Search Documents

Electrochemistry Measurement, Using Chena Analyser, to Investigate Selective Separation of Pentlandite and Pyrrhotite

Sep 13, 2010

By S Jackson, I Arbuthnot

The use of High Rate Thickeners has gained wide acceptance in the mineral treatment industries. The design of these units is characterized by an efficient deaeration and flocculation chamber, and introduction of the flocculated feed solids into a preformed floc bed zone. By these means the settling process is accelerated and consequently High Rate Thickeners achieve a significantly higher throughput per unit area than conventional thickeners.   The object of a control system on a High Rate Thickener (HRT), as on a conventional thickener, is to obtain the required underflow density and overflow clarity at all feed conditions. The feed conditions which may vary include volumetric and mass feed rate, pulp density, particle size and particle type. A conventional thickener has a large volume and cross sectional area, and changes in performance occur slowly û the operator has time to observe and react to these changes to maintain control. On a HRT, there is a much reduced residence time and therefore control parameters need to be reset more frequently. Although manual control is possible, the use of automatic control systems is therefore desirable to avoid excessive operator attention, while optimizing control of density and clarity. Automatic control of a conventional thickener is usually achieved by an underflow density loop which regulates the rate of withdrawal of underflow. A turbidity meter is sometimes used to measure overflow clarity and regulate the addition of a coagulant or polymer flocculant. These measures are not adequate on a HRT, because they would not give optimum control and could lead to excessive flocculant use. To achieve optimum operation in a HRT, the floc bed level should be maintained above the feed inlet point in the thickener. This bed level has become the key variable around which most control systems have been designed. However, a number of problems have occurred which has resulted in poor control, or only partial control of thickener performance. We will describe some of these problems, and a solution which is simple and effective.

Jan 1, 1990

A BRIEF DESCRIPTION OF TELPHER HANDLING AND BLAST FURNACE EQUIPMENT.The various sections will be described in the following order:(a) Telpher Handling and Storage Bins.(b) Blast Furnaces.(c) Slag Disposal.(d) Bullion Handling to Drossing Kettles.(e) Copper Drossing.(f) Copper Matte Furnace.(g) Bullion Delivery to Refinery.(h) Fume Handling.(a) TELPHER HANDLING.The telpher installation is an all-steel structure designed to carry out the work of assembly and delivery of charge materials to the blast furnaces.To simplify description, the primary telpher installation will be divided into three (3) sections:-No. 1 Section. 395 ft. long, running north and south, parallel to the water front, and so located that coke, which...

Jan 1, 1937

Ledcap Pty Ltd has developed two software tools for assisting in the determination of life-of-mine (LOM) trucking requirements. The first tool generates haul paths and the second calculates truck travel time over these paths. The two step approach allows the paths to be viewed and if required edited, to better represent the actual site haul routes.The first tool automatically creates haul paths between the mine bench and the dump. To do this the user supplies a master haul route and a scheduled block model. The master haul path and the block model are interacted to create multiple haul routes, one for each pit/dump bench pair in each scheduling period. Each path carries with it a record of the scheduling period it represents and the dry tonnage hauled over the path in that period.The second tool calculates truck travel time over the path. Data from the manufacturer's rimpull and retarder curves are used to calculate accelerations and speed over each segment of the haul path. As the paths are derived from digitised representations of mine haul routes the path f les often have over a hundred segments. This detailed representation of the haul route allows the software to automatically adjust speed for different radius corners and accurately simulates the changing accelerations over the gradient changes that occur in real life mine ramps. Rolling resistance can be specified at a global level, at a segment level and at a period level. This allows rolling resistance to be changed seasonally as well as spatially.Life-of-mine trucking studies attempt to calculate an accurate answer from extremely variable inputs. This paper will detail the features of the two software tools and how the tools provided in the software can assist the mine planner to have greater confidence in their life-of-mine trucking requirements and the subsequent production capacity inputs to their scheduling calculations.

