Search Documents

Design of underground extraction layouts to protect surface improvements is an important area of subsidence research in the Coal Mining Engineering Branch of the Department of Mineral Resources, New South Wales, Australia. Some conventional partial extraction layout are important with reference to coal recovery and surface subsidence. The analysis ofsubsidence data collected from field surveys over longwall panels in the Southern Coalfield of New South Wales allows assessment of the effect of pillars left unmined between the longwall panels in reducing surface subsidence. The availability ofa wide variety of layouts with ranging degrees of surface movements affords considerable flexibility in designing layouts to suit a particular situation.Total extraction of coal should be the aim as far as possible. Partial extraction layouts should only be considered when surface subsidence movements caused by total extraction are not acceptable to the surface improvements.

Jan 1, 1985

By P Voigt, B Lumsden, P Lines, I Gurnett

Plant tests of magnetic conditioning have shown increased flotation recovery of paramagnetic sulfide minerals (chalcopyrite, sphalerite and pentlandite) in the -38 ¦m size fraction within rougher and cleaner flotation circuits. A statistical plant test was undertaken in the Mount Isa zinc flotation circuit where magnetic conditioning was tested simultaneously in both the rougher circuit and the cleaner retreat circuit (cleaner scavenger). This test resulted in a normalised increase of 1.60 per cent in the rougher circuit zinc recovery and simultaneously a normalised increase of 4.60 per cent in the cleaner retreat circuit zinc recovery - to a very high level of statistical confidence. Interestingly, in a novel approach, it was possible to verify the plant test results in two ways. Firstly, detailed MLA analysis of the tails confirmed the statistical plant test results and showed that the greatest effect of magnetic conditioning was on the sphalerite in the C3 - C6 size fraction, where there was a reduction of around 15 per cent in zinc in tails. Moreover, there was a reduction of around 15 per cent in liberated sphalerite across all -38 ¦m size fractions, but only a seven per cent reduction in non-liberated sphalerite in the tails. Secondly, plant modelling showed that increasing the rougher zinc recovery would cause an increase in zinc feed grade to the cleaner retreat circuit. The increase in the zinc feed grade to the cleaner retreat circuit with magnetic conditioning was demonstrated to a very high level of statistical confidence.CITATION:Gurnett, I, Voigt, P, Lumsden, B and Lines, P, 2012. Magnetic conditioning of sphalerite at XstrataÆs Mount Isa Zinc Operations, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 233-240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By D Pepper

Despite the limited literature regarding the pressure filtration of mine tailings (compared to the large number of papers published each year on paste thickening of tailings) the number of mines dry stacking filtered tailings is approximately equal to the number of mines storing tailings in paste form. Main drivers for filtering tailings are: water recovery, future rehabilitation costs for tailings storage area and permitting requirements. In arid climates, the cost and scarcity of water justify the capital and operating costs associated with pressure filters. Further justification for filtered tailings is the potential for progressive reclamation of the dry stack, which can proceed earlier and faster than the reclamation of a tailings dam.Filtered tailings must be transported to the storage area by trucks or conveyors. For dry stacking, 70 - 80 per cent solids content (by mass) is typically acceptable, however the primary goal is to provide a filter cake that is consolidated and dry enough to prevent bridging and build-up on the materials handling equipment. It has been observed that high average solids contents (~70 per cent) can be achieved while the centre of the filter cakes is still wet and sticky, presenting challenges for the transportation of the solids. Appropriate controls must be in place to ensure consistently easy to handle solids are discharged from the filter.FLSmidth has installed two fine coal tailings dewatering systems in the United States. One of these systems incorporates a Deep Cone Thickener« upstream of the filter press to minimise the amount of water that must be filtered, while the other tailings filter press is fed by a high rate thickener. The operation and performance of these filters is discussed and compared to the lab testing used to size the full-scale equipment.CITATION:Pepper, D, 2012. Operation of filter presses for tailings dewatering, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 241-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Felice J. J

The assessment of the face velocity of blasts is important in the analysis and subsequent improvement of blast performance. POWERWAVE RADAR is a new tool which will make the collection of this data easier for blast researchers. The data collection technique ensures that a large amount of face velocity data is collected from a blast, and describes the velocity characteristics of the face at a new level of detail. This results in a greater understanding of the effect of drilling and blasting parameters on blast performance. Several case studies are presented which illustrate the collection technique, the type of data generated and how the data is used.

