Search Documents

By John G. Ayttes

"The following is a review of the advance of raise boring and its current position. The viewpoint presented is that the mining industry, through its worldwide acceptance of raise boring, has acknowledged the success of the method in general. Acceptance, however, does not imply complete satisfaction with either the equipment or current operating costs. Therefore, a brief review of how boring costs are being r educed is presented, citing examples. Recent raise borer applications of special interest are presented to show adaptability of current equipment, and some special projects in the planning stage are highlighted."

Jan 1, 1972

By E. Eccleston, E. Gardner, F. Letarte, R. Schonewille

"In 2005, after nearly a decade of process development and feasibility work, the commercialization of the Falconbridge Nickel Smelting Technology (NST) began in earnest with the design and construction of a grassroots ferronickel plant at Koniambo Nickel in New Caledonia. The NST process was developed as an alternative to the conventional Rotary Kiln-Electric Furnace (RKEF) process for production of ferronickel from saprolitic nickel laterite ores. The NST process promised environmental and energy efficiency advantages over the conventional route. A key step of the NST process involves fluidized bed pre-reduction of calcined laterite ore using direct injection of pulverized coal as the reductant. Two parallel fluidized bed reduction roasters (FBRs) were installed at Koniambo Nickel, each designed for a maximum capacity of 4,200 MTPD of calcined nickel laterite ore. This paper describes the process development and scale-up of the fluidized bed pre-reduction process, the design challenges associated with the prototype commercial units, and the current status of the FBR operation at Konaimbo.INTRODUCTION In the mid-1990s, Falconbridge began to develop a new flowsheet for production of ferronickel from nickel laterite ores. The process that developed came to be known as the Falconbridge Nickel Smelting Technology (NST). The flowsheet, which is particularly appropriate for saprolitic ores, involves several major unit operations, including: drying in a hammer mill-flash dryer, calcination and preheating in a flash calciner, pre-reduction in a fluidized bed reactor, and smelting in a DC arc furnace to produce the ferronickel product. This paper focuses on the fluidized bed pre-reduction step of the process and provides an overview of the process chemistry, laboratory and pilot plant development work, scale-up and commercialization of the pre-reduction step, and the results obtained in the prototype commercial units."

Jan 1, 2017

By A. Khan, C. Ciriello, W. Oliveira

"The purpose of this paper is to demonstrate the value of Operational Readiness (OR) in the successful delivery of capital projects. OR can be captured using several technical and practical definitions:• To ensure that the capital project being delivered is capable of an effective start up, ramp-up as planned and a sustainable productive operation.• To function as intended when started, with the appropriate people able to run it.• To increase the value in delivering the product/service through established systems, processes and procedures, while simultaneously minimize risk to both the project and the business.Historically, mining and metallurgical capital projects concentrate efforts on cost and scheduling during the implementation and design phases. The completion and subsequent handover of the operational unit is the main objective.When reviewing the mining and metallurgical industry’s capital projects, it seems many poor results and errors in terms of project design and ramp-up are self-inflicted, with the project neglecting to account for key aspects of the future operational plant. Interestingly, if the problems for the future plant occur during project implementation, they can be prevented during the project phase. It is required to connect the operational knowledge with the project in order to ensure an effective start up and operation.The benefits of OR will be shown to be applicable not only to mining capital projects but also to sustaining and business transformation projects. The paper also includes industrial examples showing both proper and improper use of OR techniques.The paper will cover 3 main areas of Operational Readiness: the OR model, OR related risk elements (i.e., risks associated specifically with the improper execution of OR) and conclude with OR specific case studies."

Jan 1, 2016

By C. Jay Hodgson, Adrienne C. L. Larocque

Abstract -The Mobrun VMS deposit in northwestern Quebec does not fit the classic Noranda­ type model, but exhibits characteristics more consistent with a Mattabi-type deposit. The orebodies are underlain by fragmental volcanic rocks indicative of explosive volcanism in shallow water. Felsic volcanic rocks are more abundant than mafic rocks. Alteration assemblages comprise chlorite, carbonate, sericite, and quartz. Broad semi-conformable alteration occurs high in the footwall to the 1100 lens. Mobrun occurs higher in the stratigraphic sequence than most of the other deposits in the Noranda camp. In this part of the stratigraphy, zones of pervasive carbonatization may be more useful guides for exploration than zones of silicification.

