Search Documents

By J. A. Ede

The property of the Spring Valley Coal Company, situated in Bureau county, Ill., comprises something more than 30,000 acres of coal-lands, on which have been opened four mines, designated as Nos. 1, 2, 3 and 4. Figs. 1, 2, 3 and 4 are plans of the first three; and Fig. 7 is a view of the surface-plant at No. 4, the workings of which it is not necessary to illustrate, as this mine has been practically merged in No. 2. No. 4 shaft is only 500 feet from No. 2, and both are ventilated by the same fan, and are in the same circle of air-supply. In speaking of No. 2, we now include No. 4. The system pursued in all the mines is " long-wall advancing," and the shafts are all vertical. The seam worked is locally and commercially known, in the Illinois series, as No. 3; but its position in the geological series is that of No. 2. It averages in thickness about 42 inches, arid has no partings, but mines in rectangular lumps, which stand a large amount of handling before breaking. An analysis made from Colliery No. 1 gave the following : Per cent. Moisture,.......... 1.45 Volatile combustible matter,.47.27 Fixed carbon,.........41.97 Sulphur,.........2.46 Ash,....... .. .. .. 6.85 Plate 6 shows a photographic view of this seam. The staff seen in the view is 37 inches long. The table on page 188, recorded in my office, which I presume to be correct, may be of interest. The bottom is fire-clay, varying in thickness from 6 to 24 inches. It affords what is considered good mining-ground. The roof immediately above the coal is a dark shale, lying in small bands, from 4 to 9 inches in thickness. Between the

Jan 1, 1900

By S. L. Couling, D. J-P. Adenis

i2) twinning in poly crystalline magnesium does not usually occur homogeneously but is concentrated in localized regions or bands inclined at about 45 deg to the stress axis. These bands of twinning are in many ways similar to the Luders bands seen in mild steel alzd Al-Mg alloys. Within a hand the percentage of the volume twinned may approach 100 with no twinning outside the band. Bands are not produced in specimens of grain size a3 x 10-= in. or in samples deformed at temperatures 300°F. Annealing of heavily twinned regions leads to re crystallization textures markedly different from those found in the starting material. The exact preferred orientation appears to depend on the starting grain size, the amount of compres-sive strain and the manner in which it is introduced. MAGNESIUM, with its hexagonal crystal structure, deforms plastically at room temperature by a variety of deformation mechanisms, one of the most important of which is (1012) twinning. In single crystals such twinning occurs on compression parallel to the basal plane or tension perpendicular to it. In wrought polycrystalline magnesium, such as rolled sheet, the preferred orientation is such that almost all the grains have their basal planes nearly parallel to the sheet surface. Therefore, if sheet material is deformed by cold rolling or by tension in the plane of the sheet, deformation of the grains by (1012) twinning is not favored. On the other hand, twins form readily on compression parallel to the plane of the sheet as in a compression test, on the compression side of a bent sample, or at the outer rim of a drawn cup. The first part of this paper deals with the morphology of (1012) twinning in polycrystalline magnesium. Some aspects of this subject were covered by Barrett and ~aller.' Of direct bearing on the work to be reported here are the comments of Jetter' in discussion to Ref. 1. He shows that Mg + 1.5 pct Mn alloy sheet when bent about a transverse axis develops a pattern of transverse bands on the surface of compression. A longitudinal section through the sheet shows that the bands are wedge-shaped and inclined to the rolling direction. The bands were identified as "outcrops of regions in which deformation is localized as the result of the reorientation brought about by (1012) twinning". The second part of the paper treats the recrys-tallization texture of the specimens twinned by compression. Magnesium deformed and then annealed generally recrystallizes with no change in orientation.1'3'4 This statement is true provided that the amount of (1012) twinning occurring during deformation is small. In an isolated observation, Anse15 has shown that, when deformation produces much (1072) twinning, annealing causes new maxima to appear in the pole figure. The second part of the paper elaborates on this point. I) MATERIALS AND PROCEDURES All of the experimental work to be reported was done using the commercial sheet and plate alloy AZ31B (nominal composition: 3 pct Al, 1 pct Zn, 0.4 pct Mn, balance magnesium). This alloy is available commercially in two tempers, -0 (fully annealed) and -H24 (partially annealed), and specimens of both tempers were used in various experiments. The average grain. diameter (AGD) for -0 temper 0.125-in. sheet is about 0.5 x 10- in.; where material of larger grain size was desired, anneals at elevated temperature were used to grow the grains. compression tests were made on a screw-driven "hard" machine. The specimens were clamped in a