Jan 1, 1992

By R Turner, P Hatherly, T Medhurst

Borehole geophysical logging data are routinely acquired during exploration of coal deposits in Australia. These data are commonly used qualitatively to identify and correlate coal seams and geotechnically significant interburden rock units. Some quantitative analysis, such as using sonic logs for rock strength estimation is becoming increasingly widespread. This paper discusses results from a project aimed at expanding the quantitative approach to more detailed mineralogical and lithological analysis, which leads to improved geotechnical characterisation for mine planning and mining hazard reduction. A standard suite of wireline logs measuring density, natural gamma, sonic and neutron were analysed from three coal mines in the Bowen Basin. Thirty-nine samples from cored sections of the boreholes were analysed by X-ray diffraction, spectral gamma counts and hyperspectral scanning. Using a standard petrophysical approach to calculating porosity, shale and matrix components from a combination of density, natural gamma and neutron logs, a good correlation with observed mineralogy was demonstrated. However, unusual mineralogies such as heavy minerals or low-potassium clays may distort this analysis. Simultaneous evaluation of all available geophysical logs by modern data mining methods was able to show how these ambiguities may be solved.

Jan 1, 2006

Over the last 20 years the mining industry has played a key role in the further development of many Central Queensland and New South Wales communities. The number of people who are employed by the coal mining industry, the number of transient residents, shift work and the town facilities have all contributed to how the community views the coal mining industry. As the coal mining boom continues and the mining communities continue to grow more emphasis is needed to address the community concerns, specifically the socio-economic and environmental impacts that the coal mining companies may have on these communities. Central Queensland coal mining operations are situated in the Bowen Basin. Many of the towns in the region have been developed specifically for the coal mining industry with 13 - 50 per cent (Australian Bureau of Statistics, 2006) of people living in the communities being directly employed by the mines. The introduction of shift work, differing rosters and the mining boom have resulted in considerable changes to these communities with more transient contractors and permanent employees taking up residence outside of these communities. This change, however, has not been as noticeable in the Hunter Valley region. The Hunter Valley, situated in the Sydney Basin has two main mining towns, Singleton and Muswellbrook. Of the 37 173 (Australian Bureau of Statistics, 2006) people that reside in the communities 13.8 to 16.5 per cent (Australian Bureau of Statistics, 2006) are employed directly by the mines. The Hunter Valley is a large tourist destination due to its many vineyards; this results in a diverse community where mining is not the sole means of employment. Similar to Central Queensland the mining boom has brought more people to the Hunter Valley region, although greater percentages have taken up residence in the communities. The views vary between the two regions on the coal mining industry, specifically on the socio-economic and environmental impacts that the industry may have on the surrounding communities.

Jan 1, 2008

By Meyer T

Sunburst PCF (Penetrating Cone Fracture) technology has recently undergone extensive underground field trials at Leinster Nickel Operations, Western Australia. Trials with the Sunburst machine started in September 1994 and continued through to December 1994 during which approximately 130 metres of tunnel were developed. The Sunburst technology was used to excavate sub-levels through ultramafic nickel ore for future sub-level caving operations at the Perseverance nickel mine. The Sunburst machine demonstrated reasonable instantaneous advance rates, however, there are still a number of future developments/design changes which need to be addressed prior to the PCF technology being trialed again in a production environment. This paper benchmarks conventional drill and blast at Leinster against the Sunburst Excavator machine performance within similar tunnel dimensions and rock conditions. In addition to productivity and cost information; environmental considerations, support and labour requirements are also discussed. Problems with the current machine design are highlighted and possible future design changes are suggested. The Sunburst machine could be a suitable technology for advancing development through weak to moderate rock conditions and may also reduce overall support costs. With the potential for automation and the ability to reduce rock damage into the development tunnel walls, it is proposed that the Sunburst machine warrants further consideration.

