Search Documents

By Hargraves AJ

Pre-drainage experiments have been conduct- ed at Appin, Cook, John Darling, Leichhardt, Macquarie, Metropolitan and Moura No. 2 Collieries. Appin (550 m deep) experiences particular gas problems in development drivages, and the almost pure CH4 seam gas makes difficult tiro compliance with statutory maxima in intakes and returns. Patterns of 43 mm diameter drain- a,.;e holes drilled ahead and laterally into virgin coal have improved gas conditions in working places and have allowed tolerable advance rates. Cook, Leichhardt, Metropolitan and Moura No,. 2 Collieries have experienced gas and stress phenomena ranging from conical bursts less than one tonne to full scale instantan- -us outbursts of hundreds of tonnes with tens ,f thousands of cubic metres of seam gas. Gas ~Irainage experiments with patterns of holes up a,, 200 mm diameter have been undertaken with ;,;siness monitors on the coal to establish .lative effectiveness. Incremental flows into mg 43 mm diameter boreholes have investigated drainage patterns relative to length, and at comparative incremental flows have nlicated lowered permeability zones at stress ,.,utments. In some CO2 seam gas areas where iammability problems are reduced to perhaps ii, but where outbursts proneness is increased,

Jan 1, 1982

It is hypothesised that increasing the number of loading passes will produce a reduced range of truck payload outcomes compared with four-pass loading. The paper provides analysis to support this hypothesis. It is shown that, hypothetically, loading trucks with five or more passes will result in reduced tendency for overloading and reduced confidence interval for truck payloads that increase the confidence level of containing high end payloads within safe and commercially acceptable limits. Furthermore, increased number of passes provides for more precise bucket load spotting and so improves distribution of payloads within truck bodies. Truck-loading issues examined by the paper include: Improvement in life of driveline components and tyres. Generally tyre costs are relatively moderate; but tyres tend to become an increasingly sensitive performance/cost component as truck scale increases; Reduction of site severity fects flowing on to suspensions, truck frames and structural components generally with potential for reduced long-term repair costs; Less physical body damage due to smaller load increments; Reduced risk of non-compliance with payload limitations for safe braking standards; Increase in loading cycle times tend to increase with scale of loading machinery within the limits of a specific type of equipment (ie rope shovels or hydraulic shovels). Production increase with increased bucket capacity is, to a degree, offset by slower loading cycle times. This is particularly pronounced with front-end loaders but tends to be less noticeable with hydraulic excavators/shovels and electric rope shovels. Decrease in loading time, as a proportion of total truck-cycle time as open pits deepen and dump reaches increase. The production and cost benefits of four-pass loading tend to diminish as truck cycle times increase. The paper also discusses the implications for loading-equipment philosophy to satisfy the future needs of the industry. Cost benefits from upscaling tend to diminish as truck scale increases, so increasing management diligence and close monitoring are required to ensure that expected outcomes are realised. These truck-loading issues have been researched to assess the benefits positive or negative) of four-pass loading in practical scenarios. An attempt is made to determine whether four-pass loading is a æmust-haveÆ or merely a æmythÆ.

Jan 1, 2003

By Sarkar B. C, Sen A. K

India is well endowed with vast reserves of banded hematite ore, about 12 billion tonnes, estimated by some conventional methods. Various authors have assessed this huge reserve using some advanced geostatistical methods. A Banded Iron Formation (BIF) belt named the `Singhbhum-Keonjhar-Bonai' belt in India has been chosen as a case study. In this paper, the experiences of Chiria iron ore, in particular, have been described. This study will finally create a dynamic mineral inventory after standardising the geostatistical parameters which will help to cater for the needs of the stringent quality requirements of the Indian steel industries.

