Search Documents

By W. A. Ver Wiebe

It is becoming increasingly apparent that the State of Kansas contains one of the largest reserve areas for oil exploration in the United States. During the year 1936 no less than 54 new oil pools were discovered by drilling. In addition, seven gas pools were found, which may develop into oil pools when deeper horizons are tested. Several old pools increased their reserves when production was found in lower strata. The data presented in Table 2 indicate that nearly 2000 wells were drilled in the state during 1936. Of these more than 1214 found commercial quantities of oil and at least 61 found marketable quantities of gas. The data are conservative because complete results on drilling are not available for the eastern part of the state. Ellis, Rice and Russell Counties share honors with a total of 10 new pools in each. Barton County is prominent with six pools; while those counties claiming fewer new pools are Clark, Ellsworth, Harvey, McPherson, Ness, Pawnee, Rooks, Stafford and Trego. Important additions to our gas reserves were found in Finney and Haskell Counties, which are north of the extensive Hugoton gas area and may some day be part of it. At the close of the year there were 17,317 wells in the state rating as producers. By far the larger share (14,000) were classed as strippers and allowed to flow 100 per cent of their potential capacity, thus accounting for 33,500 bbl. a day. The remaining wells, capable of producing from 15 up to over 6000 bbl. per day, were limited in output according to these amounts. The largest wells having a potential of from 3000 to 7000 were allowed to flow from 2 to 3½ per cent of their official potential capacity. The percentage rises until wells of 15 to 20-bbl. capacity have a rating of slightly over 83. On the basis of these calculations the total potential capacity of all wells was 1,667,814 bbl., and the daily amount allowed was 175,851. Nine of the pools most recently opened were still unable to market their oil and were classified as "shut-in" pools. Total production for the state for 1936 was somewhat over 58 million barrels. Striking Geological Data Some interesting geological data were uncovered by deep drilling during the year. The most remarkable bit of information is the discovery

Jan 1, 1937

By N. A. Rose, E. L. Spain

THIS study was undertaken primarily to determine the reasons for certain variations in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates in some cases exhibited marked differences in specific gravity crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents. INTRODUCTION When it is stated that the aggregate from one point is inferior to that from another, it must not be construed to mean that the gravel is unfit for use. The classification upon which such aggregate ratings are based is largely arbitrary, thus inferiority or superiority is merely relative. Samples of gravel were selected from stockpiles at the dams of the Tennessee Valley Authority under construction, from the stockpiles of private companies along the river, and from samples taken by the gravel- exploration barge of the T. V. A. One hundred or more gravels of each size studied were selected at random by taking small handfulls while walking around the piles. These were separated according to the different mineral or rock constituents present, and the percentage of each constituent was obtained by counting. At least three such samples were taken from each size, and all checked with one another within a few per cent. The results were then averaged. In order to check on the accuracy of such sampling, a whole sample was taken from one point after the gravel was thoroughly mixed. The two methods gave approximately identical results. SOURCES AND TYPES OF MATERIALS The sources of gravel found in the Tennessee River are numerous and varied. The river itself traverses several geologic provinces, each

Jan 1, 1937

By L. W. McKeehan

The occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note.' This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. Method of Preparation The material in which the crystals here dealt with were grown was made from 1/8in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400" C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of traveling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, as nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection. Measurements The wire in the etched state was next mounted in a goniometer of special form which allowed the measurement of the spherical coordinates of the normals to any plane surfaces left by the etching. These coordinates were most conveniently a polar distance, 8, from one direction of the wire axis, and an azimuth or longitude, ?, from an arbitrary prime meridian. The region to be described more particularly is shown at a low magnification in Fig. 1, which gives two different views, differently illuminated to show the spatial relationship of a crystal occupying most of the part shown and of an inclusion, or rather a series of three inclusions suspected of being twins based on the principal crystal.

