Search Documents

By J. Dubinski

Underground mining of copper ore in the Legnicko-Glogowski Copper District basin generates a number of seismic events, whose energy often exceeds 108 J (Butra, 2010). The number of tremors and their location shows that the area of rock mass involved in the deformation and failure processes significantly exceeds the area of mining operations. Locations of seismic foci of high energy tremors, as well as the aftershocks that accompany them, extend hundreds of metres, confirming that processes to restore the energy balance of rock mass occur in a short amount of time and over a wide area. Thus, an area of similar size should be considered in predictive analyses of the tremor?s position. It should be emphasized that a large portion of the rock mass still has a level of freedom resulting from the way the rock mass is held together and its geometric continuity. This level of freedom is dependent on the scale and duration of mining, the number and size of natural structures, and rock mass pressure, including gravitational pressure constricting individual fragments of rock mass in the area (Burtan, 2012). It can therefore be assumed that in real conditions, areas where mechanical strength of the layers has been exceeded may be located a considerable distance from each other and do not necessarily need to coincide with the working area location. In this sense, a rock mass influenced by mining exploitation is essentially a rock mass in which numerous fragments with concentrated energy exist simultaneously. Energy will be released within these rock mass areas each time rock mass strengths are exceeded by the induced stress changes related to mining operations. This paper presents a discussion on how to predict the location of seismic activity areas based on a change of position of seismic energy equivalents. This parameter is calculated for a given set of seismic tremors with defined foci coordinates. For a given set of seismic tremors, the location of seismic energy equivalents may be used for predicting the location of high-energy seismic events.

Aug 1, 2013

By T. A. Utigard, S. Pedler

Ilmenite from the Everett deposit in Quebec was characterized both chemically and mineralogically. The sample investigated contained the following main components: 40% Fe2O3, 21% TiO2 and 21% SiO2. The ilmenite grains contained about 20 to 25% hematite intergrown blades, with widths ranging from 2 to 30 \u03bcm. Crushing the sample to less than 0.85 mm led to significant liberation of the ilmenite from the gangue minerals. Gravity separation followed by magnetic separation of this size fraction led to a TiO2 concentrate grading of about 30% TiO2, with a recovery of 94%.

Jan 1, 2010

By R. D. Brown

"Finance Minister Donald Macdonald's budget of May 25, 1976 featured a restructuring of the anti-inflation profit controls and a grab bag of tax changes, some of direct interest to the mining industry. All Canadian taxpayers now will be permitted to write off immediately 100% of mineral and oil and gas exploration expenses included after• May 25, 1976 and before July 1 1979. The cost of acquitting Canadian resource property after May 6, 197.4 from a federal or provincial government will now clearly be included in Canadian development expense, and provincial drilling and exploration incentives received after May 25, 1976 will not reduce exploration and development expense for federal income tax purposes. Under tough new anti-inflation profit controls, all controlled businesses, except distributions, will essentially have one uniform set of rules for• determining allowable profit margins; this allowable margin will be determined by product line or by over-all net margin and will be 85% of the higher of the margin obtained in the five years preceding October• 13, 1975 or the one year preceding May 1, 1976. The basic capital cost allowance system is to continue, but many rates will be revised. The ability to offset losses created through claiming capital cost allowances on leased equipment, etc. against other income will be ended with respect to transactions entered into a/te1• budget night. Miscellaneous other tax changes will raise the low rate base for Canadian-controlled private corporations to $750,000 increase retitement plan contribution limits and reduce the rate of branch tax imposed on branches of corporations resident in a country with which Canada has a comprehensive tax treaty to equal the withholding tax rate on dividends under that treaty."