Jan 1, 1995

By G J. Keyter, P J. Terbrugge, Yu Xianb

There has been disappointingly little development in the understanding of the behaviour of rock slopes in open pit mines over the past 30 years. The lack of development in general, and of robust, standardised approaches in particular, are surprising in view of the æultraÆ deep open pit mines that are being developed to depths in excess of 1000 m. Research has recently been carried out into the occurrence of zones of extension strain in open pit slopes. This showed that very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. Results of the research will be presented for different slope heights, slope angles and horizontal to vertical in situ stress ratios. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning, producing easily measurable seismicity. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. Case studies of slope failure in two open pits will be described. In both cases failure occurred æsuddenlyÆ after very limited amounts of deformation. In the first, the slope crest moved suddenly upwards and backwards over a length of more than 200 m, with associated instability. In the second, the horizontal displacement of the slope face was almost an order of magnitude greater than the vertical displacement and occurred æsuddenlyÆ. A recently installed seismic system is detecting events in a significant zone behind the slope face. Both pits were in the 200 m to 300 m depth range at the time of the occurrences.

Jan 1, 2003

By Read T. A

THE Broken Hill South Ltd. is one of ten companies operating on the Broken Hill lode (See Fig. 1). It has two leases-Blocks 7 and 8-of a total length of 2250 ft. on strike of lode.From the surface to 425-ft. level the ore was found principally in the form of carbonates and high-grade friable sulphides. Below the 425-ft. level the ore is found in the form of compact sulphides. The ore-bodies found in the South mine may be broadly divided into two classes...

Jan 1, 1921

By M Kim, J Park, I-K Suh, E Kim, J Lee

One of the key technologies in developing hydrogen-enriched ironmaking operations is the control of the carburisation, melting, and dripping behaviour of the iron ore burden materials. When a hot compacted iron (HCI) is charged in the blast furnace or the FINEX Melter-Gasifier, iron oxide reduction, the reduced iron’s carburisation, and the melting of iron and slag occur successively. This study investigated the reduction, carburisation, melting and dripping behaviour of HCI under a COH2 gas mixture using the high-temperature X-ray radiographic technique. Under 100 per cent CO gas atmosphere, the dripping temperature was 1410°C. When 5 per cent H2 was introduced, the dripping temperature slightly decreased to 1400°C. Furthermore, the dripping temperature gradually increased as the H2 gas composition increased. As 30 per cent H2 was introduced, the dripping temperature reached 1414°C. The carbon concentration in the drained metal samples gradually increased with increasing H2 composition. It is considered that H2 decreased FeO content in the slag, yielding the increased melting temperature and viscosity of the slag. On the other hand, H2 accelerated the carburisation of the reduced iron by CO gas, enabling the homogenisation of the oxide materials to form a liquid phase. Therefore, it is considered that introducing H2 in the reactor is helpful to increase productivity and energy efficiency by accelerating the liquid phase’s formation.

Aug 21, 2024

By N L. Turner, K Ehrig, V Liebezeit, D J. Robinson, L L. Kuhar, N Francis

Conventional industry tests used to determine leach recoveries are often fully monitored and may be time-consuming and expensive. Such tests may be limiting in geometallurgical applications where large numbers of samples are required to be processed for characterisation of an ore deposit. BHP Billiton currently use a fully instrumented leach test for characterisation of Olympic Dam uranium-rich samples. Researchers at the Commonwealth Scientific Research and Industrial Organisation (CSIRO) were approached to develop an alternative to these full-scale leach tests that could allow for the ranking of samples in terms of their leachability. The novel geometallurgical test was required to use samples of small mass and be affordable and rapid.Three leach test protocols were pursued in developing the small-scale tests. Kinetic leach tests were performed using mild conditions at higher pH, low temperature and low oxidation reduction potential, moderate conditions at intermediate pH, temperature and oxidation reduction potential and aggressive conditions at lower pH, higher temperature and higher reduction potential.This paper presents results from 44 leach tests on 11 samples with varying uranium mineralogy. The developed small-scale tests correlate well with data from the more costly conventional industry laboratory tests, indicating the possibility of using this alternative test as a geometallurgical leach proxy. Simple regression analysis confirmed the importance of pH, reduction potential and temperature on uranium extraction. Experimental data were fitted to published leach models to predict uranium leach extraction for a range of operating conditions.The ultimate aim of the test work is to combine a limited number of large-scale calibration tests, a large number of small-scale geometallurgical tests and leach models for geometallurgical sample characterisation and evaluation of a wide range of scenarios or processing options.CITATION:Turner, N L, Kuhar, L L, Francis, N, Liebezeit, V, Ehrig, K and Robinson, D J, 2013. Development and testing of a small-scale uranium leach for geometallurgical applications, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 345-350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By S-C Shim, H-R Lee, Y Kang, H Shin

