Search Documents

By Hedge AS

Mt Whaleback is one of the largest open-cut iron ore mines in the world. Haulage cost is the single largest component of operating costs at the mine. Past studies towards alternatives to truck haulage have recognised the potential viability of an in-pit crushing and conveying system, dependent on the proportion of uphill haulage. After seventeen years of mining Mt Whaleback still contains more than 1,000 million tonnes of ore, needing 1,800 million tonnes of waste removal to extract it. What was once a quarry has now turned into a large open pit. The increasing proportion of uphill haulage, the need to replace ageing 120 ton and 200 ton trucks and the necessity of achieving and maintaining a higher stripping ratio prompted, in 1984, the initiation of a new feasibility study into the viability of alternative material handling systems. A semi-mobile in-pit crushing and conveying system was found to be most suited to Mt Whaleback conditions. The East Pit was selected as the best location based on the analysis of haulage profiles measured on long term incremental mine plans. A capacity of 22 million tonnes per year was considered achievable by the proven technology currently available. A detailed estimation of capital and operating costs of two systems - one with trucks only and another with trucks, crusher and conveyor - for the removal of 22 million tonnes per year of waste rock, showed substantial cost savings achievable by the proposed system. An economic evaluation of the two systems established the advantages of constructing the in-pit crushing and conveying system. This is now under construction and will be commissioned in early 1987. Experience gained in constructing and operating this installation is expected to influence decisions on similar installations in future.

Jan 1, 1986

In mineral asset valuation the use of any valuation method requires the input of competent and independent technical professionals. A resource valuation must be as transparent as possible to allow others to assess the validity of their underlying assumptions. Materiality is a dominant factor in all valuations and a valuer should set out the basis for the subjective decisions made in this regard. Any valuation methodology must comply with the requirements of the law, practice notes and guidelines issued by the various relevant authorities and professional bodies. The valuation methodology chosen to value a mineral asset depends upon the amount of data available on that asset and the reliance that can be placed upon those data. Mineral assets generally fall into one of three broad categories, depending upon their state of development, ie whether they are at the exploration, development or operating stage. Naturally there are transition phases. Hence, there are ""Grass Roots"" Exploration Areas and Advanced Exploration Prospects; Pre-Development Projects and Developing Mines; and Operating Mines. The features of each of these mineral asset status categories are described, mainly in terms of the confidence in the contained identified Resources/ Reserves. The various subjective methodologies available for the valuation of ""Grass Roots"" Exploration Areas and Advanced Exploration Prospects -are specifically reviewed. The pitfalls in adopting a ""recipe"" approach are noted. It is the author's view that the Expected Value Method (based on the probability adjustment of the output of a Discounted Cash Flow/ Net Present Value model) has little application in the valuation of exploration mineral assets, so it is only briefly addressed. The methodologies reviewed are listed below. ò Multiple of Exploration Expenditure Method (expenditure based). ò Joint Venture Terms Method (expenditure based). ò Geoscience Rating Methods (eg Kilburn - area based). ò Comparable Market Value Method (real estate based). ò Rules of Thumb (eg $/Resource or production unit; % of in situ value). Some recent Prospectuses are used to provide examples of their misinterpretation and misapplication.

