Search Documents

By R. W. Gould, B. G. LeFevre, A. G. Guy

The resistivity anomaly known as the K state was studied in Ni-Mo alloys containing 10.5 and 14.0 at. pct Mo. Both these alloys exhibit a large K effect which depends on the mechanical and thermal treatment. On the basis of X-ray diffuse scattering studies which were correlated with resistivity measurements, it appears that the K state in dilute Ni-Mo alloys can be associated with changes in the degree of short-range order within the a phase. An interesting phenomenon that has received much attention in recent years is the K state. The K state is marked by anomalous changes in some of the physical properties of certain alloys without the occurrence of observable microscopic structural changes. One of the early pieces of work in this area was by Thomas' who studied alloys of Ni-Cr, Ni-Cu, Ni-Cu-Zn, Fe-A1, Fe-Si, and Ni-A1. Upon annealing specimens which had been previously cold-worked or quenched from an elevated temperature he found an anomalous increase in resistivity over a certain temperature range. He also found that specimens which had been appropriately annealed to develop the K state showed a decrease in resistivity upon subsequent cold working. These effects are opposite to those found in normal alloys. Although the resistivity anomaly has been rather arbitrarily taken as the "definition" of the K state, there are several other interesting effects which accompany the resistivity increase. In Ni-Cr alloys,2, 3 for example, it was found that the hardness increases with increasing resistivity. It was also found that specimens which have been treated to develop the K state can be cold-worked for as much as an 80 pct reduction of area without an increase in the hardness. In Fe-A1 and Fe-Si alloys4 the K state is accompanied by an increase in flow stress and by a lattice contraction. In Ni-A1 alloys,5 specimens which have been treated to develop the K state also show an increase in elastic modulus. In Ag-Pd alloys6 the increased resistivity observed on annealing a cold-worked specimen is accompanied by an increase in the thermoelectric power and an increase in the Hall coefficient. The explanations of the K state phenomena are varied and depend upon the particular alloy in question. Several theories have been advanced to explain the increased conductivity with cold work on the basis of changes in the electronic configuration of the alloy as a result of local lattice distortions.7"9 Most investigators, however, believe that some type of local order in the solid solution, either short-range order (SRO) or clustering, is responsible for this effect. Theories concerning the relationship between ordering and the K state have for the most part been speculative, since there is little direct X-ray evidence that can be correlated with the above property changes. Much of the previous work on the K state was done in the Ni-Cr system where the small difference in the X-ray atomic scattering factors of the components nickel and chromium makes it very difficult to use X-ray diffuse-scattering measurements to determine the role of local order. In the Ni-A1 system, however, Starke et al.10 succeeded in detecting a connection between local order and the K state. It was found that a small but measurable K effect correlated with increasing SRO in the nickel-rich a phase. The manner in which local order might increase the resistivity of K state alloys is not completely clear. Since most of the known K state alloys contain at least one transition element, significance has frequently been attached to the presence of an unfilled d shell. It has been suggested that during the formation of the K state the number of conduction electrons decreases as a result of the transfer of s electrons to the d shell where they are more tightly bound.1'11'12 Koster and Rocholl13 have proposed that SRO can cause an increase in resistivity for alloy systems in which the number and mobility of charge carriers are reduced when the percent solute is increased. According to this hypothesis, the local environment of a given solvent atom changes in the same manner with increasing percent solute as it does with an increasing degree of SRO; hence the change in physical properties should tend in the same direction. In this hypothesis, SRO is considered only in a statistical sense, and the increased resistivity of the K state is attributed to a change in the mean distribution of electrons and holes in the s and d states as a result of SRO. From the work of Chen and Nicholson on Ag-Pd alloys,6 it appears that the K state can occur in systems for which the d shell is completely filled. These investigators explained the increased resistivity by picturing the SRO as small domains of some form of long-range order (LRO). According to ~ibson,'~ the number of effective electrons can be reduced by the creation of a new Brillouin zone boundary near the Fermi surface of an alloy as a result of the changing crystallographic symmetry that accompanies the formation of a superlattice. This idea may be expressed in terms of the superzone concept.15 In the present work the role of local order in the formation of the K state in Ni-Mo alloys was investigated. The principal tools used in this study were X-ray diffuse scattering and electrical resistivity measurements; however, these data were supplemented by electron microscopic and field-ion microscopic data. The purpose of the work was to determine whether or not the K state in Ni-Mo alloys can indeed be attributed to the formation of SRO as has been proposed by previous investigators.