Since iron oxide and silicon oxide are major gangue components in various types of ore, FeO-SiO2 base slag, ie fayalite slag, has been often encountered in pyrometallurgical processes of non-ferrous metals. During most matte production processes such as the smelting of Cu, Pb, and Ni, the FeOSiO2 based slag is inevitably formed and plays an important role in refining crude metal as well as engineering aspects. Recently, similar pyrometallurgical approaches have been attempted in the recovery of valuable metals (Ni, Co, Cr) from wasted secondary batteries. Thus, the viscosity of the FeO-SiO2 based slag has great significance in properly controlling smelting processes. However, when molten metal or matte does not coexist with the slag during the measurement, there has been a serious difficulty in maintaining Fe valance and consequently, the slag composition. In the present research, the viscosity of molten FeO-SiO2 slag was measured in 1573~1673 K using a rotational viscometer. In order to keep the state of iron oxides, the oxygen partial pressure was controlled using CO/CO2 gas mixture. The optimised ratio of CO/CO2 could be calculated using Fe/Fe2+ and Fe2+/Fe3+ equilibria at each temperature. The composition of the slag, particularly Fe valance, after the measurement was analysed with the aid of an inductively coupled plasma – optical emission spectroscopy (ICP-OES) and an automatic potentiometric titrator. The measurement showed that the FeO-SiO2 slag has considerably low viscosity values in the molten state, and it sharply increases as the temperature decreases. In spite of the careful oxygen partial pressure control, a part of Fe2+ was found to be oxidised to Fe3+, with a maximal case reaching about 20 per cent. The increase in viscosity of FeO-SiO2 at low temperatures can be attributed to the composition change due to an unavoidable Fe2+ oxidation. In addition, the relationship between the change in the viscosity and the liquidus temperature of FeO-SiO2 based slag was discussed to understand the composition dependence of viscosity.

Jun 19, 2024

By A M. Ebbels

"Underground mine scheduling decision-making has been based on production requirements, equipment productivities and the mine planner’s instincts on the best scheduling strategy for the mine to optimise the net present value (NPV) of a project.In the last few years, innovative software has been developed to optimise underground schedules based on NPV. The schedule optimisation tool (SOT) allows the user to set up scenarios based on grade, metal content, capital and operating costs.This paper discusses the results of two case studies undertaken using the SOT software to optimise the NPV of the projects.In each case study, the SOT software has been applied in two ways:using the original mine planner’s scenario and determining whether the NPV could be improved by changing resource capacitieschanging the scheduling goals to determine whether a different mining strategy would have a better NPV outcome.The outcomes of the case studies demonstrate that the mine layout and design were contributing factors to the overall improvement of the NPV and that SOT has a more noticeable impact on the NPV of projects where less sequence constraints are required, such as geotechnical sequencing and access development.CITATION:Ebbels, A M, 2016. Optimising underground mining strategies, in Proceedings Project Evaluation 2016, pp 60–65 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By See G. T

Bentonites and fuller's earths from seven localities in N.S.W. have been analysed with respect to occurrence, mineralogy and physical properties and areas for future prospecting have been indicated.INTRODUCTIONThe rapid expansion of Australian industry in the postwar years has been accompanied by an ever increasing demand for fuller's earth and bentonite, but in New South Wales at least the demand has been met principally by imports. However, some local and generally inferior active earths have been won to blend with imported materials to reduce costs. The important discovery of the widespread distribution of bentonite clays in the Northern Coal Measures, made recently by Grim (Booker, 1956), has givenimpetus to the further search for material comparable in quality to the imported active earths.Bentonite may be defined as a highly plastic clay, generally possessing swelling properties, composed essentially of montmorillonite and derived from the alteration of volcanic ash. Fuller's earth refers to any clay which, with or without chemical treatment, is capable of decolourizing mineral or vegetable oils and is, therefore of economic value. Montmorillonite is the active component of most fuller's earths, though palygorskite-, halloysite- and even kaolinite-rich clays have been used.Previous literature related to the New South Wales deposits has been confined to general descriptions and little technical data beyond an occasional chemical analysIs have been available. Bentonites and fuller's earths from seven...

