Search Documents

By P. Nayak

"Comminution is an energy intensive and expensive process consuming approximately 40-50% of the total processing costs in a mining operation. This process poses an even greater challenge with gold ores due to their low elemental concentration and small particle size. Over 99.9% of the ore fed to the mill is waste which must be removed during the ore processing stage. Preconcentrating the Run of Mine (ROM) ore before feeding the mill will result in significant cost savings. In partnership with Sacré-Davey Engineering, Agnico Eagle Mines Limited identified this opportunity and is currently evaluating the implementation of sorting technology to preconcentrate the ore or upgrade the waste material at its operations. This paper will discuss the steps adopted by Agnico Eagle in the evaluation and installation of sorting technology at its operations. Since the Company has a large portfolio of operations, the first step in the project was to shortlist the operations that had the highest probability for successful application of the technology. Following this, the top three operations were selected for bench scale evaluation. The projects which showed the most economic potential were then considered for detailed evaluation and pilot plant installations. This paper provides an insight into the methodology followed by Agnico Eagle and Sacré-Davey in the evaluation of the technology.INTRODUCTION The benefits of ore sorting technology are being increasingly understood by the mining industry today. The application of ore sorting in gold mining is attractive due to the nature of the mineral distribution. The presence of high value minerals distributed in an extremely small mass of the ROM ore creates a tremendous opportunity for preconcentration with ore sorting. Since Agnico Eagle currently has a portfolio of eight operating mines and numerous development projects and exploration properties, the challenge was to identify the deposits which had the most favourable mineralogy and grade distribution for successful ore sorting. The success of ore sorting is mostly based on the minerals present in the deposit and the grade distribution. The minerals signify the amenability of the deposit for ore sorting and the kind of sensing technology to be used. On the other hand, the grade distribution demonstrates the amount of material that can be rejected without losing value. In order to understand a deposit’s characteristics, it is important to examine the sample’s behaviour with various sensors and then assay it to know its actual value. It is a common practice in the mining industry to document assay value of drill cores and/or material feeding in and out of the mill. However, those VALUES (are insufficient to understand the grade variability on a granular basis. To capture the ore variability in very high resolution and significantly improve the selectivity of the material feeding the mill, it is vital to assay the samples on a rock-by-rock basis, as this is the level of resolution which will be examined by the ore sorter during sorting. A careful and elaborate procedure was followed in evaluating the technology at Agnico Eagle’s operations which is discussed in this paper."

Jan 1, 2019

By J. W. Bingay

The expansion of the mining industry, with other industries, of course, is dependent upon a supply of fresh capital from year to year. Mining is a speculative form of investment, though there is a wide range of risk as between indiudual undertakings. All of the leading financial writers, nowadays, agree that expansion is being seriously interfered with by the unprecedented load of taxation Canadians are carrying. Individuals have less for investment and corporations are obliged to defer necessary expenditures in order that the demands of the taxing authorities may be met. Naturally, speculative investments such as mining exploration suffer first. Undoubtedly, a great deal of cash raised by taxes, if left in the hands of individuals and corporations for investment and expansion, would have been far more beneficially used and would have developed the country more than any use made of it by the government, in the way of bonusing new industries, or the undertaking of large schemes of development. Government undertakings of this nature are often entered into without a proper knowledge of cost and probable return. Expert expenditure of the same sums by business men or corporations undoubtedly would generally produce more prosperity for the country as a whole. The absolute necessity for lower taxation is being increasingly known to the public at large, and eventually it is hoped that our governments will see the economic impossibility of continuing the present rate of expenditure. The successful Finance Minister of the near future will not be the one who can borrow the most money.

