Search Documents

By Orlando Rojas, Javier Pizarro, Romke Kuyvenhoven, Francisco Soto

"The concept of geometallurgy has been extensively mentioned and used in the mining industry in the past years. However, each mining firm has a different understanding of what geometallurgy means, and its actual value varies significantly from site to site. Even in the case of properly constructed geometallurgical models, it is fairly common to observe a sub-utilization of the model in the actual operation, because of its low production forecasting capability on the short term. This disconnect between the geometallurgical model and operations is typically caused by a lack of tuning between the original model and the actual plant operation. Also, the absence of procedures and other standards for reconciliation, affects the confidence and the predictive quality of the model. The geometallurgical model should consist of three different levels: (I) adequate capture of information, (II) data analysis and modelling, and (III) development of the block model. Once the geometallurgical in-situ model is finalized, a process model should be developed of the plant at industrial scale, in order to scale up the in-situ geometallurgical parameters from their base or standard condition, to the actual operating reality of the plant. Finally, the stage of reconciliation will close this process, assuring that any deviation between the geometallurgical model and the actual plant operation is not due to lack of tuning, but due to operational issues such as unattended maintenance requirements or poor process control in the operation. The methodology as described in this paper has been applied at several large mining sites in Chile. The paper presents the characteristics of the proposed methodology, and quantitatively describes its benefits with examples from actual operations.INTRODUCTIONIt probably is fair to say that geometallurgy became widely used in greenfield projects in the Andes region during the mining boom of the 90’s, when massive orebodies were studied and developed, and upfront metallurgical characterisation proved its use for accurate economic evaluation including estimates of plant throughput, energy consumption, final product quality and overall recovery. A few examples of such greenfield studies for concentrator plants in the 90’s are Minera Los Pelambres (Antofagasta Minerals, Chile), Minera Escondida, Laguna Seca (BHP Billiton, Chile), and Rio Blanco (then Montterrico Metals, Peru). Large size hydrometallurgical operations such as Cerro Colorado, Quebrada Blanca and Lomas Bayas (all in Chile), also recognised early on the importance and value of relating ore mineralogy, geological characterisation and metallurgical behaviour."

Jan 1, 2016

By T. Lamb, T. Aston

"The Gays River Mine is located within a complex hydrological regime and underground mining environment. Early in the mine history, the operation was' affected by an inability to control mine water inflows. More recently, the reopened mine operation had been unable to maintain consistent drainage of groundwater to the mine workings and sustain low groundwater levels.In 1992, a series of investigations were completed, which in part Were funded under the Canada-Nova Scotia Mineral Development Agreement. The studies undertaken included: hydrochemical and drainhole well screen assessments, an air photo study of sinkhole features, numerical modelling studies and a major piezometer installation and overburden soil study. The results indicate that the water draining to the underground workings is comprised of two distinct components: precipitation over the drawdown cone catchment area and seepage from the nearby Gays River. In addition, a third ""balance"" component was' also found, which represents uncertainties in the areal extent of the drawdown cone and river seepage components.After outlining the history of the groundwater problems experienced at the Gays River Mine, this paper examines the various studies undertaken during 1991-1992 and concludes that control of groundwater levels in the mine area is achievable. A number of recommendations are also proposed for future study ."

Jan 1, 1993

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size."

Jan 1, 2016

By G. W. Poling, E. M. Coelho

"Sedimentary phosphate ores make up approximately 87% of the world's known reserves and are generally more difficult to beneficiate than igneous ores. In almost all cases, desliming prior to flotation represents the major source of losses. Laboratory studies of selective desliming of sedimentary ores are presented. Some fundamental studies with pure mineral systems are also discussed. Selective desliming, especially using selective flocculation, gave the best performance. Possible industrial applications of this selective flocculation-flotation procedure are discussed.IntroductionPhosphate ores are a major source of raw materials used in inorganic fertilizers (which supply nitrogen, phosphorus and potassium). Approximately 96% of the total world production of phosphate is utilized in the fertilizer industry. Reserves and production data are available in the literature. Today deposits with grades as low as 4% P2O5 are exploited in a few cases. However, in some northern African deposits, ore grades are still as high as 33 - 35% P2O5. Hout pointed out in 1982 that approximately 200 million tonnes of phosphate ore were upgraded by flotation only.Although there is a large number of phosphate minerals (over 300, only those in the apatite series are important ore minerals in phosphate ores. The most common member in this series is fluorapatite – Ca5(PO4)3F. However, in sedimentary phosphate rocks, many different substituents occur in the apatite lattice. Carbonate-fluorapatite (or francolite) is one of the most common names used to describe sedimentary apatites. It can be represented by the empirical formula:"