Jan 1, 1995

By Simmons SF, Fleming J

Alteration and mineralisation at the Island Copper deposit is related to the intrusion of Early Jurassic quartz feldspar porphyry dykes into surrounding comagmatic Bonanza volcanic rocks. The pyrophyllite alteration zone forms an upward flaring cone, largely hosted within a breccia body that c ross-cuts the Cu, Mo, and Au-rich ore shell. This alteration zone contains pyrophyllite, dumortierite and diaspore and resembles alteration occurring in some high-sulfidation deposits, but which is barren. Fluid mineral equilibria and fluid inclusion studies indicate formation at approximately 300 ¦C from fluids dominated by steam and gases. These fluids appear highly acidic, but sulfur poor, leading to extreme base leaching within the breccia body and surrounding rocks.

Jan 1, 1995

By Totterdell JM

The Permian-Triassic Bowen Basin and the Jurassic-Cretaceous Surat Basin evolved in a backarc tectonic setting behind an active convergent plate margin in eastern Gondwana. Several extensional (Early Permian; Eocene) and contractional (mid- Permian; Early Triassic; Middle-Late Triassic; early Late Cretaceous) intraplate deformational events are recognised in the basins. These can be correlated with similar events in the New England Orogen that was being deformed in the Late Permian- Late Triassic as a foreland thrust belt. The intraplate deformations were probably the consequence of plate interactions, including the accretion of terranes, at the ancient active plate margin, remnants of which now occur in New Zealand.

Jan 1, 1995

By Stanton RL

Stratiform lead-zinc mineralization in the Soldiers Cap Group and Kuridala Formation of the Mount Isa Inlier is closely associated with iron-rich sedimentary units or "iron formation", and has many similarities to the Broken Hill deposit in New South Wales. Both the Soldiers Cap Group and the Kuridala Formation have been intensively explored for deposits of this type since the early nineteen- seventies. A mineralized belt of at least eight significant prospects has been identified, of which the Pegmont deposit is the largest and best known example. In most cases the mineralized horizons contain banded galena and sphalerite within a gangue of predominantly quartz-garnet- pyroxene-amphibole rock, sometimes containing a variety of other metamorphic silicates, and apatite. Chemically, the mineralized horizons are distinguished by higher than usual levels of one or more of total Fe, MnO, CaO and P205. Interpretation of patterns of mineral- ization within the belt is based on the Pegmont deposit, where a model of base metal sulphide deposition within restricted basins of iron-rich chemical sediment has been developed (Stanton and Vaughan, 1979). Broadly, the model envisages the deposition of higher grade lead-rich mineralization in the basin centre position, lower grade zinc- rich mineralization in a basin intermediate position, and much weaker copper-rich mineralization in a basin edge position. These three positions reflect a laterally continuous arrangement of silicate microfacies within the original iron-rich sediment.

Jan 1, 1984

By Frazer E. J, Lwin T

Measurements of coulombic efficiency (QE) for zinc electrodeposition were carried out under mass-transfer-controlled conditions using a rotating disc electrode in synthetic acidic zinc sulphate solutions. Various methods of solution preparation and purifi- cation were investigated using reagents vary- ing from analytical grade to high purity; the purest solution was obtained-by dissolving 99.9999% zinc (Koch-Light) in sulphuric acid solution (BDH Aristar). Improvements in sol- ution purity did not necessarily increase QE, especially where apparently beneficial impur- ities (e.g., Pb) were initially present. The maximum QE obtainable through variation of temperature (T), current density-(i) and elec- trode rotation rate was established using a statistical optimization technique. The QE was determined principally by T and i, with significant interaction between these factors in the highest purity solution. QE contours, which gave an overall view of solution per- formance, were constructed and predictions about the response under conditions similar to plant practice were made. Wark's Rule (the dependence of QE on zinc/acid ratio) was obeyed in the purest solution over the range of composition commonly encountered in zinc plants. High concentrations of Na2SO4 and K2SO4, which occur in some plant solutions, were found to increase QE marginally ("1.2%). The intrinsic effects of individual impurities such as Cu and Ni were evaluated by additions (up to 5 ppm) to the purest solution. Decreases in QE were found to be minimal at the impurity levels normally encountered in zinc plants.

