Search Documents

By S Tjerry, S Szylkarski, B Willis-Jones, I Dubinski

Achieving relinquishment of mining sites is becoming increasingly difficult, with a study by Byrne (2013) estimating that out of a set of 73 mining and metals sites around the world, less than ten per cent had achieved relinquishment over the last 50 years. The median forecast duration of time allocated for water management in the closure plans studied was approximately ten years, while the reality at the actual sites was a median duration of 22 years to date and growing.One of many challenges in mine closure planning is managing geomorphic stability of stream diversions. The challenge is to be able to demonstrate to regulators and the community that a proposed rehabilitation solution will be stable over the long term.During the mining operations, local watercourses and surface drainage can be diverted and managed using engineered channels and drainage structures. However, during the post-operations stage, the engineered channel and drainage may require modification to a more natural condition that will facilitate long-term environmental sustainability. Achieving geomorphic stability of a diverted watercourse is difficult, with the majority of stream diversions in Australia failing to meet expected design performance (White et al, 2013). Geomorphic stability is a complex process that is controlled by a combination of factors, including hydraulic flow conditions, geotechnical conditions and vegetation.This paper proposes that a fully dynamic and deterministic geomorphological model can be used to supplement the traditional empirical approaches to assess long-term geomorphic stability. The paper provides an overview of the geomorphological models and how they have been applied in engineering studies for forecasting future evolution of stream systems. The paper discusses the potential application of these models in the mining industry for forecasting and optimising surface water structures for the operations and post-operations stages of the mining cycle.CITATION:Szylkarski, S, Willis-Jones, B, Tjerry, S and Dubinski, I, 2016. Improving the reliability of stream diversion designs in mine closure plans using a morphological tool, in Proceedings Life-of-Mine 2016 Conference, pp 212–215 (The Australasian Institute of Mining and Metallurgy: Melbourne)

Jun 28, 2016

By Moorrees C, Everson P

A detailed examination of carbonic acid leaching of crude iron-containing magnesia derived from Savage River magnesite shows that the rate and extent of magnesium and iron dissolution are affected by the slake time, leaching temperature, carbon dioxide pressure, pulp density and rate of agitation. In order to produce high-purity magnesia from the leachate by precipitation and calcination, the optimum leaching conditions, which are those that yield maximum magnesium and minimum iron dissolution, have to be a compromise in terms of the above parameters. For example, iron dissolution can be limited by leaching at an elevated temperature (-45°C), but because the maximum concentration of magnesium biearbonate decreases rapidly with an increase in temperature, it is necessary to use a low pulp density (-2 per cent solids) in order to achieve an acceptable degree of magnesium dissolution.Evidence is obtained that iron dissolution involves the formation of a soluble ferric bicarbonate complex that decomposes at elevated temperatures. The extent of iron dissolution is much higher than might be expected and it is probably because the original magnesite contains siderite in solid solution with the magnesite; on calcination, the hematite whieh is formed is in a very finely divided condition and hence more reactive.

Jan 1, 1983

A device is described which is suitable for the automatic sampling of dust in dust laden flue gases. This device, called a Venturi Sampler, consists of two pipes each fitted with a suitably designed venturi.Both pipes are placed in the flue where one acts as an open-ended reference tube and the other as the actual sampling tube.The gas sampling rate is automatically controlled so as to maintain a zero differential pressure between pressure tappings in the two venturi throats. The venturies are so designed that under these conditions the gas velocity in the sampling pipe is always equal to the free gas velocity in the flue-that is isokinetfc sampling conditions are maintained.INTRODUCTIONThere is a constant need in industry for regular and accurate assessments of dust losses, both to assist in improving operating efficiencies in order to minimize losses, and to obtain accurate metallurgical balances. In many cases where sampling is carried out in dust laden gases, the existing sampling methods are both laborious and inaccurate, and often make no provision for changes in flue gas velocity while sampling is in progress.In the majority of cases where a measurement of dust losses in a stack or flue is required, a preliminary velocity survey is made with a pitot tube to establish the gas velocity at each of the points at which samples are to be taken. The sample of gas (and dust) is withdrawn through a tube connected via a flowmeter to an exhausting apparatus. Some means of removing the dust from the gas sample is placed in circuit ahead of the exhausting apparatus. This is often an alundum or paper thimble housed in a gas-tight container.The purpose of the flowmeter is to measure the actual flow of gas during sampling so that the sampling velocity at the inlet to the sampling tube may be calculated, and the flow corrected so that the sampling velocity will agree with...

