Search Documents

By R Zavadil, S Kuyucak, F Fazeli

Proton exchange membrane (PEM) fuel cells generate electricity by reacting hydrogen and oxygen. A thin, bipolar electrode material provides a medium for electron exchange with the electrolyte, alternately serving as anode at the hydrogen-rich side and cathode at the oxygen-rich side. Stainless steels have sufficient corrosion resistance to qualify as bipolar plate materials. However, the protective chromite layer increases the contact resistance, the battery’s internal resistance; and thus, decreases the electrical efficiency of the fuel cell. A heat-treatment is proposed and investigated via simulation by ThermoCalc / Dictra and experimentally, to generate a sufficient quantity of conducting surface carbides that breach the protective layer. Once carbide growth is arrested, a subsequent heat-treatment is also needed at a higher temperature to restore the corrosion resistance by filling-in the Cr-depleted layer (sensitization) around the carbide particles.

Jan 1, 2014

By P. Radziszewski

"The comminution energy curve is a profoundly simple graphical technique that displays detailed operating efficiency information for industrial comminution processes. The database underlying the methodology has recently more than doubled, to now contain a substantial fraction of the international comminution output (1.7 billion tonnes of rock per year) across more than 8 major commodities. This increase has deepened the analytical capabilities and effectiveness for assessing comminution circuit performance in relation to comparable operating mines. This paper will explore how the energy curve methodology can be used to examine the ability of stirred mill technologies to increase efficiency.Specifically, this paper explores how the energy curves methodology can be used to present energy efficiency gains achieved at three mines employing a stirred mill technology under different duties. The first of these cases studies was conducted by Rosa (2014) who compared the performance of two ball mills operating in parallel with a Vertimill in the regrinding circuit at the Samarco Iron project in South East Brazil. The Vertimill was found to achieve the same product specification while consuming 40% less energy. Brissette (2010) investigated the impact of grinding media on the performance of both ball mills and Vertimills. The energy savings achieved varied from 10% to 40% for the ball mills and 30% to 60% for the Vertimills. Lastly, Bergerman (2012) investigated the operating conditions of the Sossego regrind circuit from 2006 to 2011 against design specifications and laboratory testing. The operating work index of this circuit varied from 5.2 kWh/t to 44 kWh/t over this 5 year period. The full suite of energy curves"

Jan 1, 2016

By Robert Martin

New Millennium ?a new project for an experienced mine building team ?Owns 100% of KeMag(Harris Lake) property ?Owns 80% of LabMag(Howells River) property -20% owned by Naskapi Nations of Kawawachikamah ?All founding directors are mining professionals : Geologists or Mining Engineers ?All have extensive experience in the iron ore industry ?The Project Office is located in Montreal, lead by a team of experienced iron-ore professionals Project Overview Geology & Resources Market Prospects Process & Product Development Development Plan Questions

May 1, 2007

By Goutam H. Shahani

Today, the mining and mineral sectors are being impacted by highly fluctuating supply ? demand, extreme price volatility and tremendous market uncertainty on a world-wide basis. This pattern is expected to continue for the foreseeable future. In particular, large consumers of tonnage quantities of industrial gases (oxygen, nitrogen) all have to make informed investment decisions in this uncertain economic environment. Plant owners ? operators need to carefully examine their current and future industrial gas needs in order to develop the most cost-effective industrial gas plant configuration. This can be done by partnering with an experienced engineering company that offers a complete technology portfolio for producing industrial gases. Ideally, the mineral and engineering companies have to work together as a single team to identify the most efficient and economic plant design. This includes an in-depth assessment of capital and operating costs, in order to deliver an optimal solution, taking plant reliability and process safety into account. It is important to consider all the industrial gas needs at a given manufacturing complex, in conjunction with available utilities and infrastructure to develop the best possible long term solution. Oxygen (O2) requirements include: oxygen enriched and oxy-fuel combustion, smelting and hydrometallurgical operations. Nitrogen (N2) is used for annealing. All of these industrial gas requirements have to be examined at a given site over a long term horizon in a holistic manner. Cryogenic air separation was first practiced at a commercial scale in 1902. Since then, the technology has been constantly refined to reduce cost; and improve reliability and flexibility. Today, using advanced engineering techniques, including proprietary process simulation, and modern fabrication techniques, it is possible to build air separation plants that are both low cost and high quality at the same time. It is important to work with an engineering company that owns a complete portfolio of industrial gas technologies, functional engineering capabilities and a variety of plant solutions. Such a partnership can quickly identify a ?sweet spot? for a given situation. By drawing on experience gained from hundreds of projects, it is possible to quickly optimize a given requirement. In situations where a customer wants a complete solution it may be appropriate to provide an air separation plant on a turn-key basis. This will enable the mining and mineral processor to focus on their core business. By using global procurement and construction capabilities it is possible reduce cost and improve project execution, thereby making industrial gas plant procurement simpler and cheaper for the mining and mineral sector.

