Search Documents

By David E. Hyatt, Christopher H. Cox, Franklin T. Davis

INTRODUCTION The composition of water used in the flotation process has always been of primary interest to the flotation metallurgist. It is by alteration of the chemistry of the water introduced to the process that flotation separation is effected. In only a few cases has it been necessary to treat available water prior to use in the process. In the past, flotation tailings were treated for the removal of solids via the tailings dam and water decanted from the dam was either recirculated to the process or discharged to the surface water system. The choice of recirculation or discharge was based upon water availability, effect of recycle water on the process, and economic considerations. The Federal Water Pollution Control Act Amendments of 1972 have charged the United States Environmental Protection Agency with establishing effluent limitations from point sources of discharge into the navigable water of the United States. A detailed study, sponsored by EPA, of the water of ore processing plants took place in 1974 and 1975 and guidelines for these plants will presumably have been published by the time this paper has been presented(1). The action of many of the individual states preceded the EPA in this attempt to regulate the quality of the water discharged from industrial point sources. Even with recycle of tailings water, some water is discharged from tailings dams into the substrata and at least one state is currently preparing guidelines for the quality of water discharged into the substrata.

Jan 1, 1976

By Colin C. Harris, Nathaniel Arbiter

The flotation operation can be analyzed in terms of three groups of variables. The first, largely independent of control by the operator, embraces the fixed physical and chemical properties of the ore minerals. The second includes all chemical and physical effects imposed on an ore after mining that influence its floatability. These can be either purposefully or accidentally applied. The third embodies the flotation-machine characteristics which realize the potential floatability of selected ore minerals in terms of grade and recovery levels. The machine effectiveness thus depends not only on its own contribution, but on the prior influence of all other variables on floatability. HISTORICAL DEVELOPMENT From the earliest days, flotation mills used many types of machines. Hoover 20 in 1914 mentioned as then important the Potter-Delprat tank for gas generation by acid, the DeBavay cones for skin flotation, the Elmore mixer and separation chamber for vacuum flotation, and his own modification of the Mineral Separation cell for the agitation froth process. Less important at the time were the MacQuisten tube and the Hyde cell. By 19274~ scores of machines had been developed and dozens had found their way into mills. From then on, however, under the scrutiny of competitive tests, many fell into disuse. Taggart in 19454~ classified processes broadly as skin flotation and froth flotation, dividing machines for the latter into the three categories: bubble column, pulp body, and combination.* Under 'bubble column' he listed all pneumatic, cascade, and subaeration cells; and under 'pulp body' those cells in which gas was generated by boiling, chemical action, and pressure reduction, as well as the agitation-froth type. At that writing skin flotation, the cascade machines, and all pulp body and combination machines were said to be extinct, leaving pneumatic and subaeration types dominant (u. S. practice). The process of elimination has continued to the present, with almost all pneumatic cells succumbing to the pressure of competition from subaeration machines. The only new machines to appear in recent years have been double-impeller types f and these have met with only limited acceptance.

Jan 1, 1962

By Charles R. Keyes

PAGE I. Introductory............ 140 II. Location and History...........140 III. Surface-Relief of the District....... 141 IV. General GeoloGic Features........ 142 1. Main Relationships and Map....... 142 2. Résumé of Geologic History..143 V. Geologic Formations Represented...144 1. Broader Considerations......... 144 2. Geologic Section.......... 145 3. Nomenclature.......... 146 4. El Pasan Limestones..146 5. Santa Rita Limestone.... 146 6. Silver Shales........... 147 7. Bella Shales........... 147 8. Berenda Limestone..147 9. Grande Limestone... 148 10. Lake Valley Limestone........ 148 11. Sierra Limestone.......... 149 VI. Unconformities........... 149 VII. Geologic Structure.......... 150 1. Main Characteristics......... 150 2. Folding........... 1.50 3. Faultings........... 150 4. Relations of the Eruptives...153 VIII. Geologic Relations OF the Ore-Bodies...... 154 1. Governing Factom......... 154 2. Position.......... 154 3. Relations to Foldings...155 4. Relations to Lines of Dislocation... 15.5 5. Relations to Present Surface.Relief..156 6. Relations to Eruptive Rocks...157 7. Relations to Lithologic Nature of the Rocks.... 158 IX. MINERALOGIC CHARACTER OF THE ORES...... 158 X. Origin of the Ore.Deposits..159 1. General Statement......... 159 2. Original Source of the 0re.Materials...160 3. Contact-Metamorphism of the Region... 161 4. Process of 0re.Concentration..162 5. Lowering of Ground-Water Level..162 6. Formation of Cerargyritic Ores...163 XI. Recapitulation........... 168