Jan 1, 1959

By M Stewart

The structural framework for the major gold deposits of the Reefton Goldfield was largely established in the 1930s after a detailed regional geological mapping programme. Recent new mapping has now substantially modified the structural framework of the Globe Hill - Devils Creek area and the Waiuta area. Using bedding-cleavage vergence as a method of establishing fold limb facing, many new fold structures have been identified, some of which conflict with long-established structures such as the Globe Hill and Waiuta anticlines. In addition, the mapping of areas of west- versus east-facing limbs constrains the position of many faults. The mineralised Globe-Progress Shear is one such fault which graphically demonstrates major structural discordance of the folds in the hangingwall compared to the footwall. Recognition of the folding is establishing the structural framework for understanding of the origin of these productive gold mining areas.

Jan 1, 1996

By J Rutter, D La Rosa, P Walters, M Scott, L Keeney

Bulk ore sorting technologies, whether surfaced based or penetrative, have seen an increased uptake by the mining industry for preconcentration application. As with all technologies, going through the technology validation process is key to de-risking the operationalisation of the technologies and to demonstrate and confirm predicted value propositions. The ability to laboratory calibrate cross-belt bulk sensors is standard practise for sensor vendors, however transitioning the technology from laboratory to real-world application is a non-trivial process. The industry has taken two main approaches to trialling and validating bulk sensing technologies in operational environments, namely:  Construct an off-line pilot facility at scale, or  Install bulk sensing systems on production conveyors Each of these two approaches have significant advantages and disadvantages and require different experimental design programs and analysis methodologies. Consideration of material movement, heterogeneity degradation, logistical requirements, and financial investment all factor into which approach is most suitable for an evaluation scenario. CRC ORE in partnership with mining companies, have conducted several bulk sensor pilot trials utilising different sensor technologies employing each of the two main approaches outlined above. This paper describes the challenges faced, learnings obtained and outlines a position on how to transition bulk sensing technologies from the laboratory into the operating environment. The case studies presented cover a range of commodity types in both open pit and underground operations.

Nov 10, 2020

By J A. Rowland

When executing a ventilation change the mine ventilation circuit is in a state of flux throughout the entire change period with discrete mine areas both under ventilated and/or over ventilated during the change process. Whilst routine risk reduction strategies such as removing electrical power and people from the mine are commonly deployed it is wise to complete the change in the shortest practical time frame. This not only minimises the chance of unacceptable concentrations of contaminants accumulating around the mine but reduces the impedance on production activities which are routinely suspended during these change periods. This paper firstly highlights the importance of the maintenance of an accurate ventilation model and discusses issues which should be considered to assist to maintain in it a suitable state of health. Further it provides some tips on how to monitor that your model is in an acceptable state of tune so that it can be confidently deployed in the change process. Finally, it details the sequential process how a finely tuned and accurate ventilation model can be utilised to carry out major ventilation changes according to appliance pressure adjustments only and without the need to constantly measure and check resultant branch flows throughout the whole change process. Also discussed are some simple practical tips which will help ensure that the ventilation change process will go according to the devised plan on the day and in the most appropriate order including checking the efficiency and accuracy of the change, after it is completed.

