Search Documents

By H. Furman Byars

INTRODUCTION of bottom dump hauling units into the Ray, Ariz., stripping operation of the Isbell Construction Co., was motivated by several reasons, with what appears to be debatable results. The accepted theory of truck design for use in open-pit holds that end dump vehicles are the most adaptable for the work. But, because operations of the bottom dump, under certain construction and haulage conditions, proved economically feasible, the unit was put to work in the Ray copper pit. The decision to try bottom dump was reached after considerable observation of the unit in action on construction of earth filled dams, levees, airport construction and several other similar tasks. Basic tire design also motivated the choice. All things being equal, a vehicle running on low pressure single tires will outperform another operating on dual high pressure tires, providing load carrying capacities are the same. The investment required to equip a vehicle with four single tires to handle the same load as one with dual tires mounted on two axles and single front axles is about 60 pct greater. Thus, in order to reach the break even point on tire costs, single tires must operate 60 pct longer. Comparison is made with a truck outfitted with 10 16:00x25 tires. Two other factors were considered in selecting bottom dump trucks. It was felt the bottom dump principle would work well in dumping ore into a hopper where gate design fits this particular method. Also, with the absence of hydraulic dumping, ore pollution with oil is reduced. The mechanical simplicity of the unit also lent weight to its choice. Ordinary reasoning indicated maintenance costs would be low compared with other units carrying similar loads. The bottom dumping principle is not new. It dates back to the days when horses were used to haul the same kind of rig. The unit employed at Ray holds 25 cu yd struck measure, or approximately 42 short tons. Dumping is accomplished by releasing an air cylinder opening a dog holding the doors. Doors are closed by a cable system operating off a wheel wind deriving power by friction with the trailer tire. The unit is mounted on four 27.00x33 and two 14.00x24 tires on the front axle. The power unit is a 300 hp Cummins engine. Hydraulic power boosts the steering. A straight mechanical drive and friction clutch with 10 speeds is used. Conditions Not Ideal Top performance of the truck can be expected only under the conditions for which it was designed, in particular grades under 5 pct, handling fine material, and dumping where one thin layer can be placed on top of another. The machine will handle 42 tons per haul, operating at high speed, with only seconds used for dumping. On a 2 or 3 pct grade over a one mile haul,

Jan 1, 1952

WE vote this month without knowledge of either major presidential candidates' position on mineral problems. Too long have we kept our own counsel, turned our backs on the public. Certainly we must formulate policies upon which we may unite in industry council, but implementation of these by legislative bodies requires popular understanding, if not support. The earth and its resources are the province of the miner and the farmer but beyond this, and the basic need of the economy for both, the similarity ends. In this election year the disparity between the poll strength of these two fundamental callings is apparent. While both candidates have found it essential to incorporate a farm plank in their platforms, mining has been neglected as not being a basic issue. If this gives the mining fraternity the advantage of voting objectively, it also leaves the general public in the dark as to the attitude of the candidate on a basic issue. It is an issue on which depends the future of the nation, but, unfortunately, the public is not aware of its own vital stake in mining. Thus election time brings with it a fresh example of the evils of automatic lawn sprinkling-a long standing peeve of ours. Back in the days of the hand-held sprinkling hose in the intimacy of the twilight the mining man had the opportunity to unburden himself on the problems of mining to his neighbor who might be a doctor, lawyer, or accountant. With the encroachment of mechanized sprinkling, yet another forum for the indoctrination of the layman into the significance of mining has disappeared. Familiarizing your neighbors with mining in the lawn sprinkling societies of yesteryear was the individual's contribution to public relations for mining. The corporations can use educational advertising in popular magazines as is practiced by such companies as Kennecott. The AIME can play an important part by providing career guidance information on the mineral industries. We offer the suggestion to the American Min¬ing Congress, that the splendid exhibitions of mining machinery featured in alternate years for metal and coal mining, respectively, might be opened to the general public one night during the week of the show. Newspaper publicity would add greatly to the public's interest in such an opportunity. Power for the public is considered a vote-getter and no candidate has neglected to make his stand on this subject. Is the price of the kilowatt in the home of greater importance to the voter than the price of the metal durable goods which he purchases every year? Not really, but the voter thinks so. Mining has as much sales appeal as 'potatoes or kilowatts if presented in the proper way. We suggest that a little hand lawn sprinkling by the right people in the right places would produce an abundance of publicity which would give Mr. and Mrs. American something new to expect from their representatives-a vigilance over the flowering of their mining industry.