Jan 1, 1993

By H. Hejny

Economy needs mineral raw materials in almost each sector of modern life. They can only be provided by mining activities. An increasing share of the total mining production will be by underground mining. The mineral deposits will be found at gradually greater depths, including all problems associated with them. It involves an increase in overburden pressure with subsequent rock stability problems and risks of structural collapse. There is a need for new and safe technologies for almost all parts of a modern mine. The mining industry faces a number of challenges which require technical solutions that encompass the entire network and include the economic, social and environmental issues. The industry needs a new image based on pioneering solutions and a modern structure that can exploit minerals at greater depths and promote both high productivity and safe working conditions. Funding has been secured from the European Commission for the I²Mine project. Work started in November, 2011. This initiative is designed to focus on the technological challenges that the mining industry is currently facing including the exploitation of ever deeper deposits and the aspiration for an invisible, safe, zero impact mine. The project comprises a consortium of 27 organisations from 10 European countries. I²Mine marks the start of a series of development activities aimed at realising the concept of an invisible, zero impact, deep mine. The extractive sector, still seen as being old fashioned and environmentally unfriendly, will show that mineral extraction and processing can be done in a highly innovative and sustainable manner with low impact underground and zero impact above ground. The concept of I²Mine is to develop innovative methods, technologies, machines and equipment necessary for the efficient exploitation of minerals and disposal of waste, all of which will be carried out underground. This will dramatically reduce the volume of surface transportation of both minerals and waste, minimising above ground installations and reducing the environmental impact. New eco-efficient technologies will be applied in order to make the entire mining process more efficient and environmentally sound. The concept is for an integrated mine, with the majority of the installations underground, and only the final product will be transported above ground to be shipped to the customer. Production waste will be treated and stored underground and gaseous emissions will be managed underground as far as practical. I²Mine will also focus on ideas and concepts that increase energy efficiency and decrease waste. The core of the project will be to develop breakthrough technologies for autonomous, highly selective, continuous mineral extraction processes and machinery based on new sensor technologies, face front separation as well as innovative concepts for mass flow management and transportation integrating state of the art technologies. The concept of an invisible, zero impact mine requires a refined process underground that selectively extracts the mineral thereby reducing waste. For this reason, improved extraction machines and near to face processing methods, including backfill procedures, need to be developed. These developments include rock mechanics and ground control solutions, incorporating health, safety and environmental issues.

Aug 1, 2013

By Trang T. Tran-Valade

With continually increasing energy prices, the mining industry has been on the search for new energy optimization technologies. One area that is garnering great interest is Ventilation-On-Demand (VOD). Prior to selection and implementation of a VOD solution, it is important to fully understand the mine requirements as well as its existing infrastructure and the interaction with other automation in place at the site. With this information, a business case can be generated including a cost versus benefit comparison for various control strategies. To assist in the development of the business case, this paper will identify key areas for consideration and recommendations for an implementation plan.

May 1, 2013

By Laura A. Sanders

Mineral scale formation is prevalent in numerous mining operations. Such scale formation can occur in the direct-contact heat exchangers ahead of an autoclave. In these heat exchangers, the incoming slurry comes into contact with steam in a stage-wise fashion, which is re-circulated from the downstream flash vessels to heat the slurry in stages ahead of the autoclave. Calcium sulfate scaling causes severe problems in mining operations where increased temperatures are involved due to rising temperatures promoting calcium sulfate scaling through a decreasing solubility. In a number of these operations, the scale formation can occur in the presence of mineral solids, where fine-grained charged particles are at concentrations in excess of 35%. Scale prevention is not difficult in standard aqueous systems; however, the presence of solids leads to significant deficiencies in the prevention of scale due to the adsorption of the polymer onto the charge solids instead of the polymer interaction with the scale. Therefore, a technical solution to prevent mineral scale build up occurring in presence of pulp slurry in mining operations is needed. Several novel antiscalant technologies were developed and evaluated which provided a substantial improvement in the scale prevention in such systems.

