Search Documents

By M J. Saynor, W D. Erskine an, D R. Moliere

The Jabiluka uranium mine was constructed in the Ngarradj catchment, a right bank tributary of Magela Creek in the Northern Territory. The Jabiluka Mineral Lease is adjacent to Kakadu National Park, near an area listed as Wetlands of International Importance under the Ramsar Convention and recognised under the World Heritage Convention. In the late dry season of 1998 and prior to the 1998 - 1999 wet season, a stream-monitoring program was implemented in the Ngarradj catchment to collect baseline data on sediment transport within the catchment to assess and proactively manage associated impacts caused by mining at Jabiluka. Stream suspended mud concentration, stream discharge and rainfall data were collected for four wet seasons (1998 - 2002) giving an almost continuous data set. The stream system has high natural variability dependent on rainfall intensity and subsequent discharge and pre-wet season fire distribution and intensity. In general, mud concentration is elevated at the commencement of the wet season until about February. This is caused by first-flush removal of surface material detached during the dry season by agents such as bioturbation (including anthropogenic activity), wind erosion and surface desiccation. Water quality trigger values downstream of the mine were derived using upstream percentiles and the before-after-control-impact, paired site design. Both analyses showed no observable impact from mine construction in 1998 or during the study period. However, the impacts of dry season fires could be clearly detected. The data set provides good baseline information for future assessment at Jabiluka and demonstrates the need to view measured parameter values on a catchment-wide basis with knowledge of rainfall, discharge and fire distribution.

Jan 1, 2004

By M Hudyma

Open stope mining is the most common mining method employed in underground, hard rock mines in Canada. It is characterised by relatively small, single lift stopes (20 000 to 100 000 tonnes), and fast stope turnaround times. Host wall rock mass conditions, which are typically poor to fair, are the controlling parameter in stope dimensioning. Rock mass stability is maintained by designing all stope surfaces at a stable dimension, and through extensive use of cablebolting for stope backs and frequently stope hanging walls. Dilution control is a high priority. The typically small, high-grade, deep and irregularly shaped orebodies are incrementally developed, usually in a bottom to top direction. In many cases, high stress is encountered due to the depth of the orebodies. Overstressing of pillars and hanging pillars are avoided through the use of pillarless or early pillar recovery mine sequencing strategies. Stopes are invariably filled, and in higher grade and wider orebodies, cemented fill is commonly used. This paper generalises many of the similarities found in Canadian open stope mines.

Jan 1, 2000

By M D. Raine, J K. Bartlett, S C. Dominy

The Bendigo Goldfield is located in the state of Victoria, Australia, and is one of a number of fields that make up the Central Victorian Goldfield. Since 1993, Bendigo Mining NL has been carrying out an extensive re-evaluation of the goldfield and is currently well advanced in developing an underground mine. The sediment-hosted auriferous quartz reefs are structurally complex and closely associated with anticlinal axes and reverse faulting. The gold within the quartz reefs is characterised by both its coarse nature (100 up to >5000 ¦m) and its erratic distribution; as a result, the Bendigo Goldfield is classed as an extreme nugget effect system. This characteristic ensures that the Bendigo mineralisation is very challenging to sample and evaluate. In this case, diamond drilling is a good measure of structure and geological continuity, but a poor measure of grade and grade distribution. Drilling, combined with on-reef development, bulk sampling and detailed geological studies are required for resource evaluation. For grade control a balance has to be sought between sample representativness, cost, turn around time and practicality. Extreme nugget effect deposits like Bendigo, require the use of bulk samples in order to be representative. However, the cost and turn around time is significant. As a result, a micro-bulk sampling system has been introduced that attempts to overcome these problems by providing a fast, practical method that can define ore from waste. Bulk sampling and on-vein development are still necessary for resource and reserve estimation.