Jan 1, 1952

By Edward Wisser

The environment of an ore body is taken to mean not only its physical surroundings but every factor, passive or active, that conditioned the ore shoot, saving only the original composition of the solutions that formed the shoot. Collection of data related to the shape and characteristics of veins should be followed by correlation of the data and the formulation of generalizations regarding ore formation. The nature of the criteria used in arriving at these generalizations is discussed. Certain of the criteria, when used with an understanding of their underlying causes, become "ore-guides." In the course of his study the geologist must not confine himself to the immediate surroundings of the veins, but should attempt to work out the geologic history of events culminating in the crucial epoch for any mining district, the period of mineralization. The work may involve study of features far removed from the veins and related to them only indirectly. It commonly means thorough study of the geology of the entire region surrounding the ore deposits. The following question has been suggested for discussion: "Are there any criteria by which one can determine when mining operations have reached the roots of an ore deposit?" The question deals less with the roots of a particular ore body than with the lower limit of the vertical range within which ore bodies may be expected. It concerns a critical line upon the longitudinal vertical projection of a vein.† Below this line it is useless to look for ore shoots; above the line exploration below the bottoms of individual ore shoots may be justified. Can we learn to determine the position of such a line? In some multivein districts the line for any given vein may be approximated by simple interpolation or extrapolation. Where this is possiblc the bottoms of the lowest ore shoots in the various veins are points on an imaginary, gently rolling surface. The trace of this surface upon the vein is our critical line for that vein. The imaginary surface rolls so gently that it may be projected from two or more known veins to an unexplored vein near by. Here is a criterion for the bottoming of ore that has nothing to do with changes in the appearance of the vein in question; it rests solely on the depth at which the ore bottomed in adjacent veins. The method is not applicable in districts only slightly explored in depth, nor where the lower limit of the ore-bearing horizons

Jan 1, 1941

By T. R. Graham, R. S. Dean. J. R. Long

Although considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to II pet aluminum, with some incidental information on the single-phase alpha solid solution alloys. Straussl gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper6 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50" temperature levels from 400' to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solub%ty of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 13oo'F and higher,

Jan 1, 1947

By R. S. Dean. J. R. Long, T. R. Graham

Although considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to II pet aluminum, with some incidental information on the single-phase alpha solid solution alloys. Straussl gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper6 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50" temperature levels from 400' to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solub%ty of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 13oo'F and higher,

Jan 1, 1947

By Edward Wisser

The environment of an ore body is taken to mean not only its physical surroundings but every factor, passive or active, that conditioned the ore shoot, saving only the original composition of the solutions that formed the shoot. Collection of data related to the shape and characteristics of veins should be followed by correlation of the data and the formulation of generalizations regarding ore formation. The nature of the criteria used in arriving at these generalizations is discussed. Certain of the criteria, when used with an understanding of their underlying causes, become "ore-guides." In the course of his study the geologist must not confine himself to the immediate surroundings of the veins, but should attempt to work out the geologic history of events culminating in the crucial epoch for any mining district, the period of mineralization. The work may involve study of features far removed from the veins and related to them only indirectly. It commonly means thorough study of the geology of the entire region surrounding the ore deposits. The following question has been suggested for discussion: "Are there any criteria by which one can determine when mining operations have reached the roots of an ore deposit?" The question deals less with the roots of a particular ore body than with the lower limit of the vertical range within which ore bodies may be expected. It concerns a critical line upon the longitudinal vertical projection of a vein.† Below this line it is useless to look for ore shoots; above the line exploration below the bottoms of individual ore shoots may be justified. Can we learn to determine the position of such a line? In some multivein districts the line for any given vein may be approximated by simple interpolation or extrapolation. Where this is possiblc the bottoms of the lowest ore shoots in the various veins are points on an imaginary, gently rolling surface. The trace of this surface upon the vein is our critical line for that vein. The imaginary surface rolls so gently that it may be projected from two or more known veins to an unexplored vein near by. Here is a criterion for the bottoming of ore that has nothing to do with changes in the appearance of the vein in question; it rests solely on the depth at which the ore bottomed in adjacent veins. The method is not applicable in districts only slightly explored in depth, nor where the lower limit of the ore-bearing horizons