Jan 1, 1976

By Gillyeard J. Leathley

The Cassiar Asbestos mine is situated on McDame Mountain in northern B.C. at a mean elevation of 6000 ft (1830 m), some 6 miles (9.6 km) from the townsite /mill complex. Asbestos ore production averages 1,200,000 tons at 9% R.M.G. (Recoverable Mine Grade) and waste production is 6,000,000 cu. yd annually. Waste is loaded by P&H 1900 AL 11-cu.-yd shovels and transported by 75-ton and 85-ton end-dump trucks to the waste dumps. The ore is loaded by a 992 Caterpillar 10-cu-yd front-end loader into 50-ton and 75-ton trucks, which transport it to the crushing plant located at the mine. The ore is transported by a 15,370-ft (4685-m) tramline to the mill complex.

Jan 1, 1978

By J. Petit

"In July 2004 workers at the ABI Smelter in Bécancour (Quebec, Canada) went on strike. Contingency plan were ready to face the situation and plan was done to operate one potline out of three. Two lines were stopped; keeping in mind the restart on cold metal after the strike was over. The subject to be presented and shared includes a summary of work organization including training, schedule of restart, pot cleaning, pot preparation, crash start method, follow up after crash start, safety and environment. This major project has been a very big challenge. It shows that people involvement is a must and the key success. It is then true to say : ""People who believe in success will work and act in order to get there"" and ""People who don't believe in success will act in such a way to fail"" Then both will prove they were right to think their own way ! Sharing such experience can be interesting because it's a true story and people like true stories."

Jan 1, 2006

By S. Bastola, Y. P. Chugh

"This research determines shear strength and stiffness properties of bedding planes and joints in the roof strata rocks within 7.5 to 9 m (25-30 ft.) overlying the Illinois #6 coal seam (within the pressure arch zone). A shear test loading device was designed into a 1.334 kN (150 t) Forney Compression Loading Machine to perform direct shear tests in accordance with ASTM D5607-08 “Standard Test Method for Performing Laboratory Direct Shear Strength Tests of Rock Specimens under Constant Normal Force”. The data were used to determine peak and residual friction angles and the dilation angle. A total of 49 bedding plane samples were tested, out of which 46 (36 intact and 10 relatively weak and loose) samples passed QA/QC procedures in accordance to ASTM D5607. Samples from eight (8) different bedding planes- shale/limestone (SL), shale/sandstone (SSs), shale/bone (SB), laminated sandstone (LS), shale/shale (SS), bone/bone (BB), bone/limestone (BL), and limestone/limestone (LL) were tested. The number of samples tested for each bedding plane were: SL- 11, SSs- 8, SB- 5, BB- 4, LS- 6, SS- 9, BL- 1, and LL- 2. Peak and residual shear strength values at 2.75 MPa normal stress range 1.06 – 6.26 MPa and 0.82 MPa to 0.82 – 4.14 MPa, respectively. The average normal and shear stiffness values are about 11.98 GPa/m and 3.11 GPa/m. Dilation angles are low (<10?) and negative in some cases. Angle of sliding friction values range from 9? to 42?. Joint Roughness Coefficient (JRC) values were less than 10.INTRODUCTIONRock mass may be defined as the total in situ rock medium containing bedding planes, faults, joints, folds and other structural features. Therefore, it is discontinuous and may have heterogeneous and anisotropic engineering properties. Upon creation of an excavation in a rock mass, bedding planes and joints are the most likely points of failure initiation. The failure typically occurs either in tensile or shear mode. Upon failure initiation stresses are transferred to the neighboring rock mass and the failure progresses until stability is achieved through equilibrium of stresses and strength. An example of this mechanism is development of the pressure arch. This study determined the shear strength and stiffness properties in shear and compression of bedding planes and joints in the immediate roof strata rocks within 7.5-9 m ( 25-30 ft.) overlying the Illinois No. 6 coal seam (within the pressure arch zone). Since such data are currently not available for Illinois Coal Basin mines, researchers and engineers have been using estimated values for design purposes. The immediate roof lithology in the proposed mining area consists of shale 0.62 m; Bone 0.09 m (0.3 ft.); Limestone, 0.10 m (0.33 ft.); Shale 2.37 m (7.9 ft.); and sandstone 0.55 m (1.83 ft.). The bedding plane samples were provided by a mine in south-eastern Illinois operating at a depth of about 180 m (600 ft.)."