Oct 12, 2022

The transgressive sedimentary sequence of the Noumea Basin contains rhyolitic lavas and less voluminous mafic and intermediate volcanics of shoshonitic affinities which erupted simultaneously during the late Cretaceous. The shoshonitic volcanism shows a trend froIn early mafic to younger evolved intermediate lithologies. The rhyolites are consistently calcalkaline. There is no evidence of mixing of the two magma types. The shoshonitic volcanism is the result of a short-lived subduction event related to spreading in the New Caledonia Basin and involved reactivation of an earlier esozoic subduction zone.

Jan 1, 1995

By I Brandes de Roos

Water has played a key role in the Pilbara’s 60-year history of iron ore operations. In contrast to many of the current-day mining environments, iron ore mining was initially hosted by geological formations that were typically above the water table. Such mining operations required no dewatering or dewatering at rates that were less than mine and mining township requirements. The challenge for these operations was not pit dewatering but water supply for mining operations and municipal supply for nascent mining towns.The current industry sees new deposit styles being increasingly targeted, including channel iron and Marra Mamba Formation deposits. These deposits are often lower in the landscape and can require extensive dewatering. Furthermore, increased water demand for ore beneficiation has resulted in major programs of water-supply borefield development. Added to this is the emergence of magnetite projects and their significant levels of water use in ore beneficiation.The large volumes of water that are being extracted to support Pilbara iron ore mining is attracting attention. The Western Australian Department of Water has recently commissioned a study to assess the potential use of surplus mine water as a medium- to long-term supply for irrigated agriculture.This paper outlines the changing landscape of water management in Pilbara iron ore operations and explores strategies for maximising mining productivity. Water management is presented as an enabler for productivity improvements that can potentially provide long-lasting benefits post-closure.CITATION:Brandes de Roos, I, 2015. Shifting waters in the Pilbara’s iron ore industry, in Proceedings Iron Ore 2015, pp 507–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D Syme

In the middle of 2000, BHP Billiton implemented a Six Sigma Plus business improvement program known as Operating Excellence. It was developed based on a business bottom line initiative to deliver 35 - 40c/share and was one of the BHP Billiton strategies to deliver $2 earnings per share and a longer term $40 share price (BHP share price). Cannington is a silver, lead and zinc mine owned and operated by BHP Billiton. Through implementing Six Sigma Plus Cannington wanted to:have in-house capabilities to change and improve; tailor for the needs of each business unit and department; have æSharing of its KnowledgeÆ as a tool for improvement and have a competitive edge across Cannington û to be better than our competitors; learn from and leverage off the successes of improved safety and prior business improvement efforts; and ensure networking and sharing of information have common measurement systems across all assets. As with most business improvement programs û Six Sigma Plus was met with some degree of skepticism, especially given the amount of resources involved. After 18 months, much of this skepticism has been replaced with enthusiasm as peopleÆs understanding and acceptance of its fundamental concepts are being realised. The idea behind Six Sigma Plus is that it combines sound technical solutions with high acceptance by those who need to work with or implement the change. The future vision for Six Sigma Plus is that it become part of what we do at Cannington û just like safety and environment û so that Six Sigma tools and methodologies are used in our every day work.

Jan 1, 2002

By R Hardie, J Crerar, J Merritt, B Kirsch

Longwall mining and related subsidence, and watercourse diversion for surface mining operations have the potential to impact on fluvial geomorphic processes and the health of river systems. This is evident in the Isaac River in central Queensland. The scale and likelihood of these impacts are a function of the extent of existing and proposed mining developments and of the ongoing geomorphic, hydrologic and ecological processes within the Isaac River. Understanding the objectives for the river, the past and ongoing processes at work, the cumulative impacts of longwall mining development and the options for managing those impacts is essential for the development of an effective strategy to manage the health of the river system. An assessment has been undertaken to identify and understand the cumulative impacts of mining subsidence and other mining influences on geomorphic processes and waterway health in the Isaac River over a river length of approximately 100 km near Moranbah in central Queensland. The assessment included the development of a vision and objectives for waterway health. The assessment has identified mining and landuse changes that have impacted on the hydrology, geomorphology, ecology and hence the health of the Isaac River. The assessment has then sought to identify the cumulative impact of longwall mining and related subsidence on current stream condition and the proposed vision for the system. The primary impact of longwall mining on the river was found to be associated with sediment transport. The investigation included assess- ment of total sand available for transport, the volume of sand transported annually and the fluvial process response to subsidence. Recommendations have been developed for the management of the system and for longwall mining to increase system robustness and achieve the river health objectives.

