Search Documents

By H. B. Farnam

"THE IRON ORE Company of Canada has been using do-it-yourself type explosives for three years. During the last 12 months we have used over 10 million pounds of ammonium nitrate-fuel oil explosives and either purchased or formulated one million pounds of slurried explosives.W e have been moving approximately one million cubic yards of stripping and ore per month and we expect our production rate to in-crease. Eighty per cent of our strip-ping and ore is soft enough to be blasted successfully with ammonium nitrate-fuel oil mixtures. Twenty per cent of our material is extremely hard and requires an explosive having greater strength than an AN-fuel oil mixture.W e had been using canned am-monium nitrate base explosives and TNT pellets to give maximum bottom loading density to fracture hard rock. As AN -fuel oil became widely used, it was apparent that other types of explosives could be formulated to fit our blasting requirements. Dr. M. A. Cook of the University of Utah was consulted regarding new explosives and together we developed the blasting slurries.Figure 1 shows a general view of one of our hard rock pits. The foot wall is on the right-hand side and this material is called iron forma-Figure 1.-General view of hard rock pitstion by our Company but is called 'Taconite by the operators on the Mesabi Range. This material runs 35 to 45 per cent iron and many pieces are hard enough to scratch glass. The formation is tilted at an angle of 55 degrees as can be seen in Figure 3.The bedding planes of this rock are about 24 to 36 inches apart and if the material is not well broken or fragmented, large chunks or slabs must be handled by the shovels which reduces shovel capacity and efficiency and increases maintenance costs."

Jan 1, 1960

By P. Lind, A. Gagnon

"Goldcorp has embarked upon an ambitious, industry-leading, multi-year water use reduction effort. This is a proactive, voluntary effort that reflects our commitment to truly sustainable mining. This effort will focus on increasing water re-use and recycling, and reducing water inputs ultimately towards zero. All of our operating mines are expected to contribute to this effort and are currently in the process of developing plans to meet short and long term objectives. One of the largest needle movers to increase water re-use and recycling is in the area of tailings management. Within five to ten years at Goldcorp, it is envisioned that the need for wet tailings dams will be eliminated and that all new tailings facilities will consist of only filtered or dewatered tailings. Filtered tailings is developing into a mature technology with wide application in mine waste management. This paper describes a conceptual level evaluation on the transition from a slurry to a filtered tailings operation at the Cerro Negro mine in southern Argentina. Key benefits and challenges are highlighted.INTRODUCTION Goldcorp’s Cerro Negro operation is located in the Santa Cruz province in the Patagonian region of Argentina. Cerro Negro has been in operation since 2014 and commercial production was achieved on January 1, 2015. The processing capacity of the plant is 4,000 tonnes of ore per day and in 2016 produced 363,000 ounces of gold and 3.1 million ounces of silver (Goldcorp Inc., 2017). As the mine is located in a semi-arid area, it is important to evaluate technologies that could reduce freshwater consumption and maximize water re-use and recycle rates. The current tailings operation at Cerro Negro incorporates pumping of tailings slurry into a conventionally lined Tailings Storage Facility (TSF). Water is reclaimed from the tailings supernatant pond to the process plant via pumps, however, water losses occur due to evaporation and solution retention within the slurry tailings voids. Converting to a filtered or dewatered tailings operation would allow for increased water recovery prior to tailings disposal, and decreased water losses from evaporation and from retention in the tailings solids void space. This paper describes a conceptual level evaluation on the transition to filtered or dewatered tailings with the primary objective of moving closer Towards Zero Water."

Jan 1, 2017

By V. N. Mackiw, H. Veltman

"A process is described which permits the separate recovery of lead and zinc from complex low-grade sulphide concentrates such as are produced from the New Brunswick type of disseminated pyrite ores. This process calls for the preparation of a lead-zinc bulk concentrate from the original ore by flotation. The bulk concentrate is then oxidized under pressure in autoclaves in aqueous sulphuric acid solution, such as return electrolyte from zinc electrolysis. This yields a zinc sulphate solution and a residue containing lead sulphate, unaltered pyrite and elemental sulphur generated during the oxidation. After the oxidation, the leach slurry is briefly heated to above the melting point of elemental sulphur and then cooled. Thus, pellets containing pyrite and elemental sulphur are formed, and they are separated from the lead sulphate by screening and/or flotation. Laboratory tests have shown that about 95 per cent of the zinc and lead can be separately recovered from complex bulk concentrates. Process possibilities are discussed."