Jan 1, 2015

By W. L. Sherwood

Present conventional techniques for primary steelmaking in both integrated and non-integrated plants are outlined. 'Direct reduction' alternatives are reviewed and categorized according to the nature of the product produced, with particular emphasis on the limited number designed to yield steel as the end product. A proposed new technique, referred to as the Sherwood Process, is described in some detail as a new combination of selected features from the prior technology. This process is in-tended to realize, in integrated operations, the result of continuons steelmaking directly from the ore in a single plant and, in non-integrated operations, continuons steel-making from a metallic charge of scrap, sponge iron or pig iron. Prominent features are continuons processing in elongated, horizontal, rotary furnace equipment, controlled direct heating of each process stage and, for the over-all integrated process, a size separation for removal of excess solid reductant and other waste just prior to the melting step. Material and energy balances are presented as well as exemplary cost data. Reasons for selecting this particular combination of process elements are dis-cussed.

Jan 1, 1968

By R. W. Culley

"In many areas of Saskatchewan, known gravel deposits have been depleted or are diminishing rapidly; in other areas, particularly in the north, demands for all-weather highways and access roads are far exceeding the supply of gravel sources with which to surface them. These two problems have made conventional methods of air-photo and ground surveys insufficient for gravel location. In the first case, hauling costs on construction now warrant searching for buried deposits and for smaller, less obvious surficial deposits that may be closer to the project. In the second case, search and access conditions are so difficult and costly that the ratio of successes to failures must be kept very high. The Department of Highways has long been aware of the oncoming scarcity of quality gravel deposits and is continually investigating ways of forestalling it. One of these ways is the use of airborne geophysical methods that permit rapid coverage of large areas and that sense and discriminate between earth properties to a significant depth below ground surface. In 1967, the Department began an investigation of an airborne conductivity survey method called INPUT*, or ""Induced Pulse Transient'', leading to a trial in 1968 and data analysis in 1969. The results of this trial initiated• modifications to the technique to improve its sensitivity for mapping shallow deposits. Part way through this modification in 1970, a decision was made to change to an airborne resistivity survey method called EPHASE*. Trials with this technique were conducted and analysed in 1971. This paper is an explanation of the E-PHASE system and a summary of the results from one of three areas mapped in 1971."

Jan 1, 1973

By K. Janghorban

Multilayered ceramic-metal composites were produced by solid state diffusion bonding of polycrystalline alumina and three Al alloys containing 1 to 2%Sr, 2% Mg and Mg + Si (5057 Al alloy), The multilayered structures were fabricated at 610°C under a compressive stress of 3 MPa for 2 hours in He-5%H atmosphere, The ceramic-metal interfaces were studied by SEM and TEM equipped with energy dispersive spectrometer (EDS). Addition of 1 wt % Sr to Al promoted good adhesion, without producing any interfacial products, while the Al-2%Sr was poor in this regard due to the presence of dispersed A14Sr which is an intrinsic phase in the Al-Sr phase system, The Al-2%Mg alloy produced a continuous film at the interface, which was characterized to be MgAl2O4. Al alloys containing Mg and Si (5057 commercial alloy) produced not only the spinel structure (MgAl2O4), but another phase rich in Mg and Si (close to Mg2Si), These latter interfacial reaction products were not the intrinsic phases in Al-Mg alloys, and were reaction products at the Al2O3 ?Al alloy interfaces.

