Search Documents

By J. Talja

"Non-ferrous metal concentrates contain typically 7 – 12% water when received at the smelter. Removal of this water prior to smelting is always economically feasible because unnecessary heating of vapour (from 100 °C to 1200 °C) in the smelting furnace can thus be eliminated. This results in major reduction in CO2 emission and direct annual savings of several millions of dollars due to improved energy efficiency. Next step to further improve the energy efficiency, to gain substantial savings and simultaneously cut emissions is to select modern technology for the drying process. Consequently, all CO2 emission will be completely eliminated (from 40,000 tpy down to 0 tpy), NOx emission will be negligible, and the SO2 emission will be reduced by over 99 %. Switching of conventional direct heated drying technology to modern indirect steam drying brings, in addition to dramatic emission reduction, additional savings due to further improved energy efficiency. Direct energy savings count for 900 – 1300 MJ/t H2O, which depending on the concentrate feed rate and its moisture load can be worth several millions of dollars every year. Additional savings in operational expenses related to drying and gas cleaning may be worth a few million dollars more. Sustainability is a key issue today, and major savings together with significant emission reduction are readily available by proper technology selection for concentrate drying. INTRODUCTIONSustainability is a decisive principle in any process industry accompanied with emissions and high amount of energy. This is of significant importance in metal processing, including concentrate drying, where minimum impact on the environment, people and community are targeted, and all this with minimum cost, effort and resources. Therefore, special attention is paid to high energy efficiency, low energy consumption with preferable utilization of waste energy, safety issues, availability, level of maintenance, cost of maintenance, and emissions among other things.Non-ferrous metal concentrates can be dried using various techniques. Conventional drying based on direct heating, and use of fossil fuels for drying energy has almost entirely been replaced by steam drying. It is based on indirect heating and it has become the most dominant drying technology for copper concentrates during the last decade with over 90% of the market share of all new dryer installations. Among the steam dryers the Kumera Steam Dryer is the most pre-dominant technology with some 70% of all new dryer installations world-wide."

Jan 1, 2012

By J. L. Bowlby

Introduction In the following discussion, boiler-feed and mine waters will be considered from the point of view of the problems arising from the chemical nature of the mineral and gaseous impurities they contain. The theories underlying some of these problems will be reviewed for the purpose of getting a clearer concept of the problems themselves. Certain terms of a chemical nature, necessary to the discussion, will be explained on the assumption that they are not generally familiar to mining engineers. Finally, an attempt will be made to correlate theory and practice, with the abject of establishing certain limits to factors relevant to the problems, and to show that these limits are justified by practical experience. The general problems occasioned by the presence of mineral and gaseous impurities in boiler-feed and mine waters are: (1) Scale formation and corrosion in boiler systems. (2) Corrosion of mine pumps and pump fittings. These will be discussed separately. Boiler Scale Typical analyses of waters available for use in steam power-plants are given in the accompanying Table (Table I). All analytical data are expressed in grains per Imperial gallon. The bicarbonates of calcium and magnesium in the raw waters are shown as normal carbonates in the Table. Substances in the first five rows constitute the encrusting solids. All the waters listed in Table I would be classified as 'very good' in the schedule of classification for boiler waters adopted by the American Association of Railway Chemists in 1887. In spite of this classification, however, the waters contain sufficient encrusting solids to cause serious scale trouble after prolonged evaporation.

