Search Documents

Small scale' table concentration tests have many critics. Many metallurgists consider that such tests are of problematical value because of the difficulties involved in conducting and interpreting them.Many kinds of small-scale ore dressing tests are difficult to conduct, and there is, perhaps, good reason for thinking that table concentration tests are amongst the most difficuIt.Interpretation of results from small-scale tests is the responsibility of the metallurgists and engineers in charge, and it is often held that small-scale table concentration tests are particularly difficmlt to interpret.TESTING FOR TABLE CONCENTRATIONOn analysis it appears that the difficulties encountered in conducting small-scale table concentration tests are of three fairly distinct kinds. Firstly, there are difficulties due inherently to the smallscale nature of the operations; for example the smaller width of all mineral bands on the table and the less complete separation due to the shorter length of travel between the feed and discharge points.Secondly, there are the effects of batch operation owing to the fact that the mineral particles behave differently during the initial period when the sample is just beginning to spread over the table, the middle period when feed and discharge are even and continuous, and the final stage, when the last of the sample has been added and the table is beginning to empty itself.

Jan 1, 1954

By K W. Mills, N R. P Baczynski, J Mylvaganam, D A. Prado, M F. Lee, I A. de Bruyn

"This paper presents the second part of a study of the assessment of rock stress inputs on the performance of various new mining designs at the Ok Tedi large open pit mine in Papua New Guinea. Over the years, four programs of rock stress measurement have been completed at Ok Tedi, each providing different interpretations of the in situ field stresses. Details of three of these programs and interpretations are provided in the precursor to this paper, entitled ‘Rock Stresses at Ok Tedi, Papua New Guinea’ (Lee et al, 2014).This paper explains how the various stress interpretations were utilised in the modelling of the proposed new open pit and underground mining excavations, comparing where possible their expected effects on stability. The modelled performance of three specific mine components have been discussed here as case studies, including: the below-pit drainage tunnel, as the floor of the open pit workings is mined down from 350?m above, to within just 75?m above the crown of the tunnel the stability of the 1000?m high slope of the proposed West Wall cutback the proposed sublevel open stoping extraction sequence in the Gold Coast orebody beneath the East Wall, for which only the likely ‘worst-case’ stress regime was used to assess sequencing and stability issues.The benefits of scheduling the collection of detailed rock stress measurements and other input data from a range of different sources at various stages of the projects are discussed.Alternative in situ stress models have less stability impact on open pit slopes than on underground mine excavations.CITATION:de Bruyn, I A, Baczynski, N R P, Lee, M F, Mills, K W, Mylvaganam, J, and Prado, D A, 2014. The application of rock stress inputs to stability assessments at Ok Tedi Mine, Papua New Guinea, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 43–54 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

Despite the recovery of approximately six million ounces of alluvial gold from the West Coast of the South Island, New Zealand during the last 140 years, a great deal of this having been obtained via sluice boxes and riffle tables, there has been little advance in riffle table technology during this period. In this paper contemporary riffle table design and current operational practices are examined. Studies of gold loss to undersize tailings are described. In addition recommendations derived from recent research carried out in North America are contrasted with gold saving strategies adopted by West Coast miners.

Jan 1, 1992

Triboelectric Separation - Beneficiation of Coal The performance of triboelectric separators is highly sensitive to the selectivity of the particle charging process. This paper presents a quantitative study on triboelectric coal beneficiation. The performance of different charging media was studied. Stainless steel was identified as having a work function between that of coal and silicate gangue and found to be the optimum charging medium for coal beneficiation. Recent results from separation tests were performed where silicate gangue was separated from crude coal using a parallel plate free-fall separator are illustrated.

