Search Documents

By B Mobilio, G B. Sharrock, J L. Lett, I Brunton, T Thornhill

Full-scale marker experiments at Cadia Valley underground operations have been ongoing for over 14 years. Initial marker experiments were undertaken in the Ridgeway sublevel cave (RW) (2002), and subsequently at Ridgeway Deeps (RWD) (2008) and Cadia East PC1 (CEPC1) (2012) block caves. Over 25 000 markers have been installed at the three caving operations to date (approximately 20 000, 3000 and 2500 for RW, RWD and CEPC1 respectively). These experiments aimed to quantify and assess the geometry of the extraction zone, development of the extraction zone over time, variability of flow behaviour and factors affecting flow behaviour in both the near and far field cave column. This paper discusses marker recovery results from the RWD and CEPC1 caves.With respect to the two cave operations, marker recovery in both the near field (markers recovered vertically within 70 m of the extraction level) and far field (markers recovered vertically above 70 m of the extraction level) indicates disturbed flow behaviour where marker recovery is not spatially uniform during material extraction. Two distinct patterns or transient behaviours in the extraction zone are indicated. For RWD (advanced undercut), early material recovery was close to the major apex, and expanded towards the centre of the drawbell as more material was extracted. The inverse was observed for CEPC1 (post undercut), where recovery occurred in the centre of the drawbell initially, and expanded outwards towards the major apex. This trend of recovery for the two operations continued in the far field. In the region above the major apex, recovery was observed for all heights, with no clear height of interaction zone (HIZ) indicated. All of these behaviours significantly deviate from both conventional ellipsoidal flow theory and Laubscher’s (2000) design guidelines. For this reason these new mechanisms are termed the Disturbed Extraction Zone (DEZ).For the CEPC1 marker experiment, electronic markers were utilised to investigate the vector movement of material in the near field. Marker recovery movement vectors in the near field indicate extraction zone widths in the order 30 m, with localised marker recovery outside this region (significant horizontal movement of material potentially due to cave muck pile rilling and blast burden movement). Analysis is ongoing for far field marker vector movement, and will be reported once additional marker recovery has been obtained.CITATION:Brunton, I, Lett, J L, Sharrock, G B, Thornhill, T and Mobilio, B, 2016. Full-scale flow marker experiments at the Ridgeway Deeps and Cadia East cave operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 141–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D Fukuda, K Kaneko, R Kudo, J Kodama, Y Fujii, T Sasaki

"Estimation of stress state as well as elastic modulus is important for the prediction of a rock slope deformation in an open pit mine since it can strongly influence the mining-induced deformation of the rock slope. This study applies a method to evaluate regional stress state and Young’s modulus by analysing the mining-induced deformation of ground. The effect of changes in regional strain state due to tectonic plate motion can be accounted for using the proposed method. Mining-induced deformation can manifest itself as changes in ground surface geometry resulting from mining activity. There are three underlying factors that can contribute to the deformation: displacement induced by the effect of gravity displacement induced by the effect of horizontal regional strain incremental change in the horizontal regional strain. The relative displacement arising from the mining excavation at the Torigatayama limestone mine in Japan has been measured by Global Positioning System (GPS). Both the regional stress state and Young’s modulus were estimated by back analysis of the change in distance between GPS stations using a 3D finite element method. It was shown that the reliability of the estimation improved with an increase in displacement due to mining progression. It was also shown that values for Poisson’s ratios of less than 0.10 are reasonable estimates with values for Young’s modulus between about 5?GPa and 10 GPa. The magnitude and direction of the maximum compressive stress in the district surrounding the Torigatayama mine were estimated to be between -6.4 MPa and -4.4 MPa and around N25E respectively.CITATION:Kodama, J, Sasaki, T, Fukuda, D, Kaneko, K, Fujii, Y and Kudo, R, 2014. Estimation of regional stress state and Young’s Modulus of ground at Torigatayama Limestone Mine in Japan, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 135–142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By S M. Jowitt, G M. Mudd

