Search Documents

By Earl C. Herkenhoff

Publication of the article "The Flotation Behavior of Digested Asphalt Ridge Tar Sands" by R.J. Smith and J.D. Miller has confirmed and again spotlighted a most significant and important development in the field of tar sand and heavy oil mining. This is the ability to recover 95% of the bitumen in dry tar sands by a hot water process. The initial investigation by Miller and Sepulveda in early 1978. "Separation of Bitumen from Dry Tar Sands," was the first blockbuster. It is disappointing that there has been so little scientific and industry ackowledgement that the authors laid to rest the long entrenched belief that the sand grains had to be "water wetted" for a hot water process to be applicable. Dr. Miller and his researchers at the University of Utah used slightly different mineral dressing terminology in describing their process but it is essentially the old, established technique of high &lids attrition scrubbing at elevated temperatures with a conditioner or modifier, followed by dilution and froth flotation. Similar techniques were described in detail for other nonmetallic minerals in the mid-1940s by Stuart Falconer of American Cyanamid Co. The authors used a 15-minute "scrub" period (or in their terminology "digester step") at 73% solids and 95OC (203°F) in a 0.3 m solution of sodium carbonate-about 4 kg/t (8 lb per st) of tar sand. Flotation was at 10% solids. Obviously, the scrub is an expensive step with respect to energy input but the high recovery of bitumen appears to justify it. Two basic questions then arise: What are the effects of shorter scrubbing time, lower temperature, and less sodium carbonate? Would a two-stage approach be advantageous? That is, could you get the major proportion of the bitumen with a mild scrub and apply the high power and temperature only to the refractory portion? These variables should be evaluated. Apparently, all results were only for rougher flotation. What would the grade and recovery of bitumen be if multiple cleaner flotation steps were employed? We must concede that a 60.62% grade of bitumen leaves considerable room for upgrading. Finally, it should be noted by all executives who approve funds for heavy oil recovery schemes, most of which are variations of in-situ methods, that mining can yield a 95% recovery of bitumen. That is correct, 95%. Imagine what that does to the total barrels recovered from a heavy oil resource compared with the scrawny 30-35% maximum recovery we are getting now. The conclusion-let's mine heavy oil and tar sands.

Jan 1, 1983

By Pierre R. Hines

The first progress in American ore dressing practice was made in the mills of the Mother Lode in Calif., the Comstock Lode in Nev., and Gilpin County in Colo., during the years 1861 to 1870, when the ancient wooden stamp battery, with square wooden stems, was converted into the 'California' stamp made of wrought and cast iron, with round stems which rotated. Eli Whitney Blake invented the jaw crusher in 1858 for stone crushing, and it was soon used for crushing ore. F. W. Gates' gyratory crusher followed twenty years later. S. R. Krom, Thomas A. Edison, and others improved the Cornish rolls by increasing their size and spring pressures; the Symons Brothers made horizontal and vertical disc crushers; W. Ball and E. T. Leavitt designed powerful steam stamps for Lake Superior native copper ores; and jigs were mechanized. William B. Frue, a mill superintendent in the Lake Superior copper district, invented the vanner in 1874. Arthur F. Wilfley built his riffled concentrating table in 1895, just after Dr. Robert H. Richards commenced his Ore Dressing. The Wilfley table so changed concentrator flow sheets that Dr. Richards was compelled to revise his text, and its publication was delayed until 1903. The value of sizing or classifying before concentration was recognized. Dr. Richards had persuaded the Anaconda Copper Mining Co. to install round tables with special surfaces to catch the 'extremely fine free mineral.'l Gravity concentration had achieved almost every refinement for recovering or separating minerals by the difference in their specific gravities. However, one serious problem remained unsolved, i.e., how to retrieve the enormous loss of the extremely fine mineral in the slime portion of the ore. Slime, then, as now, was not a precise term due to the variation in the mineral composition of the ores and the different requirements in crushing, grinding, sizing, and classifying. At that time, slime was considered to be fine sand and colloidal material passing 100 mesh.2 Most sulfide ore minerals are more friable than their associated gangue minerals, so that crushing and grinding increased the proportion of the extremely fine ore minerals in the slime. Sparkling specks of galena, chalcopyrite, argentite, or ruby silvers, according to the ore, floating away on the tailing stream from vanners and slime tables, were familiar sights in the old gravity concentrators. Gravity concentration practice was aimed at recovering the ore minerals at the coarsest possible size because the recovery was higher and unnecessary

Jan 1, 1962

By G. Richards Gwinn

Graphite is one .of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world's high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. Types oF Graphite Used in Crucibles Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1948