Nov 1, 2011

By R. E. Gilmore

Introduction The Sydney coal-field extends for a distance of thirty miles along the northeastern coast of Cape Breton island. At a central focal point at the tip of the south arm of Sydney harbour, seven miles or so in from the Atlantic ocean, is the city of Sydney, with Port Morien to the southeast and Sydney Mines to the north . Mining centres along the ocean coast between these points include Birchgrove, Reserve, Glace Bay, and Waterford. The field is divided into three districts or 'basins', namely, Morien basin to the south, Glace Bay in the centre, and the Lingan-Sydney Mines basin to the northeast. The eastern and western portions of the latter are known as the Lingan and the Sydney Mines basins, respectively. Six distinct coal seams are described as existing in the Morien basin, nine in the Glace Bay basin, and six in both the Lingan and the Sydney Mines basin. Although known by different names in the several basins, a definite continuity of the seams has been established.

Jan 1, 1933

By Sylvain Létourneau

Help organizations maximize the benefits of the data that they collect ? perform scientific research in: machine learning, data mining, statistics, artificial intelligence, soft computing, information retrieval, information systems, and natural language processing ? preferred application areas: Equipment Health Management, Bioinformatics, Health, Web Mining ? today?s talk limited to Equipment Health Management While the aircraft is still in the air, IDS: ? clusters relevant WRN, FLR, and snag (pilot) messages ? identifies probable causes based on TSM and provide links to corresponding TSM pages ? assesses MEL conditions (GO, NOGO, GOIF, ?) ? displays relevant maintenance history, suggests fixes based on similar cases ? Commercialization with MxI Technologies Ltd and Air Canada in 2000

May 1, 2008

By Fabien Miller

Automation technologies are increasingly envisaged to improve underground mining productivity. However, the technologies need to be used and adopted gradually in order to get the best benefits. This paper presents the technical and operational aspects of autoguided production vehicles at Brunswick Mine. During 2001 Noranda?s Brunswick Mine has successfully commissioned an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two orepasses. Operational advantages include increased system capacity and enhanced safety and comfort for the operator. The data obtained up to now indicate that the system can operate reliably in mine production

May 1, 2002

By John D. Godfrey

Geological mapping on the Canadian Shield in northeastern Alberta outlined severalgranitoid rock massespotentially suitable as building stone. A particularly attractive prospect, the Chipewyan Red Granite, was subjected to an aerial survey and ground check. The petrologic and fracture characteristics critical for quarrying and use as a building stone were assessed in the course of detailed mapping at two of the most favourable sites. The extension of good rock was tested to shallow depths at one site by shallow diamond-drill coring. , The Chipewyan Red Granite displays a warm red colour, medium grain size and fairly massive texture, and takes a good polish. Deleterious geologic features studied in outcrop and subjected to structural analysis included regular joint systems, quartz veins, pegmatite dykes, basic shear zones and fault zones. Many of these key geologic features are systematic and hence predictable for stone quarrying purposes; other features, such as irregular fracelM tures, are non-systematic and arefar less predictable. The megascopic structural features studied show similar preferred orientations which appear to be collectively related to the tectonic history.