Jan 1, 2003

By G Solly, S Parsons, P Leevers, S Ni

Hematite ore has been mined in the Southern Middleback Ranges as blast furnace feed for the steelworks at Whyalla, by what was then BHP, since 1991. With the floating of BHP Integrated Steel as OneSteel in 2001 and the subsequent loss of key mining personnel, breakdowns in grade control methods and procedures occurred. These were compounded by changes in orebody characteristics and grade distribution leading to poor reserve recovery and poor grade control, both which resulted in loss of control of ore specification and severe deviation from the mining schedule. As a result, a total review of grade control, mining method and scheduling procedures was undertaken as well as a review of contractor quality assurance. It was found that sampling methods were poor and unrepresentative, grade control blocking processes were outdated and did not reflect the geology of the deposit, the ore mining method was outdated and did not respect the geometry of the orebody, reconciliation methods were being completed globally and were not reflective of individual areas of the deposit, and that deviations from the mine plan were occurring due to access to high-grade areas outside the schedule in order to bring stockpiles back on grade. Based on these findings, updated sample splitter systems were fitted to drill hole rigs, double bench sampling was implemented (2 + 4 m samples as opposed to 1 + 8 m sample) and a three-dimensional cellular grade control system introduced to better reflect the geology and orientation of the deposit. At the same time ore mining was changed from front end loaders mining on 8 m benches to excavator mining on three lifts on 8 m benches; this aided selectivity and respected the geometry of the orebodies aiding cleaner recovery. Reconciliation is now completed on a blast-by-blast basis, which allows for quick and easy identification of poorly performing areas of the resource model that can then be incorporated back into resource model updates. Regular daily and weekly meetings are also held with emphasis on the mining schedule to ensure no deviation from the schedule in the long term. These improvements have resulted in a lift in reserve recovery both globally and locally associated at the same time with improvement in grade.

Jan 1, 2005

By Gibson G, Jaques L

The Broken Hill Exploration Initiative (BHEI) is a collaborative venture between the Australian Geological Survey Organisation (AGSO), Mines and Energy South Australia (MESA) and the New South Wales Department of Mineral Resources (NSWDMR) to provide a new generation of geoscientific information to promote and enhance the exploration for, and discovery of, new deposits in the Broken Hill region. The area under investigation (Figure 1) exceeds 150 000 square kilometres on either side of the NSW-SA border and is centred on the city of Broken Hill. N.T. I I OL n. WA 8A I Maw. AC,7 !ii oFCU vlc~ ~T. Fia I - Nlap showing the 150 000 square kilometre regwa,. i.i lcr investigation by the Broken HiII Exploration Initiauvr highlighted on the map of Australia. A major impediment to the exploration for, and to the understanding of, the genesis of the world-class Broken Hill Pb-Ag-Zn deposit is the structural and metamorphic complexit\ of the region. Important objectives of the BHEI are therefore: I. the definition of the three-dimensional structure of the province, 2. the deformation history, and 3. the stratigraphic and age relationships of the rock units. Early discussions between the BHEI partners and industry scientists revealed that new geophysical surveys would be a key requirement to help advance the understanding of the province, especially a contiguous high resolution airborne geophysical dataset covering both outcrop and areas of shallow surficial cover. The purpose of this paper is to draw attention to the new high resolution airborne geophysical data and to discuss their interpretation and potential for enhancing the knowledge of the Willyama Supergroup geology.

Jan 1, 1997

One of the features of modern life has been the increasing speed of change. We see this in many facets of activity, but in few areas more clearly than in the financial sector. The speed of communication and the advent of screen trading have made world markets one.We have titled this presentation "Cycles". It has been the conventional wisdom that Economies, Metal Prices, Equity Markets, etc. move in cycles. The objective of our presentation is to examine these cycles, to comment on the interrelationships, and to postulate where we are in The Current Cycle". We will draw conclusions as to where one should direct effort in the Mineral Scene over the next decade or so.Throughout this discussion we will use various terms to describe Time. The "Short Term" is typically meant to refer to the next six months: the "Medium Term" is one to two years; and the "Long Term" is the three to five year horizon.

Jan 1, 1990

The exploration and mining risks are investigated and compared to the risks of smelting, secondary processing and other normal industrial activities. This study concentrates on the risk before, or at the investment decision. Internal and external risks are distinguished. Internal risks are the risks inherent in every engineering design and common to all projects. The main external risks are the financial risk, changes in prices, location problems and geological factors. Financial risks concern every capital-intensive and export-oriented project and cannot be considered as typical mining risks. Changes in prices, i.e. the market risk, concern every industry using raw materials, but the market risk is especially accentuated in the mining industry. Problems of location and infrastructure are normally more significant in mining than in other projects, and geological risks are unique to mining. All these risks associated with mining projects combine to form a risk at least twice as high as that for other normal industrial activities. Within the range of profitability of mines, which on average is the same as in the manufacturing industry, only a few highly profitable mines exist. These few mines are the sole reward for the high risks taken.