By F. N. Rhines

I. An Outline of the Theory of the Sintering of Pure Metal Powders SINTERING may be defined as the process by which powders bond themselves into coherent bodies, usually, although not necessarily, under the influence of pressure and elevated temperature. For the sake of clarity and simplicity, the present survey will exclude from consideration the sintering of mixed or alloyed powders, with attendant complications, but at the risk of overlooking information of general applicability. Sintering in the presence of a liquid phase is thus automatically eliminated. The sintering of alloys involves much additional subject matter and deserves separate consideration. Since the literature of the subject is extensive and widely scattered, it will not be feasible to consider the contributions individually. Instead, the subject matter will be classified according to experimental observations and theory, and will be presented in summary form. It should be noted that the appended list of references does not constitute a complete bibliography; it includes only those works quoted below. More extensive bibliographies are included in several of the references; see particularly references 7, q, 28, 34, 38, 50, 52, 54 a "Bibliography on Powder Metallurgy" published by the Library of Congress and a pamphlet published by the Metals Disintegrating Co. entitled "The Field of Powder Metallurgy and Bibliography." II. Summary of Experimental Observations The following classified list is composed of general statements of established fact derived from the experimental results reported in the published literature. A few contested observations are included, because of their potential importance; these are labeled as such. Any satisfactory and complete theory must be capable of explaining all of the uncontested facts. Obviously, some important facts may be missing from this list and these may hold the key to the correct explanation of the sintering process, but the possible lack of such material should not deter attempts to understand the subject on the basis of what is available here. A. The Initial Bond at Room Temperature a. To a limited extent uncompressed powders and massive metals adhere at room temperature.28 Clean tin powder forms a weak "cake" on standing at room temperature, the strength increasing with time. Clean gold surfaces adhere on light contact,"' as do those of many other substances, including nickel." b. Upon compression the strength of the bond is increased progressively.28 There is a limit of pressure

Jan 1, 1946

By W. A. Gibson, Zay Jeffries

It has been known for a number of years that certain aluminum alloys could be hardened by quenching from a temperature of about 500' C. Immediately after quenching the total increase in hardness is not marked, but the hardness increases gradually so that after about 4 days, it has reached a maximum. The actual increase in hardness probably continues for weeks or even months, but in order to detect the differences after 4 days, it is necessary to make tests at rather long intervals. So far as is known to the authors, Alfred Wilm was the first to discover these properties in aluminum alloys.' The aluminum-copper alloys are amenable to this treatment and the addition of magnesium makes the heat-treatment effect more pronounced. Until recently heat treatment of aluminum alloys has been confined to the worked alloys in the form of sheet or extruded products. The alloy that has been most used in this connection is known commercially as duralumin and has about the following composition: copper not exceeding, 6 per cent.; magnesium not exceeding, 2 per cent.; manganese not exceeding, 1 per cent.; commercial aluminum,2 balance. A typically good alloy in this range consists of: copper, 4 per cent.; magnesium, 0.5 per cent.; manganese, 1 per cent.; commercial aluminum, balance. This alloy can be rolled into sheets or extruded; and in this condition it can be heated in the ordinary furnace atmosphere to a temperature near 500° C. and quenched in water. After about 4 days it will have the following physical properties: tensile strength 55,000 to 60,000 1b. per sq. in. (3866 to 4218 kg. per sq. cm.); elongation in 2 in., 15 to 20 per cent. No harmful effects of the furnace gases or even the air, if the heating is effected in an electric furnace in an air atmospherc.