Jan 1, 1964

By Falih Ergunalp

REGULAR production of chrome in Turkey started in 1860 with the operation of the Bursa deposits (5, Fig. I). Others were discovered at Makri, near Fethiye (3, Fig. I). For 33 years Turkey remained the principal source of this mineral. While new discoveries were coming in elsewhere, Turkey's output declined until 1921, as a result of four successive wars, which ruined the economics of the country. In 1927 a revival came with the production of 18,000 tons. In that year the Société Minière de Fethiye was formed. This company now operates mines in the Vilayets of Aydin, Denizli, Burdur and Mentese, and it has reached a maximum production of between 80,000 and 90,000 tons annually. The Turkish output therefore increased from 29,000 tons in 1930 to 55,000 tons in 1931; and to 119,009 tons in 1934. The second phase in the increase in chrome production in Turkey came about in 1935, when the Government decided to reorganize and control the mineral industry of the country according to the principles of "government control" of the present regime. Up to that time the mineral resources of the country had been exploited by private concerns. In 1935, the M.T.A. (Maden Tetkik ve Arama) Institute (Institute of Mining Research and Geological Survey) was established by the Government to do the geological and geophysical survey work and discover new mineral resources for the country. Before the establishment of the M.T.A. Institute, the chief chrome-producing region was Fethiye (3 and 4, Fig. I). As a result of the extensive work of this bureau, many new chrome deposits have been discovered and are now in production. The operational field of the mineral industry was given to Eti Bank, another Government-sponsored and Government-controlled establishment. Eti Bank gradually took over the exploitation of existing mines by purchasing them from privately operated companies. Attention was first given to the Zonguldak collieries and to the different chrome deposits scattered over the country. The Guleman mines (14, Fig. 1) were developed and put in operation in 1936. Since then the bulk of Turkish chrome output has come from this mine, which yields the highest grade ore in the world (averaging 52 per cent Cr2O3). In 1939, the recently discovered chrome deposits to the north of Eskisehir went into production, yielding ore having a Cr2O3 content of 51 to 52 per cent. Today, more than ever, the efforts of both the M.T.A. Institute and the Eti Bank are concentrated on finding new deposits and placing them in operation. There are still many promising regions of the country that merit systematic surveying and prospecting for chrome ores. Thus it is probable that Turkey will continue to make noteworthy progress in chrome output. As the annual chrome production of

Jan 1, 1944

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by [P OL, plotting So = Ao as a function of eo = Lo] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors' It was shown that the true physical behavior of the material in the tension test could best be represented [by plotting the average true stress, S = P as a function of e = q' = log o = log Log] where P, A, L, S, e, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such- curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

By Robert Archer

THE proper material of construction for a given purpose is that material which meets the requirements satisfactorily at the lowest ultimate cost. It is consistent with this principle that most aluminum castings are made of an alloy containing about 8 per cent. copper. This alloy possesses mechanical properties satisfactory for general engineering purposes together with manufacturing characteristics leading to the production of finished castings at low cost. It is to the aluminum industry what gray iron is to the iron and steel industry. Just as some services require "semi-steel," malleable castings or steel castings instead of gray iron, there is a certain and growing demand for aluminum castings of superior strength or ductility, or both. Since the beginning of the industry producers and others have sought to develop alloys or processes by which such castings could be made. Out of these efforts have emerged many alloy compositions and special processes, of which only a few have had sufficient merit to survive. It is the purpose of this paper to describe those which seem to the authors to offer the greatest promise for the production on a commercial scale of aluminum castings of superior mechanical properties, with special reference to heat-treated castings. The suitability of an alloy or process for actual manufacture is affected by so many factors that the problem of appraisal is not a simple one. Since this is such an important part of the whole subject it is proposed to discuss briefly some of the requirements. The final verdict is of course the result of commercial trial and experience. It will therefore, perhaps, be profitable to employ a somewhat historical method of treatment in discussing the subject of alloy development.

