Search Documents

By I. Haskett

ABSTRACT The Redwater pool, in north-central Alberta, was discovered in October, 1948, and at the end of 1950 was about 85 per cent developed. Production is from a Devonian coral limestone reef and is found at an average depth of 3,150 feet. The pool has an estimated .productive area of 37,000 acres, and a maximum oil zone thickness of slightly over 200 feet. Wide variations exist in both type and values of porosity, with the average value determined for the reservoir being 6.16 per cent. The total stock tank oil in place is about 1.24 billion barrels. The crude has a saturation pressure of 485 psig, com-pared to the original value of 1,050 psig for the reservoir, and the principal recovery mechanism so far has been the natural water drive. Cumulative production to January 1st, 1951, has been about 15.5 million barrels. These withdrawals resulted in a reservoir pressure decline of slightly over 100 psi. Predictions of future behaviour indicate that the water drive will not be of sufficient magnitude to maintain the reservoir above saturation pressure past 1953, and that, with natural depletion, the pool will be produced largely by a solution gas drive. Pressure maintenance by water injection has been considered and the possibility of raising the pressure to the original value of 1,050 psig is also discussed. INTRODUCTION WITH the discovery of the Lewduc pool, early in 1947, the Devonian limestone became the major geological formation contributing to Western Canada's rapidly growing petroleum reserves. Redwater, discovered in October, 1948, is now the largest known Devonian pool in Canada, with a recoverable reserve estimated at approximately 500 million barrels. Until recent years, the knowledge of the nature and characteristics of this type of limestone reservoir has been comparatively limited.

Jan 1, 1951

By Christopher W. Corti

A major aim of the GOLD 2003 conference, is to promote new gold related science and technology with a view to developing new useful industrial applications for gold. Current industrial uses have provided a steady annual industrial demand for gold of around 350-400 tonnes in recent years, the bulk of which is centred on electronics applications, with dental uses constituting the second largest application. However, there is good reason to believe that whilst gold will continue to play a major role in these sectors in the future, substantial growth of demand is not anticipated. Increased industrial demand for gold is only likely to come through the emergence of new applications, probably most significantly in five broad market sectors: ? Pollution and emission control technologies, including fuel cells. ? New uses for gold in advanced electronics, electrical systems and devices. ? Chemical processing of a range of bulk and speciality chemicals, using gold based catalysts ? Advanced coatings exploiting the novel properties of gold, particularly in nanoparticulate form. ? New biomedical uses for gold including medical treatments, drugs, implants, sensors and devices. There is cause for optimism that many new applications for gold could emerge in these sectors over the next decade and that this will lead to a substantial growth in demand for gold. It is clear that many of these new opportunities will be based on a chemical approach to synthesis of useful products rather than what has historically been a materials or mechanical approach. To turn this expectation into reality requires sustained support of R & D and a determination to exploit this new science and technology into viable commercial applications.

Oct 1, 2003

By L. Su, S. Liu, K. Jiang, K. Xie

The reduction of iron dissolution and acid consumption is fairly important in the extraction of Ni and Co from laterite ores from both economic and efficiency perspectives. BGRIMM conducted detailed research to investigate the behavior of iron in a nickel laterite leaching process. The mineralogy of Ni and Co was studied. In limonite ore about 76% of nickel is present in goethite while in saprolite ore 79% of nickel is associated with magnesium and silicon minerals. Test work revealed that limonite can be decomposed completely with enough acid concentration during atmospheric leaching. More than 98% of Ni and Co were leached into solution while 85% of the iron was also dissolved with 130-140 g/L iron in solution. Iron precipitates as hematite in the temperature range 250-270?C without neutralization reagents. That’s why limonite is treated by high pressure acid leaching (HPAL) technology to achieve nickel extraction and iron precipitation in the same autoclave. BGRIMM’s test results indicated that the remaining acid in atmospheric leaching solution and acid released by iron precipitation at a lower temperature was enough to leach saprolite efficiently. The so-called inverse leaching technology leaches limonite at atmospheric condition and the leaching slurry combined with saprolite is pumped into an autoclave to leach saprolite at 150-170?C. In the autoclave iron precipitates as hematite without acid consumption. Total nickel and cobalt extractions in the test program were more than 90% with iron content in solution below 8 g/L. In this inverse process iron dissolves in the atmospheric leaching stage and precipitates as hematite in the low temperature leaching stage. Compared with HPAL the leaching temperature is reduced to 150-170 ºC from 250-270 ºC. Compared to atmospheric tank leaching acid consumption is reduced from 850-950 kg/t ore (atmospheric) to 550-650 kg/t ore (inverse).

