Search Documents

By A. Ojaghi, A. R. Mohammadi

"The Marvast monazite deposit is located 35 kilometres south - southwest of Marvast in Yazd province of Iran. A representative sample weighing approximately 10 tons was prepared to study the amenability of the ore to physical beneficiation. The size fraction of +1000 µm was removed due to low monazite content and the –1000 µm size fraction was concentrated by the gravity-classification-magnetic methods. According to the results of sample characterization, the representative sample contains 220 ppm REO that is contained in monazite. It was concentrated to 41.5% REO by the above mentioned methods. The recovery of REO in the monazite concentrate was 41.5%.INTRODUCTIONRare earth elements are critical metals in many countries (Gupta, 2005; UK Geological Survey, 2011). Increasing application of these metals in hi-tech industries and price fluctuation caused by Chinese production policy has led other countries to focus on their local resources (UK Geological Survey, 2011). In this case, Iran is not an exception.REE mineralization in Iran is mainly located in the central zone. Regarding the exploration data, these deposits are divided into two categories. The first group is iron ore deposits in which the REE are carried by phosphate minerals. The other group is placer deposits where monazite is the major mineral of the deposit. The Marvast placer deposit is one of these types of deposit (Daliran, 1990; Mokhtari, 2008; Torab, &Lehmann, 2007; Alipour, 2014)."

Jan 1, 2016

By T. Gerritsen, R. MacRosty, R. Pula, P. Gebski, W. L. Ying

Furnace run-outs can cause extended furnace downtime for repair, while leaks or more severe failures in the cooling system can lead to brick hydration or in severe cases, steam explosions. These incidents can result in lost production, damage to equipment, injuries and casualties. To prevent such incidents, reliable and accurate techniques to monitor the critical components of the furnace such as refractory lining, furnace structure, taphole integrity and main water circuits are required. This paper describes several advanced methods that have been developed to assess the condition of furnace integrity, refractory lining, tapholes and cooling water circuits.

Jan 1, 2015

By Fatemeh Saeidi, Luis Marcelo Tavares, Malcolm Powell, Mohsen Yahyaei

"Understanding a single breakage mechanism is fundamental to the development of breakage testing techniques appropriate for mechanistic modelling of any breakage equipment. In the light of this insight, it is also possible to compare any two breakage events in a mechanistic manner. This paper presents a new method to compare breakage mechanisms of two-point impact with compression, different in their applied strain rates. This approach regards a single breakage event as a process affected by three sub-processes; first fracture, capture and spatial distribution of fragments. Spatial distribution is influenced by the kinetic energy of fragments and their brittleness. Using this methodology allows us to examine how each sub-process is influenced by applied strain rate and its impacts on progeny size distribution. For this purpose, two rock types of widely different strength, magnetite and silicate, were tested at various energy levels using the impact and compression mechanisms. To isolate the effect of spatial distribution of fragments, particles were forced to remain in the breakage zone. In this condition, similar progenies were generated from compression and impact mechanisms at similar energy levels. However, allowing natural distribution of fragments, coarser progeny was produced from compression of silicate. Additionally, using this approach provides a physical meaning and explanation for rock strength parameters such as A×b in the t10-Ecs relationship. INTRODUCTIONComminution models are rapidly progressing toward a destination that enables us to explain the complete physics of a breakage process as well as the properties of the ores. Eventually, they will be able to take into consideration the micro-events that take place during the comminution process (Bourgeois and Banini, 2002). Thus, considerable efforts have been made in the last few years in the area of ore breakage characterisation to comprehend and unlock a single breakage process that has been treated as a black box event in the majority of conventional methods. In this paper, an attempt is made to explain the effect of applied strain rate on the breakage properties of rock by using the knowledge that has been gained by understanding a breakage event. This is particularly important due to its application for various comminution devices that operate within a relatively broad range of speed."

