Search Documents

By K J. Riihioja, E Nozawa

SmartTag is a radio frequency identification (RFID) based technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and finally into the concentrator. This paper presents current developments and the future direction of the SmartTagÖ ore tracking system, as well as presenting some case studies. Successful applications of the SmartTag system have encouraged development to allow the system to be used in a wider variety of plants, in particular plants with finer crushing and screening stages. This presented Metso with a number of technological challenges, including RFID tag and antenna design. By reducing the traditional RFID tag diameter from 60 mm to 20 mm the RFID tags can now successfully pass through a secondary crusher. The new smaller RFID tags (referred to as mini RFID tags) have been used in some Process Integration and Optimisation projects with very promising results. The results indicate that the miniature RFID tags have a higher survivability to blasting and through secondary crushing stages. Extending ore tracking further through the process allows more reliable linking of spatial data with time based process performance. Metso is looking at developing even smaller micro RFID tags, and is also investigating other applications for the SmartTag system, including ore tracking from the original source to the final destination (ie from the mine, through the plant and ports to the customer).

Sep 26, 2011

By E J. Hill, F Huang, A Otto

Geochemical data from drill core samples is used in mineral exploration to enable geologists to understand subsurface geology. However, it is challenging to analyse these data sets rigorously and consistently. Manual data interpretation relies on the knowledge and experience of logging geologists. When multiple geologists are involved, it is possible to introduce inconsistencies in logged lithology type and scale of logging (‘splitters’ versus ‘lumpers’). Machine learning (ML) is a powerful tool for analysing high dimensional data (ie data with many variables) and large data sets (ie data with many samples). However, ML methods applied to drill hole samples do not incorporate spatial information and this can result in high misclassification rates and small-scale ‘noisy’ results. We demonstrate the use of multiscale spatial analysis (wavelet tessellation) as a pre-ML step to analyse spatial information. This step helps reduce misclassification and filter out unwanted small-scale variation in the data. In an experiment, we used wavelet tessellation and supervised ML to predict litho-geochemical rock types from geochemistry data. The data set is from the Valhalla uranium deposit near Mount Isa, northern Queensland. First, geochemical knowledge and statistical analysis was used to select appropriate geochemical elements for litho-geochemical classification. Second, the elements were processed using multiscale spatial analysis. Third, we trained a Random Forest model with the data set and found that the model performs worse in predicting rare rock samples than common ones. We applied over-sampling and down-sampling methods in aim to overcome this issue. As a conclusion, the combination of multiscale spatial analysis (to define rock unit boundaries) and Random Forests (to classify rock units) is a good method for rapid and accurate analysis of drill hole geochemistry.

Mar 22, 2022

Waihi Gold Mining Company Limited, a wholly owned subsidiary of Normandy Mining Limited, operates the Martha gold mine, located in the township of Waihi, New Zealand. The operation, an unincorporated joint venture, comprises Normandy Mining Limited (67.070/0) and Otter Gold Mines (32.94%). Since gold was first discovered at Waihi in 1878, it has formed a key part of the region's economy. In 1909 the Waihi mine was described in a report to Parliament as æthe most important gold mine in Australasia and one of the greatest in the world.Æ That was a record year for production, with 416,813 tons of ore mined and some 1,120 men employed. Today the mine produces up to 1,250,000 tonnes of ore annually, and the project employs some 234 men and women. In 1999 the value of the gold and silver produced ($59 million) made up 47% of Waihi's estimated GDP. Waihi Gold has made significant contributions to the Waihi economy, community and the Hauraki region as a whole. Since the mine was re-opened in 1987, thousands of local people have benefited from the mine. In 1999, consents were granted allowing an extension to the mine life (the Extended Project) and this will result in a further seven years of economic benefits resulting from mining activity. The Company has undertaken extensive consultation throughout project planning, construction, operations and rehabilitation. Ongoing liaison and involvement with all community sectors, including Tangata Whenua and Iwi, local residents, recreational groups and schools remains an integral part of the operation. Throughout the life of the modern Martha Mine, the Company has actively supported the local community in the form of donations, sponsorships, the provision of amenities, and by participating in community events. A well established environmental team exists at the site. Environmental and community performance is measured by an independent five-assessment process, and the Company is committed to achieving excellence through ongoing improvement programmes and staff awareness. When the mine is closed, the open pit area will be transformed into a recreational lake, and the tailings storage facilities will be rehabilitated to become a combination of wetlands, grassed areas and ponds. Resources will be provided by the Mine to ensure the rehabilitated site remains in a safe and self-sustaining, stable condition in perpetuity. The mine is regarded as a showcase on a world standard of how a modem mining operation can successfully coexist with the nearby community.