Jan 1, 1934

By I. Cotman

Dimensional stone processing has become an important part of the world extractive industry, and today?s total stone block yearly production is estimated to be around 134.000.000 tons and is still growing by an average yearly rate of approximately 20%. In future, the same production will become an important part of the mining industry and presently, in some countries it represents even the main mining output. New environmental regulations, together with landscape and nature conservation requirements, create a number of difficulties in setting up new open pit dimensional stone quarries. As a result, many dimensional stone producers have recently started to apply underground techniques in order to produce the ornamental stone blocks intended for further processing. Underground production of stone blocks requires special mining methods and so far it has not been a cost-effective excavation method for all types of rocks. Presently, this type of stone excavation is generally applied in sedimentary and marble deposits because the rock has small to no mineral quartz content. When starting a new underground dimensional stone mine, it is necessary to analyse the impact of all primary factors which are crucial to set up a technically and cost effective advanced underground dimensional stone mine. The role of physical and mechanical properties of the rock, geological conditions, mineralogical composition, micro-tectonic state of the site, rock mechanic conditions on the site, durability and saw ability of the stone are decisive factors in foreseeing the future methods of extraction. The laboratory research work as well as the field work, is very important in decision-making aimed to choose the future excavation method. Also of equal importance is the serious market research, because it renders the indication of selling price potential. Having obtained the results from both types of research, mining engineers can design the mining methods which optimize financial return to the mine. The practice approved by 15 years of testing in the underground limestone quarry of Kanfanar gives future producers very useful advice and general data to facilitate the process of exploration intended to establish new similar underground quarries.

Aug 1, 2013

By John Gittins

Lots 11 and 12, Range IX, Calumet island, are underlain by a Grenville metamorphic complex into which sills of tourmaline granite pegmatite have been injected. The pegmatite has an average mode-potash feldspar 65 per cent, sodic plagicdase 10 to 20 per cent, quartz 5 to 20 per cent, tourmaline 10 to 15 per cent, accessory minerals < 5 per cent; it is unzoned except for a narrow border zone. Some of the feldspar has been replaced by calcite. Microcline has been ?partially replaced by sodic plagioclase. Three varieties of tourmaline are present (black, blue, and green) and spectrographic analysis suggests progressive compositional changes during its crystallization. The presence of U- and Th-bearing minerals in the pegmatite prompted the Quebec Nickel Cor,porat10n, Ltd., to explore the possibility of developing the pegmatite but it does not appear that this is economically possible at the ? present time. Tt\e Grenville metamorphic complex consists of recrystallized limestones and calcsilicate rocks of the albite-epidoteamphibolite facies and the amphibolite facies, which were derived from sedimentary rocks. Several of these are dis-equilibrium assemblages, and retrograde metamorphism has probably formed biotite and epidote from hornblende. The schistosity of the gneisses dips steeply eastward. Numerous strike faults are roughly parallel to the schistosity and one of the pegmatite sills is bounded by such a fault, dipping at 60 ° with about one foot of fault breccia. The general structure of the map-area seems to be an asymmetrical syncline ?overturned to the west. The emplacement of the pegmatite is associated with a period of folding, metamorphism, and igneous intrusion.

Jan 1, 1956

By P. Dinham, G. C. Summerton, N. McCulloch, S. Dowling, D. C. Craig

"Development of a process for the treatment of a nickel copper matte rich in the minerals heazlewoodite, chalcocite and bornite has demonstrated significant base metal recoveries and metal separation efficiencies. The determination of chemical and mineralogical changes occurring in the individual leaching stages in laboratory experiments has enabled a better understanding of the complex leaching chemistry. The chemistry and mineralogy of the piloting and laboratory processes are discussed.INTRODUCTIONThe nickel-copper sulfide ores of the South African Bushveld Complex are among the most important Platinum Group Metal (PGM) bearing ores, and contain the world’s largest reserves of platinum. The treatment used in the recovery of PGMs from these ores includes three types of processes, namely ore concentration using physical techniques such as flotation and gravity separation, concentration by pyrometallurgical means, hydrometallurgical extraction of the base metals followed by the PGMs. Following milling of the ore, flotation involves the separation of high value minerals from gangue by taking advantage of the differences in their hydrophobicity. These differences are generally maximized through the use of a surfactant or wetting agent. Concentrates are then thermally treated and melted which brings about physical and chemical changes that enable the recovery of base metals and PGMs. The main aim of the smelting and converting process is to separate and eliminate the valuable metals from the bulk of the unwanted gangue and essentially all of the iron and to concentrate the metal VALUES (into a high grade converter matte. The matte can be further enriched by magnetic separation, producing a PGM-rich magnetic fraction and a base metal-rich non-magnetic fraction. The magnetic fraction is treated by hydrometallurgical processes to produce a PGM concentrate which is further refined to separate and purify the individual metals. The non-magnetic fraction is treated to produce marketable metal VALUES (such as nickel, copper, cobalt and to a lesser extent PGMs. The principal objective of any hydrometallurgical extractive process is to leach the desired elements selectively into an aqueous phase so as to separate them from the bulk of the material. (Crundwell, Moats, Ramachandran, Robinson and Davenport, 2011; Hundermark, Mncwango, de Villiers and Nelson, 2011)."

