Search Documents

Superconductivity, New Mexico and Mining? ? High Temperature Superconducting cables made from ?nickel tape? ? Testing on U.S. power grid ? 25 year time horizon Purpose Create awareness about the successful application of energy management systems at a Northern Ontario mine site.

May 1, 2008

By J. Spross

"The Key Lake mill has operated since the fall of 1983. The ore from both Key Lake open pits will be depleted by 1997. It is planned to use this mill, located about 60 km southwest of McArthur, to process the McArthur River ore.While the geological data collected so far on the McArthur deposit are encouraging, more information of the deposit is needed before any detailed mine planning can begin.The surface drilling program identified the orebody and provided information on the geomechanical and hydrological properties of the overlying sandstone. It was proposed to conduct an underground exploration program to further delineate the orebody. This was air proved following a public hearing and review process. This program involves the sinking of a 630 metre deep shaft and the driving of one or two drifts along a portion of the orebody. From these drifts, exploration drilling every 10 m to 15 m through the orebody will provide the information required for the preparation of a feasibility study and an Environmental Impact Statement (EIS)."

Jan 1, 1994

By Chuck Crowell

ISO Standards ?Provide Information to Address Commercial and Safety Needs for Standardization: ?Definitions and Terminology ?Test Methods ?Performance Criteria ?Conformity Assessment Process ?Developed by Global Experts ?Promote Global Harmonization

May 1, 2013

By C. L. Reichardt

Pressure exerted on gold producers by regulators, project financiers and civil society in the wake of the Baia Mare tailings spill in Romania during 2000 prompted most responsible gold companies to sign up to the International Cyanide Management Code for the Manufacture, Transport and Use of Cyanide in the Production of Gold (the Code). The Code stipulates a ?cradle to grave? approach more comprehensive than that applied to any other mining reagent and poses particular challenges for operators who use cyanide-bearing tailings for backfill. This paper examine some of the challenges for Code compliance facing deep underground gold mines that employ backfill technology, most particularly the requirement to demonstrate that the potential migration of cyanide (and its degradation products) from emplaced backfill will not have an unacceptable impact on worker health and safety or the receiving environment, either during mine life or after closure. Although the Code only contains a single reference to backfill, more careful consideration confirms that most sections of the Code that deal with tailings management are potentially applicable to mines where tailings material is used for backfill, as are certain principles pertaining to aspects of operations, worker safety, emergency response, training and dialogue with stakeholders. For gold mines of the Far West Rand, the most significant cyanide-related risks associated with backfill operations relate to worker exposure to cyanide-bearing seepage and HCN gas. There is potential for seepage of cyanide-bearing water from backfill to compromise the beneficial use of surface and groundwater, and thus impact on downstream users and ecosystems. However, the extreme depth of mining and the specific geological and hydrological controls on the Far West Rand suggest that the potential environmental risks associated with backfill are likely to be considerably less significant than the cyanide-related risks to the workforce.

May 1, 2007

By N. Morrison, E. J. Rogans, A. J. Macintosh, N. Schoeman

"The design of carbon-in-pulp (CIP), and carbon-in-leach (CIL) adsorption circuits has essentially remained unchanged since the early days of the carbon process for gold recovery. For CIP circuit the pulp residence time is traditionally fixed at one hour per contactor with a carbon concentration of between 15 and 20 grams per litre, and the counter current carbon transfer rates are in the region of 15% pulp recycle. For CIL, the pulp residence time is usually three hours per contact or, with lower carbon concentrations ( 5 to 10 grams per litre).The drawbacks of using the counter current CIP/CIL adsorption circuits are discussed using modeling developed for CIP/CIL plant design. Counter current CIP/CIL, circuits are then compared with the carousel method of adsorption circuit design.The use of equipment suitable for the carousel approach is discussed which is, the AAC cylindrical and pumping (MPS) screens, the AAC pump-cell plant and launder designs.Finally, two plants at the Vaal Reefs Gold Mining and Exploration Company that use carousel adsorption circuits, namely the Vaal Reefs No. 1 Gold Plant, a CIL plant with stepped contactors, and the Vaal Reefs No. 2 Gold Plant, a CIP using a very short residence time (AAC pump-cell) are discussed."