Jan 1, 1909

By Robert Gilman Brown

The original power-plant of the Standard Company has been described* by Mr. T. H. Leggett, late president and manager of the company; but since the presentation of his paper considerable additions have been made, which will be found interesting because of the engineering features involved and of the attainment of a high degree of flexibility with the inflexible, two-wire, alternating system of electrical transmission. Although these additions have been completed during the last year, they constitute, to a large extent, only the carrying out of plans that belonged to the original conception of the installation. The regular operation of the water-power through the winter proved very difficult; there was a considerable length of ditch to be kept open, and, as the stream is small and any freezing night may stop the whole flow of water, there was the .additional trouble of having no reserve to draw upon. The rule for the winter is, that after a night of hard frost water begins to move in the canon before noon on all but the coldest days. To obviate the nuisance of the anchor-ice, and to make available all of the water, a dam of sufficient height to impound several days' run of water has been built across the canon, 3875 feet above the power-house, and provided with pressurepipe well below the surface. In place of the 1571 feet of pipeline from penstock to power-house, there has been substituted a line 3875 feet long to bring water direct from the dam. The dam is of logs, cribbed up in squares of about 12 feet, ballasted with earth and rock and sheathed on the water-face with 3-inch plank.

Jan 1, 1897

By C. A. Stetefeldt

The iron-ore deposits worked by this Company occur in lenses 200 to 1000 feet long and 5 to 80 feet wide, and stand at an angle of from 65' to 75, with a vertical height of 250 to 500 feet, other lenses occurring below. A number of the deposits were first worked as open pits, which in some cases were carried to the depth of 150 feet, when, owing to the weakness of the walls, underground mining was adopted. While the ore was being removed from the open pit, shafts mere in several instances sunk into the foot-wall, the intention being to mine the ore with breast-stopes of an approximate height of 20 feet, followed by underhand-stopes of the same height, leaving floors between of the necessary thickness to support the walls, or to effect the removal of the ore by means of what is known as the stall system. As the work progressed, however, it was found that the walls (which are of chlorite) were too weak to permit the working of breast-stopes 20 feet high, there being frequent heavy falls of ground from the hanging and, in some instances, from the foot. The plan of following breast-stopes with underhand-stopes was, therefore, abandoned. By working breast-stopes only, but little more than one-half of the ore could be removed, and that only at an excessive cost, the ore being so hard that power-drills with 3 1/8-inch pistons . and 6-inch stroke, working under 60 pounds of compressed air, are able to drill but 8 feet in ten hours as a yearly average, while from 6 inches to 2 feet is a common result of ten hours' drilling. It was plain that some other system of mining must be adopted, and it was proposed to sink by levels of 75 feet, carrying in the cross-cuts from the shafts and working out the ore each way from the shaft from foot to hanging, and from 15 to 20 feet in height. When this has been done, drift-sets consisting of caps and legs are set up the whole length of the opening and connected with the cross-cut; the necessary openings for ladder-ways and chutes or mills are timbered from