Jan 1, 2016

By D. B. Smith

DURING the summer of 1953, test work commenced at the Sullivan Concentrator with a view to the modification of filtration practice by the inclusion of wet cyclone classification of the lead concentrates, with separate filtration of the underflow and overflow products. Formerly, practice was conventional and the equipment employed comprised one 50-foot diameter thickener ?with the underflow routed via a 20-foot stock tank to two 8-foot by 12-foot Oliver filters. Heating of the filter feeds to 40° C. and the use of mechanical slappers on the filter drums ?have both been standard features of Sullivan practice for years. Both of these have been retained. Currently (February, 1956), lead concentrates are being classified into sands and slimes by 12-inch cyclones with the underflow, at 75 per cent solids, being fed to No. 1 Oliver filter. The overflow is thickened to 75 per cent solids and filtered separately by a No. 2 Oliver filter . The tonnage split is approximately two of underflow to one of overflow. The overflow contains 75 to 80 per cent of the total minus I 500 mesh slimes in the feed.

Jan 1, 1956

Mining Equipment Challenges Equipment Availability Unplanned downtime Maintenance Costs Secondary damage and catastrophic failures (T282 $750k) Emergency work is 4x the cost of planned work Inspections Troubleshooting time Incorrect repairs (parts, labor, lost production) Equipment Life Mis-operation of equipment

May 1, 2013

By Patrick E. Cavanagh

"A pilot shaft furnace was operated for one year at Steep Rock to produce special high-grade products from coarse ore, using lignite as fuel. The furnace is 10 ft in diameter and 60 ft high. When operated to heat coarse Steep Rock ore to drive off combined water and give a 64-per-cent-Fe product, the fuel consomption was 900,000 Btu's per long ton of product. The furnace was run in this way from September 1966 to January 1967 to establish the technique of feeding and discharging the furnace and controlling the gas composition and temperature. The furnace is similar in operation to a lignite water gas producer containing a large proportion of catalytic iron oxide. Steam injection is used to control the temperature. The product was tumbled in a rotary trommel to stabilize it. The resulting fines could be fed to the conventional pellet plant at Steep Rock. The furnace was next operated to make 77-per-cent-Fe metallized coarse ore. Several major modifications in de-sign were made and the furnace was successfully operated for short periods to maintain the required conditions to remove 75 per cent of the oxygen from the ore to give a 75-per-cent-reduced product at a grade of 77 per cent iron. The furnace cooling zone was operated under positive pressure, with internai alkaline water sprays to cool the charge. The product was discharged from the open bottom of the furnace without serions reoxidation. The metallized ore was magnetically separated from the discharge. Most of the charred lignite discharged along with the ore is re-cycled. Fuel requirement was 11,000,000 Btu's per long ton of product. This metallized coarse ore is intended for blast furnace feed. A short test run was carried out to establish the conditions for making a highly reduced melting stock for steel furnaces. To achieve 90 per cent reduction and over 90 per cent Fe, the furnace must be slowed down so that the production rate is about one-half the rate when making a 75-per-cent-reduced metallized product. Fuel requirement is 15,000,000 Btu's per long ton of product. The simple shaft furnace developed is similar to the top half of a blast furnace, with some major modifications to allow discharging into the open air. This Low Temperature Blast Furnace program has been technically successful and has resulted in making data available for the design of a commercial plant. Study of the commercial feasibility of large-scale production of metallized coarse ore at Steep Rock is still continuing."

Jan 1, 1968

By Y. F. Jiang, K. Fang, Q. Q. Jiang, Q. Wu

Inter formational sliding of bedding planes between two different rock types in Badong formation is an important reason that leads to the instability and fracture of rock mass in this stratum. There are no specific research achievements on bedding planes between two different rock types in Badong formation. In order to study the shear mechanical properties of bedding planes between two different rock types. This paper using the software of particle flow code (PFC) and JRC model to establish several typical structures of different roughness coefficient of surface morphology based on the laboratory tests on silty mudstone and marlite in Badong formation. A great deal of numerical shear tests were carried out by ball production, radius expansion and servo infliction. The research results are as follows: First, shear strength of Badong formation is found to vary between that of silty mudstone and marlite isotropic planes by analyzing shear strength of the homogenous bedding planes and inhomogeneous rock types, we can find that the shearing strength in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the shearing strength of silty mudstone isotropic planes. Second, the basical friction angle of bedding planes between two different rock types in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the basical friction angle of silty mudstone between isotropic planes. Third, based on the experimental results, an expression is obtained to describe the relationship of the ratio of shearing strength between bedding planes of two different rock types and isotropic planes in soft rock, the rock combination coefficient, and the roughness coefficient. This study has important significance for further research on the shear mechanical properties of bedding planes between two different rock types.