Jan 1, 1959

By Sharmil Markar M

Ballarat Goldfields Limited is currently re-opening the old workings of the East Ballarat Goldfield which contain an estimated 1800 ML of groundwater. The disposal of this 'minewater' was of concern: the minewater is of moderate salinity; increased salinity levels have interfered with agriculture and water use at a number of locations downstream from Ballarat. Extensive numerical studies indicated that treated minewater could be discharged into the Ballarat Creek system for dilution by sewage effluent and by surface runoff after rainfall events. An automatic real-time salinity management system has been developed to enable the disposal of saline minewater in this fashion. A desk top computer operates the system: discharge and salinity readings are taken automatically each hour and filed away; the maximum allowable rate of discharge of treated minewater is calculated; pumps are switched on and off. The system readily enables daily, weekly and monthly data reports together with floppy disks of 'raw' data to be prepared in formats suitable for direct submission to the Victorian Environmental Protection Authority.

Jan 1, 1990

By Oda Y, Hashiuchi M

In the smelting section, flexible fuels such as coal or coke are used in place of heavy fuel oil in order to utilize energy sources more efficiently. Heat recovered from the off gas of the furnace has been converted by the waste heat boiler into steam, which is used for self power generation and for heating or maintaining various temperatures. The amount of the recovered steam in the smelter is currently increasing due to maximum utilization of powdered cokes. The heat source required to maintain the temperature of the electrolyte in the tank house is electric power and steam. However until recent year this steam was provided by its own heavy oil combustion type boiler in the tank house since the amount of steam consumed in heating the electrolyte is large. Though experimental work over the last few years has shown the advantages of reducing steam in the tank house by fully covering the cell, the implementation of the full cover can lead to other operating problems. However various improvements, mainly the covering of the cell with a simple device, have led to greatly reduced steam consumption. As a result, steam for the tank house is now provided by the waste heat boiler only bringing more efficient energy usage.

Jan 1, 1987

By Lee H. G, Li H, Hayes P

Slag from the smelting of lead can contain up to 20 per cent zinc as an oxide. An understanding of the lead smelting process and of the subsequent fuming process for the recovery of zinc is enhanced by a knowledge of the activity coefficient behaviour of zinc oxide in smelting slags. The literature presents a wide range of contradictory values. This paper critically reviews the published data and outlines new measurements being made by the authors. A consistent set of zinc oxide activity coefficient data is presented for liquid slags within the ZnO-'FeO'-CaO-A1203-SiO2 system, through a combination of present and previous measurements.

Jan 1, 1993

By M Behrens, A McPhee, B D. Hegan

This paper describes the design and construction of twin 400 m long road tunnels as part of the Northern Motorway Extension Project in Auckland, New Zealand. Construction of the tunnel civil works is now completed and installation of mechanical and electrical systems is well underway. The tunnels are expected to be open for traffic at the end of 2008. The paper will address the design aspects of the project including: tunnel alignment and cross-section, geotechnical conditions and rock support, waterproofing and concrete lining and fire and life safety. The paper will cover the bored tunnel section, the cut-and-cover tunnel section, cross passages and portal structures. The design brief included a requirement for the tunnels to be a gateway to Auckland and this required particular attention to be given to the visual appearance of the finished tunnel structure. The final arrangement of the portal structures and a requirement for recesses in the concrete lining for emergency cabinets, deluge pipework and cable runs, reflects these requirements. The tunnels were excavated by a roadheader and road planer using a heading and bench. Initial support was provided by a combination of lattice girders, cement grouted rock bolts and steel fibre reinforced shotcrete. The permanent lining consisted of installation of a drainage geotextile and waterproof membrane, followed by cast in situ unreinforced concrete. Each portal consists of a cut-and-cover section. This paper describes the tunnel construction methods, including the particular requirements for safety, the environment and community relations. The tunnel is fitted with a compartmentalised deluge system for fire fighting purposes. The tunnel control centre is incorporated into the control centre for Auckland Harbour Bridge, some 30 km from the tunnel location.