Jan 1, 2000

By N Elith

The explosives demolition of a post-stressed, steel reinforced, concrete road bridge in Australia’s capital city, Canberra. The bridge was 50 m from the new replacement bridge, 320 m from community structures and within five kilometres of the national parliament buildings. The job required multiple overlays of risk assessment, public relations, safe work procedures, specialised blast design, environmental predictions and flyrock controls. Project stakeholders included Worksafe, Roads ACT, bridge owners, consulting structural engineers, community groups and road users. The bridge precincts, including a major road underneath, had to remain operational to peak traffic in the days leading up to the demolition. The break-up and removal of debris had to be executed in just two days from Friday to have the road beneath re-opened for Monday morning city-bound traffic.In Canberra, all explosives demolitions are now viewed with particular caution after a demolition in 1997, during which a young girl was killed. Any approval requires that Explosives Regulations, AS2187 2006 and Worksafe processes are satisfied, and a convincing case presented for blasting as a safe and viable option.Our design used specialised shaped cutting and blasting charges to sever in situ concrete beams and tendons and to shatter components of the stressed concrete bridge assembly. We include comments on structural engineering reports dealing with pre-weakening mechanisms. The benefit of pre-weakening is that it reduces the amount of explosives needed to safely complete the job and facilitates quick removal of debris after the shot. The complementary skills of the team, each one an expert in his field, resulted in a highly successful demolition, praised by authorities as an outstanding example of controlled use of explosives.

Nov 8, 2011

New Celebration Gold Mine is located 35 km SE of Kalgoorlie, Western Australia, in the Archaean Kalgoorlie-St Ives Greenstone belt. The leases total 119 sq kms and arepart of a joint venture between Newmont Australia Ltd (as manager) and Mt Martin Gold Mines N.L. Mining commenced in August, 1986 and is now producing over 115,000 ounces of gold per annum. A variety of gold mineralisation styles with a total resource of 23.5 million tonnes at 2.19g/t are associated with shear zones at New Celebration. Gold production is co-ordinated from 7 open pits with others planned to com- mence soon. A large scale underground trial mining operation has com- menced with a decline on the hanging wall of the main producing orebody, Hampton Boulder. Millfeed produced is classified on the stockpile according to grade and metallurgical performance and blended tomaximise throughput while main- taining grade through a CIL treatment plant currently operating at 1.7 million tonnes per year.

Jan 1, 1991

By N M. Player, R P. Varden, E Jones

"An effective geotechnical design provides an accurate and appropriate assessment, balanced with a mining company’s risk profile. Justifying the cost of slope assessment requires an understanding of the input sensitivities, and resultant risk, to achieve a slope of a required functionality. As a project progresses from Scoping to Feasibility, the geotechnical risk becomes better resolved through increased expenditure on drilling, testing, analysis and modelling as long as the input data is appropriately spatially distributed. Providing accurate and appropriate geotechnical assessments in the early stages provides confidence in all following stages, especially where initial analysis indicates difficult geotechnical conditions. It is also in the early stages of project definition that there is most opportunity to maximise the value of the deposit through investigations into optimal mining methods.This paper examines the advantages of geotechnical engineering input through a project study period. Early geotechnical involvement allows the Scoping and Pre-Feasibility Studies to be more effective. Operational risks can then be better understood and dealt within the Feasibility Study phase, also ensuring that the correct risks and management controls are put in place.With commodity price pressure and cost of resource recovery in a downturned industry, reducing the risk to cash flow, resource recovery and safety should be a primary goal for all mining companies. Reduced risk can be effectively achieved through geotechnical design of slopes to achieve a required performance as part of an integrated study to the Reserve definition and mine design.Citation:Varden, R P, Player, J R, Player, N M and Jones, E, 2016. Justifying Slope Design Risks and Costs, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 185–201 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By R Knight