Jan 1, 2005

By P. Scinto, P. Hudson

"Modern day ore bodies are becoming increasingly harder, more abrasive and lower grade. The Mako deposit is located in Senegal and consists predominantly of primary mafic and felsic lithology that are both very competent and very abrasive ores (Axb < 30, BWi >20 and Ai >1.0). The deposit was initially discovery in 2010 and the Toro Gold management team fast tracked the Mako Project through development and into production to achieve its first gold pour in January 2018. The comminution circuit comprises primary crushing single stage SAG milling with recycle crusher (1oCR SS-SAC). The mill reached design throughput and grind size seven weeks after first ore. The Mako project marks another successful international application of single stage milling, which represents a simple and easy to operate comminution circuit for small-to-mid size projects with a low capital cost. This paper describes the ore interpretation, comminution modelling, grinding circuit selection and design, as well as an overview of the commissioning and ramp-up of the mill.INTRODUCTION The Mako Gold Project is operated by Toro Gold Ltd., which holds a 90% interest in the project. The project is located in south-eastern Senegal in the Kedougou region, close to the Gambia river and township of Mako. The Mako deposit lies in the “Kenieba Window” of eastern Senegal and western Mali, which hosts a number of gold mining operations and development projects. The Mako Gold Project has an estimated life of 8 years with overall recoverable gold estimated at 924 koz. The process plant is designed to treat 1.8Mt/a of ore and produce 128 – 143 koz of gold per annum. Lycopodium Minerals Pty Ltd (Lycopodium) was appointed to provide feasibility studies and EPCM services for the greenfield project. Forming part of consultancy services provided by Lycopodium, Orway Mineral Consultants (OMC), a subsidiary of Lycopodium, was involved in the design, commissioning, ramp up and ongoing post commissioning support of the comminution circuit."

Jan 1, 2019

By M. A. Rabah

This study aims to recover europium, yttrium metals, some valuable salts or oxides from the white powder (apatite) coating the inner surface of spent florescent lamps (SFLs). Pressure leaching using sulphuric/nitric acid successfully dissolved the metals of interest. Europium or yttrium metals were obtained by hydrogen reduction of their oxides. Addition of potassium thiocyanate converted the dissolved sulphates to thiocyanates. Selective separation of Eu and Y was then carried out by solvent extraction from the thiocyanate solution. The used solvent was trimethyl-benzylammonium chloride. N-trihutylphosphate in 1 M nitric acid was used to strip the metal loaded in the organic phase. Results showed that the quality of the cleaned glass tubes of the SFL met the standard requirement for the lamp manufacture. The white powder (WP) is composed of calcium sulphate 35.2%, phosphate 61.5% and oxides of europium and yttrium 1.65%wt. respectively. Autoclave digestion of the WP for 4 h at 120°C and 500 kPa in sulphuric acid/nitric acid mixture dissolved 96.4% of yttrium and 92.8% of europium. The conversion rate of sulphate to thiocyanate was favoured at low temperature. Stripping of Eu and Y from the loaded organic phase behaved in an opposite way. A metal separation factor of 9.4 was obtained. ate recovered europium and yttrium salts were selectively separated using ethyl alcohol or dilute nitric acid. Yttrium was very soluble while europium was not. Europium and yttrium metals were obtained by hydrogen gas reduction at 850°C and 1575°C respectively.