Jan 1, 2016

By Fraser Rowe

This paper discusses the philosophies, strategies, goals and pitfalls in automating a mine schedule. The intention of the paper is to give an open and honest view of who could benefit from moving to an automated system, what you can expect from such a system, and what you should be aware of. Many companies feel that moving to an automated mine planning solution will allow the mine scheduling engineer to push a button and walk away, but the reality is that is hardly ever the case. Part of that awareness comes from understanding what is meant by ?automated mine scheduling?, and this paper address that. By contrasting what is meant by ?manual scheduling? and ?automated scheduling? it is hoped that the reader can gain an appreciation of the entire process.

Oct 1, 2009

By Fidelis T. Suorineni

The Ashanti mine, located in Obusai, Ghana, West Africa, has been in production for over 100 years, and is currently the second largest single gold producer in Africa. The mine covers a concession area of 434 square kilometers with four main ore types: the quartz vein type, disseminated sulphide type, supergene sulphides and transition ore, and granitoids stock works (visible gold and quartz veinlets). Various mining strategies and methods have been employed for the mining of the narrow-vein ore at Ashanti. In recent years, the mine owner: Ashanti Goldfields Company Ltd. has embarked on a mine-wide expansion program to boost production to a target of one million ounces per annum. With the rapid depletion of its high-grade ore, a suitable mining method was required to produce a high tonnage at low cost to meet production objectives. This paper discusses how the Ashanti mine applied Canada experiences in mining technology to boost production, and the impact that the differing geological settings between the two countries had on the stope performance at the Ashanti operations. Experience developed at the Ashanti mine led to innovative modifications for stope layout and design methods in relatively poor ground conditions.

Oct 1, 2001

By K. G. Baxter, D. G. Dixon

The Sepon process plant utilises an autoclave to oxidize a flotation concentrate containing pyrite, residual copper minerals, and sulphur. The concentrate is produced from the residue of a preceding atmospheric copper leaching circuit. The function of the autoclave is to provide iron and acid for that atmospheric copper leaching circuit. The key issues in the operation of the autoclave are to maximise the production of acid and ferric ions and to avoid scaling issues related to sulphur balling in the autoclave. Scale control in the autoclave was examined using various dispersants and residue recycle without success. Operation of the autoclave at high temperature and high acidity addressed the scale issue through rapid oxidation of the sulphur and produced a ferric sulphate precipitate in the residue that could be re-leached to provide ferric iron. This paper presents the development steps followed, through batch and continuous piloting that resulted in an autoclave circuit design that addressed the above process requirements. Following definition of the process design basis, modelling of the autoclave operation was carried out to assist with engineering design. The model included thermodynamics and kinetics of oxidation of pyrite, elemental sulphur and covellite and also considered gas/liquid mixing, oxygen solubility as a function of temperature and solution composition, ferrous to ferric oxidation, gangue reactions with acid and precipitation/re-dissolution of basic ferric sulphate and alunite.