Christopher R. Corning was one of the ablest mining engineers and geologists in America and one whose name was well known also in Mexico, Cuba, South America and many European countries. He was educated at Zurich, Switzerland, and at the Bergakademie, Freiberg, where he was graduated in 1883 with the degrees of Markscheider and Bergingenieur. He continued his studies at Heidelberg until 1886, chiefly in chemistry, under Bunsen, and mineralogy and petrography under Rosenbusch. Although he received a Ph.D. in chemistry, he never used the title. During holidays of 1883-86, he traveled, seeing mines and studying geology in Spain, France, England, Italy, Germany, and Austria. In 1886, he returned to America and in 1887 he was in the Lake Superior iron ore country on the staff of John F. Stevens, then building the Duluth South Shore and Atlantic Railway. In 1889, Mr. Corning was at the Bunker Hill & Sullivan mines at Wardner, Idaho, with John Hays Hammond, and there met E. E. Olcott. Although Mr. Corning was not long connected with the Bunker Hill & Sullivan mines, he left the imprint of his ability and splendid personality upon the men and the property. That his friendship was cherished was manifested by the cordiality, hospitality and frequency of letters of good counsel and cheer. In 1897, Mr. Corning, with E. E. Olcott and Prof. Robert Peele of Columbia University, formed the firm of Olcott, Corning & Peele, consulting mining engineers. Pressure of university duties compelled Professor Peele to withdraw in 1904, and later Mr. Olcott was forced to retire by reason of other important business interests, but the friendship and high mutual regard of the three men continued undiminished. About 1902, Mr. Corning and Professor Peele translated into English Riemer's book on "Shaft Sinking under Difficult Conditions." Mr. Corning's knowledge of structural geology, mineralogy and ore deposits was extensive and accurate. He was a close and intelligent observer. When he became interested in a problem, no amount of trouble was too great in endeavoring to reach a satisfactory solution. He had professional experience in the West, notably in the Coeur d'Alenes, Mexico and South America, and several times was called on to attempt to straighten up mismanaged properties. In 1912, at the request of a large number of members, Mr. Corning headed the "Committee of FiveJ' that investigated the affairs of the American Institute of Mining Engineers and brought about beneficial changes in the organization and its policies. He was one of the organizers

Jan 1, 1924

By Edward Saibel

THE object of this study is to investigate the effect of prior tensile strain on the fracture stress of a metal. This is done in a theoretical manner starting from the point of view developed by the author in his thermodynamic theory of the fracture of metals. The results are compared with experimental findings and a rational interpretation is given to work that shows the variation of fracture stress with prior tensile strain. THEORY OF FRACTURE In the thermodynamic theory of the fracture of metals developed earlier,1 it was shown that a critical strain energy per unit volume exists. This is characteristic of the material and may be calculated from basic thermodynamic data. When the area under the flow curve reaches this characteristic value, fracture occurs. The general criterion for fracture is expressed in the form u ± uo = JLm?AV/V [1] where Lm, is the latent heat of melting of the unit volume, ?V/V is the ratio of the change in volume of the unit volume to the original unit volume on passing from the solid to the liquid state, [uo] is an initial energy density, and J is a conversion factor, which changes energy from heat to mechanical units. As a first approximation, it will be assumed that the stress-strain curve is the straight line that extends from the point of maximum load onward, extrapolated back to the axis of zero strain, for example, line AC of Fig. 1. If the point of intersection of the straight line with the axis of zero strain is represented by so, and the slope of the straight line is p, the analytic form of the flow curve is [s = s + pd [2]] and the strain energy per unit volume evaluated from [JvdS] becomes (vsod + pd2/ 2). When this latter term reaches the critical value JLm?V/V (designated hereafter by M), it is assumed that fracture occurs. This leads to the following expression for the fracture stress: [s1 = \/C r.2 + 2Mp [31] The strain at fracture may be calculated from Eqs 2 and 3. It is assumed in this paper that the initial energy density is either zero or that it may be neglected. Furthermore, the complicated states of stress and of strain existing in the necked region of the tensile specimen after "necking" has occurred will also be neglected for the present, so that average conditions will be assumed to prevail. FLOW AND FRACTURE CURVES Ludwig2 attributed to materials two fundamental properties: (I) a resistance to flow and (2) a resistance to fracture. He reasoned that at each instant the