Jan 1, 1979

By G. Papachristodoulou, O. Trass

"Performance data for both wet and dry grinding of materials have been obtained in this novel, planetary ring-roller mill over wide ranges or operating conditions. The Szego mill consists of a stationary cylindrical shell inside which grooved, radially mobile rollers rotate, driven by a central shaft. The mill has several internal design variables such as number, diameter and length of rollers as well as size, shape and pitch oi helical grooves. It is compact, has a high specific capacity, modest power consumption, and can grind many materials down to ultrafine powders. Illustrative data on product fineness and mill power consumption are given along with results from studies on grinding kinetics.INTRODUCTIONThe extensive use and importance of grinding as a unit operation, coupled with the rather low energy efficiency of conventional equipment provide a challenging incentive to investigate novel methods of comminution. Yet, most current development work is taking place in mill performance modelling and optimization, or with various detailed improvements rather than in the field of new equipment development.This paper is a report on the development of a ring-roller mill invented by the late L.L. Szego which embodies several novel concepts. The mill has a broad range of applications, may be operated wet or dry, and can grind materials down to ultrafine sizes with modest energy consumption. It has been developed by General Comminution Inc. in close cooperation with the University of Toronto."

Jan 1, 1986

By S. Zekovic

"The paper gives an overview of the economics condition and strategic business challanges of the mining&metallurgy sector and their possible impact on the future development of the Bor basin of copper in Serbian part of Danube Region. Economics and strategic challanges in the mining& metallurgy complex are emphasized by world economic and financial crisis. An analysis of strategic challanges is undertaken by application of a comprehensive development framework approach. Paper indicates that an economics and evaluation of possible impacts of constraints and challenges for the development of Bor basin shows that it must be included in corporative decision, local and regional plans.INTRODUCTIONRisks are characteristic of every strategic development and business decision-making, so their successful management should be a part of the development strategy of the corporation, especially longterm. Due to the growing uncertainty in the general socio-economic environment, “risk management”, risk insurance, risk control, risk culture, risk optimization are frequently talked about. Among the key risks at a corporate level are the financial risks and risks of the regulative framework, especially in the field of environment and land use. In both cases, it is a question of external risks, which the companies need to relativize and successfully manage. Some companies pay more attention to production risks and search for better solutions in that domain which is not enough (Ernst&Young, 2008). Strategic business risks appear mostly on the macro-economic level, from where they should be” transferred” onto the level of sector economics and action level in corporations. Risk management include transferring the risk to other parts, avoiding the risk, preventing hazard, reducing the negative effect or probability of the risk, accepting some or all of the consequences of a particular risk.The research has included perspective and the general market trend and market positioning of the production and copper processing complex in the world; the impact of the requirements and strategic goals of the EU Directive and Kyoto Protocol on the institutional and other adjustments important for business in this sector; the impact assessment of the regulations important for business in the mining and metals sector, and case study of economics and challenges for the development of mining and metallurgy sector in the Bor basin of copper in Serbian part of Danube region. The analysis has included the identification and assessment of the global challenges on the future development of the copper complex in the miningsmelting basin Bor. Presented results in the paper are part of the research project “Sustainable spatial development of the Danube area in Serbia"" (No. 036036), financed by Ministry of Education and science of Republic Serbia."

Jan 1, 2012

By W. P. Campbell

Foreword At the outset, it should be stated that this paper does not pretend to present a panacea for the ills that 'frozen' wells are heir to, but rather is an attempt to bring to the attention of those whose special concern it is, a little theory and some facts, which have been brought to light recently, in connection with the problem of 'freezing' as it applies to naphtha-producing wells in the Turner Valley field, and to draw some conclusions that follow from the facts discovered. It should also be stated that the investigation is not to be regarded as in any sense complete, but in progress. Doubtless new facts will be brought to light from time to time which may modify present ideas on the subject, but whether favourable or contrary, these will be welcomed, as the purpose of the Department is to secure as complete information as possible of the factors contributing to 'freezing', since this must be the first step to an intelligent attempt to remedy or prevent its occurrence, if such can be done. It is possible, too, that the cause or causes of freezing may not be the same in all cases, but whether this be so or not will have to be determined later as new information comes to hand. Introduction One of the worries which must constantly confront the operators of gas-naphtha producing wells in Turner Valley-although all, fortunately, have not met with it-is the possibility of the occurrence of what is commonly called 'freezing' (going off production).