Jan 1, 1986

By T. ?kre, O. M. Dotterud, S. Haarberg, J. Thonstad, G. M. Haarberg

An electrowinning pilot plant has been constructed at Falconbridge Nikkelverk A/S, Kristiansand, Norway. The equipment consists of a mixing tank where the electrolyte composition and temperature are controlled, an electrowinning tank equipped with five cathodes and six anodes of commercial size and design and a dechlorination facility. Electrowinning experiments were carried out in this pilot plant using acid cobalt chloride solution from the cobalt tankhouse. Key parameters were varied to obtain an improved understanding of the cobalt electrowinning process, focusing on the detrimental deposition of cobalt oxide on dimensionally stable anodes. The extent of anode scaling was found to be dependent on the electrowinning conditions. Low pH, temperature and cobalt concentration resulted in less scale being formed, however at the expense of cobalt current efficiency and cell voltage, adversely affecting electrowinning production capacity and energy consumption. When operating at high acidity, pH in the anolyte was higher than in the catholyte, which is believed to be due to H+ ions taking part in the current transport across the diaphragm, migrating out of the bags surrounding each anode.

Jan 1, 2005

By X. Cao, M. Xiao, M. Jahazi

Magnesium alloys have low hardness, wear, erosion and corrosion resistance. The repair of service-damaged aerospace components made of magnesium alloys is an attractive solution in terms of time and cost saving. The feasibility of applying laser beam technology to repair ZE41A-T5 magnesium alloy sand castings in the machined surface conditions was studied using a continuous wave 4 kW Nd:YAG laser system. The influence of process parameters such as laser power, cladding speed, wire feed rate and defocusing distance on the shape, size and area of single cladding beads is discussed using a process optimization software. Sound single clad beads with good geometric characteristics were obtained using strictly controlled laser process parameters. The overall results indicate that laser surface cladding using filler wire has the potential for repairing aerospace components made of cast magnesium alloys.

Jan 1, 2006

By R. S. Douglas

Introduction The mine at Copper Mountain of the Granby Consolidated Mining, Smelting and Power Company was one of the pioneers in the use of blast-hole diamond drilling for ore breakage. This method of mining has now been brought to a high degree of perfection. The system in use has?been described in a previously published paper which has become an important part of the literature o the blast-hole drilling method. At the time of the establishment of the system at Copper Mountain, standardized loading and drilling procedures were set up. These procedures were based partly on the results of experiment and partly upon the judgment of men experienced in breaking rock in the mine. The success of the method has been proof of their adequacy. With the progress of scoping in the mine, the diamond drill method of breaking was applied to other ore blocks where different conditions obtained. It was found necessary to make adjustments in the standard procedures to get the best results under the new conditions. The following paper attempts to express, in terms of mathematics, the relations of the variable factors. Until recently, estimations of drilling required were based upon the tonnage to be broken and the proposed rate of explosive loading. A revised method of estimating is outlined below which is direct and which involves no unrelated variable factors.

Jan 1, 1947

By Qing-hua Tian, Xue-yi Guo, Fei Li

A novel process for the preparation of a-Al2O3 from secondary aluminum dross was studied. Factors including alkali dross ratio, salt dross ratio, smelting temperature, smelting time, leaching temperature, leaching time, and the solid-liquid ratio, which possibly influence the transfer of Al into water were studied, and the feasibility of using seed precipitation as a treatment technology of the leachate was discussed. The optimum condition of the process was determined as: alkali dross ratio 1.3, salt dross ratio 0.7, smelting temperature 500°C, smelting time 60min, leaching temperature 60°C, leaching time 30min, solid-liquid ratio 1:4. The results show that using the seed precipitation method, the leaching of aluminum reaches 92.71%, demonstrating the technique as a feasible and effective treatment technology of the leachate.

Jan 1, 2011

By A. S. Robb

SAMPLING of an ore-body is one of the fundamentals in its exploration, development, and exploitation. It is carried out to determine the gold value per ton of an ore-shoot and the probable gold output of the refinery. Sampling also places any broken ground in one of two classes, ore or waste. The value and importance of correct sampling has been shown repeatedly in the past. On the other hand, instances could be given where those in charge of mines have not believed in sampling, and the result has been the same in every case-disaster. This has in all probability been due to assuming that good-looking, well-mineralized rock was ore. Sampling in some form might have averted this misfortune. In this essay, only the method of sampling and the estimation of ore reserves is treated. All titles, figures, and values are fictitious. None of the illustrations can be directly applied to any portion of the Hollinger mine, except Figures 1 and 2, which are included with the special permission of the Canadian Mining Journal. METHODS OF SAMPLING Hollinger Consolidated Gold Mines, Limited, has, from the very beginning of operations, carried out an extensive system of sampling, and the results of this sampling have completely governed the whole mining programme. The Hollinger discovery was made in 1909 and prospecting and exploration of 'the surface began at once. Four men were given jobs as samplers and they sampled thoroughly all the outcrops and all bed-rock which could be exposed to view by removing the overburden. When shaft sinking began, samples were taken at two-foot intervals. In 1912, an underground gang of six samplers was organized, and the number was increased at a rate of about two men per year as the size and extent of the workings grew. No permanent record of sampling was kept until 1919, in which year an average of 11.6 men took 28,458 samples, cutting 113,894 feet of sample. From that time until the end of 1934, the average number of samplers varied, but the total number of samples cut, and the total footage sampled, increased.