Jan 1, 1941

By W. J. Kroll

W. J. Kroll (Belgium)—Those who are acquainted with the metallurgy of our forefathers may have occasionally a good time when glancing at recent publications in which aged discoveries are unconsciously reported as novelties. We know very well, that oxygen blowing of iron has been described by old Bessemer. The author of the present article is, however, not aware of the fact that the process he describes, the fused salts scrubbing, was already used in the middle of the last century by St. Claire Deville in his attempts at making higher-purity aluminum from raw AlCl3 by sodium reduction. The same fact escaped the three investigators to whom the author refers. The technical grade AlC13 produced by St. Claire Deville from impure oxide, chlorine, and carbon (Oersted process) was contaminated with Sic4 and FeC13, which he removed on an industrial scale by various methods.' He sublimed, for instance, his chloride in contact with iron nails, or aluminum chips, or in hydrogen, which reduced the FeC13 to the less volatile FeCl2. He used also alkali-alkaline earth chlorides as a solvent for A1C13 and FeC13 in presence of iron as a reducing agent, and sublimed his purified AlC13 from solvent salts. The successors of Deville used also zinc or lead as a reducing agent. These methods were later used currently for the purification of BeCl2 and for collecting this compound in a salt bath, suitable for fusion electrolysis. More recently, the same Deville process has been described as applied to the purification of ZrCL4, as part of a method of extraction of ZrCL4 from silico zirconium, which later was reacted with FeC12 in a separate part of the equipment. According to the patent referred to3 the ZrCL4 is dissolved as a gas in a carrier salt such as alkali-alkaline earth chloride, from which it can be reclaimed in a purified form by distillation. A bath of NaCl/KCl is recommended in the specifications. The FeC12-FeC13 go in the salt solution in which raw ZrCl4 is introduced by bubbling, while Sic4 and Tic4 pass through the bath and escape in the atmosphere. purification by this salt-solvent method is thus well described. It may be worth while insisting on some minor details about which the author did not bother too much. One of these concerns the material of construction for the container. If iron is used, and if no other reducing agent is added, then it is the iron of the pot that acts as a reagent in the breakdown of FeC13 to FeCl2, and corrosion can be expected. This shows the importance of using extraneous large surface-reducing agents, of which there is a choice. Zir-

Jan 1, 1963

By Richard M. Foose

Five miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. Geology Lower Cambrian Antietam quartzite and the Rilontalto quartzite, stratigraphi-cally older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65" to vertical. The clay crops out at an elevation of about 1000 feet. Origin and Character The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there Are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about loo ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: SiO2, 67.05 per cent; Al2O3, 22.27; Fe2O3, 0.40; CaO, 0.00; TiO2, 1.05; MgO, 0.52; Na20, 0.04; K2O, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1948

By H. S. Cannon, F. N. Rhines

The application of a static load to a copper powder compact during sintering at an elevated temperature accelerates the rate of sintering in such a way that a given load induces the same proportional increase in rate for all times of sintering. It is shown that sintering under a load is like creep under a fixed load in that the stress required to accomplish a given degree of densification is proportional to the logarithm of the sintering time. VIRTUALLY all of the theories of sintering that have been put forward within recent years have contained the assumption that the chief driving force of the process is the surface tension resident in the exposed surfaces and internal pores of the compact, or powder mass. An externally applied load might be expected to provide a somewhat equivalent driving force for sintering. It is known that the application of a compressive load, during sintering, hastens densification, but it is by no means clear whether sintering under the influence of surface tension alone and sintering under an applied load are fundamentally similar processes. The present study was undertaken in an effort to obtain an answer to this question and with the hope that the answer may contribute to an understanding of the mechanism of sintering. It has been found that there is a close relationship between sintering and creep processes. Copper powder compacts were sintered in hydrogen at 1000 °C under dead loads of 0 to 165 psi and the progress of sintering was observed by means of density measurements. Using a commercial reduced oxide copper powder, see Table I, cylindrical compacts Yz in. x x in. high were made at a pressure of 12,500 psi. For sintering, these were placed in a cylindrical graphite container into which they fitted snugly. A compressive axial load was applied to the compact through a graphite rod of similar diameter, which rested upon the upper end face of the compact; iron weights, in suitable amount, were placed upon the graphite rod to provide the load. This assembly was encased in a vertical silica tube within a resistance-type furnace capable of maintaining a substantially constant temperature within the working zone. After various predetermined times at temperature, the samples were removed from the furnace and their density was measured by conventional means. The heating-up and cooling-down times have been included in the computed sintering time, using the assumption that the sintering rate doubles for each increase of 10 °C in temperature. The experimental results are presented in Table 11. Upon metallographic examination of the specimens, it was found that there was no apparent change in the shape of the pores as a result of loading, i.e, no flattening, Fig. 1. Substantial contraction away from the container walls was observed in all samples sintered with loads of 10.5 psi and less.

