Search Documents

The Ok Tedi open pit mine will have final wall heights in excess of 750m. The behaviour of these excavated slopes will be influenced by the presence of numerous defects. This paper discusses the identification of possible failure mechanisms within the pit walls based on mapped fault and joint data. Results from analyses using these data have formed the basis for the ultimate pit design.

Jan 1, 1994

By Alford R. A

The causes of the loss of heavy mineral from mineral sands wet concentrators were identified through detailed surveys of two such concentrators. It was found that tray and spiral sluices preferentially lost elongated panicles, but panicle size had little effect on loss. Recovery was shown to increase with panicle density. The major influences on the recovery efficiency of individual concentrating devices (stans) were feed rate and feed grade, recovery increasing with decreased feed rate and with increased grade. Uneven distribution of total solids and heavy mineral to individual stans contributed to losses through the corresponding effects in feed tonnage and grade. Computer simulation demonstrated that significant recovery improvements could be obtained by appropriate adjustment of splitters to optimise the characteristics of internal plant flows.

Jan 1, 1991

Cores of pre-Tertiary basement from ten oil exploration wells are related petrologically to the "axial", "marginal" and "shelf" facies of the New Zealand Geosyncline.A NW. Nelson-type basement is inferred beneath peninsular Taranaki and the western continental shelf. The terms Taranaki Basin and Wanganui Basin are re-defined and the terms North Wanganui Basin, South Wanganui Basin, Pipiriki High, Taranaki Fault, and Turakina Fault are proposed. Major faults are interpreted as of mainly transcurrent type and appear to form the western part of a splay at the northern end of the Alpine Fault. Evidence for a major Cook Strait Fault is reviewed.

Jan 1, 1967

By Buisman C. J N, Koch R. O

Soil and groundwater beneath the Budelco zinc production plant at Budel-Dorplein (The Netherlands) are contaminated with metals and sulphate. To avoid contamination of nearby drinking water aquifers in the very distant future, a geohydrological containment system (GCS) and a microbial treatment plant for extracted contaminated groundwater have been developed. As a first step in the design of the system groundwater data from over 150 wells and geological profiles were used to model geohydrological conditions beneath the site. Several configurations of water-extraction wells were deduced from the model. Data gathered during additional fieldwork were then used to improve the model. Finally results that were calculated for the various configurations were used to select an optimal groundwater containment system. Currently some 5000 m3/day groundwater are extracted from a combination of 12 shallow and deep wells. Heavy metals and sulphate have to be removed from the extracted water before it can be discharged into the river system or used as process water. Several water treatment methods have been studied and pilot-tested at the site. The preferred and selected process is based on the activity of sulphate reducing bacteria (SRB) and combines sulphate removal and heavy metal removal in one single step. The anaerobic bacteria reduce the sulphate to sulphide resulting in the precipitation of metal sulphides. A pilot plant gave promising results and a commercial-scale plant has been designed. The proposed design has been tested in a demonstration plant which included all main process units. Test results for all process units are presented. The collected information was then used to optimise the design of the commercial-scale plant. Special attention was paid to automation and safety items. Construction of the plant was finished in May 1992. Start-up, commissioning and operational experience are reported. The concentrations of metals and sulphate in the effluent of the SRB water treatment plant are well within the limits set by the authorities for discharge to public waters.