Jan 1, 1924

By W. J. Wright

Summary Statement The following notes on the geology of the Grand Lake coalfield are intended to be introductory to a second paper being read at this meeting, which paper will describe the earlier and the more modern mining methods. The coal industry of the Grand Lake coalfield is centred chiefly within a three-mile radius of Minto, but minor operations are dotted over an area of approximately 50 square miles extending easterly to the vicinity of Chipman and Coal Creek (see Figure 1). The coal comes from one seam of Pennsylvanian age. The seam varies in thickness from 16 to 30 inches and lies almost horizontal at depths of 0 to 125 feet. It has been mined and prospected over an area of approximately 150 square miles, but in a portion of this area the commercial possibilities have been destroyed by erosion. The industry is the oldest of its kind in North America, but it did not at tract particular publicity until about 1914. Since that date, mining methods have improved and the output has rapidly increased until, in 1934, it amounted to 271,335 long tons, and furnished employment for about 1,000 men (1). Approximately 73 percent of this amount was produced by the Minto Coal Company, the Miramichi Lumber Company, the Avon Coal Company, and Welton and Henderson, and 25 per cent by the Rothwell Coal Company, Harvey Welton Limited, G. H. King, the Reade Construction Company, and the Newcastle Coal Company. The remainder was produced by J. W. Carter, G. D. Crossman, T. H. Swift, C. S. Yeamans, and several other small operators. The coal is won by underground mining, except in the case of the Reade Construction Company, and a minor operation by Ashfield and Pieton, who have employed open stripping. It is mined only as required to fill definite orders, and is loaded directly into cars for shipment. In 1934, the larger mines did not operate full time, and the production could easily have been increased if markets had been available. The coal is sold in four grades: screened or lump, run of mine, slack, and stripping. The chief market is with the railways and commercial plants, with a fair amount for domestic purposes.

Jan 1, 1935

By E. Herrera, L. Mariscal

"Ilo Copper Smelter operates since 2007 with an ISASMELTTM furnace as a single smelting unit (1,200,000 tpy) associated with two Rotary Holding Furnaces for separation of matte and slag, and which directly produces a discard slag. Southern Peru continually has been improving the slag chemistry of its ISASMELTTM furnace in order to reduce copper losses, given its big economic impact due to large slag mass generation. The present paper describes the influence of the CaO, Al2O3 and magnetite content in the slag of the ISASMELTTM furnace correlated with the SiO2/Fe ratio and its liquidus slag. Also it defines the best slag chemistry and operating practice in order to reduce the copper losses without compromise the bricks life of the furnace.INTRODUCTIONIlo Copper Smelter of Southern Peru (Grupo Mexico) is located on the southern coast of Peru, and treats mainly copper concentrates produced in its own mines (Toquepala and Cuajone).The modernized smelter was commissioned in 2007 and operates with an ISASMELT™ furnace as a single smelting unit (1,200,000 tpy), which is associated with two Rotary Holding Furnaces (RHF) for separation of matte and slag. This slag is directly sent to the dump. Figure 1 shows the smelter flow diagram.The ISASMELT™ process is a bath-smelting process using a single lance. The lance tip is immersed into a molten slag bath contained within the stationary, vertical, refractory-lined ISASMELT™ furnace. The injection of oxygen-enriched air, through the lance into the slag results in a highly turbulent molten bath. Feed material falling into the turbulent bath from above reacts rapidly, resulting in extremely high productivity for a relatively small bath volume."