Jan 1, 1952

By Richard M. Foose

Five miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. Geology Lower Cambrian Antietam quartzite and the Rilontalto quartzite, stratigraphi-cally older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65" to vertical. The clay crops out at an elevation of about 1000 feet. Origin and Character The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there Are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about loo ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: SiO2, 67.05 per cent; Al2O3, 22.27; Fe2O3, 0.40; CaO, 0.00; TiO2, 1.05; MgO, 0.52; Na20, 0.04; K2O, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1948

By Nicholas J. Grant, H. C. Chang

EMPHASIS on the importance of grain boundary sliding as a mode of deformation at elevated temperatures has been presented elsewhere.' The extent to which boundary sliding occurs under certain creep conditions has been determined for high purity aluminum2,3 and aluminum alloys.' In general, boundary deformation extends quite far into the adjoining grains, resulting in a rather wide band of deformation along the grain boundaries. This has led some investigators to doubt that grain boundary sliding consists of shearing along the boundary surface; it has been contended instead that boundary sliding is a result of concentrated slip in the neighborhood of the deformed grain boundaries."' The purpose of this note is to present evidence that grain boundary sliding takes place by a bulk shear process. gh purity polycrystalline aluminum, wherever and whenever there is grain boundary sliding, boundary migration and concentrated deformation along both sides of the deformed boundary are associated with it. Therefore, it has been rather difficult to obtain unambiguous evidence of boundary sliding. On the other hand, it would be expected in certain alloys of aluminum, when tested under particular conditions. that the severity of the interfering effects of boundary migration and concentrated deformation along the deformed boundary might be reduced. Current research in this laboratory' shows that a 20 pct Zn-A1 solid solution alloy fractures in an intercrystalline manner during creep at 500°F with a small total elongation of not more than about 14 pct, and that it does so with extremely limited grain boundary migration. Accordingly, this alloy was chosen for the present study. The experimental procedure was similar to that used in previous work and has been presented elsewhere.' Two parallel flat surfaces were milled from a round specimen. The gage portion of the specimen was 1 in. x .09 in. x .17 in. The specimens, which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar. The specimens were subjected to creep at 500°F at stresses of 2000 to 5000 psi. The rupture times were from 10 sec to 3 hr. Appreciable boundary sliding occurred in all the tests. A typical example of boundary sliding is shown in Fig. 1. (The tension axis is vertical in the micrographs.) Sliding has taken place along the boundary between grains A and B unaccompanied by important boundary migration. The sharpness of the offset at the triple point can be clearly seen in grain C. As a result of sliding along the boundary between grains A and B, a new boundary surface between grains A and C was created. The offset at the triple point is about 0.07 mm. This boundary sliding is accompanied by the formation of rather sharp kinking bands and, of course, slip on several slip systems in grain C. This type of deformation has been referred to as fold formation' in previous work with high purity aluminum.

Jan 1, 1957

By C. J. Osborn

The temperature dependence of the free energies of formation of metallurgically important oxides, sulphides, chlorides, carbonates and sulphates is presented graphically, whereby the task of deriving practical metallurgical information is greatly simplified. The diagrams have been revised according to the latest available thermodynamic data. WHILE it is true that much careful investiga-tional work remains to be done, there are already available in the literature sufficient thermo-dynamic data to enable the metallurgist to predict with reasonable confidence the equilibrium conditions to be expected in most important, and potentially important, metallurgical reactions. In this connection, the careful, critical compilations of K. K. Kelley and his collaborators in numerous U. S. Bureau of Mines Bulletins are particularly valuable. However, the translation of reliable thermo-dynamic data into metallurgical language unfortunately involves lengthy manipulations of the cumbersome formulas which can be set up from heat of formation, entropy, and heat capacity data. Many years ago, Kelley20 predicted that thermo-dynamic calculations would be made in the future "with the aid of free energy, heat content, and entropy tables, rather than by means of the algebraic methods employed at present", and where such tables are available they greatly simplify the task of deriving practical metallurgical information. However, in addition to these tables, there are also available one or two reliable graphical presentations, particularly of free energy data, which may be used in the same way as the tables, but which have the added advantages that interpolation is never necessary, and that the behavior of different metals or compounds may be compared at a glance. Some years ago Professor Robert Lepsoe, Head of the Department of Metallurgy at Norways Institute of Technology (N.T.H.), began a compilation of curves showing the temperature dependence of the heat contents of the elements, and the heat contents and heats and free energies of formation of the common metallurgical compounds. With such a compilation, the thermal and free energy requirements of a reaction may be read from curves in a matter of seconds; and this statement applies not only to the formation of compounds from their elements, and to the reverse dissociation, but to any reaction involving substances whose thermodynamic properties are available. This follows from the fact that heats and free energies of formation are completely additive. For example, the free energy change associated with the chlorination of a metallic oxide at any temperature, T, is given by the free energy of formation of the chloride at temperature T minus that of the oxide also at T; both of these quantities may be read directly from curves of the type suggested above. Since this early, unpublished work of Lepsoe, both Ellingham7 and Richardson and Jeffes46 have