"The mining industry is the source for the vast majority of the metal, mineral and energy resources we use on a daily basis. New deposits are discovered over time and are developed into mines before being rehabilitated – a sequence that when repeated can help contribute to the noble notion of ‘sustainable development’, despite the generic concept of mining being the unsustainable consumption of non-renewable resources. The scale of the modern mining industry is immense – from iron ore and coal to base and precious metals, modern mines are sometimes hundreds or thousands of times bigger than their long lost historic ancestors. We also live in a world with emerging and increasing demands for so-called technology metals (aka ‘critical’, ‘e-tech’ or ‘specialty’ metals) that are needed to feed the rapid growth in renewable energy (especially solar photovoltaic panels and wind turbines), consumer electronics, sophisticated military technologies and super alloys, amongst other uses. These elements include the rare earth elements, indium, germanium, tellurium, rhenium, selenium, gallium and many others, most of which had few or no known uses in the recent past. Although the mining industry has been successful in developing ever larger mines and increasing the scale of production, the key issues underlying the future of the industry are declining ore grades, increased tailings and waste rock generation, the presence of toxic or other impurities, balancing the economics of primary and secondary products, stricter environmental conditions, more difficult exploration, increasing community expectations, as well as the processing of more complex or refractory ores, let alone the recent volatility in world commodity markets. Here, we synthesise our recent research on many of these various issues, focusing on the need to link all areas within the mining chain from mineral resources through mining to environmental performance in order to ensure we obtain the most out of our modern mining effort. The paper presents a unique and detailed assessment of the sustainability challenges and opportunities facing modern mining – and geometallurgical thinking is at the heart of this conundrum.CITATION:Mudd, G M, Jowitt, S M, 2016. From Mineral Resources to Sustainable Mining – the Key Trends to Unlock the Holy Grail?, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 37–54 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By A Wanninayake, E Novello, I Gillani

A residue storage facility (RSF) was designed to cater for Davidson Creek Area and Robertson Range Area operations under the FerrAus Pilbara iron ore development project in the Pilbara Region, Western Australia. Annual ore production was about 15 million tonnes over a period of up to 15 years. The RSF was designed to handle a tailings production rate of 2.2 Mt/a over the project life with ability to be expanded at a later date. The composition of tailings was predominantly -45 ¦ material with some spiral reject material. The fraction of solids was expected to be between 40 per cent and 50 per cent solids by weight.The RSF was designed as an above ground storage facility, integrating with a mine waste dump planned close to the selected RSF site. This integration helped to increase the stability of the RSF embankment and to reduce the construction cost. The main source of construction material for the remaining part of the RSF embankment was selected to be mine waste. The RSF was designed to be constructed in stages by considering the availability of mine waste according to the mining schedule. The use of mine waste for construction of RSF embankments has several benefits over use of borrowed material. These include less construction costs and less disturbances to the environment, by minimising borrowed areas and waste dump footprints.CITATION:Wanninayake, A, Novello, E and Gillani, I, 2013. Effective use of mine waste in the design of a residue storage facility, Pilbara region, Western Australia, in Proceedings Iron Ore 2013 , pp 39-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M McGrory, A Rodolfo, J Paredes, L E. Manguba, K A Villaspir, G Webb, R Setiagani, H Cardenas

"OceanaGold’s Didipio operation has been in operation for three years. Integral to the flow sheet design is a flash flotation circuit treating a portion of cyclone underflow, consisting of an Outotec SK-500 flash rougher and an Outotec TC10 flash cleaner and a SB-2500 falcon treating flash rougher concentrate to recover fine free gold.Flash copper recovery has been holding steady at 60 per cent, while flash gold recovery at 50 per cent. Gold recovery from the gravity circuit is 22 per cent, bringing the overall flash plus gravity gold recovery to 72 per cent.Operation of the flash rougher is mainly by pulp level control. Control of copper grade in the flash cleaner is mainly controlled by air inflow and flash cleaner pulp level control drives copper recovery. Gold recovery around the circuit is mainly driven by gold head grade.SB-2500 concentrate is scalped with a 250 micron screen with the coarse fraction reporting to a SB-250 falcon, concentrate of which combines with the screen fine fraction to a Gemini table.Citation:Cardenas, H, McGrory, M, Webb, G, Paredes, J, Setiagani, R, Villaspir, K A, Manguba, L E and Rodolfo, A, 2016. Didipio Flash Flotation and Gravity Recovery Circuit, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 123–126 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By P Wahyono, H Vega, S Riza, P Vergara, P Gonzalez-Carbonell

