Search Documents

By J. E. Gill, A. R. Byers

The Surf and Pugsley gold-copper mines; owned and operated by Surf Inlet Consolidated Gold Mines; Limited; are about 6 miles inland from; the head of Surf inlet; on Princess Royal island; Skeena mining division; British Columbia. Surf inlet is a fiord 360 miles in an air line northwest of; Vancouver.

Jan 1, 1954

By R. A. Ford

The paper outlines: methods used for the determination of wear metals in motor and transmission oils; contaminents in motor, transmission and crusher lubricating oils; and viscosity determinations. Case histories and costs are presented to illustrate the value of an oil analysis program. Introduction NORANDA MINES LIMITED (BELL COPPER DIVISION) is located on the shores of Babine Lake, approximately 450 miles north of Vancouver, British Columbia. Access to the mine is by road from Topley, B.C., about 40 miles away. When a preventive maintenance analysis program was first considered, it was obvious that if samples were to be sent out for analysis, results would not be available for at least a week, due to the distance from any commercial laboratory. The assay laboratory was asked to investigate the possibility of determining wear metals on site. A limited program was started soon after production commenced, and this has now grown to include all large mobile equipment as well as crushers and grinding mills. The laboratory also now determines viscosity, fuel dilution, dirt and abrasives, glycol and water. All these results are ready within two days. This paper will outline the methods used, data interpretation, several case histories and the benefits from such a program.

Jan 1, 1977

By J. G. Speight

Laboratory studies indicate that autogenous heating of low-rank coal can be prevented by a prior treatment which involves immersing the coal for short (5-15 min.) periods in an inert liquid at temperatures between ~ 350° and 400°C. Such "carbonization" effectively reduces the accessible pore volume of the coal to levels at which heat generation through subsequent sorption of moisture and oxygen is too slow to cause significant temperature rises in a stockpile. In addition, this treatment also irreversibly removes most of the moisture held in the raw coal and raises its calorific value by as much as 10-12%.

Jan 1, 1973

By F. Pinto, C. A. Prato, R. J. Rocca, P. F. J. Huerta Soaje

"The seismic hazard for civil engineering structures is generally defined in terms of deterministic or probabilistic acceleration response spectra at an equivalent rock outcropping. The design of tunnels, however, requires the definition of demands in terms of accelerations at ground surface (near the portals) and in terms of both accelerations and velocities at different depths within the alignment. The design near the portals is controlled by inertial effects and is often times impacted by the possibility of slope instability and rockfall, whereas the design at deep sections is controlled by kinematic effects. These effects are accounted for in practice by introducing deformation patterns in the structure that are related to an assumed wavefield, often times ignoring the effect of the structural stiffness in the response. This paper presents a study regarding the definition of seismic demands for different sections of 14-km long tunnel in the Andes (Argentina-Chile), with a maximum overburden of 1750 m in a seismically active region. The tunnel will pass through volcanic massifs mainly composed by andesites and rhyolites.The study includes the definition of spectrum-compatible seismograms, deconvolution, and definition of accelerations and peak particle velocities for different overburden conditions. A kinematic interaction study for a 500-m tall ventilation chimney shaft is also described, where a simple formulation for the interaction analysis is considered in order to more accurately evaluate shear and bending demands. INTRODUCTIONThe seismic design of linear underground structures, such as shafts and tunnels, generally considers the inertial forces near the shallow sectors (e.g., portals) and the kinematically imposed deformations for the deep sections (e.g., Hashash et al. 2001). The inertial forces are often times evaluated on the basis of design spectra recommended by seismic hazard studies. The kinematic demands for the deeper sections, however, needs to be defined in terms of additional information which is not always indicated by the seismic hazard studies, e.g.; peak particle velocities and accelerations, and their variation with depth. These parameters can be determined by means of a site response analysis, whereby outcrop motions can be deconvoluted in order to evaluate motions inside the ground mass (e.g., Schnabel et al., 1972). Hashash et al. (2001) defines factors that may be used in order to account for attenuation of motions inside the ground mass. However, these factors are provided for depths up to 30 m only, whereas depths of tunnels structures can range up to thousands of meters."