The spatial variability of geometallurgical characteristics in a mineral deposit can have significant impact on financial and mine planning, mineral processing, concentrate quality and tailings composition throughout the life of a project. These characteristics that may determine the success of a project are not readily apparent to geologists unless they are integrated with deposit geology and assay data, modelled in 3D and incorporated into resource block models.One of the primary objectives of geometallurgy is to integrate and incorporate various geologic, geotechnical and geometallurgical parameters into resource block models, which typically are limited to in situ tonnes and grade of economic metals. Critical attributes, such as concentration of deleterious elements that affect the project viability need to be identified and integrated into the resource block model early in the exploration stage to predict project profitability and address potential environmental impacts.Using data from a volcanogenic massive sulfide deposit we present an example of the integration of ore geochemistry (cadmium, arsenic and antimony) with the results of preliminary, bench-scale metallurgical test work in a 3D geometallurgical model that predicts subdomains of poor-quality concentrate and tailings containing environmentally-sensitive elements. This critical information was incorporated into the existing resource block model in order to inform both financial modelling and mine planning.This example demonstrates that geometallurgical data can be effectively integrated with geological and assay data using Leapfrog MiningTM software (Leapfrog Mining) early in the exploration stage of a project. Three-dimensional representations of geometallurgical data can be created directly using primary additive data, as well as from proxies of non-additive parameters. Resource block models can be updated continually with new information as the project passes from exploration through production. In addition, the software allows for 3D visualisation of the characteristics of the materials that will eventually constitute the mill concentrate, tailings, and waste. This study emphasises the critical importance of establishing a systematic geometallurgical approach early in the exploration stage that can be continuously updated with new information throughout the life of the project. In the example that we present, sulfide ore that had otherwise been identified as high-value (in the absence of geochemical and metallurgical data) turns out to be low-value ore due to concentrate penalties and increased environmental impact.

Sep 5, 2011

By N Lefebvre, M Jakeman, R Aseervatham

Semi-arid regions suffer from two afflictions; evaporation may exceed precipitation by multiples of two or more and variations in precipitation can be both extreme and difficult to predict. Many Australian mines are situated in semi-arid areas where communities are reliant upon locally sourced water or special purpose infrastructure is built as part of the mine construction. As the question of climate change looms, issues related to future water supply and sustainable water management become increasingly important. Across Australia several mining operations co-exist in a single surface water and/or groundwater catchment area. The management of water on a mine by mine or a community by community basis is illogical and must be reconsidered based on a single water catchment and a whole-of-community basis. Mine water should be considered on a full life cycle basis where the quality is assessed for specific mine site applications. This paper addresses technical challenges that include surface water and groundwater supply in semi-arid regions, operational water in the mining industry, beneficial uses of water, water economics and demand management. In much the same way as emissions trading evolved into a multi-stakeholder forum, mining regions offer scope for innovative thinking in water supply and reuse. In addition, this paper considers a number of initiatives taken by Australian mining companies that are entering a prefeasibility stage and contrasts these initiatives against the established success within a South African mining region. The challenges and potential solutions to this initiative are presented for future consideration.

Jan 1, 2006

By G Reynolds, L Lu

Queensland Pacific Metals (QPM) is developing its flagship Townsville Energy Chemicals Hub (TECH) facility to produce nickel and cobalt sulfates from imported high-grade nickel laterite ore for nickel-cobalt-aluminium and nickel-cobalt-manganese Li-ion batteries. The TECH facility is expected to use a patented leaching, recovery and recycling process called the DNi Process™. It uses the nitric acid leaching process for extracting nickel, cobalt and other valuable metals from laterite ore. Apart from the nickel and cobalt sulfates, the TECH Project will also produce high purity alumina, hematite (~640 ktpa) and other by-products. The hematite by-product precipitated from the DNi Process™ (hematite precipitate hereafter), is high in Fe and particularly low in impurities. QPM is working to identify potential applications for these high-purity by-products to generate additional revenue and to achieve its zero-waste ambition. As such, QPM has engaged CSIRO to evaluate various agglomeration options to produce low-cost, hematitic products suitable as ironmaking feed materials. This paper will first reveal the unique characteristics of the hematite precipitate arising from the TECH Project and then examine the sintering and pelletising processes for preparing the hematite precipitate as an ironmaking feed.