Jan 1, 1951

By Lester C. Uren

THIS paper reviews the industrial trends and changes in educational concepts that have led to the development of the modern petroleum engineering curriculum. A trend toward emphasis on engineering fundamentals is noted. While most universities are committed to the traditional four-year engineering program, it is agreed that more than four years is necessary for academic preparation of the petroleum engineer in all phases of his profession. The author proposes a coordinated program of undergraduate and graduate training that will permit of adherence to the general pattern of the present four-year engineering course, with provision for extension of the program into specialized graduate courses of professional character. In the latter, emphasis may vary with the interests and objectives of the individual student. A specific undergraduate curriculum is proposed in which upward of 80 per cent of the available time is devoted to engineering fundamentals. A broad survey of the professional field is afforded in courses grouped in the third and fourth undergraduate years, but detailed treatment of the professional aspects of petroleum engineering is reserved for the graduate program. INTRODUCTION Of necessity, engineering curricula must ever be changing to reflect the new techniques, the changing concepts that are presented as the engineering industries develop and unfold. Particularly is this true of the younger engineering curricula representing comparatively new and rapidly changing industries such as the petroleum industry. Institutions that planned their petroleum engineering curricula a decade or two ago now find that the petroleum industry has become vastly more technical in its requirements. Entirely new methods and techniques have come into vogue and must be given place in the curriculum, and some of these are of a character that demands changing emphasis in the fundamental preparatory subjects. College and university faculties cannot complacently assume that curricula in this field that were considered appropriate 10 or 20 years ago still reflect the needs of the industry that they are designed to serve. If they do, their graduates will be poorly equipped to meet the requirements imposed upon them by a rapidly changing industry. Perhaps it is not too much to expect academic authorities to anticipate the trends of industry and equip their graduates with what they will need to attain leadership 10 or 20 years after graduation. Whether or not this desirable objective is possible, there is no excuse for allowing curricula to fall behind the current needs of industry. DURATION OF CURRICULUM The majority of our engineering schools and colleges still adhere to the four-year curricula and there appears to be a definite - sentiment among many engineers engaged in industry that work should be so planned that the engineering student may secure the essential academic preparation for his profession in a terminal four-year program. Yet, in recent years, it has become increasingly apparent that four years of

Jan 1, 1941

By R. N. Hunt

GEOLOGICAL and exploration work of the United States Smelting Refining and Mining Company are handled by the mines geological and the exploration divisions of a geological department under the direction of the chief geologist. The mines division at present includes, in Utah. a geologist in charge, resident at Bingham, assisted by a geologist stationed at each operation, and a small group of geologists resident at the Bayard unit, in New Mexico. The duties of the mines division include the mapping and delineation of the geology of the mines, direction of sampling and diamond drilling, and the periodic calculation of ore reserves. At Bingham an amount of underground drilling within the limestone and porphyry formations which are hosts to the ore bodies supplements and completes development by mine workings. At Bayard, five to seven drills are kept busy underground, and eight to twelve drills operate on the surface. The mines division men live at the mine and work in close co-operation with mine superintendents and foremen. Development work is discussed, initi-

Jan 1, 1948

By Louise Barton Freeman, Iley B. Browning, Coleman D. Hunter

During 1942, production of oil in Kentucky reached a total of 4,169,163 bbl. of which 1,807,809 bbl. came from eastern Kentucky. This was more than a million barrels less than in 1941, owing partly to the low price of crude oil, which almost eliminated wildcatting, and partly to spacing regulations, which limited the number of wells drilled in small, shallow pools where the pressures are not sufficient to maintain maximum recovery in widely spaced wells. In eastern Kentucky much of the oil was produced from outliers of the Mauch Chunk series at the disconformable contact of the Mississippian and Pennsylvanian. Although wells producing from this horizon, known as the Maxon, are sprinkled over the entire area, the greatest concentrations are in Martin, Floyd, Knott and Pike Counties. A new 30 to 40-bbl. well has been completed in this formation in ,Pike County, where the carbon ratio is so high that ordinarily oil would not be expected. Pike County is one of the largest producers of Maxon gas, and the offset well to this oil well produced gas. Of the 412 gas wells drilled in Pike County, 12.2 per cent produced gas from the Maxon horizon. During 1942, the old Menifee " Cornif-erous" field, the Mariba-Denniston field, was redrilled between old wells, and although it did not produce any large amount of oil it did contribute 2018 bbl. In the oldest oil field in eastern Kentucky, the Ragland pool, operators are cleaning out abandoned wells and are using this oil for fuel oil. There is a possibility that some of this may be used in the future as distilled fuel oil. Eight wells were completed in 1942 in the Jackson County gas field. The development of Jackson County, which was started in 1934 and in which commercial quantities of gas were encountered at a depth of 1100 to 1200 ft., has become of importance in 1942 with the completion of eight wells, making a total of 24 commercial producing wells with an average rock pressure of 140 lb. At this time the gas is not being marketed. In the last year it has been found that these wells, which produce from the Niagaran dolomite ("Cornif-erous"), respond to acidizing and the production has been thus greatly increased. There has been less development in Estill and Lee Counties than for several years. Two wells were drilled in Greenup County, one of which had a show of oil in the Berea sandstone. One deep test, drilled by the Owens-Libbey-Owens Co. in Lawrence County, was dry. This well was drilled to a depth of 4975 ft. into the top of the Clinton shale sequence. Of the 202 wells completed in Floyd, Martin, Knott and Pike Counties, 187 were gas wells, 3 oil wells and 12 dry holes. In Floyd County 66 per cent of the gas production was from the Devonian-Mis-sissippian black shales, 53 per cent in Martin, 79 per cent in Knott and 65 per cent in Pike. This is probably the largest continuous gas field east of the Mississippi