Jan 1, 1969

By L. D. Jaffe, F. W. Cotter, E. Cordon

The hardenability of titanium-base alloys was studied by metallographic examination and hardness survey of Jominy specimens end-quenched from the B range. Analyses of the data led to the equation log J = -0.57 + 0.25 @ct Fe + pct Mn + pct Mo) + 0.19 @ct Cr) +0.16 @ct V) + 0.03 @ct Zr). Here J is the distance, in sixteenths of an inch, from the quenched end of a Jominy hardenability specimen in the position of peak hardness, for material quenched from the B range. This equation fitted the experimental data with a standard deviation of approximately 0.29. The effects of the elements Al, Sn, W, Cu, Ni, B, C, N, 0, and H, and of pain size, were not statistically significant or not practically significant. A check against hardenability measurements in the literature showed agreement within the stated standard deviation. The equation should be useful in estimating hardenability of new or modified titanium alloys. HARDENABILITY in a titanium-base alloy is the ability of the alloy to retain the B structure on quenching. An alloy with high hardenability will retain the /3 structure even when cooled relatively slowly from a temperature at which B or P plus a is stable. A low hardenability material will retain P only if quenched extremely rapidly from the range of p or 0-plus-a stability, or will not retain it at all, at room temperature. High hardenability is desirable in titanium alloys to be heat-treated to high-strength levels. Its value is by no means limited to large section sizes. With high hardenability, a material can be solution-treated and cooled at a variety of rates, either to give high strength directly or, more generally, to give a soft ductile condition from which high strength can be obtained by subsequent aging. With low hardenability, high strength can be obtained, if at all, only by very rapid quenching, and there will generally be little increase in hardness on subsequent aging; an alloy of this type is limited in its applicability. On the other hand, alloys of very low hardenability have some advantages in weldability; essentially, they are always in the annealed condition, after welding as well as before. For commercial alloys, hardenability data are usually available, in the form either of property data after cooling from the solution temperature at various rates, with or without subsequent aging, or of results of a standard hardenability test, such as that originally developed for steels by Jominy and Boegehold.' When modifications of an available alloy are considered, or preparation of new alloy compositions, it would be Very convenient to be able to estimate the hardenability of the new material without having to make and test it. A method of estimating hardenability of titanium alloys from their composition was suggested by one of the authors some time ago, on a preliminary basis, utilizing scattered data found in the literature.' It seemed worthwhile to carry out a systematic experimental study of the effect of composition upon hardenability. EXPERIMENTAL PROCEDURE Approximately fifty heats of various compositions, weighing 8 to 10 Ib apiece, were melted in a small inert-gas tungsten-arc furnace with water-cooled copper walls. The starting material was 110 Brine11 titanium sponge, with high-purity metals added for alloying. Each heat was bottom-poured under vacuum through a molybdenum burnout strip into a cold graphite mold, to form an ingot approximately 4-1/2 by 3-1/2 by 3 in.* From each ingot were cut *The material was melted and cast by Pitman-Dunn Laboratory, Frankford Arsenal, to whom the authors must express their thanks. two pieces 4-1/2 by 1-1/2 by 1-1/2 in. These were forged, at temperatures adjusted to the composition, into 1-1/4-in. rounds, from which standard 1-in.-diam hardenability specimens3 were machined. A number of small samples were also prepared from forged materials of each heat, annealed, quenched from various temperatures, and examined metallographically. The P-transus temperature was determined by observation of the degree of resolution of primary a in these pieces. samples for chemical analyses were also taken from the forgings. One hardenability specimen of each heat was solution-treated for 1 hr approximately 50°F above the measured transus temperature, and the other for 1 hr approximately 250°F above the transus. (An additional hour was allowed for the specimens to reach furnace temperature.) These are not necessarily the temperatures that would be selected for

Jan 1, 1964

By R. F. Hehemann, R. H. Goodenow

Thermal arrest, hot-stage microscopy, and transtnission electron microscopy techniques have been employed to study the transformations in low-carbon iron and Fe-9 pct Ni alloys. In continuous cooling experiments, each alloy transforms at an essentially constant temperature for cooling rates below the critical rate required for martensite formation. However, high-tenzperature transformation in pure iron takes place by a different mechanism than that in the 9 pct Ni alloys. Pure iron exhibits an equi-a a structure with a low and random dislocation density while the 9 pct Ni alloy exhibits a cell or lathlike substructure analogous to that of low-carbon martensite. This same substructure characterizes upper bainite in higher-carbon inaterials. UNTIL relatively recently, diffusionless transformations have been considered to take place by the same mechanism and have been termed mar-tensitic transformations.l-3 The most characteristic feature2 of this mode of transformation is the shape change produced by a shear deformation and growth of the product phase frequently occurs at an extremely high velocity approaching that of an elastic wave.4'5 A different mechanism of diffusionless transformation was recognized first in Cu-Ga and other copper-base alloys.6,7 From the absence of surface tilting in these alloys, it has been concluded that transformation is not accomplished by the cooperative shear displacements that occur in mar-tensitic reactions. Transformation presumably takes place by the rapid movement of an incoherent interface which is capable of propagating across parent grain boundaries. Although the transformation is diffusionless in the macroscopic sense, advancement of these interfaces is accomplished by an atom by atom rearrangement. Transformations of this type therefore require thermal activation and are generally operative only at high temperature. Although requiring short-range diffusion at the interface, propagation still occurs so rapidly that the reaction cannot be suppressed with normal cooling rates.7 The resulting microstructures exhibit large, irregular-shaped regions of the product phase, which are essentially free of crystallographic features. Consequently, these reactions have been termed massive transformations. Transformation by the massive mechanism has been reported to occur in ferrous systems involving pure iron and binary alloys of iron with nickel, chromium, and silicon by Gilbert and owen.' The Fe-Ni system is of special interest in that the massive transformation was observed in alloys with less than 15 pct Ni while alloys having more than about 28 pct Ni transformed by the conventional mar-tensitic mechanism. By employing cooling rates substantially higher than those used by Gilbert and Owen, Swanson and Parr have been able to suppress the massive transformation in alloys with 0 to 10 pct Ni9 and produce martensite as revealed by surface relief. The massive transformation in the alloys having less than 15 pct Ni was identified by the lack of surface relief and an irregular rather than clearly acicular microstructure.' Speich and Swann, using thin-foil electron microscopy, identified three distinctly different structures10 in quenched binary Fe-Ni alloys. From 0 to 4 pct Ni the structure consisted of blocky grains of a with a low and random dislocation density. Alloys with 4 to 25 pct Ni exhibited a cell structure with a high dislocation density; and at greater than 25 pct Ni the structure consisted of internally twinned plates. The structural change at approximately 4 pct Ni suggests that alloys with low nickel content transform by a different mechanism than those with intermediate nickel contents and the transition from the cellular to the internally twinned structures at approximately 25 pct Ni is analogous to the transition from needles to internally twinned plates that occurs over a narrow range of carbon contents in Fe-C martensites.11,12 Conventional bainitic and martensitic modes of austenite decomposition operate in ternary Fe-C-Ni alloys having less than 10 pct Ni. This investigation was conducted in order to explore the conditions under which the massive, bainitic, and martensitic transformations occur and the relationships between these modes of decomposition.