Sep 18, 2023

By C Lower

An unprecedented, quantitative, deposit-scale understanding of major clay mineral distribution throughout the Yeelirrie uranium deposit has been achieved by adapting the existing HyLogger™/HyChips™ analytical technique to measure resource assay pulps. Spectral analysis via HyLogger™ and HyChips™ systems has previously been used as a small-scale geometallurgical research tool, but never before has it been quantitatively applied to an entire resource sample population for the purpose of developing stand alone block models for major clay minerals. Economic uranium mineralisation within the thin but extensive Yeelirrie?palaeochannel?primarily exists within the transition zone between a groundwater-derived calcrete and the underlying clay-quartz regolith. Early geometallurgical investigations identified that certain clay minerals could be deleterious to the efficiency of the uranium recovery process. Accurate calculation of clay mineralogy from resource assays proved too difficult due to chemical similarities between co-existing kaolinite, smectite and magnesium carbonate minerals. A relatively low-cost, efficient and accurate method of quantitative clay mineral analysis was required to measure over 70 000 resource assay pulps. After initial testing and comparison with QXRD, the HyChips™ 3-1 spectral logging system was implemented as a primary method of clay mineral analysis for the Yeelirrie uranium deposit. The resultant spatial data set allowed the interpretation and geostatistical analysis of geometallurgical domains across the deposit. Clay block models were generated and used in geometallurgical resource calculations to benefit the mine planning process.

Sep 5, 2011

By T Wellman, G Sternadt, R Hingston

The 335 000 oz Wilber Deposit is located within the Meekatharra-Wydgee Archaean greenstone belt in the Murchison District of Western Australia. The deposit comprises high-grade gold mineralisation hosted within a steeply west-dipping quartz lode, which lies within a broader (20–60?m) north-east striking shear zone envelope. Locally, the northerly-trending host rock geology includes greenschist facies high-Mg basalt (albite, actinolite, chlorite, biotite, calcite, zoisite, muscovite and titanate) intruded by at least two generations of felsic to intermediate porphyries (albite, actinolite, zoisite, chlorite, sericite, biotite, quartz and titanate). The Archaean rocks are cross-cut by a number of east–west striking Proterozoic dolerite dykes (biotite (50 per cent), albite, carbonate, epidote, titanate and actinolite) that are interpreted to have intruded pre-existing regional structures. The entire mine package is cross-cut by a system of shallow north-east-striking, north-west-dipping, barren quartz veins that commonly contain large (up to 30 cm), euhedral, smokey quartz megacrysts.The north-east-trending lode lies within a 3 m wide shear zone and varies from a single discrete 0.5 to 4 m wide laminated, massive or brecciated quartz-carbonate vein to multiple laminated veins up to 1 m wide within the shear. The veins exhibit strong boudinage, with cross-cutting quartz-carbonate seal veins in the boudin necks. The boudin necks often contain pink calcite. The shear zone fabric wraps closely around the boudin necks proximal to the vein, becoming more lode parallel distal to the vein. The lode is offset by a north to north-north-west trending fault.Mineralisation occurs as free gold within the quartz carbonate veins, with accessory sulfides including pyrite ± chalcopyrite, ± galena ± sphalerite. Fuchsite is observed in the veins, as laminar wall rock inclusions, with visible gold commonly associated with the wall rock laminations.Gold grades range from less than 1 g/t within the hosting shear zone, either at the margins or interstitial to the veins, to approximately 30 g/t in the single vein, and up to greater than 60 g/t in the multiple vein areas. Gold is commonly visible and disseminated throughout laminated, breccia and massive quartz veins, although laminations show the highest concentration of gold grains.CITATION:Hingston, R, Wellman, T and Sternadt, G, 2014. The geology of the Wilber Deposit, Andy Well Gold Project, Murchison District, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 55–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

Mobile mining equipment presents only a small portion (ten per cent mining project costs but the selected technology will determine to a large extent the mining performance and mine profitability. The actual performance of the selected mobile equipment technology will rely on the support functions, infrastructure, user interface and user acceptance. Optimising the technology to match the circumstances is an increasingly important phase in a mine feasibility study. Smartly done feasibility studies include the possible future needs of changing or building-up of the selected technology. In massive mining applications the machinery faces quite different challenges than in selective or small-scale mining applications. In massive mining applications the efficient and continuous move of large amounts of material has led to the use of increasing degree of automation. This higher degree of automation in a mining application, on the other hand, will be best applied to a smooth and streamlined mining process and operation. Mining methods like block caving support automated operation. Automated mobile equipment needs supportive infrastructure, monitoring and information transfer systems as well as well established working procedures. Too often the user interface and human factor is disregarded during the consideration of automation. Through the available supplier programming tools it is possible to see how much the selected technology provides flexibility in changing production or economical situations, when major rebuilds or replacements are necessary, and view the effects of all these on the mine economy. When adequate technology is available from various sources, the difference becomes from preparing for the future, managing costs and combining the best layout with the most suitable technological solutions.