Jan 1, 2012

By P. J. Mackey

"The metal producing industries in Canada and in the U.S. in many ways owe their technical beginnings to Welsh technology. The first copper smelter in Canada started in 1849-50 with a Welsh reverberatory furnace and skilled furnacemen brought across from Swansea to operate the equipment1- The Rocky Mountain smelting industry began with the installation of furnaces resembling the Swansea smelters(2). It was only later that the North American industry developed newer and improved methods. This article briefly describes the metallurgical history of the Lower Swansea Valley, being that section of land stretching northward from Swansea along the banks of the River Tawe, and bordered by hillsides east and west of the river. The Valley has had a classic cycle of development and decline common to industrial areas of Britain which grew in the Industrial Revolution. Perhaps more than any other area today, the Swansea Valley represents a complete cycle of use from agricultural to the peak of industrial development through to decline and dereliction. The conditions which made the Tawe Valley attractive to certain industries were laid down nearly 300 million years ago with the Carboniferous swamps and forests which covered the area, later forming the south Wales coalfield. As a result of glacial action and the deposit of glacial outwater and alluvial gravels, the valley adopted the traditional configuration, with its rocky sides occasionally remaining exposed. Up to probably about the 16th century, the Lower Swansea Valley was similar in use and appearance to many other valleys in the region. From the 14th century, the natural oak woodland had provided a continuous source of timber to produce charcoal for iron making as well as for structural purposes. Agriculture was the main activity in the valley in this period, but it was likely that the farmers also mined small amounts of coal by way of ""bell pits"", and adits into the coal seams."

Jan 1, 1999

By S. Devereaux, P. Gover, S. Everett

Having real-time data of blast furnace burden profile with respect to burden height and temperature is critical to making informed decisions on blast furnace operation. Given the high temperature and gaseous environment within the blast furnace shaft, traditional instrumentation has been limited at providing the level of real-time feedback information needed to optimize blast furnace operations. Infrared thermal imagery technology provides non-contact temperature measurement across the entire burden profile, allowing for better understanding of the dynamic movement of the burden within the blast furnace shaft. This technology increases blast furnace performance by improving the decision-making process for hour by hour operations. This paper will discuss the development of incorporating infrared thermal imagery technology into the operating strategy of a lead blast furnace.

Jan 1, 2015

By Guy Demers

"This paper defines the responsibilities and functions of the Maintenance Department, and its organization, physical and human assets, highlighting the unique operating problems. Due to the self-sufficient aspect of the Asbestos Hill Deception Bay project, the Maintenance Department cover-s fields that are numerous and very dissimilar: production, mobile, processing, service, power generation, fire protection, heating, water and sewage disposal equipment. Added to this, buildings, plant and camps, wharves and communications equipment all demand versatility, adaptability and expertise from maintenance personnel. Good maintenance practices are a necessity in this environment and are more critical than at southern locations; that is, high-quality replacement material, complete and well-controlled preventive maintenance, major repairs on a component-replacement basis, updated inventory, efficient training and permanent contacts with suppliers, combined with an equipment improvement program, updated specifications on lubricants, hoses, seals, filters, etc., are mandatory. The seasonal aspect of the operations applies a great deal of pressure on the maintenance team, as the production months do not permit major repairs. Short- and medium range planning and accurate evaluation of equipment conditions highly influence production efficiency. Maintenance control, planning and scheduling do not follow the accepted standard routines, as personnel turnover normally does not permit an accumulation of knowledge of the equipment history and condition by the •individual tradesman."

Jan 1, 1976

By J. C. Hawkins

Determining moisture content and rate of flow of a solid product make measurement and control of dryers unusually difficult. This paper de-scribes a method of accomplishing this with readily made air-temperature measurements. The system can cope with changes in feed moisture and feed rate. It does not measure solids temperature. The system's application to several typical rotary dryers is described, and control schemes using feedforward techniques are explained.

Jan 1, 1971

By Y. Tanaka, M. Maeda, S. Suzuki, C. Tokoro, T. Kato, K. Muto

Boron (B) co-precipitation was investigated with ettringite to establish a cost efficient method of removing B from acid mine drainage. For 25 mg/L of B solution, most appropriate pH for B removal was pH 11.5. The most appropriate amount of reagent for B removal within Japanese effluent standard (10 mg/L) was B:Al:Ca:SO4 = 1:3:9:4.5, which corresponds to the composition of Ettringite (Al:Ca:SO4 = 2:6:3). The effect of silicate, carbonate and temperature on efficiency of B removal is important as groundwater and hot spring water are often contaminated. When silicate and carbonate are present, more Al and Ca salts are needed for B removal since some aluminum and calcium precipitate with silicate and carbonate as kaolinite and calcium carbonate. These precipitates do not contribute much to B removal. As the temperature raised, the most appropriate pH for B removal decreased. B removal became less efficient as monosulfate precipitated more rapidly as ettringite.

