Search Documents

By Darryel Boucher, Thomas W. Leadbeater, Raymond Langlois, Joshua Sovechles, McGill University, Zhoutong Deng

"Spiral concentrators are used to upgrade ore based on the density difference between their component minerals. This simple flowing film gravity separator is of interest for the processing of large amounts of material, as found in the iron ore industry. Addition of wash water at different points on the trough of the spiral affects the grade and recovery of the valuable concentrate by affecting the flow of particles within the thin slurry film. This paper shows how radiolabelled hematite (-355+300 µm) and quartz (–1,180+1,000 µm) tracers were used to determine the particles’ behaviour within the slurry film with and without the addition of wash water. The results presented provide a detailed particle flow pattern around a wash water addition point and its effect on the trajectory and velocity of the particles. This information is of interest in building knowledge about spiral wash water injection parameters such as injection location, direction, flow rate and nozzle orifice type (affecting jet shape and velocity).INTRODUCTIONSpiral concentrators are density based separation devices. They are extensively used in the upgrading of iron ore, fine coal and minerals sands (sources of ilmenite, rutile, zircon and monazite) (Wills & Finch, 2016). A spiral unit is composed of a channel of specific profile formed as a helix of 3 to 7 turns around a central structural post. The feed pulp is composed of 15 to 45% solids with particle size from 75 µm to 3000 µm (Wills & Finch, 2016). Throughput of a single spiraling trough can be up to 8 ton per hour and multiple trough unit (up to four trough) can process up to 30 ton per hour for a footprint of around 0.7 m2 (Palmers & Vadeikis, 2010). They are low cost concentrators considering manufacturing of their trough via polymer reverse molding. The energy intensity of a spiral plan is notably small considering the throughput and is mostly related to pulp pumping and final concentrate dewatering."

Jan 1, 2016

By Tamas Kekesi, Gergo Rimaszeki, Tibor Kulcsar

The efficient purification of soldering waste material can be achieved in a single operational step by the electrolytic refining in pure hydrochloric acid - tin-chloride media. The complex formation of the ionic species may offer a beneficial level of natural inhibition. Using the PCR (periodic current reversal) technology, is efficient in affecting the morphology of the cathodic deposit. In order to optimize the process, the investigation of the solution stability and the electrode reactions is essential. The natural tendency of the Sn(II) oxidation and precipitation can be overcome by properly controlling the concentration of the main components and the ratio of Sn(IV)/Sn(II) in the electrolyte solution. Polarization curves were obtained for different concentrations tin and hydrochloric acid. Conclusions referring to the electrode reaction were derived from the overvoltage - current plots. The morphology of the deposit can be correlated with the exchange current density, also determined from the polarization curves. The cathodic current efficiency and the morphology of deposited metal are affected by the distribution of tin species and the principal electrolysis parameters.

Jan 1, 2011

By Yves Gagnon, Nicole Gauthier, Daniel Kelly, Michel Rocheleau

"The Larder Lake-Cadillac Tectonic Zone in Rouyn-Beauchastel area (a 20 km long segment) contains distinct lithotectonic units bounded by artastomosing or sub-parallel shear zones. The gold deposits in the area are located within highly strained portions of E-W striking shear zones. The ore-zones are structurally controlled disseminated and vein-type lodes. They are spatially related either to megascopic z-shaped folds which refold E-W shears, or to areas of intersection between E-W shear zones and late NE-striking faults. Several ore bodies are enclosed within ultramafic rock units or at their contacts with adjacent units. All the lenses are elongated down dip and distributed, both loterally and vertically, ""en echelon"" . The ore zones tend to decrease in size and number away from the hinge zone of the megascopic z-shaped folds.Two main styles of mineralization are recognized at the Astoria deposit and at for most of the deposits in the Rouyn-Beauchastel segments a discontinuous ""Carbonate Ore"" and a more continuous, albitic sulphide-bearing ""Flow Ore"" (terminology used at the Kerr Addison mine).The typical ""Carbonate Ore"" zones are found within strongly arbonatized blocks bounded by conjugate late NE or NNW-striking fralls. The carbonatized blocks display features characteristic of llrittle to brittle-ductile deformation developed in shear zone system. Vein systems in the ""Carbonate Ore"" occur within shear fractures(D R)tension fractures (T), or within brecciated rocks adjacent to NS llrilcing faults. The ""Carbonate Ore"" zones are displaced by numer IU lole E-W, NNE, NW and N-S faults.The ""Flow Ore"" zones are found within predominantly ductile portions of E-W shear zones. The sulphide mineralization is finely disseminated and regularly distributed within mylonitic foliation or associated with veins and veinlets sub-parallel or oblique to the mylonitic foliation, in which case the mineralization is coarser grained. The gold mineralization is a late Archean event postdating the formation of the penetrative fabric, and synchronous with the end of the dextral oblique-slip motion."