Jan 1, 1930

By Karl J. C. Harries

"8.1. INTRODUCTIONThe purpose of this chapter is not to provide precedents or examples of provisions, but rather to offer some comments that may be worth considering in the negotiation or review of an agreement. These comments are not intended to be exhaustive. It must also be noted that, although the chapter is written in the context of a common law joint venture, the concepts and concerns for the most part apply equally to a corporation that is owned by only a few shareholders for the purpose of participating in the project held by the corporation.The corporation has the advantage of having much of its organization established by local corporate law, but the particular wishes of the shareholders will appear in a shareholders’ agreement. The principal differences will be surprisingly small, save for the acquisition provisions that appear in a farm-in agreement1 and the substantial portion of the joint venture agreement devoted to creating and organizing the joint venture entity. Where the joint venture agreement refers to venturers and committees, the shareholders’ agreement will refer to shareholders and the board of directors, but both will have to deal with such basic matters as decision-making, default, dispute resolution, first refusals, funding, and carrying out work on the project. For convenience, this chapter usually refers to “venturers”, which may be taken to include shareholders.Negotiations give rise to many varying circumstances and concerns, and the main asset of the negotiator is an open and flexible mind. A desired result can often be accomplished indirectly in circumstances where the other side has adopted an inflexible position on a suggested approach. As precedents and standard forms tend to focus a negotiator’s thinking, they can be counterproductive. It is after the deal has been agreed to that a precedent can be of great assistance to the draftsman.The concepts are arranged in alphabetical order for convenience, not to suggest their sequence or position in an agreement or their relative importance. An agreement should adopt a progression of subjects in what the parties consider a logical sequence to read and work with. However, experience has indicated that it is best to set out in a single article the substance of the deal (i.e. the terms relating to the farm-in and what the acquiring party has to do to acquire his interest), preferably near the beginning of an agreement. The acquisition of the interest is, after all, the first order of business. The joint venture provisions will then follow in a reasonable sequence. It is also worthwhile to devote a single article to any special provisions that may apply during the earn-in period. For example, it may be provided that, although all work is to be done by the acquiring party as operator (with the duty of care, liability, and reporting requirements as set out in the joint venture sections of the agreement), but during the acquisition period, the acquiring party, acting as operator, may be at liberty to do such work as he wishes, without the need for any committee or other approvals, and committee meetings may be suspended.2An agreement is divided into paragraphs and articles to make it easier for the parties to read and understand, and to assist a party in finding “that provision” when the need arises. A comprehensive table of contents will also assist the parties who must work under an agreement. An added benefit of a table of contents is that in preparing it, the draftsman sees the overall structure of the agreement and will often catch and correct flaws."

Jan 1, 2003

By G. A. Van Wielingen

"The conditioning of natural gas to meet contract pipeline specifications involves in the majority of cases in Western Canada, the appropriation of substantial capital expenditures for treating and processing installations. It is therefore of vital importance to the owners and producers of natural gas to arrive at an appreciation of the economics pertaining to the production and surface handling of their gas reserves at the earliest possible stage of field development. The treating and processing of natural gas often results in considerable changes in composition and related physical characteristics between the wellhead and the point of delivery of the saleable gas. This paper presents a general outline of engineering calculations which can be applied in the pre-determination of the effects that surface handling of gas will have on the composition and physical characteristics of sale-able gas. Emphasis has been placed on the calculation of hydrocarbon dew-points, heating values and shrinkages prevailing at the various stages in the surface handling of natural gas. It is believed that advance information indicating the approximate ranges of these physical properties will facilitate process selection and will provide a basis for the estimation of capital and operating costs of process installations."

