Search Documents

By W A. Peppin, D N. Riley, N W. Schulenburg

In June 2008, a joint airborne collection using hyperpspectral systems was tested on a single Twin Otter aircraft. This experiment was designed to incorporate two airborne hyperspectral sensors for geological and environmental projects. Mineral exploration and environmental impact statements are two areas where full spectrum hyperspectral data can document the mineralogy at the surface prior to mining operations. Many previous hyperspectral remote sensing collections were collected on a single aircraft with a single sensor. Mineral mapping using hyperspectral sensors that measure in complimentary regions of the electromagnetic spectrum is cost effective as it allows for the mapping of clays, sulfates, carbonates, feldspars, quartz, garnets and many other minerals. This report describes the experiment using the following two hyperspectral sensors: ProspecTIR, a visible near and shortwave infrared (VNIR-SWIR) sensor with 356 channels and spectral range of 0.4 to 2.5 ¦m, along with a spatially enhanced broadband array spectrograph system (SEBASS), a midwave and longwave infrared (MWIR-LWIR) sensor with 128 channels from 2.5 to 5.3 ¦m and 128 channels from 7.6 to 13.5 ¦m. SpecTIRÆs ProspecTIR system and The Aerospace CorporationÆs Spatially Enhanced Broadband Array Spectrograph System (SEBASS) are pushbroom sensors, have high signal to noise ratios, have similar swath widths and instantaneous fields of view. Examples of data collection experiment will be shown with a focus on mineral/lithologic identification and mapping along with environmental assessment in the western United States. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Milawarma E, Cusack C

The Sapan Dalam coal deposit of Indonesia consists of ten steeply dipping seams with thicknesses varying between 0.1 and 3.5 m and split by shale, clay, silt and sandstone. The area contains four faults dipping about 75¦ with four to 85 m vertical displacements. The complex nature of the deposit coupled with limited 27 exploration drillholes at an average spacing of 200 m made it difficult to create a realistic geological model. A three-dimensional gridded seam model gave a fair representation of the deposit. Attempt to create an optimum pit using the WHITTLE 3D pit optimiser proved unsuccessful since the pit optimiser is restricted to standard regular or fixed blocks. The gridded seam model was converted to a fixed block model prior to the optimum pit design. Smoothing and pit base controlling were also introduced to obtain a smoother pit. A mining scenario produced 3.6 million tonnes of coal, 28.4 million bcm of waste and US$18.1 million revenue.

Jan 1, 1995

By Stevens P

The Isa Mine of Mount Isa Mines Limited currently produces 5.4 million tonnes of copper ore and 3.3 million tonnes of silver, lead and zinc ore annually. Of this, 5.1 million tonnes of copper ore and 2.2 million tonnes of silver-lead-zinc ore is produced by sublevel open stoping. This paper summarises the capabilities, operating practices and problems encountered with current production drilling practices used to drill sublevel open stopes at Mount Isa.

Jan 1, 1982

By Mutmansky J. M, Organiscak J, Qin J, Bhaskar R

The results of a two-year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the analysis results and conclusions of the study are discussed.

Jan 1, 1988

By Holcombe R. J, Dobos S. K, Little T. R

Blue amphibole-bearing rocks in the North D'aguilar Block of southeast Queensland occur either as relict pods and lenses within regionally extensive greenschist facies phyllites and schists or as blocks entrained in serpentinite-matrix melange. Epidote + crossite-bearing varieties predominate and formed under conditions consistent with underplating and high P:T metamorphism in a subduction-related tectonic environment. Neither lawsonite nor jadeite has been observed and metamorphic conditions are estimated at 380-4500C for pressures of 0.5-0.8 GPa. High P:T metamorphism occurred during the earliest stages of deformation and was superimposed upon protoliths of inferred Late Devonian - Early Carboniferous age, including mafic volcanics, tuffs and coarse volcaniclastic breccias as well as pelagic and henipelagic sediments, all of which have undergone varying degrees of over-printing to the greenschist facies. Greenschist facies metamorphism occurred during the second phase of deformation and was associated with the formation of mainly flat-lying or subhorizontal structures; it followed the cessation of subduction and occurred in response to either thermal relaxation during uplift or the imposition of regional heating induced by crustal thickening and/or synkinanatic granite emplacement. Uplift and cooling of the high P:T rocks was completed by 260-265 Ma and may have occurred in response to the same extensional processes which gave rise to the onset of rifting in the adjacent Esk Trough.

Jan 1, 1990

By Townsend MG, Evans RB

In Northland, New Zealand, localised large deposits of halloysite clay have been produced by in-situ alteration of rhyolite volcanics of Pliocene or Pleistocene age, which were erupted through pre- Pliocene sedimentary strata and locally through Pleistocene basalt; and which were subsequently onlapped by further basalt flows. Alteration to clay has been a result of both hydrothermal and of meteoric processes, and decreases in intensity of alteration with increasing depth.The raw material is crushed and fractionated to produce a product of less than 2 micron particle size, which is of exceptional whiteness and brightness. The unique properties of the clays render them highly desirable for specialised ceramic purposes.