Jan 1, 1994

By D Nourry

Optimising the blast is a major issue in the blasting business. It generally means acting on the blasting pattern (drilling, charging, detonating) in order to get a given æresultÆ. This result may either be related to economic reasons, such as the fragmentation influencing productivity, or technical reasons, for example vibrations and projections. Within the frame of the EEC funded Brite-Euram project entitled æBlast-ControlÆ, involving academic research and applied expertise, a general methodology was developed to approach such a problem and currently applied to the industrial partners of the project and final end-users of the generated results. These partners are the limestone ALZO quarry of the CALCINOR group in the north of Spain and the dolomite DMD (Dolomies-de-Marche-les-Dames) quarry of the LHOIST group in the east of Belgium. A first part of the project, over 18 months, was dedicated to establishing a clear relationship between productivity of operations from drilling to primary crushing and the fragmentation resulting from the blast. Extensive monitoring of blasting, production performance and fragmentation data was carried out and automatically collected into a database on both quarries. As expected, it appeared that excessive amounts of fines or boulders were substantially reducing productivity and thus profitability of the operation. Furthermore, an æoptimalÆ fragmentation was assessed for the quarries to run at the best (high throughput, low cost). The second and last part, for the remaining 18 months, was then dedicated to adapting the blasting practice in order to orientate the fragmentation towards a æbetterÆ one. A very common problem normally addressed by any consultant. Nevertheless, the target was not limited to solving the problem for these two quarries, but also to develop a generic method to address this blasting adaptation process and to implement it into a computerised tool. At this stage, it is then obvious that portability of the method and the system are major qualities to be looked for. This paper is aimed to present how this method was developed, how the system was implemented and how it was finally used.

Jan 1, 2001

By R Polmear, G Mauger

You wouldnÆt start excavating before testing core samples, so why would you approve a project plan before all factors have been identified, reviewed and addressed? Even a champion sports team made up of the best players canÆt produce optimal results without a well understood and agreed game plan. Could an F1 racing team produce their outstanding performance without rigorous evaluation and testing of the factors for successful performance? Why would we expect a capital works project team to be able to get it right without an understanding and an involvement in setting and implementing the overall game plan and without an understanding of all stakeholder requirements? For International PowerÆs Hazelwood (IPRH) mine in Victoria, the challenge was development and delivery of a 40 year mine plan, ultimately involving relocation of existing mine operations into an adjacent new coal field, land acquisitions and major environmental and other approvals to allow diversion of three streams, a highway, an Over Dimension route and other infrastructure in a political and environmentally sensitive atmosphere. The lessons from International Power HazelwoodÆs (IPRH) experience are: that the clear set of project principles and guiding values ensured delivery of a robust plan; a robust plan can withstand significant change; and value management (VM) played an important role in providing assurance, to all, that the plan was sound at both the strategic and micro levels. This Hazelwood mine project included five major VM workshops. The first was a critical review process in addition to design and cost reviews. This VM workshop was used to analyse, at a high level, the preferred coal mining sequence and design concepts, together with the interaction between design elements, risks and costs. In addition to this, the workshop provided an agreed common pathway for all downstream decisions. A second VM study was conducted to ensure that the proposed plan and design for relocation of the conveying systems from the existing mine into the new field were planned for optimum achievement from a whole of life cost, time, operational and maintenance perspective, plus the logistics of continuing operations while relocating assets. A third study followed to review the Conveyor Transfer Alliance and review functional design. A fourth VM study workshop was formed at the start of Phase 2 Alliance to ensure that the best value for money was being achieved through the current design, schedule and project arrangements and that all interfaces between parties had been reviewed and responsibilities were clear and understood. Other studies are outlined later in this paper. This paper details the evaluation criteria and processes used in the project evaluation that led to the WestField Mine Development.