Jan 1, 1967

By Jing Li, Weiqiang Lai, Joe Zhou, Jiezhen Ma, Shuibo Chen, Ashele Copper Company, Feng Gao, Guofu Feng

"Copper-zinc ores often contain gold and silver, which can be recovered into copper concentrate by flotation as by-product. The challenges for operations that produce copper, zinc, gold and silver are the separation of copper and zinc and the low grade of precious metals. Ashele copper-zinc ore in north China contains 2.38% Cu, 0.69% Zn, 0.21 g/t Au and 18.10 g/t Ag and the plant produces copper and zinc concentrates, with gold and silver being recovered into copper concentrate. Copper occurs mainly as chalcopyrite and Zn occurs as sphalerite. Copper is well recovered with a recovery of over 94%. However, the recovery of Zn is substantially low (around 50%) due to fine grain size of sphalerite. In addition, gold recovery is much lower than expected and only 33% of gold in the flotation feed was recovered. The grade of gold in copper concentrate is also lower than the required payable grade (1.0 g/t). To determine the cause for lower Zn and Au recoveries, a plant survey program was conducted on the operation. The information acquired shows that the loss of Zn was mainly in the copper concentrates (accounting for approximately 38% of the head assay); of which, 24% was liberated, 8.5% was associated with chalcopyrite and 4.6% was associated with pyrite, indicating that the separation of copper and zinc was the main cause for the Zn loss, with liberation being the second cause for Zn loss. Future effort in improving Zn recovery should be focused on the separation of zinc from copper. Gold in the ore occurs as both microscopic gold and submicroscopic gold, accounting for 36% and 64% of the head assay, respectively. Microscopic gold occurs mainly as native gold and electrum; it is relatively coarse with a grain size of 10 to 240 µm and a large portion can be recovered by gravity. Submicroscopic gold was mainly carried by pyrite (accounting for 38%), and to a less extent, by tennantite (15%) and chalcopyrite (10%). Gold in sphalerite is nominal (1%). It is suggested that more coarse gold and tennantite be recovered and a gold recovery increase can then be achieved to obtain a copper concentrate with over 1.0 g/t Au through flowsheet optimization. Gravity concentration should be investigated and may be worth added into the existing flowsheet to maximum the gold recovery and grade.INTRODUCTIONCopper-zinc ores containing gold and silver is a subtype of polymetallic sulphide ores. Unlike porphyry copper sulphide ores and iron-oxide copper-gold ores, this type of ores often contains substantial amounts of zinc and lead. Polymetallic sulphide ores are mainly distributed in Canada, such as at the LaRonde and Horne deposits. Other examples include Mt. Morgan in Australia and Boliden in Sweden. Globally, production and reserves from gold-rich VMS deposits account for 1370 t gold. This is equivalent to 1% of the world production and reserves, whereas the Canadian total for gold-rich VMS deposits is 870 t, representing close to 10 % of Canadian production and reserves (Gosselin & Dube, 2005a, 2005b). Flotation is the principal process for processing the copper-zinc sulphides ores, for subsequent smelting, roasting, or hydrometallurgical treatment. Oxidized copper-zinc ores can also be processed using leaching technology. For example, at LaRonde operation (a Cu-Zn-Pb ore containing 3-4 g/t Au and 60-100 g/t Ag) the flowsheet consists mainly of a copper flotation circuit and a zinc flotation circuit followed by a cyanidation process of flotation tails. The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation (Zhou et al., 2005)."

Jan 1, 2016

By C. J. Newman, R. J. St. Eloi, G. Macfarlane

"The Kidd Creek copper smelter has been expanded from its original design of59000 tonnes of copper per year to over 120 000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and, generally, to optimize the operation.The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates. IntroductionThe Kidd Creek Division of Falconbridge Limited is a base-metal mining and metallurgical complex located in Timmins, Ontario. The discovery of the original copper-zinc-silver orebody was announced in April 1964. Mining operations began in 1966 with a 9000 tonnes per day (t/d) concentrator corning on stream in November of that year. In April 1972, a 108 000 tonnes per year zinc plant was conunissioned. Over the years the facilities have been expanded, such that the concentrator now has the capacity to process 13 000 t/d of ore. To expand zinc production, the world's second installation of the Commco/Sherritt pressure leaching facility was completed in 1983 to bring total zinc production capacity to 136 000 tonnes per year. In 1973, serious planning for a smelter operation began. In early 1975, after studying both continuous smelting and flash smelting processes, a decision was made to proceed with the technology offered by Mitsubishi Metal Corporation of Japan. The Mitsubishi Continuous Smelting Process was to be used for the smelter and the Onahama No. 3 tankhouse technology for the copper refinery."