Jan 1, 2009

By D Reid

The engineering properties of soils and tailings often exhibit significant anisotropy. One area where this has been well documents is undrained shear strength. Materials sheared in directions close to the principal stress direction in situ, i.e. triaxial compression, typically exhibit higher undrained strengths than those sheared in other directions such as simple shear. Importantly, along the most common critical failure surfaces relevant to tailings stability, whether primarily through tailings or a critical foundation layer, saturated materials are generally much closer to the simple shear loading direction than triaxial compression. Therefore, testing undrained shear strength of tailings or foundation soils in triaxial compression is likely to result in overestimation of the relevant strengths for design. Although these issues have repeatedly documented in the geotechnical literature for over three decades, they are not appreciated sufficiently across our industry. In an attempt to address and highlight these issues, a review is carried out of historical reference to the importance of simple shear loading. Attention is then drawn to the techniques applied in three recent post-failure investigations, where simple shear testing was applied. Finally, some relevant laboratory test results from a recent project in which the author was involved are outlined.CITATION:Reid, D, 2018. Importance of the simple shear loading direction to the stability of tailings storage facilities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 274–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By R N. Humphries

The aim of this paper is to question the need to develop bespoke monitoring and assessment methodologies and criteria, thereby ‘reinventing the wheel’, when designing and assessing the success of important natural habitat and ecosystem restoration schemes at mine sites in the UK and Australia. It draws attention to the existence and applicability of the Phase I Habitat, National Vegetation Classification (NVC) and Condition Monitoring methods in the UK and similar approaches used in Australia. These are long accepted established methodologies and have published accounts for describing, assessing and managing natural vegetation communities, habitats and ecosystems. They are often used at the environmental impact stage, but seemingly rarely, if at all, in restoration design and management at mine closure. Their application to mine restoration and closure is illustrated and discussed by reference to a surface coalmine in South Wales, UK.It is concluded that the application of a combination of the Phase I Habitat, NVC and Condition Monitoring methods is highly relevant to the expectations of the Convention on Biological Diversity (CBD) and its implementation in the UK, and probably in Australia too. The methodology and criteria described could be incorporated into the guidance and specified in the mining permits so that there is clarity as to the expectations and requirements for monitoring and assessment for bond release. Their use could be of wider application where there is a requirement to assess the success of restored CBD assets and ecosystems.CITATION:Humphries, R N, 2014. Why reinvent the wheel when there are established methodologies to aid the design and assessment of restored natural ecosystems on mined land?, in Proceedings Life-of-Mine 2014 , pp 675–692 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By R J. Butcher

Many deposits have been evaluated as potential block caves over the last 20 years due to the perceived benefit of low operating costs. However, block cave projects are typically capital intensive, with mass mining providing high throughput rates that required large investments in mining, processing and utilities infrastructure. While the key economic metrics in deciding to proceed with a caving project are typically net present value (NPV) or internal rate of return, these may not represent the best decision metrics for some companies. Where a caving project is competing for scarce capital amongst other projects in a company’s portfolio or where the caving project is the only project being evaluated by a company trying to raise capital, other metrics may be more appropriate. This paper explores the use of present value ratio and the minimising of maximum negative cash flow as suitable metrics in determining alternative strategies. Trade-offs between optimising for economic value and capital efficiency measures allow for decision-makers to evaluate potentially higher-risk, higher-capital and maximum NPV projects against lower-risk, lower-capital projects.CITATION:Stewart, C A and Butcher, R J, 2016. Block cave evaluation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 809–816 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D Hillier, A Giblett, K Parker, V Ramsell