Jan 1, 1921

By John Goheen

RECENTLY the head burner at a brick. plant with over 40 years' experience said that he had burned brick by guess for over half his lifetime and had used pyrometers for 2 1/2 years but hoped that he would never have to burn kilns without pyrometers again. The ceramic engineer in making a special study of the burning of clay ware and the effect the heat of the kiln has on color and vitrification is also rapidly placing the burning of clay on a twentieth-century basis. Clay ware may be divided into various groups, brick and drain tile; sewer pipe; firebrick; and pottery, which, in turn may be subdivided into special classes. As nearly as the analysis of the clay type of kiln, etc., will allow, there are practically the same problems to solve in burning in all of the processes or operations. The underlying objective is the same, namely the production of the best grade of ware under the most efficient and economical manufacturing system. The principal problem in the production of clay ware is the burning off of the kilns. The most modern steam shovel may dig the clay and the most advanced types of pug mills and wire cut machines or molds of various kinds may be installed, but unless the drying and burning of the ware is successful, all of the previous operations will be useless. On this final operation depends the entire result of the plant. In reality, burning of all. clay ware is purely a heating proposition. The kilns, or furnaces, should be so designed as to give equal distribution of heat. Consequently, the problems of design and construction of kilns to produce equal distribution of heat require serious consideration, as do also the questions of heat control and draft control. The three most important factors in the burning of practically all types of kilns may be

Jan 9, 1919

By G. Sachs, L. J. Ebert, W. F. Brown

IT is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to the same strength level (i.e., the same tensile strength in a conventional tensile test), However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features-the high speed, the notch, and the bending-the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels3,4,7,8 have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests, In an attempt to analyze the fundamental nature of this test,8 it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom, The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension, This triaxial stress state occurs at a point in the interior of the notch specimen, It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present, This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors, This is contrary to the behavior of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1946

By E. C. Houston

The presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximately 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A.7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;" in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process. developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. Description OF Process Metallic magnesium is produced electro-lytically by the Dow and the Elektron

Jan 1, 1949

By T. Sterry Hunt

The deposit of rock-salt which is known to exist along the eastern shore of Lake Huron, in the province of Ontario, has lately been more completely explored than before, by a boring with a diamond drill, put down by Henry Attrill, Esq., of New York City, and the results obtained are so important in every way that I make no apology for presenting them to the Institute of Mining Engineers. I may be permitted to preface an account of this remarkable exploration, and of its results, with a historical sketch of the discovery and development of this salt-region. It was in December, 1865, that a boring was begun near the town of Goderich, in the hope of finding petroleum. In this the adventurers were disappointed, but, after passing through about 800 feet of limestone, they encountered a series of variegated marls, in which, at a, depth of 964 feet from the surface, a bed of rock-salt, 30 feet in thickness, was met with in May, 1866. The boring was carried to a depth of 1010 feet, ending in hard rock, and yielded, by pumping, a very pure saturated brine when examined by me in August of the same year. In the report of the Geological Survey of Canada for 1863-66, published early in 1867, I described this salt-well, with many geological details, and gave an analysis of the brine. In the next three years a considerable number of wells was sunk in and around Goderich, and numerous trials were made in various other parts of the region. Salt was found at Kincardine, thirty miles north-northeast from Goderich, at a depth of about 900 feet, and also at Clinton, thirteen miles southeast, at 1180 feet. Records of these wells, with analyses of the brine from them, were given by myself in a subsequent report of the Geological Survey, 1866-69, published in 1870 (pp. 211-244), together with accounts of various unsuccessful borings in the neighborhood, analyses of the brines from the various wells (including one analysis by Dr. Goessmann), with many details of the salt-manufacture at Goderich, at Syracuse, New York, and at Saginaw, Michigan. The geological character of the region was there discussed at length, and it was shown that the salt here occurs in the Onondaga or Salina formation, which

By S. F. Emmons

This mine is situated upon the western slope of the Meadow Valley mountains, about 70 miles by road from the present end of the railroad-track, which is at Uvada, on the UtahNevada boundary. This boundary-line marks fairly well a certain change in type of scenery from western Utah to eastern Nevada,—from a region in which the desert valleys predominate over the mountain ranges to one in which they are in about equal proportion. The railroad from Salt Lake City runs somewhat W. of S., for the most part along the bottom of the ancient Lake Bonneville. The latter part of its present course follows the axis of the southern arm or bay of that lake, now known as the Escalante desert. Along this bay, its line is a mathematically straight one, with no perceptible change of level for two " tangents " of more than 30 miles each, varying but a few degrees in direction. In the four or five hours re-