Jan 9, 1926

By Charles Law McCabe, Lyndon H. Everett, Edna A. Dancy

It has been found that the carbide phase present at equilibrium in the system M-H2-CH4, at about 600°C, is MC for the rare-earth metals Ce and Pr. X-ray diffraction analysis showed that the monocarbides have fcc structures with lattice constants of 5.036 + 0.009Å and 5.131 + 0.001Å for CeC and PrC respectively. Gaseous equilibrium measurements were used to calculate the standard free energy of formation of the monocarbides from the elements. for the formation of (+ 1300) for the formation of PrC. THE rare-earthdicarbides, and their crystal structures, have been known for some years,l but only more recently were the carbides CeC,2,3 Ce2C3 2 and CeCS3 reported. In 1958 to 1959, Spedding et al. published work on the lanthanum-carbon system4 and other rare-earth metal-carbon systems,5 proving the existence of M2C3 and MC2, and measuring the lattice constants. They also demonstrated that tri-rare earth carbides, M3C, exist for the rare-earth metals samarium through ytterbium. However, they concluded that the cerium monocarbide reported by Brewer and Krikorian2 and by Warf,3 and given a fcc structure with a lattice constant of 5.130Å bythe former workers, was, in fact, cerium metal with carbon dissolved in it. They were also unable to find any evidence for the existence of Warf's CeC3, for which no structural details had been given. Even more recently, Palenik22 reported the existence of only M2C3 and MC2, having been unable to find any evidence for the existence of any other rare-earth carbides. There are no published experimentally derived thermodynamic data for the formation of any of these carbides, although Brewer and Krikorian6 have estimated values of for CeC, Ce2C3 and CeC2. The objective of the present investigation was; to determine experimentally the free energy of formation of any of the reported carbides of cerium and praseodymium, through a study of the rare-earth metal-hydrogen equilibrium. EXPERIMENTAL A methane-hydrogen mixture was circulated, in a closed system over previously prepared cerium or praseodymium hydride, and when equilibrium had been attained, the gas mixture was analyzed by selectively oxidizing the hydrogen and condensing out the water formed. The metal hydrides were used as starting material for convenience because, otherwise, the hydrogen in the gas mixture would immediately dissolve in the metals; in addition, the metals would not react with methane alone at the experimental temperature (around 600°C). The circulating system was based on that used by Browning, DeWitt, and Emmett7 for similar studies on iron carbides. It consisted of a quartz reaction vessel, all-glass circulating pump, analysis tube containing copper oxide that could be heated to 300" C by means of a small furnace, a solid CO2-methanol trap, and a double limb absolute manometer, Fig. 1. A cathetometer, capable of reading to 0.005 cm, was used to measure the difference in height between the two columns of mercury. In its final form, the reaction vessel was enclosed in an outer jacket, containing approximately the same pressure of hydrogen as that within, to reduce errors due to diffusion of hydrogen out through the fused silica of the reaction vessel., The circulating system was supplied with