Jan 1, 2004

By J. J. Hussey

"Abstract-The ""Brunswick Horizon"" an informally named ore-bearing unit near the top of the Nepisiguit Falls Formation in the Ordovician Tetagouche Group, hosts the Brunswick No. 6 and No. 12 base-metal mines, as well as the former Austin Brook iron mine, in northern New Brunswick. Detailed structural analysis of the No. 6 and No.12 mines led to the prediction that a massive­ sulfide deposit may have been repeated by F1 folding along the Brunswick Horizon. A subsequent drilling program discovered the new massive-sulfide North End Zone at a vertical depth of 1100 m, 1 km north of the No. 12 underground workings. By the end of 1990, Zn-Pb-rich massive sulfides had been delineated over a strike length of 200 m and a down-dip extent of 170 m. Rock units intersected in the North End Zone are generally thinner and vary somewhat from those at the Brunswick No. 12 mine. Thinning of the hanging wall rocks may be primary, may result from attenuation along F2 folds, or may represent truncation by a thrust fault. The newly discovered sulfide zone indicates that significant potential exists for the discovery of other deposits at previously unexplored depths.SOMMAIRE-Dans le nord-est du Nouveau-Brunswick ""l&apos;horizon Brunswick"" est le nom usuel de la zone qui contient les mines de métaux de base Brunswick No. 6 et No. 12, ainsi que l&apos;ancienne mine de fer Austin Brook, toutes situées sur le dessus de la Formation ""Nepisiguit Falls"" dans le Groupe Tetagouche d&apos;âge Ordovicien. Une analyse détaillée de la structure des mines No. 6 et No. 12 à permis a van Staal de prédire qu&apos;un gîte de sulfures massifs pourrait se répéter dû à une déformation F1, au nord de Brunswick No. 12. Suite à un programme de forage, la nouvelle zone de sulfures massifs appelée le ""North End Zone"", profonde de 1100 rn, et à une distance d&apos;un km au nord des chantiers souterrains, fut découverte vers la fin de l&apos;année 1990, les sulfures massifs riches en Zn-Pb ont été délimités sur une longueur de 200 rn et une hauteur de 170 rn le long du pendage. Les unités de roches intersectées dans le ""North End Zone"" sont généralement plus minces et sont quelque peu différentes de celles de la mine Brunswick No. 12. L&apos;amin­ cissement des roches pourrait être primaire ou être le résultat de l&apos;atténuation le long des plis F2, ou soit tronqué par une faille. La nouvelle découverte d&apos;une zone de sulfures indique un potentiel énorme pour la découverte d&apos;autres g ""tes à ces profondeurs inexplorées."

Jan 1, 1992

By B. D. Pandey, M. S. Kim, B. S. Kim

The recovery of Sn from used Pb-free solder (Sn, 3~4 % Ag, < 0.9 % Cu, < 1.2 % Pb) has been investigated by electrorefining in sulfuric acid solutions containing small amount of hydrochloric acid. This involved preparation of the anode material by melting and casting the used solder followed by refining. During electrorefining, dendritic tin was deposited on stainless steel cathode. Increasing the amount of hydrochloric acid up to 0.3 mol /L in the electrolyte enhanced the current efficiency to 92.2 % and the enrichment ratio of silver to 94.3 % in the anode slime which was otherwise 84.7% and 81.6 % in absence of HCl, respectively. The electrolyte containing hydrochloric acid has also prevented the precipitation of tin oxide in the bath. In the scale-up experiment using 1.6 kg anodes, 84.3 % current efficiency and close to 100 % Ag enrichment ratio were obtained, while the purity of electro-refined tin was over 99.9 %. The energy consumption of the winning process was found to be 0.151 kWh /kg-Sn which is competitive as compared to commercial tin electrorefining processes.

Jan 1, 2014

By Jeanne B. Percival, Paul Ramaekers, Charles W. Jefferson, Pat A. Hunt, Eric G. Potter, Katherine E. Venance, William Davis, Sean A. Bosman