Jan 1, 1902

By C. M. Tucker, Kent R. Van Horn, W. P. Sykes

RECENT investigations of the molybdenum-carbon alloys have been reported by Becker and Ebert1‡, Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metallographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-fish intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. METALLOGRAPHIC INVESTIGATION A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500° to 1600° C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively

Jan 1, 1935

By F. N. Rhines

STUDIES upon the sintering of metal powders, in the solid state, have led to the proposal that the surface energy of the powder particles provides the driving force that causes points of contact between pairs of particles to grow into broad welds which isolate the residual vacant space into pores that tend to spheroidize and gradually to diminish in total volume.' Investigators differ with regard to the mechanism of the movement of the metal, under the influence of surface energy, to accomplish these changes. One school asserts that there is a mass movement of the metal, referred to as a "viscous flow," while the other school prefers to view the movement as a self diffusion process, wherein individual atoms are, transferred without disturbance of the basic pattern of the crystal lattice. Extensive experimental studies upon the sintering of copper, conducted recently by A. J. Shaler,2 have been in- terpreted by their author as support for the viscous flow mechanism of transport, the theory of which was developed originally by J. Frenkel.3 Duplicating a portion of this work with minor changes, G. C. Kuczynski4 is led to the alternate view, namely, that the initial stages of sintering, at least, proceed as a self-diffusion process. Both of these investigations were designed to deal with an isolated unit of sintering, i.e., with the shrinkage of a single pore, or with the growth of a single point weld. It remains to ascertain the behavior of a typical metal powder compact composed of a large number of particles of varying size and sintering to a body with a multiplicity of pores. The observation of density changes alone during sintering is not sufficient in such a case; it is essential to know how the internal geometry of the compact changes. This has been the object of the present investigation, the results of which are used to support the self-diffusion mechanism of sintering. The present studies consist in the measurement of the number of pores as a function of size and time at temperature during the sintering of a copper compact made from a commercial copper powder lightly pressed and sintered in several different atmospheres. A brief survey was made also of the change in shape of the pores, under the influence of the same variables. All of this was done by direct observation with the microscope. Densities were measured on the same sample. It is found that, while the compact is exhibiting an overall shrink-

Jan 1, 1951

By W. C. Coffin

Fire-brick stoves have become a necessary part of the modern coke blast-furnace equipment, and are also superseding the cast-iron pipe stoves in anthracite- and charcoal-furnaces. The brick stoves in general use are of either the Cowper or Whitwell type, or modifications of these bearing the names of those who invented the alterations from the original types rather than any real departure from then]. All these stoves have approximately the same valve-equipment and follow the same line of operation. The waste gas from the furnace enters at one port and burns in a single combustion-chamber, and the heated products are drawn through the various passe; in the brickwork to a stack of proper height to create the necessary draught. The last passes of these stoves receive a very small percentage of the heat from the gas, owing to their extreme distance from the combustion-chamber; and this chamber also suffers great deterioration in the attempt to force the heat into the farthest passes. At best, about 70 per cent. of the heat taken up is held in the combustion-chamher and the first down-pass of the Whitwell stoves. Mr. Hugh Kennedy, Manager of the Isabella Furnaces, Pittsburgh, Pa., who has had a large experience with the fire-brick hotblast stoves, was so strongly impressed with the fact that but about thirty per cent of the brick of the average stove were doing proper duty as heat-agents, that, after careful study and experiment, he had three 20- by 60-feet stoves constructed with a view of more uniformly heating all the brick. In these the general lines of the Whitwell stove are followed, with the blast-connections unaltered, but gas is introduced at the bottom of each pass, and outlets are provided at the top, so that the gases have a direct natural draught in each pass and the highest heats are obtained at the bottom instead of the top. The natural tendency being toward the reverse condition, the brickwork soon acquires an almost uniform temperature.

Jan 1, 1893

By H. J. Hand

STATISTICAL methods are becoming increasingly important for inter-preting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor,1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.-Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of vari-ables more or less constantly tending to affect it. As pointed out by Daeves, 2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such plants. ?