Jan 1, 1962

By Carlton Beal

This paper presents useful charts for conversion of various viscosimeter units into centipoises and graphically summarizes published investigations of the viscosity of air, water and natural gas at high temperatures and pressures. Where possible, charts and correlations were constructed to cover a range of temperature (60°F. to 300°F.) and pressure (14.7 lb. per sq. in. abs. to 8000 lb. per sq. in. gauge) encountered in oil fields. Correlation charts, for the purpose of predicting crude oil viscosity and solubility behavior at oil field temperatures and pressures, were constructed from an analysis and correlation of 1332 viscosity and solubility observations from 953 crude oil samples taken from 747 oil fields. Of these fields, 501 are in the United States, including 75 in California. Of the 1332 observations, 1215 were viscosity values, including 786 of gas-free crude oil, 351 of oil saturated with gas, and 78 under-saturated with gas at pressures above the bubble point. Results show that crude oil viscosity at various reservoir conditions can be predicted with average deviations varying from 24.2 per cent for gas-free crude oil to as little as 2.7 per cent for undersaturated crude oil "above the bubble point." The solubility of crude oil may be predicted from oil gravity and saturation pressure with an average deviation of 22.0 per cent from observed values. In conclusion, it is shown that the viscosity of a gas and gas-saturated crude oil may be predicted within the accuracy of most reservoir computations. Viscosity is a measure of flow resistance; common units are in centipoises (cp.). The object of this report is to present conversion charts and simplified 'correlation charts showing the viscosity behavior of air, water, gas and crude oil and gas-saturated crude oil under oil field temperatures and pressures, which have been known to be as high as 300°F. and 8000 Ib. per sq. in. gauge under subsurface conditions. The viscosity of a liquid or gas is important because it is a measure of its fluidity, or its ability to flow through pipe lines or oil sands. Viscosity of air has become important because it is being used in secondaryl,2 recovery projects. The viscosity of natural gas and water at reservoir conditions is useful because they are almost universally associated and produced with crude oil. The viscosity of gas-saturated crude oil at reservoir pressures and tem peratures is of particular value in making estimates of oil reserves3 and rate of oil recovery from flush pools when production decline data are limited. Instruments Used to MeasuRe Viscosity There are many types of viscosimeters,4 and the instruments most commonly used to measure the atmospheric viscosity of liquids at moderate temperatures and their practical working ranges have been deScribed5,6 in detail. Fig. I and Fig. 2 are viscosity conversion charts which have

Jan 1, 1946

By J. H. Carpenter

LMENITE, rutile, zircon, and other heavy minerals are found in small amounts in the sand that covers most of Florida. Small enriched deposits occur on the beaches and coastal dunes. One beach deposit east of Jacksonville was worked during World War I and another near Vero Beach during World War 11. Both ceased operation when the resumption of imports reduced prices. Early in World War II reduction of rutile imports made a domestic source of the mineral necessary to maintain the expansion of armaments. Explorations made near Jacksonville discovered a relatively large body of low-grade ore about 10 miles inland from the beaches. A plant installed by Rutile Mining Co. of Florida using both flotation and tables encountered difficulties because of low plant capacity and organic slimes in the ore. In 1944 Humphreys Gold Corp. solved the problem of concentrating the low-grade ore by using the newly developed Humphreys spiral concentrator and by mining with a hydraulic dredge. This combination of low cost mining and concentration permitted the plant to continue operation in competition with foreign ores when imports were resumed following the war. The success of the Jacksonville operation renewed interest in Florida as a source of titanium. An extensive survey of the state was made by E. I. du Pont de Nemours and Co., Inc., under the direction of J. L. Gillson in 1945 to 1946. Sampling was carried on by drive pipe drilling to depths of 20 to 25 ft. Encouraging values were discovered near the location of the present Trail Ridge mine, 50 miles southwest of Jacksonville, near the town of Starke. The United States Bureau of Mines was interested in exploring for heavy minerals in Florida, and on the recommendation of both the state geologist of Florida and of Du Pont geologists, drilled deeper where marginal indications were found on Trail Ridge. In 1947 it was discovered that sufficiently higher values occurred at depth to make the deposit commercial. The orebody at Trail Ridge is a long sand deposit averaging about 1 mile in width and 35 ft in depth. It is approximately 1 1/2 miles wide at the north end of the portion now being worked, tapering to a blunt point 3 miles to the south. The ore reaches a maximum depth of 65 ft near the center and feathers out into barren sand at the edges. The ground surface is relatively flat and is covered with vegetation including pine, scrub oak, palmetto, and occasionally in swampy areas, cypress. The remain of a dense woody growth underlies and marks the bottom of the Ore 'One. It is difficult to drill through this layer, but in some cases where it is less than 5 ft thick it has been possible to drive through the wood. Sand lying below is coarser than that in the ore zone and contains no values. The wood layer consists of unconsolidated carbonized fragments of branches and other forest trash associated with a considerable amount of ar-