Jan 1, 1993

By Heyer T, Wasmuth H-D

The concentrator plant of Fahrica Mine, that started production in 1977, was using nine Jones wet high intensity magnetic separators (WHIMS) of the standard type DP 317 with a 1.5 mm gap width for the production of pelletfeed concentrate. These WHIMS units were operating in parallel with a feed rate of 110 t per hour, with about 47 per cent Fe in the feed, and with a maximum of only 0.8 per cent magnetite. The field strength was about 1.2 Tesla. From 1986, the mine has adapted its production facilities to mine and concentrate larger amounts of lowgrade itabintes to maximise the use of the available iron ore reserves. An increase of up to three per cent magnetite in the magnetic separator feed, resulted in a reduction of capacity. This was due to partial clogging of the separation boxes at high field intensities, which were required for the recovery of the very fine hematite. Even by lowering the feed rate and the field intensity the problem could not be resolved. After extensive testwork in a pilot plant, with a Jones separator model DI' 90, the commercial WHIMS plant was modified into a two stage process using the existing nine Jones separators. The gap of the first stage with four machines was increased to a width of 3.5 mm, corresponding to a maximum field intensity of 0.7 Tesla. This first 'medium intensity scalping stage' is followed by a second 'real' high intensity WHIMS step with five machines operating at the original settings with 1.5 mm gap width and 1.0 Testa maximum field intensity. Feed rates of up to 320 tons per hour in the first and up to 240 tons per hour in the second stage could be achieved. The design concept of the concentrator at Fabrica mine is described using the old and new flowsheets. Details of the pilot plant testwork as well as actual performance data of the new plant section are presented.

Jan 1, 1993

By L E. Krause

This paper discusses the considerations for optimum maintenance of critical ore handling infrastructure in order to minimise the cost to the business of maintenance periods. As maintenance periods are a direct interruption to production, time is of the essence and careful management of shutdown periods is essential. The ore pass systems currently in use at Xstrata Copper û Mount Isa Copper Operations are up to 30 years old and have had significant wear over the years. The maintenance of these passes and their brows and chutes in a production situation is a challenge as it can potentially expose personnel to high risk situations in addition to the production interruptions. Some alternatives for mitigating the risk of working in ore passes including plugging and ballooning are described. Criteria are included for selecting a method for the safe entry into a given ore pass. Experience in adapting the method of ore pass plugs and some lessons learnt in the process are also discussed.

Jan 1, 2005

By B Dunstan, F Wirfiyata

PT Newmont Nusa Tenggara (PTNNT) operates the Batu Hijau copper and gold mine and process plant on the island of Sumbawa, Nusa Tenggara (Barat)  NTB, Indonesia. The plant consists of a nominal capacity 120 000 t/d conventional semi-autogenous ball milling crushing (SABC) circuit followed by sulfide flotation to produce a bulk copper concentrate for sale. Process control is effected by a plant wide distributed control system that overlays an extensive integrated programable logic controller (PLC) framework. The system is enhanced by a supervisory expert control system.Since plant commissioning in September 1999, over US$4 million has been expended as part of a systematic continuous improvement approach to optimise plant control performance. Works completed to date include: redesign and upgrade of architecture of the control system to ensure long-term system reliability, security and upgradeability and to provide a suitable platform for advanced control; integration of supervisory and advanced control tools, techniques and instrumentation; and implementation of sound network communication and plant data reporting tools. This paper outlines the evolution of process control and associated systems and tools that contribute to successful operation and ongoing performance optimisation at Batu Hijau.