Jan 1, 1937

By C. Hari Manoj Simha, J. Gholipour, M. J. Worswick

Due to the high pressures involved in the hydroforming process, friction and lubrication play an important role and can affect formability of the material. Tubes of A1Mg3.5Mn aluminum alloy, of 76.2 mm (3 inch) outside diameter and 2-mm thickness were considered in this study. Three kinds of lubricants, Al070, Hydrodraw711 and water, were applied to the tubes and tubes were hydroformed to burst in a square shape die cavity. The key process parameters were recorded during the tests. An in-house Gurson-Tvergaard-Needleman (GTN) damage-based material model, implemented in LS-DYNA, was used to model the process and predict the formability of this material. The applied axial loads and internal pressures recorded during the tests were used in the computations. The effect of different types of elements (solid and shell) with different constitutive models (von Mises and GTN models) in predicting the strain distribution is studied. The GTN damage-based material showed a good ability to capture necking and displacement histories in this process. Both predicted and measured results showed that the lubricant with lower coefficient of friction can effectively increase the comer expansion.

Jan 1, 2006

By Paul M. Lévesque

The Dome Mine has been in production for nearly 100 years and throughout the years many different mining methods were used to extract the ore. An exploration program late in the 1990s outlines new resources requiring the mine to extract the rock and some previously placed backfill (alluvial sand and/or classified tailings). It is therefore imperative to separate the backfill from the rock to reduce the negative impacts of handling the backfill on the ore pass, crushers and mill processes. Separating the backfill from the ore at the source would also reduce and/or eliminate the cost of handling this waste stream. The paper will touch on the backfill removal criteria, the risks, the alternatives and the selected method, screen decks, for backfill removal at the Dome Mine. The 155549 bulk zone case study will illustrate how the screen decks are in use at the mine. The paper will also illustrate how the lessons learned and conclusions of the work done for the 155549 bulk zone were applied to the second screen deck installation for the 257260 bulk zone.

May 1, 2009

Situation Brands & Employment Value Propositions of mining sector firms are perceived negatively Competitive labour market is generally not aware of the diversity of mining careers Jobs requiring unique skills & experiences are no filled Traditional means of generating awareness to attract candidates is not aligned with how youth (for example) uses technology throughout the recruitment process Gobal economic downturn

May 1, 2009

By M. Leijd, K. S. Forrester, M. Saxon, M. Oczlon

This paper provides an introduction to wet high intensity magnetic separation (WHIMS) and its successful application to the beneficiation of rare earth element (REE) enriched eudialyte. The analysis includes an in-depth reporting of the deportment of key elements as well as a statistical interpretation of the relative importance of operational parameters including magnetic field intensity, flow velocity, and matrix loading density. Conclusions are drawn on the relative success of the technology, potential areas for process improvement, and the research direction that continues to be investigated. Three original equipment manufacturer (OEM) technologies were subjected to a series of screening and characterization tests to identify the optimal operating parameter set to magnetically beneficiate eudialyte from Norra Kärr, Sweden. Upon the completion of the characterization test it was apparent that the Metso HGMS technology was superior with respect to REE recovery and gangue rejection for the Norra Kärr composite. The Metso HGMS was then subjected to a series of verification tests to confirm the repeatability and reproducibility of the system.

Jan 1, 2014

By R. J. Grant, D. W. Scott, M. A. Cooper, E. R. Shannon

"The Brunswick No.12 site concentrator processes 10,500 tonnes per day of a complex lead, zinc, copper and silver ore producing four concentrates by differential flotation. Research over the years has led to increased understanding about the mineralogical and flotation characteristics of the ore. A pilot plant study conducted at Lakefield Research, primarily designed to investigate the technical feasibility of semi-autogenous grinding, provided an opportunity to test recent theories about grind size,, reagent schedule and flowsheet configuration.A fundamental approach was taken with each of the unit processes involved in grinding and flotation. Basic operating and metallurgical criteria were established in each area and a step-by-step implementation program initiated in the plant.Significant improvements in metallurgical and financial performance have been realized through the application of basic grinding and flotation principles using conventional milling equipment and without major capital expenditure. Current operating practice is detailed and metallurgical advancements cited.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mines near Bathurst, New Brunswick. Brunswick is a publicly traded company with majority ownership held by Noranda Minerals (63%). In addition to the No. 12 underground mine, the company operates a lead smelter and phosphate fertilizer plant in Belledune, N.B. and maintains a 25% interest in a joint venture with Noranda Minerals' Heath Steele mine near Newcastle, N.B. Through the four operations, a total of 2000 people are directly employed with fixed assets totalling Cdn$187 million (BM&S, 1991)."