Jan 1, 1943

By J. C. Uy, A. A. Burr

IN the primary solid solutions of zirconium-base alloys, there is a striking regularity of the effect of solute valence on the stabilization of the allotropic phases.1 The valences derived by pauling2 are for elements as they are bonded in the solid metallic state. Effects of variations in isotopes, alloying elements, and allotropes on their valences are difficult to determine and such data are presently unavailable. Pauling's values are somewhat empirical and approximate, but if some definite correlations can be found between those values and experimental observations, this will lend support to the tacit assumption that the possible variations in valence mentioned above are small. Pauling has amassed a large amount of evidence of such correlations. It is the purpose of this technical note to show another application of the Pauling valences and to offer a possible explanation for this observation. The relationship between the Pauling metallic valence of the solute and the stabilization of allotropic phases in zirconium is shown in Table I, which has been compiled from available data in the literature3 plus the results of work done at Rens-selaer Polvtechnic Institute.' The chemical valences are included for comparison. It can be seen that a solute whose metallic valence is lower than that of the solvent tends to stabilize the a phase while one whose metallic valence is higher than that of the solvent tends to stabilize the 0 phase. It should be noted that, inasmuch as the Pauling valences are periodic with atomic number, this is tantamount to saying that the elements in groups I-A, 11-A, III-A, III-B, IV-B, V-B, and VI-B are a stabilizers while those in groups IV-A, V-A, VI-A, VII-A, VIII-A, I-B, and 11-B are ß stabilizers. The chemical valences do not show such consistency. Although the zirconium-rich end of the Zr-Au diagram is not available, it call be expected that gold, having a metallic valence of 5.56, would stabilize the ß phase. At absolute zero, the Fermi energy level is the criterion of equilibrium, i.e., the structure having the lower Fermi level will be more stable. Conse- quently, allotropic transformation occurs in a metal when thermal excitation raises the Fermi level to a point at which the atoms can be better accomodated by a different structure which yields a lower Fermi level.4-6 Thus in allotropic transformation, a change in structure occurs as a result of the change in the energies of the bonding electrons. Since the Pauling valence is the number of bonding electrons per atom, and these are the only electrons whose energies are affected by thermal excitation,* it can be inferred that the introduction of a solute which has a higher Pauling valence than that of the solvent raises the initial Fermi level; consequently, the transformation temperature is lowered. The converse is also true. The fact that at the transformation temperatures this statement is still fairly valid implies that the contribution due to the difference in specific heat terms of the two allotropes is comparatively small.

Jan 1, 1962

By Iley B. Browning, Louise Barton Freeman, Coleman D. Hunter

During 1942, production of oil in Kentucky reached a total of 4,169,163 bbl. of which 1,807,809 bbl. came from eastern Kentucky. This was more than a million barrels less than in 1941, owing partly to the low price of crude oil, which almost eliminated wildcatting, and partly to spacing regulations, which limited the number of wells drilled in small, shallow pools where the pressures are not sufficient to maintain maximum recovery in widely spaced wells. In eastern Kentucky much of the oil was produced from outliers of the Mauch Chunk series at the disconformable contact of the Mississippian and Pennsylvanian. Although wells producing from this horizon, known as the Maxon, are sprinkled over the entire area, the greatest concentrations are in Martin, Floyd, Knott and Pike Counties. A new 30 to 40-bbl. well has been completed in this formation in ,Pike County, where the carbon ratio is so high that ordinarily oil would not be expected. Pike County is one of the largest producers of Maxon gas, and the offset well to this oil well produced gas. Of the 412 gas wells drilled in Pike County, 12.2 per cent produced gas from the Maxon horizon. During 1942, the old Menifee " Cornif-erous" field, the Mariba-Denniston field, was redrilled between old wells, and although it did not produce any large amount of oil it did contribute 2018 bbl. In the oldest oil field in eastern Kentucky, the Ragland pool, operators are cleaning out abandoned wells and are using this oil for fuel oil. There is a possibility that some of this may be used in the future as distilled fuel oil. Eight wells were completed in 1942 in the Jackson County gas field. The development of Jackson County, which was started in 1934 and in which commercial quantities of gas were encountered at a depth of 1100 to 1200 ft., has become of importance in 1942 with the completion of eight wells, making a total of 24 commercial producing wells with an average rock pressure of 140 lb. At this time the gas is not being marketed. In the last year it has been found that these wells, which produce from the Niagaran dolomite ("Cornif-erous"), respond to acidizing and the production has been thus greatly increased. There has been less development in Estill and Lee Counties than for several years. Two wells were drilled in Greenup County, one of which had a show of oil in the Berea sandstone. One deep test, drilled by the Owens-Libbey-Owens Co. in Lawrence County, was dry. This well was drilled to a depth of 4975 ft. into the top of the Clinton shale sequence. Of the 202 wells completed in Floyd, Martin, Knott and Pike Counties, 187 were gas wells, 3 oil wells and 12 dry holes. In Floyd County 66 per cent of the gas production was from the Devonian-Mis-sissippian black shales, 53 per cent in Martin, 79 per cent in Knott and 65 per cent in Pike. This is probably the largest continuous gas field east of the Mississippi