Jan 1, 2015

By D. W. MacFarlane

In the formation of Oil and Gas Producing Units lawyer& and engineers are interdependent members of the same team. Management is, there-fore, entitled to expect no less than a total cooperative effort from the members of these professions. The petroleum and natural gas lawyer must diligently inform himself on the implications of engineering evidence. Otherwise he can be of little assistance to his engineering witness in a thorough, systematic and convincing presentation of his technical evidence. Conversely, the engineer must appreciate the concern of counsel that quasijudical hearings, whether technical or otherwise, be con-ducted in such a manner as to pre-serve some semblance of organized judicial procedures in the adjudication of property rights. The principal problems in unitization are the participation formula and the adjustment of investment in unit facilities. The equating of oil to gas, the effect of unit infill drilling, the relative values of producing zones and well productivity have •been controversial factors in several Saskatchewan units to date. Perhaps the most perplexing of these has been well productivity. While preserving current income, it may also preserve an ability to drain adjacent tracts plus an inequitable sharing of .reserves properly attributable to secondary recovery operations. However, inequity may also result in depriving an operator of the benefits accruing to him under competitive operations by virtue of his favourable reservoir position or his use of advanced production techniques. The Saskatchewan Oil and Gas Conservation Act has been construed by the Department of Mineral Resources as •completely negating any benefits inherent in the rule of capture when determining equities under unit operations. Under adjustment of investment provisions, large cash flows between owners of exploited acreage should be avoided upon the creation of a unit. These provisions should not deprive any company of the benefits it may have obtained under competitive operations in producing its fair share of the reservoir at a lower net cost per barrel than its competitors. Unitization should be concerned with physical conservation rather than in equalizing production costs as between operators.

Jan 1, 1960

By S. R. Stopic

The EU-financed INTREAT Project (Integrated treatment of industrial wastes to¬wards prevention of regional water resources contamination) addresses the environmental pollution associated with solid and liquid wastes/effluents produced by complex sulphide ore mining and metallurgical activities. The results concerning the electrolytic recovery of cop¬per from effluents formed after mixing of streams from Copper Refining, Precious Metals Plant and Electrolyte Regeneration in the Balkan Area will be shown. The waste water is characterized by low pH values and high contents of heavy metals, such as Cu, Ni, Bi, As, Sb. The majority of these waste water flow untreated into the natural water streams and through the network of existing rivers, which end up in the river Danube. The influence of current density and flow rate on the deposition rate, the quality of copper and the process efficiency will be presented. The full continuous process is based on cells with rotating disc cathodes and represents a pre-treatment step before common neutralisation in a cascade line

Jan 1, 2007

By M. O. Pekguleryuz, D. S. Aydin

The high temperature oxidation and ignition resistance of Mg-(0-6) wt% Nd alloys have been investigated via isothermal and continuous heating experiments conducted in air atmosphere. Alloy composition is observed to be effective in low levels (~ 0.5 %) in the ignition temperature (Ti) of the alloys; the Ti of pure Mg increased from 630 °C to 770 °C with 0.5 wt% Nd addition. However, no noteworthy improvement was achieved with further additions up to 6 wt% Nd. The initial microstructure was observed to determine the oxide structure on the surface due to the differing oxidation behavior of the phases (a-Mg + Mg12Nd intermetallics). It has been found that the formation of a Nd-depleted region at the subsurface due to extensive Nd oxidation at the oxide/intermetallic interface lowers the protective ability of the oxide scale.