Jan 1, 1986

By Wright J. K

In recent years the production of steel from directly reduced iron ore pellets has ex- panded rapidly. However continued growth will depend on an adequate supply of suitable raw materials for the various commercial gaseous and solid reductant processes now in operation. Al- though at present Australia does not produce pellets primarily for direct reduction, there is an increasing awareness of Australia's potential role as a supplier of high grade ores for export and/or domestic use. The properties and quality requirements of iron ore pellets made specifically for directre- duction (DR) are reviewed and the laboratory techniques and test methods used at the CSIRO Division of Process Technology for the evaluat- ion of potential DR feedstocks are described. At the present time most of the evaluation tests for DR pellets are extensions of those de- signed for existing blast furnace (BF) burdens. In the case of some physical parameters such as cold compression strength, abrasion index and cold strength after reduction this extension is quite satisfactory. In the measurement of para- meters such as reducibility, swelling and stick- ing tendency, however, it is necessary to deve- lop meaningful standardized tests so that ores and pellets can be ranked for DR performance. To do this, data from the laboratory tests and from operating plants must be correlated.

Jan 1, 1980

By Krouse RH, Aleinikoff JN, Nokleberg WJ, Church SE, Newkirk SR

A belt of volcanogenic massive sulfide (VMS) deposits and occurrences extends for over 150 km along the southern margin of the Yukon-Tanana terrane in the eastern Alaska Range. The VMS bodies occur mainly in the Jarvis Creek Glacier subterrane (JCGS), one of the highest structural/ stratigraphic levels of the Yukon-Tanana terrane. The JCGS consists of a VMS--bearing metavolcanic rock member and a metasedimentary rock member. The VMS deposits and enclosing rocks exhibit two periods of regional metamorphism.From northwest to southeast, the major VMS districts are the Bonnifield, Hayes Glacier, McGinnis Glacier, and Delta districts. The Bonnifield, Hayes and McGinnis Glacier district sulfide bodies consist of pyrrhotite and lesser amounts of pyrite, chalcopyrite, with or without arsenopyrite, sphalerite and galena. The larger, 800 km Delta district deposits and occurrences contain variable amounts of pyrite and pyrrhotite and lesser amounts of primarily chalcopyrite, galena, sphalerite, and arsenopyrite.The sulfide accumulations are interpreted as Kuroko-like deposits that formed along the submarine volcanic part of a Devonian, continental-margin igneous arc. U-Pb isotopic data from zircons from the metavolcanic rocks indicate an age of about 370 Ma (Devonian). 207Pb/204Pb ratios for sulfides from the districts are similar and indicate lead was in part derived from first cycle sediments eroded largely from Precambrian crystalline rocks. 207Pb/204Pb ratios from feldspars in Devonian metavolcanic rocks are similar to those in sulfides, and indicate incorporation of radiogenic Precambrian lead into the Devonian magmas. A Precambrian crystalline source for quartz in metasedimentary rocks is indicated by 2.3 Ga old zircons. Common-lead isotope studies of igneous phenocrysts in metaigneous rocks and sulfides in volcanogenic massive sulfide deposits indicate a unique isotopic signature. The data permit an exotic origin of the Yukon-Tanana terrane with respect to North America.