Jan 1, 1990

By E. O. Chisholm

Synopsis The colour changes effected in a solution of dithizone by trace amounts of copper, lead, and zinc mineralization provide a sensitive field test for these metals. The method has been used with success by the United States Geological Survey to trace zinc orebodies under residual soils. The dithizone test is used here on samples of non-residual soil overlying a gold-bearing zone in which the gold is associated with disseminated sphalerite, galena, and chalco-pyrite. A gold-bearing zone was successfully traced under overburden ranging from a few inches to five feet in depth by means of this method. The method may prove useful in guiding preliminary trenching through light overburden, by outlining the extent of copper, lead, and zinc mineralization. Introduction The dithizone test affords a rapid, simple, and delicate test for the presence of zinc in soil and water and is suitable for use under field conditions. It has recently been used with success by the United States Geological Survey to outline a zinc-rich area in the residual soil over a primary zinc deposit in Tennessee. The purpose of the present study was to ascertain whether the method could be used to trace a gold-bearing zone, containing associated zinc mineralization, under shallow, non-residual, glacial overburden. The results obtained indicate that the method can be used to guide preliminary trenching in overburden up to six feet in depth. Tests made of the water near lake-shore outcrops also indicate that favourable prospecting zones may be located from the water, within five feet of the shore. It is felt that this simple field test should find a wider use in prospecting, because, under certain conditions, it can outline favourable zones and thereby reduce the amount of blind trenching necessary. The following pages describe the type of deposit tested, the method used, the .results obtained, and the difficulties encountered by a novice in the use of this chemical procedure. The author is indebted to the officials of Nor-Penn Mines, Limited, for their co-operation while the tests were being made; to the late Richard Bouska, Kenora prospector, for helpful suggestions; and to F. W. McCamus, University of Toronto undergraduate student, who ably assisted with the work.

Jan 1, 1950

By D. J. Reddish

The paper describes a case study where numerical modelling has been applied to predict potential risks associated with inflows of water in active mine workings from an overlying sandstone aquifer. The objective of the modelling was to predict the development of strata fractures and strains as the longwall panels were extracted and investigate their relationship to an sandstone aquifer. The numerical modelling study also included the investigation of the effect of mining on a fault that existed close to the start position of one of the panels. The potential effects of mining on the fault were undertaken by parametric studies adjusting properties for the fault and the relative position of extractions, which allowed the mine planner to position the panel layout accordingly.

May 1, 2003

By G. Gauvin

Life span of aluminum smelting electrolysis cells can reach up to 3000 days. During this period, cathode blocks go under various physical and chemical changes that could result in an increase of electrical resistivity. The increase may be due to carbon migration from the cast iron to the steel bars, gap evolution between the cathode block and the cast iron, cathode cracking, etc. This paper focuses however only on the collector steel bar electrical resistivity evolution. To reveal the main phenomena responsible for the electrical resistivity increase, chemical analysis, metallographic and electrical resistivity tests were conducted on two steels bars picked from two Hall-Héroult cells after autopsies. Cathode voltage drop and temperature were measured using electrically insulated internal probes and thermocouples on 16 samples from each steel bar. Electrical resistivity can reach up to 1.21µO-m for a steel bar aged 2505 days compare to 0.142µO-m for steel AISI 1008 at room temperature.