Jan 1, 1893

By C Gunther

Secondary minerals are the result of a process of concentration and enrichment and are commonly richer than the primary minerals of the same deposit. Secondary ores that contain abundant sulphides are commonly dibtinguishable in the field from primary ores; this distinction is more difficult with ores that carry a small quantity only of sulphide minerals, and microscopical examination of the ore in thin section is advisable in all doubtful cases. It is frequently difficult, and in some cases impossible, to determine the primary or secondary character of quartzose gold ores. The safest guide is the presence or absence of gaseous or fluid inclusions in association with the ore minerals; such primary association coupled with a lack of traces of oxidation is indicative of primary origin. Any ore that carries traces of oxidation, such as iron stains, dendritic oxides of manganese, kaolin and so forth must be considered to have been acted upon by surface agencies, and secondary enrichment must be suspected. Further examination, however, may indicate that the contained value is primary, and, therefore, persistent in its vertical distribution. The manner of occurrence of secondary minerals is frequently characteristic; secondary minerals, being due to the action of surface waters, are commonly found in cracks through earlier minerals, or as crusts lining vugs or surrounding nucleal masses, or in general, in some distribution later than and not conforming to the arrangement of the primary minerals. Secondary sulphides are often found as soft black pulverulent masses or coatings, although they frequently occur well crystallized or as

Jan 1, 1932

By Richard A. Busch, Roy L. Soderberg

Large, high, open stopes resulting from vertical crater retreat (VCR) and similar methods are usually filled with sand tailings to support the stope walls and make it possible to mine the pillars. The hydrostatic head resulting from these high stope fills demands extremely heavy bulkheads in the crosscuts to withstand the pres- sure. Occasionally, these bulkheads fail because there are no drains or the installed drains are inadequate. Costly flooding of the mine and loss of life result from these failures. With proper design of blanket drains and filters, the fill can be made failure-proof, requiring only a minimum bulkhead, designed specifically for zero water retention. The effectiveness of the blanket drains can be increased by laying perforated pipes on the bottom of the crosscut within the blanket drain. These drains can have a safety factor of 10 with minimal expense. When the water is properly drained, the hydrostatic pressure on the bulkhead is reduced to zero, leaving only the lateral pressure of the sand. This lateral pressure is partially dissipated by arching and shear against the crosscut walls and consolidation of the tailings as the water is drained. The bulkhead should be placed at least one cross-cut diameter back from the collar of the drawpoint.

Jan 1, 1983

By Charles R. Keyes

Prefatory,........323 Foundation of classificatory schemes in general..325 Past opinion on the classification of ore-bodies,.326 Nature of ore-deposits,....... 326 Definition........326 Fundamental law of origin.... 327 Significance of ore-bodies,.... 327 Date of origin........328 Original source of ores..... 328 Alteration of ore-bodies,....329 General methods of ore-formation.... 330 Ascension verm lateral secretion... 330 Replacement.......330 General factors in classification....332 Genesis in ore-classification....332 Literature of ore-deposits...... . 333 Criteria of ore-classification,..... 335 Primary grouping of ore-deposits..... 338 Hypotaxic deposits......341 Eutaxic deposits...... 341 Ataxic deposits....... 313 Secondary categories of ore-bodies....343 Ternary phases of ore-deposition.....344 Types of hypotaxic or surface deposits..... 344 Illustrations of eutaxic ore-bodies.... 347 Examples of ataxic ore-bodies.....352 Recapitulation.. .. .. .. 355 Prefatory. Much has been written on the genesis and classification of ore-deposits. Much remains yet to be written on the subject

Jan 1, 1901

By J. R. Thoenen

Six or seven years ago the United States Bureau of Mines started development of instruments for the purpose of accurately measuring the vibrational movement of the earth in the vicinity of quarry blasts. For this work a new type of seismometer has been developed. A number of these have been constructed, the accessory field equipment has been assembled, and approximately 200 field tests of actual quarry, blasts have been made. The results of some of these tests have been published 2/ and others are the subject of two manuscripts now in preparation. So far the attention of the investigation has been centered on ascertaining the characteristics and behavior of the ground vibrations. Occasionally, when opportunity arose, measurements of the vibrations occurring in houses or other structures caused by-quarry blasts were made, but without any attempt at direct correlation or interpretation. During 1936 the National Bureau of Standards conducted some experiments to determine the normal vibrations to which the wells and floors of buildings are subject. Cooperation of the Bureau of Mines was requested in measuring the displace-ment. This afforded an opportunity to study the affect of mechanically induced vibrations end make limited comparison with previous records of vibrations from blasting. This paper deals with the experiments made in cooperation with the Bureau of Standards and includes some comparisons with effects from quarry shots. The results are in the nature of a progress report only, and are not intended to draw definite conclusions. These tests were concerned with the determination of the maximum amplitudes of vibration possible in the floors and walls of a typical dwelling when subjected to commonly experienced vibrations. The dwelling tested was obtained by the National Bureau of Standards. It was a large four-story stucco building, 41 ft. south of the southerly curb of Park Road, in Washington, D.C., which was constructed about 1900 and was supported on overburden. The basement floor elevation was approximately that of the pavement of Park Road, Park Road runs east and west; the front door of the house faced north.