Dec 6, 2010

By G du Toit, P L. Gillot, M Swanepoel

Randgold Resources’ Loulo-Gounkoto Complex is one of the largest gold mining operations in Mali, West Africa. The mine, which is situated on the western border with Senegal, treats more than 4 Mt/a of ore through a conventional three-stage crushing and ball milling circuit followed by a carbon-in-leach plant. Ore supply is achieved by a combination of open pit and underground mining, with the majority of the ore supply sourced from the Gara and Yalea underground mines situated approximately 2 km and 6 km respectively from the gold plant.In 2011, Randgold Resources commissioned Golder Associates to perform an evaluation study for providing structural backfill to both the Gara and Yalea underground mines using the current gold plant tailings. The test work performed as part of the evaluation study concluded the need for a tailings cycloning and dewatering facility capable of producing slurry at a solids concentration of 65 per cent with a particle size distribution that had minimum 25 per cent passing 20 µm and less than 5 per cent of -5 µm material. Tailings desliming was required to ensure a consistent feed quality to the paste preparation plants and to ensure that the system would be capable of handling variation in the feed composition from the gold plant.WorleyParsons, previously TWP Projects, was contracted by Randgold Resources to complete the engineering design for the slurry preparation plant, whilst Golder Associates was retained to complete the engineering design of the two paste preparation plants.This paper discusses the test work, design considerations and engineering design of the slurry preparation plant, termed the ‘intermediate plant’, as well as all ancillary facilities required for the delivery of the deslimed slurry to the paste preparation plants located at the two underground mines.CITATION:Swanepoel, M, du Toit, G and Gillot, P L, 2014. Case study – engineering design for a slurry preparation plant for a paste application in West Africa, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 477–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Wetting Characteristics of Mineral Surfaces - Contact Angle Measurements through Molecular Dynamics Simulations

Sep 13, 2010

By Matters C. W

THE following paper embodies the present practice and the results of past experience in the survey departments of two of the leading Broken Hill mines, the Central (Sulphide Corporation Ltd.) and the Broken Hill South S. M. Co. N. L.The authors intend to limit the scope of this paper to a consideration of office methods, as much has recently appeared in technical literature concerning field work, both surface and underground. Special reference may here be made to a valuable paper on 'Mine Surveying' by H W Gartrell, in Vol XIII of Transactions, in which the author gives considerable attention to field work. Moreover, much of the office work described in current literature is American, and sometimes not suited to local conditions, being ·often exceedingly elaborate and demanding a large staff of assistants. It is believed that the methods of recording information described in this paper are sufficiently simple and flexible to be adapted to most Australian mines. Brief acknowledgement must be made to the work done by Americans, who have raised mine surveying to the position of a separate profession, instead of being merely an unimportant branch of land surveying.

Jan 1, 1912

In spite of the many contributions that have been made to our knowledge of the creep properties of polycrystalline lead, the precise influence of various factors on these properties is not yet fully understood. Indeed, the position is such that several important points in connection with the creep of lead are a matter of controversy. This has been brought about largely by the fact that, in the case of lead, the changes that are produced in the creep behaviour by slight variations of such factors as the purity, grain sizeand previous treatment are out of all proportion to the magnitude of these variations.In order to study the fundamental properties of lead as related to creep, and so gain a more enlightened perspective with which to consider the creep of lead in general, the work that is described in a series of papers, of which the present paper is the third part, has been carried out. It deals with lead in the form of single crystals.It has been shown (1) - (3) that the grain boundaries as well as the actual grains play a part in the creep of polycrystalline lead. The present work, by eliminating grain boundaries, enables the. contribution of the grains themselves to the process of creep, in other words, crystalline creep, to be studied effectively.This object was, possibly, the major one in this work.

Jan 1, 1940

Thickener Modelling - Incorporating Shear Effects

Sep 13, 2010

Removal of Dilute Toxic Anions in Wastewater Using Aluminum Hydroxides Co-Precipitation Method

Sep 13, 2010

The Autogenous Fine Grinding Kelsey Axial Displacement (KAD) Mill The marginal improvements which continue to be made to fine grinding practices have exposed the limits of conventional technologies and highlighted the need for a radically new approach. The patented autogenous Kelsey Axial Displacement (KAD) Mill design consists of a rotating spherical grinding chamber, which shares the same spherical centre as the shaft-mounted counter-rotating disc assembly. The axis of the disc assembly can be inclined to the axis of the spherical grinding chamber by pivoting the disc shaft about the common spherical centre. The inter-particle energy transfer required for breakage results from particle velocity differentials created by the discs intercepting the rotating mass. Particle size reduction is concentrated in high shear zones, which envelop the outer surface and periphery of the discs. This paper traces the development of the KAD Mill from pilot to commercial scale. Pilot work covers a range of minerals including magnetite, calcite, dolomite, barite, limestone and talc. Test results include open and closed circuit operation in wet and dry modes. Conventional milling constraints and energy consumption issues are addressed while new dimensions are added to the feed size range acceptable for wet and dry grinding to fine and ultra-fine sizes.