Jan 1, 2000

By R J. Romañach

The theory of sampling (TOS) is now followed in the development of near infrared (NIR) spectroscopic methods for the pharmaceutical industry. TOS has been the guiding light for a two-step approach for spectroscopic composite sampling available for the development of real-time analytical methods for particulate-based industrial processes. The two-step spectroscopic sample composite has been used in the development of process analytical technology (PAT), an important regulatory initiative to improve the quality of pharmaceutical products. The two-step sample composite approach overcomes the low sample volume analysed by PAT methods; one of the key limitations to PAT implementation in the industrial production of particulate-based materials.PAT methods need to be validated demonstrating their accuracy, precision, specificity and robustness. TOS provides a deeper understanding of these validation studies which involve discrete particulate material. The validation of PAT methods is now being performed considering both sampling and analytical errors, while practically all previous method validations only addressed the total analytical error (TAE) of these methods. This has been a crucial impediment for the field of chemometrics as well.PAT is a key element of continuous manufacturing (CM) processes, which are considered an emerging technology capable of increasing the flexibility, agility and robustness of pharmaceutical processes while reducing their costs. The outflow of the continuous process is a 1D lot, and variographic analysis has been shown to discern process variation from sampling and analytical errors in pharmaceutical CM processes. Thus, variographic analysis is a process improvement tool with significant potential for improving CM processes. The possibilities for improving pharmaceutical manufacturing are enormous.CITATION:Romañach, R J, 2017. Theory of Sampling – from missing link to key enabler for process analytical technology, in Proceedings Eighth World Conference on Sampling and Blending , pp 63–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Most new engineers in the mining industry do not realise the importance of legal obligations. During investigations the first question you are asked is: Do you have any proof or evidence? The smallest detail in an underground notebook or a diary entry is able to be used as your proof and/or evidence. The importance of a paper trail is often undervalued and overlooked when you first enter the industry. As a new engineer, all too often your legal obligations, including your duty of care are not given enough consideration. Whose job is it to inform you of what your legal obligations are and when do they end? Everyone has legal obligations at every level of the industry, from graduate to mine manager. The level of these responsibilities varies depending on the position that you hold. When you first start in the industry you need to understand what your responsibilities are and how you are expected to discharge them, whether they are memos, databases or senior sign-offs, etc. In order to fulfil your obligations you must first discharge your own obligation, which in turn discharges those of your department and ultimately those of the mine. As a graduate engineer in the mining industry what I have learnt about my own legal obligations has come directly from my own experience, which will form the basis of this paper.

Jan 1, 2007

By Kavanagh M. E, Henley R. W

The Meekatharra mining district lies in the northern pan of the Murchison Province of the Archaean Ynlgam block of Western Australia. Since dis- covery of the Paddy's Flat belt in the district in 1897 total gold production has been 67 tonnes and a further 33 tonnes in resources have been defined by drilling. The Paddy's Flat gold deposits occur within the Gabanintha Formation, a basal formation of the Murchison greenstone sequence containing komatiitic basalts, ultramafics and minor banded iron formations. The regional control on the distribution of deposits is an anastomosing shear belt which extends over 350 km and incorporates the Mt Magnet, Reedys and Meekatharra deposits. The following gold deposit styles may be recognized based on lithological association and alteration: Albite porphyry hosted, Carbonate-fuchsite- quartz alteration hosted deposits, Banded Iron Formation hosted sulphide replacement gold deposits and quartz vein deposits. With the exception of the banded iron formation hosted deposits, the Paddy's Flat alteration zone shows strong similarities to the alteration styles at Kerr-Addison (Ontario).

Jan 1, 1991

By S A. Campbell

There has been a reduction of coal production in the United States due to environmental pressure and the increased use of natural gas. This reduction will require coal producers and consumers to make decisions on whether to sample more to verify contract quality or sample less in an effort to cut costs.CITATION:Campbell, S A, 2014. The shrinking coal market in the US – sample more or sample less?, in Proceedings Sampling 2014 , pp 3–6 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

Reverse circulation (R.C.) drilling or the dual tube method as it is quite commonly known, has a unique place in conventional mineral drilling. It can be classified half-way between open hole drilling at the lower end of the scale and diamond drilling at the upper end. The system basically consists of two tubes, one inside the other, with compressed air flowing between the inner and outer tubes. Sample cuttings return up the inner tube through the head of the rig and via a hose to a cyclone where the sample is collected. This system means that the cuttings are free of contamination as they are at no time in contact with the outside formation of the hole.Reverse circulation drilling is divided into two areas: R.C. Roller and Blade for softer formations; and R.C. Percussion for harder formations.