Jan 1, 1960

By James R. Wickens, David La Rosa, Robert E. McIvor, Adrian Dance

"The comminution circuit at Barrick Cortez Gold Mine uses an open circuit primary jaw crusher followed by a standard SABC grinding circuit. The grinding circuit incorporates a 26’Ø x 11’ SAG mill, an Omnicone 1560 pebble crusher and a 16’Ø x 28½’ ball mill. Both mills are driven by 4500 HP motors.In 2007, several comminution circuit studies were performed to assess circuit performance and map a course for improvement. This paper discusses the results of those studies including an analysis of mine-to-mill opportunities, grinding work index efficiency, and ball mill functional performance. Subsequently, improvements to the circuit were made to enhance operating efficiency. Specifically, improvements to the pebble crusher liner configuration, advanced process control system (expert system) and ball mill classification and ball charge are discussed. In addition, other current and future improvement opportunities are discussed.INTRODUCTIONThe Barrick Cortez property is expanding to include the new Cortez Hills open pit and underground mines. Ore from these new mines will be processed in the existing Pipeline mill facility. In conjunction with ore characterization work, performance of the comminution circuit needed to be quantified. Thus, in 2007, the comminution circuit was surveyed and opportunities for improvement identified.Figure 1 below shows the Pipeline mill flowsheet. It is a standard SABC grinding circuit using an open circuit primary jaw crusher followed by a 26’Ø x 11’ (7.92m Ø x 3.35m) SAG mill, in closed circuit with a Omnicone 1,560 pebble crusher, and a 16’Ø x 28½’ (4.88m Ø x 8.69m) ball mill. Both mills are driven by 4,500 HP (3,357 kW) motors. The SAG discharge screen aperture is 5/16” (8 mm) x 1-1/16” (27 mm) slots. Ball mill circuit classification is done with Krebs D20B cyclones."

Jan 1, 2009

By E. Özberk

Uranium minerals are often associated with iron minerals, and during the hydrometallurgical processing of the uranium ores, iron plays several significant roles. The presence of Fe(III) in solution promotes the oxidative acid leaching for the recovery of uranium. The control of the distribution of impurities in milling and refining is also affected by dissolved iron. When rejected from the process streams, iron usually collects other impurities and contributes to the stabilization of the wastes for final disposal. These roles of iron, as they relate to current uranium processing operations, are discussed in detail, and some broad and historical perspectives are also presented.

Jan 1, 2006

By Renaud Adams, Vladimir Salatic

"The El Mochito Mine located in Honduras, Central America, has produced lead, zinc and silver in concentrates since the 1950s. The paper discusses changes made in both lead and zinc circuits to reduce costs while maintaining production during the recent period of low metal prices.The intent of this paper is to show that sometimes thinking “outside the box” is beneficial for progress. Also, in striving for better metallurgical results we should not forget the basics of flotation. Sometimes the latest trends may not be applicable to the ore we are treating and may not meet the operating cost constraints.A major beneficial impact on El Mochito metallurgy was achieved when the overall grind was coarsened, eliminating the significant percentage of slimes. Switching from two parallel twostage grinding circuits to one circuit with three-stage series grinding has resulted in a significant reduction in power and steel consumption. With minor layout/reagent modifications, both lead and zinc circuits gained not only in retention time but as well in producing better grade products.Of course, the challenges are still there; they exist and only with the full support of operational data collection and metallurgical laboratory investigation success can come. That is why, we as professionals, can never stop in trying to make the most of what we have.INTRODUCTIONThe El Mochito Mine is owned by American Pacific Honduras S.A. de C.V. (AMPAC) a subsidiary of Breakwater Resources Ltd. Of Toronto, Canada. The mine is located in western Honduras, approximately 220 kilometers northwest of the capital city, Tegucigalpa and 90 kilometers south of the country’s second largest city, San Pedro Sula. The mine began operating in 1948 and to date has produced more than 19 million tonnes grading 240 g/t Ag, 3.5% Pb and 7.4% Zn. Production in 2005 was 700,190 tonnes grading 87 g/t Ag, 1.85% Pb and 6.61% Zn.Decreasing metal content in the ore followed by the lowest zinc price on the market in the last 15 years (see Figure 1) has reduced the cash flow and endangered to stop the operation."