Jan 1, 2015

By Hiroyuki Sano, Hiroshi Chida, Katsuya Toda, Takafumi Sasaki

Saganoseki Smelter & Refinery is one of the largest copper producers in Japan to produce 450,000 tons of new copper annually. Saganoseki used to operate six PS converters with "4 Hot-2 Blow" scheme, but managed to change its operation to "3 Hot-2 Blow" scheme with four PS converters, while maintaining the same production capacity. To achieve the operational change, the following improvements have been carried out; 1) Extending service life from 220 to 350 batches, 2) Shortening cycle time by increasing the blowing rate and the matte grade, 3) Reducing environmental impact by applying sophisticated fugitive gas collection system and 4) Saving energy by waste heat boiler’s modifications. The operational change has been successfully executed, and results in drastic productivity increase and cost reduction. Currently, Saganoseki is maintaining the efficient and consistent operation with 4 PS converters. This paper describes the above-mentioned improvements for increasing productivity and the recent operational conditions of the PS converters.

Jan 1, 2015

By A. Pearson, F. A. Auld, S. O. Colbeck

"""The theory of buckling of shafts and Steel tunnel-linings"" was published by E. Amstutz in 1970 and commented on by S. Jacobsen in 1974. The authors have revised and enhanced Amstutz’s work to address Jacobsen's comments on its limitations and to extend its validity over a wider range of pipe/shaft geometries, including those commonly found in deep mine access shafts. The author has looked at Amstutz’s assessment of strengthening with flexible shear anchorages and adapted the theory of non-linear shear deformation response of bolts to develop a method of assessing increased buckling capacity utilising the full plastic shear capacity of studs. INTRODUCTION “Amstutz Buckling” refers to the buckling of pipe embedded in concrete under external uniform pressure. In terms of a mining environment, this relates directly to the design of a watertight shaft. This load case will commonly occur where a main shaft is cast against a geostatically stable primary liner and the only load applied to the final shaft is that of a uniform ground water load. Ernst Amstutz wrote his first paper on buckling of pressure-shaft steel linings in 1950 and subsequently improved his theory (Amstutz, 1970), which was then widely adopted for use within the industry. Years later, an alternative approach (Jacobsen, 1974) was proposed. Within his paper Jacobsen critiques Amstutz work, identifying some mathematical inconsistencies and highlighting limitations of the theory imposed by approximations adopted by Amstutz. Despite these limitations Amstutz work has still been used as the favoured design theory for use in the mining industry. In reviewing this body of work the author realised that with the advent of readily available computing software it was possible to adopt an iterative approach using Amstutz approximate formulae to find a solution to the original precise formulae, thus eliminating the limitations highlighted by Jacobsen The shear deformation to load characteristics of bolts has long been established (Crawford & Kulak 1968) and used for the plastic design of bolted connections in shear. This relationship is directly transferable to the design of shear studs, typical properties are well known, and actual values easily established in simple lab tests. The author has taken this relationship and modified Amstutz theory (Amstutz, 1970) for shear anchored strengthened liner buckling, to give a more efficient solution, using readily available material properties."

Jan 1, 2019

By M. A. Upham

"MINING is Canada's second largest basic industry, producing material with a gross value of 2.5 billion dollars, led only by agriculture with 2.9 billion dollars. It pro-vides employment, directly and in-directly, for three quarters of a million people. Since the Second War, the value of mineral production in Canada has tripled. Economists forecast that over the next 15 years its value will triple again. Canada is a basic and leading supplier of nickel, iron, copper, zinc, lead and uranium. It is also a major oil producer, leads the world in the production of asbestos and in five years will be the leading producer of potash, a basic constituent of fertilizer.It can be seen that Canada's wealth and economic progress lies in being a primary producer of economic minerals and in building secondary industries to manufacture finished products from these raw materials. Canada's future in the field of mineral production looks bright, with our resources just starting to be tapped. Outside of the large expanse of Soviet Russia, we are by far the world's most fertile mineral exploration area."