Sep 13, 2010

The Physiographical Features of the Region The Middleback; Range proper, from the Iron Duke in the south to the Iron Prince in the north, extends in a meridional direction for 21 miles, but may well be taken to embrace also the Iron Knob and Iron Monarch prominences so that the total length of the Range is 37 miles.Although no great altitudes are reached, the slopes of the high country are steep and the Range stands out prominently above the peneplaned surface of upper Eyre Peninsula. The Range is built up of sub-parallel ridges at some places, and its continuity is interrupted by transverse breaks or gaps resulting from normal stream erosion and corrosion during earlier periods when precipitation was heavier and streams were more active. Traces of high-level gravels remain on the flanks of Kimba Gap. A former mature stream on the western side of the Range has had its lower reaches blocked by sand and the old stream channel has been converted into an eiongated basin of internal drainage. The sand dunes in this area appear to be practically stationary at present, being fixed by mallee vegetation. Their trend is west-northwest.The relief of the Range is regarded as having been determined primarily by meridional strike faulting and selective silification of some of the beds. Dip faulting on the Iron Duchess leases has produced subsidiary features only.The Rocks of the Region: In order that some of the points made in the discussion of the genesis of the ore bodies may be appreciated it is necessary to consider the stratigraphical succession and the igneous types represented. This classification may be...

Jan 1, 1949

BHP Billiton Olympic Dam produces copper cathode, uranium oxide concentrate and refined gold and silver. The operation is comprised of an underground Mine and Processing Plant and is located 560 km north of Adelaide. Water for the operation is sourced from two wellfields located 120 and 200 km from the operation in the Great Artesian Basin (GAB) at a rate of approximately 36 ML/d. Regulatory drawdown limits were established to protect regional GAB springs and are monitored at compliance bores. Drawdown was predicted in the æOlympic Dam Environmental Impact StudyÆ (Kinhill, 1997); however, pumping at higher volumes may have the potential for increased drawdown resulting in a trend towards the compliance limits. In recent years increased usage of water in the Concentrator and Hydromet sections of the Processing Plant has caused excess process water reporting to the Tailings Retention System (TRS). This has resulted in excessive amounts of liquor ponding on the tailings cells with a potential impact being contamination due to seepage of liquor to groundwater. Effective management of water by the operation is necessary to both reduce GAB drawdown and reduce the amount of liquor on the tailings cells. A site working-group has been established to investigate and pursue opportunities to improve the water use efficiency of the operation. This paper will highlight the issue of water management at Olympic Dam and discuss the various options currently being investigated to improve management of this important resource.

Jan 1, 2006

By P Clark

This paper discusses the challenges, solutions and lessons learnt as tunnelling work continues on the Melbourne Main Sewer Replacement (MMSR) project.The MMSR project is a $220 million dollar project for the Melbourne Water Corporation. It involves the construction of approximately 4.2 km of new sewer from the southern fringe of the CBD through the inner metropolitan suburbs of Port Melbourne and South Melbourne.Of the 4.2 km of sewer currently in construction approximately 2.2 km will be constructed using a 2.95 m diameter Lovat EPB tunnel boring machine (TBM) with approximately 1.9 km of small diameter (300 to 600 mm) reticulation sewers constructed using trenchless techniques.These sewers are being constructed in a dense urban environment, which means that the tunnels and shafts are often in close proximity to buildings and structures. The underground constructionof the sewer is further complicated by the variable geology of the ancient Yarra River delta which includes weathered basalts, the infamous Coode island silt formation and fine loose sands.Some of the key challenges and lessons learnt so far during construction include:· steering and alignment control of the TBM through very soft silt with little residual strength,· development and refinement of a monitoring and alarm system for leaving the machine dormant on a day works only project,· control and measurement of tunnel lining defl ection during ring build and grouting,· prediction and monitoring of surface settlements during tunnel excavation,· improved understanding of the geology and hydrogeology at this previously unchartered area of Melbourne,· consolidation settlement due to dewatering at shafts required careful construction controls, and· ground support and excavation in close proximity to the existing 110 year old sewer which requiredvery detailed risk control measures.