Jan 1, 1986

By W Kendall

Ore sorting has the potential to reduce the feed to wet plants and in the case of complex orebodies that can significantly reduce the water, energy and reagent consumptions and resulting operating costs for the project. The application of ore sorters has sparked renewed interest and application in the precious and base metals mining industry in recent years as a result of the continuing development of new sensing technology and very fast information processing that is making ore sorters applicable to a much wider range of ores and larger scale operations. The application of ore sorters involves a range of trade-off decisions that have economic impact upon the benefits of ores sorting to the project under consideration. This paper will present some typical trade offs to be considered and their impact in a particular project setting. CITATION: Kendall, W, 2018. How economics drive the application of ore sorting, in Proceedings Complex Orebodies Conference 2018, pp 24–27 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Following a decline in direct and indirect employment in the minerals industry between 2000 and 2003, the situation reversed in 2004 and employment rose by 12 per cent. Furthermore, there are forecasts of continuing employment growth in the minerals industry in the immediate future. For those of us charged with promoting the virtues of a career in the minerals industry this is encouraging news, as it provides us with the evidence to promote the increasing employment opportunities of a healthy and vibrant industry. However, for many others û particularly the employers in this industry û the news is not so rosy. The jobs are there, and in increasing numbers, but the workers arenÆt! Employers right across the industry are finding it increasingly difficult to fill vacancies with suitably qualified and skilled employees and the competition is becoming fiercer. In the minerals and energy sector, questions are being asked and solutions sought on the industryÆs ability to attract and retain a skilled workforce. From many quarters û industry, government and the education sector, calls for urgent action are becoming louder. The reasons for this are well known û the nature of the work, the remote location, perceptions of the industry, an aging workforce, the gender imbalance, the shrinking demographic of school leavers. It is the latter I wish to focus on û the Generation Y demographic û those who have recently left school, those who are in higher education or have recently entered the workforce, or those who are still at secondary school. These young people are the next cohort of potential employees for the industry. But our need for them appears to be greater that their perceived need for us! How do we engage them so they are informed about the industry? How do we inform and advise them so they are prepared to consider further education and training in disciplines and skill areas relating to our industry? How do we guide and motivate them to give it their best shot and work in it û at least for part of their working life? These are fundamental questions that many within the industry have been grappling with for quite some time. Let me share with you some of the strategies that the Minerals Council is implementing to address this issue.

Jan 1, 2005

By P J. Howard, P Darvall, J H. Mainwaring

In less than a year, Atlas Iron’s Corunna Downs Project has moved from a new discovery to a substantial resource of high quality in an underexplored greenstone belt. Located approximately 170 km south-east of Port Hedland and 40 km south-west of Marble Bar, in the Pilbara Region of Western Australia, Atlas Iron Ltd (Atlas) has conducted extensive exploration work at Split Rock, Razorback, Runway and Shark Gully, consisting of geophysical surveying, field mapping, 464 reverse circulation and 16 diamond drill holes resulting in a current resource of 51 Mt at 57.3 per cent Fe (Atlas, 2014b).The Corunna Downs Project is interpreted to be hosted within the Cleaverville Formation of the Archaean Gorge Creek Group. Within the project area these rocks outcrop as subvertically dipping banded iron-formations (BIFs) and jaspilites, cherts, minor shales and meta-sediments forming a north–south trending plateau.Primary hematite-martite iron mineralisation is overprinted in the near surface environment by supergene goethite, and frequently capped with a thin laterite cover. The strongest enrichment areas have been discovered within topographic lows, proximal to fault zones, which coincide with a geophysical anolmaly. These characteristics were targeted, and the subsequent areas mapped in greater detail, allowing for efficient resource definition.Although first explored for iron in the late 1960s, it wasn’t until Atlas’ acquisition of the project in October 2012, that major strides were made to defining an economic resource. At present, Corunna Downs is Atlas’ best greenfields exploration discovery, both in terms of the potential scale of the resource and its blending capacity.The Corunna Downs prospect is emerging as a major new iron ore province in the Pilbara and includes 80 km of potential host stratigraphy. Corunna Downs sits strategically between Atlas’ Mt Webber and McPhee Creek tenements, and can play an important part in Atlas’ growth strategy as iron ore market conditions become more volatile and challenging.CITATION:Mainwaring, J H, Howard, P J and Darvall, P, 2015. Discovery of the Corunna Downs deposits, in Proceedings Iron Ore 2015, pp 305–312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015