Jan 1, 1965

By Masatsugu Taniguchi

Onoda Cement Co., Tsukumi is one of the largest limestone producer in Japan. From mines called Suisho and Ganji, it supplies limestone for cement plant, lime manufacture, iron and steel industries and for many purposes. The Suisho mine is highly productive, though it's operations are governed by the utmost regard for its impact on the surrounding environment. However, it became difficult to meet additional expanding demand and to assure continuity of high rate production. Present production rate 1s 6 million tons per year. The Ganji mine, some 2 km south west of the Suisho mine, began first-stage development In mid- 1973 and in january I976 started production. The capacity of major facilities is 9 million tons per year. Full production is predicted in 1979. Mining and milling methods of these mines under strict environmental considerations are discussed.

Jan 1, 1976

By A. M. Gaudin

The study that is presented here was undertaken in order to condense information concerning comminution, and covering a great variety of conditions, into one or several rules which would be of use in the development of a systematic theory as well as in many directly practical ways. As the result of this work, the following conclusions appear justified: 1. Rocks may be classified, from the point of view of comminution, into two general classes which are (a) structurally homogeneous, and (b) structurally heterogenous. Structurally homogeneous rocks are those in which fracture takes place through grains and grain boundaries alike; heterogeneous rocks are those in which fracture passes in preference through grain boundaries. 2. If a sized product composed of structurally homogeneous rock grains is crushed, a product results in which the relation between the percentage weight of grains of various sizes and these sizes themselves follows a definite law. This is not true of structurally heterogeneous rocks. 3. Ball milling with structurally homogeneous rocks, and under certain conditions, presents exceptions to this rule. 4. In ball milling with structurally homogeneous rocks, there exists a critical ratio of size of feed to size of balls, above which the machine operates essentially by surface wear, and below which it operates essentially by breaking across the body of the particle. 5. In ball milling, with structurally homogeneous rocks, and when the size of feed grains exceeds the critical size, the particles worn off are of a substantially definite size which depends upon the ball size. 6. In the case of a typical heterogeneous rock, such as Manhattan schist, particles are crushed in such a way that there is a greater proportion of grains of the size that is the average grain-size of the rock than there would be in that range of size with a structurally homogeneous rock. This has been found to be true with all the crushers tested. 7. Different methods of crushing produce grains of different shapes. 8. The importance of sizing the — 200-mesh portion of a crushed product, in crushing-efficiency investigations, has been greatly under-