Mar 8, 2011

By E Niva

The IsaMillÖ is challenging the way that plants are designed and operated. This paper challenges existing designs of concentrator flow sheets, particularly focusing on magnetite circuits.   From what has started out as a small scale ultra fine grinding mill in the pharmaceutical and pigment industries, it has been redesigned and improved upon for mineral processing, and has been the mainstay of fine grinding applications for over ten years. These applications have required energy efficient grinding to succeed, and have been predominately in the base metals industry.   Further development of the IsaMillÖ has now resulted in the machines being able to treat larger tonnages, with higher capacity motors. This development, along with the introduction of purpose designed ceramic media, has allowed the mill to treat courser feed sizes. At the same time, the mill still offers highly efficient grinding, and has enabled it to be operated in coarser tertiary and secondary grinding applications.   The acceptance of the mill in coarser applications, predominately in base metals and PGM applications, has enabled the IsaMillÖ to be a serious contender for beneficiation in other minerals. One such application is the potential for IsaMillsÖ to be part of magnetite flow sheets, which are being considered in Australia to meet the growing iron demand of China. The high energy efficiency of the IsaMillÖ compared to conventional technologies, as well as the smaller infrastructure requirements, provides a great opportunity to reduce the power intensity of magnetite circuits.   This paper will examine the use of IsaMillÖ technology in conventional grinding applications, including recent testwork in a primary grinding base metal circuit, as well as testwork on magnetite ore comparing a lab scale IsaMillÖ with a lab scale Tower Mill.   The growing demand for minerals over the next decade, coupled with higher energy cost, will result in energy efficient technology, such as the IsaMillÖ, being included in standard circuit design.

Jan 1, 2008

By D P. Blair

Rio Tinto’s Hope Downs Operations are currently mining iron ore in their South Central Pit. Prior to the commencement of mine operations, Hope Downs carried out an extensive archaeological investigation and identified an ancient rock shelter lying within the proposed mine boundaries. The site is significant to the traditional owners/custodians of the land in this part of the Pilbara, and thus the final pit design was changed to preserve the rock shelter, which now lies 30 m outside the mine boundary. In order to further preserve this ancient dwelling from blast-induced damage, blast design procedures were improved over time to minimise the vibration impact when blasting close to the shelter. Blasting and vibration monitoring commenced in May 2008 using pyrotechnic delay sequences and normal-direction firing. In October 2009 electronic delays were used to reverse-fire blasts close to the shelter in order to create a damage zone between the initiating holes and the rock shelter. A detailed statistical analysis of the vibration data shows a reduction in the higher levels of vibration for blasts fired after October 2009, which is most likely caused by the created damage zone. In May 2010, a site-specific vibration model was developed and implemented, and based on Monte Carlo waveform superposition. This model was used to give a further insight and improvement to the blast delay sequences when blasting close to the shelter. However, such models are expensive to implement and have limitations, which reduces their potential for estimating the probability of getting an excessive vibration due to a given blast design. In this regard, it is more realistic and significantly less expensive to use a recently developed probabilistic analysis based on simple charge weight scaling. This analysis shows that there was a higher probability of exceeding prescribed vibration limits at the rock shelter for blasts fired before October 2009 than there was for blasts fired after October 2009.

Nov 8, 2011

By C Vejrazka

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant that produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment the ore.The occurrence of air blasts is one of the principal mining hazards in block caving operations between the time of first undercutting and breakthrough of the cave to surface. As such, it needs to be managed continuously, and risk assessments need to be reviewed on a regular basis for applicability to changing conditions. Unfortunately, there is little literature on how to practically approach air blast risk assessments in a way that can be incorporated in the day-to-day operation of a mine. Previous methods of assessing air blast risk were tedious and results were often unrepeatable.With the extension of the E48 Lift 1 extraction level, it was necessary to assess the air blast risk for the extension drives and develop operational guidelines for production from the extension. A review of the methodology for assessing air blast risks revealed substantial improvement opportunities.This paper outlines the principles used for air blast risk assessments at Northparkes Mines and the methodology employed to achieve efficient, repeatable and auditable results.CITATION:Vejrazka, C, 2016. Northparkes Mines’ current air blast risk assessment practices for block caving operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 257–264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