Jan 1, 2007

By G Kuntz, V Wall, B New

The prime aim of the Campbell Mine project was to develop a 3D geological model for the Campbell-Red Lake system to contribute to an exploration model for the region. The base data is composed of over 60 years of geological data covering an area of 16 by 8 km, and from surface down to 1830 m depth. This paper concentrates on the methods used in the GeoSpace system for the processing, integration, display and interpretation of such a large and diverse data set. A block model was developed that recorded the relative frequency of each geological feature within each block. The data input for the block models were based on recoding of the Campbell Mine drilling and channel sample databases into lithological, alteration and structural subsets. The value for each geological characteristic inserted into each block is calculated from all available data that falls within the block. Relative and absolute comparisons of the individual variables provide a targeted outcome from which the blocks are coloured for visual inspection. Different combinations of variable comparisons can be evaluated so that required features are highlighted for interpretation. Blocks are displayed to illuminate the ædominantÆ rock type, according to a formula that may be varied interactively to display the features required by the geologist. This flexibility allows rapid remodelling of lithological distributions, commonly highlighting minor lithological packages not readily visualised in, and interpreted from, drillhole traces alone. The 3D geological model was built from the drillhole datasets and old mine plans utilising standard 3D mining, GIS and database software, with several iterations of plan and sectional interpretation. Near surface bedrock geological interpretations were further constrained by low level aeromagnetic data. The Geospace approach employs an innovative technique for visualisation of the distribution of lithological packages and alteration via block modelling. The method utilises the block model format of data handling as it is considered to be more visible than drilling, flexible enough to incorporate a wide range of data sources, and allows for spatial proximity relationships to be investigated. The method is a simple form of processing large data sets so that results are clearly visible. The calculation is much more rapid than estimation procedures, and does not have any requirement for geostatistical interpretation which is also time consuming. Geospace is not unique to any mine environment software and it is expected to be able to be performed in any system. The proper portrayal of the internal structure of the mineralised body will provide practical input to exploration and mining principally in the areas of resource estimation, exploration vectoring and ore/waste characterisation and may be incorporated with other data to include mine support and mine scheduling.

Jan 1, 2003

By C McInnes

The key to successful flotation plant design, production planning and mine/mill optimisation is a solid understanding of the resource to be processed. As advocated by the authors of this paper, the main components of geometallurgical modelling of an orebody and its associated flotation plant are: an ore sampling program and subsequent laboratory testing of these samples in order to extract process model parameters; geostatistical distribution throughout the resource model of the process parameters; calibration of the plant via benchmarking (for existing operations); and plant simulation using a system of process models and the distributed metallurgical parameters (from step two) as the data set.It is important that the grinding and flotation models are linked. For example, a laboratory test conducted on a drill core sample, intended to represent a portion of the orebody, is conducted at a specific grind (represented by a P80). However, when that ore is actually processed through the plant it may well be (and in many cases most likely will be) at another P80. Additionally, the flotation plant residence time will often be determined solely by the grinding circuit capacity and feed slurry density. In the case of SAG mill û ball mill circuits, the fluctuations in tonnage and grind are known to be high. The modelling approach described in this paper allows for changes in the measured flotation kinetic parameters in order to reflect the expected grind as determined by the comminution process.

Jan 1, 2005

By Kuzugundenli OE, Nagaraj DR

Organic complexing agents have received special attention over the past few decades in the search for reagents for improved flotation separation of minerals, especially non-sulphides. The majority of such reagents that have been proposed over the past few decades have remained largely a laboratory curiosity, except perhaps alkyl hydroxamates, because their selection is seldom based on commercial viability. In this regard, the choice of complexing agents such as oximes may be more realistic because of their widespread use in solvent extraction of copper. Our earlier studies have confirmed that they are also effective as collectors for copper oxide minerals, including chrysocolla which is the most difficult copper mineral to beneficiate. The flotation behaviour of chrysocolla for several structurally-related hydroxyoximes were studied as a function of pH and oxime concentration and the role of structural features examined. The structural changes studied included substitutions in both chelating and non-chelating parts of the molecule. The results indicated that, contrary to expectations, many of the structural changes in the basic molecule, salicylaldoxime, do not have a positive effect on collector efficiency. The reduction in collector efficiency is rationalised on the basis of possible steric factors affecting complexation and packing of the collector species on the mineral surface as well as effects due to changes in electron density brought about by substituents. Introduction of alkyl substituents on the oximic carbon of salicylaldoxime yielded the highest collector efficiency.