Jan 1, 1937

By W. H. Bassett, C. H. Davis

The ease and value of the application of spectrum analysis to industrial chemistry appears to be appreciated in few of the large works laboratories of this country. For 8 years, this analysis has been of great value to the authors in both analytical and metallurgical work. To the analyst the complete qualitative analysis of an unknown alloy, revealed by a spectrogram, is a sure basis for the planning of the most direct and rapid method of attack. As the determination of each element proceeds, the purity of precipitates may be checked as often as desired. The spectrograph proves invaluable in the recognition of impurities, the separation of which would entail a lengthy and difficult procedure, or when the weight of an unknown is less than is necessary to complete the desired determinations. A few hundredths of a gram will usually suffice for spectrographic analysis. In the separation of the rarer elements, the spectrograph will show, with precision, the point where each step has been successful. In zinc of certain classes, indium, gallium, and germanium have been isolated in this way; the presence of antimony in lake coppers has been proved; and bismuth has been detected in zinc and in alloys where the presence of a few thousandths of a per cent. would be harmful. An antimony precipitate in a delicate determination may contain a considerable proportion of tin or arsenic, both of which will be revealed. The spectrograph is consequently important to the metallurgist as well as to the analyst. Impurities in raw material are often a source of annoyance, especially when their detection involves delay and costly analytical work. Whethcr low conductivity in copper is due to arsenic, nickel, or something else may be cluickly found out. Residual traces of boron, magnesium, manganese, silicon, vanadium, and other deoxidizing agents are easily identified where wet analysis may fail to reveal their presence, even after days of effort. Complex alloys of any kind are dissociated by the spectro-

Jan 1, 1923

By William M. Baldwin, T. S. Howald, A. W. Ross

EXPLORATORY WORK THE related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal [ ] strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strips-20.29 and, to a lesser extent, yield strength7,11,17 and stress-strain curves" have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between earing tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture, a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1945

By R. E. Ricksecker, W. M. Baldwin, R. McC. Baker

INTRODUCTION THE development of residual stress in strip during rolling has not been systematically studied. A few scattered papers1-3 mention the existence of residual stresses in rolled strip or touch upon some of their consequences,4 but there is no report of experimental studies in the literature describing the effect of roll diameter, strip thickness, reduction per pass, metal or metal temper on the magnitude of residual stresses developed in strip. A knowledge of the effect of these factors is of utmost importance since the present trend in some mills to roll thicker castings brings the rolling operation directly into that set of conditions which, as will be brought out in the present paper, can develop residual stresses of a high order of magnitude. Fundamentally, residual stresses are developed when a metal is inhomogeneously unloaded from a plastic stress state. A quantitative treatment of the problem requires a reasonably complete understanding of both the plastic stress state existing in the metal during deformation and the elastic stress state that would exist in the metal if the metal deformed as a perfectly elastic body. Our knowledge of either state during rolling is so meager that we can make no more than certain limited predictions. The external stress state* operating between the roll and the metal consists of compressive stresses acting almost perpendicularly to the strip surface but vary [ ] ing in intensity both across the width of the strip and along the length of contact between the roll and the strip. An example of such a stress distribution is shown in Fig I. The nature of the internal stress state, produced by this distribution, is not known. Various investigators,5-7 however, have felt that a qualitative similarity must exist between the internal stress state so produced and that produced in a wide strip that is compressed between two flat-nosed punches. In the latter case the external stress state is represented by a uniformly distributed compressive stress acting perpendicularly over the face of the tool. The elastic internal stress state in this case is complex-the principal stresses showing