Jan 1, 2015

To determine the optimal circuit configuration for gravity gold recovery consideration should be given to a range of factors in addition to the efficiency of the gravity circuit, including capital costs, ease of operation and impact on comminution. The most common gravity gold circuits utilise a centrifugal concentrator treating a portion of the hydrocyclone underflow. This paper will examine this option and alternative circuit configurations to illustrate the effect of various gravity circuit feed and tailings configurations on the equipment sizing, capital costs, operating costs, water balance, comminution efficiency and gravity gold recovery. The optimum circuit configuration can provide reduced capital and operating costs, maximise gravity gold recovery and improve comminution efficiency.

Jan 1, 2011

By Daniel Hodouin, Bruno Girard, Claude Bazin

"Mineral processing and smelting operations have the reputation of being complex processes. Process operators of these unit operations have acquired from experience and basic training a superficial understanding of the relationships between process output and manipulated variables. This understanding, which is a very valuable know-how for process control and optimization as well as for operator training, is however difficult to extract. This paper describes a time series based approach that can be used to extract this know-how, which can subsequently be used for operator training. The method is illustrated with an example taken from a smelting process.IntroductionThe emergence of Total Quality Management and Statistical Process Control philosophies in the North American industry (Brown, 1991 ), as well as the increasing popularity of the IS0- 900x standard accreditation, provide a strong incentive to review the training procedures for plant operators. The importance of employees training is acknowledged in two of the 14 points of Deming's road to quality (Deming, 1982) as well as by control engineering consultants (Hendricks et al., 1994). However guidelines for the operation of industrial processes are often transferred from an operator to another one with allowance for flexible interpretation of many operating rules. Such transfer is typical of complex industrial processes to which particulate processes of ore dressing and extractive metallurgy belong.Capturing the knowledge of experienced operators is often a difficult task. Cognition engineers are able to extract this knowledge and transfer it into rules that ultimately are implemented into expert systems. Cognition engineers are however not always available and plant supervisors may prefer to keep training as an internal liability. Another difficulty through interviewing of the process operator is its lack of willingness to transfer what he has learned by hard working to other people, whose ultimate goals are to develop computerized applications that may replace him in a near future, or reduce its importance in the production line.This paper shows that time series can be advantageously used to capture the average process understanding of plant operators and to help reviewing training procedures. The method s illustrated with data collected during normal operation of electric arc furnaces and it is shown how the approach has led to a fruitful discussion between process engineers and operators that ultimately provided savings of more that $200,000 per year per furnace. There are 9 furnaces in the studied foundry. Such savings are not the results of application of advanced control strategies nor of ""miracle press button software», but of an improve awareness by engineers and operators of the importance of properly defining the operating procedures to control a process."

Jan 1, 1996

By D. R. Schmitt, N. Ong, R. S. Kofman

Shales and mudstones comprise about 75% of all the sedimentary rocks. In, particular, organic rich shales are considered as a petroleum source rock and more recently with the advent of hydraulic fracturing technology to be a reservoir in their own right. In this sense, the aforesaid motivates our work with laboratory measurements of elastic properties of these geologic materials, which are known to be anisotropic. As such, assuming Vertical Transverse Isotropy (VTI) symmetry, the dynamic and static moduli of a series of cores from various geological formations in Alberta, Canada are simultaneously investigated as a function of confining pressure using the ultrasonic pulse transmission method and strain gages. Dynamic moduli were obtained from ultrasonic P- and S-wave velocities measured on a prism cut with faces perpendicular, parallel and oblique to the assumed vertical axis of symmetry. Static moduli were calculated from strain-stress curves obtained along the directions perpendicular and parallel to the assumed axis of symmetry as well. Velocity measurements show that samples are highly anisotropic, but that the pressure-dependent behaviour of the wave speeds differs. VP(90°) and VSH(90°) both with layer parallel propagation and polarizations change little with pressure while VP(0°) and VS(0°) (both with layer perpendicular propagation) display significant nonlinear responses particularly at pressures < 25 MPa. These characters transfer to the derived full set of elastic constants. In order to effect a proper comparison of the dynamic and static moduli, we convert the dynamic elastic constanst to linear compressibilities pependicular (Kdyn1) and parallel (Kdyn3) which are directly comparable to the static tangent compressibiities obtained by differentiation of the observed strains. Both sets highlight the anisotorpic nature of the material but most interestingly Kdyn1 _ Ksta1 but Kdyn3 > Ksta3 by nearly 40% for one of the samples. The other samples measured respond similarly suggesting that conceptually the structure of such materials could be considered to be constructed of alternating stiff or compliant layers. This finding has implications in the response of the formation to stress particularly during hydraulic fracturing and the interpreation of acoustic logs in providing appropriate measures of elastic properties for engineering purposes.