"A 10-cm thick clay-rich layer near the top of the Manitou Falls Formation of the Athabasca Group is unusual in its breccia texture, alteration, and detrital mineral composition relative to the adjacent overlying and underlying sedimentary beds. This layer is composed of angular quartz grains set in an illite >> kaolinite + dickite matrix. Deformed clay-rich fragments within the layer have very similar mineral assemblages. The presence of euhedral accessory minerals including Ti-oxides and aluminophosphatesulphate minerals points to a diagenetic/hydrothermal origin. The presence of individual grains of Kfeldspar and amphibole is unusual relative to the typical Athabasca quartz arenite; originally, these minerals were probably included in detrital quartz and subsequently liberated during fracturing. The textures and alteration characteristics suggest that this layer is a hydraulically-fractured unit, which has experienced hydrothermal fluid alteration - a possible pathway distally related to uranium mineralization Une couche argileuse de 10 cm d’epaisseur pres du sommet de la Formation de Manitou Falls du Groupe d&apos;Athabasca est remarquable par sa texture brechique, son alteration et la composition de ses mineraux detritiques qui different de ceux des couches sedimentaires sus- et sous-jacente. Cette couche est composee de grains de quartz angulaires dans une matrice composee d’illite >> kaolinite + dickite. Des fragments deformes riches en argile dans cette couche presentent des assemblages mineraux tres similaires. La presence de mineraux accessoires idiomorphes dont des oxydes de titane et des aluminophosphates-sulphates suggere que ces derniers ont une origine diagenetique / hydrothermale. La presence de grains de feldspath-K et d&apos;amphibole est inhabituelle comparativement aux arenites quartziques typiques de l’Athabasca; initialement, ces mineraux constituaient probablement des inclusions dans le quartz detritique qui ont ete subsequemment liberees pendant la fracturation. Les textures et les caracteristiques de l&apos;alteration suggerent que cette unite a subi une fracturation hydraulique et a ete alteree par un fluide hydrothermal - possiblement en lien avec les effets distaux de mise en place de la mineralisation en l&apos;uranium."

Jan 1, 2013

By Arthur Dubé

An account is given of the developments brought about in the last fifteen years by metallurgical research in the field of heat treatment of steels. The practical aspects of these developments are especially emphasized. Methods of representation of the phase-change during austenitizing and sub-critical transformation of austenite are described and the importance of time-temperature-transformation charts for the planning of heat treatment cycles is shown. Special copies such as retained austenite and internal stresses developed on quenching are also discussed in some detail. Due to the interest shown currently in these problems, it has been thought advisable to describe briefly the underlying principles and present some of the results already available.

Jan 1, 1945

By W. D. Madeley

Synthetic minerals were made from pure starting materials and galena samples were doped with the title metals. Microscopic, microprobe and X-ray examination confirmed that the dopeants were in solid solution. Paired flotations in a Hallimond-tube apparatus were performed to determine relative flotation response using Aerofloat 238 promoter. Results of these tests show that silver-doped galena floats more readily than pure galena and that galena doped with bismuth floats less readily than pure mineral to a 95% confidence level. Galena doped with both silver and antimony as AgSbS2 shows no detectable effect. Antimony-doped galena followed the expected trend, but not to 95% confidence. The results are consistent with the theory that flotation by thiol-type anionic collectors is enhanced by p-type semiconduction.

Jan 1, 1978

By D. E. Parson, W. A. Morgan

This paper offers a brief review of current literature pertaining to vacuum degassing or vacuum casting of steel as practiced in the U.S.A., Germany and the U.S.S.R. The advantages of vacuum degassing of large forging ingots, heavy section casting, for the conversion of rimming bessemer steels to killed steel and for the production of transformer steels are discussed. Operating pressures, reduction in gas contents and improvements in hydrogen segregation, steel cleanliness and mechanical properties, obtained with the various techniques, are described. The paper includes a description of an experimental vacuum stream-droplet degassing unit and some preliminary results obtained at the Physical Metallurgy Division Research Laboratories Department of Mines and Technical Surveys, Ottawa on laboratory steel melts. Experimental 500 lb direct arc, basic melts have been spray cast into either ingot moulds or dry sand moulds, held inside a vacuum tank. Also 500 lb melts have been