Jan 1, 2011

By Robert G. Boutilier

So far, most social performance monitoring systems have not gone beyond listing the impacts on various stakeholders. Executives have had to rely on intuition to devise interventions that would improve the impacts. This paper describes a survey process, known as the Stakeholder 360 (S360), which eliminates much of the guesswork. The paper reviews key studies showing that raising the levels of communication, trust, and common vision among stakeholders leads to the acquisition of the resources needed to improve the socio-economic situation. Therefore, the Stakeholder 360 measures the levels of these three factors in the relationships between a company and its stakeholders, and among the stakeholders themselves. In a validation study at a gold mine in rural Papua New Guinea, the S360 produced a socio-political ?roadmap? that showed management and stakeholders alike which relationships need more communication, trust, or common goals/vision. Management used the findings to create alliances that helped the government move forward on a regulatory regime for the mine closure. The community used the findings to focus its planning for life after the closure. An S360 survey conducted six months later revealed a decline in dependence on the mine and an overall increase in levels of mutual understanding.

May 1, 2002

By K. Sakai, M. Miyaue, T. Aoki, T. Tani, S. Tanaka, N. Kudo

In the planning stage of a tunnel, due to limited technology in the geological survey and the financial restriction, tunnel supports are often designed from unsatisfactory information, and the tunnel construction is started. Therefore, "Information-oriented construction" is carried out in the construction stage, in which the design is rationally verified and modified by observations/measurements. Moreover, the ground conditions ahead of a tunnel face must be predicted for efficient and safe tunnel construction. The authors have examined effective prediction methods to the ground conditions ahead of a tunnel face under construction of mountain tunnels (Aoki et al., 2010) in view of the established method (Schubert et al., 1995). Though the prediction method of Schubert requires the displacement in the direction of tunnel axis, it is difficult to obtain its accurate data by the electronic distance meter. Then, we have proposed a method that uses tilt sensors installed at the tunnel crown near the face to obtain the slight tilting information. To measure inclination of the tunnel crown, this inclinometer was originally developed as a daily control measurement, such that the geological condition and its possible change behind the face could be detected early, and a steady advance and construction safety could be ensured. This paper describes the method of forward prediction mechanism and advantages of this suggested method. It then presents the typical results of a field verification test at a tunnel under construction and an example of evaluation of the ground conditions ahead of the face based on the 3D numerical analysis in three types of condition changes of ground deformation moduli.

Jan 1, 2015

By D. C. Fraser

Copper occurs invisibly in a geo-logical environment characterized by swampy conditions and an accumulation of forest peat. This swamp, located in southeastern New Brunswick, contains up to ten per cent cop-per (dry weight), in the organic sediments. This occurrence appears unique in that the metal is apparently organically combined in a chelate compound. Unlike the acidic nature of most peat bogs, the pH of the cup-riferous peat is nearly neutral. Analyses of the peat and associated soils have indicated that the bulk of the copper is contained in the organic sediments. It appears that the cop-per distribution is affected by capillarity, evaporation and the growth of frost crystals, and that the copper fixation is effected by organic sequestration resulting in the metal being bound to the nitrogen or oxygen components of the forest peat. While such a fixation mechanism is not definitely established as responsible for the immobilization of the metal, the facts at hand are compatible with

Jan 1, 1961

By Eduardo R. Rodrigues, Ankur Narang, Roberto Federico Ausas, U. T. Mello, Jose Maria Segura Serra, M. R. Lakshmikantha, Ignacio Carol, Kamal C. Das