Jan 1, 1947

By Howard Eavenson

ONE who has been trained in belief in the law of supply and demand and its effect upon prices finds it difficult to adjust himself to the minute regulations imposed by the New Deal, and also to the bewildering changes of government policy as expressed within a short period of time between the antitrust laws and the N.R.A., and later by the Bituminous Coal Conservation Act of 1935. A survey of the coal industry since the World War, both in this country and Great Britain, however, shows that regula-tion of some sort is needed if any stabilization is to be achieved and if the Wage structure and economic welfare of the many communities dependent solely upon coal are to be maintained. Let us look at what has happened to the industry since 1920, which can be considered as the end of the period affected by the war influence. This discussion will be confined solely to bituminous coal, although many of the general conditions are equally applicable to anthracite, the position of which now is at least as bad as that of the softer variety. Since 1920-to the end of 1934-the production of coal has decreased from 568.7 million to 358.4 million tons, or 37 per cent; the number of mines from 14,766 to 6,258, or 58 per cent; the average annual production per mine has changed from 38,512 to 57,425 tons, or 50 per cent. The number of large mines has increased considerably, and the number of men employed has decreased from 639,547 to 458,011, a reduction of 28 per cent, while the average output per employee has changed from 4.0 to 4.4 tons, or an increase of 10 per cent. The average price per ton of coal at the mine has varied from $3.75 to $1.75. During that time wages decreased largely until 1933 and since that time have increased, until now the rates paid are- considerably above those in other occupations, although the actual yearly earnings are low, because of part-time work. From 1920 to the signing of the Jacksonville wage agreement in 1924, about two-thirds of the men were union members and practically all of the nonunion mines were south of the Ohio River; with the fixing., of the high wage scale of that agreement, which soon proved to be an uneco-nomic one, many of the mines found that they could not retain their business, so gradually changed to nonunion. By 1928 the proportion

Jan 1, 1936

Located 19 km (12 miles) north of the Carlin gold mine and 43 km (27 miles) north of Carlin, Nevada, is Carlin Gold Mining Company's Bootstrap mine. This deposit is similar in character to the Carlin ore, except it occurs in the upper plate formation of the Roberts thrust fault rather than in the lower plate rocks. The deposit was discovered over 50 years ago and operated on a small scale in the early 1960s using vat cyanide leaching. Newmont Mining Corporation acquired the property in 1967, and from an open pit mined 650,000 mt (717,000 st) of ore which was trucked to the Carlin conventional cyanide plant. (See Gold and Silver Cyanidation Plant Practice by F. W. McQuiston, Jr. and R. S. Shoemaker, Society of Mining Engineers, AIME, 1975. ) With the same grade of ore, the gold recovery by conventional methods is somewhat lower than that of the Carlin ore, even with a finer grind. Leaching tests were first conducted by the United States Bureau of Mines in 1968; and in 1971, ‘72, Carlin conducted extensive cyanidation investigations by bottle testing, simulated heap leaching in tall columns, and small scale pad heap leaches. Gold extractions ranged from 55% to 95% with low reagent consumptions. In 1974, a 545 mt (600 st) heap leach test was made at Carlin on pit-run low-grade material assaying 1.37 g per mt (0.04 oz per st). In a six week period the extraction of gold was 47.57'0. Carlin uses atomic absorption analyses on cyanide leach liquors to determine potential leach ore grade rather than fire assaying because it gives a more practical assessment of leach recovery than does fire assaying, which accounts for the total gold content. Before open-pit mining was started, plans were made to heap leach, the ore at Bootstrap which was too low grade for transport to Carlin. The topsoil outside of the designed pit area overlaid ancient lakebed clays which were found suitable for compaction to form an impervious base on which the dumps to be leached could be placed. By using the cost of truck haulage and milling at the Carlin plant and the price of gold 'at that time, a cutoff grade was established which resulted in the gold content of the first 150,000 mt (165,000 st) of the heap leaching ore being 1.51 g per mt (0.044 oz per st). An additional 500,000 mt (552,000 st) of lower grade material, assaying 0.96 g per mt (0.028 oz per st), is available for leaching as economics permit.