Jan 1, 1926

By N. H. van Lingen

A laboratory stud], has been made to determine what factors affect the penetration rate of roller bits, diamond bits and drag bits in rock drilling with clay /water muds. The rather simple relations that exist when pressures in and around the borehole are equal become more conzplicated when under down-hole conditions the penetration rate is hampered by the existence of a pressure differential between the mud at the hole bottom and the pore liquid at cutting depth. Expressions that have been derived for both the penetration rate and the magnitude of the pressure differential in permeable rock together fully account for operating, rock, mud and bit variables. In impermeable rock a similar pressure differential is caused by the bit action itself. In all cases, the pressure difierential and the reduction in penetration rate increase with the effectiveness of the plastering at the bottom of the hole by mud particles. Where bits are employed whose action is largely that of crushing, however, the plastering may become even more effective owing to the addition of rock particles rubbed into the pores of the rock. With roller bits, a plastically hehaving layer may be formed, which causes a further reduction in penetration. In the case of bits whose action is chiefly scraping, moreover, penetration may be arrested by the bit's becoming balled-up. The various adverse effects are reduced by thorough scavenging of the hole bottom. This paper shows how with jet bits the efficiency of such scavenging may he improved by suitable choice of the position of the nozzles. INTRODUCTION The reduction in a bit's penetration rate with increasing depth of hole has been the subject of many investigations. Various investigators ',' have independently reached the conclusion that this reduction occurs not so much because the rock-breaking process becomes more difficult as it does because the lifting of the rock fragments is impaired by a fluid pressure differential holding the fragments down. When such a pressure differential can be avoided, as in air drilling and to a smaller extent in water drilling, penetration rates remain high. Although the range of applicability of these techniques is being extended, most oil wells still have to be drilled with mud. In this paper we present the results of laboratory experiments carried out to determine what factors govern the hold down effect encountered in mud drilling. In the course of this investigation, the well known importance of bottom scavenging came more and more into prominence. Not only may it reduce the magnitude of the hold-down forces, but also it appeared to be a means of preventing the accumulation of a plastic mass of cuttings and mud on the hole bottom and bit which may cause penetration to cease almost completely. So that the effects of fluid pressures may be more readily understood, the factors that govern penetration rate in the absence of these pressures will first be discussed. The effect of down-hole pressures will then be assessed for the case of permeable rock where fluid pressures are well defined, and it will be demonstrated how rock strengthening due to confining can be accounted for. Subsequently, fluid pressures in less-permeable rock will be examined; we will show that in impermeable rock it is the bit action that governs fluid-pressure distribution and hold-down. In the case of poor scavenging and/or high bit load. cutting cake manifests itself. The effect, like various others. appears to depend on the type of bit used. From the very beginning, therefore, we shall base our discussion on the three main types of bits used in rotary oil-well drilling— roller bits, diamond bits and drag bits. Since space is limited, it will be impossible to make more than a passing reference to many aspects of the problem. Moreover. certain relations that are not of primary irnportance to our argument will unavoidably have to be stated in a somewhat dogmatic fashion, and the experimental data on which these are based necessarily must be omitted. EQUIPMENT The drilling experiments were performed on three machines, of which one has been designed for the realistic simulation of down-hole pressure conditions. HIGH-PRESSURES MACHINE In this machine (diagramed in Fig. 1) the mud, pore and confining pressures can all be adjusted independently. The foil-covered rock sample contained in the inner pressure vessel is confined by oil that is pressurized by means of a hand pump. The pore space of the watersaturated sample is connected to an arrangement which keeps the pressure in the pore space constant regardless of the rate of filtrate flow through the sample.

By Bradley Stoughton, M. Miyake

The importance of magnesium alloys as engineering materials has increased rapidly in the past few years. The most important properties of magnesium alloys are their lightness and strength, which result in their extensive use in aircraft and automobile construction. Recent progress in the metallurgy of magneaium seems to offer hope of the production of the pure metal at a reasonable cost. The use of magnesium would doubtless increase greatly if it could be produced at a cost comparable with that of aluminum. A preliminary survey of the magnesium-base alloys shows that the most promising from a practical standpoint are magnesium-aluminum and magnesium-zinc as binary alloys, and magnesium-zinc-aluminum as ternary alloys. The research reported in this paper is a preliminary study of binary magnesium-aluminum and magnesium-zinc alloys, as an introduction to a series of further investigations. Magnesium-aluminum System The magnesium-aluminum system was first studied by Boudouard,1 who merely determined the liquidus. An accepted constitutional diagram was given by Grube,2 who found a compound A13Mg4 (melting point = 462.7" C.) and two eutectics at 35 per cent. magnesium (451.6° C.) and at 68 per cent. magnesium (440" C.) Between the first eutectic and the compound a solid solution exists. This diagram was checked or supplemented by Pécheux,3 Broniewski,4 Eger,5 Schirmeister,6 Voge17

Jan 1, 1926

By AIME AIME

SHORTLY after he started his professional career, the subject of this sketch acquired the sobriquet "Moose" Allen. At the time he was engaged in geological exploration it1 the Canadian wilds. The nickname was given .him because of the wide, straight trail that he broke with unusual speed when going through the bush. Like a moose he was strong, energetic, and determined. To a considerable degree, Rolland Craten Allen today displays the same characteristics in larger affairs-business, civic, and professional. It is his habit to study a problem thoroughly, to decide u11on the best course of action, and then to pursue that course with vigor and

Jan 1, 1936

By AIME AIME

THIS year the Petroleum Division holds its fall meeting at Houston, Texas, Oct. 2 and 3, with head- quarters at the Lamar Hotel. Technical sessions will be held in the morning and afternoon of both days. A smoker on Friday afternoon will afford an opportunity to get together socially. Saturday evening is left free for private parties to the beach at Galveston, where a wide variety of entertainment is available. On Oct. 4 there will be an excursion to Sugarland oil field, with luncheon at Boling and a visit to Boling sulfur mine and plant in the afternoon. There are nine technical papers on the program for Friday. Saturday morning will be devoted to oil production control and it is planned to make the discussion more