PT Freeport Indonesia (PTFI), operating in the Ertsberg Mining District in the Province of Papua, is developing the Grasberg Block Cave copper-gold mine. The site aims to output 160 000 t/d and will be located underneath the current Grasberg Open Pit. Initial studies of the potential to develop a block cave mine in the Grasberg orebody have revealed that the mine will require significant volumes of air. The Grasberg Block Cave (GBC) project requires four primary fans (3750 kW each) to support production at full capacity.Fan #1 commissioning was accomplished successfully on 9 February 2012. However, Fan #2 chamber, which is separated by a 20 m pillar, had not been completed. The main challenge was Fan #2 chamber still needed to be benched. The risk of damage to the critical infrastructure in Fan #1 chamber, including ground support, cracks in pedestals, and misalignment in the impeller shaft were considered. The challenges were blasting the bench without damaging the surrounding infrastructure, completing the work safely and meeting the schedule. This was achieved with the engineering control methodology. This paper summarises the benching process of Fan #2 chamber and its impact upon Fan #1.CITATION:Vega, H, Riza, S, Gonzalez-Carbonell, P, Wahyono, P and Vergara, P, 2013. Excavating an underground primary fan chamber that is adjacent to a fully operational primary fan in PT Freeport Indonesia's Grasberg Block Cave Mine, in Proceedings The Australian Mine Ventilation Conference , pp 115-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By the use of flotation tests it was confirmed that there are two functions of oxygen in sulphide mineral flotation. Sized samples of galena and chalcopyrite were sulphidized, washed free of excess sulphide ion, and then contacted with air-saturated water for certain lengths of time. The mineral was then transferred to a sealed laboratory flotation cell containing water with a known concentration of dissolved oxygen. Xanthate and frother were added and flotation continued for 1 min.Both the extent of mineral oxidation and the concentration of dissolved oxygen markedly affected the flotation of galena and chalcopyrite. The response to a change in either variable is dependent on the level of the other, but generally best flotation occurs with the maximum degree of air saturation of the pulp. Galena flotation is hindered by oxidation of the mineral beyond a small threshold amount but a similar effect for chalcopyrite was not observed...

Jan 1, 1967

By R Van Laeren, G Langerak, S Fityus, K Koosmen

Co-disposal of partly-dewatered mixed-plant rejects (MPR) from coal processing into spoil dumps is gaining favour amongst Australian coalmine operators in preference to conventional tailings disposal methods which require a tailings dam. Owing to their often low permeabilities and high degrees of saturation, MPR materials may be prone to the development of excess pore pressures when covered by spoil during routine dump advancement. The likelihood of dump failure will increase if these pore pressure regimes and the associated delay of shear strength development are not accounted for during waste dump design. To date however, little is known about these pore pressure regimes due to the complexities associated with their in situ measurement.This paper describes the in situ measurement of pore pressures in a cell of MPR placed within a coalmine spoil dump. Four vibrating wire piezometers (VWPs) were placed within a cell that was then filled with MPR and allowed to consolidate under self-weight before advancing an adjacent tiphead across the cell. The VWPs recorded the transient pore pressures during MPR placement and dump construction, and their interpretations are described within the context of laboratory measured parameters. Following analysis of the measured pore pressures, their implications on shear strength and dump design are also discussed.CITATION:Koosmen, K, Langerak, G, Simmons, J, Fityus, S and Van Laeren, R, 2015. Field measurement of transient pore pressures within co-disposed processing rejects placed in a spoil dump, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 63–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By T de Wit, S Meyer

The location of seismic events in mines is traditionally calculated based on the arrival times of P- and S-waves for a given velocity model (homogeneous or heterogeneous). This technique is successful when the sources of seismic events are sudden and localised (eg episodes of fracturing in solid rock or dynamic slip along a plane of weakness) and thus the radiated seismic waves have clear arrivals. In massive mining operations such as block caves, strong seismic signals often originate from the movement of loose rocks on the perimeter of the fracture zone. These signals are easily recordable but do not contain easily identifiable direct P- and S-waves, making the estimation of location through traditional methods more complicated. This problem has been approached by using a ‘brightness’ location method that estimates the origin of seismic waves based on travel times of envelopes of seismic energy. This tool is extended to be applicable in a heterogeneous velocity environment that now accounts for the presence of a cave or other strong velocity perturbations. The suggested method is particularly important when caving occurs in low-stress environments (eg close to the surface).CITATION:Meyer, S and de Wit, T, 2016. Location of seismic events associated with caving using brightness method, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 225–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By E Selvapandian, R Barr