Jan 1, 2012

By D. Kong, A. Klyashtorin, L. McGilp, I. Wilson

This work reports on applying iron oxide coated sands media in an experimental permeable reactive barrier to remove uranium species from uranium containing water. A field experiment was conducted at the legacy Gunnar uranium mine & mill site that was abandoned in the 1960s with limited to no decommissioning. The flooded Gunnar mine pit presently contains about 3.2 million m3 of water contaminated by dissolved U (1.2 mg/l), Ra-226 (0.4 Bq/l), and minor concentrations of other contaminants (As, Se, etc.). The water is seeping over the pit rim into Lake Athabasca posing environmental and health concerns. Iron oxide coated sands can be used to immobilize uranium species through an adsorption process. Methods for preparation of hydrous ferric oxide sorbents and their supported forms onto silica sands are described. Fourier transform infrared spectroscopy (FTIR), and powder X-ray diffraction (pXRD) were used to characterize the physical-chemical properties of the sorbent. The monolayer uranium uptake capacity (Qm) was estimated through the Langmuir adsorption isotherm. Adsorption kinetic experiments were performed in a lab environment before moving to a field trial. Based on these lab results and the input on field-scale appropriate geometries, a pilot permeable reactive barrier was fabricated and a field test conducted near the Gunnar pit in June 2019. This pilot test provided technical data and information needed for designing a full-scale permeable barrier based on the iron oxide coated sands, which may be applied for in-situ water treatment at Gunnar and other legacy uranium sites.

Jan 1, 2020

By C. Droun

"Low back pains account for about 13 per cent of all compensation claims made to the Quebec Workmen's Compensation Commission and cost the employers a sum exceeding ten million dollars. The frequency and cost of these health problems in Quebec metal mines are proportional to the provincial trends. An elaborate review of the literature on the causes, nature and prevention of low back pain is made in this presentation. A prevention program for low back pain has been designed in cooperation with a team of seven medical specialists and two physiotherapists for the Quebec metal mines. The program is especially designed for persons who have had low back pain, in order to prevent a recurrence, and for persons beginning to feel chronic difficulties. It is based on existing programs at the Hawthorne Plant of Western Electric Company and at Minnesota Mining and Manufacturing, but it requires a much different approach because of the nature of medical care available at the mining sites. The program is difficult because it involves a change of attitude for every employee and every supervisor. The program, so far, is beneficial because several men are now seriously engaged in an active program of reconditioning and because the problem of low back pain ie beginning to be seen from a new angle."

Jan 1, 1973

By O. K. Mahabadi, A. Lisjak, B. S. A. Tatone, N. Vlachopoulos

"Numerical simulations are widely adopted in the design of several types of rock structures, including tunnels, caverns, rock cuts, and open pit and underground mines. In recent years, analyses based on the hybrid finite-discrete element method (FDEM) have been shown to provide a realistic representation of rock mass deformation and fracturing processes. To date, the FDEM approach has successfully yielded qualitative and quantitative results for several practical rock engineering applications, yet it has lacked the ability to consider the implementation of rock-reinforcement measures. Since rock reinforcement is often used in civil and mining applications to improve the strength and deformational behaviour of a rock mass, the ability to incorporate such features into FDEM analyses is essential to extend its applicability to a broader range of problems. The work presented in this paper represents an important first step towards developing a simulation tool that can be used for practical rock engineering applications, including the design of underground excavations and rock slopes.INTRODUCTIONRock support and reinforcement measures are often employed in civil and mining rock engineering projects in order to maintain or improve the strength and deformational behaviour of rock masses. The preferred type of reinforcement or support elements along with the preferred layout and timing of installation depend on the in-situ ground conditions, the nature of the rock mass and excavation method. Over the last two decades, numerical modelling has been increasingly used to design and attempt to optimize rock reinforcement and support systems. As such, most rock engineering-specific modelling software now offers various approaches for modelling different rock reinforcement and support elements."