Jan 1, 2015

By D. O. Tansey

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved.

Jan 1, 1979

By G. T. Lapidus, O. J. Solis-Marcial

Currently, ores with high-grades of copper oxides and secondary sulfides have become increasingly scarce, which has encouraged industry to look for alternative raw materials to obtain copper. The problem is that primary sulfides are difficult to dissolve at near ambient conditions. Proposed hydrometallurgical processes have not been implemented beyond a pilot or demonstration scale. One of the principal disadvantages is that the majority of these processes are not viable with ores that contain less than 4% copper. One of the more recently proposed techniques involves the use of organic solvents in the dissolution of copper concentrates with a chalcopyrite content of between 20 and 30%, which has shown high efficiency. The present research explores the ability of this process to leach copper from low grade chalcopyritic ores (<4% Cu) at different temperatures ranging from 20 to 50°C. It was found that depending on the temperature, high percentages of copper were extracted in 40 to 100 minutes, using different oxidants. Additionally, distinct leaching behavior was observed with each oxidizing agent. In some cases, the extraction kinetics adjusted to the diffusion controlled shrinking core model.

Jan 1, 2014

By C. K. Baxter, A. Odeshi, M. Mohammadi, E. D. Cyr

"Metal additive manufacturing has been a revolutionary step in designing new complex shapes with faster and cleaner building capacity in comparison to subtractive manufacturing processes. The ability to print lightweight alloys such as aluminum has made metal 3D printing attractive to different industrial sector from aerospace to energy and bioengineering. Of particular interest in this study, are the mechanical and microstructural properties of AlSi10Mg-200°C alloys. In this project, samples were 3D-printed in horizontal direction using an EOS M290 machine by Direct Metal Laser Sintering (DMLS) technique. Uniaxial tensile tests and high strain-rate impact e tests were carried out to investigate the mechanical properties and to study the repeatability of the process. A constitutive model is developed to predict the results of the mechanical tests at varying strain rates to better understand the high strain-rate behaviour of these alloys. Using optical microscopy, features such as scan tracks and melt pools within the AlSi10Mg-200°C samples were observed, and the microstructure was observed to be homogenous. The previously listed tests were compared to the results obtained for similar cast alloy counterpart, i.e. A360.0.INTRODUCTION A relatively new way of manufacturing parts is on the increase as rapid prototyping becomes increasingly popular throughout the world. Additive manufacturing is a process which, given a 3D model, uses metallic material in powder form to build a part layer by layer until completion (Gu, Meiners, Wissenbach, & Poprawe, 2013). This way of rapid prototyping is very attractive in comparison to other possibilities because of its ability to accommodate complex design and geometries. Conventional manufacturing methods have limitations when it comes to complex geometries, but additive manufacturing allows for increased design flexibilities while maintaining a light and stable final product (Murr et al., 2012). It also allows for a reasonable cost, especially for small batch sizes that would otherwise be extremely expensive."

Jan 1, 2018

By A. Kobzhanov, S. Saparova, S. Brochot, D. A. Mango

KATCO (an ORANO Mining and Kazatomprom joint venture) is the largest in-situ leach uranium mining operation in the world, exploiting the Muyunkum and Tortkuduk uranium deposits in southern Kazakhstan. After extraction from the deposits, uranium is then transported via a hydraulic network to be purified in three processing plants located near these deposits. Within KATCO, with the support of ORANO Mining and CASPEO, in 2018 and 2019, a large project that had as its main objective to improve the uranium accounting system was implemented. The objective of this paper is to describe this project and all the changes that it entailed. At KATCO plants, a black-box approach was previously used for uranium accounting. However, it is recommended to use all the available measurements and to deploy a data reconciliation model (between well-fields and plant) as the reconciliation uncertainty is overall lower and it provides a more accurate uranium balance. During the deployment of this project, the rules and algorithms to generate the uranium accounting report, the associated flow diagrams (for uranium accounting), the streams, units of operation, stocks, reporting and Key Performance Indicators calculation rules were re-defined.