May 1, 2013

By A. J. R. Smith

"CANADA'S ECONOMY TODAY is about two-fifths larger than it was six years ago, as measured by the total volume of production of goods and services. Such an achievement has been a rare phenomenon in Canada's first one hundred years. Excluding the forced-draft expansions which took place under war-time conditions, perhaps only the first decade of this century recorded a performance of greater dimensions, when, with massive immigration, the opening up of the West and a powerful array of well-de-signed development policies, the country was looking forward confidently to a great future of nation-building in the twentieth century.What makes Canada's over-all economic advance since 1961 all the more remarkable is that six years ago there was virtually no one in this country who anticipated an expansion of such dimensions. Back in the buoyant conditions of 1956-57, perhaps such an achievement would not have seemed beyond our grasp. After 1957, however, Canada stumbled through an extended period of slow economic growth, high unemployment and substantial and widespread under-utilization of its productive capacity. By the early 1960's, conditioned by the emergence of substantial, persistent and pervasive slack in the economy, t h e r e were few Canadians bold enough to anticipate that their economy was about to embark on a Great Expansion. However, this •is, in fact, what occurred. Beginning early in 1961, Canada moved forward into a sweeping advance which grew into the longest and largest peacetime business expansion in Canada's first century as a nation -a truly great expansion by any standard of measurement. This strong thrust has moved Canada into the front ranks of over-all economic expansion among the industrially advanced nations in the 1960's."

Jan 1, 1970

By Graham Walker

A new Code of Practice for the brake performance of off -highway vehicles was established in Alberta in 1976. Vehicles loaded to gross vehicle weight must be capable of stopping with mechanical brakes five times in quick succession on a grade of 10 per cent from a speed of 28 miles per hour. Comparative trials of various brake systems have been carried out and some combinations capable of meeting the Code are identified. Some problem areas in truck braking are reviewed and potential developments indicated.

Jan 1, 1977

By G. G. Richards, D. J. Rioux, R. L. Stephens

Teck Cominco Metals Ltd. operates an integrated zinc-lead complex at Trail, British Columbia, Canada. The year 2007 marks ten years of operation of KIVCETTM flash smelting technology for the treatment of zinc plant residues and lead concentrates. Since start-up in 1997, the furnace throughput has been increased to exceed its design rate and other metallurgical performance targets while continuing to meet its environmental objectives. This was achieved through resolution of key mechanical issues, improved understanding to stabilize the reaction shaft operation and control furnace accretions, significantly reduced boiler corrosion by molten chloride salts through the extensive application of weld overlay, a suite of projects to improve furnace integrity, and some debottlenecking of the surrounding unit operations in the lead smelter. The combination of increased feed rate and improved on-line time allowed the KIVCETTM furnace to set a new quarterly feed throughput record of 129,300 tonnes in the first quarter of 2008.

Jan 1, 2008

By C. V. Corless

1. Introductory Some members may recall that at the Annual Meeting two years ago I read a paper, 'The Future of the Mining Industry in Canada." Discussing this large subject it was possible only to outline the facts and inferences leading to ?the conclusion that Canada is a country endowed with enormous mineral wealth, of which the fringes are yet scarcely touched. In the present paper, I wish to examine in somewhat fuller detail the evidence, both direct and inferential, concerning the mineral wealth of the greatest physical and geological feature of Canada-the Precambrian Shield. Many, if not most, of these facts are already familiar to you. But, since they will form the basis of the reasoning employed, they will be recalled for explicit reference. First, let us review very briefly the position and extent of the Shield. The area of the entire Shield is given in textbooks as 2,000,000 square miles, of which perhaps 10 or 12 per cent. is exposed in the south-easterly part of Canada's Arctic islands. The remainder occupies roughly two-thirds of the North-west Territory; the north-east corner of Alberta; one-third of Saskatchewan ;two-thirds of Manitoba; three-fourths of Ontario; and nearly ninety-five per cent. of Quebec.

Jan 1, 1924

By Marcin Ziemski

This paper reports on an energy efficiency analysis completed as part of a research project looking at energy reduction opportunities in minerals processing operations. The plant discussed is a gold production facility owned by Newmont Gold in the Tanami region of central Australia. Due to its remote location, lack of nearby gas pipeline or power grid, the operation has been completely dependent on diesel fuel for its electricity generation and transport needs. The mine and processing plant use electrical power at a rate of 12MW to 18MW, resulting in a monthly electricity cost of over US$1.5M. The high cost of diesel combined with an impending power generation capacity shortage drove Newmont to undertake the energy efficiency study. An energy audit of the plant showed opportunities for significant energy savings through the strategic use of waste heat, fuel replacement alternatives and renewable energy sources.