Jan 1, 1998

By Marek Mika

This Paper has been prepared to be presented at the 23rd World Mining Congress & Expo ? Montreal 2013. It presents the idea how to carry out the shaft sinking operation, going through highly water-bearing and very weak rock strata, giving as an example one specific shaft sinking project which is being executed for one of the Polish collieries by our Shaft Sinking Company Content 1. Introduction. 2. Hydrogeological conditions within the area of the shaft. 2.1. Hydrogeological conditions assumed at the stage of designing. 2.2. Hydrogeological conditions encountered in the course of sinking. 3. Designed shaft lining. 4. Procedures for the shaft sinking. 4.1. Designed procedures of the shaft sinking. 4.2. Procedures for preservation and strengthening of the shaft lining and the surrounding rock strata. 5. Technological guidelines for proceeding with the shaft sinking ? selection of special methods. 6. Options for mechanization of work for the selected method. 7. Conclusions.

Aug 1, 2013

By A. Sargeant

This paper evaluates the application of post consumer glass as a cementing agent in underground mine backfills. The underlying theory indicates that glass is pozzolanic and, when used in a finely divided form, behaves as an activator to generate binding products, thus contributing to the development of backfill strength. The objective of this study was to evaluate the strength performance of backfills when Normal Portland Cement is replaced with various percentages of post consumer glass. The study evaluated the performance of backfills prepared using tailings from three mines. Each backfill was prepared using unique recipes, and were evaluated at cure times of 7, 14, 28, 56, 112 and 224 days. Laboratory work involved visual, physical and chemical material characterization followed by strength evaluations. Results of strength assessment revealed that backfill prepared with glass is reactive and can contribute to the strength of backfill. The results also indicated that the reactivity of glass may be affected by the incorporation of slag within the recipe, the availability of lime and the level of hydration of the binders. The study concluded that, at 15 % glass replacement of NPC, backfill prepared with mine tailings, NPC and glass can achieve improved or equivalent strength performance compared to backfill prepared tailings and NPC alone.

May 1, 2007

By J. E. Danoczi, J. A. Herbst

"Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne (FalC) area in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as gently as possible so as not to damage the diamonds.Autogenous grinding mills (AG mills) use a combination of impact crushing, abrasion and attrition to break up the kimberlite. The forces that occur during the actions of abrasion and attrition cause the kimberlites to break up preferentially along lines of weaknesses which offers a “diamond friendly” method of comminution.Hard competent kimberlite is commonly found in the diatreme zone as well as the root zone of the volcanic pipe and is the source of kimberlite for most of the Southern African diamond mines. Softer kimberlite is typically found in and around the crater area of a volcanic pipe and it is this kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills. In order for Shore to benefit from the softer kimberlite found in the Star - Orion South diamond project, two large (10.97 m diameter x 7.10 m long) AG mills were designed for the comminution section based on extensive test work and simulations by Metso Minerals (Metso)."

Jan 1, 2012

By W. Almdal

"To compete in the ever expanding global market, companies must continuously improve. Benchmarking, a tool that can help determine where the best areas for improvement are, is more than comparing measures, it is comparing how business is carried out and how decisions are made. The key to success is in integrating benchmarking results into the organization, so that those most affected by the results own them and are empowered to use them as a positive change agent. This is a necessary step to achieving substantive change to practices and achieving optimum performance improvement. IntroductionBenchmarking is a powerful tool that can assist in the continuous goal of improvement. Benchmarking is more than comparing productivity rates or unit costs, it is seeking out best practices and assimilating them into a business to provide a positive change agent.Benchmarking is a continuous process - is time consuming, labour intensive, and requires a lot of discipline. There are no easy answers and no easy solutions, just a lot of work. The results, however, are nothing short of spectacular. More and more companies are adopting benchmarking practices because it is a key tool of the learning organization and will become part of the way business is done, part of the way it is managed. Business must change to stay ahead or to get ahead and benchmarking can accelerate the process of business change. Improvements in an organization can happen faster and more effectively with a benchmarking approach."