Jan 1, 2015

By F. J. Alcock

THE Magdalen islands have recently been attracting attention as a possible source of manganese. As early as 1880 small masses of manganese oxides were known to occur in the soil and at least one attempt was made to develop them. In 1939, after the outbreak of war, interest in the possibilities of the field was again aroused and during the winter of 1939-40 claims were taken up by two groups of Toronto interests. The islands also contain large quantities of gypsum. During the summer of 1940, the writer mapped the islands geologically, giving particular attention to a study of the manganese occurrences. For a base-map, the chart of the islands was enlarged to a scale of half a mile to an inch. Additional roads were added from traverses carried out in connection with the geological work, and form lines with approximate 100-foot intervals were put on from barometer readings. The geological map is the first that has been prepared of the islands. Previous Work In the summer of 1880, James Richardson of the Geological Survey of Canada studied the rocks of the islands and his r~port concerning them appears as Part G of the Report of Progress, 1879-80. In 1903, J. Obalski, Inspector of Mines for the Department of Lands, Mines and Fisheries of the Province of Quebec, visited the islands, chiefly to investigate the occurrences of manganese and gypsum, and his notes are found in the report on mining operations in the Province for that year. Around 1890, Robert Chalmers of the Geological Survey paid a visit to the islands, and his observations, which chiefly concerned the surface geology, appear in the Annual Report of the Survey, Vol. VII, 1894, Part M, p. 94. The next geological work was carried out by John M. Clarke, Director of the New York State Geological Survey. Clarke paid many visits to Gaspé peninsula between the years 1900 and 1920, collecting fossils and gathering h1s~orical data, and extended his investigations of Gaspé county over to the Magdalens. His Observations on the Magda/en Islands is included in the New York State Museum Bulletin 149, seventh report of the Director, 1910.

Jan 1, 1941

By J. E. Hawley

This paper constitutes a report from the Committee on Geological Research to the Geology Division of the Institute. Two years have elapsed since a formal report was made containing several resolutions aimed at assisting geological research, a review of research equipment available, a summary of research projects suggested for consideration, and a list of research then in progress (see July, 1947, Bulletin, pp. 351-370). At this time we may note what action has been taken on the various resotions and suggestions of the Committee, indicate the more important accomplishments of independent investigators, and present a summary of the rather imposing volume and variety of research currently being carried on throughout the country. I.-Committee Resolutions and Suggestions 1.-A National Advisory Committee on Research in the Geological Sciences The original resolution adopted on the setting up of this Committee was approved with despatch by Council and was forwarded to the Minister of Mines and Resources. Due to a reorganization in the Department and possibly other reasons, no action on this important matter has yet been taken, but we are assured that some time this year such a Committee will be established by the Department of Mines and Resources. Unquestionably, it will give a fresh impetus to research in the geological sciences. When the noteworthy progress made by the research committees on Geophysics and on Soil and Snow Mechanics, established by the National Research Council, is considered, it is indeed regrettable that the Department of Mines and Resources has not acted more decisively in this matter.

Jan 1, 1949

By Robert B. Parsons

"Investors in flow-through shares are going to need an expanded road map to find their way through a growing maze of tax rules affecting such shares. At the end of 1985, no fewer than three new sets of important tax amendments were tabled which could have a significant effect on flow-through share issues. This proposed legislation is discussed this month in Tax Notes.IntroductionIn a flurry of legislative activity at the end of 1985, the federal government tabled legislation which includes the introduction of new rules which will have a notable effect on investors in flow-through shares and on companies that issue such shares.First, on November 26, 1985, Bill C-84, the legislation to implement most of the changes announced in the May budget, was introduced in Parliament. This legislation includes the rules for the $500,000 capital gains exemption, a matter of considerable interest to flow through share investors.Next, on December 2, 1985, the government tabled a Notice of Ways and Means Motion which would extend the time horizon for spending flow-through share funds to include the 60-day period following the calendar year. But all news was not good news. On December 4 the government released its proposals for a minimum personal income tax, which would include rules that would catch an investor&apos;s CEE expenses and capital gains."