Jan 1, 1967

By W. H. Miller

Introduction In this paper we have endeavoured to present a general description of the electrical applications underground at Copper Mountain, including types of equipment used, problems encountered, and methods by which they were overcome. No attempt has been made to outline in detail the wiring of various circuits. Until recent years, the main use of electrical energy underground at Copper Mountain consisted of direct current for locomotives, trolley systems, .and signal and communication circuits. The prohibitive cost of equipment and distribution systems prevented any extensive use of a.c. beyond that commonly used for essential lighting purposes. However, in 1943 the shortage of manpower and the increased cost of labour and supplies necessitated a general mechanization programme.

Jan 1, 1951

By R. H. Wallis

Weighted moving-average contour maps have been constructed for molybdenum, copper and zinc using 7850 stream-sediment samples from 5430 square miles (14,063 sq. kms) of south-central British Columbia. Regional trends for molybdenum and zinc are northeast, north and northwest and those for copper are north and northwest. These trends are interrupted by zones markedly low in metals . The metal-rich trends cross rocks of different lithology and age and thus appear to be structurally controlled. The northeast trend may have exerted control on metal distribution at two different times.

Jan 1, 1978

By Y. A. Topkaya

In this research work, a process was described for the recovery of copper and zinc in copper converter flue dust from the Black Sea Copper Works' Samsun Smelter Plant. After characterization of a representative flue dust sample, the process included roasting of the flue dust and then leaching in dilute sulfuric acid solution. Roasting time and temperature were studied to determine the optimum roasting conditions. Sulphuric acid concentration, duration, temperature of leaching and solid to liquid ratio were the parameters studied in the bench scale laboratory leaching experiments.

Jan 1, 2007

By M. F. Goudge

THE present century has witnessed an amazing transformation in the uses of limestone. From being mainly a structural material, a role it has played since the beginning of civilization, it has become one of the in-dispensable raw materials for use in the great chemical and metallurgical industries that play such a vital part in the economic life of the nations today. Its uses have become so diversified and numerous that it enters, directly or indirectly, into nearly every phase of modern life. In this introductory paper it is proposed merely to outline the general usefulness of limestone and to point out some of its salient features, and to leave any detailed discussion of uses to the papers that follow. The term limestone as herein used embraces all kinds from the variety known as high-calcium limestone, which is composed almost entirely of calcite, to the dolomitic variety, composed largely or entirely of the mineral dolomite. Lime is simply calcined limestone and, in considering the uses of limestone, the uses of lime should also be included, particularly in view of the fact that, in many processes, it is possible to use limestone in either the raw or the calcined state.

Jan 1, 1939

By Jeonghwan Kim

Intelligent Excavation System (IES) has been considered to be one of the desirable solutions to improve the productivity, quality and safety of the current earthwork processes. IES is composed of various hardware and software modules including task planner (work command generator), local and global work environment sensors, GPS and other sensors to acquire the excavator?s status, robotic controller and electronic valves, and the manipulator (excavator). A data communication manager was required to coordinate the signal or data-flow in between these modules considering the operational status of IES such as; excavation start/completion, truck detection, terrain model update, emergency stop, local sensing, GPS/motion sensor data handling, and so on. This paper presents the role and functions of this data communication manager. After every possible operational status of IES operation was identified, a protocol of each communication process in the form of string-type was made. The components of IES are connected with either wired or wireless network. Therefore, they can communicate with the manager using socket (TCP/IP) communication. The data communication manager is also capable of accessing a web-based project management information system, which constantly updates the performance of excavation robot to online database.