Jan 1, 1994

By C. B. Webber, L. S. Diaz

"The paper presents the approach taken by Craigmont Mines to grinding circuit control. A detailed description is given of a fully automatic control system which bases its control actions on the continuous measurement of particle size in the cyclone overflow stream. The control system holds a specified particle size in the cyclone overflow, and grinds rod mi 11 ore feed at increased rates. The principles of operation of the system used for continuous measurement of particle size are described, end the improvements in mill throughput and copper recovery over several months of continuous operation are presented.INTRODUCTION Craigmont Mines Limited is located in the south-western interior region of the province of British Columbia, approximately 230 road miles north-east of Vancouver, and ten miles west of the town of Merritt. A moderate climate, good roads and service facilities provided by the Canadian Pacific Railway, Inland Natural Gas Company, and the B.C. Hydro and Power Authority, have provided a very favorable mine and plant site.The preliminary metallurgical design of the Craigmont mill was based on the test results of samples obtained from the original 2500' level drift during 1959. Pilot plant runs and other research testing for design pur¬poses were conducted at the Canadian Exploration Ltd. Laboratory, at Salmo, B.C. The design flowsheet was altered in progressive stages from 2,000 to 3,000, and finally 4,000 tons per day as the ore reserves became better defined. Construction work on the 2,400' level mill site commenced in late 1960. The official opening of Craigntnt Mines Limited took place on September 15, 1961, a little over two years from the time of the metallurgical assessment of the original ore samples.Mill throughput to date has varied widely both on a daily and a monthly basis, due to the varying hardness of the mine ores. The grindability af the ore appears to be related to the oxide iron content, which varies from lows of 9% to highs of 20%. Daily tonnage has ranged from 5,000 tons per day with 10% iron in the feed, to 6,000 tons per day with 20% iron feeds."

Jan 1, 1973

By C. Matthews, A. Vo

Australia is one of the world’s leading exporters of bulk commodities and the extensive use of sampling equipment is key to the successful management of each mining operation. At the process plant, without a full understanding of the feed, product and tails, it is impossible to fully optimise the performance of the plant, such that the metallurgical balance is often open to error. At the port, a statistically correct, bias free and compliant sampling system is crucial to ensuring exported minerals are reflective of their true value and to avoid penalties. Over the last decade, as a result of the iron ore boom, there has been high demand for reliable, representative and standard compliant solids sample systems in Australia. This paper reviews several solids sampling applications at Australian mine sites, the challenges and experience gained and how the implementation of reliable representative sampling systems has provided better understanding of plant process performance, improved plant control and overall benefits to the operations. INTRODUCTION Mining is the primary contributor to the Australian economy with Australia ranking in the top 4 in economic resources for 21 primary industrial minerals in 2016 (Britt, et al., 2017). Australia is one of the world leaders in the export of the majority of its commodities including gold, copper and iron ore (Britt, et al., 2017). Therefore, a suitable and standard compliant sampling system is essential for evaluating plant performance and content verification. At the mine and at the port, the larger iron ore miners in Australia have developed stockpile models to predict the grade of their ore down to individual blocks of the stockpile. This allows the miner to create the right blend of material for sale to their customers and ensures they are not underselling their product or at risk of penalties for impurities or low grade. As an example, the average difference between the benchmark 62% Fe and low grade 58% Fe fines at the time of this report averaged US $20/tonne according to the Metal Bulletin Iron Ore Index (Fastmarkets MB, 2019). At a shipload of 180kt this would be a variation of US $3.6M. Whilst this is an extreme example, it highlights the economic importance of producing the correct grade product and a recognised representative sample of said product.

Jan 1, 2019

By Janne Karonen, Stephen Hughes, Mikael Jåfs, Jan Stål, Hannu Johto

End-of-life electrical and electronic scrap material attracts attention as a good opportunity for new value creation through efficient metal and energy recovery of such materials. On the other hand, the treatment of such wastes becomes important to avoid problems for society and environment. Treatment of such secondary raw materials faces multiple challenges due to their increasing complexity and evolving nature. Processing of these complex scrap materials together with recovery of a wide range of valuable metals with a combination of pyrometallurgy and hydrometallurgy using Outotec technology is discussed in this paper. One key consideration is environmental performance which needs attention when processing such complex secondary E-waste materials. Outotec has successful experience with commercial projects in the countries at the forefront of environmental and operational standards. INTRODUCTION Increasing attention has been drawn to the responsible processing of end of life Waste Electrical and Electronic Equipment (WEEE) as part of metals recycling, especially copper. It has been estimated that the amount of WEEE globally in 2016 was around the level of 46 Mtpa (Balde et al., 2017), representing a major disposal challenge but at the same time huge opportunity for resource recovery. The potential for increasing the recovery is high, because the official recycling rate of WEEE is in 2016 only 20% (Balde et al., 2017) and at the same time the estimated increase of the WEEE amount is between 3 and 5% per annum in the EU (Eurostat, 2019).