Jan 1, 1993

In the last two decades, equipment used in the coal mining operations has become much more sophisticated. The way that work is organised and performed in the industry has also changed significantly. Changes in equipment specification or procedures inevitably means that the risk associated with that equipment or procedure also changes. In an attempt to address this the Joint Coal Board Occupational Health and Safety Trust (JCB) commissioned the University of New South Wales Mining Research Centre and Mine Site Technologies to perform a feasibility study into the development and deployment of Virtual Reality (VR) based training simulators in the New South Wales coal industry. The main aims of the study were to identify, the key providers of VR Technology, the VR options available to the JCB and the information that would need to be included in any simulator. It was anticipated that a critical assessment of these components would produce a format for a cost effective, state of the art simulator that could be readily accessed by all mines. The expectations of the feasibility study were that VR should offer three-dimensional (3D) simulations that are interactive, high-resolution models of real environments based on best practice Safety Management Plans. It was anticipated that the simulations would allow trainees to experience the consequences of poor decision-making and allow them to learn from their mistakes in a safe and forgiving environment. It was envisaged that such simulators would become an addition to the existing training methods used in the industry.

Jan 1, 2003

The Archean Gossan Hill Group at Golden Grove, Western Australia, hosts two potentially economic volcanogenic massive sulphide deposits. The volcanic-sedimentary succession hosting this mineralisation is composed of a facies association which includes the products of rhyodacitic to,andesitic effusive volcanism, mass-flow sedimentation and concentrated hydrothermal fluid discharge, in a deep subaqueous setting. The Tertiary Kuroko deposits of Japan are widely compared to Archean volcanogenic massive sulphide deposits and a comparison of the facies associations hosting this style of mineralisation, in these two successions separated widely in time, allows a refinement of facies models suitable for exploration in ancient successions. The required deep subaqueous environment for the formation of volcanogenic massive sulphide deposits places constraints on the physical processes that can operate during accumulation of the host stratigraphy. Limitations on the operation of physical processes is reflected by the resultant facies association which can be used to characterize suitable volcanic-sedimentary successions in which volcanogenic massive sulphide mineralisation may be present. The facies association includes: (1) proximal effusive volcanic products - lavas and associated autoclastic breccias (2) distal volcanic products - mass-flow resedimented pyroclastic debris (3) background sedimentation - reworked volcanogenic and terrigenous mass-flow sediments and (4) chemical sediments - exhalites including cherts, sulphides and oxides, with perhaps various carbonates and sulphates. Primary pyroclastic deposits are not expected to be present, other than distal water-lain air-fall deposits, derived from shallow to emergent basin margin explosive volcanic centres, which also provide a source for the resedimented pyroclastic debris.

Jan 1, 1987

By G C. Lukey, J S. J van Deventer

The disposal and subsequent encapsulation of mine tailings in a cost-effective and environmentally secure and responsible manner is one of the principal issues facing any modern mining project. A careful assessment of all options available for the capping and subsequent remediation of tailings is important because it can result in large capital, operating and closure cost-savings. For these reasons, the technology of geopolymerisation is receiving increasing attention for the stabilisation and solidification of waste materials produced from mining operations. The first part of the current study investigates the application of geopolymer technology to the capping of hypersaline mine tailings. It has been found that suitable geopolymeric materials which have satisfactory compressive strength, durability as well as low permeability, can be formed using between 60 - 75 per cent of mine tailings as the main ingredient. It has been established that geopolymeric materials have the ability to suppress dust generation and prevent salt precipitation on the surface of the mine tailings. The slurry-like consistency of geopolymers would promote efficient application procedures through established tailings disposal techniques. This is a possible close-out technique for hypersaline tailings storage facilities such as those commonly found in Western Australia, which meets both regulatory requirements and community expectations. The immobilisation of contaminant metals within geopolymers has been investigated in the second part of the present study. In particular, the leaching characteristics of Cu and Pb from geopolymeric matrices derived from different fly ash sources have been examined. Potential breakdown of each geopolymer containing metal contaminants due to the leaching of Si and Al from the geopolymeric matrix has also been investigated.