Jan 1, 2004

By S. Nikolic, O. O. Kehinde-Philllps, O. T. Djamgouz, D. H. Rousell

"A bulk mining method is employed at the Lockerby mine resulting in the formation of large muck-piles. If these muckpiles remain in the stopes for some time they may agglomerate to the extent that the muck cannot be removed by a scooptram. A laboratory investigation was undertaken with sulphide material from the mine in order to detemine the time that oxidation begins and the flowability of the material as a f unction of several factors. The laboratory results are applied to the conditions in the muck-piles.The time of the beginning of oxidation of the material decreases as the sulphide composition, water content and availability of air increases. Oxidation is retarded by the addition of a copper sulphate solution instead of water. The unconfined yield force (strength} of the material increases with an increase in the sulphide composition, water content and time. The material ceases to be free-flowing before there is visible evidence of oxidation and this suggests that oxidation actually begins earlier and that agglomeration is also due to the capillary action of water.Broken ore should be removed from the stope prior to the time a muck-pile ceases to be free -flowing-perhaps as early as two days f or high-grade ore and 5 days f or low-grade ore. In order to control dust, 1.4 weight per cent of a 5 per cent solution of copper sulphate should be added 10 the muck-pile rather than water. This inhibits oxidation and increases the time that a muck-pile remains free-flowing."

Jan 1, 1984

By Frank B. Amon

Highland Valley Copper had to make some significant changes in the way it was working in order to counter the effects of ever-increasing costs and decreasing metal prices. A mine/mill optimization plan started in 1997 introduced new technologies and management approaches that resulted in a dramatic drop in cash breakeven costs. The changes involved employee training, added authority and responsibility for staff, better communications, and a consistent approach to setting and achieving property-wide goals. The net effect was to change the culture of the organization from one that was fragmented and focussed on local objectives to one that is cohesive and has common goals. These changes have allowed the mine to remain in business during a protracted period of low metal prices, and have positioned the mine favourably to benefit even more from any future increase in prices.

May 1, 2004

By Manjeet Chowdhry, Qingxia Liu, Phillip Choi, Zhenghe Xu

Computational chemistry methods, such as density functional theory (DFT), are powerful tools to quantify reagent-mineral interactions encountered in sulphide mineral flotation. A quantitative relationship between theoretically calculated parameters based on chemical structure of collectors and their reactivity with different metals/minerals can provide valuable insights for design and development of more powerful and tailor-made reagents offering enhanced metal/mineral selectivity. DFT calculations at B3LYP/6-311++G(3df,3pd) level were employed to elucidate the reactivity of neutral sulphide collector reagents, including thionocarbamates (TC), thioureas (TU), xanthogen-formates (XF), dialkyldithiocarbamates (DTC) and dialkyltrithiocarbonates (TTC) with different heavy metal ions (Cu2+, Zn2+ and Pb2+) in solution. The extent of delocalization of lone pair electrons of heteroatoms (attached directly to C in C=S) over C=S group was found to be the dominant factor in determining the collector’s reactivity. Order of reactivity was established as: TU > TC > XF > DTC > TTC. All the collectors showed superior affinity towards copper followed by lead. Unidentate binding was observed through sulphur atom except for xanthogen-formate for which bidentate binding mode was observed. Effect of nature of substituent groups at N and/or O atom on reactivity of thionocarbamate and thiourea was also investigated. The results obtained through DFT calculations are consistent with the experimental data reported in literature.