Jan 1, 1986

By Z. D. Hora

"There has been a number of new developments in British Columbia&apos;s industrial minerals field over the past few years. Several new industrial operations were started to diversify the line of British Columbia mineral production by magnesite, perlite and fuller&apos;s earth. Industry activities and geological projects have identified occurrences of rare earth minerals, niobium, kaoline, fireclay and zeolites. The Geological Survey Branch significantly improved its database on industrial minerals. New geological concepts based on recent work are opening a number of new opportunities f or further industrial minerals&apos; exploration and development in British Columbia.IntroductionTraditionally, the value of industrial minerals produced in British Columbia in any given year comprises between 100/0and 15% of the combined value of minerals, coal, petroleum and natural gas. Over the years a wide variety of industrial minerals has been produced , often with different levels of marketings success. For some products, such as dimension stone and clay or shale products, initial strong demand gradually dissipated; for others such as asbestos and magnesite, new discoveries or new industrial activities created demand and new markets . In some cases, such as fluorite , talc, pyrophyllite and perlite, wider use has been prevented by small size, poor quality or remote location of the deposits. Also, British Columbia , with 2.6 million inhabitant s, provides only a limited market and the industry therefore has to look beyond provincial borders."

Jan 1, 1990

By W. H. Stheeman

"The high rock pressures at the deeper levels of the Tsumeb Mine have necessitated the changing of the mining methods and the introduction of cable bolts. After two rockfalls in the cable-bolted stopes, the mechanics of cable bolting were investigated. Practical methods were developed to find the best grout mixtures, the bond stresses between cables and cement, the bond stresses between rock and cement and the load on the cable bolts, which was mathematically calculated from data observed underground. The design of the cable bolt support system as used at the Tsumeb Mine is explained. GeneralThe Tsumeb Mine is in northern South West Africa/Namibia, approximately 400 km by road from the capital city, Windhoek, at an elevation of 1300 m above sea level. Mining operations in Tsumeb were started in 1905 by the Otavi Minen und Eisenbahn Gesellschaft and continued, with an interruption during the Depre ssion, until 1940, when the mine was closed and taken over by the Custodian of Enemy Property. The present owner, Tsumeb Corporation Limited, obtained the mine in 1947 and restarted the underground mining operations in 1949 after the mine was dewatered. Currently, the stoping operations are between 26 Level (840 m below surface) and 38 Level (1260 m below surface). In addition, the mine is an important silver producer and has produced 670,100 kg of silver since 1947."

Jan 1, 1982

By J. O. Marsden

Over the past decade, the copper industry has been through an extended downturn followed by several years of sustained high copper price. A number of new technologies have been developed over the past 10 years aimed at reducing costs by decreasing energy, labor, and materials requirements, or by increasing metal recovery. The energy intensity of different copper extraction routes and different technologies varies considerably and this has a significant impact on the economics of extraction. Based on average ore grade materials, the total energy for the extraction of copper typically varies from about 24-26 MJ/lb (6.7-7.2 kWh/lb) for the mining, crushing, milling, flotation, smelting and refining route to about 14¬16 MJ/lb (3.9-4.5 kWh/lb) for the mining, crushing, heap leaching, solution extraction and electrowinning route. New technology developments are providing opportunities for significant reductions in energy consumption for copper extraction, representing energy savings up to 20-25% in some cases. In addition, in many cases, these new technologies have introduced environmental, safety and health benefits over the incumbent technology. Some of these technology developments have been more successful than others, and many hold great promise for application in the coming decade. This paper provides an overview of the technology developments that have occurred, and explores the underlying reasons behind successful implementation.

Jan 1, 2007

By F. Hassani, R. Mikaeil, B. Ferdowsi

Two analytical solutions for estimating the ovaling deformation and forces in circular tunnels are widely used in engineering practice, due to soil-structure interaction under seismic loading. This paper discusses the discrepancy between the two analytical and finite difference methods. A comparison of the two analytical methods shows that the calculated forces and displacements are identical for the condition of full-slip between the tunnel lining and ground. However, the calculated lining thrusts differ by an order of magnitude when considering no-slip between the tunnel lining and the ground. The analytical solutions are compared to numerical analyses of the no-slip condition using the finite difference method to validate which of the two methods provide the correct method. To achieve the goal, numerical modelling, field data of the Kuhin railway tunnel and Manjil earthquake characteristics are used. Numerical analysis results agree with one of the analytical solutions that provides a higher estimate of the thrust on the tunnel lining, thus highlighting the limitation of the other analytical solution.

