Search Documents

By Steve Piercey

Introduction ? VMS Deposits: The Target ? Key points for every belt: heat flow and extension. ? Good felsic rocks ? Good mafic rocks. ? Petrochemical assemblages. ? Summary Key Points Throughout ? Common themes: ? Heat ? driver of the hydrothermal system ? Extensional geodynamic setting ? conduits to focus fluid flux ? (e.g., Lesher et al., 1986; Swinden et al., 1991; Barrie et al., 1993; Lentz, 1998; Syme et al., 1999; Piercey et al., 2001, etc.) ? We must identify rocks, belts and tectonic environments that encompass these two criteria (among others but?) ? e.g., forearc rifts, intracontinental rifts, arc rifts, and back-arc basins.

Apr 1, 2005

Safety Leadership The management and leadership of a mining operation is a challenge at all times. The pressure to make production, safety, and environmental goals is intense. At some point mining cycles will put every operator into periods of time where economic issues seem to over-ride all other concerns. This is when leadership is most needed.

May 1, 2009

By Adam J. Szladow

"INTRODUCTIONThe low calorific value and the high moisture and ash contents of run-of-mine (r.o.rn.) lignite limits the utilization of Saskatchewan lignites to thermal power plants in Saskatchewan, Manitoba and western Ontario. On the other hand, the low sulphur content and the low mining cost make lignites potentially attractive for new coal markets, if suitable processes can be found for upgrading. Economic upgrading to a higher quality fuel would make lignites more acceptable for industrial and utility boilers.This paper presents a summary of the process engineering evaluation of coal upgrading technologies conducted in support of a study of selected lignite upgrading processes. The summary presents the relative advantages and offers specific comments on the application of coal upgrading technologies for lignites. ResourcesLignite comprises the largest fossil fuel energy deposits in Saskatchewan. The total resources of immediate and future interest exceed 27 billion tonnes. The measured and indicated lignite resources of immediate interest are large enough to last for over 200 years at the current production rate of about 10 million tonnes per year (Table 1).Saskatchewan lignitedeposits are present in three different geologic formations: (I) the Ravenscrag Formation of Paleocene Age in southern Saskatchewan; (2) the Swan River Formation of Lower Cretaceous Age in central north Saskatchewan; and (3) the Judith River Formation of Upper Cretaceous Age in central west Saskatchewan. The deposits in the Swan River and Judith River Formation are not currently of economic interest.The Ravenscrag deposits are confmed to four lignite basins, namely: the Estevan, the Willow Bunch, the Wood Mountain and the Cypress basin (Fig. 1). The estimated resources of immediate interest in the four basins are over 7 billion tonnes (Table I). These resources include lignite seams at least 1.5 m thick, at depths of less than 45 m.The average quality of lignite varies relatively little between the four basins considering the distance between deposits (Table 2). There is, however, a progressive increase in moisture and ash content, and a decrease in calorific value and carbon content as one moves westward from the Estevan to Wood Mountain and Cypress basins. The Estevan area deposits are of higher rank despite the fact that they are stratigraphically younger than the Willow Bunch deposits (Cameron and Marconi, 1979).In upgrading lignite to a higher quality fuel, it is important to know not only the average proximate and ultimate analysis (Table 2) but also other lignite characteristics influencing the product quality . For example, Figure 2 shows the effect of lignite HIC ratio on the product equilibrium moisture for hydrothermal treatment of lignite. It is apparent that lignites with a higher HIC ratio, or high liptinite content yield much better quality product for the same hydrotreatment conditions. Other examples of lignite characteristics which are important in upgrading include distribution of sulphur forms and mineral matter, maceral composition and degree of surface oxidation."

Jan 1, 1989

By Hung-wei Liu, Kevin Plucknett

Early attempts to manufacture titanium aluminides using blended elemental powders, through powder metallurgical processes, have been obstructed due to serious swelling during sintering. Although the use of pre-alloyed powder can avoid this undesired expansion problem, there are limited commercial powder sources available. Therefore, in the present research, fundamental studies on the synthesis of dual-phase (? plus a2) Ti48Al intermetallic materials is undertaken, in particular assessing powder manufacture. In order to produce pre-alloyed powders, highly porous Ti48Al pieces are initially sintered from elemental Ti and Al powder blends, and subsequently pulverised into powders. The powder size is then further reduced by use of either dry or wet milling processes (i.e. shatterbox grinding, attrition, or ball milling). Among these methods, shatterbox grinding has shown the highest efficiency, with a slight mechanical alloying effect observed. The manufactured powder morphologies and phases, as well the sintered material, will be discussed.