Jan 1, 2015

By M. J. Fairweather, Keith Lee, Naseem Mian

"The initial metallurgical response of the lead flotation circuit at Cominco Alaska's Red Dog Mine was substantially below feasibility expectations. A program of diagnostic mineralogical analysis pointed the way to a number of process improvements, including simplification of the flow sheet and installation of a large flotation column as a lead cleaner. A diagnostic mineralogical analysis of the improved circuit shows that inadvertent activation of both sphalerite and pyrite has been substantially reduced, resulting in significant improvements in metallurgical performance. Directions for further improvements to the circuit performance are suggested by the recent analysis.IntroductionRed Dog is a high-grade, sedimentary exhalative (sedex) deposit with relatively simple mineralogy. The primary non-sulphide gangue minerals are quartz and barite, with minor barium carbonate (witherite). The iron sulphate minerals, siderotil, rosenite and copiapite occur variably throughout the deposit. Mineral texture is variable ranging from liberated sphalerite grains visible to the naked eye to intergrowths, particularly between sphalerite and galena, to less than ten microns. Both pyrite and marcasite are present. To date no enhanced reactivity of marcasite has been observed. For this discussion, ""pyrite"" will be used to refer to both iron sulphide minerals. In common with other sedex deposits, Red Dog contains organic and sulphur impurities."

Jan 1, 1997

By G. Warren

"In the past, smelting and refining of the precious metals recovered from ore has been generally looked upon as a small and relatively minor component of the business of gold mining. This is not surprising when one considers that the manpower, space and capital components of a gold refinery at an operating mine can be several orders of magnitude smaller than other unit operations at the same location. This philosophy is changing however, as economic and environmental pressure are forcing a re-evaluation of all aspects of gold mining and milling.This paper describes and evaluates three furnace technologies available and used by precious metal operators. The operation of arc, induction, and reverberatory furnaces are discussed and their strengths and weaknesses with respect to capital cost, impurity removal, slag quality, and environmental concerns highlighted.INTRODUCTIONIn the past, smelting and refining of precious metals recovered from ore has been generally looked upon as a small and relatively minor component of the business of gold mining. This is not surprising when one considers that the manpower, space, and capital components of a gold refinery at an operating mine can be several orders of magnitude smaller than other unit operations at the same location. Generally, gold producers will spend a great deal of effort to squeeze the last drop of efficiency out of a leach or grinding circuit via simulation or testwork but will design and build the refinery based upon past practices or industry standards. That past practices or industry standards will provide a functional refinery is undisputed; that this philosophy achieves the efficiencies that are possible or demanded in other plant operations is debatable.Environmental and worker hygiene requirements are considerations as well. Pollution control equipment can become a substantial contributor to both the capital and operating costs of a refinery and furnace selection has a marked influence upon the type and cost of this equipment. Slag characteristics and subsequent processing options available also play a role in furnace selection as precious metal slag losses and the recovery effort can greatly influence the cost / benefit analysis of a particular technology."

Jan 1, 2001

By A. Quilodran, B. Jakovljevic, T. McCallum, P. Wong

"Rare earth separation by solvent extraction (SX) requires multiple separation plants each consisting of many extract, scrub, and strip stages to separate the individual metals. SX modeling advances have brought benefits to circuit design and process optimization by quickly narrowing test conditions without the need for exhaustive laboratory studies. Modeling can be used to optimize circuit configuration, O/A ratios, and acidities, which allows for CAPEX and OPEX savings. A comparison between pilot plant data and the results expected from modeling is presented for rare earth separations with CYANEX® 572.INTRODUCTIONRare earth separations can be difficult due to limited separation between the elements (Xie, Zhang, Dreisinger, & Doyle, 2014). This requires relatively complex solvent extraction circuits utilizing multiple extract, scrub, and strip stages as well as multiple SX configurations to achieve the desired metal purities. Designing rare earth circuits can be complex, and significant time and testing may be necessary to determine the required staging and optimal conditions.Circuit modeling for rare earth separations has been introduced to the industry using CYANEX® 572 extractant (Soderstrom, McCallum, Jakovljevic, & Quilodran, 2014). CYANEX® 572 is an acidic organophosphorus extractant formulation which has a weaker ligand-metal complex strength than that of the traditionally used phosphonic acid extractants. This allows efficient extraction while requiring a significantly lower acid concentration for stripping (Wang, Li, Zhao, Dong, & Sun, 2015). The reduced acid requirement in strip is expected to provide OPEX savings.The modeling can be utilized to quickly determine the required acidity and organic/aqueous (O/A) ratio for a given separation. It is also expected to reduce CAPEX requirements as optimal staging can be determined, and implemented.CYANEX® 572, combined with modeling, was utilized to produce a purified dysprosium (Dy) stream. To achieve this separation, multiple SX circuits were designed and operational conditions specified to separate Dy from the mixed rare earth chloride feed."