Jan 1, 1990

By Glatthar J. W, Lauder D. W, Manlapig E. V, Mackinnon I. R

The Ok Tedi copper orebody consists of porphyry and skarn orebodies. The skarn orebodies, identified by different mineralogies, are the source of high intermittent fluorine levels in the mill concentrates. This paper discusses the results of t

Jan 1, 1998

By D S. Stewart, K W. Keskimaki

The Henderson Mine has been utilising a continuous panel caving method to extract molybdenum ore since starting operation in 1976. In the past three decades since the mine was designed, many changes have taken place in underground technology as well as the general nature of the mining business. The impacts of larger scale underground equipment and automation are significant at Henderson and continue to reshape the nature of the enterprise. During the first years of operation in the 1970s, Henderson required almost 2000 employees to achieve full production, today only about 400 people are required to fully utilise the plantÆs capacity. The most recent change to the facility is the conversion from a rail haulage system to an underground crushing and conveying system that transports ore 25 km to the Henderson mill site. This change has required the introduction of large, rubber tired haulage trucks underground and the mining methods necessary to develop the large openings demanded by the trucks and underground crusher. The development of the underground crusher is also the first step to mining the final bottom horizon of the orebody. Along with this move comes an opportunity to almost triple the effectiveness of the mining effort, through higher draw columns and wider draw bell spacing. This final advancement to a totally trackless mine has positioned Henderson well for safe and efficient operation as it enters the 21st century.

Jan 1, 2000

Strip mining offers the advantages of high productivity from both human and capital resources as well as high rates of production. Experience suggests that it will be advantageous to extend strip mining to the maximum pos- sible depth in order to minimize costs and maximize the recovery of the in situ coal reserves. Highwall and spoilheap stability pose significant problems. Deep working in strip mines is likely to produce a change from methods which are based upon the elevation of material followed by dumping, to methods involving elevation and horizontal transport. There is considerable scope for optimizing the types of machines and minimizing the amount of double handling.

Jan 1, 1975

By Kobayashi M

Particulate chalcopyrite samples (78 ~ 98 mole per cent chalcopyrite, screen size fraction from 710 to 250 µm) were prepared by crushing and sieving lump ore samples from 12 locations in the Mt Isa Mine. Measurements of thennoelectric power (which does not involve the passage of a current) were made using a packed bed that was compressed by loading with a weight and placed in a temperature gradienL Details of the apparatus are described.The effect of particle size was investigated by preparing 12 fractions, with mean particle sizes ranging from 605 to 2.2 µm, from one of the ore samples. Values of thennoelectric power decreased with both increasing particle size and loading pressure; however it remained fairly constant for particle sizes above 80 µm, when loading pressure exceeded 3.3 MPa.Measurements of the chalcopyrite samples gave an average value of -260 JlV/K (-248 ~ -268 µV/K) for nine samples and about -290 µV/K for three samples, showing that these samples were all n-type semi-eonductors.

Jan 1, 1990

By I F. Wood

Planning for flooding and assessment of flood impacts are important requirements for mining projects, as they are also for other types of development. With more intense development and concern from the community, supported by government regulatory requirements, assessment of flood concerns and impacts has become of increasing importance. To ensure that flooding issues are fully understood and results presented in an appropriate format, advanced hydraulic analysis procedures have been developed and are beginning to be applied. These procedures must be rigorous in an engineering context but the results must also be readily understood by the community and government agencies. Advanced two-dimensional hydraulic modelling is becoming accepted as an important means of assessing flooding issues for mining projects. With presentation of results from hydraulic models with Geographic Information Systems (GIS), flood impacts can be analysed rigorously and presented clearly. This paper discusses the application of advanced hydraulic modelling in the planning and impact assessment of a major mining project located on a floodplain where there is extensive inundation. The analysis provides for both input to the planning of the project and for detailed assessment of potential impacts. This case study illustrates some important aspects of the application of hydraulic modelling using a two-dimensional modelling to a critical flood design.

Jan 1, 2003

The key concepts relating to the calculation of recoverable reserves for selective mining in open pit gold operations are discussed. While the general concepts are relevant to a wide range of gold ore bodies, their application is specific to particular ore bodies.The important factors contributing to the recoverable reserves aregeology, mining method, dilution, ore loss, sampling methods and theultimate bench height used in production.The implications of current methods of computing recoverable reservesare reviewed and some alternative approaches to recoverable reservecomputation based on production experience are presented.