Jan 1, 2008

By E. Poiate, P. R. Cabral, A. V. N. Santos, P. V. M. Costa, C. S. Amaral, A. M. Costa

This paper discusses the design of underground salt caverns, opened by solution mining, for the production of brine and storage of natural gas under high pressures. The caverns are located in the salt basin in Maceio City, Alagoas State, at the northeast region of Brazil. Special attention is given to the geomechanical structural design of the caverns using computer codes specially developed for the simulation of excavations in salt rock formations, considering validated constitutive creep laws under different initial stress states and temperatures. The behavior of sedimentary rocks intercalations presented in the salt layer is simulated using elastic-plastic models. The excavation of the caverns by solution mining is also simulated starting from a geostatic initial equilibrium state of stresses, with a unique formulation only implemented in these computer codes, without the need of the application of boundary stresses to the model in order to develop the initial state of stresses. These computer codes have being used in the design of several clusters of caverns for brine production used as raw material of Poly Vinyl Chloride (PVC) of the Chemical Industryin Brazil. These computer codes and methodology were also applied to the design of the underground conventional potash mine in the state of Sergipe, overlying tachyhydrite and carnallite with very high creep strain rate. They have also been used in the design of the pre-salt oil wells through thick layers of stratified salt rock in Santos Basin, for the exploration and production of the pre-salt reservoirs in Brazil. The constitutive creep equations implemented in the codes are based on a double mechanism creep law. The creep constants adopted in the simulation are taken from a previous investigation carried out on an experimental panel of the potash mine, considering the stratified geology with different salt rocks of the basin where the mine is located. These constants were also obtained by lab tests under different confined and differential stresses and temperatures.

Jan 1, 2015

By D. C. Reid

This paper describes the latest results in research and development currently being undertaken by the CSIRO Mining Technology Group to advance the automation capability of continuous mining equipment in underground coal mining operations. This research delivers enabling technologies that are essential in achieving increased roadway development rates as well as providing a safer working environment for underground mine personnel. Details are presented on technical developments and results of large-scale above-ground experiments conducted under field-realistic conditions. These experiments demonstrate the performance of the ?self-steering? capability which will enable a continuous miner (CM) to automatically maintain a given mining heading and mining horizon under production conditions. A primary technical requirement of this automated functionality is the means to accurately determine both the location and orientation of the CM in real-time. Test results of a high performance navigation system utilising vehicle motion aiding technologies are presented. This system combines high performance inertial sensors, and custom-developed radar to achieve a navigation-grade guidance system. Comprehensive performance evaluation has been conducted using a scale skid-steer mobility platform operating autonomously through a typical roadway development mining pattern with a total path length of 2700 m and mission duration of 112 min. Results from this evaluation demonstrate that the sustained accuracy of the navigation system exceeds the original project expectations and is well suited to the requirements for this underground mining application. There are presently no known alternative methods for providing a practical and accurate three-dimensional guidance solution in this application. This achievement represents a significant milestone in delivering a step change improvement in underground coal mining roadway development.