Aug 1, 2013

By B. P. Verma, K. N. Sinha, N. M. Raju, B. Singh

The paper describes a new method of grouting bolts developed at the Central Mining Research Station at Dhanbad in India. This method makes use of wire-mesh sleeve instead of the expensive metal tube to insert the cement mortar into the drill hole. The field trials confirmed that the method is cheap and an effective system of support.

Jan 1, 1972

By S. Beskri, N. Geoffroy

When metallurgical plants are designed, a lot of consideration is almost always given to material selection and possible damage mechanisms. Materials engineers are generally involved and will strive to select optimal alloys or refractories for the design conditions. Once in operation however, things often change. Equipment is overstressed to increase production, corrosive leaks are not always promptly addressed, proper welding procedures are disregarded, etc. This paper describes various cases from the mining and metals industry where serious mishaps, associated consequences, and costs could have been avoided if simple and proactive steps had been taken. It also presents a strategy, based on safety reviews, to help predict and prevent damage to critical pieces of equipment.

Jan 1, 2015

By P. Simon, G. Falkinger, G. Angerer, B. Gerold

"This contribution presents an investigation of the evolution of shrinkage pores during hot rolling with a special focus on the microscopic mechanism. The reliable closure of pores, which inevitably occur during the casting process, is of crucial technological importance for high-quality hot rolled plate products. Therefore, lab-scale tests were carried out under different typical thermomechanical loadings. Extensive data from optical microscopy was collected before and after deformation. The analysis shows that the average volume of pores evolves similar to the volume of an idealized arrangement of voids in an ideally plastic matrix. The average shape of the shrinkage pores, however, was found to be almost constant during deformation. Even though individual pores exhibit complex morphologies far from any idealized geometries, the overall evolution of a large number of pores is well captured by simple assumptions. In addition to the quantitative analysis, a schematic representation of this counter-intuitive behavior is provided. A simple ‘Gurson’-type void evolution equation was implemented in a three-dimensional Finite-Element model of the industrial hot rolling process. With the help of this mechanism-based process simulation the thermomechanical closure of shrinkage pores during the rolling process has been optimized for a variety of plate products.INTRODUCTION Aluminum alloys of the 7xxx series are widely used in the aircraft industry. They have to meet high quality standards regarding microstructure as well as mechanical properties. For hot-rolled aircraft plates, one of the most important quality requirements is that they are free from pores. Pores, however, are inevitably created during the casting process either due to shrinkage or due to the dissolution of gas from the melt. The pores have to be closed mechanically during the hot-rolling process. Therefore, the mechanism of so-called pore closure or void closure has a high technological relevance for the production of aircraft plates. The behaviour of voids in a ductile matrix subjected to mechanical deformation has been extensively studied, especially in the context of damage mechanics. A recent review (Besson et al., 2010) on modeling methods for ductile damage gives a good impression on how much experimental as well as theoretical effort has been dedicated to the problem of void evolution under mechanical loadings. Although void closure has been studied to a far lesser degree, it obeys to the same general theoretical evolution laws as void growth. The most basic theoretical result is that hydrostatic pressure drives void closure, while hydrostatic tension leads to void growth. The mechanism of void closure depends on the void shape. This is illustrated by the example of a flat penny-shaped void, which under compression obviously closes much faster than a sphere with the same volume. Theoretical models have been developed for the evolution of simplified void geometries, such as spheres or cylinders (e.g. Gurson, 1977), spheroidal (Gologanu et al., 1997) and ellipsoidal voids (Ponte-Castaneda, 1994). In industrial cast ingots, however, the pores exhibit very complex morphologies, which are far from any idealized geometry. X-ray tomography revealed ‘tortuous’ voids in a 5xxx aluminium alloy (Chaijaruwanich et al., 2006)."

Jan 1, 2018