Jan 1, 2015

By Qiling Zhang, Zengqian Hou, Xiaoming Qu

Abstract - The Okinawa trough is an active back-arc-spreading center in which submarine hydrothermal exhalation (black chimneys) and sulfide mineralization are forming. Fluid inclusion composition in minerals of the hydrothermal feeder zones in the JADE field shows that the hydrothermal systems are extremely gas-rich. There are two independent and co-existing fluids, CO2-hydrocarbon and saline fluids. Microthermometry and Laser Raman Microprobe (LRM) analyses on individual fluid inclusions of the CO2-hydrocarbon type, dominated by CO2 and containing minor CH4, C2H4, C2H6, N2 and H2S, are almost equivalent to the fluid inclusion composition of a natural gas field. The saline fluid is mainly composed of H2O and contains minor Na+ and K+. It is close to a H2O-NaCl, or H2O-NaCl-KCl system, with salinities from 3.7% to 7.5% NaCl eq. Before venting on the seafloor, the fluids experienced immiscible separation. One of the end-member fluids is downward circulating seawater that interacted with sub-seafloor rocks. The other was gas (volatile)-rich fluid derived from a shallow magma chamber. The immiscibility separation of fluids resulted from the decrease of temperature and pressure of the hydrothermal system and continuous input of magmatic volatiles. The saline fluids in this system are discharging to form sulfide chimneys and black smoke. Meanwhile, CO2-rich fluid discharges as CO2 bubbles through hydrate pipes. A large amount of CO2-CH4-H2S gas or fluid in the upper part of the hydrothermal system, and reaction of this gas or fluid with saline fluids, finally enables the accumulation of metal sulfides.

Jan 1, 1999

By D. Beneteau

Plotting sets of data collected over time using a frequency-magnitude distribution is common with both earthquake and mining seismology. A Time-Between-Events (TBE) analysis technique simply makes use of the inter-event times and b-values (slopes of the best fit lines on the frequency-magnitude charts) from the same set of data. Four distinct patterns in TBE versus Event Magnitude have been found which suggest whether there are constant seismic sources causing populations of data, or if the smaller and larger events, within the population represent varying seismic sources. Different rates of events, identified as TBE-rates in this study, may suggest whether the events are blast induced, or not. This study was done using actual seismic datasets from hardrock mines in Canada and Australia. This was to verify the applicability of the method to multiple mining environments and to determine the practicality and implications of this methodology to enhance the interpretation of seismic source mechanisms The results of the TBE technique and other proven techniques are combined into a Seismic Mechanism Assessment Worksheet. This is a tool that allows operators to compare trends within seismic datasets with assessments of in-situ rock conditions. The goal is to enhance the understanding of rockmass failure mechanisms.

Nov 1, 2011

By Jacques Ouellet

Outline What is Microwave energy Investigation of transparency of 40 minerals Melting of Andesite in a MW oven Numerical modeling /Computer Simulations o FEM analysis ?? Some laboratory experiments o Particle Modelling Mw Application to Rock Breakage o A MW Rock Drill Prototype Conclusions What is Microwave energy Microwave energy is an electromagnetic wave consisting two electronic & magnetic wave traveling perpendicular to each other and transporting energy with the speed of light.