Jan 1, 1931

By R. L. Templin

The increasing use of aluminum and its alloys in commercial fields tias demanded a better understanding of their machining properties. This fact is exemplified by problems that have arisen in the automotive and airplane industries, but many in other fields might be cited. As pure alunlinum and its alloys in their various commercial conditions show appreciable differences in their machining properties, it is not surprising that quite divergent solutions have been offered for the machining problems encountered. However, if the fundamental requirements of the most suitable cutting tools for these metals are understood, these machining problems lend themselves more readily to satisfactory solutions. Since the machining of free cutting brass and mild steel is understood by most persons accustomed to working these metals, it may serve our purpose better to first make a general comparison of the tools more commonly used in machining these metals with the tools most suitable for machining aluminum, then proceed to a more specific discussion of the individual tools. Comparison oF Cutting Tools Cutting tools commonly used for machining free cutting brass usually have little, if any, top and side rake; they are ground on a medium to coarse abrasive wheel and used without any cutting compound or with a cutting compound that has a paraffin base. Those ordinarily used for steel have some top and side rake, are usually ground on a medium to fine abrasive wheel, and are often used with soluble-oil cutting compounds. The proper tools for aluminum and its alloys should have appreciably more side and top rake than the tools for cutting steel; should have very keen edges obtained by grinding with fine or very fine abrasive wheels supplemented in many cases by hand stoning with an oil-stone; and should be used with suitable cutting compounds whenever possible. In many cases, tools suitable for machining aluminum and its alloys are not appreciably different from tools commonly used for cutting hardwoods. The front clearance of a tool most suitable for machining aluminum and its alloys should be about 6°, the top rake from 30" to 50°, making the total angle of the cutting edge of the tool from 35' to 55". A side

By Dr. O’Neil Thomas J., Donald W. Gentry

"Who is the man who views the mines and promptly turns them down? Who is the one that thinks this is the short cut to renown? Who is it gives the bum advice to the innocent financier? The knowledge-feigning, theory- straining mining engineer." -Anonymous INTRODUCTION Taxes levied against mining properties and operations are a critical cost in the economic evaluation of mining investments. Indeed, taxes represent a substantial cost of doing business in the minerals industry and often have a significant impact on corporate investment decisions. A good example was the postponement of mineral development in the state of Wisconsin, primarily because of what was perceived to be excessive taxes imposed by that state. In many respects mining investments are no different from other industrial investments. Astute taxing authorities should recognize that geologic endowment is a necessary but clearly not a sufficient condition for mineral investments. The fact that a mineral deposit exists does not necessarily mean that it will ultimately be developed-a point that many taxing authorities fail to recognize. While it is true that ore deposits are not mobile in the sense that they cannot be physically moved to a district having more favorable taxes, corporate investment capital certainly is mobile and flows to ventures which maximize wealth to the firm. In short, higher taxes reduce project yields and tend to drive investment capital elsewhere. The appropriate type and level of taxation imposed upon the mining industry continues to be a very controversial and emotion-charged topic. Mining activities have been taxed at various levels over the years due to widely differing taxation philosophies. Location has also influenced taxation policies, as evidenced by the diversity of tax laws and assessment procedures applied to mineral deposits by the various states. Indeed, mineral taxation varies from state to state, from county to county, and from one mineral commodity to another. Whether or not a given tax is appropriate for a specific mineral deposit, or even an industry, is a difficult problem to assess. First, the type or kind of tax which should be imposed must be considered. Second, it is most important to define a fair and unambiguous base against which to levy the tax. Finally, one must consider the tax rate to be applied to this base. It is the combination of these two components

Jan 1, 1984

By P. J. Carroll, H. Colijn

Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. Feeder load, material properties, feed rate, physical layout, and environment as well as first cost determine the selection of feeder type. This paper provides a new method of calculating feeder loads with some experimental data as verification. General design criteria for belt and apron feeder, rotary table and plow feeders are discussed and a special section is devoted to vibratory feeders. Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. During the past few years various papers have been written and presented on feeders and their application.1-9 This paper will be confined to some specific bin-feeder design criteria such as feeder load and power requirements. Special attention is given to the basic design criteria for vibratory feeders. HOPPER AND BIN DESIGN Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. A lot of effort has been devoted in the past decade to the development of functional design criteria for hoppers and bins.1,10 The integrated concept of bin and feeder design requires quantitative analysis of the bulk material characteristics before the design and the selection of components can be attempted. The design of a feeder system must begin with the proper dimensioning of the hopper outlet to prevent arching or ratholing. The hopper opening should be large enough to allow passage of the bulk solid at the required maximum discharge rate." A feeder can only throttle the flow. FEEDER LOAD DETERMINATION Over the past ten years, there have been various attempts to determine the exact load or pressure on feeders mounted directly under hopper openings. Many designers, however, still consider this pressure equal to the hydrostatic head of material above the opening, and because such pressure would be very

Jan 1, 1969

By LE B. GRAY

ALL meeting of the Chemical Section, National Safety Council, in Rochester, N. Y., put his hand on at least ten salient points that apply to safety in nearly any laboratory ; these are as follows : 1. Impress your laboratory worker at the start that he is dealing with powerful and dangerous-forces and that every experimental set-up must be studied from the stand- point of its fiber, electrical, explosive, and health hazards.