Jan 1, 2015

By M. Zavvari

Flotation, as with most engineering disciplines, involves testwork. Commonly this means going from lab scale to pilot scale to industrial scale. It is important to conduct tests to identify key parameters and to optimize even at the lab scale. To reduce the number of tests while maximizing the information, it is necessary to use Design of Experiment and Statistical Analysis. In this communication Fractional Factorial Design was used to identify the effect of 7 main factors on barite flotation recovery from jig gravity tailings at the Dorrin Kashan operation. The factors include: pH, collector and depressant dosage, impeller speed (RPM), pulp dilution, particle size and flotation time. By analysis of the output with Minitab software all factors were shown to have an effect. Among the factors, pH and flotation time have an interaction effect but the others have wise effect as an interaction effect and main effect. Finally, reliability tests at pH= 9, RPM= 1000, collector 1 000g/ton, depressant l 750g/ton, particle size 90 µm, flotation time 90 s, pulp dilution 23 % solids, the optimum level of each factor, were done. At the optimum level a barite concentrate with average specific gravity 4.308 g/cm3, average grade 93.72% and average recovery 90.04% was produced from the jig tail.

Jan 1, 2009

WMS an Operation Service and Tool WMS is a the new SNC-Lavalin solution to complete and support your site?s operation. It targets phases in the project cycle including mechanical completion, pre operational verification and commissioning. The goal is to track phases completion and electronically deliver a plan with hand over documents.

Aug 1, 2013

By Greg Yuriy

Over the past two decades, Vale Canada has used discrete-event simulation in a key role to support many underground mining studies. Traditionally, general purpose simulation software was developed for manufacturing and service applications. Not until recently have Mine Designers and Simulation Specialists been able to model the dynamics of underground mining scenarios without extensive manipulation of the inherent tools and entities contained within these simulation environments. This paper discusses Vale Canada?s past experiences with a variety of simulation software, describing model development methods and highlighting some of the lessons learned. The paper concludes with a review of recently considered software and provides a framework of desired attributes/functions for modeling mining scenarios.

Aug 1, 2013

By D. Cronin, A. Plumtree, A. Hosseini

"Crack in corrosion (CIC) linepipe defects are hybrid defects not directly addressed by existing assessment methods. To investigate the collapse pressure of these defects, CIC defects were formed in 508 mm (20 in) diameter, 5.7 mm thick API X52 linepipe. These defects were 200mm long and varied in depth from 3.0 to 3.8 mm. The respective failure pressures decreased from 14.3 MPa for the plain pipe to 7.9 and 6.2 MPa respectively. A standard FAD method was applied to evaluate these defects as equivalent length and depth cracks, predicting the rupture pressure conservatively by 18% on average. However, when assessed as equivalent cracks with a reduced wall thickness corresponding to the corrosion depth, the predicted collapse pressures were more accurate, approximately 14% conservative on average.INTRODUCTIONPipelines are a safe and efficient method for transporting high volumes of oil and gas. However, aging pipelines may experience defects, such as cracks or corrosion. Present approaches include detection, assessment and repair of defects before they may become critical to the integrity of the line. There are different codes and standards for assessing pipeline defects, depending on the type of defect, with API 579 (API, 2000) being the most common code for the assessment of cracks in oil and gas pipelines . Corrosion is commonly assessed using RSTRENG (Kiefner & Vieth, 1989). Other methods such as the Finite Element method and the CPS method (Cronin & Pick, 2002) may be used for crack and corrosion, respectively.At present, there is no specific method or procedure for assessing crack in corrosion (CIC) defects, and as a consequence there is a need to provide an assessment and evaluation of the integrity of these defects in order to determine the requirements for defect repair or hydro line testing. Hence, the goal of this study was to provide guidance for the assessment of CIC defects for linepipe.CRACK IN CORROSION DEFECTS (CIC)Significant amounts of corrosion and cracking are not generally found together (Hosseini, 2010). However, a new hybrid defect including cracking within corrosion (CIC) has been identified in operating pipelines. In this case, cracking coincident with corrosion (schematic shown in Figure 1) provides the motivation for the current study."