Jan 1, 1943

By P. Niessen, S. J. Bercovici

RECENTLY Aust et al.&apos; proposed a model of non-equilibrium grain boundary segregation based on a vacancy gradient induced uphill diffusion process of solute to grain boundaries. According to their proposal, solute atoms which are attracted to vacancies would, during the cooling of a sample, migrate with vacancies toward grain boundaries (vacancy sinks) and thereby enhance the solute concentration in boundary regions. For solute atoms which are not attracted to vacancies no such boundary solute enrichment would be expected. These concepts were given experimental support by boundary and bulk mi-crohardness measurements of various thermally treated dilute zinc and lead alloys and also doped aluminum oxide. The underlying assumption in their work was that solute enrichment in boundary regions is indicated by higher microhardness values. From thermodynamic considerations1&apos;2 it appears that the solid-liquid solute distribution coefficient (K), defined as the concentration of solute in the solid to the concentration of solute in the liquid at equilibrium, indicates whether attractive or repulsive forces exist between vacancies and solute atoms. K < 1 indicates a solute-vacancy attractions, K > 1 indicates no, or a repulsive, vacancy-solute interaction. This note is to report on observations of different grain boundary etching phenomena in high purity zinc alloys. These phenomena appear to depend on whether a K < 1 or K > 1 solute is present. In experiments designed to measure directly the solute enrichment in grain boundary regions, samples of zone refined zinc with 0.1 at. pct solute additions were cooled from 380°C at a rate of 3°C per min. A surface layer of approximately 50 was then removed from the samples by chemical polishing. The samples&apos; surfaces were then protected by a chromating treatment such that in a subsequent etch only grain boundary regions were dissolved. The dissolved regions were approximately semicircular troughs, 10 µ in width. The grain boundaries were usually in the middle, i.e., at the bottom, of this trough. For zinc containing the K < 1 solutes cadmium and aluminum, the grain boundary was always indicated by a ridge as shown in Fig. 1. For pure zinc, and zinc containing the K > 1 solutes copper and gold, a groove at the bottom of the trough indicated the boundary position, Fig. 2., To test if these different grain boundary etching behaviors were possibly connected with the segregation process discussed above, the Zn-Cd alloy was again heated to 380°C and quenched into brine. After surface protection and etching it was found that this specimen no longer exhibited the grain boundary ridges but rather grain boundary grooves as shown in Fig. 2. It would appear, therefore, that the boundary ridge is a consequence of a process occurring during the slow cooling of the samples. From absorption spectrophotometric analysis it was found that for slowly cooled samples containing K < 1 solutes, the solute/zinc ratios of the material from the boundary trough were consistently considerably higher than the solute/zinc ratios of the bulk alloys. This boundary region solute enrichment was not observed in quenched samples. It is concluded therefore, that the boundary ridge shown in Fig. 1 is directly or indirectly connected with nonequilibrium solute segregation.