Jan 1, 1994

By P. K. Kaiser, C. D. Martin, F. Amann

"This article focuses on the uniaxial compressive strength (UCS) of homogeneous and heterogeneous rocks. Critical factors impacting the UCS of rocks are reviewed and then separate assessments of UCS data from homogeneous and heterogeneous rocks are presented. The variability (coefficient of variation) of UCS test results for homogeneous rocks is found to be generally <25% while for heterogeneous rocks the variability is >35%. Failure mode variation is found to be the cause of the variability of UCS test results in heterogeneous rocks. Empirical engineering design methods that use UCS as an input parameter are discussed and suggestions are provided for selecting appropriate UCS values.INTRODUCTIONThe UCS is one of the most commonly used rock engineering parameters whether for rock mass classification or for strength determination. The mean UCS and its variability are often assumed to represent a reliable rock material property. For the reasons discussed in this article, UCS is rarely representative of the intact rock UCS. The UCS test simply records the collapse load during uniaxial loading of a cylindrical specimen. As suggested by many, the UCS is an index rather than a unique engineering parameter. The UCS is thus a proxy for rock strength which depends on the loading rate (e.g., Bieniawski 1967), specimen geometry (e.g., Hudson et al., 1971), specimen size (e.g., Bieniawski 1968), and many other factors. Furthermore, the UCS is not the same as the Hoek-Brown strength criterion parameter sci.There are differences in opinion on what is commonly considered to be ‘intact rock’. When sampling ‘intact’ pieces of core from drillholes crossing blocks of rock bound by block forming discontinuities, samples will be ‘intact’ but some samples will be veined, others will be damaged, and others will be neither. According to Hoek (1983), intact rock pieces are “the unfractured blocks occurring between structural discontinuities in a typical rock mass” and the sci parameter for intact rock is determined using the fitting procedure proposed by Hoek and Brown (1997) based on the data requirements outlined by Hoek (1983). Studies (e.g., Bewick and Kaiser 2014; Kaiser and Kim 2014) have shown that independently determined UCS and sci values for the same rock type are not equivalent. Thus, UCS data cannot be used as a replacement for sci."

Jan 1, 2015

By D. A. Ainsworth

"The first known use of activated carbon dates back to the Ancient Egyptians who utilized its adsorbent properties for purifying oils and medicinal purposes. Centuries later, the early ocean going vessels stored drinking water in wooden barrels, the inside of which had been charred. (However, by modern definition the carbon used in these applications could not truly be described as activated.) By the early 19th century, both wood and bone charcoal was in large scale use for the decolorization and purification of cane sugar.However, it was not until the beginning of the First World War that the potential of activated carbon was really capitalized upon. The advent of gas warfare necessitated the development of suitable respiratory devices for personnel protection. Granular activated carbon was used to this end as, indeed, it still is today.By the late 1930's there was considerable industrial scale use of carbon for both gaseous and liquid phase application and new manufacturing processes had been developed to satisfy the needs of industry. During the 1939-1945 war, a further significant development took place - the production of more sophisticated chemically impregnated carbon for the removal of both war and nerve gases."