Kalgoorlie Consolidation Gold Mines (KCGM) operates the Kalgoorlie Super Pit open cut, Mt Charlotte underground mine, Fimiston process plant and Gidji Roaster facility for joint venture partners Newmont Mining Corporation and Barrick Gold. In 2004, the Fimiston plant was upgraded by the addition of gravity concentration to the Fimiston and Mt Charlotte grinding circuits, including the installation of a central intensive cyanidation reactor to process the gravity concentrates. The gravity project was justified after detailed analysis demonstrating an expected increase in overall gold recovery of approximately one per cent, in addition to reduced elution costs and reduced gold inventory in flotation concentrate stockpiles. The gravity circuits were commissioned in August 2004, and have since consistently recovered 10 to 20 per cent of the gold present in the KCGM ore, delivering a reduction in coarse gold losses equivalent to 0.45 per cent additional metal recovery and contributing to improved metal accountability.CITATION:Giblett, A, Hillier, D, Parker, K and Ramsell, V, 2012. The impact of gravity gold recovery at Kalgoorlie Consolidated Gold Mines, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 199-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Project delivery in our current market is not as efficient as it could be. Industry at large (both client and consultant), is diligently following the engineer, procure, construct, manage (EPCM) or engineer, procure, construct (EPC) delivery models and not necessarily appreciating the underlying principles that make them the effective tools they were to start with. We often misinterpret project management with EPCM and end up with a literal and superficial interpretation instead of the disciplined risk reduction and business value capture exercise it is intended to be. One of these underlying principles is the project team as resource or commodity depending on which perspective we follow. Some of us understand this principle only too well and succumb to the temptation to take advantage of the imbalance in the understanding of EPCM by selling bodies and hours. Value and return on investment do not always come into the equation. The latecomers and aspirants are struggling with this as a barrier of entry into this lucrative market, since as we all know - people as commodity was becoming and still is a scarce resource. Clients are also waking up and asking why 1000 engineers on the floor are better than 100, when engineering design in all aspects of industry, new technology aside, is mature. Why is it that we start with a clean sheet of paper with every project or that neighbours in the same industry segment and location just happen to have completely unique conditions and circumstances that require totally original design (Local conditions aside)? The answers to this question appear when we explore the role of the project team and how it is structured. We will need to investigate team culture and levers for success. Then we will formulate a business case for a team to be able to follow traditional project management practices with EPCM delivery models but yet end up with an alternative look, feel and result. An outcome where more input is not necessarily better and the client and consultant both are aligned with success measured in dollars and a win-win outcome for both parties.

Jan 1, 2009

By T Sua, B Wright

"BHP Billiton West Australian Iron Ore (WAIO) conducts an extensive geometallurgy program for its iron ore deposits in the Pilbara with the focus on determining the lump yield (the mass percentage of >6.3 mm rocks) and the lump and fines grade for iron ore products. The geometallurgy program provides accurate information to design engineers and technical marketing teams on the performance of different iron ore mineralogies for future deposits. Additionally geometallurgy results are being used to guide short-term production planning with their introduction into short-term geology models and grade control models. The data that underpins this knowledge is from dedicated geometallurgical programs, drilled using PQ (~83 mm) holes. These holes are crushed by intervals that are based on geological definition which provides an indicative lump yield and lump and fines grade. The lump is then subjected to standard dropping and tumbling test stages to produce a simulated lump and fines product. In the past, quality assurance, quality control holes were drilled using HQ (~64 mm) holes for geochemistry purposes. These holes were crushed to provide an indicative lump yield and lump and fines grade and then 100 per cent is sent for assay (with no dropping and tumbling). Utilising data from HQ holes can significantly increase the indicative geometallurgical data available. This paper compares the geometallurgical results from both PQ and HQ holes from a range of bedded iron deposits (Brockman and Marra Mamba). The PQ and HQ data are compared by orebody, stratigraphy and depth to exclude factors that are expected to influence geometallurgical results.CITATION:Wright, B, Sua, T, Robertson, B and Van Dijken, B, 2016. Comparison of Diamond Drill Size on Iron Ore Geometallurgical Results, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 161–166 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S C. Dominy