May 1, 2008

By M. Pearson, W. Bristowe, A. Hanson

"There's no such thing as quality assurance; only quality control ... by inspection. "(1) A common misunderstanding in the procurement and construction of custom designed, fabricated pressure vessels and piping systems is that quality assurance can be achieved by simply referencing codes, standards, ISO 9002, QMS or other such programs in the contract documents. In the authors' experience, nothing could be further from the truth, not detrimental to the performance of the equipment than the exclusion of inspection activities and reliance upon warranties and "fit-for-purpose" clauses. Likewise, the expectation that fabricators, suppliers, or third party inspectors can provide such assurances is also unrealistic where they have limited knowledge of the process, material selection criteria, or limited technical resources. The development and successful execution of a quality assurance program is a collaborative effort by engineers, designers, material suppliers, equipment fabricators, and field inspectors with the full understanding and support of the end user.This paper presents an outline of the quality control activities undertaken by the authors for several recently completed and on-going hydrometallurgical projects. The activities include: prequalification of fabricators and sub-vendors, shop audits, material validation testing, material source control and verification, positive material identification of weld metal overlay, specialised welding inspection, contamination control for titanium and titanium-clad fabrication, eddy current and mass spectrometer (helium) leak testing of shell-and-tube heat exchangers, hot cycle testing of titanium clad equipment, tolerance verification for refractory lined equipment, final inspection and cleaning.

Jan 1, 2004

By A. R. Trusiak, C. Bazin, D. Hodouin

"The On-Stream Analyzer has proven, and is still proving to be, an extremely valuable tool for the control of flotation circuits. This paper examines the possibility of going further in the utilization of the analyzer results by using a real-time material balance program to calculate the mass flow rates within the streams of a circuit for process control, analysis and optimization as well as for the detection of sensor malfunction. The material balance algorithm improves measurements and give good estimates of unmeasured variables during normal operating conditions. The potential and limitations of the method are illustrated using results of an application to the Line 3 flotation circuit of Brunswick Mining and Smelting, New Brunswick.IntroductionThe On-Stream Analyzer (OSA) has gained, over the last two decades, the status of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant and its application in oxide mineral flotation plants isincreasing. Commercial OSAs include a sampling system that collectssamples from various streams of a circuit and exposes thesamples to an X-ray beam. The sample then generates X-ray pulsesthat are converted into assays using multilinear regression programs(Leroux and Franklin, 1994). The estimated assays arepassed to the flotation operators via operator consoles, or to controlloops of various degrees of complexity (McKee, 1991), whichmanipulate reagent addition, aeration rate or froth thickness toensure an adequate operation of the plant. Although this applicationrapidly pays for the purchase of the OSA, one should ask:""Could we get more from the OSA?"""

Jan 1, 1995

By Arnold R. Pasieka, George V. Sotirow

"The object of this paper is to outline a computerized net cash flow approach for practical cutoff grade determinations. A cutoff grade carries not only geological but also economic value, in which costs are balanced against revenues. For different situations, cutoff grades are a 'standard of value' that are determined for the purpose of classifying economic or uneconomic mineral reserves in a specified time frame. In a constantly changing technical and economic environment, the decision to develop or maintain a mining operation at its best economic potential, requires an appropriate cutoff grade strategy, a strategy consistent with short- and long-term operational and corporate objectives and one based on realistic marketing and metal prices forecasts. The use of a project evaluation computer program, in combination with specific corporate net cash flow requirements, shows the most promising and flexible team approach for cutoff grade optimization.IntroductionThe recent recession has had a devastating effect on the Canadian mining industry. Exploration and mining R&D expenditures have been critically reduced and now are believed to be below healthy levels. Ore reserves, mine life and cutoff grades are careening in several directions because of low base metal prices, relatively high costs and sensitive precious metal prices.These conditions demand an improved understanding of the terms ""ore"" and ""cutoff grades"" as they are applied to the planning process and day-to-day operations. ""Ore"" or 'ore reserves"" is a dynamic concept, reflecting a cumulative effect of changes in geological, technical and economic conditions in terms of material which can be mined at a potential profit. By contrast, if economics are not the primary consideration, the term ""mineral reserve"" or ""mineral inventory"" should be used to describe the mineral deposit. For different situations, cutoff grade is ""a standard of value"" determined for the purpose of classifying mineral reserves as economic or uneconomic in a specified time frame. The question of mining at average reserve grade or low-grade material during high metal prices is of paramount importance for cutoff grade strategy."