Sep 13, 2010

Various steps, and complete sequences, for the recovery of lead and zinc from a mixed sulphide concentrate, high in silica and pyrite, have been tested.Oxidation steps of roasting in air or in a sulphating atmosphere and use of aqueous acidic, ammoniacal, and near neutral oxidation media were compared. Oxidation roasting or use of acidic media appeared most useful. Procedures for dissolution of zinc from calcines using sulphuric and sulphurous acid to avoid silica gelation problems are compared and a direct leaching procedure with sulphuric 'acid at controlled pH shown to be the most useful.Methods for the removal of germanium, nickel, and magnesium from zinc sulphate solutions prior to zinc electrodeposition were tested. The recoveries of zinc from ammoniacal solutions by electrolysis and distillation are compared.The dissolution of lead compounds from the residue of zinc extraction by amine and ammoniacal ammonium sulphate (AAS) solutions Was tested. Lead, sulphide was precipitated in filtera'ble form from AAS solutions. The reduction of lead sulphate to lead sulphide with sulphur was difficult, but possible. The various steps were used to deveiop five complete processing sequences, of which two were shown to be technically feasible and have potential economic viability.

Jan 1, 1975

By Laros T, Schoenbrunn F

Deep paste thickeners have been proven capable of consistently producing medium to low slump material for disposal without the need for filters. However, proper design of the entire system is critical for a paste project to he successful. Some of the factors that must be carefully considered in design of a paste system include thickener sizing, tailings inipoundineni design, underflow pumping, and control system.

Jan 1, 1998

It is difficult to evaluate exploration properties in a manner that is transparent, repeatable and easily re-calculated to cater for different geological interpretations, but the risk-based assessment methodology, the Geological Risk Method, developed and described by Lord et al (2001) attempts to satisfy all these criteria. This paper examines a case study example based on valuations of exploration projects conducted by SRK Consulting using this methodology, and describes some of the advantages and limitations of the method.

Jan 1, 2007

Recent data contributions to New Zealand Mesozoic terrane geology confirm the consensus interpretation thatNew Zealand grew by the progressive addition of material by plutonic and accretionary processes along the Gondwana margin. The data also: 1. emphasise the discontinuous but inter-related nature of these processes of continental growth, 2. better establish a direct Gondwana correlation of the Western Province and probable Gondwana provenance of at least some of the Eastern Province, 3. suggest specific times and places when passive or strike-slip rather than subduction regimes are recorded along the south Gondwana margin, and 4. potentially lead to interpretations emphasising parautochthonous rather than far travelled relationships between many New Zealand terranes.  

Jan 1, 1995

Whether you are an employee, contractor or consultant working in the mineral industry, there are pressures to deliver the best possible performance. Technical professionals are usually driven by an internal desire to perform to a high standard because of personal pride in their profession, but there are an increasing number of external requirements to demonstrate that the actions taken were based upon reasonable grounds and that the work conformed to current best practice. People expect these best practice procedures to be followed and governments are now requiring those tendering for contracts to be registered in some way and to be participants in quality assurance schemes. One is not immune to these pressures just because you are working in a less legislatively sophisticated developing country in the circum-Pacific rim (pacrim) region.   Among the external pressures are the general ethical requirements of the professional body to which the person usually belongs, e.g. The Australasian Institute of Mining and Metallurgy (AusIMM), which are further elaborated upon in various Codes and Guidelines on specific matters, e.g. JORC (ore reserves reports) and VALMIN (assessment and valuation reports). These are outlined and discussed. Also, AusIMM's Chartered Practicing Status (CPS) Proposal is outlined in the context of other Pacrim countries approach to registering of technical professionals, which is a way of ensuring that minimum standards of qualifications, experience, competence and repute are demonstrable to ones employer (or client), peers and the wider community, including government.   Today, in the external working scene, there are many laws (particularly those applicable to the corporate and environmental spheres), with which contractors/consultants and even employees must fully comply, or else face criminal sanctions involving huge fines and imprisonment. These, too, are outlined and discussed. One must be able to mount a due diligence defence to avoid or mitigate these consequences.   Personal liability in the context of the day-to-day performance of one's duties has thus become a major concern to the technical professional and the ways in which it can be ameliorated, or insured against, are described. However, for some mineral industry practitioners, the problem is exacerbated because. of their general ignorance of the extent of their personal liability exposure. This paper intends to address this ignorance and to heighten general awareness of personal liability issues, as well as proposing some simple ways to limit this liability.

Jan 1, 1995

THE object that the writer has mainly in view in presenting this paper is to draw the attention of those connected with the technical side of the industry to the unsatisfactory and by no means up-to-date methods employed in estimating the tin contents of an ore. At the same time, what is regarded, from the writer's personal experience, as a satisfactory and reliable method is explained in detail. It is a curious fact that for the last 25 years tin·assay methods have made little or no advance, while those now in general use ill connection with copper and lead ores can scarcely be compared with those then obtaining, so greatly have they been improved upon. Though it. is not altogether expected that the method herein advocated will at once meet with general approval, the writer hopes the resultant discussion may bring out points that have hitherto escaped detection.FIRE METHODSThe old Cornish method of smelting with anthracite is now obsolete. The cyanide assay, although unreliable, is still much used because of its simplicity. In the Malaya many buyers of tin ores use the cyanide assay, the smelting being carried out generally in a benzine furnace. It is essential that the smelting with cyanide be performed at a low temperature. Even then, impurities, such as Sb2S3 and...