Jan 1, 1993

By David Meadows, Elmer Palmer, Steve Dixon

As part of the Goldcorp Inc growth plan Minera Peñasquito SA de CV has developed its polymetallic deposit with a large “state of the art” concentrator to process lead and zinc ores. The plant consists of two grinding lines including 38ft diameter SAG mills and 24ft diameter ball mills. During mid to late 2009 concentrator commissioning activities commenced. First concentrates were produced in October 2009 and now the plant is meeting its design basis of 65,000 mtpd per line. This paper describes the design and operational experience to date for its grinding circuit design, together with the recently commissioned HPGR crushing circuit.

Jan 1, 2012

By R. Phillips, A. G. Doll, D. J. Barratt

"The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less.This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference."

Jan 1, 2012

By Brian Mattie

Overview ?Overview of the mining area ?Description of the mining phases ?Risk assessment ?Design criteria and description for freeze drifts ?Freeze wall design ?Raisebore mining Four Main Phases: 1.Development of freeze drifts on the 520 and 590 levels 2.Freeze drilling and ground freezing to isolate the Zone 4 North ore body from water bearing sandstone. 3.Develop raisebore and extraction chambers including access drifts and ramps under freeze protection. 4.Start raisebore production mining of the Zone 4 North area.

Nov 1, 2011

By F. Gaul, H. R. Manouchehri, A. Mosser

"Mining is a major energy intensive industry that contributes in consuming about 7% of the total world’s energy in which almost half in comminution. The underlying trait that drives energy consumption upwards appears to be somewhat persistent due to increasing in population, demands and growth rate. High grade resources have been/being depleted; consequently, low grade, high competent and complex ores with complicated geological structure are brought into perspective. For efficient extraction of values from such resources comprehensive multistage mining and processing strategies must be taken into account. Different treatment technologies, including ore sorting, must be considered to improve resource efficiency and productivity while taking into account the reduction in energy and water consumptions and related sustainability issues.The implementation of sorting technology in mining industry has a long past and its impacts on improving the overall efficiency of both mining and milling have been proven. However, the lack of complete understanding of its potential combined with ore complexity and low capacity of sorting machines have prevented the large scale application in mining industry. The application of X-Ray transmission sorting at Mittersill Tungsten Mine in Austria is presented and discussed herein. A technoeconomic analysis of the technology has revealed a significant potential of adding value to the concentration process. The rough feasibility study has given a strong feed-back on profitability and short time payback of about 2 years for the investment. Except the economic benefits the technology has positive environmental impacts. The potential for saving energy and water is large. The rough calculations have revealed that the energy saving can be up of 840MWh/annum. Furthermore, the ongoing cooperation between Mittersill mine and the sorting manufacturer is a good example on how the development of more competitive products, and product offerings, can be made."

Jan 1, 2016

By X. Cao, B. S. Naik, D. L. Chen, P. Wanjara

AZ31B-H24 Mg alloy sheets with a thickness of 2 mm were friction stir lap welded (FSLWed) at two tool rotational rates of 1000 and 1500 rpm and two welding speeds of 10 and 20 mm/s. The tensile behavior of the FSLWed AZ31B-H24 Mg alloy was then evaluated at low (-40°C), room (25°C), and high (180°C) temperatures. It was observed that the failure load increased with decreasing tool rotational rate and increasing welding speed. The maximum failure load occurred at a tool rotational speed of 1000 rpm and a welding speed of 20 mm/s at all temperatures tested. It was also noticed that at the high test temperature, the samples failed along the sheet interface, i.e. shear fracture. At the low and room temperatures, the samples failed on the advancing side (AS) of the top sheet near the interface between thermo-mechanically affected zone (TMAZ) and stir zone (SZ). The different modes of fracture observed are associated with the hooking defect.

Jan 1, 2014

By Gary Watters

PORTS AND ARCTIC CONDITIONS ?Large ice forces ?Standard designs fail in the arctic ?Specialized construction methods for ice PRESENTATION OUTLINE 4 Example Projects ? 2 Alternative Construction Methods ? Advantages & Disadvantages ?Controlling costs

Oct 1, 2010