Jan 1, 2019

By Ros Taplin

Realizing the potential of cutting greenhouse gases (GHGs) associated with mining, a variety of approaches has been proposed for their mitigation. The Clean Development Mechanism (CDM) under the Kyoto Protocol to the UN Framework Convention on Climate Change (UNFCCC) has been a key mechanism to assist in implementation of mitigation measures. The objectives of CDM are not only to assist Annex I countries in meeting their GHG emissions reduction targets with cost-effective reduction but also to achieve sustainable development in non-Annex I countries. However, apart from China, India, Brazil and Mexico, many developing countries are still in the stages of formulation or realizing CDM strategies. Projects associated with methane capture and flaring are the fourth most prevalent type of CDM project internationally. This research primarily has addressed emissions abatement and sustainable development aims and effectiveness of registered CDM projects associated with coal mining in China. The paper reviews 30 currently registered CDM projects in China on the UNFCCC database and six other non- Chinese projects. Systematic evaluation involving content analysis of documentary evidence regarding coal mining CDM projects is presented in relation to firstly, quantitative reduction of GHG emissions and secondly, sustainable development outcomes. The projects have been assessed via a set sustainability criteria. Overall it was found that sustainable development goals are only briefly referred to in Project Design Documents, Letter of Approvals and validation documents. Varying types of sustainability initiatives have been implemented with weak to strong indications of effectiveness. This has implications for the future effectiveness of CDM projects in the mining sector, the proposed new market mechanism under UNFCCC, and for assessment of projects under mechanisms established outside the UNFCCC.

Aug 1, 2013

By A. Atrafi, L. Barroilhet

The top size of particles in the flotation of potash ores, which can be as large as 4 mm, exceeds by far the top size in other flotation plants. It is then understandable that while long chain amines are used in the flotation of fine fractions (below 0.8 mm) of potash ores the coarse particle flotation also requires an extender oil. While new and very promising fluidized-bed flotation machines (e.g. HydroFloat) constitute a significant development in the flotation of coarse particles, in the area of extender oils, as reviewed in 2007 by Strathdee, Gotts and McEachern, there have been no new developments to replace the industry standard asphaltene-based carcinogenic extenders. This situation first of all results from the experimental problems that arise when water-soluble minerals like sylvite are to be tested in saturated brine. Both oils and longchain amines are water/brine insoluble. The oil with the amine dissolved in it can however be emulsified and then used as an extender oil. Such oil droplets must wet KCl particles and the emulsion must be stable to avoid handling problems. In this paper we test the use of the phase inversion technique as a method of studying wettability of KCl particles by the oil in saturated brine, and the effect of amine dissolved in this oil on the wettability. The results show that this relatively simple technique can be used to characterize the wettability of fine KCl particles by the tested oil and to determine the effect of added amine on it, and so it can be useful in selecting proper extender oils.

Jan 1, 2016

By Yue hua Hu, Wei Sun, Pan Chen, Li Wang, Runqing Liu, Central South University

"The flotation separation of muscovite from quartz was investigated using mixed sodium oleate/dodecylamine (NaOL/DDA) collectors. The flotation experiments were conducted on single minerals and their collecting performances were studied by means of adsorption amounts and molecular dynamics simulation. Flotation results show that muscovite presents good floatability while quartz exhibits poor floatability in alkaline condition. Adsorption amounts show that both NaOL and DDA can absorb onto surfaces of muscovite and quartz in presence of mixed surfactants. Molecular dynamics simulation indicates that DDA plays an important role in the adsorption of mixed surfactants on these two mineral surfaces. The molecules of mixed NaOL/DDA are arranged in a rigid and well-ordered packing on muscovite (001) surface. Only a few DDA adsorb on quartz directly, and rest DDA and NaOL molecule exist near by the quartz surface, forming a hydrophilic cylinder-like structure. This study may provide guidance for the flotation mechanism and application of mixed anionic/cationic collectors.INTRODUCTIONIn the past decades, there has been an ever-increasing demand for muscovite (KAl2(Si3Al)O10(OH)2) because of its potential applications in cosmetics, construction and metallurgy industries (Barlow & Manning, 1999). Besides, muscovite is an important carrier for some rare metals, including vanadium, titanium and lithium (SsuerrN, 1979). Quartz (SiO2) occurs as the main gangue mineral in muscovite ores, which results in a low purity of muscovite and limits its wide applications. Therefore, there is an urgent need for the beneficiation of low grade muscovite ores. Many studies remove quartz by screening and gravity separation in virtue of their differences in shape, hardness and density. However, these methods undergo poor efficiency in case of small particle size (below 50µm) of muscovite and quartz (Liubakka, Sullivan, Lamphere, Corradi, & Dykhuis, 2011; Santos, Franca, & Ogasawara, 2011)."