Arrium (previously OneSteel) initiated a desktop study into the performance of its hematite ore beneficiation plant in early 2010. The beneficiation plant utilises jig concentrators and spirals to upgrade low-grade hematite recovered during mining at the Iron Duke (ID) mine site located 60 km south-west of Whyalla. The study, conducted in conjunction with Mineral Technologies, identified a number of opportunities for improvement, which were validated by a series of sampling campaigns and a pilot plant trial. One of the major recommendations was to upgrade the ultra-fines processing circuit from a single-stage spiral circuit to a three-stage circuit. The upgrade of the ultra-fines circuit was estimated to provide a significant increase in fines production and grade.In order to capitalise on the strong iron price at the time of the project, Arrium decided to utilise a fast-tracked approach to design, construct and commission the processing equipment required to achieve the improvements identified. This decision introduced the risk of missing critical steps in the project development process, which could have potentially resulted in major issues in latter stages of the project. In addition to the challenges introduced due to the expedited time line for project completion, this project presented unique challenges due to its brownfield nature. One such challenge faced was the integration of the new equipment and control system software.Furthermore, the importance of the ID ore beneficiation plant (OBP) contribution to the companyÆs export commitments meant the upgrade work had to occur while minimising disruption to normal operation. This decision presented a set of new challenges to an already complex project. One such challenge was the need to build and commission the new spiral circuit in isolation from the operating plant.The aim of this paper will be to highlight some of the challenges faced in a complex brownfield project such as the ID OBP upgrade and discuss how they were managed to enable the successful commissioning of the process in early 2012.CITATION:Selvapandian E and Barr, R, 2013. Managing challenges faced in the brownfield commissioning of an ultra-fine hematite processing circuit at ArriumÆs Iron Duke ore beneficiation plant, in Proceedings Iron Ore 2013 , pp 533-538 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By C Verdel, M Lee, A Oorloff, K Welsh

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Thomson Orogen is a large but poorly understood element of Queensland geology. Extensive cover conceals the Thomson Orogen at depth, thus limiting studies to a small number of surface exposures. Previous studies of the northern Thomson Orogen have been restricted to the largest of these exposures in the Anakie Inlier and Charters Towers Province. Less extensive exposures, including Mt McLaren in east-central Queensland, are largely overlooked and poorly documented. Fieldwork suggests that Mt McLaren is a west-tilted fault block of Thomson Orogen metasediments that are at least 2200 m thick. The substantial thickness of these sediments (which we have named the Mt McLaren Formation) and the consistent shallow marine facies throughout the block suggest deposition in an actively subsiding basin. Initial dating of detrital zircons places deposition of the Mt McLaren Formation in the Late Cambrian to Early Ordovician, allowing correlations with formations of similar composition and age in the nearby Anakie Inlier and Charters Towers Province. Both of these areas have a long history of mining and exploration for gold and base metals, suggesting that correlation of basement sequences across these areas could be beneficial for exploration models of the Thomson Orogen as well as for tectonic models of eastern Australia.CITATION:Lee, M, Verdel, C, Welsh, K and Oorloff, A, 2015. Stratigraphy of the Thomson Orogen – new insights from Mount McLaren, north-east Australia , in Proceedings PACRIM 2015 Congress, pp 551–556 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Experiment of Improving the Quality and Decreasing the Impurity of Titanium Concentrate in Panzhihua Mine in China

Sep 13, 2010

Optimal drill and blast design is a process often neglected by many underground hard rock mines. This is even more important to the new mine where ring designs need to be implemented and refined in a short period of time. In today's environment where more and more mining is being carried out by contract specialists it is the co-operation between a principal and contractor, who are working towards a common goal, that achieves the highest quality end result. The development of drill and blast designs that cause minimal damage to the mine infrastructure is particularly important to Northparke's E26 Block Cave Mine, as it consists of a single extraction level which must survive intact for the life of the mine. The advanced undercut mining method implemented at Northparkes is fired in a sequence which protects the mine development from potentially damaging abutment stress. This paper details how blast designs will be optimised and sequenced to satisfy the conflicting objectives of maximum rock breakage inside the drill pattern and minimum rock damage outside the pattern.