Jan 1, 2009

By L Richards, R L. Brathwaite, C Mazenga

Underground mining of gold-silver bearing quartz lodes was carried out in the great mines at Martha Hill, Waihi over 70 years from 1882 until 1952. Shafts and stopes reached a total depth of 600 m on 16 levels, with workings extending laterally some 1.6 km, and as new reefs were discovered the workings extended beneath parts of the township. Over their long life the mines produced 1217 tonnes of gold-silver bullion from processing 12.2 million tonnes of mined ore. In the early-1980s drilling proved large reserves of gold and silver ore remaining in stock-work zones between the previously mined lodes. This led to a new era of mining at Waihi with the opening of the Martha Hill open pit in 1988. A series of three sink holes have formed above unfilled stopes of the Royal lode. In 1999 a sudden collapse crater 40 m in diameter occurred near an occupied part of Waihi, placing in danger several houses and a busy street. This crater formed close to a similar crater that occurred in 1961. The 1999 collapse resulted in subsurface investigations and risk assessment studies being commissioned by the local Hauraki District Council. However, a further 50 m diameter collapse crater in December 2001 formed in a residential area, swallowing and wrecking an occupied house, fortunately without injuring its five occupants. Two other houses were perched on the crater rim. The 2001 collapse led to an acceleration of the work being carried out by the Institute of Geological and Nuclear Sciences Ltd. (GNS) to identify the extent of the old underground workings at Waihi. For the risk assessment detailed rock mechanics analyses were made to consider the stability of the underground mine stopes, in terms of the stope back, hangingwall, footwall and crown pillar failure mechanisms, as well as void migration. The collapse crater areas were analysed using using several methods, including analysis to simulate the probability of void migration from unfilled stopes to the surface using the @Risk program. The analyses show that in the cases of the actual collapse craters, the voids have a high probability of migrating to the surface, thus providing a method of testing the void migration modelling. Modelling analysis applied to the remaining stopes of the old underground mines show there are further areas where void migration from unfilled stopes has a high, medium and low probability of reaching the surface as a collapse crater. The locations of these probabilistic hazard zones were outlined using the @Risk modelling and deterministically by using the dimensions of the historical collapses applied along the length of the stopes. Consideration of the æincubation periodÆ (the time interval between the cessation of mining and the occurrence of collapse) and comparisons with mine subsidence histories overseas, indicates that further collapses are likely to occur over the next 50 years. Risk assessment estimates made using property values and occupancy levels within the three hazard zones, were compared with Societal and Individual Risk criteria. Results indicate that safety within the high and medium zones may be unacceptable.

Jan 1, 2003

By S Long, A J Koen, D MacKay

The Mt Wright Underground Mine is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. Following the evolution of the mine plan through a number of stages, the ‘sublevel shrinkage (SLS) with continuous fill’ mining method was implemented in 2010 to extract the Mt Wright orebody. The production front in this mining method is similar to a sublevel cave (SLC) operation; however, backfill is placed into the top of the production zone as opposed to requiring the overlying strata to cave.Continuous fill to replace the void created by extracting the ore was required to manage the potential risks associated with the proximity of infrastructure to the footwall, associated long-term stability and air blast potential due to the limited ‘cavability’ of the material within the cave zone. The available fill material was sourced from a disused waste dump from a previous open pit operation, which introduced further technical and economic risks associated with dilution from ‘no grade’ broken material. Procedures and processes to manage these risks have been incorporated into the operation of the mine.Despite encountering a number of challenges, the SLS method has been in use for approximately three years at Mt Wright and has proven to be viable economically, technically and operationally. This paper will discuss the challenges encountered and what was done to overcome them, the operational and financial performance to date, along with the outcomes of some successful continuous improvement projects that have improved the efficiency of the operation.CITATION:Mackay, D, Long, S and Koen, A J, 2014. Sublevel shrinkage – the Mt Wright story, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 205–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By F R. M Pires, Y Hasui, A Schrank

The iron ores of Alegria mine are composed of itabirites enclosing minor bodies of high-grade ores. The itabirites are classified according to mineralogical composition in five types: martite-rich, goethite-rich, specularite-rich, magnetite-rich and anphibolite-rich ores. The hematites are martite-rich, magnetite-rich, specularite-rich and more rarely, amphibolite-rich. Other classification criteria of the ores are based on the physical properties and the degree of compaction. As such, the itabirites and hematites can be classified as hard, friable and soft types. The mineralogical/textural evolution of the ores is linked to the pressure and temperature conditions that accompanied the tectonic processes in anphibolite facies and the different degrees of subsequent surficial weathering processes. Petrographic and microstructural studies indicate that the magnetite and amphibole bearing itabirites represent the parent rocks that created the other itabirites and that the specularite itabirites and the hard martite types are related to silica dissolution and redeposition in zones of high and low strain. Most of itabirites ores correspond to chert oxide facies banded iron formation, except the goethite and amphibole bearing itabirite that resemble a silicate or oxide-silicate facies with minor carbonate impurities. The great mass and pods of soft martite itabirites are probably shaley oxide facies BIFs with little volcanic contribution. Trace element contents of the AlegriaÆs itabirites show strong dissimilarities with BIFs associated with volcanism (Algoma type), but closely ressemble to the Lake Superior type, with high content in Cr, Co and low V, Ni, Cu and Zn. Although the absolute contents of REE present in the AlegriaÆs itabirites are, in general very low, the pattern when normalised by NASC is similar to the great majority of the Archean and Paleoproterozoic BIFs elsewhere in the world, and characterised by positive Eu anomaly.