Jan 1, 1981

By G. Richards Gwinn

Graphite is one .of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world's high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. Types oF Graphite Used in Crucibles Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1948

By Walter Crafts, John L. Lamont

An investigation has been made of the multiplying factors for some of the more common alloying and deoxidizing elements for use in calculating hardenability of steel according to Grossmann's method. The factors for manganese, silicon, and aluminum that were reported in an earlier communication2 have been confirmed by microscopic determination of the half-martensite structure rather than on the basis of an empirically determined hardness corresponding to a half-martensite structure. Measurement of ideal critical diameter by microscopic examination was found to be necessary for other alloying elements, and multiplying factors for nickel, chromium, molybdenum, zirconium, vanadium, titanium, and boron have been determined. The nature and order of magnitude of the multiplying factors reflect the effect of the alloying elements on the structural character of the steel. Except for nickel and vanadium, the multiplying factors agree fairly well with previously published results. Good correlation between actual and calculated ideal critical diameters has been found in developing the multiplying factors and in checking the results against fairly simple steels. However, some discrepancies have suggested the need for a more thorough study of low-carbon and complex steels. Testing Procedure The investigation was conducted principally on steels made at the Union Car- bide and Carbon Research Laboratories, Inc., in high-frequency induction furnaces using Armco iron and standard alloying materials. However, a few open-hearth steels were used in establishing the effect of nickel, and the hardenability factor for boron was based primarily on open-hearth steels. All bars were normalized prior to the machining of Jominy hardenability specimens. The Jominy test was carried out under conditions standard for the test.3 Austenitizing temperatures judged to be appropriate for the compositions of the steels were used. Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Residual amounts of phosphorus, sulphur, nickel, chromium, molybdenum, and copper were determined on only one heat of each group made with the same materials during the same period. "Acid-soluble" aluminum and zirconium rather than total amounts were determined, as it is considered probable that the acid-soluble amount is more representative of the effective alloy. As tin was present to the extent of only 0.002 per cent, its effect was neglected. The method used to determine boron in the steels shown in Table 9* was developed by Galen Porter, Vincent Napoleon, and Thomas R. Cunningham, of the Union Carbide and Carbon Research Laboratories, Inc., and is a modification of J. Naftel's procedure for boron in soils

Jan 1, 1944

By John L. Lamont, Walter Crafts

An investigation has been made of the multiplying factors for some of the more common alloying and deoxidizing elements for use in calculating hardenability of steel according to Grossmann's method. The factors for manganese, silicon, and aluminum that were reported in an earlier communication2 have been confirmed by microscopic determination of the half-martensite structure rather than on the basis of an empirically determined hardness corresponding to a half-martensite structure. Measurement of ideal critical diameter by microscopic examination was found to be necessary for other alloying elements, and multiplying factors for nickel, chromium, molybdenum, zirconium, vanadium, titanium, and boron have been determined. The nature and order of magnitude of the multiplying factors reflect the effect of the alloying elements on the structural character of the steel. Except for nickel and vanadium, the multiplying factors agree fairly well with previously published results. Good correlation between actual and calculated ideal critical diameters has been found in developing the multiplying factors and in checking the results against fairly simple steels. However, some discrepancies have suggested the need for a more thorough study of low-carbon and complex steels. Testing Procedure The investigation was conducted principally on steels made at the Union Car- bide and Carbon Research Laboratories, Inc., in high-frequency induction furnaces using Armco iron and standard alloying materials. However, a few open-hearth steels were used in establishing the effect of nickel, and the hardenability factor for boron was based primarily on open-hearth steels. All bars were normalized prior to the machining of Jominy hardenability specimens. The Jominy test was carried out under conditions standard for the test.3 Austenitizing temperatures judged to be appropriate for the compositions of the steels were used. Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Residual amounts of phosphorus, sulphur, nickel, chromium, molybdenum, and copper were determined on only one heat of each group made with the same materials during the same period. "Acid-soluble" aluminum and zirconium rather than total amounts were determined, as it is considered probable that the acid-soluble amount is more representative of the effective alloy. As tin was present to the extent of only 0.002 per cent, its effect was neglected. The method used to determine boron in the steels shown in Table 9* was developed by Galen Porter, Vincent Napoleon, and Thomas R. Cunningham, of the Union Carbide and Carbon Research Laboratories, Inc., and is a modification of J. Naftel's procedure for boron in soils

