Search Documents

By Steve Cole

"The economic and strategic importance of PGE bearing deposits is fuelling renewed exploration and development efforts in the precious metals mining sector.This paper presents a review of the various techniques used in the processing of PGE bearing ores, from primary benificiation to processing routes for the different flowsheets that have been developed amongst current producers. Recent innovations such as preconcentration of ore using gravity separation, recent trends in flotation circuit design and the development of hydrometallurgical routes for the direct treatment of flotation concentrates without the need for smelting will be discussed. Data from recent projects will be presented to illustrate common characteristics of PGE ores and concentrates.INTRODUCTIONThe six platinum-group elements (PGE): ruthenium, rhodium, palladium, osmium, iridium and platinum, together with gold and silver, are considered to be ""precious"" metals. The recent spike in platinum and palladium prices coupled with the projected increase in demand for the metals has fuelled a spate of exploration and new projects in the PGE sector. Historically primary producers of PGE metals have controlled the flow of information relating to the mining and processing of these ores into the public domain. Very little published information relating to individual operations and processes is available in comparison to the abundant literature relating to other metals.The purpose of this paper is to provide a general overview of the issues relating to the processing of PGE ores. Each topic discussed could easily be the topic of a paper or book and so in many cases only the surface of the topic will be scratched. An attempt has therefore been made to provide as many references as possible.This paper discusses the classification and location of PGE ores, the mineralogical factors that affect recovery of PGE's, methods currently used for recovering PGE's and process trends in PGE metallurgy."

Jan 1, 2002

By A. S. MacNeil

In the operation of any colliery, a factor of prime importance is power, of which there are three sources available--man, horse, and mechanical. It is obvious that man-power is by far the most expensive, .and that animal-power, also, is more costly than mechanical. In recognition of this fact, mine owners must, for economical ?reasons, reduce the use of man-and horse-power to the minimum by the increased use of machinery. In other words, they must aim at as complete mechanization as conditions will permit, taking advantage of existing physical factors that are favourable and making the necessary adjustments and modifications to meet the less favourable conditions. Intensive coal-mining, or the concentrated production of coal, has two distinct objectives: First, the maximum production from a limited area, in a given time, thereby reducing the pit-room to be maintained; and second, reduction in cost. To this end the coal should be mined, loaded and delivered to the surface by mechanical means wherever possible. To do this, however, requires the solution of many problems arising out of the varying conditions that obtain underground. The system of longwall mining lends itself to a more efficient scheme of mechanization than does pillar-and-room, as, in the former, the first step has already been taken by the removal of all the coal in one operation, and the opening-out of one face, the equivalent in mining area of fifteen or more rooms. Much has been clone of late towards mechanization in the longwall mines of the Sydney coal-field, and with gratifying results, but not without great difficulties and frequent disappointments. In 1923, an attempt was made with shaker conveyors. The introduction of conveying was a step to bridge the gap between the face, where the coal is produced, and the main transportation arteries leading to the slope or shaft. The receiving of the coal at the faces and its delivery to main loading points on main haulage-ways was the part allotted to the conveyors.

Jan 1, 1932

By D. Milne, G. Snell

"A new method to predict stope hangingwall failure in underground excavations is proposed. This method compares movement rate for stope hangingwalls, determined from changes in strain or deformation, with changing opening geometry. This geometry is represented by the effective radius factor (ERF), a measure of relative distance to supporting abutments from an opening surface point. This strain-ERF (SERF) approach is applied to an instrumentation program for Brunswick mine near Bathurst, New Brunswick. The SERF method for this case study predicted failure at an ERF of 13.9 m and hangingwall failure actually occurred at an approximate ERF of 12.4 m.RÉSUMÉ Cet article propose une nouvelle méthode permettant de prévoir la rupture de l’éponte supérieure des chambres d’abattage dans les excavations souterraines. Cette méthode compare la vitesse de mouvement des épontes supérieures des chambres d’abattage, déterminée à partir des changements aux niveaux des contraintes ou de la déformation, à la géométrie variable de l’ouverture au jour. Cette géométrie est représentée par le facteur du rayon effectif (ERF, de l’anglais Effective Radius Factor), une mesure de la distance relative jusqu’aux appuis latéraux de soutènement à partir d’un point de la surface d’ouverture au jour. Cette approche contraintes-ERF (SERF, de l’anglais strain-ERF) est appliquée à un programme d’instrumentation pour la mine Brunswick située près de Bathurst, dans le Nouveau-Brunswick. Pour cette étude de cas, la méthode SERF prévoyait une rupture à un ERF de 13,9 mètres (m); la rupture de l’éponte supérieure s’est effectivement produite à un ERF d’environ 12,4 m.INTRODUCTIONUnderground stope design can be improved with the installation of field instrumentation. The most commonly used instrumentation for monitoring rock mass behaviour around open stopes is extensometers. The y-axis of Figure 1 represents how the changing rate of movement, measured using either displacement- or stress-type instruments, can be observed over time. The magnitude of movement measured by extensometers can give an approximation of the load on installed support (Milne, Pakalnis, & Lunder, 1996) and a changing rate of movement can indicate approaching instability."