Jan 1, 1995

By N J. Welham

The Intec Copper Process is an environmentally advantageous hydrometallurgical process for the production of high purity copper and associated precious metals from copper sulphide concentrates. The process uses a mixed chloride-bromide lixiviant in an elegant cyclic circuit to leach the copper into solution, rejecting the iron as stable hematite rather than as unstable jarosite. After purification of the pregnant liquor, copper is electrowon at London Metal Exchange Grade A purity, while the anodic energy of the cell is stored as the soluble species, HalexTM, for recycle as the regenerated lixiviant to the leach circuit. Both gold and silver are leached and recovered directly from this cyclic process without resorting to cyanide leaching of the residue. No liquid emissions result from the Intec Copper Process, whilst spent air and water vapour from the leach are released to the atmosphere. The sulphur in the minerals reports to the solids residue in elemental form, without the need for expensive handling of voluminous gaseous sulphur dioxide streams found in smelters. A significant difference to competing smelting and hydrometallurgical processes is that any mercury entering the process from the sulphide concentrate feed is recovered rather than reporting directly to waste or polluting the environment. Outside the process circuit itself, the Intec Copper Process has several notable environmental advantages over competing technologies: Flexibility of scale with low capital and operating costs allow operation directly at the mill head at production rates as low as 15 000 tpa, significantly reducing environmental impacts from concentrates transport. The ability to handle low-grade and dirty concentrates often allows greater recoveries in the mill, improving both the economics and environmental acceptability of a mine by reducing metal losses to tailings. A comparison of the total energy requirements of the Intec Copper Process with those of competing technologies shows that the Intec Copper Process has the lowest energy consumption of any of the known hydrometallurgical processes, as well as improving upon pyrometallurgy under appropriate conditions.

Jan 1, 2002

By N Clarke, J Hunt, A Barros, L Keeney

The Gramalote orebody is a large low-grade gold deposit situated in the San Roque municipality, 124 km north-east of Medellin in Antioquia, Colombia. It is jointly owned by AngloGold Ashanti (AGA) and B2Gold and is currently in Feasibility Study phase. In 2013 AGA requested CRCORE to undertake a preliminary study of the potential application at Gramalote of pre-concentration by screening, part of the Grade Engineering suite. 160 samples of coarse assay rejects (-3 mm) were tested and showed one of the strongest responses seen worldwide to that time, suggesting that about 70% of the gold could be recovered into 40% of the mass. This was seen as potentially markedly improving the Gramalote economics. A large-scale testing program was implemented on site to follow up these results. A total of 18 samples of 17 t each were mined along a pre-existing exploration adit. A complex test flowsheet allowed size fractions to be generated from the as-received material as well as after crushing to 53, 23 and 3 mm, all from the same head sample. The procedures were designed after carrying out a heterogeneity study to measure sampling errors. The coarser size fractions were designed to study the effect of crushing on upgrade response and predict the response on open-pit run-of-mine ore. The finer size fractions were designed to investigate means of predicting the upgrade response across the orebody. The large-scale testing closely confirmed the average upgrade response as predicted from drill core assay rejects but found that only the -53 mm crushed material accurately predicted the upgrade response of individual samples. Ore geochemistry was able to usefully distinguish samples with good and poor response. A small study on drill core suggested that, for Gramalote, fine crushed material distinguishes vein associated and disseminated values but not other factors that control actual outcomes.

Nov 10, 2020

By A Simmons, J Chan, A Li, Q Gu, D M. Brett

The paper presents an example of field density achievements using thin layer deposition and solar drying and compares this with compaction data from laboratory testing and field trials of mechanical densification processes.

Jul 1, 2021

The Black Star lead and zinc ore-bodies, situated in the western zone of mineralisation at Mount Isa occupy an area 2000 ft. long with varying widths from 100 ft. to 300 ft. The strike is N5°W, and the average dip 60° West.To test at depth the potentialities of this area, an extensive diamond drilling campaign was commenced on 16th October 1927. It was continued, with from one to six machines working, until the end of 1931. During this period, 26 inclined holes, with an average depth of 1224 ft, and a total footage of 31,828 ft. were completed. A vertical hole, 2452 ft. deep, for comparative purposes, has been omitted.These drilling operations came directly under the charge of G J Gray, General Superintendent of Mount Isa Mines, and, in the early stages were supervised by E. D. McDermott, of the Mining Trust, London. The foremen, who were in charge of various sections of the drilling operations, were: H Vale, F Bray, J Winston and A A Sanstedt.