May 1, 2007

By Lewis Finch

Oil and .gas reservoirs exist under pressure within the pore spaces of rock structures or traps. Wells are drilled to produce these reservoirs. Under primary operation, the natural energy of expanding fluids in and adjacent to the reservoir forces or drives oil and gas to the wells. There are three basic sources of energy: dissolved gas, water, and gas cap. Typical recovery by primary methods is only 10 to 25 per cent of the oil in place for the dissolved gas drive but is generally higher for the others. Secondary recovery involves the injection of water or gas to supplement natural energy, thereby increasing recovery over that obtainable by primary operation alone. In many cases ultimate recovery with secondary methods is 1.2 to 2.0 times the expected primary recovery. The type programme adaptable in a field depends on its 'primary performance and on certain reservoir characteristics. In the United States, application of secondary recovery methods is becoming increasingly important. About 22 per cent of United States oil production now comes from fields in which injection projects are operating. In 1953, nearly 1.4 million barrels of oil daily came from such fields, more than double the amount in the early 40's. Ultimate primary recovery from known pools is estimated at roughly 73 billion barrels. Secondary recovery projects already in operation will increase this to almost 80 billion, an increase of almost 10 per cent. Unitized secondary recovery projects have been very successful. From unitized projects alone, industry reserves of oil in the United States have been increased by 3 1/2 billion barrels. In Canada, secondary recovery has not been so wide spread mainly because D-3 reef reservoirs which have held the major reserves are under water drive. However, appreciable amounts of water are being injected in the Redwater D-3, Leduc D-2 and Joarcum Viking reservoirs, and gas in the Golden Spike D-3. In both countries, possible achievements in increased recovery through secondary recovery methods now in use and by new ones which may be developed through research and field trial are a challenge to the scientist and the industry.

Jan 1, 1956

By M. L. Smith

"In the Phosporia formation of SE Idaho, ore quality varies by depth, seam and distance along strike; phosphorus recovery is sensitive to these variations. Plant ore feed can be blended over time to minimize this fluctuation by using a combination of mine production and inventory stockpile scheduling. Mixed-integer and goal programming has been used to optimize short-term mine production, but the seasonal nature of mine haulage requires the use of stockpiles both at the mill and the mine. The contents of the stockpiles can also be optimized as part of the production scheduling problem, but introducing inventory control introduces a nonlinear term into the formulation. A solution using a piecewise linear formulation is modelled and solved using AMPL/Cplex, and solution strategies are discussed for similar large-scale problems. IntroductionIdaho’s minable deposits of phosphate rock are found in the Meade Peak member of the Phosphoria Formation; two separate zones of this formation are mined with a combined thickness of 30 ft to 60 ft. A generalized stratigraphic section of the Phosphoria section is shown in Figure 1, illustrating the degree of complexity encountered when scheduling mine production. Alteration of the formation results in higher grade ore zones near the surface and variable in P2O5 levels between seams and along strike. This variability is seen as well in other quality characteristics critical to the production of acid and elemental phosphorus. Further, plant recovery and nodule quality are sensitive to variations in ore feed; variability in SiO2, carbonates, moisture, organics (carbon), P2O5 and other constituents of the ore can strongly affect plant recovery. Because ore quality characteristics can vary as a function of the alteration zone (or seam) being mined as well as the depth and distance along the strike of the formation, scheduling of mine production can have a highly significant effect on recovery in the plant. As illustrated in Figure 1, there are nine seams containing 20% to 35% P2O5. Phosphoric acid and elemental phosphorus production requires an ore content of 30% and 25% P2O5, respectively. Variability between numerous beds that are mined and quality variation within a seam due to alteration greatly complicates production scheduling with the result that erratic mill feed characteristics greatly decrease recovery."