Jan 1, 2016

By E. Wasmund

"Sandfire’s DeGrussa Copper-Gold operation in West Australia is a new high grade copper sulfide mine, which includes a 1.5 Mtpa concentrator which was completed in 2013.Early after commissioning, it was identified that the flotation capacity in the all-mechanical cleaner circuit was not sufficient. In order to improve recovery, the tail from the cleaner scavenger was sent back to feed the rougher scavengers. Test-work was done on-site to evaluate the possibility of using a flotation column as a pre-cleaner. A CavTube™ sparging system was selected, which is especially effective for fine ore particle flotation. Test-work was conducted at site using a 150 mm diameter unit, and then confirmed on a 500 mm diameter unit. A 4250 mm diameter full scale unit was installed in Q4 2014 and commissioned in Q1 2015. This unit gave some significant advantages including a reduction in re-grinding requirements, elimination of a circulating load and increase in the recovery of copper in the cleaner circuit and overall circuit.In this presentation, the benefits of columns and cavitation sparging for floating fine particles and rejecting fine entrained gangue will be explained. Also, the results from a lab unit and a pilot unit will be compared against the results of the full-scale unit. The paper will demonstrate the scalability of flotation columns, and which phenomena and scale-up criteria must be considered to be successful. Finally, some general observations will be made about the importance of columns in copper cleaning circuits.IntroductionSandfire Resources’ DeGrussa copper-gold concentrator is located approximately 900 km north-north-east of Perth in Western Australia. The project area landscape is scrubby mulga lands with few notable features. The climate is arid with high temperature and heavy summer downpours."

Jan 1, 2016

By Rob Boom, Yasuyuki Tozaki, Frank M. Wheeler

Selection of a suitable site for a metallurgical plant is crucial for the success of the business case. For a brownfield project, with the decision to locate the project on a site with existing production facilities and activities, the selection of the site has been made. For a greenfield project, important economic and logistical considerations include proximity to primary and secondary resources and/or to the market, infrastructure, and access to energy and water. National and regional aspects, including the social license to operate, can be decisive in final site selection. Key to recruiting and retaining a labour force are proximity to urban areas, along with weather and health conditions at the site. Risk factors include site geotechnical parameters and topography, contamination, as well as probability and types of potential natural disasters.

Jan 1, 2015

By Dave Bulled, Jim Thompson, Tim Leriche, Mark Blake, Troy Wilkie

"A commitment to a core testing, plant modeling and reconciling technique has shown substantial economic benefits to IOC in terms of accurate production forecasting, smoother operation of the mill, improved expectations of throughput and co-operation across production departments from geology, planning, mining, and processing, to shipping of concentrate to market.This paper describes a successful seven year program of forecasting throughput of the autogenous milling circuit at the Carol Lake concentrator of IOC. Work started with audits of the grinding circuit in 2001 and benchmarking of the data collected from samples of mill feed and plant operation to the CEET mill design and throughput forecasting model.Initially 390 drill core samples were tested for SAG Power Index (SPI) to measure the energy required in milling, and the data distributed using a geostatistical technique across the two operating pits, so that hardness was estimated in each of the 40,000 blocks (or 1500 million tons) of potential ore. In 2004 a forecast of energy requirement, i.e. forecast of throughput for a given power availability at the mill, was produced for each ore block using the CEET model and used for mine planning to smooth plant throughput. The forecast for blocks mined on a monthly basis was reconciled with plant results over the next 2 years and minor changes made to the CEET model. The forecasting exercise was repeated in 2006 and in 2008 with the latest model based on the testing of almost 1300 samples of drill core at closer spacing.INTRODUCTIONThe contracting of sales to clients and the timely supply of products to meet those contracts is a cornerstone of good business practice. Ensuring the correct scheduling of production is a major concern of mining companies where the supply and qualities of the raw material is uncertain and production facilities are not flexible. This is particularly challenging when the product is of high volume and produced far from the customer, such as iron ore.Apart from the metal content of the ore being mined, the greatest impact on production scheduling is the throughput of the comminution section of the extraction plant; most notably when size reduction is achieved by autogenous grinding. The response of the mills to variability in the hardness of the ore can change throughput by as much as 50% from day to day at some plants."