"Modeling of big faults or weak planes of strong and weak discontinuities is of major importance to assess the Geomechanical behaviour of mining/civil tunnel, reservoirs etc. For modelling fractures in Geomechanics, prior art has been limited to Interface Elements which suffer from numerical instability and where faults are required to be aligned with element edges. In this paper, we consider comparative study on finite elements for capturing strong discontinuities by means of elemental (EFEM) and nodal enrichments (XFEM) for Geomechanical applications. For general fracture scenarios, Oliver et al. (2008) have demonstrated advantages of EFEM over XFEM for including: (a) ease of modeling in any standard finite element code due to the possibility of static condensation, (b) higher accuracy in some cases for coarse meshes, and, (c) a reduced computational cost. However, there has been no work that considers cohesive fractures in Geomechanics. We present a numerical analysis based on a linear constitutive model and linear triangular elements for the bulk and a linear constitutive behaviour for the fault for a representative set of fault planes in a circular tunnel made in rock mass. In the numerical examples we consider both well-traced and bad-traced meshes. We focus on traction profile analysis for both EFEM and XFEM, since that is crucial to understand the cohesive fracture behaviour specially rock joint. Therefore in each case, shear, normal and stress ratio are compared across the two methods along the fault plane. This is the first such work that compares XFEM and EFEM behaviour for Geomechanics problems.For the considered class of problems and the sharp penalization approach without regularizations adopted, it can be observed that accuracy and robustness of EFEM may strongly depend on the fault orientation with respect to the element edges, while, XFEM is independent of fault alignment with element edges. It has been also observed that, with mesh refinement model, stress oscillation completely removed with XFEM however EFEM fails to provide oscillation free results with finer mesh in case bad-traced model. We also performed error analysis and found that in case of bad-traced mesh the average error in the XFEM is 84% smaller than of EFEM and for XFEM the error goes to zero with increasing mesh resolution, while for EFEM the error increases with mesh resolution. Thus, we experimentally demonstrate that, XFEM performs better than EFEM in terms of accuracy and rate of convergence with marginal increase in computational cost. This work hence provides novel insights on the application of XFEM and EFEM in Geomechanics."

Jan 1, 2015

By J. Ellis Thomson

For many years the value of qualitative microscopic investigation has been recognized in both of the fields of pure and applied science. In particular, its aid has been invoked in the determination of rock specimens in thin section, and some at least of the interrelations of minerals present in any one section have been observed and, to a limited extent, applied for the solution of different problems. During the past decade this form of research has also been diverted to the determination of ore minerals in polished section, with some observation of their structural relations. Microscopic research of a quantitative character, on the other hand, while started nearly one hundred years ago, has found but a limited application in petrography and has scarcely been used at all in the more modern science of mineragraphy. This is very largely due to the methods employed, since most of them consumed too much time and were, in addition, too laborious to encourage many workers in their use. The details of procedure for these earlier methods will be found in another paper by the writer, and will be omitted from this discussion as being of small interest to practical mining men.

Jan 1, 1930

By J. Kang

Large-scale land reclamation has been undertaken in Singapore since the 1960s. In the early years, the fill materials excavated from the hills. In recent years, sea sand is the main source of the fill materials. The contractors used to import the sea sand from the neighbouring countries such as Indonesia. However, in early 2000, the sea sand import from Indonesia and Malaysia was banned. Cambodia, Myanmar, and Philippine therefore became the alternative sources for sea sand. Distance between the jobsite and these countries is over 1,200 km, and transporting sea sand from these areas became a critical issue that could affect the contractor?s performance. Figuring out the right combination of transportation means for a longdistance sand transportation would be challenging because of uncertain situations. We developed a stochastic simulation model, using ARENA, to figure out the right quantity of small-size barges, bulk carriers, and loading/unloading equipment, which could help project managers yield the most production for sand transportation. This paper presents how we developed the simulation model, how it was applied to figure out the optimum combination among various size barges, different bulk carriers, and various types of loading/unloading equipment, for the sand transportation project in Singapore.

Aug 1, 2013

By W. G. Scott

IT IS APPROPRIATE that your Institute should have chosen, for its 1956 Annual General Meeting, the Capital City of a province which is making such rapid advances in mining. The railway industry is proud to be playing an active role in this development, expenditures on equipment and railway construction in the Province of Quebec alone in recent years being in ?excess of a quarter of a billion dollars. In looking up some background material for this address I ran across a definition of a mine by Mark Twain, the great American humorist, which I thought might amuse you. He said that a mine was "a hole in the ground owned by a liar". I am sure that if he were alive to witness the enormous value attached to Canada's mineral resources today he would quickly change his definition. Canada's postwar record of mining development has been staggering in its variety and enormity. Historically, only the ?construction of our transcontinental rail ways outranks the largest of three of these development projects - the aluminum undertaking at Kitimat; the Quebec-Labrador iron ore deposits ; and the petroleum and natural gas developments in Wes tern Canada.