Jan 1, 1948

NEW MEMBERS The following list comprises the names of those persons who became members during the period Nov. 10, 1916 to Dec.10, 1916. BARNSDALL, THEODORE N., Treas. & Mgr., Highland Gas Co., 24 West Corydon. St., Bradford, Pa. BEASLEY, FRED E., Asst. Supt., Copper Refinery, Consolidated Mining & Smelting Co., Trail, B. C., Canada., BREWSTER, THOMAS T., Vice Pres., Gen. Mgr., Mt. Olive & Staunton Coal CO., 1012 Federal Reserve Bldg.,-St. Louis, Mo. BRINDLE ARTHUR ST. C.... Mining Recorder's Office, Trout Lake, B. C., Canada. BULLOCK, Harry E., Pres Kentucky-Jewel Coal Co., Lothair, Ky. BUTLER, PERCY BENNETT, Mine Operator :..P. 0. Box 335, Joplin, Mo. BUTLER, ROBERT S Supt., Three Johns Mining CO., ,Joplin,.Mo. CABOT, Godfrey, L., Carbon Black Maker, Gas Engr., 940 Old South Building Boston Mass.

Jan 1, 1917

By Henry M. Howe

In discussing the classification of iron to-day, we are to leave out of consideration the general division into non-malleable or cast iron and malleable iron, as to the adequacy of which no question has been raised; and to confine ourselves to the subdivisions of malleable iron. This has been classified, according to the extent to which the properties imparted by carbon are present (viz., resilience, hardness,strength, and, above all, the capacity for being hardened by sudden cooling from a high temperature), into (1) wrought iron which cannot be hardened, and (2) steel which can be hardened; and this classification I shall, for briefness, term the carbon classification. Until within a few years all authorities, both metallurgical and general, have concurred in explicitly recognizing the carbon-given qualities, and preeminently the capacity for being hardened, as the essential qualities of steel; this is laid down with clearness by every writer on the subject. For several years this old classification has not been sufficient to meet all our needs, since the genius of Bessemer, Siemens, and, I may add, Holley, has produced wrought iron which has been perfectly melted, and thus freed from certain mechanical adhering impurities. This causes what we call homogeneousness for want of a better word, and gives rise to many important qualities which the old wrought iron had not; qualities universally recognized, though not readily described. I shall, for briefness, style them the fusion qualities, and a classification based on them, a fusion classification. These qualities render the new product so vastly superior, for most purposes, to the wrought iron formerly known, that it is neces-

By Jesse O. Betterton

Recently some experimental work was conducted by the author in connection with the direct leaching of certain zinc ores with sulfuric acid with the object of subsequently recovering the zinc by electrolysis. The ores contained relatively large quantities of soluble silica, making it necessary to evolve special methods for handling the silicate solutions resulting from a leach of the ore, and also for the final removal of the silica before electrolysis. The problem was complicated by the presence of vanadium in the ore, the commercial recovery of which was very desirable. This paper, however, deals only with the silica phase of the problem. The zinc in the ore occurs in the form of a silicate (hemimorphite) and, to a very small extent, as the phosphate (hopeite) and carbonate (calamine); the vanadium is found as descloizite and vanadinite but mainly as descloizite. The experimental work was done in a plant producing 50 lb. of zinc = daily, in which the complete cycle of operations, including the final electrodeposition of the zinc, was performed continuously for one year. Some of the conclusions given here are the result of the operations in -this plant; the others are from laboratory tests inaugurated both as a guide to the plant operations and, in certain cases especially, to determine the limits in question. The practice in the 50-lb. zinc plant was to direct leach the ore crushed to pass 40 mesh, with spent electrolyte from the cells containing approximately 3 per cent. zinc and 10 per cent. free acid. This resulted in an acid leach solution and an ore residue. The acid leach solution was ' subjected to a special treatment for subsequent removal of vanadium; then the silica and vanadium in solution were precipitated together and removed as a "silica residue" by pressing through an ordinary plate and frame press. The next step was to treat the filtrate from the silica residue with zinc dust as a final purification step before it went to