Jan 1, 1999

By E. Asselin, G. K. Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe(II)Fe( III)H2SO4 solution at 90 °C and 110 °C. Results from the calculation of speciation in the above solution reveal that, at both 90 °C and 110 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller VALUES (for the reversible potential of the ferric/ferrous couple. Exchange current densities of the ferric/ferrous couple were obtained and are on the order of 106 10 5 A/cm2 a t 9 0 °C and 1 07 10 6 A/cm2 at 110 °C, respectively. The Tafel slopes from the CPP method are higher than those from the CPC method at both 90 °C and 110 °C. The transfer coefficients were about 0.360.59 at 90 °C and 0.370.65 at 110 °C. Based on the exchange current densities obtained, the rate constant kc was calculated. It was found that kc at 90 °C was slightly larger than at 110 °C, especially for the results obtained by the CPC method. The average rate constants are 862.17 cm/s for CPC and 65.30 cm/s for CPP at 90 °C, and 477.69 cm/s for CPC and 63.53 cm/s for CPP at 110 °C for nominal Fe3+/Fe2+ ratios ranging from 1:1 to 1000:1. INTRODUCTIONChalcopyrite is one of the most abundant copper-bearing minerals, accounting for approximately 70% of the world’s known copper reserves (Wang, 2005). Most of the currently proposed leaching processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale, such as Activox (U.S. 5,232,491, 1993), Nenatech (U.S. 5,993,635, 1999), Dynatec (U.S. 5,730,776, 1998), AAC/UBC (U.S. 6,503,293, 2003), Total Pressure Oxidation (U.S. 5,698,170, 1997), CESL (U.S. 5,874,055, 1999) and Galvanox (U.S. 7,846,233, 2010).To date, much effort has been devoted to understanding the kinetics and mechanisms of the oxidative processes (Biegler & Horne, 1985; Córdoba, Muñoz, Blázquez, González, & Ballester, 2008, 2009; Ghahremaninezhad, Asselin, & Dixon, 2010; Hirato, Majima, & Awakura, 1987; Hiroyoshi, Kuroiwa, Miki, Tsunekawa, & Hirajima, 2004; Warren, Wadsworth, & El-raghy, 1982) or the cathode reduction reactions of chalcopyrite itself (Arce & González, 2002; Biegler & Swift, 1976; Biegler, 1977; Nava, González, Leinen, & Ramos-Barrado, 2008), by chemical or electrochemical methods. However, as the most important cathodic processes in chalcopyrite leaching systems, the cathodic reductions of ferric ions or dissolved oxygen are worth measuring due to their effects on the overall leaching rate, as predicted by mixed potential theory."

Jan 1, 2012

By W. G. Jeffery

"The mining and mineral industries have been, and remain, a major component of the Canadian economy. There are approximately 560 producing mining establishments of which there are some 130 metal mines and an equal number of non-metal mines, the balance being quarries for stone, sand and gravel. For 17 metals and minerals, Canada ranks within the top five as a world producer. There are 29 metallurgical plants. Employment in mining, smelting and refining was about 150000 in 1990. Mineral production, including coal, is about $20 billion. Exports up to the metal stage amount to $15 billion providing a positive trade balance of some $10 billion.The producing industry has a wide diversity of products. The companies range from small single mining operations to large multinationals. In terms of technology the industry has always been in the forefront of cost-effective practice, either using home-grown innovation or freely importing technology from around the world,The Mining Industry Technology Council (MITEC) makes an annual survey of the exploration and R&D expenditures of the senior mining industry that is the mining companies that are involved in mineral production from their existing mines. It does not include those companies solely involved in exploration using funds raised through equity sales.Table 1 shows the actual R&D and exploration expenditures as a per cent of sales. R&D shows a rising trend since 1988although the drop in value of output due to lower prices must be recognized as contributing to the increase. The point about this compilation is that the mining industry re-invests some 4070 of its sales in both exploration and R&D in order to sustain itself. Exploration for the renewal of metal inventories for future mining is a process unique to mining. It is not classified as R&D, and the necessity for this investment goes unrecognized by those who state that the industry does not do enough R&D."

