growth of preexisting cracks. There are other features of hydrogen embrittlement such as the reversibility of the incubation time for delayed failure with respect to applied stressg0 and the influence of prestraining31 which are also difficult to explain using a pressure model. Any general mechanism of hydrogen embrittlement will have to consider the reversible aspects of the embrittlement data as well as the irreversible portion which has been clearly presented for the Fe-Si crystals and which is consistent with a pressure model. A. S. Tetelman and W. D. Robertson (authors&apos; reply)—he authors agree with Dr. Steigerwald that a general mechanism of hydrogen embrittlement must be applicable in all cases where embrittlement occurs. Dr. Steigerwald&apos;s experiments were performed on an iron alloy which has an extremely complex microstructure, and therefore does not lend itself to the direct and detailed observations that can be made in Fe-Si. The change in the characteristics of cracks as a consequence of annealing at 300°F is not really known in detail but it is probable that stress-relaxation (blunting) occurs, dislocations produced near the crack tips will be pinned by carbon atoms, and hydrogen will be lost to the atmosphere. Any, or all of these effects of annealing will alter the ease with which a crack subsequently propagates under applied stress. A quantitative treatment of the problem must take these effects into account. Since diffusional processes are presumably eliminated at -320°F, the general mechanism proposed by Dr. Steigerwald&apos;s colleagues cannot be operative at this temperature. A detailed discussion of the general&apos; inapplicability of this mechanism has been presented elsewhere. However, the data presented by Dr. Steigerwald in his discussion can be explained in terms of a pressure model. Crack propagation under internal pressure P and applied stress occurs when where is the total energy expended in creating new surface area and by plastic work at the crack tip. The total crack length increases with increasing current density, since we have shown that it systematically increases with hydrogen concentration and Dr. Steigerwald has shown that hydrogen concentration increases with current density. For large L (high current density) Eq. [I] can be satisfied even if P = 0 and the embrittlement process does not require the presence of hydrogen. Specimens charged at a lower current density will con-

Jan 1, 1963

By J. W. Spretnak, V. Kandarpa

Stress -induced ordering of carbon atoms is studied in a series of Fe-Mn-C alloys. A prominent peak is found in the vicinity of 280°C at frequencies of the order of 1.0 cps, with an associated activation energy of 37 kcal per mole. The height of the peak is linearly rekzted to the concentration of carbon in solution. The distortion of octahedral holes by manganese atoms appears to be predominant over carbon-carbon pair interactions. RELAXATION by stress-induced ordering of point defects is expected whenever the introduction of these point defects produces distortions which have a lower symmetry than that of the lattice. Under zero stress, the isolated point defects occupy the crystallographic-ally equivalent positions in the lattice, as these represent states of equal energy. However, if the defect sites are asymmetric, application of an uniaxial stress will split the energy states, and a redistribution of the defects among various states will take place. This is the case of the internal friction peak called the Snoek peak,1 resulting from isolated interstitials in bcc metals. The interstitial sites in this case have tetragonal symmetry. In the case of fcc and hcp lattices, such an effect is not expected from isolated point defects because of the symmetrical nature of the interstitial sites. However, internal friction peaks arising from interstitial diffusion have been reported both in hcp2,3 and fcc4-8 lattices. These peaks are often explained on the basis of stress-induced ordering of interstitial solutes, caused by the deviation of interstitial sites from their cubic symmetry through the presence of nearby defects. In the case of fcc lattices, evidence for interactions of both the substitutional-interstitial4,6,13 and interstitial-interstitial types5&apos;798&apos;14 have been presented by various investigators. The purpose of the present investigation was to study the internal friction peak attributed to the diffusion of interstitial carbon atoms in high purity austenitic manganese steels and to account for the peak in the light of the existing models. MATERIALS The Fe-Mn-C alloys used in the present investigation were made in two different ways, designated as Type I and Type 11. Type I alloys were made from high purity Fe-Mn alloys obtained in the form of 0.04- in.-diam wires from Materials Research Corporation, Orangeburg, N.Y. These alloys were carburized to different levels using gas mixtures of H2 and CH4 at 1000°C. Type I1 alloys were made in this laboratory starting with zone refined iron, spectrographically pure manganese, and spectrographically pure carbon. They were melted in an argon arc melting furnace and drawn into 0.04-in.-diam wires. All the wires were annealed at about 900°C for 3 hr prior to the internal friction experiments. After the measurements of internal friction, the phases in the samples were identified by X-ray diffraction and the carbon determined by the combustion method. EXPERIMENTAL PROCEDURE In the present work, a classical Ke-type pendulum was used. The details of the equipment were described previously by D. T. Peters.9 Dry helium at 40 torr was used in all the experiments. The internal friction, measured as the logarithmic decrement of the torsion amplitude of vibration was determined as a function of temperature, from ambient to about 500°C. The background internal friction was assumed to have the form of the exponential of the inverse temperature and was subtracted from the raw data. The height of the peak was measured at the position of the maximum in the plot of the internal friction versus temperature. The activation energies of the peaks were measured by the peak shift method. The internal friction values for an alloy were obtained as a function of temperature at different frequencies of vibration. The position of the peak changes with frequency, the higher the frequency the higher the peak temperature. The activation energy of the process associated with the peak is obtained using the formula

Jan 1, 1970