Jan 1, 1984

By C. Hudson, D. Tremblay, A. Frey

"A discussion of the design, challenges and successes associated with the commissioning of the gravity recovery circuit at Canada’s newest open pit gold mine - Atlantic Gold’s Moose River Consolidated Project in Nova Scotia, Canada is presented. An overview of the project, its historical significance and overall flowsheet is provided with special focus given to the design and selection of the gravity circuit equipment including the scalping screen, gravity concentrators and the novel intensive leaching technology selected for the project. The performance of the gravity circuit is benchmarked against the feasibility study process design specifications and the outcomes are discussed. Challenges encountered during commissioning are also presented, including the use of third-party automation and the effects of screen sizing on overall gravity circuit performance. Mechanical modifications made to the Sepro Leach Reactor for the Moose River project are also discussed. A detailed technical review of the mechanical and operational aspects of the Sepro Leach Reactor is provided with key operational data on leach times, recoveries, reagent usage, solid-liquid separation, pregnant solution quality and its influence on bullion purity.INTRODUCTION Atlantic Gold Corporation’s Moose River Touquoy Mill in Nova Scotia, Canada was commissioned in the fourth quarter of 2017 with commercial production declared in March of 2018. The 2 Mtpa process plant uses a conventional, gravity-CIL process. This site was previously mined in the 1870s. Interest waned in the early 1900s but resumed in the 1930s and the mine was brought back into production in 1935 until an underground mine collapse in 1936. This mining district became famous after CRBC radio commenced a ground breaking, around the clock, broadcast of the rescue operations. Over 100 million people listened to the broadcast from Canada, the United States and the United Kingdom. These broadcasts changed radio, transforming it from a medium for music to on the spot, breaking news reporting. The mill was constructed by Ausenco on a fixed price EPC contract in the historic Moose River gold mining district, 95 km north-east of Halifax by road. The mill will process ore from the adjacent Touquoy pit for the first 5+ years of operation; after the Touquoy reserves are exhausted, the mill will process ore trucked 37 km from the Beaver Dam deposit for an additional 5 years."

Jan 1, 2019

By T. G. Joseph

"The Oil sands-Equipment Interactions Program (OsEIP) is a collaborative research venture between Syncrude Canada Ltd., James Progithin International Ltd. (JPi), the University of Alberta, P&H MinePro, and Caterpillar Inc. The objective is to better understand the behaviour of oil sands as it interacts with mining equipment, in particular, large trucks and shovels. With a move to ever larger equipment, mining oil sands of highly variable bitumen content, ground stability comes into question. This paper outlines this aspect of OsEIP and provides some insight into how some of the findings enable an improved understanding of oil sands behaviour that may impact large equipment design, operational and maintenance strategies. IntroductionThe mechanical behaviour of oil sands in the underfoot and in the face yields some of the harshest stability and digging conditions of any mining environment. High maintenance costs from truck and shovel fatigue failures predominate as a result of ground stability issues. Wear rates of shovel and dozer ground engaging tools (GET), rollers, roller paths and crusher screens result in costly and frequent replacement, or even more frequent and costly sacrificial wear zone building. From the shovel face to the crushers and screens, dry oil sands mechanics affects the degree of fragmentation and, ultimately, bitumen production.An increased knowledge of the behaviour of oil sands with respect to stability, fragmentation and abrasion, etc. would enhance the long-term equipment design process at the vendor level, and provide the end user with improved short-term operational guidelines and long-term strategies for future purchases and operation. Truck vendors recognize that the interaction between operator, seat, frame, suspension, tires and oil sands is unclear, and must be better understood before proceeding to next generation designs. Similarly for shovel manufacturers, the relationship between bucket/dipper motion, carbody, side frame, rollers, track and oil sands follow in the same vein."

Jan 1, 2002

By N. Wachgama, J. P. T. Kapusta, R. U. Pagador

The Thai Copper Industries smelter (Thai Copper) is located some 200 km southeast of Bangkok near the MapTaPhut deep sea port in one of the industrial centres of Thailand. Although construction of the complex started in the mid 1990s, the smelter, acid plant and refinery were completed in 2004. Thai Copper is a state-of-the-art copper smelter processing imported concentrates with a total yearly capacity of 165,000 tonnes of cathodes. It employs the El Teniente Technology where concentrates are blended and smelted continuously in a primary smelting reactor to produce high grade matte or white metal. The white metal is converted in batches to blister copper in Hoboken siphon converters equipped with Air Liquide Shrouded Injector (ALS I) Technology for sonic injection of oxygen enriched air. Final refining is carried out in two anode furnaces prior to anode casting and electrorefining. Thai Copper and Air Liquide Canada executed a technical assistance agreement in late 2005. Pre-commissioning of the shrouded injectors took place in July and November 2006 while hot commissioning occurred in December 2006. This paper presents the major technical aspects of the joint commissioning, including the establishment of operating practices specific to shrouded injection converting. Preliminary results of this first commercial implementation of ALSI Technology in copper converting are also provided.