Jan 1, 1970

• As part of $850,000 granted by the House Appropriations Committee for development of manganese in the U.S., the Bureau of Mines will build a pilot plant at Artillery Peak, Ariz., for development of low grade manganese ores. • The historic Argo tunnel and mill in Idaho Springs, Colo., will reopen shortly for the mining of uranium. The Uranium Co. of America has acquired control of the tunnel and mill and 12 nearby mining properties. J. H. Rodgers and G. C. Ridland will manage the operation. •The opening of a new 4000-ton per day coal mine in Washington Co., Pa., and the reopening of another mine of the same capacity in Fayette Co. has been announced by the H. C. Frick Coke Co. They&apos;ll help meet added war demands. •A 7000 bbl per day commercial synthetic liquid fuel plant, making gasoline from natural gas at Brownsville, Texas is being operated by the Carthage Hydro-col Corp., a Texaco subsidiary. The gasoline is produced by the Hydrocol process, chemically similar to the Fischer Tropsch process, but differing mechanically in several ways. To operate the process it has been necessary to build an oxygen plant producing 95 pct pure oxygen in quantities equal to U. S. production of commercial oxygen in 1946. •Over 96 pct of the class of 1950 at Montana School of Mines are now employed,, in industry, and they&apos;re scattered from MIT to the island of Cuba., • Cobalt, heretofore almost entirely imported, will soon be produced in Idaho. The Calera Mining Co. is building a 600-ton mill in which a cobalt and copper concentrate will be obtained from Idaho ores. •Plans for mining iron ore on the Conarky Peninsula in French Guinea, (an ECA project) call for equipment purchases as follows: 8 wagon drills, electric shovel for mining, conveyor for the port, 8 trucks, wrecker, 2 tractors, as well as miscellaneous accessories and spare parts. •A low-grade lead-zinc mineralization, located east of any known ore bodies in Utah&apos;s East Tintic district, has been located by a 2000-ft wildcat USGS drill hole. * Higher-than-going rates have been authorized by the Munitions Board for its stockpile program, where domestic production of scarce materials is low or uneconomical. Payment in excess of 25 pct over the foreign price is now permitted. •A new self-centering conveyor roll, developed by Carnegie-Illinois Steel, is expected to revolutionize materials handling. It completely eliminates the necessity for sideguides to keep materials on a conveyor. See P. 1028. •Great Britain&apos;s socialized coal industry employs twice as many miners, but produces less than half as much coal as America&apos;s coal industry. last year, British mines produced 28 million fewer tons of coal than the output of the same ,mines in 1939. Absenteeism amounted to a big 12 pot of working time. • Labor market conditions have tightened on almost a country-wide scale. Only 4 out of 143 major labor market areas have a substantial surplus -- less than half the total for May. Growing scarcities of skilled labor are in evidence.

Jan 10, 1950

BEING at the crossroads, metaphorically speaking, seldom has the advantages of the literal sense of the words. One seldom has precise knowledge of the existence of the metaphorical crossroads or forks in the road of life. A case in point is the Committee on Education of the Engineers&apos; Council for Professional Development, which for twenty years has been accrediting the engineering curricula in the educational institutions of the United States. The committee is now at odds with itself and with the National Council of State Boards of Engineering Examiners over the accrediting of courses which in the opinion of many engineers are not strictly speaking engineering curricula at all. Such courses include: fire protection engineering, crystal engineering, nuclear engineering, and geological engineering. The crossroads might be placed arbitrarily somewhere between 1936 and 1938 when the committee first started accrediting curricula and included the first course in industrial engineering. Purists might argue that the committee first wandered from the straight and narrow when it recognized subdivision of engineering into the major branches of mining, metallurgical, civil, mechanical, electrical, and chemical engineering. Accrediting is certainly an important function because it provides a standard for engineering education and it should be done on a national basis by an unbiased group like the Education Committee of ECPD. Students, educational institutions, and industry derive great benefit from proper standards. The autonomous State Boards of Engineering Examiners have long accepted ECPD accreditation as evidence of the required academic training of engineers aspiring to licensing. But the State Boards today question the wisdom of applying the name engineer to graduates of some of the so-called fringe curricula. The Education Committee, having gone so far in accrediting some of them, has numerous applications pending for accreditation of similar curricula and even new courses never before accredited. Arguments against recognizing highly specialized engineering curricula are numerous. The Salary Stabilization Board has disallowed industrial engineering from classification as engineering for its purposes. A graduate of a specialized course in geological engineering at a school in the Southwest slanted heavily for practice in the petroleum industry might not be interchangeable with a graduate of a similarly designated curricula at one of the institutions in the North Central states where the emphasis might be on metallic. mineral deposits. Industry in general should not expect the universities to supply a degree in each of the specialized engineering classifications it might set up for purposes of salary or job designation. Having gone so far, it is easy to understand the difficulty of the Education Committee. ECPD might well call a moratorium for the purpose of taking stock of its position. If the present trend is allowed to continue, it is apparent that an engineering institution could be subdivided into a multiplicity of departments teaching specialized curricula resulting in a subordination of the basic concepts of engineering. Although the parallel of the medical profession is trite, it should be pointed out that degrees in medicine are not labelled by the numerous specialities practiced by doctors. For practical purposes the ECPD would do well to accept the fact that the crossroads have been overreached "and protect the engineering profession by coming up with minimum standards for an engineering curriculum.

Jan 1, 1952