Jan 1, 1990

A new gold cyanidation assay technique has been proven for a range of ores, where it has demonstrated benefits of being: ò Accurate (reduces the typical range of assay scatter almost three-fold, and avoids common fire assay interferences). ò Fast (under one hour, providing a quantum shift in space requirement and equipment utilisation each bottle roll can provide over 15 determinations per day). ò Simple (suitable for field application, no high skill or experience requirements). ò Profitable (reduced drilling, drilling time, ore misclassification and/or double handling after mining). ò Cheap (far lower cost than Fire or Aqua Regia Assays, ie LeachWELLTM costs around 10ó for a 20 g sample at 50 per cent solids, proportionately greater for larger samples eg $1 for 200 g samples which address most nugget effect problems). ò Relevant (distinguishes economic. ie cyanide-extractable gold, the only unequivocal value to use for true resource definition, mine planning and grade control). ò Robust (rough bucket chemistry of samplers does not seriously affect results). A new development is the provision of LeachWELLTM CAS, a solution, which also contains optimum cyanide and stabiliser concentrations; and offers greater: ò Safety (the dilute cyanide solutions are stabilised to avoid generating toxic HCN vapours; and present no cyanide dust or flying chips to deal with). ò Ease (a single squirt dispenses precise quantities of the entire reagent suite, avoiding multiple weighings). ò Reduction in total reagent costs. An inter-laboratory comparison on nine ore types, using two assay techniques (Fire Assay and Aqua Regia) involving 45 laboratories, has demonstrated that LeachWELLTM 60X assays for the samples tested, were equally or more reliable than typical Fire or Aqua Regia Assays. There is particularly great benefit in applying LeachWELLTM 60X assays to richer ores in comparison to Aqua Regia assays, which appear to be prone to very significant underassaying depending on individual analyst skills, and which often suffer greater nugget effects. The major impacts for heap leaching are that: ò Using the LeachWELLTM assay technique for grade control, ore of marginal grade is not accidentally discarded to waste or visa versa due to the scatter of assay data inherent in typical small charge (25 g) fire assays. ò LeachWELLTM assays very importantly report only that gold which will be recoverable in the heap, viz that which is liberated - an important factor where the coarse crush often leaves ten per cent of gold unliberated. These impacts are of particular importance for many ores (ie most of those recovered from open pit operations and at the margins of rich ore subject to slurry processing) subjected to heap leaching as the oxide zones often present major problems of nugget effects as well as mineralisation that cannot be accurately assigned through interpretation of clear structural controls.

Jan 1, 1994

A shift in the present day oil exploration scenario from West Coast can be foreseen keeping in mind peak of exploration in Cambay Basin and fast pace of development in Bombay High and its associated fields by the end of this century. Shifts in exploration from structural traps to stratigraphic traps, techno- logical development to drill in deep waters, improving economic situation for oil ventures and proven oil and gas potential of East Coast basins suggest that Indian oil explorat- ion scene will be at its peak along east coast during early 21st century. Hydrocarbon shows in Poonch and Jawalamukhi in Punjab Basin, improvements in drilling to greater depths, better seismic data aquisition, good source rock potential of Subathus and its equivalents and large geologi- cally mapped structures will reopen new avenues for explorationists. Not much exploration effort has been put up so far in Ganga Basin. Keeping in mind size of the basin, sedimentary thickness involved, presence of algal matter deposited in shallow marine environment & higher hydrocarbon indications warrant active exploration. Gondwanas in India having such a large sedimentary area can not be ignored keeping in view generation and production from the non marine sediments of Kenya, Chad, Sudan, Gadon and China. Gondwanas become all the more important in view of gas production from their equivalents-Karoos in Ethiopia and South Africa. In all, above mentioned changes can be predicted in Indian oil exploration scenario during 21st century.

Jan 1, 1986

Mathematical modelling of continuous rotary vacuum filtration has been limited by the wide range of variables and the absence of connecting equations linking the variables. The filter type and size, mechanical design and predicted performance are generally determined by laboratory leaf tests on representative samples of slurry, or plant samples from an operating filter. A model has been developed which includes the major process variables such as slurry feed rate and concentration, cake thickness, wash water and air flow rates, to predict the filter production throughput, cake moisture and residual solubles. Where possible the model incorporates well established equations relating form filtration, washing and drying rates of the filter cake. Where an equation has not been formulated, standard curve fitting programs have been used to establish an algorithm. The theoretical equations and the derived algorithms are defined in the text. A major feature of the model is that operators, metallurgists, process, mechanical and instrumentation engineers become more aware of the interaction of process variables, the principles of the equipment design and its limitations when operating at peak performance. The model has specific application in the alumina industry where a high moisture content of the filter cake can increase chemical losses and energy costs, and in the coal industry where overseas companies are insisting on lower export coal moistures.

Jan 1, 1989

By Regan R

Appin Colliery mines the Bulli Seam with a gas composition of 98.5% methane and 1.5% carbon dioxide. Relaxation of the strata generally occurs to below the base of the Wongawilli Seam, some 40 m below the Bulli Seam, and approxim- ately 125 m above the Bulli Seam, for longwall face widths of 135 m or more. Previous exper- ience showed that when longwall faces were mined for a distance approximately equal to the face width, the mine ventilation could not provide sufficient dilution due to methane emissions from the underlying measures. Postdraining downholes were drilled to intersect the Wongawilli Seam below the operat- ng longwall. These holes were connected to an underground to surface gas range and various suction levels were applied to improve gas drainage. The resulting gas flow rates and purity from all the downholes were regularly monitored and peak flows in some holes exceeded 160 1/sec. The surface plant drained almost 20 million m3 of gas for the period July 1981 to January 1982 at an average methane purity of approximately 70%. Distinct patterns emerged for different downholes from curves illustrat- ing their variations in flow rate with distance subsequent to passage of the longwall face. The difference between free flow characteristics and those obtained with the application of