Jan 1, 2020

By J F. Davies

A review is presented of the fundamental differences between the Superior and Churchill geologic provinces. Structure, lithology, grade of metamorphism and a single recent age determination suggest that the Flin Flon -Snow Lake and Lynn Lake belts are remnant blocks of originally Superior rocks lying within the Churchill province. Major mineral belts occur along the main boundary between the Superior and Churchill provinces (the Thompson -Moak Lake nickel belt) and within the remnant Superior blocks inside the Churchill province (Fiin Flon -Snow Lake and Lynn Lake). During the Hudsonian orogeny, metamorphic gradients must have existed across the Churchill-Superior boundary and between the remnants of Superior rocks and the enclosing gneisses of the Churchill province. It is possible that not only the unusual nickel deposits of the Thompson belt but also the base metal deposits of the Flin Flon -Snow Lake and Lynn Lake districts are due to redistribution, or diffusion and migration of metals to areas of lower-grade metamorphism during the Hudsonian orogeny.

Jan 1, 1964

By John Porritt, Alain Dorval

"TioMin Resources Inc. is evaluating the feasibility of exploiting the heavy mineral sands deposit at Natashquan on the north shore of the Gulf of St-Lawrence, Quebec. TioMin holds the exploration rights to 180 square kilometres, on which 1.6 billion tonnes of sands grading approximately 6% heavy minerals were outlined. The heavy minerals of value include magnetite, ilmenite/hematite, garnet, and zircon. An important part of this evaluation is the development and testing of a mineral separation flowsheet. Under a comprehensive mandate from TioMin, the Centre de recherches minerales (CRM) provided technical assistance to build and operate an on site primary concentrator pilot plant. This plant produced a 93 tonne concentrate, providing over 60 % heavy minerals. This concentrate was shipped to the CRM pilot plant in Quebec City. It was used for further flowsheet testing and for preparation of products and concentrates of heavy minerals with regard to marketing possibilities. This paper presents the flowsheet developed to produce these concentrates.IntroductionIn late 1992, an 11 tonne bulk sample of sand was collected from within the mineralized zone of the Natashquan deposit. This sample was processed over conventional spirals and wet tables at the pilot plant facilities of the Centre de recherches minerales (CRM) in Quebec City. A primary concentrate was produced, from which several 20 kg samples were forwarded to five research laboratories in North America and in Australia. Their tasks were to determine the mineralogical composition of this concentrate and the potential for recovery of marketable minerals from the heavy mineral sands. Satisfactory results obtained from this approach encouraged TioMin to proceed with a more detailed pilot plant program."

Jan 1, 1995

By S. M. Fatemi-Varzaneh

The AZ31 magnesium alloy is considered as a promising alloy in various applications and industries. Furthermore, to design a proper hot working process (rolling, forging and extrusion), the assessment of hot working behaviour of the alloy is necessitated. Accordingly, the hot deformation behaviour of AZ31 alloy was studied through hot compression testing method. The latter was carried out in a wide range of temperature (523 K to 783 K) and strain rates. The obtained true stress-true strain curves and final microstructures were examined and a partial melting was realized at 740 K. It was concluded that the presence of liquid did change the deformation mechanisms thereby affecting the flow behaviour.

Jan 1, 2005

By W. Schubert, N. Radoncic

"The term “squeezing” is frequently used, although it is ill defined. Definitions like “large and long lasting displacements” raise the questions about the threshold values for the magnitude and duration of displacements. Large displacements during tunnelling frequently are observed in fault zones with high overburden. Whether this causes problems very much depends on the design approach used. On the one hand, the magnitude of expected displacements has to be predicted prior to excavation to provide for enough allowance for the displacements without violating the clearance profile. On the other hand, the support characteristics must be compatible with the expected imposed strains. As the magnitude of the displacements and thus the strains in the support depend on the support capacity and its characteristic (yielding potential), only well engineered systems will be successful.Experience in Alpine tunnels over the last decades has shown that closed shotcrete linings can sustain a strain of approximately 0.8% to 1% without failure. Any strain above this value inevitably leads to failure of the lining, and thus a loss of resistance, causing additional displacements. Based on a large number of simulations, a criterion for a critical overburden depth up to which closed linings can be used has been developed. Traditionally open gaps in the shotcrete linings have been used to allow for larger strains. To enhance the efficiency of the linings, yielding elements have been developed, which are integrated in the shotcrete lining, allowing large strains and controlled development of support resistance (Figure 2). When designing such yielding support systems, the development of the displacements, as well as the rheological behaviour of the supports must be considered. As the development of displacements to a large extent depends on the face advance, also the advance rate has to be considered, to be able to compare the time-dependent strength of the lining to the stresses developing as a result of the imposed strains. Another issue is the compatibility of the rock bolts with the large strains. With standard grouted bolts, there is a potential that the “fresh” grout is sheared due to the initially large strain rates. Special rib designs of the bolts allow for a higher strain tolerance.For successful tunnelling through fault zones quality monitoring and up-to-date data evaluation is of crucial importance. With advanced evaluation tools, changes in the ground conditions ahead of the face can be reliably predicted. With the help of empirical relations, the development of the displacements for different advance rates and supports can be predicted, allowing for the determination of the required overexcavation.The paper presents a review of the development of ductile elements, methods of analysis, and monitoring data interpretation."