Jan 1, 1954

Jan 1, 1967

By P. V. Martin

Shortly after the middle of the nineteenth century, the invention of the regenerative open-hearth furnace and the development of the Bessemer process stimulated a rate of steel production whose magnitude created an unprecedented demand for pig iron. Revolutionary improvements in furnace design, auxiliary equipment, and operating technique enabled the blast furnace to keep abreast of the constantly increasing requirements of the steel mill. The development of improved blowing equipment, more adequate facilities for material handling, and particularly the general use of anthracitc and coke to replace the physically weaker charcoal, led to a rapid expansion in both the height and volume of furnaces. Beyond a doubt, however, the greatest single factor in blast-furnace improvement at this time was the use of the higher blast temperatures made available by the replacement of the recuperative iron pipe stoves by the regenerative Cowper brick stove. The increased blast temperature not only resulted in greater output but also reduced fuel consumption . far more than could be explained by the additional heat content of the blast. The progress of iron manufacturing was thus largely mechanical and thermal. Little attention was given the chemistry of the process until the publication of the investigations of Sir Lowthian Bell.1 Bell's painstaking experiments and investigations gave to the blast-furnace man his first real scientific conception of blast-furnace chemistry. Bell's recognition of the dual function of the carbon, the technical importance of reversible reactions and chemical equilibria, and his conception of the degree of oxidation of the carbon as shown by the analysis of the outgoing gases as a criterion of furnace efficiency, laid the foundation upon which has since been erected the structure of blast-furnace theory. Prominent among those availing themselves of Bell's data as .a basis of further study was M. L. Gruner,2 professor of the French School of Mines. His "Blast Furnace Phenomena," published in 1870, presented

Jan 1, 1940

By Benjamin Talbot

(New York Meeting, February 1913.) THE problem of segregation and cavities in steel ingots is a subject which has given and is still giving metallurgists, en¬gineers, and operators matter for serious consideration.. This question has come more into prominence lately in the United States, clue largely to the desire of railroad engineers to secure a better rail than they have obtained in the past, as the service they demand is increasing in severity; and no doubt manufacturers will be able to meet what is required of them. The rails here are as good as those made in other countries, but the conditions of service and the extremes of climate are more severe and consequently more breakages occur. Various reasons have been advanced to explain why rails may not be as good in quality to-clay as in the past. Some engineers consider that modern methods of manufacturing, designed chiefly to obtain large output, tend to reduce the standard of excellence of more deliberate methods. Others think that 4-ton ingots are worse than those of 2 tons. Again, it is .stated that the 100-ton heat in one ladle is too large, and is a :step in the wrong direction in casting. My experience upon the question of the size of the ingot is that in rolling rails of from 85-to 100-lb. sections, the range of ingot is only practically such that the difference in the size does not help in the question of segregation, cavities, or blow-holes.

Jan 4, 1913

By John V. Beall

Hard as the Revett quartzite are conditions governing the deep mines of the Coeur d'Al6ne. In fourscore years of mining, heat and pressure have been the rewards of preseverance. Such obstacles are the natural concommitant to search for ore at depth. But high cost and shortage of miners is a creeping frustration of the decade. These grim observations were made on a trip to the mines of the Coeur d'Al6ne in the first week of May. But the bouncy optimism of competent mining engineers and geologists overrides by far the tough conditions. This is the story of what they are doing. I think they are setting the stage for the wonder mines of tomorrow. I didn't meet all the people or see all the mines, so there are unfortunate gaps in the story. Then too, sometimes the muck and water blotched my notes, or I couldn't write fast enough or I was too tired. No matter. There is much to tell and, because it is basically a human story, I am flouting the rules of technical journalism and couching it in the neglected "I" person. First then, a little history . . . .