Jan 1, 1982

By J Leppinen, B Johanson, R Kalapudas, G McMahon

The Suurikuusikko gold deposit was discovered in 1987 in western Finnish Lapland, 54 km NNE from the town centre of KittilS in the volcanic belt of Central Lapland. It is hosted by tholeiitic basalts in a graphite-bearing albitite breccia. The ore is located in subvertical shear zones characterised by strong albitisation, carbonatisation and sulfidisation. The ore minerals consist of arsenopyrite, pyrite, chalcopyrite, sphalerite, tetrahedrite, bournonite and rutile. Small amounts of pyrrhotite, gersdorffite, jamesonite, bornite, gudmundite, tetrahedrite, stibnite, kermesite, berthierite and native Sb are also present. Gold occurs as invisible and as 1 - 2 ¦m size inclusions in arsenopyrite and pyrite, on their grain boundaries and in fractures. The average amount of gold leached by cyanide is 2.93 per cent. The æinvisibleÆ gold contents were studied in pyrite and arsenopyrite by electron microprobe analysis (EPMA) and secondary ion mass spectrometry (SIMS) at CANMET/ MTL. Gold element distribution images show zoned patterns both in pyrite and arsenopyrite. SIMS analyses range from 343 to 55 ppm Au in arsenopyrite and from 217 ppm down to 0.32 ppm (detection limit 478 ppb) Au in pyrite. EPMA results range from 939 to below the detection limit 24 ppm Au in arsenopyrite and from 267 ppm to below 22 ppm Au in pyrite. Recovery of the refractory gold ore was studied using grinding, flotation, bio-oxidation and cyanidation tests. A sulfide bulk concentrate containing 40 ppm Au was obtained by flotation at 90 per cent recovery (As content 5.5 per cent, S content 22 per cent, and mass recovery 15 per cent). The grinding fineness in flotation was P80 -100 to 120 ¦m. At the original fineness the cyanidation recovery from the concentrate was lower than ten per cent, after ultra-fine grinding P80 -10 to 2 ¦m the Au recovery was less than 17 per cent. After bio- oxidation, Au recovery of 95 per cent was obtained in carbon-in-leach (CIL). The bio-oxidation time was two weeks in laboratory test, but after regrinding the oxidation rate was faster and recovery of Au higher. However, the selected method for the mining to be started in summer 2008 is open pit mining and mineral processing methods sulfide flotation and pressure oxidation in an autoclave. The ore reserves were estimated 31 December 2007 as: Probable 18.2 Mt with 5.1 g/t Au, Indicated 5.4 Mt with 3.0 g/t Au and Inferred 10.8 Mt with 3.4 g/t Au. The production capacity will be 3000 t/day.

Jan 1, 2008

By Whittaker B. N, Reddish D. J

This paper presents the physical modelling results of subsurface fracture development associated with Iongwall mining operations and an application of image processing techniques to interpretion of the results. Physical modelling results haióbeen obtained by employing a large sand and plaster model loaded purely by gravity as a means of fracturing the subsurface strata above the longwall excavation. The results have shown fracture development and crack propagation as a longwall face advances and demonstrated that the strength of stratified rocks, the presence and position of a weak band-, and the extraction thickness, have significant effects upon the overall fracture patterns above the excavation. Binary images of fracture patterns were scanned from the black and white photographs of the tested models using an image analyser coupled to a video camels. These images were manipulated by a custom written C program which allows the images to be processed in both vertical and horizontal direction. The images were filtered to quantitatively differentiate between vertical and horizontal fracture intensities. The vertical fracture intensity is particularly important as vertical fractures are considered to provide the main avenues for surface and subsurface water inflow into the excavation. The use of the image analysis techniques has shown a promising improvement in image enhancement and in model results interpretation in a quantitative manner. The numerical nature of the image analysis results will allow further statistical comparison with other modelling techniques to be undertaken and significantly increase the scope for use of the modelling technique results.