Jan 1, 2007

By A. Esterhuizen, S. Essack, H. Joubert, N. Fowler

Tenova Pyromet has developed innovative technologies for copper smelting and electric slag cleaning furnaces. Based on client feedback and requirements, innovative designs have been developed to address key design areas and improve furnace reliability, operability and hygiene. These developments include the NovaLance™ lance system to prevent lance bending on top submerged lance furnaces, the SlagFlo™ slag tapping flow control device to better control bath levels and tapping rate for granulation, and an electrode seal for improved sealing directly onto the electrode casing to allow water-cooled electrode components to be located above the furnace roof. The potential application and benefits of these innovative designs are discussed. INTRODUCTION Tenova Pyromet has a long history in the engineering and supply of innovative electric furnace and related equipment for the base metals and platinum industries. Recently Tenova Pyromet has used its furnace equipment design experience to engineer innovative solutions for top submerged lance (TSL) furnaces, and potentially other furnace technologies. These equipment design solutions are developed to address specific operating challenges and operator requirements. Three of these innovative equipment developments are discussed in this paper. First the NovaLance™ lance technology to prevent lance bending during operation in TSL furnaces, such as used for primary copper smelting, is described. Lance bending has been identified as a significant problem for TSL furnace operators as it causes down time and affects furnace availability. The SlagFlo™ device to control the slag flow rate during tapping has been developed based on specific requirements in the mineral wool industry. The SlagFlo™ device can be used to control slag bath levels in primary smelting, converting and slag cleaning furnaces for base metals including copper. In addition, it can be remotely activated for the safe closing of slag tapholes located upstream from a water granulation system. Finally, Tenova Pyromet developed an electrode seal that seals directly onto an electrode surface. This is a special requirement related to base metals and platinum electric smelting and slag cleaning furnaces where furnace operators prefer to keep the water-cooled electrode equipment above the furnace roof. The seal can be used to seal directly onto the potentially hot and uneven surface of Söderberg, pre-baked and graphite electrodes.

Jan 1, 2019

By Frederick W. Breaks, Andrew G. Tindle, Julie B. Selway

"Abstract - Rare-element pegmatites may host several economic commodities, such as tantalum (Taoxide minerals), tin (cassiterite), lithium (ceramic-grade spodumene and petalite), and cesium (pollucite). Key geological features that are common to pegmatites in the Superior province of Ontario and Manitoba, Canada, and in other large tantalum deposits worldwide, can be used in exploration.An exploration project for rare-element pegmatites should begin with an examination of a regional geology map. Rare-element pegmatites occur along large regional-scale faults in greenschist and amphibolite facies metamorphic terranes. They are typically hosted by mafic metavolcanic or metasedimentary rocks, and are located near peraluminous granite plutons (A/CNK > 1.0). Once a peraluminous granite pluton has been identified, then the next step is to determine if the pluton is barren or fertile. Fertile granites have elevated rare element contents, Mg/Li ratio < 10, and Nb/Ta ratio < 8. They commonly contain blocky K-feldspar and green muscovite. Key fractionation indicators can be plotted on a map of the fertile granite pluton to determine the fractionation direction: presence of tourmaline, beryl, and ferrocolumbite; Mn content in garnet; Rb content in bulk K-feldspar; and Mg/Li and Nb/Ta ratios in bulk granite samples. Pegmatite dikes with the most economic potential for Li-Cs-Ta deposits occur the greatest distance (up to 10 km) from the parent granite.Metasomatized host rocks are an indication of a nearby rare-element pegmatite. Metasomatic aureoles can be identified by their geochemistry: elevated Li, Rb, Cs, B, and F contents; and by their mineralogy: presence of tourmaline, (Rb, Cs)-enriched biotite, holmquistite, muscovite, and rarely garnet.Once a pegmatite dike has been located, the next step is to assess its potential to contain Ta mineralization. Pegmatites with the highest degree of fractionation (and thus the most economic potential for Li-Cs-Ta) contain blocky K-feldspar with >3,000 ppm Rb, K/Rb < 30, and >100 ppm Cs; and coarsegrained green muscovite with >2,000 ppm Li, >10,000 ppm Rb, >500 ppm Cs, and >65 ppm Ta. Pegmatites with Ta mineralization usually contain Li-rich minerals (e.g., spodumene, petalite, lepidolite, elbaite, amblygonite, and lithiophilite) and may contain Cs-rich minerals (e.g., pollucite, Cs-rich beryl). The ore minerals of Ta are commonly manganotantalite, manganocolumbite, wodginite, and microlite; Ta-rich cassiterite is also commonly present. Tantalum mineralization tends to occur in albitic aplite, mica-rich (lepidolite, cleavelandite ± lepidolite), and spodumene/petalite pegmatite zones."