Grade control programs aim to deliver economic tonnes to the mill via accurate definition of ore and waste. The foundation of a successful program is high quality sampling supported by geology and a suitable data management and modelling system. Underground sampling methods include chip, channel and panel samples; grab/muck pile samples; and drill-based samples. Grade control strategy is related to mining method and orebody type. Sampling protocols must be designed to suit the style of mineralisation in question. Holistic studies focussing on ore mineralogy and gold particle deportment, size and distribution are required for sample collection and preparation protocol optimisation through ‘Theory of Sampling’ application. Where possible, such programs should be undertaken early in the life of a project. Appropriate assaying procedures are also required. Program implementation will require suitably skilled individuals to train and mentor staff, with ongoing Quality Assurance/Quality Control (QA/QC) monitoring and review will allow protocols and staff to be updated as required.

Aug 22, 2011

With the iron ore industry in Australia producing hundreds of millions of tonnes of ore per annum, the associated costs of these operations extend into the billions. It is no surprise in the current economic climate that more and more companies are looking into different ways of optimizing their costs to keep their sites operational. One way of improving operations is the use of electronic initiating systems like i-kon and Uni tronic detonators. These systems have been used around the world to improve current practices and optimize drill and blast costs. However, these systems have yet to make an impact upon the iron ore sector in Australia. Some of the potential improvements include:pattern expansion and a subsequent reduction in drilling and explosive costs;improved fragmentation and hence increased dig rates, thereby driving $/tonne down;embracing the 'mine-to-mill' concept by reducing the downstream costs of crushing and milling;improving the overall condition of pit walls and floors, leading to a safer working environment in which optimal haulage performance can be achieved; and improvements in vibration management around heritage sites and critical infrastructure, thereby saving the cost of relocation works. This paper introduces some of these concepts and the process of making the changes leading to potential savings from the improvements, using various examples as proof of the concepts.

Jan 1, 2009

By W J. Rankin

A study was carried out to compare the environmental impacts of a number of process routes for lead and zinc metal production from sulphide ores using Life Cycle Assessment methodology and based on average industry data derived from the literature. The processes investigated were:blast furnace production of lead; Imperial Smelting Process for lead and zinc production; and electrowinning of zinc with the mining and mineral processing stages common to all three routes. The effect of a number of process variables, namely ore grade, fuel source for electricity generation and efficiency of generation, on the environmental impacts was also examined. The environmental impact categories considered in the study were:total (or full cycle) energy consumption; Global Warming Potential (GWP); and Acidification Potential (AP). The results of the study show that when produced separately, zinc production is more than twice as energy intensive as lead production (viz 48 and 20 MJ/kg respectively), however when produced jointly by the Imperial Smelting process, the energy intensity of the two metals is not all that dissimilar (viz 36 and 32 MJ/kg respectively). The metal production and refining stage was found to make the greatest contribution to the overall environmental impacts for all three processes. The study also highlighted the importance of taking a life cycle approach when comparing the environmental impacts of different processes.

Jan 1, 2002

By Segnit E. R

Results are reported of a study of the reactions occurringin the combustion of chaIcopyrite particles underconditions simulating those in the shaft of a flashsmelter.The reactions were studied using kinetic and mineralogicaltechniques. Reactions. rates above 500°C wererapid, most of the reaction taking place in less than 50ms. Final products were copper-iron ferrites with spineltype structures. Probable reaction mechanisms are discussed.

Jan 1, 1977