A new test coke oven of 7 cu. ft. capacity is described. The oven was designed to simulate conditions in a central section of a battery oven and a special feature is the achievement of unidirectional heating from theflues on either side of the charge.The method of charging permits close control of charge conditions such as bulk density and moisture content.These conditions, as well as coking conditions (e.g. flue temperatures and coking time) must be varied to simulate conditions in different batteries. The effects of several variables on coke quality are discussed.Using test oven conditions corresponding to those of Newcastle steelworks batteries, good agreement was obtained between strength indices of test oven and battery cokes. For 17 tests, the average ASTM stability and hardness indices for the test oven coke were 38· 5 per cent and 69·7 per cent, while those for the battery coke were 37· 4 per cent and 67·6 per cent.Observed relationships between coke yield and productivity, and volatile matter and charge moisture are given.The use of a test oven to classify test coals into prime-, medium-, poor-, and non-coking coals is discussed.This may be achieved by observing the effects of the test coal in blends with other coals. The results of a series of blending tests are presented.The dangers of attempting to predict coke quality from a single coal property are pointed out, since this can be done only for very restricted ranges of coals.A diagram is given showing the established trends in the effects of blending various types of Australian coals on coke strength.

Jan 1, 1970

Modelling and simulation are important aspects of flotation research, which may assist in the design of new circuits and the optimisation of existing ones. Flotation research in the AMIRA P9 project has developed a methodology for flotation plant modelling based on determination of cell (pulp) characteristics. froth characteristics, and ore floatability (using floatability components). The implementation of this methodology requires the determination of ore floatability, to which end a small flotation pilot plant known as the Floatability Characterisation Test Rig (FCTR) has been designed and then built and kindly made available to the AMIRA P9 project by Baker Process. The FCTR has a 2 tph capacity and consists of six 130 litre rougher/scavenger cells and six 50 litre cleaner/recleaner cells. The Mintek FloatStar pulp level control system is used to control the pulp level in all cells. A number of experimental procedures have been developed for using the FCTR to obtain the data required for the P9 flotation models. These procedures include how to determine the floatability parameters, Pi and mi, the bubble surface area flux, Sb, the mean residence of the pulp in the cell, t, water recovery. Rw, froth zone recovery, Rf, and the degree of entrainment, ENT. The flexibility of the FCTR allows it to be used in numerous flotation studies such as stream characterisation, reagent testing, grinding experiments, power studies, oxidation studies, and scale-up and simulation studies. This paper will describe the design and operation of the FCTR and the procedures that will be used to obtain data from the rig for modelling purposes.

Jan 1, 2000

Retreating Cu-Mo Rougher Tailing by Flotation for Concentration of Copper and Molybdenum

Sep 13, 2010

A recoverable uranium resource, shown to be suitable for in situ leaching, was discovered at Honeymoon in South Australia in 1971. Exploration of the deposit was carried out during the period from 1973 to 1979. Uranium mineralisation occurs in a coarse-grained unconsolidated sand aquifer located in the Yarramba Palaeochannel at a depth of approximately 110 m. Following initial development during 1979 to 1983 and the construction of demonstration leach facilities, the Project was put on hold. Southern Cross Resources purchased the Project in 1997. Government approval was received in March 1998 for the operation of on-site demonstration leach and recovery facilities while an Environmental Impact Statement was prepared and a 1000 tpa commercial production plant was designed. The Environmental Impact Statement (EIS) was released in June 2000 and operation of the test facility was completed in August 2000. Acceptance of the EIS by Commonwealth and South Australian state governments was announced on 20 November 2001. A Mining Lease was granted over the area of the proposed ISL operation on 8 February 2002. Operation of the Project is entirely dependent on using highly saline underground water resources to supply process and human needs. The management of discharge streams from the plant by re-injection was approved. The Honeymoon demonstration plant was the first adaptation of the solvent extraction process to highly saline in situ leach solutions. As such, it incorporated a number of unique operating and installation features. The trial period enabled optimisation of the process chemistry, additives and management and serves as an invaluable base for the proposed plant design and future operation. This paper discusses the nature of the uranium occurrence, the effect of saline water on the leach process and equipment, project design and environmental considerations, the requirements for disposal of discharge streams to minimise the impact on the arid environment and the requirements for rehabilitation following project completion.