Jan 1, 2005

"Developed by CRIRSCO, IRT is a document that draws on the best of the CRIRSCO-style reporting standards. These reporting standards are recognised and adopted world-wide for market-related reporting and financial investment.The IRT is not an international reporting code and does not supersede existing national reporting standards. Rather it is a guideline that encapsulates the content of these standards for the benefit of the international mining industry and its various stakeholders.The template is a 'living document' that is continuously updated and improved as new national laws, rules, codes and guidelines are created or amended.The International Template is advisory only and where national codes already exist, these will take precedence. The International Template is intended to assist those countries that either do not have a reporting code or whose code is outdated, to produce a new code consistent with international best practice. It also provides a consolidated version of national codes that reflects their compatible international components and may thus be used in comparisons with other international reporting systems. The word 'Template' is used advisedly to indicate that this document is a model for code development and does not in itself constitute a 'code' which implies that it has legal or other regulatory force.From this point forward, the Template includes words that imply a mandatory action, such as ""requires"", ""applies"", ""must"" etc. This is to enable the Template to be easily adopted by countries and organisations wishing to do so, and does not imply that the Template itself is a mandatory reporting standard.INTRODUCTION2 In this edition of the International Reporting Template (""The Template""), important terms and their definitions are highlighted in bold text. The guidelines are placed after the respective Template clauses using indented italics. They are intended to provide assistance and guidance to readers for interpreting the application of the clauses in the Template.Indented italics are also used for Appendix 1 — 'Generic Terms and Equivalents"", and Table 1 —'Check List of Assessment and Reporting Criteria' to make it clear that they are also part of the guidelines for the application of the Template.Appendix 1 contains a table of generic terms and their equivalents, designed to avoid unnecessary duplication or ambiguity in the textAppendix 2 provides Rules of Conduct for Mineral Resource and Mineral Reserve estimators that may be considered in addition to the Codes of Ethics or Practice normally applying to members of professional institutions."

Jan 1, 2003

By P. Langlois, G. Labonté, J. J. Barrett, J. Holmes

"The Voisey’s Bay mill processes a high-grade pentlandite and chalcopyrite ore in a largely pyrrhotite/troilite matrix. From 1994 to 1997, circuit development focused on making a 14% nickel concentrate. When flowsheet development resumed in 2001, the target grade was raised to 20% ni. initially triethylene tetramine and sulfite pyrrhotite depressants were used in a lime circuit, but by recycling process water and the contained thiosalts, the required nickel grade was made without depressants. construction of the mill was fast-tracked, with start-up in september 2005. ramp-up was faster than other recent nickel installations, with tonnage being limited by concentrate dewatering due to higher-thanexpected ore grades.RÉSUMÉ l’usine de traitement de Voisey’s Bay traite un minerai à teneur élevée en pentlandite et chalcopyrite dans une matrice formée surtout de pyrrhotite/troïlite. De 1994 à 1997, le développement du circuit ciblait la production d’un concentré à 14 % de nickel. lorsque le développement du schéma de traitement a été repris en 2001, la teneur cible a été élevée à 20 % de ni. initialement les déprimants triéthylènetétramine et sulfite de la pyrrhotite étaient utilisés dans un circuit à la chaux; cependant, en recyclant l’eau du procédé et les sulfosels qui y sont contenus, la teneur en nickel a été atteinte sans utilisation de déprimants. la construction de l’usine de traitement a été accélérée et elle a démarré en septembre 2005. la mise en opération a été plus rapide que pour d’autres installations récentes de nickel; le tonnage traité étant limité par le séchage du concentré en raison des teneurs de minerai plus élevées que prévu.INTRODUCTIONnickel was discovered on canada’s east coast in the vicinity of Voisey’s Bay, northern labrador, by chislett and Verbiski (Higgins, 2011) while working for Diamond Fields resources in 1993. The ovoid deposit was subsequently delineated in the winter of 1994–1995. By the end of 1995, the ovoid had been well explored, and at that time was thought to have a reserve of at least 30 million tonnes (Mt), with an average grade of 2.83% ni and 2.0% cu (naldrett, singh, Krstic, & li, 2000). Drilling to the east of the ovoid indicated the presence of significant mineralization. in June 1995, inco limited bought a 25% share in the Voisey’s Bay nickel company (VBnc), which was a subsidiary holding company set up by Diamond Fields. inco also bought 8% of Diamond Fields and negotiated the right to sell all the nickel produced from VBnc for 20 years as part of this agreement. in april 1996, inco bought Diamond Fields and acquired the remaining 75% of VBnc shares."