Jan 1, 2018

By G. E. Veins

A three-phase, continuously-operated, 250 kv.a. electric smelting furnace has been installed at the Mines Branch, Department of Mines and Technical Surveys, Ottawa, for the experimental treatment of ores and by-products of interest to the Canadian mining, metallurgical, and chemical industries. In the operation of this furnace particular emphasis is placed on the accumulation of quantitative data which will be useful in determining the most suitable smelting technique and the nature of the products, and in arriving at preliminary conclusions regarding the cast of power and electrodes. The results obtained in the experimental smelting of iron, manganese-iron, titanium- iron, nickel, and chromiumiron ores, and of a number of industrial by-products, clearly show the value of such treatment for materials of this type.

Jan 1, 1957

By John W. Bell

A FEW years ago the writer had the privilege of examining a piece of apparatus in the Forest Products Laboratory of McGill University which engaged his attention. The Forest Products Laboratory has an excellent installation of wood-grinding machinery, and the officials in charge were naturally interested in acquiring means for estimating the fineness of various wood grinds. The problem was referred to Dr. O. Maass ( l ). Dr. Maass designed a piece of equipment to measure the surface of a wood grind and derived an equation applicable in calculating its value, as follows : After inspecting this apparatus, the writer was disposed to believe that, with some modifications, Dr. Maass' ingenious idea might be utilized to measure the surface of mineral powders. Obviously, some difficulty would be found in maintaining an even suspension of mineral particles of high specific gravity compared to that of wood pulp. The writer will not bore the reader with a description of the various machines built and tried out. Some of these were satisfactory enough to obtain some valuable information, and to bring to light a difficulty which threatened to bring the investigation to an abrupt ending. For the mineral quartz, it was found that Kin the formula above stated was not a constant.

Jan 1, 1944

By Ralph H. Cleland

GENERALLY speaking, the Industry lost ground in 1941 in its accident experience. Though the frequency of compensation accidents was but slightly higher than in the previous year and well below past experience, our fatality rate shot up to that obtaining in 1938, and the average cost per man employed was the highest for some time. The number of fatalities was 56 in 1941 as against 33 in 1940. The average cost of compensation per man employed was $34.25 in 1941 as against $28.43. There was but a slight increase in the number of men employed. Accident prevention efforts were maintained, as shown by our frequency, but our accidents were of a more serious nature. In a period of considerable labour turnover, with many new men entering the Industry, especially the base-metal division, and much mental distraction, we might well have expected a high rate of accidents. That this did not occur is a tribute to managers, supervisors, and workmen alike. We all regret the high fatality rate and one must consider why this occurred. So far as it is possible to determine, there is no apparent explanation. There were no disasters. The accidents occurred to the same class of work-men, both in respect to jobs and age groups, and from the same age-old causes that we all know so well. Luck is a big factor in the seriousness of an accident; the solution lies in preventing accidents, even first-aid cases. Generally speaking, if minor accidents do not occur, major accidents do not occur.

Jan 1, 1942

By M. Kalin

"SUMMARYWaste management in general, and the water treatment of mine and mill effluents, has become an ever increasing burden for mining operations. A reduction in these expenditures would undoubtedly be desirable if this could in fact be achieved within effluent guidelines and monitoring requirements.A brief summary is presented of the research which has as its aim the development of methods which would reduce such costs and lead to solutions for environmentally acceptable close-out conditions for acid generating mine waters. The basic concepts of Ecological Engineering and Biological Polishing are presented, together with an indication of the present state of these research efforts. Details are provided of the progress of various experiments which aim to promote reducing conditions, organic matter production and the establishment of biological filters which remove metals from the water which are then retained within the waste management areas. These conditions should lead to a curtailment of acid drainage and an improvement in effluent quality.A description is provided of the first pilot demonstration using this approach to achieve a walk-away condition for the close-out of a massive sulphide tailings resulting from 10 years of operating a copper/zinc concentrator in Northern Ontario.1.0 INTRODUCTION1.1 Waste management and close-outIt is recognized that the achievement of a cost-effective and competitive mining operation, from the commencement of exploration for ore bodies through to the day-to-day efficient operation of the mine, requires a certain expertise and sophistication. However, the environmental effects of these activities are considered peripheral issues and their importance as an integral part of the planning and development of the mine/mill, is not always appreciated."