Jan 1, 1938

By L. D. Jaffe, J. H. Hollomon

THE effect of tempering temperature and time upon the properties of quenched steel is clearly a subject of great practical importance, as well as of considerable theoretical interest. It would be very desirable to be able to predict the properties of a quenched steel when given any selected tempering cycle, with a minimum of experimental work upon that heat or even type of steel. Two problems are involved: one consists of relating the structure obtained to the physical properties, and will not be discussed here; the other, with which this paper deals, involves the relations of time, temperature and composition with the structure obtained on tempering. Indentation hardness is perhaps the most convenient quantitative measure of the tempered structure, or of what might be called the "degree of tempering." Undoubtedly, it is not an exact measure, and in some cases (as when temper-brittleness occurs) pieces of the same quenched and tempered steel may have widely differing properties at the same hardness. However, hardness has the advantage of being simple to determine and is certainly the most widely used indication of the degree of tempering. Moreover, for fully quenched steels that are not temper-brittle and do not contain retained austenite when quenched, it appears that, in general, if the hardness of the steel is the same, the tensile and impact properties will also be identical, whether a high or a low tempering temperature is used. The tempering charts available in the metallurgical literature usually give the hardness as a function of tempering temperature for only one tempering time. However, in practice, tempering times frequently vary, and a method of converting tempering curves for one time to tempering curves for some other time would be very valuable. It is also advantageous, in determining the tempering treatment necessary for a given part, not to have to temper samples at several temperatures for the time used for the commercial tempering operation. A more satisfactory procedure would be to employ times of the order of 10 to 30 min., rather than 5 or 10 hr., and if possible to use only one temperature. Furthermore, it is frequently desirable, for reasons such as temper-brittleness,* to obtain a given hardness with short times at relatively high temperatures, and it would be convenient to be able to compute without tests the time required to produce this hardness. Remarkably few quantitative studies of the hardness of quenched steel tempered over wide ranges of temperature and time

Jan 1, 1945

By L. S. Castleman, H. A. Froot

A study was made of the growth kinetics of B-brass layers in a-brass us y-brass diffusion couples in which both phases were saturated in the 6 phase. It was found that useful estimates can be made of the difhsion coefficients at the ß-phase interfaces from interface displacement data, which are relatively easy to measure experimentally; also, a useful estimate can be made of the mean heat of activation for diffusion from layer growth data. The effects of pressure on layer growth kinetics were explored and found to be consistent with a vacancy model for diffusion in 6 brass in both the disordered and ordered temperature range. 1 HE study of multiphase diffusion receives relatively little attention in comparison with that devoted to diffusion in homogeneous materials. Of the hundred or so papers on diffusion written each year,' only a few are devoted to the subject, and it is the rare review article2,3 that devotes any space to multiphase diffusional phenomena. This is unfortunate, since the metallurgist frequently encounters practical situations involving cementation processes such as cladding, protective coating of metals, and so forth in which he needs guidance of a fundamental nature. The investigation of multiphase diffusion phenomena is complicated by the fact that one must consider reactions at phase interfaces as well as the migration of atoms within the individual phases; these reactions cause the interfaces to be displaced within the diffusion zone. The relative displacement of two adjacent interfaces corresponds to the growth of an intermetallic layer, and it is not difficult to determine experimentally the kinetics of layer growth. In the past few years it has been pointed out4,5 that valuable fundamental information may be gained about diffusion coefficients and the concentrations at interfaces through a study of their motion. Accordingly, it is the purpose of this paper to report the results of an investigation of interface motion in a simple multiphase binary system. In the work reported herein, attention was focussed on the growth of a 6 -brass layer in a diffusion couple prepared from a- and y-brass compositions saturated with respect to the 6 phase. This particular system was chosen for a number of reasons. First, the bcc ß-brass phase is disordered for all compositions at temperatures above 468°C and becomes increasingly long-range ordered for all compositions at temperatures below 454° C;6,7 thus, the effects of a variation in order on interface displacement could be determined. Second, diffusion coefficients have already been obtained as a function of temperature in the ß phase both in the ordered and disordered Re- and a theoretical picture of the mechanism of diffusion in this and other ordered solutions is emerging.11'12 Third, some thermodynamic data are available for the a-, ß-, and ?-brass phases,13,4 and these data could be used to gain insight into questions of phase equilibria and concentrations at phase interfaces.