Jan 1, 2017

By W. E. Lockley

This paper will attempt to answer a number of questions which are important to the safe and continued operation of an electric power system. 1. WHY should electrical protective devices be tested? 2. WHAT devices should be tested ? 3. WHEN should they be tested ? 4. HOW should they be tested? 5. WHO should test them ?

Jan 1, 1977

By S. Kelebek, B. Nanthakumar

ABSTRACT The sensitivity of sulphide minerals towards oxidation depends on the mineralogical makeup and nature of sulphide ores. This paper focuses on chalcopyrite behaviour in a nickel-copper sulphide- ore matrix that was aged in the mine-site stockpiles. Results of collectorless, collector-induced flotation and recovery by size are presented following a discussion of XPS analysis that was used to gain insight into oxidative alteration of chalcopyrite’s surface chemistry. Chalcopyrite maintains its high flotation activity despite exposure to weeks of oxidative conditions. It is concluded that chalcopyrite is quite tolerant to stockpile oxidation due to various factors related to alteration of its surface chemistry.

Jan 1, 2012

By C. A. Sutherland

"Smelting of copper-gold ore from nearby Rossland mines started at Trail in the 1890s. As ore from the Rossland mines became exhausted, lead smelting of hand-sorted galena ore from other British Columbia mines was initiated. With the development of flotation technology for the separation of lead, zinc, and iron sulphides in the first two decades of this century, the large Sullivan orebody at Kimberley, British Columbia, became the f oundation for the growth of a major zinc and lead smelter at Trail. Lead smelting began in 1901, electrolytic zinc in 1916, and by 1984, the Trail metallurgical complex had produced 10 million tons of each metal. Its present capacity is 270000 tonnes per year of zinc and 110 000 tonnes/year of lead.This paper reviews the history of technological changes in the Trail production plants, emphasizing the zinc plant modernization program started in the 1970s, and also the planned introduction of the QSL oxygen lead smelting process in the late 1980s. Lead modernization will increase production capacity to a maximum of 160000 tonnes per year.IntroductionCopper-gold ore was discovered at Rossland, British Columbia, in the year 1890, starting a mining industry that was to last over three decade s. Selected ore was at first transported at high cost to distant U.S. smelters, so there naturally followed a decision to construct a small copper smelter to process the local ore to matte. It was built in 1896 at the mouth of Trail Creek on the Columbia River, about 10 km from Rossland. This little smelter was to develop and diversify in the next 90 years into the world &apos;s largest lead-zinc producer).The mining boom that occurred in the northwestern United States and southeastern British Columbia in the period of 1890 to 1910 saw the brief operation of many small local smelters. The only one to survive was the smelter at Trail. The circumstances that permitted its continued life and subsequent growth, form a fascinating history of business deals, litigation, andsteady technical progress.Early investment in local railway transportation and options by F.A. Heinze, the smelter&apos; s founder, attracted the attention of the Canadian Pacific Railway Company, which purchased Heinze&apos; s assets in 1898. This provided the capital base for survival and growth of the smelter, which remained and prospered under the Canadian Pacific umbrella for almost ninety years. It was registered as the Consolidated Mining and Smelting Company of Canada Limited in 1906; in 1966, this name wasshortened to Cominco Ltd.The Rossland mines continued to supply copper ore for the smelter until the late 1920s, but lead-silver ore also became available from the contemporary mining boom in the Slocan area, about 80 km away. In 1901, the Trail smelter diversified into lead; and when the CM&S Co. acquired the St. Eugene Mine at Moyie and the Sullivan Mine at Kimberley, the smelter was guaranteed a firm supply of lead ore. The company also purchased the West Kootenay Power and Light Company, which even before the turn of the century had constructed the first of four hydroelectric generating plants on the Kootenay River near Trail. This acquisition assured the CM&S smelter and its local mines of a stable power supply and the opportunity to diversify into power intensive technology."