Jan 1, 1987

By Fountain C. R

In April 1987, Mount Isa Mines Limited (MIM) commissioned an ISASMELT reactor to smelt 15t/h of copper concentrate at the Mount Isa Copper Smelter. This unit was based on the Sirosmelt lance technology and incorporated features proven in the Lead ISASMELT plant which has been operating in the MIM Lead Smelter since 1983. From April 1987 to June 1989, the copper smelting plant treated 167000 tonnes. Concentrate, coal and fluxes are fed continuously to the furnace. Oxygen enriched air is injected through a lance which is submerged in the slag bath. Matte and slag are tapped together through a single taphole into a reverberatory furnace, and from there are treated with normal reverberatory furnace production. Advantages of the process include its ability to eliminate most lead and arsenic in feed, its flexibility with respect to feed composition, sizing and moisture, and the plant's low capital cost. Acceptable refractory life has also been demonstrated. The commissioning of a 70 t/day oxygen plant has rerated the plant from 15t/h to 18t/h while allowing a reduction in fuel usage of one third. A trial using 150 t/day oxygen was carried out in May 1989, and showed that the furnace could treat 48 t/h chalcopyrite concentrate while maintaining a very low fuel requirement. The oxygen trial results have given considerable confidence for plant scale-up. Detailed project evaluation is currently underway for the replacement of the roaster and reverberatory furnaces at Mount Isa with a single 110 t/h ISASMELT reactor.

Jan 1, 1989

By Hamilton TM

The Holocene Minninup shoreline is a coastal barrier system stretching from Bunbury to Busselton, in southwestern Australia. It has developed in a microtidal swell wave environment, under the influence of the post- glacial marine transgression and Holocene sea level variation. Barrier sediments thin rapidly across a shallow shelf, and consist of quartzo-felds- pathic sands with a minor skeletal carbonate component. Holocene shelf deposits are laterally extensive sheets overlying Pleisto- cene limestone. Modern carbonate production is small. Development of the Minninup barrier system has been controlled largely by low rates of sediment input from terrigenous and carbonate sources, late Holocene sea level fluctuati,.,s, and pre-existent coastal landforms composed of Pleistocene limestone. Modern controls on sedimentation are the refracted, shoaling swell wave regime, and onshore winds, which combine to promote nett northward longshore drift. Holocene barrier systems of the southern Swan Coastal Plain are of several different types. These include prograded sequences of beach ridges overlying shoreface sediments, such as is found at Rockingham and parts of Geographe Bay, and complex polygenetic systems typified by the Leschenault Peninsula. Pre- liminary investigations of the barrier stratigraphy of the Minninup shoreline indicate that both progradational and polygenetic sequences are present. The processes involved in shoreline development and heavy mineral accumulation are being studied using aerial photograph inter- pretation, beach profile monitoring, sampling, and granulometric analysis. This will lead to an enhanced understanding of the mechanisms of heavy mineral accumulation, and assist in the development of genetic models as aids for Exploration.

Jan 1, 1986

By T Leach, I Pringle

The Bowdens Silver Deposit is a low sulfidation epithermal silver-base metal deposit that has formed on the northern margin of a hydrothermal system within air-fall breccias, ignimbrites and crystal tuffs of rhyolitic composition. The deposit lies near the north-eastern margin of the Lachlan Fold Belt and the rhyolitic host rocks are of Early Permian age. The silver mineralisation occurs as flat-lying zones of disseminations and silicic fracture-filling within the Rylstone Volcanics and is closely associated with sulfides of iron, arsenic, lead and zinc. High-grade silver mineralisation is also found in steeply-dipping fracture zones which host banded sulfide veins. Studies of the alteration products indicate that high temperature fluids, flowing from south of the current project area, resulted in quartz (¦adularia) û illite/sericite alteration. Cool, low pH steam-heated waters on the northern and eastern margins of the prospect area resulted in siderite û smectite-illite clay û Fe-carbonate û marcasite û kaolinite alteration. Mixing of the two fluid types resulted in the deposition of iron and base metal sulfides, a decrease in both sulfur activity and pH of the mineralising fluid, and subsequent silver mineralisation.