Jan 1, 1963

By Howard A. Meyerhoff

In western Argentina, in the Province of Mendoza and the Territory of Neuquen, there is a series of solid bitumen deposits which are claimed to be the most extensive in the world. In a linear belt 500 km (311 miles) long, roughly paralleling the axis of the Andes but occupying a variety of positions with respect to the orogenic structures, more than 100 outcrops have been reported. Approximately 70 of these have been prospected, and some mining has been planned or attempted for about half this number. Limited tonnage, high sulphur content, inaccessibility, labor shortages, and disastrous fires have taken a heavy toll among these operations, and in 1947, only 4 deposits were being actively mined, but 8 more were being explored and developed with a view to placing them in production. Inasmuch as these deposits are currently yielding a substantial fraction of Argentina's limited domestic supply of solid fuels, a brief account of the deposits and of the small industry based upon them will provide a commentary on Argentina's fuel problem. Character of Solid Bitumens The solid bitumens of Mendoza and Neuquen are petroleum derivatives, as is indicated by the following ultimate analysis : Constituents Per Cent Hydrogen.................... 6.8 Carbon...................... 82.4 Nitrogen..................... 1.6 Oxygen...................... 2.7 Sulphur...................... 2.2 Ash.......................... 4.3 100. 0 In physical appearance they bear a close resemblance to coal and are commonly called carbon. Their specific gravity has an extreme range of 1.10 to 1.777 in 36 samples weighed, but the average is between 1.14 and 1.24. The material is black, lustrous to dull, with blocky to sub-con-choidal fracture. Though brittle, the purest material is softer than anthracite and exhibits slightly more cohesion. This bituminous material is generally known as asfaltita or asphaltite, but definitive chemical studies indicate that the term asphaltite or grahamite can be applied correctly only to the exceptionally pure material of the Auca Mahuida district in Neuquen. Some other name should be used for the chemically variable bitumens found in all other districts, and the designation "asphaltitic pyrobitumen" has been proposed by Carlos A. S. Piscione.1 At the present time these bitumens are finding favor as solid fuel and as a gas-producing medium. They yield heat values of 8650 to 9750 cal,2 or 14,500 to 16,750 Btu per pound, and in consequence of their excellent heating qualities and the scarcity of imported coal, they are marketed as far away as Buenos Aires at a price of go to 95 pesos, or approximately $22 to 23, per metric ton. In burning, the material swells and decomposes into solid, fluid, and gaseous fractions which burn violently though nonexplosively. Its combustibility has been responsible for disasters and virtually complete destruction at Mina La Es-peranza and Mina Santa Marta, and for minor mishaps elsewhere, as at Mina Escondida in August 1947.