Jan 1, 2008

By E R. Ramanaidou, M Wells

The aim of this paper is to summarise all known Phanerozoic ooidal ironstone deposits worldwide, including Australian deposits such as the well-known channel iron deposits (CID). Nearly 400 occurrences have been catalogued based on stratigraphy, geographical coordinates, facies, grade, tonnage and iron bearing ore minerals. The description also includes details on the geochemistry, genetic models and main references. Brief statistical analysis provides an overview of the variation between these deposits. This compilation offers a basis for better understanding of the ooidal ironstone deposits and a global evaluation of this important resource worldwide.

Jan 1, 2009

By A M. Lechner, S Arnold, M J. Gillespie, P D. Erskine, D R. Mulligan, A T. Fletcher, A Gordon

Mine ecological monitoring schemes are often conducted only to address compliance and in some cases do not have the sufficient statistical power or understanding of ecological systems to assess, quantitatively, the meeting of rehabilitation targets or mine impacts. Monitoring schemes for rehabilitation commonly rely on analogue sites or premining baselines (reference sites) to assess whether rehabilitation sites are ecologically similar and thus successfully rehabilitated. In the case of monitoring for mine impacts, if the impacted sites diverge from reference data, the site is considered to be impacted. Fundamental to any monitoring scheme is testing the sampling design to ensure that it can detect these differences if they are present through adequate sample sizes (ie statistical power). However, a good understanding of the ecological system is required to ensure that differences detected are ecologically significant. Modelling ecosystem properties can provide a quantitative understanding of how ecosystems change over time and space, in response to natural environmental variations and thus aid in determining significant ecological differences. Furthermore, modelling methods can be used to predict future ecosystem states. Within the ecological literature, guidelines for robust statistical monitoring designs and modelling methods exist but are not routinely being used in the mining industry. This paper uses simple examples to discuss: problems with current compliance monitoring methods; importance of robust statistical techniques; and how modelling can assist rehabilitation assessment and guide monitoring schemes. The aim of this paper is to describe general monitoring and modelling methods that could be potentially used for mine site monitoring and closure assessment. These methods are often considered by mining companies as an extra expense that provide little practical benefit, and the domain of academia; however, engaging these methods may be more cost-effective in the long-run than conducting untargeted monitoring schemes that give no confidence to regulators on whether rehabilitation criteria have been met. Furthermore, monitoring programs in mining contexts provide a good opportunity to better understand long-term ecological patterns and test the application of more rigorous modelling approaches as the life of many mines tends to be greater than ten years.CITATION:Lechner, A M, Arnold, S, Fletcher, A T, Gordon, A, Erskine, P D, Gillespie, M J and Mulligan, D R, 2012. Embracing modern ecological methods - Monitoring and modelling for mine closure, not compliance, in Proceedings Life-of-Mine 2012 , pp 25-32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation: W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

By L Thorburn

In 2009, the Queensland Government developed a series of amendments to environmental authorities (EAs) for mines throughout the Fitzroy Basin in response to studies that assessed the cumulative impacts of mine water discharges in the basin. One of the key amendments was the requirement for all mines in the Fitzroy Basin to develop and implement a receiving environment monitoring program (REMP). The intent of the REMPs was to provide baseline information on the condition of the receiving environments of the mines and any impacts resulting from release of mine-affected water. Since this time, the requirement to complete a REMP has been incorporated into new or revised EAs for mines (including metalliferous mines) in other regions, as well as for other industries that discharge to natural watercourses (such as coal seam gas). This paper discusses the approaches that can be used to incorporate biological monitoring and direct toxicity assessments into REMPs. It highlights the importance of collecting biological data using sound experimental design principles to investigate whether releases resulted in environmental harm; and the use of monitoring data, coupled with direct toxicity assessments, for setting more realistic, site-specific trigger values and release limits (compared to the default guidelines such as Australian and New Zealand Environment and Conservation Council (ANZECC), which may not be appropriate to the region). Implementation of a robust REMP can maximise outcomes for both the proponents and the environment.CITATION:Thorburn, L, 2013. Receiving environment monitoring programs - making the most out of biological indicators and direct toxicity assessments for monitoring of aquatic ecosystems, in Proceedings Water in Mining 2013 , pp 143-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