Jan 1, 2000

By Berglin IK

Since 1962, ferro alloy production in Australia has been concentrated at Bell Bay, Tasmania with a major expansion occurring in 1976. This concentration was based originally on the perceived requirements of the expanding Australian steel industry, but recent stagnation within this industry has seen Temco become progressively more export oriented.In 1984, approval was given for a $47 million uprating of facilities which will allow for the introduction of the latest technology to ensure high quality, low cost production in a highly competitive export market.

Jan 1, 1985

Expert systems are a product of Artificial Intelligence (AI), a field of long standing, dedicated to the study of problem solving using heuristics, construction of symbolic representations of knowledge about the world, communications proce

Jan 1, 1998

The incidence of colliery disasters has highlighted the need for more centralised and directed coal mining safety research in Queensland, with particular impetus from explosions at Box Flat in 1972, Kianga in 1975 and Moura No 4 in 1986. Inquiries which identified the likely causes recommended measures and, research and two outcomes have been the present Mines Safety Research Advisory Committee and The Safety in Mines Testing and Research Station at Redbank, near Brisbane, dealing with all mining problems, coal and metalliferous. Already, important research into ignition and explosion and other health and safety matters has been accomplished; the Station has become an accredited testing laboratory; and international recognition has been achieved. Now the advisory, testing and research arms are soundly in place to pursue preventive investigations and be ready to provide assistance in any emergencies.

Jan 1, 1991

By Trudinger J. P

Concern for the environment by the public and by mining companies, has led to many recent attempts to revegetate areas disturbed by mining activities. The problem of successfully revegetating disturbed areas and mine wastes is often difficult, even under favourable conditions. Under the severe conditions that prevail in and and semi-arid parts of Australia, such difficulties may be extreme. An approach is described in which field trials are used to investigate factors which adversely affect revegetation and to evaluate optimum methods and treatments..A wide range of methods suitable for use in and situations is described. These include grading and cultivating operations, topdressing with natural soil materials, selection of suitable plant species, mulching and the use of fertilisers and supplementary irrigation. It is concluded that such a programme provides the best approach to this complex and expensive problem.

Jan 1, 1976

By He F, Zhu D

How to monitor and control the support and surrounding strata system on a longwall face effectively is one of the major research problems in ground control. Based on observations on movements of the support and surrounding strata of face No. 2703 of Dongpang colliery, the relationship between the downtime related to support and surrounding strata and other influential factors is analysed systematically in this paper. Monitoring indices and control measures are then determined by taking corresponding downtime as an objective function. When the monitoring method, developed from the above findings, was used on face No. 2703, the downtime due to support and surrounding strata was remarkably reduced, and the face advanced Normally.

Jan 1, 1992

Increasing use has been made of engineer ing geology and hydrogeology in the development of the infrastructure for mining projects. The Geological Survey of the Department of Mines, the Department of Main Roads, the Irrigation and Water Supply Commission and private consulting organisations and mining companies, employ spec- ialist staff to carry out engineering geological and/or hydrogeological investigations. Such in- vestigations have been of assistance in recent mining developments in northern Queensland, in- cluding those in the Cloncurry - Mount lsa, Weipa, Greenvale and northern Borten Basin areas.

Jan 1, 1974

The Mt Newman Beneficiation Plant uses a combination of heavy media deans, heavy medium cyclones and Reichert cones to produce saleable iron ore concentrates from low grade iron ores. The aim of this paper is to discuss score of the changes that have been made to improve the operation of the heavy medium circuits.