Jan 1, 1985

By R. L. Eadie, J. L. Luo

The effect of plastic deformation on near-neutral pH stress corrosion cracking (SCC) also known as environmentally assisted cracking was studied by cracking rate measurements. All the tests were conducted in a synthetic near-neutral pH solution. The traditional potential drop tests using compact toughness (C-T) specimens with 2-3 mm long pre-cracks showed varying plastic deformation by rolling would increase the material's susceptibility to SCC. This was confirmed by cyclic loading tests using double notched flat tensile specimens with 200-300 µm long pre-cracks which gave the same results that the specimen with large scale plastic deformation by tensile loading had a relatively faster crack growth rate than that with only small scale plastic deformation.

Jan 1, 2005

By Ainul Akhtar, Steve Cockcroft, Daan Maijer, Carl Reilly, Lu Yao, Jun Ou

A coupled thermal-fluid flow-multicomponent model has been developed to aid in understanding the melting/dissolution behavior of solid Al-rich Material (TiAl) in a liquid titanium pool produced by an electron beam. The model is capable of accounting for the significant phenomena present affecting heat, mass and momentum transport including thermal and compositional buoyancy and Marangoni forces, Darcy attenuation, evaporation, melting and solidification, and the associated release or absorption of latent heat. The modeling results have indicated the compositional fluid flow driving forces (compositional buoyancy and Marangoni forces) contribute significantly to the melting/dissolution process. The model is waiting for validation against empirical data.

Jan 1, 2014

By H. Lee

Recently, the effects of global climate changes have become top concerns for governments? decision making regarding infrastructure investments. Extreme weather events that exceed the capacity of existing systems have considerably increased in frequency, and the potential effects of changing trends in temperature and rainfall on infrastructure are difficult to ignore. It is essential for governments to estimate the costs and benefits of adaptation to climate change to properly assess the financial feasibility of infrastructure adaptation strategies. This paper proposes a framework for estimating the economic aspects of infrastructure adaptation to climate change. The framework is composed of three steps of implementation: establishment of alternatives for infrastructure adaptation, performance prediction of infrastructure using future climate scenarios, and asset valuation based on costs and benefits. The first step specifies target assets, their adaptability to climate change, and applicable adaptation technologies. The second step evaluates the effects of climate change on the performance of infrastructure. The last step determines the optimal adaptation strategies among various alternatives based on their net benefits. The framework reasonably incorporates future climate scenarios into the estimation processes for climate change effects and provides a basis for budget allocation for governmental infrastructure investments. The framework is expected to assist government decision makers in establishing adaptation strategies in a rational manner under uncertain future climate change.

Aug 1, 2013

By J. Donovan

Underhand cut and fill mining is being planned for selected areas at the David Bell Mine where high ground stresses have resulted in particularly challenging mining conditions. In order to test the placement and performance of a variety of underhand cut and fill paste mats three different designs have been installed and extensively instrumented along the A-Zone 9C ore sill. The sill is approximately 87m long, 4.0m high, and 5.0m average width. The sill was broken into 3 sections each of which will contain one of the sill mat designs. The underhand sill will be mined 3.75mW x 4.0mH, allowing for some overbreak while minimizing the risk of the back span exceeding the design limit of 4.0mW. Each test sill mat includes pre and post-support and includes 0.5m (18?) broken muck mat placed along the sill floor. Upon developing beneath these mats quantitative and qualitative measures will be used to determine which design is the most suitable for application in underhand mining at David Bell.