Jan 1, 2007

By S. Banisi, A. Haji-Zadeh, A. R. Hasankhoei, M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9m × 2.05m AG (Autogenous) mills (fixed speed) are used in parallel in a dry operation. The test works conducted in a scale down mill with a diameter of 1m indicated that conventionally used "deflector" type liners did not provide efficient environment for grinding. In this research, to improve the grinding efficiency, a new design using low profile end liners incorporating radial ribs of proper height was investigated. In order to determine an appropriate liner design at different operating conditions, a 100cm×10.8cm model mill was used for experimentation. The special design of model mill made it possible to increase the radial ribs height in steps of 6mm up to 18.5mm. The transparent end of the mill enabled accurate trajectory determination by image analysis. The results indicated that the new lower height profile deflectors and 15.5mm-height (14.5cm in industrial scale) radial ribs improved the mill performance while avoiding excessive pressure drop across the mill and wear on the liner. The image analysis showed that the use of new liners increased the distribution of coarse particles across the mill cross section from 28% to 35%. A new liner design was proposed by decreasing the number of liners in each slice from 5 to 4 pieces. The thickness of the inner head liners reduced from 45cm to 30cm and the outer deflector liners replaced by radial ribs. The distance between the feed and discharge inner head liners increased from the original 115cm to 145cm which increased the effective length of the mill by 26%. The new design reduced the weight and volume of end liners by 9% and 23%, respectively. It was predicted that the new liners design increases the mill throughput by 10% and reduces the metal consumption by 20%.

Jan 1, 2016

By Paul Krivokuca

Outline Quinsam Coal Mine ?? Location ?? Mine History ?? Safety ?? Production ?? Hiring 4S Mine ?? Depillaring design ?? Structural mapping, Risk assessment ?? Rock Bolt Design Selection ?? Training

May 1, 2008

By J. R. Goode

Rare earth elements (REE) and their compounds are critical ingredients in numerous necessities of modern life including: the permanent magnets used in electric motors, generators, speaker and hard drives; high performance automobile tires; catalysts; phosphors; optical glass; etc. World production of REE in 2014 was about 110,000 t with about 98,000 t/a being “Light” (LREE) and the balance “Heavy” (HREE). Unlike other mined commodities, the majority of the LREE produced in the world is a by-product and that from a single iron ore mine in China. The balance of the LREE production comes from four REE-only mines, two in China, one in Australia and one in the USA (now on Care and Maintenance basis). The LREE operations comprise very unusual flotation processes and complex hydrometallurgical plants. In contrast, most of the HREE come from a multitude of small in-situ leach operations exploiting a single, dispersed deposit in China using hydrometallurgy alone. All of the current REE operations produce an intermediate mixed REE product that must be separated to yield the high purity, individual, REE required by the market. This paper describes the processes being used to produce LREE and HREE intermediate products and the separation plants used to make the high purity REE compounds that are key ingredients in the magnets in earbuds, turbines, and automobiles; catalysts used in the production of gasoline, and so on.

Jan 1, 2016

By W. G. Hatch

Introduction In November, 1927, a paper was presented at the Annual Meeting of the British Columbia Division by H. A. Pearse(l), in which he described the milling practice at Britannia and set forth the metallurgical results which were being obtained at that time. In the intervening four years, various changes and additions have been made in equipment and practice, which have resulted in marked improvements in efficiency and costs. These changes and their effects are discussed in the present paper. During the past few years two major changes have been made in plant equipment. The first of these was the. elimination of an intermediate crushing stage by discarding two gyratory crushers in favour of two Symons cone crushers. The latter installation-now effects in one stage a greater reduction than was formerly accomplished in two, that is, by the gyratories together with a set of rolls. The second important change in equipment took place when the original M.S. flotation machines were replaced by six Forrester pneumatic machines, so that now the flotation department consists entirely of machines of this type. A number of minor changes and some further additions to equipment have also been effective in raising plant capacity and concentrate grade, while making noticeable reductions in tailing losses and costs of ore treatment.

Jan 1, 1932