Jan 1, 1944

By Keith Leonard Sutherland

THIS paper is a study of the differential flotation of the sulphide minerals in the presence of salts of silver, lead and zinc. In practice, accidental activation due to these salts is more important than their use as reagents to replace copper sulphate. The general method of investigation has been based upon contact tests, the temperature of 35°C. being chosen in conformity with earlier work. Potassium ethyl xanthate and potassium amyl xanthate were selected as collectors and pure sulphide minerals were used. The experimental procedure has been outlined in earlier papers and all solutions were kept carbonate-free.'' Contact, or spreading of an air bubble, at a mineral surface indicates the presence of an adsorbed collector film. PURITY OF REAGENTS The xanthates were purified in the usual manner.1 Neither the cyanide nor the sodium hydroxide solutions contained sufficient carbonate to give a precipitate with barium chloride solution. The silver sulphate was prepared from pure silver nitrate by evaporation with concentrated sulphuric acid until there was no evidence of brown fumes. This solution was diluted and the difficultly soluble sulphate washed with water so that unchanged nitrate was dissolved. The resultant crystal-line powder was pure white. The lead and zinc salts were prepared by dissolving especially pure lead and zinc in C.P. nitric and sulphuric acid solution and the crystals drained. The standard solutions were checked by titration. It was felt desirable to use the sulphate radical wherever possible, but since lead sulphate was insufficiently soluble for the purpose of the experiments, it was necessary to use some other lead salt. A.R. copper sulphate was used without further purification. RESULTS The results are presented in the accompanying figures; the areas of noncontact (nonflotation) are shaded in Figs. 8, 9, 10 and 11; in the remainder they lie to the right of the curve. Zinc Sulphate The curves in Fig. I are to be compared with those for Fig. 2, for which zinc sulphate is absent. This comparison shows that the influence of the zinc ion is usually small. Its influence is more marked, however, for chalcopyrite in the absence of cyanide. The influence of zinc sulphate is also marked for copper-activated sphalerite, for which tests were made only in the absence of cyanide. The results are of importance in the separation of pyrite from copper-activated sphalerite when zinc sulphate is added in the lead flotation section (p. 204 of ref. I). Sphalerite does not adsorb the collector (i.e., become floatable) under the conditions chosen.

Jan 1, 1942

By Keith Leonard Sutherland

THIS paper is a study of the differential flotation of the sulphide minerals in the presence of salts of silver, lead and zinc. In practice, accidental activation due to these salts is more important than their use as reagents to replace copper sulphate. The general method of investigation has been based upon contact tests, the temperature of 35°C. being chosen in conformity with earlier work. Potassium ethyl xanthate and potassium amyl xanthate were selected as collectors and pure sulphide minerals were used. The experimental procedure has been outlined in earlier papers and all solutions were kept carbonate -free.1,4 Contact, or spreading of an air bubble, at a mineral surface indicates the presence of an adsorbed collector film. PURITY OF REAGENTS The xanthates were purified in the usual manner.1 Neither the cyanide nor the sodium hydroxide solutions contained sufficient carbonate to give a precipitate with barium chloride solution. The silver sulphate was prepared from pure silver nitrate by evaporation with concentrated sulphuric acid until there was no evidence of brown fumes. This solution was diluted and the difficultly soluble sulphate washed with water so that unchanged nitrate was dissolved. The resultant crystalline powder was pure white. The lead and zinc salts were prepared by dissolving especially pure lead and zinc in C.P. nitric and sulphuric acid solution and the crystals drained. The standard solutions were checked by titration. It was felt desirable to use the sulphate radical wherever possible, but since lead sulphate was insufficiently soluble for the purpose of the experiments, it was necessary to use some other lead salt. A.R. copper sulphate was used without further purification. RESULTS The results are presented in the accompanying figures; the areas of noncontact (nonflotation) are shaded in Figs. 8, 9, 10 and 11; in the remainder they lie to the right of the curve. Zinc Sulphate The curves in Fig. I are to be compared with those for Fig. 2, for which zinc sulphate is absent. This comparison shows that the influence of the zinc ion is usually small. Its influence is more marked, however, for chalcopyrite in the absence of cyanide. The influence of zinc sulphate is also marked for copper-activated sphalerite, for which tests were made only in the absence of cyanide. The results are of importance in the separation of pyrite from copper-activated sphalerite when, zinc sulphate is added in the lead flotation section (p. 204 of ref. I). Sphalerite does not adsorb the collector (i.e., become floatable) under the conditions chosen.