Aug 1, 2013

By J. Peterson, D. D. Tannant, J. Todd

"A review of blast designs and improved blasting practices at the EkatiTM diamond mine is presented along with the results of three blast-monitoring experiments. Blast monitoring was undertaken to investigate blast damage mechanisms in the mine’s well jointed rock mass. Rock mass damage caused by production, pre-shear and wall control blasts was measured. EkatiTM uses 270 mm holes for production blasting, and 165 mm holes loaded with a decoupled charge for pre-shearing. The production blasts are loaded with bulk emulsion/ANFO blends. The mine plan involves using 30 m double benches. A 30 m high pre-shear is drilled and blasted prior to the production blasting that is done with sequential 15 m benches. This paper summarizes the monitoring equipment and data gathered to date. IntroductionThe EkatiTM diamond mine is located about 300 km northeast of Yellowknife, Northwest Territories, Canada. The mine is a joint venture of BHP Diamonds Inc. (80%) and geologists Charles Fipke and Stewart Blusson (10% each). The EkatiTM mine is Canada’s first diamond mine and BHP is the operator. The mine is accessed by air and by a winter ice road.The first kimberlite pipe mined at EkatiTM is known as the Panda pipe. The Panda open pit mine will have a total depth of 315 m (Fig. 1), a width of about 600 m, and a 50° overall slope. Initial ore production is 9000 tonnes per day.This paper summarizes the pre-strip blasting and the evolution of the production and wall control blast designs from 1997 to 2000. The initial blast designs and the rationale behind subsequent changes that took place are presented along with the techniques currently in use.The paper also briefly presents an experiment done to measure the rock mass response to blasting. Three blasts were instrumented with geophones, gas pressure sensors and time domain reflectometry cables. A brief summary of the instrumentation and data gathered is included."

Jan 1, 2001

By E. Nolasco, J. Ouellet, T. Tikka

"Shaft bottom structural systems are used in underground mining to support transfer of personnel, equipment and ore to and from underground to the surface. This paper first summarizes the evolution of design philosophy from a concrete tower supported on a concrete plug to the current structural steel design arrangement with unlined shaft walls, clear shaft bottom area with only a concrete housekeeping pad. Then the paper reviews the design parameters, analysis and design, and construction methodology for this rather unique shaft bottom structural system consisting of three sets of hitch beams, with each having specific functional requirements. INTRODUCTION Shaft bottom structural systems are used throughout the world in underground mining operations to provide a means to support the transfer of personnel, equipment, materials, ore and waste entering and exiting a vertical shaft ready for transport to and from the surface via the hoisting system. The shaft bottom structural system, for the Service Shaft (SS) at the Jansen Mine, is designed to accommodate two skips, a personnel/equipment cage, counterweight, services, loading pocket, rope changing, arrestor system, crash (or catch) beams, access platforms, stairs and rope divider system. Stantec and BHP have engineered a unique structural steel shaft bottom system for hoisting system at a Potash Mine. The shaft bottom structural system connects to a fixed guide and cantilever bunton system, used in the vertical shaft (shaft barrel), above the shaft bottom. The geometry for the shaft bottom structural system, shown in Figure 1 a), features three sets of hitch beams, beams which span across the shaft excavation or barrel. At the top of the structural system are two upper hitch beams. These hitch beams support a 64 metre suspended rectangular braced tower (upper tower), complete with steel guides for the conveyances. The upper tower passes through the main station (potash or mining) level and then connects to the top of the arrestor (lower) tower structure via a sliding vertical connection. The potash level is supported by two hitch beams spanning the shaft and loading pocket excavations. The arrestor tower, a braced compression tower structure, is carried by a third set of hitch beams. Below the third set of hitch beams is a short suspended tower complete with access platforms, stairs and the rope divider system."

Jan 1, 2019

By P Hulteberg

In this article, an integrated catalytic reactor design approach to produce PEMFC-quality hydrogen is evaluated. The design is based on a high level of heat exchanging perfonned internally, highly active noble metal catalysts and a woven wire mesh catalyst support system. It consists of an integrated steam refonner and a catalytic burner section, a water gas shift section and a preferential carbon monoxide oxidation section. The reactor design is described and experiments perfonned to evaluate the two reactors built are reported. The two reactors have a maximum output of 3 Nm and 10 Nm3 hydrogen/h respectively. In the larger unit, a total of six fuels, three gaseous (methane, natural gas and liquid propane gas) and three liquid (naphtha, ethanol and methanol), were evaluated. The larger unit was also used to investigate how variations of parameters such as steam-to-carbon ratio in the steam reforming part of the system and the relation between oxygen and carbon monoxide in the preferential carbon monoxide oxidation affect the reactor perfonnance. The smaller unit was used, after implementing automatic control, to run a system life time test for 480 h. The refonner system perfonned according to specifications on almost every aspect.

Jan 1, 2005