Jan 1, 2012

By J. Zachwieja

As part of a general review on study of surfactant blinding agents to improve gold recovery during cyanide leaching of carbonaceous gold ores, processes of CIL and RIL leaching using surfactants were investigated. When refractory ores were treated by surfactants, CIL and RIL leaching processes yielded significant improvement on gold recovery. This paper will discuss and compare the laboratory results from two different leaching processes on preg-robbing ores, as well as, illustrate the difference of potential fouling of the blinding agents on activated carbon and resins.

Jan 1, 2015

By W A. James

The use of spectrographic semi-quantitative analysis has recently been of considerable value in establishing the geological relationships in a complicated orebody. The principal minerals found in the Mount Pleasant orebody are cassiterite, stannite, sphalerite, molybdenite, wolframite, chalcopyrite and galena, associated with arsenopyrite, pyrite and fluorite. In addition to the large number of minerals, a further com-plication is the non-uniform distribution of the economic minerals, with one mineral being the only one present in major amounts in one area and another mineral being predominant in another area. At the same time, all minerals are present to a minor extent throughout the deposit. This heterogeneity made it advisable to analyse all exploration samples thoroughly. Analysis by conventional means would have resulted in prohibitive costs. By the use of emission spectroscopy, however, it was possible to obtain, quickly and relatively inexpensively, a reasonably comprehensive picture of the orebody un-der investigation.

Jan 1, 1963

By Keith Spence

"The notion of ""value"" has always been a subjective and contentious issue. Indeed, Value is in the eye of the beholder. There are varied methods and practices for valuing property, as there are industries in which they are applied. For example, there are ""replacement value"", ""insurance value, ""salvage value"", ""appraised value"", ""book value"" and ""fair market value"", to name a few, although in the mining industry, valuations usually refer to fair market value.In the Canadian mining industry, at present, there are no comprehensive regulations or guidelines that specify which approaches or methods are appropriate for use in the valuation of mineral projects. In January 1999, The Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission recommended that the Canadian Institute of Mining, Metallurgy and Petroleum establish a committee to review and advise on approaches and methodologies for the valuation of mineral properties. Among the approaches to be considered, are included the following: the Discounted Cash Flow Approach, the Cost Approach, the Option Pricing Approach and Market Comparables Approach. In addition, methodologies differ depending on whether the project is at the exploration stage or the producing stage.The CIMVal committee expects that its final report will form the basis for a standard Canadian Code for the valuation of mineral properties."

Jan 1, 2003

By Dong-Hyeun Koh, Yun-Soo Lee, Min-Seok Kim, Hyoung-Wook Kim

High strength AA7068 (Al - 7.88 wt.% Zn - 2.68 wt.% Mg - 2.07 wt.% Cu) aluminum alloy strip was successfully fabricated by horizontal-type twin roll casting. A simulation technique was used to obtain the range of casting conditions for fabricating strip without defects. The cast strip with thickness of about 5 mm was hot rolled, intermediate annealed, cold rolled to final thickness and subsequently annealed at various temperatures. Tensile properties of annealed and the aged specimens were evaluated at ambient temperature. Tensile strength and elongation of the annealed sheet are about 365 MPa and 28%, respectively. Also, the tensile and yield strength after the aging at paint baking condition (180 °C x 0.5 h) are 586 MPa and 551 MPa, respectively. Therefore, it is expected to show good formability prior to press or stamping and also provide high dent resistance after paint baking treatment.