Jan 1, 2002

By S Morgan, L C Pagdalian, S Serdzeff, C Malaloy-on

It is widely accepted that mineral deposits are decreasing in metal grades. To remain profitable and meet market demand, mining companies are expanding their operations by increasing the tonnage treated. These expansions may include new concentrators with higher nameplate tonnages or upgrading the capacity of existing ‘brownfield’ operations. In many cases, the brownfield upgrade route is preferred as it is less capital intensive; however, brownfield upgrades are never straightforward and present many metallurgical and engineering challenges.For example, to increase feed throughput at a brownfield site, there will be a requirement to modify the mine development plan. This may result in the ore mineralogy varying beyond the current feed fluctuation range. To accommodate these ore variations, a combination of mineralogical analysis and small scale testwork can be used to develop a new process flow sheet to achieve the product recovery/concentrate grade requirements. In general, however, flow sheet development does not usually consider site specific layout constraints and equipment requirements. At sites where future expansions were never considered, taking this silo approach could lead to project delays and compromise the circuit design.Engaging an experienced technology partner ensures the nominated project team is involved throughout all stages and aspects of a given brownfield upgrade – from conceptual flow sheet development, through to detailed engineering, construction and commissioning. The recent Carmen Copper Corporation (Carmen Copper) circuit upgrade has been completed in technology partnership with Outotec. The circuit upgrade was extensive and included new equipment additions to the comminution, flotation and dewatering circuits. Carmen Copper’s intimate knowledge of the ore characteristics, in conjunction with a trusted, knowledgeable technology partner, facilitated a robust circuit design, and fast-tracked the project execution. This paper deals specifically with the flotation circuit upgrade and highlights the benefits to Carmen Copper of this holistic approach.CITATION:Morgan, S, Serdzeff, S, Malaloy-on, C and Pagdalian, L C, 2014. The benefits of technology partnerships during brownfield upgrades, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

The granulites and related "dry" igneous rocks tend to be passed over during exploration for metals. Preliminary data show that high trace concentrations of eu, Ni, and other metals of economic interest are commonin orthopyroxene and some of the other granulite minerals. During retrograde metamorphism of granulites, pyroxenes are converted to amphiboles or phyllosilicates, and significant quantities of metals are released andbecome available for incorporation into new mineral phases, or may be transported elsewhere. S-rich scapolite is the normal scapolite of granulites. Its retrogression to secondary plagioclase provides much S which scavengesCu and Ni, from pyroxenes undergoing retrogression, thus producing ore-fluids. A full analysis of a scapolite with 5·10 per cent SOg is given.Beryl is unstable in granulites but the rare Be mineral taaffeite (Al4Mg(Be, FeII)Os) with 5·50 per cent BeO occurs in central Australia as a pale green tabular mineral easily confused for chloritoid in hand-specimen.Metamorphic differentiation and mobilization of primary ore concentrations are major factors controlling their post-granulite attitude and grade.Zones of retrograde metamorphism are commonly found cutting or engirdling granulite terranes. As the "volatiles" for the new hydrous minerals of many of these zones are of deep-seated origin and may be juvenile, sulphide mineralization in them may also be of mantle origin. However, it is likely that much of the metal content could be scavenged from the granulites as they are down-graded by juvenile volatiles. Major Bouguer gravity anomalies delineate some granulite terranes (e.g. Fraser Block, Western Australia), and are related to deep-seated geosutures and mantle disturbances.Many granulite terranes are linear belts and appear to be welded to older cratonic blocks.