May 1, 2007

By M. Pelser, H. Gous, J. H. W. M. Brits, K. Voogt

The effect of impurities; iron and selenium, on current efficiency and deposit quality in copper electrowinning was investigated using an at-line cell at the Rustenburg Base Metals Refiners’ Copper Tankhouse. The tankhouse is a direct leach, starter sheet electrowinning operation with a unique electrolyte composition. The effect of iron on the current efficiency in the at-line cell was found to be less severe than reported in literature. However, the distinction between the chemical impact of iron on current efficiency and the physical impact of iron on a starter sheet operation needs to be realised. The effect of selenium on current efficiency and deposit quality is also reported. INTRODUCTION Anglo American Platinum’s Rustenburg Base Metals Refiners’ (RBMR) Copper Tankhouse serves a unique function in the refinery flowsheet in that its primary functions are the removal of copper and production of acid for the leach circuit. This function needs to be performed to specification in order to keep the leach circuit operating optimally. Current efficiency is seen as an indicator of tankhouse performance and efficient energy use. The tankhouse plates starter sheets onto titanium blanks which, after stripping and preparation, return into the production cells for further plating. Approximately 78% of tankhouses surveyed (Robinson et al., 2013) use permanent cathode technology whereas older, smaller operations still use starter sheet technology. Drawbacks of the starter sheet technology are that the starters are thin and bend easily leading to increased shorts, they need to be removed after two days of plating to be manually straightened and are then returned to the cells. In addition, the electrolyte levels in the cells need to be adjusted during the plating cycle to improve loop adhesion to the cathode and reduce loop corrosion. The starter sheet technology is therefore very labour intensive and the final quality of the product is dependent on the quality of the starter sheets produced. In comparison, permanent cathode or direct plating technology lends itself to automation, allows for higher current densities and better cathode quality due to more robust geometric stability in the cell. The present barrier to implementation of permanent cathode plating at the RBMR Copper Tankhouse is the capital cost required to convert the tankhouse, i.e. blanks and stripping machine. At present, alternatives to titanium blanks, such as LDX 2101, are being investigated for the unique electrolyte composition of this tankhouse.

Jan 1, 2019

By J. B. Sabey, V. R. Degner, D. MacGillivray

"Hydrodynamics principals are applied to the design of a natural air ingestion flotation machine for coarse solids applications. Preliminary laboratory test data and subsequent operating plant flotation kinetic performance evaluations are reviewed. INTRODUCTIONThe concentration of potash (sylvite, KCI) from halite and other salts using flotation is well understood and practice a with much success. Reagent schemes and plant circuitry for obtaining the desired product recovery and grade have been established with proven performance. These flotation circuits normally process the medium and finer size particles, less than 30 mesh (600 microns).However, often the potash market trends specifically demand a coarse product size. This emphasis, accompanied by the existing high losses of coarse (+30 mesh) potash in flotation circuits, creates the need for development of a flotation machines specifically designed for coarse potash beneficiation.This technical challenge was undertaken by the WEMCO Research and Development Group. The specific objectives of this flotation machine development program were ( l) to achieve an ""Ultra Coarse Flotation Machine"" capable of adequately suspending and transporting particles in the 4 - 30 mesh (4.75 - 0.6 mm) size range at solids concentrations of 30% or greater and (2) ascertain metallurgical performance of this machine.This paper covers the development (both theoretical and mechanical/ hydrodynamic), the field test program and results, a discussion of applicable flotation kinetics, and conclusions of this ""Coarse Potash Flotation Machine"" development project."

Jan 1, 1986

By Ray Mason

Marathon PGM Corporation?s PGM-Cu Project in Northwestern Ontario (Figure 1.0) serves as a case study to describe the process involved in advancing a deposit from grass roots exploration to the completion of several feasibility studies and the parallel commencement of environmental permitting. Through the following examination of historical exploration activities, it is clear that these activities are directly related to economic stimulus, mostly measured by downturns in the mineral industry. Other factors that influence the success of exploration advancing to feasibility and new mine development includes the ownership of the mineral claims, which also changes under these economic influences and the crucial role of interactions between the Company, the Crown and First Nations. The Marathon PGM-Cu deposit is hosted within the Eastern Gabbro Series of the Proterozoic Coldwell Complex, which intrudes and bisects the much older Archean Schreiber-Hemlo Greenstone Belt. The sub-circular complex has a diameter of 25 km and a surface area of 580 km2 and is the largest alkaline intrusive complex in North America (Walker et al., 1993). Mineralization at the Marathon PGM-Cu deposit is part of a very large magmatic system that consists of at least three cross-cutting intrusive olivine gabbro units that comprise the Eastern Gabbro Series of the Coldwell Complex (Figure 3.2.4-3). In order of intrusion, the three gabbroic units consist of (1) Layered Gabbro Series, (2) Layered Magnetite Olivine Cumulate (LMOC) and (3) Two Duck Lake (TDL) Gabbro. The relative size and abundance of the gabbroic units decrease in the order Layered Gabbro Series>TDL Gabbro>>LMOC. Late quartz syenite and augite syenite dikes cut all of the gabbros but form a minor component of the intrusive assemblage.