Jan 1, 2015

By J. Jin, J. D. Miller

"Bubble attachment at hydrophobic surfaces is of critical importance in the flotation recovery of mineral resources and fundamental experimental results have been reported in the literature describing the details of film thinning, rupture, and displacement. Now, for the first time, bubble attachment phenomena are examined using Molecular Dynamics Simulations (MDS). The simulation involves a nitrogen bubble containing 906 nitrogen molecules in a water phase with 74,000 water molecules at the hydrophobic molybdenite (001) surface. During the simulation period of 1 ns, film rupture occurs and the nitrogen bubble attaches to the molybdenite (001) surface, resulting in a contact angle of about 90o. In contrast, the film is stable at the hydrophilic quartz (001) surface and the bubble does not attach. Contact angles, determined from MD simulation after stabilization of the three phase line of contact, are reported and these results agree well with experimental and MDS sessile drop results. In this way, film stability and bubble attachment are described with respect to interfacial water structure for surfaces of different polarity. For example, the interfacial water molecules for the hydrophobic molybdenite (001) surface have relatively weak interactions with the surface when compared to the hydrophilic quartz (001) surface, as revealed bythe presence of a 3 A water exclusion zone at the molybdenite/water interface. INTRODUCTIONAttachment of air bubbles to mineral particles is of fundamental importance in understanding flotation separation phenomena. It is well known that attachment of an air bubble at a hydrophobic surface includes film thinning, film rupture, and film displacement (Somasundaran, 2006; Wilson, Adlard, Cooke, & Poole, 2000). Experimental techniques, such as high speed video, can catch the process of bubble attachment at a mineral surface (Drelich & Miller, 2012; Niecikowska, Krasowska, Ralston, & Malysa, 2012). However, molecular scale information to examine the phenomena has not yet been reported."

Jan 1, 2016

By Gae On Kim, Ki Baik Kim, Suk Hoon Kang, Tae Kyu Kim, Sanghoon Noh

"Advanced radiation resistant oxide dispersion strengthened steel (ARROS) is being developed as a fuel cladding tube material for future nuclear reactor system applications. The research activities consist of advanced radiation resistant ODS steel development and fabrication technology development of ODS steel structural components. One candidate material with a chemical composition of (in wt%) Fe-10Cr-1Mo-0.5Mn-0.1V-0.25Ti-0.35Y2O3and was selected as representative materials, and this material was named as the advanced radiation resistant ODS steel (ARROSTM).On the basis of this ODS steel composition, an optimized fabrication process of structural components such as plates, sheets and tubes has been established through various process conditions in mechanical alloying, hot/cold working, and heat treatment processes. These R&D activities are expected to contribute to the realization of ODS materials in the future.INTRODUCTIONA sodium-cooled fast reactor (SFR) is being developed at the Korea Atomic Energy Research Institute (KAERI) with a view to economics, safety, reliability, and sustainability. The prototype Gen-IV SFR with a capacity of 150 MWe is under design, and this prototype reactor is scheduled to operate from 2028. For a commercial SFR system application, it is necessary to develop an advanced structural material having both high creep strength and irradiation resistance at high temperatures (Jeong, 2014). Oxide dispersion strengthened (ODS)steel is one of the most promising structural materials because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density, which is extremely stable at high temperatures under a neutron irradiation environment for a prolonged operating period(Kim, 2016). As the first step, several batches of ODS steel were designed and the candidate samples with a 2 kg scale each were fabricated by mechanical alloying, hot isostatic pressing and hot rolling processes. The mechanical properties of these samples were evaluated. Up to now, two candidate materials with chemical compositions of (in wt%) Fe-10Cr-1Mo-0.5Mn-0.1V-0.25Ti-0.35Y2O3 was selected as representative materials, and these materials were named as the advanced radiation resistant ODS steel (ARROSTM).The next step was to optimize the fabrication process of the ARROS compositions for in-core structural components such as the fuel cladding tubes of a SFR. An optimized fabrication process of fuel cladding tube with a composition of ARROS has been established through various process conditions in mechanical alloying, hot consolidation, hot/cold working and heat treatment processes. Joining technologies of the ODS steel tubes is being developed using solid-state welding such as magnetic pulse welding, friction stir welding and diffusion boding. It is expected that the development of ARROS will contribute to the realization of a commercial SFR with high economics and sufficient safety in the future. In this paper, the study of fabrication process of ARROS structural components is introduced."

Jan 1, 2017