Jan 1, 1942

By L. R. Blair

Many hydrated silicates have been synthesized and sold for commercial use. However, this paper discusses only hydrated calcium silicates and, to a lesser extent, hydrated magnesium silicates. Synthetic calcium silicates were first formed by man when he found that mixtures of silica or silicates and lime in water set up to form cements. The material which was responsible for the cementing properties was calcium silicate hydrate, although this fact was not recognized until early in this century. In the early 19001s, synthetic calcium silicates, reinforced with fibers and formed simply by reacting calcium hydroxide and silica in water with fiber at atmospheric or under low pressure autoclave conditions, found increased use in thermal insulations and in building products. These insulations were found to have a low thermal conductivity and would withstand temperatures up to 650°C. This, combined with their very low densities (from 8 to 50 Ib per cu ft) and fairly high strength, also made them suitable for use as building products. Following the disastrous Morro Castle fire of the 1930Js, calcium silicate board products were used as partitioning material in all shipboard construction in the U.S. As autoclaving techniques were improved and developed, it was: learned that under hydrothermal conditions new and useful calcium silicates which could be used under more extreme temperatures (up to 980' C) could be prepared. These had high surface areas and other unique properties which suited them for use as fillers, pesticide carriers, low temperature insulating materials, and adsorbents for the removal of fatty acids from various solutions. Hydrated magnesium silicates have not been studied as extensively as the calcium compounds. Their first important use was in the filtration of dry cleaning solutions for the removal of fatty acids. With the introduction of detergents, it was found that these products lost their advantage because of their high affinity for the detergent chemicals. However, in recent years these chemicals are finding increasing use as decolorizing agents for fats and anti-caking agents for resins. Some materials with very high surface are finding new use as adsorbents. CALCIUM SILICATE HYDRATE COMPOUNDS AND THElR CONDITIONS OF FORMATION Within the past ten years much has been done in the field of calcium silicate hydrate chemistry. As a result of this work it has been found that at least 25 different forms of calcium silicate hydrate can either be formed synthetically or found as naturally occurring materials. The stability and composition relationships among these 25 compounds present a very complicated picture, and many of these very closely resemble other forms and are difficult to dis-

Jan 1, 1962

By J. L. Swedlow, M. L. Williams

Two standard techniques for assessing fracture initiatlon in sheet specimens involve measurements of 1) the applied load of fracture which, via linear fuacture mechanics, is used to find the fracture tough/less SC (or SIC), and 2) the velative displacement of fracture of the opposite free faces of the crack (COD). In the past, the quantitative association between these two parameters has not been determined in detail, owing to the mathematical difficulties of computing. the stress and strain fields in the combined elasto-plastic flow near the crack. Using a numerical technique Irecently developed and applied to a 7075- TO' aluminum plane stress specimern, the two parameters noted have been determined and associated quantitatirely. CONSIDERABLE effort has been expended in selecting a rigorous yet practical manner for predicting fracture. The usual point of departure is the modified Griffith criterion in which the mechanism of energy dissipation is reflected in Sc (or SIC), the parameter of "fracture toughness". Sc. differs from the surface energy used by Griffith in perfectly brittle fracture in that it includes the effect of plastic flow in the vicinity of the crack tip. Because plastic flow alters the stresses and displacements predicted from the usual linear theory of fracture mechanics, and because analysis of the nonlinear stress-strain field has presented great obstacles: only estimates of several pertinent quantities have heretofore been available. Nevertheless, two parameters have often been measured experimentally althougll usually just at the point of fracture. These are the energy release rate, or fracture toughness 9, (or I,), and the crack-opening displacement (COD). Such observations have been used in connection with frarture criteria and have been most helpful in design, although their application requires care with respect to changes in geometrical configuration from that upon which the criteria were based 1,2 Recently, however, a reasonably accurate and comprehensive method for analyzing the elasto-plastic flow has been devised and applied to plane stress specimens having arbitrary octahedral stress-strain curves.3 It thus becomes feasible to compute, albeit numerically, both the fracture toughness and crack opening as functions of the applied tensile loading on a typical specimen geometry. As a result, it is now possible to associate these two parameters quantitatively, and thereby to associate data obtained by one method with data pertaining to the other. ELASTIC ANALYSIS For the case of linear elasticity, it is relatively easy to deduce the connection between various measures of crack deformation. Using, for example, the singularity analysis, it is found that the leading term of the Airy stress function x f°r symmetrically applied loadings on an isotropic medium is