Jan 1, 1992

By B Chappell

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to be placed in a tailings dam. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electroosmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

Aspiring to be excellent makes you a good leader as it shows a capability for strategic thought, defining and implementing a vision, making a job easier, more efficient and effective. Every great business leader can generate additional revenue or cost savings for their company. Becoming excellent requires the desire and action to follow it through. There are many established methods of excellence: benchmarking, target setting, supply chain and market analysis, employee suggestions and knowledge sharing forums. In BHP Billiton, practices benchmarking is a key tool in generating improvements for functional areas such as processing, mine operations and mine planning. Practices Benchmarking involves organisational and technical questions that allow the site to self-assess their maturity and generate a prioritised improvement path. Not only does it benchmark and identify gaps, but the approach also facilitates networking, education and team building. For new leaders it is important to remember that you are not alone. Chances are your problem has been solved before. Networks û internal, external, formal and informal can get you started and often save you time and effort. Any leader can achieve success in excellence through a proper process of problem formulation, data and analysis. Again, using key players can make the process more effective. It is important to remember that the people side of the solution is the key to success and that monitoring will ensure the solution will work. In the words of BHP BillitionÆs CEO, Chip Goodyear: Excellence is a mind set. ItÆs something that comes when people get rewarded forthinking outside the box and applying their skill and knowledge. It happens, not in$50 million chunks, but in hundred thousand and million and $2 million chunks.When you get 35 000 people thinking that way, then youÆve really got somethinggoing.

Jan 1, 2005

The Mount Whaleback iron ore deposit at Newman, Western Australia comprises the largest known continuous iron ore deposit in Australia, originally with a Measured Resource in excess of 1700 Mt of hematite ore. The deposit occurs within the Hamersley Province which forms part of the Pilbara Block in the NW of Western Australia (Figure 1). The Mount Whaleback iron ore deposit, together with a number of discrete iron ore bearing satellite orebodies in the Newman district, contributes to the Newman Lump and Fines products. Extensive quality control systems are utilised from mining to shipping to ensure that each product meets a narrow geochemical target grade range.

Jan 1, 1997

By Rashchenko AF, Voiloshnikov GI, Elshin VV, Khomutov VV

The sorption method for the precious metals recovery fromsolutions and pulps are a perspective trend of modernhydrometallurgy. Russian gold mining industry uses thesemethods, anion-exchange resins being applied as sorbents. Theanion exchange resins allow effective recovery of preciousmetals, however, they have several drawbacks as compared withactivated carbons: high cost of sorbents; difficulties arisingduring treatment of pulps with complex ion composition;necessity of using titanic equipment and thiourea for gold elutionfrom loaded anion-exchange resin and its regeneration.

Jan 1, 1993

By R H. Yoon, M Gupta, A Noble, K Huang

Froth flotation is the most commonly used separation technology in the mineral industries. Given the complexity of the pulp and froth phases as well as the multitude of operational parameters that influence flotation performance, purely fundamental models with strong predictive capacity are limited. As a result, accurately modelling modifications to an existing flotation circuit are challenging, particularly when using empirically-derived models from a different operating configuration. Despite these complexities, a recent publication by the authors (Huang et al, 2022) has shown that flotation rates can be accurately predicted from a first-principles model that incorporates hydrodynamic parameters (eg pulp density, superficial gas velocity, feed flow rates etc), surface chemistry parameters (eg contact angle, zeta potentials and surface tension), and size-by-class liberation data. Circuit simulations using this model were shown to be effective in predicting experimental graderecovery curves from the size-by-class mineral liberation matrix. Since the model is derived from fundamental characteristics of the flotation system, it can be used to simulate alternative circuit configurations with varying degrees of recycle. Conventional flotation circuits are operated in a closed-circuit configuration by routing the cleaner scavenger tails (CST) back to the rougher feed to provide an additional opportunity to recover the slow-floating particles. This widely-used flotation strategy has been under constant debate, and several researchers have provided evidence that open circuit configurations provide higher separation and better circuit control (Konigsman, 1985; Bulatovic et al, 1998; Thompson, 2016). Recently, Finch and Tan (2021), used linear circuit analysis to show that open circuit configurations have a fundamental advantage when stage recoveries are high. Given the limitations of these prior studies, the objective of the current work is to further evaluate the merits of the open circuit configuration through a detailed circuit analysis and simulation study incorporating the first principles model described above.

Aug 24, 2022