Jan 1, 1923

By John C. Branner

Within a couple of years I have received many inquiries in regard to the manganese-mines of Brazil. These inquiries were doubtless directed to mc because I had lived and traveled in Brazil for more than eight years, and was therefore supposed to be pretty well acquainted with its geology and mineral resources. Somewhat to my chagrin, I not only knew nothing of manganese-mines in that country, but I had never before heard of the mineral having been found here in quantity, and I did not even know in what State the mines were located. The present summer found me in Brazil again, trying to finish up some of my early geological investigations along the northeast coast, and I have used the occasion to find out something about the manganese-deposits. Very little is known of these mines, even in Brazil. While at Pernambuco I was told that they were in the distant interior of the State of Bahia. In August I reached Bahia, and there I found out, concerning the mines and their geology, enough to be worth telling for the benefit of those interested in the mining or using of this mineral. Thus far, all the manganese-ore shipped from this State has come from two mines, the principal one of which is known as the Pedras Pretas mine. This was the first mine opened, is the best developed, and was the original discovery; the second one is on an adjoining tract, and the general geology and natural conditions are about the same in both. The Pedras Pretas mine is on the Nazareth-Amargosa railway, twenty-six kilometers west of the town of Nazareth, which is on tide-water, at the head of navigation, and is reached from the city of Bahia by a small side-wheel steamer that runs across the bay of Bahia and up the Rio Jaguaripe

Jan 1, 1900

By J. R. Kyte, R. L. Dalton, V. O. Naumann, R. L. Ridings, R. W. Greene

This paper presents a one-dimensional numerical method for calculating dissolved-gas-drive behavior for a single well or a linear reservoir. Pressure and saturation distributions can be calculated, including the effects of capillary and gravity forces. The analysis has been programmed for solution on the IBM 7090 digital computer. A comparison of experimental and calculated behavior for two linear models demonstrates that the method is suitable for calculating dissolved-gas-drive behavior under reservoir conditions of flow. Dissolved-gas-drive tests were run, at different production rates and with oils of different viscosities, on short (6.ft) and long (173ft) flow models. For tests approximating reservoir pressure gradients and flow rates, there was excellent agreement between experimental and calculated results. A series of calculations of well behavior for thin, horizontal, homogeneous, dissolved-gas-drive reservoirs shows that ultimate recovery is independent of production rate or well spacing in such cases. These calculations also show that Muskat's method and similar material-balance analyses are not applicable under some conditions particularly for high pressure drawdowns. INTRODUCTION The problem of calculating dissolved-gas-drive reservoir performance has received a great deal of attention throughout the oil-producing indusfry for many years. Really significant advances, however, have been made only in recent years. The rapid evolution of high-speed computing equipment and techniques has opened up new approaches to the problem and led to realistic, quantitative analyses free of many of the assumptions and limitations of earlier methods. The one-dimensional numerical method described in this paper includes the effects of both gravity and capillary forces. A number of test calculations, based on different rates, spacings, and rock and fluid properties, have shown that the method is adequate for systems that can be reasonably represented by a one-dimensional model (linear or radial) and in which fluid segregation perpendicular to the direction of flow is not important. Along with the development of mathematical methods, an experimental program was conducted and the data were used to test the validity of the theoretical basis of the mathematical method. Linear models were used and all experiments were run using 1,000-psig bubble-point oils. The use of long, high-pressure models enabled us to more closely approach reservoir gradients and flow rates. MATHEMATICAL FORMULATION DIFFERENTIAL EQUATIONS The differential equations describing dissolved-gas-drive behavior in one dimension dare summarized here. They include Darcy's law for flow of oil and gas (Eqs. 1 and 2) and the equations for conservation of mass for oil and gas (Eqs. 3 and 4). The oil and gas pressures are related by capillary pressure (Eq. 51.