Jan 1, 1968

By Morris Steinberg, John Wulff, Robert Kamm

IN powder metallurgy it has often been observed that shrinkage may occur in one direction and growth in another during sintering. Even in long-time sintering experiments the rate of shrinkage may be different in different parts of the compact. In the fabrication of some parts requiring a constant permeability it is even questionable in some cases whether pressing from one direction should be attempted. These observations require for their interpretation a more detailed study of green or pressed density than has heretofore been available. Usually average density measurements of the whole compact are made and in some cases carefully cut sections are measured. A different approach to the problem was first mentioned by Rakowski1 and also used by Balshin.2 Balshin's diagram is reproduced in Fig r and schematically shows the result of pressing three layers of metal powder with fine intervening layers of graphite. The retarding effect of the die walls and a qualitative example of the density distribution is evident. More quantitative information about the distribution of density within a cold-pressed powder compact would be useful in showing the variation in density in compacts as influenced by the type of powder, shape of die, lubrication during the process, and other variables. Furthermore, information about the cracking of cold-pressed compacts may be obtained from an analysis of the stress distribution within a powder compact, and some information about the stress distribution can be obtained in turn from the density and strain distributions. A more detailed report on some of the present experiments appears in reference 3. PRESENT INVESTIGATION In order to ascertain the density gradients in cold-pressed metal powders, a deformable lead grid within the powder was employed. After pressing in cylindrical dies the ejected compact was radiographed, giving a pattern of the deformed grid. From the radiograph density and deformation from point to point is readily measured. From the radiograph strain distribution and stress trajectories were also determined. The latter also permits the determination of the coefficient of friction at the die wall. This technique indicates that the densest part of a compact pressed from one side is at the top outer circumference and the least dense region at the bottom circumference near the stationary plunger. For some heights of compacts the density at the axis is such that the lower density is at the top rather than at the bottom. So irregular a density distribution is due primarily to die-wall friction. As the ratio of diameter to height of compact is increased the die walls play a correspond¬ingly smaller role. More uniform density

Jan 1, 1947

THE Rocky MountainClub brought into the East the spirit of the West; the impulse to build, to develop, to accept unquestion-ingly the comradeship and help of any straight shooter who had it in him to accom-plish things and a will to work. That this was the spirit of the Club was due to its leaders. It was their spirit and they attracted around them men of the same stamp. Among those who made the Club what it was no one had larger in-low fluence than William Boyce Thompson, the vice-president and chief of financial staff. It was characteristic of him that the same financial genius that was employed in building up Nevada Consolidated, In-spiration, Magma, Texas Gulf, and as director of the Metro-politan Life and the Federal Reserve Bank, was freely placed at the service of the Club. It was equally char- acteristic that the generosity that financed the Red Cross Mission to Russia inspired the use of the Club funds for Belgian and war relief. "W. B.," as he is known to his many friends, was born at Virginia City in Alder Gulch, Mont., on May 13, 1869. His father, William Thompson, born at Cobourg, Ont., had drifted into the old Northwest and, hearing at Yankton of the gold strike at Bannack, crossed the plains on the Oregon trail in the summer of 1863, arriv-ing in Alder Gulch at the inception of a mining boom that lasted several years, during which something like $60,000,000 in gold was yielded by the placer diggings. His mother was a daughter of Maj. James R. Boyce, Sr., from Logan County, Ky., who had served under General Sterling Price of the Confederate Army. Major Boyce's ancestors were early settlers of the Old Dominion, and his grandfather had seen military service in the war for American independence. Major Boyce's mother was a descendant of the Marshall and Smith families of Westmoreland County, Va. When Thompson was eleven years old, the family moved to Butte, then a silver camp. He attended the public schools of Butte, but desiring a better education, entered Phillips Exeter Academy and later the Colum-bia School of Mines. Returning West, for a year or two he ran the Boulder Chief mine near Basin, Mont., which earned him a sobriquet, "Boulder Thompson." While here, some old ore sacks, oil-soaked, introduced him to flotation. He was also the first to leach some of the ore dumps of Butte.

Jan 4, 1928

By F. V. Lenel

R. P. Seelig.*—Dr. Lenel is to be congratulated on his presentation of a particularly interesting paper describing the use of the powder metallurgy process for the production of magnetic pole pieces. The only thing that might be added is that we have been successful in producing pole . pieces with a narrow hysteresis curve by the use of considerably lower sintering temperatures than the ones used by Dr. Lenel. It is quite possible that this use of lowe- temperatures has considerably widened the field of commercial application for pole pieces made from metal powders. Development work is currently being done on an a.c. application of a sintered iron part. However, I am in full agreement with Dr. Lenel that if eddy currents are an important factor in the application, we cannot substitute sintered material for laminated sheet-metal structures. Mr. Peters' remarks concerning the limitations of machine parts were well taken. The emphasis of the limitations makes it easier to define clearly what we can do and-what the advantages are of machine parts made of metal powders. When I mention metal-powder machine parts, I mean those of relatively high density, although complete elimination of porosity is not possible at this time. The limitations of the field for this type of parts are largely economical. I believe that Mr. Langhammer has made that point very clear. The following questions are very often asked: How large a part can you make? How close can you hold the dimensions ? How fast can a part be produced? In a majority of the cases, it depends on the cost at which the part can be produced. A large variety of shapes and sizes of a number of materials can be formed. However, the main requirement in this field of endeavor is whether this can be done more economically by powder metallurgy than by other manufacturing methods. As a general indication, it may be stated that densities up to 95 per cent of that of rolled material can now be produced commercially in simpler parts. Tolerances of plus or minus 0.001 in. are common, but where special conditions justify, closer tolerances can be held; we are producing a part of which one dimension is held to 0.0003 inch. Finally, as far as maximum size is concerned, technically this would depend on the capacity of the press and furnace equipment available. Actually, we find that the economical limit of powder-metallurgy machine parts is approximately one pound. From there on, each individual case must he studied on its own merits.