Jan 1, 1988

Many mines in Canada, the US and S. Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due the excessive weight. It has been suggested (DeLorme, 2000), that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm(1 ¾ in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg(10 ton) skip may exceed the safety factor of the rope. To improve on the current understanding of the mechanical behavior of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modeling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca 1995b) is used to simulate the structural behavior of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modeling on the wire rope will be discussed.

May 1, 2002

By A. Rodriguez-Prado, R. L. Legge, W. C. Lennox

ABSTRACT It is possible to adequately describe chemical reduction of hexavalent chromium, Cr(VI), in industrial and mining wastewater in constructed wetlands by applying different kinetic models (e.g., halforder, second-order). Accounting for hydraulic transport of contaminants in reduction equations can also improve such description. The authors developed an explicit advection-dispersion bulk flow equation and applied it to model Cr(VI) reduction in laboratory wetland mesocosms. The results indicated that the model adequately described wetland exit Cr(VI) concentrations and Cr(VI) reduction, representing an improvement over the commonly used graphic method and potentially improving the wetland design.

Jan 1, 2014

By Š. Šachlová, T. Lokajícek, M. Petružálek, T. Svitek, A. Štastná

During the past 20 years, alkali silicate reaction (ASR) as a cause of concrete deterioration has been studied by a wide range of experimental methods such as microstructural and macrostructural analysis, bulk chemical analysis, X-ray and neutron diffraction analysis, etc. All of these data are compared with expansion values of mortar bars (following ASTM standard C 1260). Recent studies indicate the useful application of non-destructive methods with the aim of better reflecting mechanical properties and the degree of deterioration of real concrete. Ultrasonic testing methods (including ultrasonic pulse velocity UPV) are widely used to determine material mechanical properties and the changes induced by a variety of mechanical or chemical processes. However, only a few laboratory studies of ASR focused on ultrasonic testing of mortar bars. Due to this fact, a heating chamber was designed and constructed to enable ultrasonic sounding of mortar bar specimens while stored in accelerating solution. Regular ultrasonic sounding of mortar bars reveals significant dependence of ultrasonic data such as longitudinal P-wave velocity, signal energy, signal amplitude and signal frequency on mortar bar storage time. Ultrasonic data were subjected to time domain as well as frequency domain analysis. Different storage conditions were used to determine the effect of ASR on ultrasonic parameters. Mortar bars, prepared in the same manner with one type of aggregate, were stored in cold or warm water or in an accelerating warm medium. Ultrasonic data accurately reflects the differences in hardening and deterioration of tested mortar bars due to different storage conditions. Ultrasonic results showed very good correlation with the results of ASTM standard expansion tests and much higher sensitivity to ASR-induced concrete deterioration. Expansion tests showed 1% measured length differences in comparison with up to 80% resolution of ultrasonic data. The ultrasonic testing proved to be a suitable laboratory method for investigating ASR-related processes and could lead to an improvement of standard testing procedures.

Jan 1, 2015

The Industrial Minerals Milling Section of the Mineral Processing Division has been engaged for the past three years in a study of the separation of minerals, by means of electronic sorting equipment, on the basis of their colour. Considerable knowledge of the subject has been built up. Because the object of this study is application as a means of beneficiation, a number of examples of the separations achieved are presented. Introduction T 0 the mineral collector, the colour of a mineral may be pleasing, even fascinating; to the mineralogist, student or professional, it may also be practical. It serves, to some extent, as a distinguishing feature in many minerals, and helps to fix with reasonable accuracy the identity of a few. It may now become a useful tool of the mineral dresser. The idea of using a difference in colour as a means of separation of one mineral from another is not new. Hand sorting dates back to ancient time. However, the means by which this can be done mechanically was developed only during the past decade. As far as the Mineral Processing Division is concerned, interest dates from March, 1960, when the following item was observed in the