Jan 1, 1929

By Eugene S. Meieran

The effects of methods of crystal growing, wafer sawing, polishing, routine handling, diffusion, and epitaxial growth on the defects in GaAs are reviewed and studied using reflection and transmission X-ray topographic techniques. In general, it was found that boat-grown crystals exhibited fewer defects than Czochralski crystals, although all crystals showed large numbers of precipitates visible when examined in the electron microscope. Mechanical surface treatments such as sawing and mechanical polishing introduce damage to a depth of about 5 µ, most of which can be removed by suitable chemical or chem-mechanical polishing. In addition, defects can be introduced through routine handling of wafers, for example with metallic tweezers. These defects can be quite severe, and have been observed 20 µ below the wafer surface. Defects can also be introduced through diffusion and epitaxial growth. These defects, which include precipitates, growth pyramids, stacking faults, dislocations, and so forth, can be detrimental to device fabrication. It is shown that wafers or films which appear defect-free optically can contain defects visible in the X-ray topographs. WHILE the use of GaAs in the semiconductor industry has increased very rapidly in the last few years, due mainly to the recent development of many important GaAs devices,1,2 the major limit to the production of commercial quantities of many GaAs devices remains a severe lack of suitable materials technology. This lack is apparent in two critical areas. First, production quantities of high-quality GaAs crystals, reproducibly doped and precipitate-free, simply are not available commercially, although some reasonable quality material is available on a limited first-come, first-serve basis. Second, in comparison to silicon technology, little is known about the effects of processing variables on the defects either present in as-grown GaAs or introduced through processing and handling of wafers. These areas are now receiving some attention from semiconductor device manufacturers, who are studying defects in GaAs in order to better understand how either to prevent their occurrence or to cope with their existence. Most investigations of the defects in GaAs have been made by optical microscopy3-5 or transmission electron microscopy techniques.'-' Recently, however, the imaging techniques of X-ray topography, electron mi-croprobe analysis, and scanning electron microscopy are being applied to the study of GaAs.9-14 In the case of X-ray topography, a one-to-one image is obtained that must be photographically enlarged. In compensa- tion, the defects within entire wafers may be imaged by simple scanning (Lang technique15) if the wafer is reasonably perfect, or by using the scan oscillation technique developed by Schwuttke16 if the wafer is warped or distorted. The purpose of this paper is to both review and extend the general application of X-ray topographic techniques to GaAs. Emphasis will be placed on the effects of growth and process variables on the quality and perfection of both bulk and epitaxial GaAs. Reference to optical or electron microscopy results will be made when useful. Since the effects on defects of a wide variety of processing variables such as crystal growing, sawing, polishing, diffusion, and epitaxial growth will be somewhat superficially reviewed, a fairly extensive bibliography of the most important recent results in these areas is included. However, for completeness, important defects will be illustrated here, although such defects have been previously shown by others. While this paper is concerned with defects rather than with the physics of X-ray scattering, the mechanisms of contrast formation in the topographs will of necessity be briefly mentioned. EXPERIMENTAL GaAs crystals, both boat-grown18 and Czochralski-grown,'8 containing a variety of dopants of various concentrations, were purchased from outside vendors. Wafers were sliced from the crystals using a Hamco ID saw and were mechanically polished using 1 µ diamond paste. Chem-mechanical polishing was done in bromine-methanol as described by Sullivan and Kolb.18 Chemical polishing was done using a modified sulfuric-peroxide solution, 11 parts H2SO4, 1 part 30 pct H2O2, 1 part DI water.5 Zinc diffusion was carried out in a closed tube, using a 10 pct Zn-In source at 825°C for 1 hr. Oxide masking techniques were used to select the area to be diffused. Epitaxial wafers were either purchased or prepared here. All epitaxial runs prepared here were carried out using a Ga-GaAs-AsC13 source in a closed tube at a substrate temperature of 750°C. Wafers were chem-mechanically polished and gas-etched prior to deposition. The X-ray topographs were taken on a Krystallos Lang camera, operating in the transmission scanning geometry (Lang technique15) or in the reflection scanning geometry (modified Berg-Barrett technique20,21). MoKa, radiation was used for all transmission topographs using a Jarrell-Ash 100-µ spot focus. CuKal radiation was used for all reflection topographs using a General Electric CA-7 1-mm spot focus X- ray tube. Topographs were printed from an intermediate contrast inversion film, so the contrast shown in all figures here is the same as that of the original 50-µ-thick emulsion L4 Iiford nuclear plate used to record the topograph.

Jan 1, 1969

By Frank Woolley, John F. Elliott

The high-temperatzrre solulion calorimeter has been modified and an extension dynamic analysis of i/s transient behavior has provided an improved basis for interpretation of the experimental data. The partial molar heats of mixing, Him, of aluminum, copper, and silicon in the corresponding binary liquid-iron alloys haz,e been measured directly at 1600°C. The resulls in kcal per g-alom are: THE high-temperature1,2 solution calorimeter was planned and designed to obtain directly the partial molar heat of solution of solute elements in a variety of liquid metals that might serve as solvents. Results obtained in the temperature range of 1000° to 1200°C were described in the two earlier publications. However, a long-term goal in the program has been to obtain measurements at 1600°C of the heats of solution of elements in liquid iron. Hence, subsequent to the work last reported,2 and based on the experience of the first two studies, the calorimeter system has been modified and operated at 1600°C to obtain measurements on the Fe-Si, Fe-A1, and Fe-Cu systems. This paper reports the results of the work. THE MODIFIED SYSTEM It was clear from the earlier results that the most precise measurements can be obtained with the high-temperature solution calorimeter when the solution time is less than approximately 30 sec. This can be achieved only when the bath temperature, Tb, is above the melting (liquidus) temperature of the solute material being dropped. A second point of importance is that the refractories used earlier liberated considerable water so that, although the oxygen potential of the atmosphere in the system was satisfactory for work with nickel and copper, it was too high for work with iron, silicon, and so forth. Third, for work at 1550" to 1650°C, an improved temperature-sensing unit is needed. The modified calorimeter in its latest form is shown schematically in Fig. 1. The refractory brick and the Kanthal-Super heating elements which formed the furnace for heating the solute addition have been replaced by a smaller resistance-heated tube furnace which is insulated with bubble-grain alumina. A more elaborate gas purification system was installed to maintain a satisfactorily low oxygen potential in the atmosphere of the calorinieter chamber and of the solute addition furnace. As was the case in the earlier work, at the beginning of a run the calorimeter chamber is evacuated and then filled with purified argon so that a total pressure slightly in excess of 1 atm is maintained during the run. When either of the furnaces within the enclosure attains a red heat, 6 pct H2 is added to the atmosphere. Throughout the run, gas from the calorimeter is circulated through a de-oxidation system at the rate of approximately 5 standard liters per min; the changeover time for the gas within the calorimeter enclosure is approximately 1 hr. The essential stages of the deoxidation system are: a copper furnace at 600°C, a drying tube of anhydrite, and a titanium furnace at 800°C. The oxygen potential of the gas stream in the purification system can be monitored at several points by a stabilized zirconia oxygen cell. This cell is invaluable in detecting the development of leaks in the container vessel and the gas circulating system. The installation of the solute-addition furnace allowed either of two types of temperature-sensing units to be mounted on a water-cooled probe. The first was a small optical device using a silicon diode that was