Jan 1, 1961

By A. F. Brock

Introduction During the past ten years, shaft sinking has been going on continuously at Inco and new shafts and shaft extensions have been sunk under a broad diversity of conditions. The Murray mine and the Stobie section of the Frood-Stobie mine have?been opened and a main hoisting and supply shaft has been sunk at each of these mines; No. 2 shaft at Murray was sunk initially from surface to 1,960 feet and is now being extended; No. 7 shaft at Stobie was sunk from surface to 3,105 feet. No. 2 shaft at Garson has been extended from 2,200 feet to 3,200 feet in depth. At Levack, No. 2 shaft is being extended from 1,860 feet to 2,850 feet for ore hoisting from the 2,650 lev el. At Creighton, No. 6 shaft, collared on 52 level, was sunk 1,740 feet to a total depth of 5,563 feet below surface. It is the deepest Inco working. At Creighton, also, No. 7 shaft is being sunk from surface to the 30 level to handle the ore from caving operations. Ail Inco main hoisting and supply shafts sunk during the past twenty years have been vertical rectangular shafts equipped with two cages and two ore skips. The cages are standard and interchangeable for all shafts except Garson No. 2; they are single-deck, 13 ft. 4 in. by 5 ft. 2 in. inside and are designed to carry a maximum material load of 16,000 lb. The man load is 48 men. Skip capacities at the several shafts vary from 8 to 15 tons. Forty-two hundred feet bas been established as the standard vertical lift, and the permanent hoisting equipment at each shaft is designed for eventual hoisting from that depth.

Jan 1, 1950

By Z. Y. Liu

A local additional potential model (LAPM) was developed to illustrate the role of strain rate in stress corrosion cracking (SCC) of pipelines. According to LAPM, both density and mobility of the local active spots on the steel surface, i.e., dislocation emergence points, increase linearly with strain rate. Generation of such active spots introduces an additional negative potential locally, affecting the electrochemical reaction and, consequently, the susceptibility of the steel to SCC. Electrochemical corrosion measurements, slow strain rate tests and electrochemical hydrogen permeation test were combined to demonstrate the validity of LAPM to illustrate pipeline SCC in an acidic soil solution. It is found that a maximum of the SCC susceptibility occurs at strain rate of 10-6 s1, which is associated with an enhanced hydrogen evolution due to the local additional potential (LAP) effect.

Jan 1, 2010

By O. G. Olvera

"Refractory sulfidic ores consist of materials in which gold occurs finely disseminated within metallic sulfides or forming solid solutions, with pyrite and arsenopyrite being the two sulfides most commonly associated with gold. Typical cyanide operations show poor performance and require oxidative pretreatments to increase gold recovery. Pretreatment alternatives include roasting, pre-aeration, acidic and alkaline high pressure oxidation, and bacterial oxidation. The presence of arsenic, however, introduces a serious disadvantage to the use of roasting and bacterial leaching, while high pressure oxidation involves high capital costs. This work focuses on evaluating the effect of the addition of a carbon resin as a sulfur collector on the oxidation of different arsenopyrite concentrates under atmospheric tank leaching (ATL) conditions. The addition of the resin improved the oxidation of sulfides and favored the formation of elemental sulfur over the generation of sulfate. The use of AF5 in ATL resulted in higher gold recoveries under standard cyanide carbon-in-leach and thiosulfate leaching.INTRODUCTION Refractory sulfidic ores consist of materials in which gold occurs finely disseminated within metallic sulfides or forming solid solutions, with pyrite and arsenopyrite being the two sulfides most commonly associated with gold. Gold is not readily accessible to solutions in these types of ores and typical cyanide operations show poor performance, thus making the use of oxidative pretreatments a requirement to increase gold recovery. Pretreatment alternatives include roasting, pre-aeration, acidic and alkaline high pressure oxidation, and bacterial oxidation. The presence of arsenic, however, introduces a serious disadvantage to the use of roasting and bacterial leaching, while high pressure oxidation involves high capital costs. The use of carbonaceous materials to enhance the dissolution of sulfides is not novel, and leaching additives such as coal, activated carbon and carbon powder have been considered for the improvement of bioleaching, atmospheric leaching, and pressure oxidation leaching processes. However, this type of technology has been focused mainly on the recovery of copper from copper concentrates containing chalcopyrite with less attention paid to other sulfides."

Jan 1, 2017