Jan 1, 2009

By C. Velásquez, W. Bergholz, C. Spence, P. Lind

NuevaUnión SpA (NuevaUnión) is a development project located in the Huasco province of the Atacama region of Chile. It is held in a joint venture company owned 50:50 by Teck Resources Limited (Teck) and Newmont Goldcorp. It includes the Cu-Mo Relincho deposit and the Cu-Au La Fortuna deposit, with plans to utilise a single concentrator to be built at the Relincho site. The Relincho site is at an altitude of 2,000 masl and is 40 km from the La Fortuna site which is at an altitude of 4,100 masl. The project is currently completing a Feasibility Study and is reviewing equipment selection and flowsheet options. This paper is based on the current thinking, and design decisions will be finalized at the completion of the Feasibility Study. NuevaUnión is currently planning for phased operation, processing Relincho ore at 104 ktpd followed by processing ore from La Fortuna at 116 ktpd. Plans for the third phase include doubling the main processing lines and returning to Relincho ore at a processing rate of 208 ktpd. The NuevaUnión concentrator will incorporate comminution and flotation circuits that are being designed to maximize the overall economic value of the combined ore deposits. Major ore characteristics differ between the two ore bodies, such as ore competency, grindability, liberation grind size, pulp rheology, tailings properties, minerals and metals of value, as well as gangue mineralogy. Mineral processing choices have been made to optimise value from each deposit and the combined project. INTRODUCTION Between 2010 and 2013, two significant mining projects were being developed in Chile: Goldcorp’s El Morro project had recently finalized a Feasibility Study and, in 2011, had received its environmental approval for construction; and Teck Resources Limited’s (Teck) Relincho project was finalizing a Feasibility Study and preparing its Environmental Impact Study. Both projects were: Geographically close, at only 40 km apart. Considering similar infrastructure. Each was planning to have its own concentrator, tailings management facility, high voltage power line, port, concentrate transport system, seawater desalination plant and pumping system to mine site.

Jan 1, 2019

By Hannu J. Häkkinen

Metal clusters exhibit unique size-dependent physical and chemical properties that differ from those of bulk materials or large particles. Here we discuss recent theoretical investigations of the catalytic properties of free and MgO-supported gold clusters. The catalytic activity of gold clusters depends sensitively on the environment, charge state, and chemical composition of the catalyst. Relativistic bonding effects stabilize large planar structures for gas-phase gold clusters, and non-compact ?quasiplanar? structures are present as important isomers also for surface-supported clusters. The hybridization of the atomic 5d and 6s states is significantly enhanced by the relativistic effects, and large spatial variations in the nature of the local electronic structure make the low-coordinated gold atoms preferable adsorption sites for oxygen molecules. The adsorbed oxygen molecules are activated to superoxo- and peroxo-states via charge-transfer from gold, and Eley-Rideal and Langmuir-Hinshelwood reactions with CO proceed via low-barrier formation of intermediates, which do not require O-O dissociation as precursors. This facilitates the low-temperature (below 300 K) activity of gold nanocatalysts in CO oxidation. Other gold nanostructures, such as mono-atomic gold nanowires, may also become important prototype systems in chemical sensing and nanocatalysis; here we show that they are active promoters of hydrogen dissociation.