Jan 1, 2015

By K. T. Aye

An investigation into the leaching of chalcocite and covellite in cyanide solutions at concentrations typically encountered daring gold cyanidation has been conducted. The results indicate that, for both minerals, the extent of leaching is greater under anoxic conditions, but is still incomplete even in the presence of free cyanide ions, with undissolved copper solids remaining in equilibrium with solution species. The speciation of the sulfur and cyanide reaction products in solution are interpreted in terms of the fast formation of a copper(I)- cyanide complexes in solution and a sulfur-rich copper(I) polysulfide solid phase, which then reacts more slowly to produce thiocyanate ions.

Jan 1, 2011

By Jaeheon Lee

"Biooxidation of gold ores or concentrates could be a very attractive alternative to pressure oxidation (POX) or roasting to liberate the gold grains from various sulfides. Crushed heap bioleaching was successful in US and many operations using tank bioleaching of gold concentrate are currently running around the world. Many parameters need to be considered during the project of sulfidic refractory gold ore process. Capital and operation costs are among the most important ones. Run-of-mine heap biooxidation could be very inexpensive and the smaller the crush size (particle size), the more expensive the capital and operating costs for biooxidation application are expected. The capital cost of biooxidation could be a fraction of the cost for building POX plant or roaster and the operating cost could be 1/3 of POX or roasting depending on the method utilized. A new biooxidation process, Sand Farming, is introduced as an alternative to POX and tank biooxidation process. A relatively coarser particle size (P80 = 650 µm) of the process benefits the low cost of grinding against the conventional grinding size (P80 = 75 µm) for other options. The cost of Sand Farming is less than 40% of that of pressure oxidation with comparable gold recovery from the downstream process. This paper will review the laboratory scale testwork for various biooxidation process of sulfidic refractory gold ores and concentrates and provide the economic evaluation showing the biooxidation could be the most economic method without much sacrificing the overall gold recovery. INTRODUCTIONThe decreased availability and lower grade of raw materials has motivated industries to consider recovering values utilizing low cost process options. The process may treat high grade concentrates or submill grade ores that cannot be processed economically by conventional milling-flotation or leaching. Sulfidic refractory gold ores/concentrates have been economically processed by roasting, pressure oxidation, and biooxidation in stirred tank reactor. The process selection is based on a series of studies including multi-year long ore characterization and metallurgical investigations."

Jan 1, 2016

By Stanley Davidson

"The ore deposit mined by Falconbridge Nickel Mines, Limited, is one of the numerous nickel-copper sulphide bodies marginal to the large oystershaped mass of differentiated norite in the Sudbury district, famous as the world's most important nickel producing field. The unique character of the ore deposits of the district has resulted in its intensive geological study over a period of more than 50 years. The results of these studies have given rise to a voluminous geological literature and to a great deal of controversy as to the genesis of the ores. This description of the structural geology at the Falconbridge mine is presented in the hope that it may form a small part of the chain of evidence leading to a reasonably satisfactory explanation of the ore genesis.The mine, named after Falconbridge township in which the deposit occurs, lies along the southeast margin of the norite mass, which, however, is h::re concealed beneath a deep mantle of glacial sands and gravels averaging over 100 feet in thickness. As a consequence, the deposit was not discovered by the early prospectors, and it was not until 1916-17 that E. J. Longyear, of Minneapolis, located the ore by drilling(ll). The discovery was foreshadowed in 1899 by the work of Thomas A. Edison, who found indications of the deposit by what is believed to have been a combination of magnetic and electrical geophysical surveys. He sank a prospect shaft over what has to date proved to be the largest and richest ore section in the mine. A wet quicksand layer at the rock surface proved impenetrable, however, and the 'Edison' shaft never reached bed-rock.The Falconbridge property was acquired by the Lindsley interests in 1928, and ore output, since its inception in 1929, has gradually risen from a modest beginning to the present 2,000 tons and more daily. Total production in this period is 7,500,000 tons of ore averaging 1.72 per cent nickel and 0.89 per cent copper, together with a small but valuable content of precious metals, principally of the platinum group."