Jan 1, 1993

By J. Bakos

Solar Hydrogen Energy Corporation (SHEC Labs) recently constructed a pilot-plant to demonstrate a Dry Fuel Hydrogen Generation System that is powered primarily by sunlight focusing-mirrors. The pilot-plant consists of: A Solar Mirror Array and Advanced Solar Concentrator and Shutter System; and two thermo-catalytic reactors to convert Methane, Carbon Dioxide, and Water into Hydrogen. Results from the pilot study show that Solar Hydrogen generation is feasible and cost-competitive with traditional Hydrogen production. More than 95% of Hydrogen commercially produced today is by the Steam Methane Reformation (SMR) of natural gas, a process that liberates Carbon Dioxide to the atmosphere. The SMR process provides a net energy loss of 30 to 35% when converting from Methane to Hydrogen. Solar Hydrogen production provides a 14% net energy gain when converting Methane into Hydrogen since the energy used to drive the process is from the sun. The environmental benefits of generating Hydrogen using renewable energy include significant greenhouse gas and criteria air contaminant reductions.

Jan 1, 2005

By Donald J. MacNeil

THE opinion, based upon geological knowledge, that certain areas within the Province of Nova Scotia might yield commercial quantities of petroleum, is not new. It dates back to at least 1864, when the Pioneer Oil and Salt Company drilled some shallow holes in search of oil near lake Ainslie, Cape Breton. As a matter of fact, several companies were engaged in oil exploratory work near lake Ainslie at about that time; included among them were the Inverness Oil and Mining Company, the Victoria Oil Company, the American Oil Company, and the Cape Breton Oil and Mining Company. Oil exploration by these and other companies was conducted sporadically on Cape Breton island until 1914. In several instances, the depth of the test holes exceeded 1,000 feet; the deepest was carried to 3,260 feet. The Lake Ainslie area was selected because oil seepages were present along certain sections of the lake shore, but the tests that were drilled to tap the oil-bearing zone failed to yield anything of commercial value. Currently, there are three areas in Nova Scotia wherein active exploratory work is being conducted, namely, at Pugsley Siding close to Amherst; at Kennetcook, Hants county; and near Mabou, Inverness county. The Pugsley Siding test is being drilled by the Sun Oil Company, of Philadelphia; the work at Kennetcook is under the direction of the Nova Scotia Oil and Gas Company; two relatively deep holes were drilled by the Lion Oil Refining Company in 1944 near Mabou, and, as a result of the additional geological information derived therefrom, another test probably will be drilled by this Company in the same area. Aside from these activities in the search for petroleum, the oil possibilities of several other sections of the Province are being studied by means of surface geological mapping.

Jan 1, 1945

By Cindy Schiewek

Industrial injury occurrences are an ongoing concern for Mine Operators. Along with the personal suffering of injured workers comes an increase in compensation and productivity costs. Growing recognition of repetitive stress and bodily injuries, accompanied by recent studies, validates the assumption that a relationship exists between ergonomic injuries and machine design. Intuitively, there is a belief that an ergonomically designed machine will reduce repetitive stress injuries through design and education however; quantifying this belief has been a challenge for Mine Operators. Sandvik Tamrock has undertaken a project aimed at developing a business model to assist in quantifying the benefits of ergonomic intervention. This model focuses on distinguishing and quantifying this method of intervention to allow for a better evaluation of the machine. For simplicity, the project initially focused on the Face Drill Jumbos. The target of the project was three fold: !" Recognition of the cost drivers for compensation; ergonomic injuries !" Identification of the relationship between ergonomic machine design, and the decrease of the negative effects associated with the cost drivers !" Systematic prioritization for ?prevention by design? The project findings substantiate the expected reduction in injuries and compensation claims. Based on all ergonomic intervention studies conducted, each case showed a reduction in compensation cost; through prevention by design, one can reduce the amount of potential risk. The paper addresses the resources and methodology used, along with the findings and its relevance to the issues that face the Mining industry.

May 1, 2003

By Robert A. Macinnes, Peter Moon, John P. Pappone

"This paper, in presenting the results of the application of the assessment centre method at Texasgulf Canada Ltd., illustrates a novel "" in-use"" technique for manpower training in the mining industry.IntroductionMining history is full of examples of what goes wrong when human judgment fails-disasters, floodings, loss of life and property. We must, therefore, assume the importance of selecting competent people for supervisory responsibility. This article de scribes a method for assessing supervisory ability, its first application in Canadian mining and the result s obtained over the past six years. It is known as the assessment centre method."

Jan 1, 1981