Jan 1, 1956

By Tetsuya Yumoto, Toshikazu Shiratori

Information on the elements contained in E-Waste is important from the viewpoint of recycling. We analyzed several components of waste electrical and electronic equipment (WEEE) collected from citizens. The distributions of the minor metals in WEEE were determined with elemental mapping and chemical analyses. The annual change in elemental composition was investigated by analyzing equipment manufactured in different years. The information will be of use for separation techniques required for future advanced recycling.

Jan 1, 2011

By E. Benguerel, G. Monteith, L. Centomo, S. Pelletier

In early 2007, it became apparent that with changing concentrate feeds, the magnesium (Mg) load projected for CEZinc starting in 2009 and beyond would quadruple and overwhelm the current Mg process bleed capacity. A project was started, following design for six sigma (DFSS) standards, to select both the optimal process and to evaluate its target capacity for the Mg bleed circuit. The economic and process risks of under or over-designing while Mg reduction efforts were underway at the mines also needed to be evaluated. This paper describes the project methodology, the impact on the plant, and some potential optimizations for CEZinc's basic zinc sulphate (BZS) Mg bleed process.

Jan 1, 2008

By P. Chu, J. A. Finch

The formation of small bubbles in flotation is usually accomplished by the use of frothers, or sometimes is due to the presence of inorganic salts in the process water. The effective mechanism associated with the presence of these solutes is generally considered to be coalescence inhibition. However, recent work has demonstrated that the presence of frothers and salts also reduces the size of bubble at the initial formation stage. In this paper we adapt the same experimental setup to investigate the time that it takes for a bubble to form; for a known system power input, the energy to form a bubble can then be estimated from the time. The hypothesis is that the presence of frother and salt will reduce the time for a bubble to form, which can be interpreted as an added energy component being derived from the solute. Testing different types and concentrations of frothers and salts, the hypothesis is supported: the mechanical energy required to form a bubble decreases by about 10% in the presence of these solutes.

Jan 1, 2015

By E. Ghali, J. F. Dorion

This paper presents the results of on-going investigations on the influence of corrosion on the performance of support systems in selected underground gold mines. Rock support is exposed to various conditions that can be aggressive. Samples of corroded support were analysed using SEM and photomicrography to determine the main corrosion forms. Tests are on-going in controlled corrosion chambers to qualify and quantify the impact of rock and minerals particles on steel corrosion. As more data become available these relationships can lead to useful information on the choice of support systems and reliable estimates of their longevity.

Jan 1, 2011

By Imre Gombköto, Barnabás Csoke

"Raw material management means not only mining and processing of primary raw materials like ores, but means also collecting and processing secondary sources of raw materials. Recycling is one of the most developing field of raw material management in Europe, and its solutions are derived from mineral processing roots and principals. Complexity and challenges of the field of recycling results innovative solutions of material processing- Since European Union identified 20 raw materials as critical (CRM) due to lack of primary sources within the border of the EU, recycling become more recognised as source of different raw materials. WEEE is the waste streams contains many of the critical elements and along them at least 15 different species of plastics of which recycling is delayed by a lack of effective separation technique. Most paper deals with separation methods based on different specific gravity, triboelectric charge or surface properties of plastic species. Plastics however have differences of thermal properties and thermoplastics, duroplasts and elastomers can be recognised. The experiments described in the paper aimed to determine thermo adhesive behaviour of plastic species often identified in WEEE streams for separation purposes. According to the results, some plastic types as PS, PP. PC or PVC and PET pairs are possible to easily separate from each other, however different additives are changing thermo adhesive properties of most of the plastics that makes industrial process difficult to develop. Along thermo adhesive behaviour, combination of physical interaction can be used to enhance separation selectivity.INTRODUCTIONPlastics has a relatively long term of history as a light, multi-functional material in construction, packaging, automotive industry and electric and electronic products. There are a numerous types of plastic species can be used for various applications therefore they amount are growing from year to year. This quantity however become part of the waste stream and while metal recycling has been done for decades due to its economic value - cheap plastic parts are less desirable as secondary products. In 2013 an annual 5% of plastic production growth has been estimated with a base data of 265 million tonnes at 2010 (Guiqing & Zhenming, 2013). Since landfill requirements are increasing while—especially in Europe where actual regulations are trying to deflect waste from landfills - landfill capacities are decreasing, costs are become more and more expensive, Applications like energy production based on plastics as a fuel or recycling are some of the options can be applied. Direct incineration of plastics are applied at many plants - in most cases where waste consist of dangerous substances are incinerated because plastics high calorific value helps correct average mixture composition enable operators reaching high enough temperature for combined power and heat generation while most of substances—like PAH, PCB or dioxins—are destroyed. Another path is using low temperature reductive cracking due to pyrolysis process, however the chance having higher concentrate of carcinogen substances in the products are higher since it applies around 400°C during the process."