Jan 1, 1932

By B J. Hutchison, S Gannon, J Chambers, D Oko-oboh

The Kanmantoo copper mine is located in the Adelaide Hills area of South Australia and is owned and operated by Hillgrove Resources (HGO). The mine is a drill and blast, truck and shovel operation mining sulfide (chalcopyrite) ore located in chloritised andalusite biotite schist. The initial Kanmantoo open pit operation occurred in the 1970s, before falling copper prices closed the mine. In 2010 the mine was reopened by HGO and the Kavanagh cutback of the Kanmantoo pit was undertaken. The Spitfire, Nugent and Emily Star satellite pits were also mined through to 2015 before the latest steep wall Giant pit design was developed to take mining out to 2019.There are no major fault structures and only two significant shear zone structures exposed in the open pit walls. The main Garnet Andalusite Biotite Schist (GABS) unit is quite competent so the pit designs have therefore mainly been controlled by four distinct joint sets. This paper is a case study on the influence of the joint regime on the wall stability of the main GABS unit and how a better understanding of the joint regime and the use of rock reinforcement has allowed the steep wall design to be adopted.The paper also describes the remote geotechnical mapping and slope monitoring techniques used to manage the rockfall risks associated with the steep walled slope design.CITATION:Hutchison, B J, Chambers, J, Gannon, S and Oko-oboh, D, 2017. Case study of joint structure and the design and performance of open pit walls at the Kanmantoo copper mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 355–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By J J. Batchelor, J B. Metson

Titanium (ilmenite) concentrate was extracted from a New Zealandilmeno-magnetite deposit. Tailings from the existing processing line at the Waikato North Head ironsand concentration plant were used as a raw material feed. The titanium bearing mineral extracted was defined as intergrowths of ilmenite and hematite in the size range below 150 um. The Owen-Honda equation was used to determine the conditions forilmenite/hematite magnetic separation. Three distinct regions of magnetic field strength for the mineral separation have been defined. Theoretical estimates from this calculation have been confirmed experimentally. Ilmenite concentrate was obtained using medium field magnetic andelectrostatic separation. The final material contains 40.6 - 42 per cent TiO2 and 39.1 - 39.8 per cent Fe (total). The actual yield from extraction was about seven per cent of the Zircon, leucoxene and monazite were found as byproducts of thetitanium concentration process. Preliminary experiments have shown the viability of industrial zircon benefication.

Jan 1, 2000

By S Robinson, R Perkins, D Barrett, D Kepert, C Fowers

The discovery and delineation of significant mineralisation in the Eliwana region continues Fortescue Metals Group’s strong exploration success. In the decade after the first hole was drilled into Christmas Creek in mid-2004 a total of over 11 Bt of hematite-goethite mineralisation have been delineated supporting the raising of $13 B, construction of five mines, 620 km of rail and a five-berth port. As of June 2014, Fortescue was shipping at the rate of 155 Mt/a. The area including the Eliwana and Flying Fish deposits is one of a number of future growth opportunities that Fortescue is currently evaluating.The Eliwana and Flying Fish deposits occur on the south dipping limb of the Brockman Syncline/Jeerinah Anticline. The Eliwana group of deposits are hosted by the Brockman Iron Formation with the Flying Fish/Broadway group hosted by the Marra Mamba Iron Formation.Structurally the area is dominated by moderate southerly dips of the regional dome and keel style folding. The regional limb is locally cross-cut at a small angle by asymmetric north facing Ophthalmian folds trending 110°. These fold sets, in part, preferentially host subsequent supergene mineralisation. Faulting is only locally apparent.Early phases of exploration commenced in 2006, with mapping of Flying Fish and reconnaissance drilling in 2007. However, due to the concurrent discovery (Clarke et al, 2009) and subsequent fast tracked development of Solomon channel iron deposit and Firetail bedded iron deposit (Simpson et al, 2011) priority was placed on developing Solomon due to its relative proximity to existing Fortescue infrastructure. Staged follow-up drilling of both Marra Mamba and Brockman targets at Eliwana was progressively undertaken from 2008 onward.As of 20 May 2014 a total of 1494 reverse circulation (RC) holes for 54 248 m and 13 diamond holes had been completed, resulting in the delineation of a Mineral Resource of 740 Mt. Exploration via mapping, drilling and metallurgical evaluation of adjacent prospects continues with additional resources expected in the future.CITATION:Barrett, D, Perkins, R, Kepert, D, Robinson, S and Fowers, C, 2015. Geological setting of Eliwana and Flying Fish deposits along the north limb of the Brockman Syncline, Hamersley Province, Western Australia, in Proceedings Iron Ore 2015, pp 219–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015