Jan 1, 1986

By J Ranford, A Harris, K Laughton

The Angas Zinc Mine (Angas) is a poly-metallic, underground mine in the Adelaide Hills that has been developed through arguably one of the most volatile financial time periods in living memory. From boom times during the commencement of the project, the global financial crisis (GFC) through the stabilisation of the operating period and then a subdued capital market for the period where mine life extension was targeted, the financial environment has always presented a different set of challenges. Indeed even the Underground Operators’ Conferences that have been held across the span of the project allude to these changes: ‘Boom and Beyond’, Launceston (2008); ‘Safe, Innovative and Sustainable’, Canberra (2011) and ‘Managing the Margin’ in Adelaide (2014).Angas gives a rare opportunity to see the entire life-of-mine of a project and its economic performance within a relatively short time frame. Angas, owned and operated by Terramin Australia Ltd (Terramin), will have undergone resource estimation drill out, feasibility study, permitting, commissioning, operating and completion and rehabilitation all within a period of approximately ten years. A number of sensitivities of the project were tested, particularly in the bankable feasibility study (BFS) stage and the aim of this paper is to identify the factors that impacted the operations profitability the most, whether they were identified preproduction or not. The key sensitivities assessed in the BFS were typical of similar studies, including operating costs, metal recoveries, capital costs, zinc prices, lead prices and exchange rates. The manner in which these sensitivities presented themselves in real life were not as anticipated and modelled in the feasibility study and were also heavily impacted by technical challenges.CITATION:Harris, A, Laughton, K and Ranford, J, 2014. Feasibility to mine completion – the real impacts on project economics, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 99–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By R-H Yoon

The thin film pressure balance (TFPB) technique was used to measure the kinetics of thinning of single foam films and disjoining pressures in the presence of sodium dodecyl sulfate (SDS) and electrolyte (NaCl). The results were analysed in view of the Reynolds equation to determine the role of surface forces in film thinning. It was found that film thinning is controlled by surface forces at thicknesses below approximately 200 nm. It was also found that hydrophobic force plays an important role particularly at low SDS and NaCl concentrations. The values of the hydrophobic force constant (K232) estimated from the film thinning experiments were used to predict the disjoining pressure isotherm using the extended DLVO theory, which were found to be in excellent agreement with experiment. The TFPB technique was also used to measure the equilibrium thicknesses (He) of the foam films stabilised by a non-ionic surfactant, n-octanol, in the presence of NaCl. At a given ionic strength, He increased noticeably with increasing octanol concentration at very low concentrations. This observation suggests that hydrophobic force is at its maximum level in the absence of surfactant and decreases with increasing surfactant concentration. The results obtained with the single foam films were used to explain the stability of the three-dimensional foams.

Jan 1, 2005

The genesis of the Bulong Laterite Ni/Co deposit spans some 60 per cent of earth history: from development of the parent rocks in the Archaean to lateritic weathering in the Cainozoic. In a man's term, the discovery and evaluation history of the deposits has also been protracted and, at any given time, the perceived value of the deposits has depended upon the available technology and world markets.

Jan 1, 1996

Scheduling the transformation of in situ coal to run of mine coal and its subsequent beneficiation to a saleable product involves the use of many `parameters' or `adjustment factors'. These include in situ density, moisture adjustments, mining

Jan 1, 1998

The Mobile Miner MM130 (Figure 1) is designed to tunnel or mine in hard rock. It has a 4.1 m diameter cutterhead mounted on a horizontal axis which in turn is perpendicular to the line of the machine. The cutterhead rotates at 15 rpm and is supported on a boom which swings the cutterhead through a horizontal arc.

Jan 1, 1993

Experience in evaluating grade control at operating mines has shown that a number of similar errors re-occur in diverse settings. These can be broadly classed as technical errors, and procedural or grade contra management errors. Examples of typical errors are presented a; generalised case studies. A brief explanation of why the recommender solution worked is also presented for each case.

Jan 1, 1993

Cominco Ltd's Polaris Mine in Canada's High Arctic has been successfully mining zinc ore in permafrost since 1981. Mining methods using frozen backfill have been the key to success. The mine is now producing about 60 per cent of the ore from pillars while maintaining high productivities. Annual ore production is just over one million tonnes providing more than 200 000 tonnes of zinc concentrate each year. Cominco Ltd has adapted management and operating practices to suit the harsh environment and the isolated site, and has shown that a profitable development can be carried out in the tough Arctic conditions, with minimum impact on the environment.

Jan 1, 1993

By Gillies A. D S, Just G. D

The advancement of computer applications in the coal industry is focusing interest on the presentation of washability data by mathematical functions.The normal method of presenting washability data is in the form of five curves, usually filled by eye or by cubic spline functions. It has been shown that coal washability can be characterised by two basic relations: the instantaneous ash vs relative density relationship and the instantaneous yield vs relative density relationship. In a new approach to the mathematical modelling of the instantaneous ash vs relative density relationship, theapplication of the algorithm to a data set from a mine in central Queensland was successful.

Jan 1, 1991