Jan 1, 1969

Fragmentation Characteristics of Iron Ores from Anshan, China

Sep 13, 2010

By D Giddings, S A. Silvester, S Pickerin

Underground fires represent a constant threat to the safety of underground personnel. Miners in the immediate vicinity may face intense heat, blinding smoke, toxic fumes, fall of ground and other direct effects of a fire. However, the vast majority of victims never actually see the fire, and are overcome either by deadly fumes in the ventilating current or by asphyxiation. The mine ventilation system, which maintains a sustainable atmosphere to the working places, can transport products of combustion with equal efficiency. Miners who are remotely situated from a fire may be forced to evacuate considerable distances, through dense smoke and fumes, or even become cut-off from escape. Additionally, miners may become confused by unfamiliar ventilation characteristics caused by fires. Conveyor belts are widely used for transporting minerals in mines as well as in many other industrial situations. Because they contain large amounts of polymeric materials their use in certain environments, especially coal mines, but also in steel works, power stations and other enclosed areas must be controlled to minimise the fire risk. Over last nine years there have been 60 fires in underground mines in the UK alone and that of these, half have been associated with conveyors. This paper summarises the results obtained from a recent research project that has developed a preliminary computational thermal and fluid dynamic model to represent the spread of flame along a typical conveyor belt used in UK deep coal mines. The results of these models have been calibrated against a series of experimental tests performed within a surface fire test gallery. An improved knowledge of the burn characteristics and rate of release of the products of combustion from conveyor belt fires will assist in the development of better fire detection and fire fighting techniques.

Jan 1, 2005

Agglomeration for Copper Heap Leaching Agglomeration of ore is a method which can be used to eliminate the migration of fine grained particles throughout a leach heap. Without agglomeration, fine ore particles are able to migration within the heap, clogging flow channels and producing large areas where access of the solution is poor. In order to gain the benefits of agglomeration and improve agglomerate strength even further in copper heap leaching, an economical, acid-resistant binder is needed. However, most binders have been used without any systematic reasoning. A set of novel testing methods were developed, including a soak test, percolation flooded columns, and larger long-term leach columns. The soak test compares the degree of breakdown when agglomerates are subjected to an acidic environment. While the percolation flooded columns and larger long-term leach columns evaluate the flow of leach solution throughout the ore bed. Systematic studies have been completed on a wide range of binders using these novel testing procedures. It was found that for a low grade chalcocite ore, which was rich in silica, from a southwest US mine, polyacrylamides reduced the fines migration the best in the novel soak test. The non-ionic binder, in particular, was found to reduce fines migration as much as 93 per cent. Several of the binders tested were shown to increase the hydraulic conductivities of the agglomerated ore up to 2.5 mm/sec, compared to a hydraulic conductivity of only 0.25 mm/sec when no binder was used. These binders also prevented 'slumping' of the ore, which indicates a decrease in breakdown of the agglomerates. The use of a binder also showed no interference with leaching reactions in long-term leaching experiments.

Sep 13, 2010

The West Coast region of the South Island is situated astride the Pacific û Australian plate boundary zone. The most significant component of this zone is the Alpine Fault. A variety of reconstructions of the pre-Alpine Fault plate tectonic configuration of the New Zealand continental area have been attempted over the past 25 years or so. Most of these have not been closely constrained by a regional compilation of field data related to the age and horizontal displacement history of the Alpine Fault. A model in which the Alpine Fault was initiated no earlier than the interval 18 - 16.5 Ma (B.P.) is proposed, a significantly younger age of inception than has been widely accepted as the onset of dextral displacement along the plate boundary through the South Island. A subsequent history of displacement is presented consistent with the West Coast basin stratigraphy. The alluvial gold content of some parts of the Miocene to Pleistocene conglomerate sequences is also discussed.

Jan 1, 1996