Jan 1, 1912

The final criterion of the payability of gold production must necessarily be the cost per ounce. While the cost per ton or per cubic yard is a convenient comparative measure, and a necessary one for operating control, it is obviously insufficient as a means of judging whether or not, in a given set of circumstances, a gold production operation can be carried out economically.. An alternative method, which brings in the ton or cubic yard as a unit of measurement, is to determine what the cost per ton or per cubic yard is equivalent to, in terms of pennyweights or grains at the ruling price of gold. But this is really only another way of stating that the cost per unit of product is the ultimate measure of profit or loss, and not the cost per unit of input material.It is accordingly of interest to determine the cost per ounce of Australian gold production and to compare it with the cost of gold production in some other parts of the world which are important gold producers. The attached Appendix, which it, is believed comprises practically all Australian mines of any consequence (except Big Bell and the de Bernales group, for which. insufficient information is available), shows this information for financial years ending between 31st December, 1938, and 31st December, 1939, the production of gold dealt with being some 1,084,000 oz., or 66% of the total Australian production for 1939. For comparative purposes the cost of producing gold at representative mines in New Guinea, New Zealand, Fiji, Canada, India, West Africa and Rhodesia, and the average cost of production at the Rand mines, has also been included.It is obviously necessary in a study of this sort that the basis of the cost should be clearly set out and should be as nearly as possible uniform. The "cost" as calculated herein comprises the following items:

Jan 1, 1940

By M Nagarajan, S Esen

This paper presents three case studies from three surface coalmines. The first case study is from a coalmine where a dragline operates in 60 m wide and 1 km long strips. Typical overburden height ranges from 30 m to 50 m. The base case blast was modelled using an advanced blasting model (Distinct Motion Code – DMC) to establish the baseline using the blasting parameters in use before optimisation. DMC was used to model the alternative blasting scenarios to obtain the following key objectives:the post-blast muck pile profile was required to have an optimum height of ~28 moptimise cast percentageachieve a well-fragmented muck pile for the draglinethe muck pile profile should be appropriate for the dragline entry into the strip.Achieving these objectives would optimise the dragline performance through reducing rehandle and improving advance along the strip. DMC modelling resulted in the following outcomes:the required muck pile profile could be achievedthe cast percentage increased from 21.1 to 25.1 – a four per cent increaserehandle volumes were reduced.Establishing a good quality assurance / quality control (QA/QC) process was essential to delivering a blast that could achieve these outcomes. The blast was fired successfully and the dragline completed the strip approximately two weeks ahead of the time taken for the previous strip.The second case study is from a coalmine where D11 dozers are used to move the blasted material to the spoil. An optimum profile was required for the dozers for this low-cost mining operation. To achieve this, an electronic blasting system (uni tronicTM 600) was introduced to optimise the muck pile profiles being delivered. The new muck pile profiles showed improved cast percentage from 10.6 per cent to 17.8 per cent. The changes in the muck pile centre of mass displacement improved dozer efficiency as a result of pushing material shorter distances to its final position. Dozer productivity (bcm/h) statistically did not change but coal was being exposed at a faster rate.The third case study summarises the results from a site where dozers are used to minimise the total mining cost. Traditionally, excavators had been used on-site with conventional blast designs. After firing the first cast shot, the blasted material was found reasonably well-fragmented. Although dozing productivity hasn’t been quantified on-site, operators were providing positive feedback (easier push) due to the reasonably good muck pile profile suiting to the dozers. This site also realised significant savings with the dozing as compared to their truck/shovel operation.CITATION:Esen, S and Nagarajan, M, 2015. Muck pile shaping for draglines and dozers at surface coalmines, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 409–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Australia's iron ore industry is entering a challenging period with the development of new orebodies, the introduction of new products and the push for further downstream processing. In addition, the recent price reductions for iron ore exports have intensified the focus on reducing capital and operating costs. To assist in these areas, CSIRO is expanding its research capabilities, including the incorporation into CSIRO of the Mineral Processing Laboratories in Perth, which were previously managed by the WA Department of Minerals and Energy. In addition, a large part of the $24.4 million expansion of CSIRO's Pinjarra Hills laboratories in Brisbane will be devoted to enhancing iron ore processing research, providing purpose built laboratories and large process bays.

Jan 1, 1999