Jan 1, 1968

By N. Plint, E. T. Pinkney

Copper segregation developments within the Anglo American Group are described with particular reference to the work of the TORCO Project Team. Some radical differences have been adopted in the mechan-ical approach as compared with methods used by previous workers. Most important among these are the following: (1) The heating unit is a fluidized-bed roaster. (2) A moving bed segregation chamber is used in which a packed bed of heated ore, to which reagents have been added, moves slowly downwards under gravity and is discharged at a controlled rate by means of a suitable valve mechanism. (3) The quantities of reagents used (sodium chloride and some form of carbon) are only a small fraction of those recommended by other investigators. (4) Retention times of only 2 min have been satisfactory for the complete segregation of many types of ore. Project TORCO is the code name given by Anglo American Corp. of South Africa, Ltd., to the investigation undertaken in Zambia to develop a plant capable of treating large tonnages of refractory copper-bearing ores by the segregation process. The process has now been under investigation for six years (1960-66) and during that period work has progressed from bench-scale laboratory tests through small-scale pilot-plant work to a 500-tpd commercial pilot unit. Test work has been carried out mainly on the ores of the Zambian Copperbelt and results have been encouraging. Recoveries on the order of 90% have been obtained on all Copperbelt ores tested with high concentrate grades. PRELIMINARY INVESTIGATION Laboratory scale segregation test work on Nchanga banded sandstone ore and oxidized ore from Kansan-shi was originally conducted by Professor Maurice Rey. SociCtC Miniere et Mktallurgique de Pefiarroya, in 1957. Both ores responded favorably to the process. In November, 1960, the consulting engineers of Anglo American Corp. of South Africa, Ltd., initiated preliminary investigations on the application of the segregation process to Copperbelt ores. In early laboratory work, samples were heated in a closed, externally heated tube furnace for one hour at temperatures ranging from 800 to 830°C. The free moisture content of the ore feed was 4% and reagent additions were 0.5% salt and 1.0% coal. Both salt and coal were pre-crushed to -48 mesh Tyler.* All samples except an ore from the Bancroft mine responded well to the process and recoveries of over 90% were obtained. The presence of dolomite was responsible for the relatively poor recoveries from the Bancroft ore, as tests on one of the other ores with additions of calcite or dolomite confirmed. Recoveries dropped from 94 to 45% Grades of all the rougher flotation concentrates produced were low at 10-15% copper. The laboratory investigation was then followed up on a pilot-plant scale. An attempt was made to carry out the segregation process in a coal-fired 5-ft-diam fluidized-bed roaster. The feed consisted of a banded sandstone from Nchanga to which 0.5% sodium chloride had been added. Reducing conditions were maintained in the roaster by the addition of coal in excess of that required for heating the feed. The excess coal and added salt constituted the segregation reagents and the temperature of the bed was held at approximately 750°C. Recoveries of copper and grades of concentrates were low. The reasons for lack of success were: (1) The reaction is a gaseous one and a fluidized-bed roaster is therefore unsuitable as a segregation unit. (2) Coal in excess of that required for heating was introduced into the fluidized bed and under these conditions some of the copper would be reduced in situ. The term "reduced in situ" is used here to describe any copper mineral reduced to the metallic state in its original site within the ore particles. If this copper is to be recovered by subsequent froth flotation it must first be liberated from the gangue by grinding or some other method which, in practice, is usually not feasible on ores of this type.