Jan 1, 2016

By J. P. Rajot, H. Mouzannar, M. Bost

"The design of rock foundations may need to evaluate shear strength of rock-concrete interface by performing laboratory direct shear tests. A series of tests were carried out on specimens for different values of the spacing free of encapsulating material about the shear plane and different values of normal stress. Different kinds of failure were observed and not necessarily at the rock-concrete interface. The spacing free of encapsulating material appeared to be of significant influence on the test results. A mechanical analysis is presented which illustrate the influence of the loading conditions in the direct shear box on the failure mechanism. INTRODUCTIONThe design of rock foundations subjected to significant lateral loads requires defining the value of the shear strength of the interface between rock and cast in place concrete. Verifying the stability against sliding of strip footings subjected to inclined loads (SETRA, 2009) or concrete gravity dams (CFBR, 2013) are common examples where design modelling approaches imply the shear strength, sometimes the deformation behavior, of the rock-concrete interface, more or less assumed as a failure plane.Defining the behavior of rock-concrete interfaces relates to tribology. Many studies have been conducted to improve the representation of this behavior (e.g., Johnston & Lam, 1989; Kodikara & Johnston, 1994; Gu, Seidel & Haberfield, 2003; Saiang, Malmgren & Nordlund , 2005; Fishman, 2008; Eltervaag, 2013; Gutierrez, 2013), raising many questions. The behavior appeared to be influenced by many factors such as the geometry of the interface which is not planar, the roughness of the natural rock, the rock mineralogy and the concrete formulation. In addition, the study of the shear strength of rock-concrete interfaces involves considering the two different deformation behaviors of both rock and concrete. Finally, the observed failure mechanism is strongly influenced by the initial cohesion due to adhesion between the two materials when concrete is directly cast onto rock."

Jan 1, 2015

By Pierre Beaudoin, Michel Bourassa, Robert Lanthier, Samir Chéfaï

"Mine Doyon, in collaboration with CRM's Process Control Division, improved the control strategy at the SAG mill I Ball mill grinding circuit. The project aimed at increasing operation stability and throughput. First, a needs analysis was achieved in order to define the control philosophy and to upgrade the process control equipments and instrumentation. The stabilizing control strategy has been developed and implemented successfully using single loop PID controllers. The monitoring feature as well as the rule based supervisory control strategy were implemented on 486PCs running Process Vision and COMDALE/C softwares. Main features of the control strategy are described in this paper while results are presented and discussed.RésuméLa Mine Doyon, en collaboration avec le service de contrôle des procédés du CRM, a optimisé la stratégie de contrôle au circuit de broyage. Les objectifs du projet étaient !'amélioration de la stabilité de !'ensemble de !'opération et la maximisation du tonnage usiné. Une analyse de besoins a été réalisée pour concevoir la philosophie de contrôle et déterminer les ajouts a apporter a I 'instrumentation et au systeme de contrôle. Une stratégie de contrôle à deux niveaux, integrant stabilisation et supervision, a été developpee et mise en opération. La regulation est réalisee par une combinaison de contrôleurs Moore de type PID. Le monitoring et la stratégie de contrôle a base de règles soot implantés sur des micro-ordinateurs de type PC/486 avec les logiciels ProcessVision et Comdale/C. Les principaux aspects de Ia stratégie de contrôle sont décrits dans cet article et les résultats obtenus soot présentés et discutés."