Oct 1, 2003

By Frank Mucciardi, Zhongsen Yuan

A new heat transfer technology --- termed Thermopump technology has been developed. This technology originates from conventional heat pipe configurations but has now evolved into its own class of heat transfer units, which we refer to as `Thermopumps (TP)'. A key feature is that Thermopump technology can be applied to high temperature / high heat flux environments where conventional heat pipe technology fails. Moreover, when implemented in less demanding applications where heat pipes appear to operate, Thermopump units have been found to function more smoothly and reliably. This paper will introduce Thermopump technology and several applications of this technology in steelmaking and refining will also be discussed. In addition, this paper will focus on three classes of applications: 1) waterless, non-consumable, high efficiency Thermopump oxygen lance and/or burner for EAF's, 2) Thermopump ladle lance for the desulfurization process, and 3) Thermopump cooling panels for furnace walls and roofs. Facilities equipped with Thermopump technology are expected to he better than the current corresponding ones in terms of increasing productivity and energy efficiency while at the same time lowering operating costs.

Jan 1, 2004

By Dennis Hoffmann

"Abstract - Banded iron formation rocks associated with massive sulfide lenses in the Broken Hill Pb-Zn-Cu-Ag deposit in the Namaqualand Metamorphic Complex, South Africa , were investigated with respect to the geochemistry of manganiferous silicate-rich bands. Two common varieties of these are: amphibole- and garnet-rich iron formation bands. The results reveal that the former are enriched in Fe, Mg, Cu, Co and S. The garnet-rich bands are enriched in Mn, Ca, P, Pb and Ba with significant detrital contamination of Ti, Al, Zr, Cr, Y, V, Ni and Nd.The silicate-rich bands have compositions, in terms of, Si/Al, Si/Fe, Fe/Mn, La/Ce and Co/Zn, comparable to submarine chemical sediments which precipitated from hydrothermal fluids. The garnet­ and amphibole-rich bands are interpreted as ""evolved"" and ""immature"" hydrothermal sediments, respectively. The latter resulted from rapid precipitation after exhalation, whereas the former had a longer residence within sea water. The silicate-rich bands both exhibit increasing Mn/(Mn+ Fe) fractions, which are consistent with a variation expected from proximal to distal depositional settings. The prevalence of garnet-rich bands over amphibole-rich bands is interpreted as the result of injection of hydrothermal fluids from a single vent situated along the northwest margin of the Broken Hill deposit."

Jan 1, 1994

By L. O. Thomas

THE Alaska Highway, in its course through British Columbia, traverses parts of two great physiographic divisions of Canada which are also distinctive geologically-the Cordillera in the western section and the Interior Plains in the eastern. The Cordilleran region in the portion of the Province with which this paper deals can be divided into four major northwest systems, known respectively from west to east as Coastal, Plateau, Cassiar-Omineca, and Rocky Mountains. The Coastal system consists solely of the Coast range except in the extreme northwest, where a part of the St. Elias range is included. The Coast range, characterized by mountains of great ruggedness,. is made up of an igneous complex of granitic rocks intruded chiefly as a great batholith. In places, spurs of these rocks extend into the Plateau heft, a partly mountainous tract largely occupied by quartzites, quartzose mica schists and their gneissic phases, and crystalline limestone with interbands and broad areas of chlorite, _hornblende, and sericite schists and bodies of intrusive granite gneiss-an assemblage of rocks known as the Yukon group. The Cassiar-Omineca system marks the divide between the Pacific and Arctic drainages. Its eastern boundary is well defined in the south by the Rocky Mountain Trench (see p. 229). The rocks of the system are, miainly, highly altered Palaeozoic sediments, but there are also Precambrian and Mesozoic rocks, the latter largely volcanic. The core of the system is granitic and there is evidence (see p. 221) to support the belief that it is of such a length as to constitute a batholith comparable to that of the Coastal system.

Jan 1, 1944