Jan 1, 1988

By C. A. Sutherland

"Smelting of copper-gold ore from nearby Rossland mines started at Trail in the 1890s. As ore from the Rossland mines became exhausted, lead smelting offhand-sorted galena orefrom other British Columbia mines was initiated. With the development of flotation technology for the separation of lead, zinc, and iron sulphides in the first two decades of this century, the large Sullivan orebody at Kimberley, British Columbia, became the foundation for the growth of a major zinc and lead smelter at Trail. Lead smelting began in 1901, electrolytic zinc in 1916, and by 1984, the Trail metallurgical complex had produced 10 million tons of each metal. Its present capacity is 270000 tonnes per year of zinc and 110 000 tonnes/year of lead.This paper reviews the history of technological changes in the Trail production plants, emphasizing the zinc plant modernization program started in the 1970s, and also the planned introduction of the QSL oxygen lead smelting process in the late 1980s. Lead modernization will increase production capacity to a maximum of 160000 tonnes per year.IntroductionCopper-gold ore was discovered at Rossland, British Columbia, in the year 1890, starting a mining industry that was to last over three decade s. Selected ore was at first transported at high cost to distant U.S. smelters, so there naturally followed a decision to construct a small copper smelter to process the local ore to matte. It was built in 1896 at the mouth of Trail Creek on the Columbia River, about 10 km from Rossland. This little smelter was to develop and diversify in the next 90 years into the world&apos;s largest lead-zinc produce.The mining boom that occurred in the northwestern United States and southeastern British Columbia in the period of 1890 to 1910 saw the brief operation of many small local smelters. The only one to survive was the smelter at Trail. The circumstances that permitted its continued life and subsequent growth, form a fascinating history of business deals, litigation, and steady technical progress.Early investment in local railway transportation and options by F.A. Heinze, the smelter&apos; s founder, attracted the attention of the Canadian Pacific Railway Company, which purchased Heinze&apos; s assets in 1898. This provided the capital base for survival and growth of the smelter, which remained and prospered under the Canadian Pacific umbrella for almost ninety years. It was registered as the Consolidated Mining and Smelting Company of Canada Limited in 1906; in 1966, this name was shortened to Cominco Ltd."

Jan 1, 1988

By Kristopher John Shelswell

The work in this paper describes the theory, development and analysis of a computer model simulating a mine operation moving material using concurrent decline ramp truck haulage and skipping practices. This simulation was designed specifically to assess the performance of the truck haulage component and to expand on the scope and capabilities of traditional TKM fleet calculations. Haulage fleet simulation results were similar to TKM calculations for the lower to moderate production rate cases. However, comparisons of ramp-up and high production rate scenarios indicated that the simulation model was significantly more sensitive to operating practices and factors not accounted for by calculations derived when using a single TKM figure. Given the proper calibration of inputs and logic, the simulation model was additionally capable of providing information associated with general mine operations efficiency. Further benefits of the simulation model over a TKM approach included logistical assessments such as production schedule feasibility, productivity trade-off quantifications for proposed operating practices, and the validation of mine resource utilization scheduling. The simulation model was able to expand on traditional methods to approach planning and logistics by considering factors such as truck queuing, real-time traffic interactions, random events, and competition for resources on mine productivity.

May 1, 2013

By B. R. MacKay

Introduction The Corbin coalfield is one of the smallest, and at the same time one of the principal, producing bituminous-coal areas in southeastern British Columbia, and is unique on account of the great original thickness of one of its coal seams and the remarkable concentration of coal in a small area that has occurred through intense folding and faulting of the measures. These are such that the deposit has been referred to at times as "the world&apos;s thickest coal seam" and as" a mountain of coal." The determination of the number, thickness, and character of the seams present, and the structure, extent, and geological relationship of the several deposits, are of vital interest both to the operating company in its endeavour to evolve the most efficient method of mining these exceptionally thick deposits and to the Government in estimating the coal resources of the different fields. With the object of ascertaining these data the writer was assigned in 1930 to geologically map and study the Corbin coal deposit. A topographic map covering Coal mountain and the immediate vicinity on a scale of 1 inch =800 feet, with a contour interval of 25 feet, made by the Topographic Division of the Geological Survey, served as the base for the geological mapping.

Jan 1, 1931