Jan 1, 1949

By Milton E. Wadsworth

The reduction of a metal in an aqueous solution may be defined in terms of its source of electrons. In electrolytic reduction electrons flow as a result of applied voltages. In other systems electron sources are reducing gases or metals of lower electron affinity. In the latter two cases it is increasingly evident that reduction is electro-chemical in nature in that electrons flow through one or more conducting phases even though the discharge reactions may not be rate controlling. Electrode processes impmtant in reduction and metal deposition are reviewed and extended to contact reduction by precipitation (cementation) on mme electropositive metals. Contact reduc- tion Processes are ancient in origin and represent techniques which have had successful application for hundreds of years. In spite of this, little has been understood in terms of the dynamic properties of such systems or of important side reactions. In recent years an increasing amount of laboratory work has been carried out on contact reduction and an attempt is made here to summarize the important findings. Undoubtedly the interest aroused recently may be attributed to improved reactor design which has demonstrated on a commercial basis accelerated metal recovery by taking advantage of important kinetic and chemical parameters. of gold cyanide (Au(CN)-), respectively. The most common method for the reduction of ions in solution is by electrolysis. The impure metal is made the anode and the ions are reduced at the cathode. Leach liquors containing reducible ions may similarly be reduced electrolytically using an inert anode. The latter process is referred to as electrowinning. In recent years hydrogen has been used successfully as a gaseous re-Metallurgical Society of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). He was also a member of the Executive Board of the Metallurgical Society (AIME). In 1957 Dr. WADSWORTH was given the AlME Best Paper Award as coauthor of a paper on the roasting of sphalerite. On July 1, 1968 Dr. WADS-WORTH started an 24 month assignment in the Philippine Islands to assist in the development of graduate metallurgical engineering at the University of the Philippines. In addition to graduate teaching and curriculum development he will establish research programs to develop extraction processes for metals production in the islands. The project is supported by the Ford Foundation through Educational Projects, Incorporated.

Jan 1, 1970

By B. K. Miller, R. S. Bradley

The principal producing areas of fire clay in Missouri are: (I) the east central district, which includes Audrain, Callaway, Montgomery, Warren, and Boone Counties (Fig. I); (2) the St. Louis district, which includes St. Louis and St. Louis County; (3) the north central Ozark district, which includes Franklin, Gasconade, Osage, Maries, Phelps, and Crawford Counties. Most of the semiplastic‡ fire clay is found in Audrain, Callaway, Montgomery and St. Louis Counties, and in St. Louis. Flint fire clay is found in Callaway, Audrain, and Montgomery Counties and in most of the north centra! Ozark district. High-alumina diaspore clay is found only in the north central Ozark district, except a few deposits found in Montgomery County. This paper is concerned with the semi-plastic fire clay that occurs in the east central Missouri district near Mexico, Audrain County, Missouri, which is mined by the open-pit method as practiced by the A. P. Green Fire Brick Co. About one-fourth of the semiplastic fire clay in that district is mined in shaft mines, and three-fourths in open pits.

Jan 1, 1942

By Dorsey A. Lyon, Robert M. Keeney

Page I. Introduction..........234 I1. Chemistry oF Copper Smelting...235 1. Native Copper Ores.......235 2. Oxide and Carbonate Ores....235 3. Sulphide Ores.......236 (a) Elimination of sulphur ...236 III. Reverberatory Copper Smelting...237 IV. Substitution of the Electric Furnace for the Reverberatory Furnace..................... 238 V. Smelting of Fine Michigan Native-copper Concentrates in the Electric Furnace.................. 239 1. Conclusions.................240 VI. Proposed Process for Electric melting of Fine Native-copper Concentrates.................. 241 VII. OrdINary Copper Blast Furnace 'Smelting......... 245 1. Prerequisites.................. 245 2. Losses .................... 247 VIII. Experimental Data on the Electric Smelting of Raw Sulphide. Oxidized and Carbonate Ores............. 248 1. Vattier's experiment................ 248 2. Wolkoff's experiments................ 249 3. Experiments of Stephan.............. 250 (a) Conclusions of Stephan ............ 251 IX. Smelting of Sulphide Ores in the Electric Furnace...... 251 1. Ores Treated.................. 252 2. Conclusions................... 253 X. ELectric Furnace vs. the Reverberatory Furnace and Blast Furnace as a Melting Agent.............. 253 XI. Smelting of Sulphide Ores without Roasting or Partial Pyritic Smelting............254 XII. The Electric Blast Furnace vs. the Copper Blast Furnace for Partial Pyritic Smelting.......259 1. Metallurgical conditions......259 2. Mechanical considerations......259 3. Comparison of costs.......260 (a) General considerations .....260 (b) Cost of plant........260 (c) Amount of electrical energy...260 (d) Cost of smelting.......261 (e) Cost of electrodes........262 XIII. The Use of the Electric Furnace in the Smelting of PyRITIc ORES : 262 XIV. Summary...................... 264

Jan 1, 1914