Jan 1, 2002

The Central West of New South Wales is emerging as a significant metallogenic province. The development of Northparkes Mines (North Limited) and the Cadia Hill deposit (Newcrest) are establishing NSW as a highly prospective porphyry copper-gold province. Exploration in the area has been further buoyed by the Ridgeway discovery by Newcrest near Cadia. The fact that the Ridgeway prospect was discovered 300 m below surface under Tertiary basalt cover indicates that surface prospecting can no longer be considered alone as an adequate method to find significant new deposits.

Jan 1, 1997

By Dobos SK, Gibson GM, Little TA, Sliwa R

Current studies, and analysis of previouslypublished data, have lead to a re-evaluation of the inclusion of the North D'Aguilar block within the "Gympie Province" in southeast Queensland. The metamorphic rocks are part of a Late Devonian(?)-Early Carboniferous subduction accretionary complex and are unconformably overlain by volcanic and coarse-grained clastic rocks of probable Early or mid-Permian age, as well as by Early to middle Triassic rocks of the Esk Rift. Metamorphic fabrics in the basement rocks include not only those that can be related to convergence, but also younger fabrics that may have developed during Late Carboniferous or Permian uplift and unroofing of the accretionary rocks. A predominance of basic schists, some of which are blue amphibole-bearing, and associated fine-grained pelagic and hemipelagic sediments in the Northern D'Aguilar block contrast with the siliciclastic-dominated sediments of most of the accretionary complexes of the New England Orogen. However the similarity of structural style, and metamorphic and igneous history, with adjacent basement blocks, and with other blocks throughout the New England orogen, suggests that the North D'Aguilar block simply represents deeper, probably underplated, levels of the same subduction complex. Uplift and cooling may have been accomplished by extensional faulting during Permian inception of the Esk rift, which flanks the block on the west.

Jan 1, 1990

In many mining operations, the truck and loader equipment represents the bulk of the invested capital and the majority of the mine operating cost. The profitability of these mines is therefore critically linked to the efficiency of the truck and loader operations. The various factors which affect the productivity of trucks and loaders are analysed by computer simulation, and the results presented in a form allowing assessment of the importance of each factor on overall productivity.

Jan 1, 1983

THOSE who have had occ.asion to sample a mine not infrequently find that it is impossible to take their sample cuts at regular distances apart, owing to the ground being close timbered, a stope having been taken out, or some other cause. When such is the case a tedious calculation becomes necessary in order to obtain an accurate result. A conscientious man will make the tedious calculation, but one who is inclined to be lazy, or who does not recognize the importance of accuracy, or has not the time, may be satisfied with either the arithmetical or weighted arithmetical mean result.There are two main systems of taking samples when the cuts are taken-(l) at equal distances, (2) at unequal distances. When the samples are out at equal distances apart there are three methods of computing the assay value :-1 (a) By Arithmetical Mean. The sum of the values and sum of the widths are each divided by the total number of samples, in order to obtain the value and width respectively, no allowance being made for the relative widths arid values. The result isabsolutely inaccurate, and should never be used under any circumstances.1 (b) By Geometrical Mean. The assay widths ie, feet %, feet oz, inch dwt, &c, are added together and the sum of these is divided by the sum of the widths.