Jan 1, 2004

By U Briem, R Verreet

The level of wire rope technology used in mine hoisting applications has a significant effect on the overall efficiency of the hoisting system. This paper discusses the effect that a reduction in rope mass per unit length and an increase in rope breaking strength can have on rock skip capacity and hence mine shaft output. A 20 per cent reduction in rope mass per metre for a typical 48 mm hoisting rope, while maintaining the breaking strength, increases the skipÆs capacity by circa 30 per cent at a suspended rope length of 3000 m. Such gains in shaft output, without any significant changes to the shaft or winder design, can have major implications for the feasibility of future deep mine projects. The technical challenge for rope manufacturers is how to get rid of 20 to 30 per cent of the rope mass while keeping the breaking strength and modulus of elasticity of the whole rope constant. CASAR are currently developing steel wire rope constructions where the steel IWRC has been replaced with high strength, high modulus fibres such as Kevlar«, Spectra« and Dyneema«. One of the key aspects of such composite rope designs is to ensure equal load sharing between the different rope components, ie in proportion to their area. If there is a significant difference in modulus between the fibre core and the steel outer strands, the core may not carry its proper proportion of the load and the outer strands would be overloaded. Some technical aspects of the design of composite steel wire ropes are discussed. A design and operational issue that needs careful consideration is the safe non destructive testing (NDT) of composite ropes. Traditional magnetic NDT would only be capable of inspecting the steel wires. Techniques therefore need to be developed that would give operators a reliable indication of the condition of the load bearing fibre core. This paper also discusses possible solutions to this very important NDT question.

Jan 1, 2005

This paper contends that optimisation of energy resources through active control and predictive simulation modelling is possible, and that such monitoring leads to large savings in the electricity costs of hot mines (where refrigeration has to be employed). In addition, active monitoring and control can positively affect the establishment of a safe, healthy and productive working environment. In the entire optimisation process certain guidelines were set to ensure that the requirements of the Mine Health and Safety Act were met (South Africa). Varying the quantity of air supplied underground by means of variable speed drive (VSD) fans is one of the crucial factors in the interactive approach towards the optimisation of ventilation, as is refrigeration and the pumping requirements associated with refrigeration. This article highlights the interaction between the amount of air supplied and the effect it has on refrigeration requirements underground. This article also considers the effect that this would have on contaminant control. Various tools are available for ventilation and cooling design for mining. A lot of these tools are based on the assumption of steady state conditions and do not take into account instantaneous changes in conditions, day-to-day, or hour-to-hour (such as for temperature and contaminants). They also do not take into account the optimisation of energy resources related to the creation of the acceptable underground conditions. With these tools worst-case and best-case scenarios are identified, and strategic decisions are made accordingly. Currently, the amount of the fresh air, the velocity of the air, and its general temperature in the mine are only changed when one production phase changes into another (or when unacceptable conditions occur as a result of poor design or neglect). This means that during a specific production phase (which can last for several months), there can be an oversupply, or undersupply, of energy resources, which will obviously affect the concentration levels of the various contaminants (through under or oversupply of air).

Jan 1, 2005

Small mines exist because of a restricted deposit or a small market. With the right management at the present time the small mine can have lower total costs than larger mines. Charbon is an example of a small mine with a restricted deposit and a specialised product. The development which incorporates a unique rail loading facility and flexible coal preparation plant was achieved with a modest capital outlay and in record time. To remain competitive in future with large scale mines who seek increased production the small mine must achieve increased productivity through automation, higher speed equipment and a multiskilled workforce. Deregulation of the industry, scrapping the Coal Industry Tribunal and the Joint Coal Board would benefit small mines greatly. Management of a small operation also requires multiskills which need to be supported by outside help in the form of consultants and temporary staff. In the 21st century small mines will continue to provide a service to the market.