Jan 7, 1966

By Thomas A. Read

The internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of ioo when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose—that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals mill be presented. Experimental Procedure The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrcment A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders M in. in diameter and I 1/2 to 21/2 in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler's saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is 1/4 in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By H. F. Perkins

CORROSION as an economic problem is growing rapidly in importance not only because it entails a replacement of corroded parts, but because it interrupts operation and causes hazards of damage and injury through failures of corroded equipment. Nearly all industries are interested in this subject. This paper, although concerned chiefly with corrosion in a complete refinery on the sea coast, discusses many of the various forms of chemical decomposition, most of which are found universally. The petroleum refining industry, in the writer's opinion, is seriously afflicted by the presence of sulfur in nearly all crude oils. The complete removal of sulfur from the crude as it enters the plant would cause such a relief from corrosion that this problem for research would seem to demand active attention. Next to sulfur the most troublesome corrosive agent is the saltmagnesium chloride, found in the water associated with crude oil, the last traces of which are so difficult to remove. This is much less serious, however, than the sulfur. Refinery corrosion can be tabulated as follows: Causes of Corrosion and Places of Attack in a Refinery CORROSIVE ELEMENTS MATERIAL ATTACKED Air: Pipe lines Moisture Tanks COQ Electric fixtures Sulfur gases Still towers Chlorine Condenser boxes Other acid-forming gases Ladders and stairs Smoke stacks Steel buildings All exposed metal Water: Alkali Fire lines and hydrants Acids Cooling water lines Air Condensers and coolers Other dissolved gases Boiler tubes Steam Steam pipes and valves Turbines Oil Sulfur compounds Tanks, pipes, valves, stills, towers MgCl2-Hydrochloric acid Condensers Air contamination

Jan 12, 1926

By Noel Jarrett, Allen S. Russell, Bernard M. Starner, Stanley C. Jacobs

A process has been developed to refine high-grade commercial aluminum to 99.99 pct purity. This enzploys precipitating titanium, vanadium, and zirconiu~ as borides. The upgraded liquid is partially crystallized under conditions that prevent massive freezing. The resulting crystals are compacted and washed free of adhernig impure liquid aluminum by melting the top crystals while draining off the liquid. Finally, the bottorn portion of the crystal bed is melted and removed as the pure product. Leakage from the crystallizat~on vessel is prevented by a layer of alumina granules that are not wetted by the aluminum. ALUMINUM of 99.99 pct purity is desired in a variety of applications. These include electrolytic capacitors, catalyst carriers, decorative trim for automobiles, aluminum powder, and high-strength alloys. This market was for many years filled by refining commercial-purity aluminum in a three-liquid-layer electrolytic cell of the type originally proposed by Hoopes. To meet the expanding need for lower-cost high-purity aluminum, a refining process based on chemical precipitation and fractional crystallization was developed. The availability of this super-purity metal was announced in November 1961, and three patents1-3 relating to the process were issued in 1965. An alternate process, comprising continuous fractional crystallization of a portion of a liquid-aluminum feed stream under conditions of strong agitation at the surface of the growing crystals, was published by Dewey4 in 1965. Earlier proposals by Larsen 5 and by Regner6 also emphasized the advantage of rapid agitation of the melt in the region of the crystallization zone. johnson 7 more recently proposed extracting purified aluminum from an alloy by mixing crystals of pure aluminum into the molten alloy, allowing them to grow, and removing the pure aluminum as by casting. Aamot's 8 recent patent describes a freeze refining process that involves controlled partial freezing against cooled moving retort walls. The Alcoa process to produce high-purity aluminum is schematically described in Fig. 1. Relatively pure aluminum is treated with boron in a furnace (a) to precipitate high melting point impurities, the supernatant liquid is transferred to a crystallization vessel (b), the liquid is partially crystallized with mechanized "tamping" (c), the remaining impure liquid is tapped out and the crystal bed partially and directionally re-melted to wash the underlying crystals (d), and the balance of the crystals is melted and withdrawn as high-purity aluminum (e). PRINCIPLES OF FRACTIONAL CRYSTALLIZATION Commonly encountered impurity elements form two types of systems with aluminum. Titanium, vanadium, and some other transition elements in periodic groups IV, V, and VI are the high melting point impurities. Initial solidification of aluminum containing small percentages of these elements will produce solid markedly enriched in them at temperatures slightly above the freezing point of high-purity aluminum. Most other elements, such as silicon and iron, produce eutectic type reactions with aluminum. In this case the first solid formed on initial solidification at temperatures slightly below the freezing point for high-purity aluminum is markedly depleted while the remaining liquid is enriched in these elements. The equilibrium change in composition during solidification of aluminum contaminated with silicon, iron, or titanium is illustrated in Fig. 2. Here, for clarity, the temperature scale is expanded beyond the