Jan 1, 1911

By Muto S, Okada S

At Tamano Smelter, part of the furnace settler is electrically heated by electrodes placed internally. This practice provides good control of the settler conditions. The authors have been investigating improvements in furnace operations, especially to decrease the copper content in the slag discarded from the settler. The important operational points on the control of magnetite in liquid matte and slag are discussed on the basis of the thermodynamic calculation method developed by Prof. S. Goto. The behaviour of magnetite in the practical furnace has been studied by using a torsion magnetometer and a solid electrolyte oxygen-sensing cell.

Jan 1, 1980

By Rose CW

Typical rehabilitation programmes for spoil piles and waste dumps in open cut coal mines involve the spreading of topsoil to assist vegetation growth. In the early years of rehabilitation before a protective vegetation cover has been established, this topsoil is susceptible to erosion during rainfall events. Since the long term success of rehabil- itation procedures is sensitive to adequate topsoil maintenance and since, on many mine sites, topsoil is a scarce resource, erosion losses of topsoil (particularly once fert- ilised) can severely restrict rehabilitation Measures.

Jan 1, 1983

The Loy Yang Overburden System initially consists of a 60 000 tonne/day Bucket Wheel Excavator (BWE) (No. 14), a 2 m wide Conveyor System and a Travelling Stacker (No. TS4). The paper discusses details of the plant and the influence the soft clay overburden has on the design of the plant, to handle the dif- ficult Latrobe Valley overburden.

Jan 1, 1982

The Central Extended Orebody is located within the Cracow Goldfield approximately 360 km northwest of Brisbane and approximately 220 km west of Bundaberg. It is an epithermal gold deposit hosted by the Late Carboniferous to Early Permian Camboon Andesite. The lode was mined by open cut methods and produced 170 458 tonnes of ore at 5.62 g/t gold.The geology of the rit is relatively simple, comprising two rock types, trachyandesite and rhyolite which have been sub-divided into several units. The trachyandesite is sub-divided into three rock types: brecciated trachyandesite which is the most widespread, hydraulically fractured trachyandesite hosts the mineralisation and the third sub-unit is chloritised hydraulically fractured trachyandesite and has no associated mineralisation. The mineralisation is confined to quartz veins in hydraulically fractured trachyandesite. Several phases of brecciation and subsequent quartz and quartz/adularia vein injection are evident although not all phases are mineralised. Two rhyolite dykes intrude the trachyandesite one is monolithic, the other is sub-divided into hydraulically fractured rhyolite (barren), silicified rhyolite and auto-brecciated rhyolite.

Jan 1, 1993

By Fazakerley VW

The Murrin Murrin deposit is located about 210 km NNE of Kalgoorlie and 50 km E of Leonora in the North Eastern Goldfields region of Western Australia at latitude 28¦ 50'S. longitude 121¦ 54'E on the Laverton (SH 51-2) 1:250 000 map sheet. The tenements are held by Anaconda Nickel NL. Geological investigations between 1994 and 1996 resulted in resource calculations being completed for the ten lateritic nickel cobalt deposits shown in Figure 1. At a 0.8 per cent nickel cut-off the resources at May 1996 for the nine deposits are 116.8 Mt at 1.10 per cent nickel and 0.082 per cent cobalt. The nickel-cobalt mineralisation is contained in a laterite profile developed over Archaean serpentinised peridotites. A bankable feasibility study has been completed and the project is scheduled to be in production by the beginning of 1998.

Jan 1, 1996

In early-1989, subsidence due to voids at the top of previously filled stopes and stopes awaiting filling,began to threaten the 15 level fill conveyor horizon. This together with the need to maintain production targets meant that a method was required to significantly increase fill placement.Alternative methods of placing dry fill underground were investigated. One option was to drill 200 mm boreholes from surface directly into stopes 600 - 800 metres underground. A drilling program was successfully undertaken, and resulted in the placement of more than 800 000 tonnes of dry aggregate fill via four boreholes.This paper details the drilling program undertaken and discusses the difficulties encountered, the fill placement system and the project costs.

Jan 1, 1992