Jan 1, 2016

By R. St. C., G. E. Morris, M. Zbik, Smart

Effective flocculation and dewatering of slurry streams containing clays (particularly kaolin and smectites which are often <200nm in lateral dimension) is becoming increasingly urgent. Release of water (often >75 wt%), for recycle and reduced make-up water consumption, from slurries in tailings streams and dam beds is usually slow and incomplete. Changes in settling rates and solids density of tailings containing clays can be achieved in practice by changes in pH, dissolved cations and flocculant additions. To achieve fast separation of clays from water and minimization of retained water, individual particles need to be bound in the initial stages of thickening into large, high-density aggregates, which may sediment more rapidly with lower intra-aggregate water content. Quantitative STIMAN (STructural IMage ANalysis) cryo-SEM imaging, shows that the structure of aggregates formed before flocculant addition has a determinative effect on these outcomes. Without flocculant addition, 4 stages occur in the mechanism of primary dewatering of kaolinite: initially separate particles and aggregates are dispersed (<0.3GP, where GP is the gel point); a partially-gelled chain network then forms linking particles edge-edge (EE) still well below the OP but remains largely suspended; after an induction time, this network structure rearranges from EE to face-face (FF) contacts densifying, compacting and dewatering the aggregates with settling rates well above Stoke&apos;s Law estimates for >20µm particles or aggregates; the GP is rapidly reached during settling producing a network spanning the vessel with compressive strength. This sponge-like structure with EE oriented particles limits slurry dewatering because the steric effect in the resulting partially-gelled structure is much more dominant than the electrostatic effects predicted by DLVO theory. Van der Waal&apos;s forces at very close distances, as particles slide across each other, may be responsible for the EE to FF change in structure. In this way, the previously extended network contracts, and when the solid volume fraction is low, the continuous network breaks apart forming aggregates and aggregate associations as flocs which arc able to freely settle. These densified aggregates settle at increased rate, give lower bed density and retain less water after drainage. With flocculant addition, the internal structure and networking of the pre-aggregates is largely preserved but they are rapidly and effectively bound together by the bridging action of the flocculant(s). The STIMAN analysis shows that there is a inverse correlation of intra-aggregate porosity (and void permeability) with Darcian permeability (and extent of dewatering) whereas there is a strong positive correlation of Darcian inter-aggregate permeability with settling and primary dewatering rate.

Jan 1, 2004

By Georges Houlachi, Akram Alfantazi, Maysam Mohammadi

Manganese ions in zinc electrowinning electrolytes form a protective MnO2 layer that ultimately decreases Pb contamination in the zinc product. In this study, the effect of dissolved Mn2+ on the electrochemical performance of Pb, Pb-Ca and composite Pb-MnO2 anodes was investigated. The properties of the MnO2 layer formed on these anodes were studied and compared. Potentiodynamic polarization and cyclic voltammetry experiments were performed in 180 g L-1 sulphuric acid to study the electrochemical reactions occurring on the anodes. The anodes were subjected to galvanostatic polarization at 50 mA cm-2. The morphology and uniformity of the MnO2 layer on the anodes were examined using scanning electron microscopy (SEM). Experimental results revealed that the MnO2 layer formed on the composite anode was more compact and uniform compared to that formed on the Pb and Pb-Ca anode. It was also observed that the cell mud formation rate, and consequently manganese ions consumption, depended on the anode type. Although initial formation of the MnO2 layer decreased the oxygen evolution overpotential, its growth might negatively affect electrocatalytic activity of the anodes.

Jan 1, 2014