Jan 1, 1968

By W. A. McCurdy, Joseph W. Leonard, T. S. Spicer

INTRODUCTION by T. S. SPICER and J. W. LEONARD Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is process design, operation and maintenance to produce an acceptable product which can be sold at the greatest possible profit. Because of these interests, attention to the unrealized potential value of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of both the product as well as the tributary coal flow moving through a modem coal preparation plant. Thus, coal types having similar physical and chemical properties tend to become increasingly concentrated according to size, specific gravity and/or surface chemistry. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches which are sandwiched together in layers and which visually differ from each other by physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, six percentage points of dry volatile matter and 10 percentage points of total sulfur.1 Similar wide variations exist for calorific value, seam moisture content and undoubtedly, for any other conceivable coal test parameter which might be used for comparative purposes. These observations all point to the long established fact that coal is not homogeneous as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance. Since both coal and associated minerals entering a preparation plant are highly heterogeneous, a multi-product potential beginning with certain flotation cell concentrates and ending with plant refuse may exist. Such a potential can and to a limited extent is achieved at some operations by drawing off coal according to size, specific gravity and/or surface chemistry differences from individual coal cleaning processes. Such a sequenced draw-off of coal of increasing ash increments could yield, among other products, chemical coals, coking coals, coals for pulverized fuel boilers, cyclone boiler coals, coals for cement plants, limestone, shale and clay. Basis for Coal Evaluation and Selection Despite the known heterogeneity of coal, the final analysis of a given coal product is customarily reported as a single average since coal has always

Jan 1, 1968

By H. E. Wilborg, G. V. Henderson

This chapter deals with those sands employed by foundries for the manufacture of cores and molds used in the casting of such common metals as steel, gray iron, ductile iron, aluminum-based alloys, and copper-based alloys. Most metal is cast in "green sand" molds in which the sand mixture, consisting primarily of silica, clay, and water, forms a plastic material. This plastic material is rammed around a pattern in a split box called a flask, then the box is separated, the pattern is withdrawn, and the metal is poured. These green sand molds are broken apart when the metal has solidified. The sand is then remixed and a new mold made for the next casting. To a lesser extent silica sand is mixed with resins or oils and, after forming, the mixture is hardened by either heat or chemical reaction. In any case, the foundry mold or core is used just once before being broken up and remixed for manufacturing another core or mold. By far the greatest consumption in the foundry is of those types of sand high in silica, low in clay (under 0.5%), and occurring in numerous locations thoughout the United States. Consumption End Uses Foundry sands fall into four distinct categories: silica sand, lake sand, bank sand, and natural molding sand. Silica sand is a general term used to describe washed, graded, dried, and cooled clay-free sands which are found in many parts of the United States. They generally contain 90 to 100% silica but vary greatly in chemical analysis and grain structure. Lake sand is the sand dredged from Lake Michigan or dug from the dunes bordering that lake. Bank sand is composed primarily of silica grain but containing up to 5% clay. It is shipped in both the damp and dry state but the normal processing of bank sand consists only of drying and scalping. Occasionally two different grades of bank sand are blended prior to or during loading. Natural molding sand is a term used to describe a sand containing sufficient clay as mined to be suitable for molding purposes. Clay content may vary from 10 to 24% with the balance of the material consisting primarily of silica sand. These sands range in fineness from one peaked on the 20 mesh to one which contains more than 50% of the particles passing the 270 mesh. Lake sands are relatively coarse and are used in great quantities for the production of automotive castings. Bank sands and natural molding sands are gradually phasing out as the production of castings becomes more a science and less an art. The vast majority of foundry sands used today are those known as the silica sands and lake sands. Foundry sands are used in two basic ways. The majority are used in the green or uncured state with the balance used in the cured or set state. Green sand is grain bonded with clay and contains varying amounts of water to plasticize the clay in order to bond the grains together. Green sand is either naturally bonded or "synthetic" sand. The naturally bonded molding sands are generally found in the Hudson River Valley of New York State, Cumberland County in New Jersey, and in Tennessee and Mississippi. Synthetic sand is molding sand compounded in the individual foundry. It is made up primarily of graded silica sand, western or southern bentonite, water, and carbonaceous and/or cellulosic materials. Green sand is used primarily in making molds. The use of naturally bonded green sand has been declining for many years, primarily because naturally bonded sands are more difficult for the foundryman to find and control. Synthetic green sand, on the other hand, can be