Jan 1, 1965

Mineral resource development activities impact the health and well-being of many people, from workers, to families and surrounding communities. In the decade up to 2010, mining revenues increased from 6% to 14% of Australian GDP, and minerals contributed 55% of total exports, with a growth in mining employment from 1% to 1.7% of the national workforce (Connolly and Orsmund, 2011). The growth in Australia?s minerals operations is mostly located in remote areas, or in rural communities with a limited population. As a result, operations have increasingly implemented long distance commuting (LDC) programs, often called ?fly-in, fly-out? (FIFO) and ?drive-in, drive-out? (DIDO), as a staffing strategy to meet rapid industry growth in locations with limited local populations. The rapid expansion of the minerals industry has resulted in considerable public debate about the benefits and costs to all sectors of Australian society. In response to the concerns of constituencies from many parts of Australia, the Minister for Regional Australia, Regional Development and Local Government, The Hon Simon Crean MP, asked the House Standing Committee on Regional Australia on Tuesday 23 August 2011 to inquire into and report on the use of ?fly-in, fly-out? (FIFO) and ?drive-in, drive-out? (DIDO) workforce practices in Regional Australia. The recently published report highlights the national interest and the diverse opinions about this practice in Australia. Resource extraction companies have developed several options to meet the accommodation requirements of their long distance commuting workforce. In this paper, initial results are reported from an ongoing survey of FIFO (and other non-residential) resource industry workers (n = 286) in the Australian resource extraction industries. The purpose of this study was to better understand how accommodation arrangements may impact on the health, wellbeing and job satisfaction of non-resident workers; and to attempt to find a relationship between different accommodation variables and workforce wellbeing and retention. In doing this it investigates evidence for the linkage between accommodation factors, hours of work, health, well-being, job satisfaction and job retention in the LDC work force.

Aug 1, 2013

By R. N. Chakravorty

Early detection of spontaneous combustion is of utmost importance in underground coal mining to prevent major disruptions of production and to ensure a safer working environment. This paper presents the work done in developing a suitable system for the early detection of heating in a hydraulic coal mine. Laboratory studies on the products of oxidation for Balmer 10 seam coal showed that a significant amount of carbon monoxide is produced during the early stages of heating and that detection methods based on the analysis of other gases, such as hydrogen, ethane or ethylene, are not a better alternative for this coal. The four-point carbon monoxide monitoring system recently installed at the hydraulic mine is discussed in this paper. It is believed that by studying the trend of carbon monoxide concentration in the mine air, it will be possible to detect heating at an early stage. Field tests carried out so far have indicated that infra-red technology will prove to be a powerful tool in the hydraulic mine, particularly for locating hidden oxidation or fire in cracks, fissures, underground workings and coal outcrop areas before it spreads extensively. The project is jointly sponsored by EMR, CANMET, Mining Research Laboratories and Kaiser Resources Ltd.

Jan 1, 1978

By L. T. Loe, A. S. Norsk, Mo i. Rana

High production rate and good stability demand the optimization of all phases of electric pig iron smelting. This is important with respect to slag chemistry, which to a large extent regulates the process temperature in electric smelting. Controlled basicity and slag volume. and a satisfactory screen analysis of the reduction material and sinter, are of the utmost importance for smooth furnace operation. Large variations in slag volume and in B/ A and C/Fe ratio will have an influence on the furnace resistance and thus the specific energy development in the furnace, which lead to variable reduction of SiO.. The result will be variable hot -metal quality and un-stable furnace operation.

Jan 1, 1970

By J. E. Danoczi

ABSTRACT A diamond processing plant is being designed for the Star–Orion South diamond project in central Saskatchewan. Key to the plant is diamond liberation, which occurs in the comminution section and is the process of breaking up kimberlite rock as gently as possible to minimize diamond damage, particularly in larger, high-value diamonds. Kimberlite from the crater area of a volcanic pipe is generally softer than kimberlite from the diatreme zone. Softer kimberlite, comprising the majority of Star– Orion South deposits, can be readily broken up using abrasion and attrition by autogenous grinding mills, the preferred comminution method for minimizing diamond damage.

Jan 1, 2013

By D. Gendzwill, N. Martin

"In early 1987, the Patience Lake potash mine near Saskatoon, Saskatchewan, was closed due to uncontrollable floodingWater inflows were first encountered during routine mining in 1975 at the south boundary of the mine lease. Underground grouting and construction of bulkheads limited the flo but did not completely stop it. Subsequent seismic surveys showed that the mine had approached the edge of a large collapse structure in which the salt and potash had been partly dissolved and removed by groundwater.In 1986, the small flow into the mine started to grow. Despite renewed grouting, the flood increased and outstripped pump capacity. The grouting program temporarily slowed the inflow but was unable to stop it. Eventually, from seismic and drilling evidence, it became clear that the water source was an extensive system of vertical fractures which would be impossible to seal by drilling and grouting from underground. A new plan to install 14 bulkheads underground would have sealed the water source from the rest of the mine but the construction program could not be completed before rapidly increasing inflow threatened to fill the mine. The underground mine was closed and a new solution mine started in 1988."