By Plato Malozemoff, A. M. Gaudin

IN modern practice the major portion of an ore is reduced to flotation size by fine grinding. As the result of grinding fine enough to liberate most of the minerals, a substantial portion (generally 5 to 15 per cent) of the ore is inadvertently reduced to a size much finer than that necessary for liberation. This portion of most flotation pulps is very refractory to recovery by flotation. A reduction of one-quarter or more in recovery in this range of extremely fine particles can be observed. The loss in metals caused by overgrinding is appreciable. That this loss is characteristic of very fine particles has been suspected for some time;(l)† however, it was definitely quantified only recently.(2) Definite reduction in float-ability with reduction in particle size beyond a critical size of maximum floatability can be accepted now as an established fact. Formulating the Hypothesis In looking for the cause of the ill behavior of the finest particles it may be well to consider the essential differences between fine and coarse particles. A difference that immediately comes to mind is their intrinsic difference in size and consequently in relative extent of surface. If one agrees that attachment of mineral particles to bubbles must follow direct encounter of particles with bubbles one is forced to conclude(3) that the probability of encounter between a mineral particle and a bubble varies directly as the size of the particle, provided the particle is small compared to the bubble. In other words, the finer the particle the poorer its chance of being recovered in a given time of flotation. There is an effect, implicit in this theory, which should overcome the effect of excessive fineness of the particles; namely, flocculation of the particles. The floccules can be conceived as being simply larger particles and therefore capable of becoming attached to bubbles. And, indeed, in all the cases in which a sulfide mineral of near-colloidal size was successfully floated the mineral (but not necessarily the gangue) was flocculated. Moreover, it was shown experimentally(4) that galena previously flocculated by inorganic flocculators and then added to gangue

Jan 1, 1935

By E. P. Mathewson

W. W. (Pop) Adams' contribution is short and to the point. "I went to Pueblo about March, 1881, and started working for the Pueblo Smelting & Refining Co. in the sampling room, going from there to the assay and chemical departments, and ending in charge of the lead refinery on the night shift. I was there about two years, returning to California in 1883. The plant was under the management of Mather and Geist, plus Charley Ballard; Herman Schlapp was the metallurgist. Herman Schlapp's name remains prominently in my recollection of Pueblo for his never-failing kindness and charity to the young men who were trying to learn the Pb. game. John Allen, Walter Koehler, George Westcott, Charley Molson, and Alfred de Ropp were there with me. Schlapp and Koehler I have never seen since I left Pueblo; the others I have met often. , Alfred de Ropp I have often met-here, as he was manager of the Selby Smelting & Lead Co. of San Francisco, for years. 'He tells me that I gave him the rudiments. of American profanity at Pueblo; an apt pupil, for since then, by his own efforts, he has added largely to his vocabulary..

Jan 12, 1923

By Claus G. Goetzel

PRESSING of powdered metal parts is best done in the direction of the shortest extension of the piece, to avoid too great a loss of pressing force through internal [ ] friction. As long as curved surfaces, recesses, or offsets occur only parallel to this shortest axis of pressure, no special difficulties arise: the cross sections, perpendicular to the pressure, do not vary, nor does the shape of the parts change during compression except for a gradually reduced thickness (Fig. IA). The problem becomes more difficult, however, when the curved surfaces or recesses are perpendicular to the shortest axis of the part (Fig. IB). Two processes for molding uniformly dense parts with complicated shapes from powdered metals are described in detail in this paper. Both can be employed successfully by those trained in the art. The first refers to curved parts; the second is especially adapted to parts having one or more recesses or steps. Both methods, as set forth here, are applied under the condition that presents the more difficult problem. For clarity, before description of the two practical methods, the variable factors in molding powdered metal parts will be reviewed, then an idealized procedure will be considered briefly. VARIABLE FACTORS IN MOLDING POWDERED METAL PARTS Compression Ratio Compression ratio is defined as the proportion of the final relative density of the compact to the apparent density of the powder. For iron powder of an apparent density of 3.0, for example, a compression ratio of 2 1/2 : I would be required to produce a compressed compact of 7.5 density; whereas for another iron powder having an apparent density of only I.5, a compression ratio of 5:I would be required to produce the same density. The lower the powder's apparent density, the greater must be the compression ratio for pressing compacts of high density.

Jan 1, 1945