Jan 1, 1983

By Robert D. Pehlke, Kazuhisa Okajima

The activity of zinc in dilute liquid lead alloys containing small additions of silver and gold has been measured using a multielectrode galvanic cell with a fused chloride salt electrolyte. The range of temperatures studied in the Pb-Zn-Ag system was 550" to 670°C and in the Pb-Zn-Au system was 680" to 800°C. The interaction parameters between zinc and the precious metals in the respective temperature ranges are ThE lead-rich corners of the Pb-Zn-Ag and Pb-Zn-Au ternary systems are of considerable industrial importance. The use of zinc additions for the desilvering The results of this investigation have Provided a senzi-quantitative determination of the liquidus phase boundaries in the lead-rich corner of these ternary diagrams. of liquid lead either by the Parkes process or by the more recent Williams continuous process is an important refining phase of lead production.1 Several in-ve~ti~ations~-~ have been carried out on the Pb-Zn-Ag system with the hope of improving the efficiency of refining lead in this manner. The addition of zinc also provides a means for separating gold from lead. Since gold is eliminated more easily than silver, a two-stage removal of gold and silver is possible.8'7 The thermodynamic interactions between zinc and these precious metals in dilute solution in liquid lead

Jan 1, 1968

By H. H. Kaveler

Education is for the purpose of developing citizenship, and, if it is pursued for the additional purpose of preparing for a professional career, such as engineering, it is also directed to developing a knowledge of essential science, aptitude for the application of science to practical situations, and a knowledge of the industrial art in which the engineer will be engaged. The process of education required for engineering must of necessity extend beyond the classroom into industry. For that reason, the education of engineers should be divided as between the university and industry. Specialization in engineering should logically come as a result of experience in an industry. The student cannot take the time in a university, and, the university cannot teach the skills required to develop a specialist without sacrifice to the more essential broad purposes of formal education. In addition to talent in science, aptitude in the application of scientific fact, and knowledge of the industrial art, the engineer should possess certain personal qualities which are helpful in the pursuit of a professional career. Those personal qualities are: the ability to work as a partner in an enterprise, the ability to do jobs in a way whereby job performance is a means of gaining experience and increased responsibility, the capacity to write and speak in an understandable manner, and, a Proper regard for the "significance of answers." These pcrsOnal qualities may be of almost equal importance to acabemic accomplishments in the field of science. Development of such personal qualities are an essential part of the student's training in the university and in industry. They can be developed effectively through the leadership of instructors. Compulsory Education Nature played a mean trick On the human race when the evolutionary Process failed to develop in the individual a capacity to inherit knowledge. Were knowledge transmissible in a cumulative manner from generation to generation, mankind would be by inheritance wise beyond measure within a few generations. Then there would be little if any need for a "system of education." As matters stand, however, all must suffer the burden of starting life at the "zero " level of learning from which station each rises depending upon individual capacity to assimilate knowledge left of record by our predecessors and the individual effort exerted to compensate for Nature's failure to endow the offspring with intelligence. In the United States some degree of education is generally regarded as essential and necessary. Therefore, all citizens are subjected by law to an educational process covering the primary school age from six to sixteen years. Beyond the schooling required by law, many attend secondary schools, and beyond that, schools of higher learning. Our standard of living is at a level that permits an increasingly large fraction of the population the opportunity to go through all of the formal educational process. As a result, education in the colleges and universities has almost reached a mass production level. In spite of the high

Jan 1, 1949