Jan 1, 1988

The sharp deterioration in Au~tralia'S ternn of trade in recent years and the accumulating national debt highlight the need for a restructuring of the economy which is highly dependent upon primary agricultural and mineral commodity exports (figure 1). Table I gives an indication of the value that can be added to raw material by mineral processing. Significantly higher value is added through downstream manufacturing. In 1987, the mining and rural sectors accounted for 47010 and 38010 respectively of total exports valued at $35,782 million (figure 2). The export contribution from minerals comprised $12,266 mil- lion from unprocessed ores and concentrates and $4,668 million from metals and processed minerals including some simple manufactures. Coal accounted for 450/s of total primary mineral exports. Iron ore and alumina are other important mineral exports, while gold and aluminium are major metal exports. (Figure 3) Australia's minerals are now traded in a much more competi- tive and oversupplied market in contrast to the 1960's and 1970's period which was characterised by increasing exports of largely unprocessed ores and concentrates. Since the early 1980's (I cI) resscd )ver~cas nutrkcts and km rununodlity liriccs ha~c hcen the product of excess capacity installed to satisfy a forecast high growth in demand which never eventuated due to the world reces- sion. During this period the emphasis on technology development was focussed on reducing costs through increased production effi- ciencies in order to maintain competitiveness.

Jan 1, 1988

At 9.45 pm on Thursday, 12 July 1962 glass began to flow in an endless stream from a massive melting tank in a new Whangarei factory and a vital new industry was born û right on schedule. It wasn't good glass. It was ridged. It cracked. It rippled. It obstinately refused to emerge upstairs in the cutting room in one solid continuous sheet. But all through the night, drawing speeds were adjusted, temperatures changed. And on Friday morning, at 8:30, it finally came through as sheet û not perfect as yet, but sheet glass all the same. The rest is only a matter of time. Unfortunately, the buoyant enthusiasm displayed by the founders of the sheet glass industry in New Zealand, and the technical expertise of their European consultants, failed to bring the glass quality up to commercially acceptable standards and within six months, the company was in receivership. Taking over the role of producing New Zealand's sheet glass requirements, New Zealand Window Glass Company was formed as a partnership between two companies with long experience in sheet glass manufacture û Pilkington Brothers (NZ) Limited and Australian Consolidated Industries Limited. This paper sets out to identify the raw material requirements and controls necessary for the successful manufacture of sheet glass, and the availability and supply of suitable materials for use at Whangarei.

Jan 1, 1978

Reliable sampling practices are the key to optimising the market value of a mining or chemical companyÆs stock. As a result, reliable sampling standards are needed. However, current standards on sampling present the æuniversalÆ Pierre GyÆs Sampling Theory in an ambiguous way. For example, the Total Sampling Error is divided into its basic components only in informative annexes, when it should clearly be the main body of the standard. Sampling standards are presently loaded with statistical concepts that actually belong in the annexes. Furthermore, many non-probabilistic sampling procedures are still mentioned which do not belong in a standard. The objective is not to criticise existing sampling standards, but to suggest better ones. Sections on the Sampling Theory should divide the Total Sampling Error into a sum of its nine basic components. Then, and only then, should they be addressed one at the time. Sections for establishing a sampling protocol should address the in situ Nugget Effect, the Fundamental Error, the Grouping and Segregation Error, the Long Range Quality Fluctuation Error, and the Periodic Quality Fluctuation Error. Sections for sampling methods, mechanical sampling, manual sampling, grab sampling, sampling of trucks, railroad cars, bags, and drums should be part of the critically important practical implementation of a recommended sampling protocol, called Sampling Correctness. It includes the increment Delimitation Error, the increment Extraction Error, the Weighting Error, and the Preparation Errors. Unless these errors are addressed one at a time, in an unambiguous way, the standard will remain ineffective in solving sampling problems for the industry. Therefore, a strategy is needed to create better standards required at the early stages of new projects, both by manufacturers of sampling equipment and by engineering firms. A logical sequence of important points that cannot be ignored in any sampling standard is presented. An analysis of the practical use of the words sampling uncertainty versus sampling error is recalled. Finally, as a practical example, an in-depth analysis of the correctness of cross-belt samplers is presented, and emphasis is placed on the correct ways to perform bias-tests for mechanical sampling systems.

Jan 1, 2005