May 1, 2010

By K. D. Card, K. Howard Poulsen

Abstract - The Archean Superior Province craton and the Paleoproterozoic Penokean Orogen are major geological sub-divisions of the southern Canadian Shield and account for much of the metallic mineral production of North America. The Superior Province experienced a mainly Archean history involving several cycles of volcanism, plutonism, and tectonism, primarily in the Neo-archean but also including Meso-archean and Paleo-archean cycles as well. Superior Province consists of northern and southern high-grade gneiss sub-provinces and a broad central region of alternating greenstone-granite and metasedimentary belts. The sub-provinces may represent tectonic terranes assembled in the Archean by accretion processes similar to those of some Phanerozoic orogens. Most of the mineral deposits, including VMS, intrusion-related, and lode gold deposits occur in the greenstone- granite sub-provinces where they were formed in an interval of 100 million years or less around 2.7 Ga. The Paleoproterozoic Penokean Orogen comprises supracrustal sequences deposited in fault-controlled epicratonic and rifted margin settings developed on and about the Superior craton. Deposition of the ~2.4 Ga Huronian Supergroup and its paleoplacer uranium deposits in the eastern Penokean Orogen, and their pre-2.2 Ga deformation, were probably unrelated to the deposition of the ~2.1 Ga Marquette Range and Animikie groups and their major taconite iron formations in the west. However, these sequences were deformed together during the ~1.85 Ga Penokean Orogeny which resulted when an assembly of island arcs containing VMS deposits, the Wisconsin magmatic terrane, collided with the Superior block and its Paleoproterozoic cover. The Sudbury structure with its world class Ni-Cu-PGE ores was also formed at this time, possibly triggered by meteorite impact. Metallogenic patterns in the Paleoproterozoic rocks were controlled by a complex interplay of factors including tectonically controlled variations in deposition and deformation, distribution of mineralization in the Archean basement, and oxyatmoversion, the transition from anoxic to oxygenic atmospheric conditions that occurred during the deposition of these sequences.

Jan 1, 1998

By Tatsuya Oki

Tantalum capacitors can be found mounted on printed circuit boards of domestic appliances such as personal computers. These capacitors contain a considerable quantity of expensive metal tantalum and can be detached and liberated from printed circuit boards by impact breakers. In this study, the size and density distribution of the liberated electronic devices were investigated. Then, tantalum capacitors were recovered from other electronic devices using size separation and pneumatic gravity concentration methods. More than 70% of Newton's separation efficiency was obtained for tantalum capacitors. High Newton's separation efficiency could be also obtained for other types of electronic devices such as chip resistors.

Jan 1, 2011

By F. Chiesa

Experimental results on thin and thick castings poured in aluminum A356 and magnesium AZ91E by the low pressure permanent mold process have been compared to the result of filling simulations for thin and thick castings. If the results of modeling is reliable when the liquid remains above the liquidus temperature, this is no longer the case when partial solidification occurs. The visco-elastic behavior of a partially solidified liquid is difficult to put into equation as it depends on the amount of shear it has been been subjected to. Attempts to predict misruns with a commercial software has been proven to be very difficult if not impossible; divergence of the numerical solution has been observed unless prohibitively long computing times are used. In order to overcome these difficulties from a practical standpoint, a simple method is proposed which consists in tracking the temperature of the advancing liquid metal front so as to make sure it will always be above so-called `Misrun Critical Temperature' (MCT) determined experimentally for thin and thick aluminum A356 and magnesium AZ91E castings. If the liquid metal front falls below this temperature, a cold-shut or misrun is likely to happen at this location. The values of MCT for thin and thick in aluminum A356 and magnesium AZ91E were determined experimentally on misrun castings of extreme geometries (a thin 2.5 mm wall cover and a 6mm to 25 mm thick bell housing). MCT was found to be lower for magnesium AZ91E and for the thicker castings.

Jan 1, 2011