Jan 1, 1996

By Michael Harley, E. Guy Charleworth

"Bedding-parallel thrust-hosted gold veins are developed in the Sabie-Pilgrim's Rest goldfield, eastern Transvaal, South Africa. The reefs display a complex history characterized by temporally and spatially overlapping events of similar mineralization and deformation. Recognition of the episodic reactivation of these low angle (5° to 10°) thrust faults implicates high fluid pressures (equalling or exceeding lithostatic pressures). Geochemical constraints limit the amount of fluid-rock interaction and the occurrence of transgressive mineralization within the Archaean granitoid basement suggests that the high pressure fluids originated at depth beneath the Transvaal Basin.Similarities exist between gold deposits of Sabie-Pilgrim's Rest and Telfer, Western Australia as well as Passagem de Mariana, Minas Gerais, Brazil. All deposits are sub-parallel to the enclosing bedding which is shallowly inclined. Furthermore, they are also hosted by contractional deformational structures and are clearly epigenetic in origin."

Jan 1, 1994

By G. G. Manekar

MOIL Limited (formerly Manganese Ore India Limited), a Government Enterprise, under the Ministry of Steel, Government of India, produces about 1.1 million tonnes (T) of manganese ore annually from three opencast and seven underground mines. The underground operations are mining using an overhand cut and fill method. The orebody is too narrow for the use of larger equipment and the poor to fair rock mass quality limits the size of stable excavations. Prior to the 1990s underground support consisted primarily of timber square sets in tandem with timber chocks and props. As mine production requirements increased throughout the 1990s led to larger opening sizes and more modern support practices. Research was conducted on ground support design based on rock classification and empirical techniques for designing ground support. Based on the findings and field trials, the Company adopted full column cement grouted cable bolts for back support. Instrumented field trials, using extensometers and load cells on the cable support confirmed the support effectiveness. Stope design was based on two and three dimensional stress modeling which resulted in a significant increase in stope dimensions. The rock mechanics studies for safe stope design were carried out using numerical modeling tool in two and three dimensions for the analysis of stresses. Based on the findings, the safe stope geometry with new stoping parameters was introduced. The earlier stope length of 30 mtrs were changed to 60 mtrs with in situ rib pillar at the cross cuts and in situ post pillars to be left-out in the stope. This leads the formation of of panel comprising of three stopes, for production, supporting and filling. For mechanical handling of ROM in stopes Side Discharge Loaders (SDL) were introduced. The above changes have improved the face productivity from 2?3.5 T with manual operation and 9 T with SDL. The above rapid mining operations has improved the stope productivity but reduced the stope life from 6 to 3 years. For the improvement of the stope availability, further studies were conducted by numerical modeling of stress analysis. The related studies confirmed that with the existing supporting system and proper instrumentation, level interval could be increased up to 45 mtrs from the existing 30 mtrs at deeper levels. At present below 12th Level interval is 45 m at Balaghat Mine. For future mechanization program for introduction of Single Boomers, LPDT, Cutting Machines etc for the development headings rock mechanics studies are underway. The paper provides details of rock mechanics studies that were carried out to study efficacy of the cable bolt support, safe stoping parameters and increased level interval for the improvements in safety, production and productivity at Balaghat Mine.

Aug 1, 2013

By C. Pelley, S. Kelebek, G. Kunzel, S. Gregersen, M. Pollanen

A series of small-scale tests was conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson’s ratio, Pwave, S-wave velocity, point load test index, crushing, and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with a lowstrength detonating cord to a combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

Jan 1, 2006

By C. Nikolic

A process utilizing ozone for the precipitation of cobalt from nickel sulphate liquors containing ammonium sulphate has been developed. Best results were obtained using nickel carbonate to maintain solution pH at 5.0 to 5.5. Work was performed both in column and stirred-tank reactors. Variables studied included neutralizer type and concentration, NH4+ concentration, temperature, Ni++ and Co++ concentration, per cent O3 in the O2 carrier gas, O3 input rate and agitation. The over-all rate of cobalt rejection increased sharply with increasing agitation and ozone concentration in the gas phase, reflecting relatively slow transfer of ozone from the gas to the liquid phase.

Jan 1, 1978