Jan 1, 1945

By G. Richards Gwinn

GRAPHITE is one of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world's high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. TYPES of GRAPHITE USED IN CRUCIBLES Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1945

By R. Adair, W. R. Hudspeth, W. T. McDaniel

D. C. Ralston (U. S. Bureau of Mines, Washington, D. C.)—Flake mica can be beneficiated by a wider variety of methods than almost any known mineral. However, most of these methods are not recorded. It is therefore a pleasure to find a written record of another application of a new method of beneficiation. The fact that the Humphries spiral gives a concentrate containing the mica flake mixed with the slime and small grit has forced a further separation by screening, in which the finest of the flake will pass through. Fine flake has its uses and if mixed with slimes or clay is recoverable reliably only by flotation. This loss must be charged against the spiral. On the other hand, the new muscovite mica paper recently brought out by General Electric Co., can be made only with grit free flake larger than 50 mesh. It is of interest to learn from the authors whether the washing of the flake on a 50 mesh screen can take the grit content below 1 pct, to meet this new demand. Must another degritting process be used on the flake, like electrostatic treatment of the dried material? H. D. Snedden (The Humphreys Investment Co., Denver)—When recovering mica in the spiral, gangue particles coarser than 16 mesh can be rejected more readily when operating at a high pulp density (35 pct solids) or a low volume rate (—15 gpm). A launder screen as used by Lehigh Coal Co. has proved very satisfactory to partially dewater the mica concentrate and to reject any gangue slimes it may contain. Under certain conditions mica cleaning in the spiral can be improved by reagentizing the spiral feed, the object being to insure wetting of the gangue minerals and to agglomerate or prevent wetting of the mica particles. R. B. Adair (authors' reply)—The grit content of the mica recovered on Humphreys Spirals varies with the fineness of the launder screen used to clean the mica product. Normal practice has been the use of 80 mesh screen, which will produce a mica product of acceptable grit content for most purposes. By using a 50 mesh screen, and increasing the screen area per ton of feed, it is felt by the authors that a mica of 99 pct plus purity could be obtained. This statement would hold only in the case of mica feed which was well de-laminated, and free from "clay balls," (semikaclinized feldspar), which tends to follow the mica through the process.

Jan 1, 1952

Discussion of the paper of CHARLES H. MACDOWELL, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 103 to 114. GEORGE S. RICE, Pittsburgh, Pa.-I am especially interested in the mining side of this important question. In 1911, when in Europe investigating mining matters, giving special attention to subsidence clue to mining, for there is a very big problem of that kind, as many of you know, in the Pennsylvania anthracite region, I visited Stassfurt, which is one of the chief centers of potash mining, and which was pointed out as the place to see surface subsidence. We found the town much askewsome of the streets having sunk from 15 to 30 ft., leaving many ancient buildings pitching at various angles. One old church, 500 or 600 years old, has been sunk about 20 ft., cracking it badly. I understand that this condition came about because in early mining clays they were careless about leaving proper supports and used no filling or packing. The Stassfurt mines work along a buried anticline the sides of which pitch at 45° on the average. Through this careless mining they had a break of the hanging wall which let in water from the overlying marls and sands. The water rapidly dissolved the salts in the pillars, and spreading through the entire chain of mines, caused their complete loss, with serious trouble for the old city. They had to start new mines some distance away, and take care to prevent roof caves. The packing system is of interest. They were driving large rooms into the rock-salt foot wall and using the rock salt as dry filling. The application of hydraulic filling, using a saturated solution, was under contemplation at some plant nearby. Whether 6r not the plan was carried out I do not know. I was reminded of the plan by Mr. MacDowell's remarking on the use of a saturated salt solution in the core drilling. His reference to the apparent breakdown of the potash syndicate raises an interesting question. We have had the German system of syndicates pointed out as perhaps one means of solving our troubles in the soft-coal mining industry due to overproduction. It seems to have worked out admirably in the case of the Westphalian coal-mining syndicate and also in the syndicate of Upper Silesia; but apparently the syndicate plan did not work in the potash industry. .

Jan 5, 1915