Jan 1, 1987

By Larkings RH

The high gas emissions associated with the depth of mining and very high coal extraction at some Australian Collieries have provided a need to investigate the influence of geological and mining conditions on levels of gassiness. The introduction of longwall extraction in particular is associated with complex strata control problems and quick changes in gassiness. To this stage of Australian coal mining, no standard method has been developed to predict the different levels of gassiness associated with the various geological and mining conditions; and the relationship between coal output and total methane make has not been established. For local conditions, with a large number of coal seams lying in close proximity to the working seam, the significant contribution of gas emissions from adjacent strata was expected, especially as strata relaxation occurred during longwall mining. This depends mainly on geological conditions, strata control and coal production. For the deepest of the B.H.P. Collieries in the Newcastle region, the relationship between coal output and total methane make has been investigated by systematic gas balance measurement during longwall extraction. The computer method of iteration was used to approximate the mathematical equation from the initial graphs of coal production versus quantity of methane in the ventilation system for various strata conditions. The angle of caving was established for local geological and mining conditions, for planning and design of the positions of cross measure boreholes.

Jan 1, 1986

By F A. Rosyid

Mineral resources are national assets which must be capitalised for national development. Those assets should be transferred into real economic capital and then into social capital to achieve national/regional prosperity. Successful development in the mining industry will depend on the correctness in determining the role of mining industries for regional development. Using the context of sustainable development, this paper will analyse the concept and process of mining industry development as an accelerator to achieve regional sustainable development, using the mining operations of PT Newmont Nusa Tenggara (PT NNT) in Batuhijau, Sumbawa Barat Regency as a case study. In the premining activity phase, Sumbawa Barat was dependent on the agricultural sector. Agriculture contributed around 40 per cent of the regional gross domestic product (GDP). Meanwhile, in the activity phase, mining became the sector with the biggest contribution to regional economy. From its operation in Batuhijau, PT NNT contributed around 70 per cent of the regional GDP per year since 2001. In year 2000, the GDP had increased 170 per cent from its figure in 1999. However, due to its depleting reserve, PT NNT will finish its activity in Batuhijau by year 2015. Consequently, the Government of Sumbawa Barat Regency must develop other sectors in the post-mining phase to sustain economic development. Based on location quotient (LQ) and input-output analyses, Sumbawa Barat should develop its priority sectors, ie agriculture, trading and hotel, services and construction to achieve sustainability after mining life. Development of these non-mineral sectors is expected to sustain economic growth in the region.

Jan 1, 2008

This paper reviews some of the factors thought to control the formation of supergene gold in the Pacific and its Rim. Discussion of these should lead to reassessment of the economic potential of many areas. In several parts of the world many gold-bearing veins display rich gold values only in the oxidized zone, whereas beneath the present (or ancient) watertable the unaltered vein commonly holds only sub-economic refractory low grade sulphides or arsenides. In the Eastern Highlands of Australia some of the most spectacular concentrations of - gold have been found at shallow depths. For example, Harper (1918) describes the Canton mine in New South Wales which was stoped over a length of 180 metres from the 45 metre level to the surface. The reef yielded gold at 300 g/t in the upper levels, but became gradually poorer at depth. Present geologists of N.S.W. Geol. Survey, G.R. Mcllveen and B.P.J. Stevens, believe that many similar Australian enrichments were formed between the surface and its ancient water table level during the extended period of weathering in the Eocene or pre-Eocene. They concede, however, that further supergene movement of gold may have occurred since the early Tertiary. Large quantities of Mesozoic supergene gold of extreme fineness (Au 99.7%, Cu +òFe 0.3%; Leibius 1885) was found at Mt. Morgan near the Tropic of Capricorn in Queensland. Lower Jurassic sediments cover part of the gossan in a small depression caused by oxidation and collapse of the Main Pipe, thus showing that the supergene gold is pre-Lower Jurassic (Cornelius, 1968). Because the Lower Jurassic landscape around Mt. Morgan was mature with a surface slope of less than 10 (Playford and Cornelius, 1967), erosion would have been very slow. Moreover, once all sulphides had been removed from the ore body the Lower Jurassic environment would have reverted from highly acid to alkaline as it is at present. Accordingly, gold, goethite and 1. Dept. of Geology & Mineralogy, University of Queensland, St. Lucia, Australia,

Jan 1, 1987