Jan 1, 1954

By Ki-Bok Min, Bona Park

"In spite of the applications of DEM models to emulate the elastic modulus, Poisson’s ratio and strengths of isotropic rock in laboratory scale, extensions to anisotropic rock and larger engineering scale still have many challenges to overcome such as robust verification and validation against observed field case. In this study, a discrete element modeling was performed in order to represent a transversely isotropic rock such as shale, and the upscaled model was applied to foundation and borehole problems using PFC2D. The applicability of the upscaled rock mass model was verified by an analytical solution. The DEM modeling of stress redistribution induced by an applied surface line load compares well with Boussinesq’s isotropic solution and anisotropic solution given by Bray. The borehole model with a circular opening under biaxial stress was compared with both isotropic and anisotropic solutions resulting in good agreement. The abilities of DEM model to investigate the micromechanisms accounting for complex macroscopic behaviors and to predict the macroscopic behavior are discussed.The results demonstrate that DEM modeling has the potential to be applied to anisotropic rock mechanics problems on larger engineering scales such as wellbore stability problems especially in shale formations. Furthermore, the effect of anisotropy modeled through this study may be able to explain failure behavior of anisotropic rock encountered frequently in real cases.INTRODUCTIONAnisotropy is prevalent in various types of rocks, especially in shale that contain a set of parallel bedding planes. These weak planes in various forms are sources of large deformation and low shear strength and contribute significantly to the anisotropic behavior of rocks (Amadei, 1996; Cho et al., 2012; Kim et al., 2012). As elastic and strength behavior of anisotropic rock is substantially different from that of isotropic rock, proper consideration of anisotropy is of great importance. There is extensive of experimental evidence showing the anisotropy of shale. Niandou et al. (Niandou et al., 1997) analyzed the plastic deformation and failure mechanisms of Tournemire shale were highly dependent on the orientation of bedding planes. Cho et al. (Cho et al., 2012) presented various deformations and strengths of Boryeong shale obtained from laboratory experiments. Fjaer and Nes (Fjaer and Nes, 2013) performed uniaxial and triaxial compressive strength tests using Mancos shale, and they observed that the shear sliding along the planes of weakness before the occurrence of a major failure can reduce the strength of anisotropic rock. The recent research has demonstrated that the anisotropy of rock is an important consideration in rock engineering."

Jan 1, 2015

By Jose Alberto Gonzalez, Said Sharif Mahboob, Jeffrey L. Shepherd

"During the industrial electrowinning of zinc, uneven growth can cause short-circuits and make the deposits more sensitive to the presence of impurities that can significantly impact current efficiency. To produce levelled zinc deposits, additives such as glue, licorice and sodium silicate are often added to the electrolyte. Even in the presence of additives, uneven zinc growth still takes place because of the combination of hydrodynamic and electrolysis conditions in the cell house. Recent advancements in imaging spectroscopy and scaling analysis have opened an avenue to further study the effects of additives on zinc growth morphology. In this study, Atomic Force Microscopy (AFM) and scaling analysis have been used to monitor zinc growth characteristics including roughness, periodicity, aspect ratios and growth mechanisms as a function of electrolyte composition as well as deposition time. Zinc was electrodeposited from an industrial electrolyte containing a host of additives onto an aluminum cathode with a platinum wire serving as the anode. AFM images of the samples were collected to obtain 3D topographical information on which scaling analysis was performed to extract details on root-mean-squared (rms) roughness, periodicity (grain size), aspect ratio of surface features and growth mechanism. This analysis provided information on the mechanism by which the previously mentioned variables can impact short term growth and also provided a prediction of expected growth at long deposition times.INTRODUCTIONElectrowinning is one of the final stages in the industrial production of zinc metal. It is during this process where dissolved zinc ions undergo electro-reduction from an acidic electrolyte onto an aluminum cathode and are later recovered by stripping the zinc metal from the substrate. However, due to the nature of zinc growth as well as the various operating conditions, zinc deposition may occur unevenly, sometimes causing short-circuits that can cause electrode damage and reduced zinc production."

Jan 1, 2016