Gold was discovered at Waihi in 1878. In 1987 the modern Martha Mine opened in the middle of the town of Waihi. Newmont Waihi Gold as the current licence holder has been operating the mine since 2000. The current open pit was scheduled to stop production in mid 2006. An underground mine is currently being developed to the east of the town.   In 2001 serious subsidence issues from historical underground mine workings outside the mining licence and the forecast closure of the open pit acted as a catalyst for the development of new communication initiatives.   In this context Newmont Waihi Gold and the Hauraki District Council initiated a community consultation process with the people of Waihi. The Waihi Community Consultation Committee (WCCC) was established in May 2003. After an initial brief to act as a forum for community participation in closure and rehabilitation of the Martha Mine, the group quickly took on a much more proactive role working towards the long-term social, environmental, cultural, economic and spiritual sustainability of Waihi.   In the course of over three years of meetings all groups represented on the committee have presented their views, developed ideas and established an organisational structure to bring those ideas to fruition. The challenge now is to work together to consolidate likely options, seek sources of funding, produce business proposals and implement the plan for the future of Waihi.   This paper backgrounds the experience to date and describes the outcomes of the process. For more detail on process considerations this paper should be read in conjunction with Part C by process facilitators, T Clark and S Stewart. For more detail on progress towards the groupÆs goals and future possibilities, this paper should be read in conjunction with Part B by Vision Waihi Trust CEO, E Morrow.

Jan 1, 2006

By D Judkins N OÆLoughlin

"Basin Minerals Limited commenced exploring for conventional strandline hosted mineral sands (rutile, ilmenite and zircon) deposits in the Murray Basin in April 1997. This has resulted in the discovery of a major mineral sands field in the Douglas Project area, located southwest of Horsham in the Wimmera Region of Western Victoria. After the successful completion of a pre-feasibility study on these deposits in September 2000, the Douglas Project has advanced to bankable final feasibility study. This study should be completed by mid-2002 to allow a decision to commence production in 2003 at an expected rate of in excess of 500 000 tonnes of combined mineral sands products per annum. The field comprises several mineralised strandlines. The main ones of economic interest are from west to east, the four strandlines, Acapulco, Bondi, Bondi East and Echo. These strandlines at August, 2000 contain total Inferred Resources of 443 million tonnes at 4.7 per cent HM at a one per cent HM cut-off; ie 20.8 million tonnes of heavy mineral concentrate which in turn contains 11.3 million tonnes of ilmenite and leucoxene, 1.3 million tonnes of rutile and 1.6 million tonnes of zircon. The heavy mineral concentrate is coarse-grained with mean diameter grain size of the strandline deposits ranging from 130 to 160 microns in size. Major controls on the formation of mineral sands deposits in the Murray Basin are discussed with reference to the main mineral sand bearing, strand plain domains; the Central Strand Plain, the New South Wales Strand Plain and the West Wimmera Strand Plain. The Douglas Project deposits on the West Wimmera Strand Plain domain are characterised by wide zones of mineralisation with high-grade cores (>10 per cent HM), low stripping ratios, and a valuable economic heavy mineral suite comprising 60 to 80 per cent of heavy mineral concentrate. Constituent mineralogy of the heavy mineral concentrate of the overall deposits is; ilmenite (40 to 58 per cent), leucoxene (five to seven per cent), rutile (four to ten per cent) and zircon (four to 14 per cent). The Douglas Project Area appears to be endowed with significantly enhanced levels of heavy minerals compared to other areas of the Murray Basin due to its unique palaeo-geographical position. Long shore drift to the south of the basin has caused large quantities of heavy mineral to be trapped against the palaeo-cliffs and headlands of a rugged palaeo-coastline which includes in a major embayment, the Grampian Mountains, the Black Range and the Glenelg Complex. To the east, major faulting and uplift has brought the fine-grained WIM offshore deposits close to the surface and has resulted in erosional stripping of mineralised strandline deposits. This mineralisation has been recycled and reconcentrated within the younger strandlines to the west within the adjacent Douglas Project Area. These strandlines are thought to be younger than other mineralised strandlines discovered to-date in the Murray Basin. The Project Area strandlines are described; ie their morphology, geology and patterns of mineral distribution. The mineralogy of each of the strandlines is distinctive and variations are noted along strike and section."

Jan 1, 2001