Jan 1, 1969

By AIME AIME

In taking account of stock, on the occasion of the recent removal of the office of the Institute, it was found that pamphlet copies of the papers named in the list given below were on hand, in excess of the average number deemed adequate for future casual demand. Special reduced rates will be made for these surplus copies to members applying promptly. "First come; first Served." Author. Title. Ref. No. ASHBURNER, C. A. " Petroleum and Natural Gas in New York State." 273 MARTENS, A. "The Microstructure of Ingot¬ Iron and Cast Ingots." 626

Jan 1, 1907

[University of Alaska College, Alaska Mining Society TOM CHRISTENSON, President MARY ANN KISER, Secretary H. G. WILCOX, Faculty Sponsor WM. FACKLER, Counselor University of California Berkeley, California Mining Association JOHN W. COOK, President LORETTA A. RICHTER, Secretary W. S. WEEKS, Faculty Sponsor]

Jan 1, 1946

By S. K. Tarby, W. O. Philbrook

The rate of FeO and MnO reduction from silicate and aluminate slags by carbon-saturated iron is dependent on both slag composition and temperature. Owing to variable stirring rules during- the course of reaction, the reduction processes occur in two stages in stationary graphite crucibles. In the first stage the slirring caused by CO evolution results in forced convection conditions in the slag. As the boiling action subsides during reduction, the flow conditions within the system become those defined by natural convection. Analysis of the data by an unsteady-state penetration model indicates that the rate of reduction is controlled by the rate of cocur-rent flow of' cations and anions from the bulk slag to the interface during both stages of reduction. The hearth reactions of the blast furnace have been extensively investigated from the viewpoint of equilibrium by deductions from controlled laboratory experiments. However, the literature contains relatively few studies that have been directed toward the area of slag-metal reaction kinetics, and the majority of these have been concerned with the rate and mechanism of sulfur transfer between iron and slag. More recently, attention has turned to the kinetic factors in the reduction of oxides from liquid slags. One of the first investigations in this field was conducted by Dancy1 on the reduction of pure liquid FeO and pure liquid Fe3O4 by carbon-saturated iron. The integrated form of the rate equation indicated that the reduction of FeO was of the first order up to 80 pct reduction. Over the initial 30 pct of reduction, the magnetite reaction was also interpreted as a first-order process. The rates of reaction were extremely rapid as indicated by a 30 pct reduction of the liquid magnetite in a time interval of about 1 to 2 sec. Phil-brook and irkbbride' studied the reduction of FeO from a lime-alumina-silica slag by carbon-saturated iron and solid graphite in stationary crucible assemblies. With the use of the differential form of the rate equation, the rate of the reduction reaction was found to be proportional to the second power of the concentration of the reactant FeO for both the slag-metal and slag-graphite reactions. These authors presented a number of comments in an effort to explain the difference between the molecularity of the above reaction and the observed second-order relation. One such argument, recently extended by Wagner,3 was that the rate-limiting step may well be one of transport control. A complete discussion of the proposed mass-transport control mechanism of this reduction reaction will be presented in a later section of this paper. Kinetic studies of the reduction of other oxide species, namely chromous oxide, titania, and silica, have also been reported. McCoy and philbrook4 used rotating crucible assemblies to investigate chromium reduction from Ca0-SiO2-A12O3 slags. First-order kinetic law was obeyed for the slag-metal reduction reaction as determined by the integration method of data analysis. Due to scatter of the data, any dependence of the rate constant on temperature or slag composition was obscured. Concentration-time data for the reduction of titania from blast-furnace type slags under reducing conditions were obtained by Delve, Meyer, and Lander.' The data were too few, however, for a formal kinetic interpretation. Kinetic data for the very slow reaction of silica reduction have been observed by McCoy and Philbrook6 and Fulton and chipman.7 The former experimenters found the reaction-rate constant for silica reduction by carbon-saturated iron to be 20 to 60 times less than the rate constant for chromium reduction. In their work on the reduction of SiO2 in mechanically stirred systems, Fulton and Chipman also found small values for the specific reaction rate and derived a high value for the energy of activation for the reaction. In both of these investigations, the reduction process was assumed to follow first-order behavior. schuhmann8 proposed that the rate-limiting step in this reaction is the diffusion of oxygen from the interface through a boundary-layer film to the bulk metal phase, and Rawling and Elliott9 have reported experimental confirmation of this hypothesis for temperatures below 1600°C. Turkdogan et a1.10 have also concluded that the rate of reduction of silica is a slow process and controlled by the diffusion of oxygen in the metal, but only in the absence of carbon monoxide bubbles at the slag-metal interface. In the presence of bubbles, achieved either by injecting carbon monoxide at the slag-metal interface or by blowing it through the metal and slag, these investigators found a rather rapid reduction of silica which appeared to be controlled by an interfacial reaction involving the de-sorption of silicate ions from the slag-metal interface to the metal phase as silicon and oxygen atoms. In view of the unresolved nature of the kinetics of FeO reduction and the lack of kinetic data for the manganese reaction,

Jan 1, 1968

By W. S. Morris

THE East Texas oil field is the largest in the United States and perhaps the largest 'in the world ; likewise, it is one of the most interesting. The East Texas oil field is a water-drive field. Small amounts of salt water were produced from wells on the western side of the field from the bt-ginning of the development. By the end of 1933 (the field having been discovered in September 1930) water production had reached 9000 barrels per day. By the end of 1936, approximately 2000 wells were producing about 45,000 barrels of water per day, and the problem of salt water disposal attracted the serious attention of the operators. Salt water production in the field has steadily increased and today approximately 450,000 barrels of water per day is produced while the oil production averages about 375,000 barrels. The disposal of this salt water has therefore become one of the major operating problems. Various methods of salt water disposal have been tried in the East Texas field. Evaporation in open pits proved

Jan 1, 1944