Jan 1, 1995

By E. E. N. Smith

"Uranium exploration by Eldorado prospectors north of Lake Athabasca began in late 1944 and resulted in initial discoveries in 1946 in the Beaverlodge region with mill production starting in early 1953. The operation was closed in mid-1982 having produced 21,457,947 kilograms U30 8 from the Eldorado FayVerna mine, Eldorado satellite operations and from other district producers on a custom basis.The Fay- Verna mine consists of pitchblende-brannerite orebodies spatially associated with both sides of a regional eastwest structure, the St. Louis Fault. The orebodies in the footwall (Fay) are elongate deposits of two types raking steeply to the southwest along the 50 degree south dip of the fault.One type consists of networks of fractures and veins filled with pitchblende, calcite and quartz in chlorite, epidote-altered mylonitized mica schists and amphibolites of the Middle Aphebian Tazin Group. The other type is comprised of fragments of mylonitized metasomatic quartz-feldspar granite of Late Middle Aphebian age cemented with a matrix of pitchblende, brannerite, calcite and some quartz. The vein networks lie en echelon in the footwall of the breccia ore bodies which, in part, are capped by the mud gouge of the St. Louis Fault; in other places, the breccia orebodies are overlain by basal conglomerates, grits and arkoses of the late Aphebian Martin Formation which itself immediately underlies the plane of the fault.Orebodies in the hanging wall (Verna) are a series of irregular, tabular deposits lying within a tightly overturned syncline of Tazin mica schists, amphibolites and siliceous mylonites. They consist of pitchblende, calcite-filled fractures grouped into zones and deposits displaying stratabound habits within individual rock types.Also described are several Eldorado satellite properties which were significant producers of uranium and which display complementary geology to that in the Fay- Verna mine.In general, uranium deposits in the Eldorado Beaverlodge region are closely related to minor structures associated with major faults. Uranium appears to be best concentrated where the rocks are well mylonitized and brecciated. Pitchblende fills networks of veins and fractures in metasediments and metavolcanics as well as matrix material cementing brecciated, mylonitized granite. All deposits in the Beaverlodge region lie in close proximity to the unconformity between the Martin Formation and the underlying Tazin Group."

Jan 1, 1986

By R. del Villar, A. R. Laplante

"This article presents four grinding simulation programs, written in Applesoft BASIC. The firs t two calculate residence time distributions (RT Ds) for open and closed loops mills. The third program calculates the select ion functions from the RTD, breakage function and particle size distribution (PSD) o f the feed and discharge. Two linear regression programs are also included to calculate the breakage function. These results are used in the fourth program to simulate continuous or batch grinding kinetics.The modelling approach presented is the size discrete, time continuous matrix formulation presented by Reid (1965) from concepts originally proposed by Epstein (1948). It is at the present time the most widely accepted phenomenological model of grinding kinetics and is standard textbook material (Austin et 01., 1982; Kelly and Spottiswood, 1982, p. 152). The concepts of RTDs and tracer testing originated from chemical engineering theory and practice, and are well presented in Leven spiel (2n d Ed . 1972 , Ch. 9) .Applesoft* was chosen because it is compatible with many micro computers. It is also one of the simplest and least powerful BASIC versions. Thus it can easily be adapted to other more complex BASIC versions.Open Loop Residence Time Distributions (Program RTDOPEN)As mixing, channelling, stagnation and short-circuiting all affect slurry motion in tumbling mills, transport characteristics are very complex an d cannot be derived from fundamental principles. Fortunately , as grinding follows first order kinetics, transport characteristics for the purpose of grinding simulation ca n be represented by the RTD of the slurry phase . It is normally determined using liquid tracers, as it has been demonstrated and is commonly accepted that in industrial ball mill s, the RTD of the so lid phase is particle size independent and equal to that of the liquid phase."

Jan 1, 1985

By R. Browner, J. Collard, D. Ibana

The extraction of cobalt from synthetic pressure acid leach solutions of nickel laterite ores by the direct solvent extraction route using ESPLIM is reported. It first explored the use of gaseous ammonia as pH modifier and then the variables that affect the dispersion of the aqueous phase in the organic phase such as ionic strength, viscosity of the phases, initial droplet size, etc. were explored so that phase hold-up and thus extraction can be effectively controlled. The results show that the technique allows better control of phase dispersion circumventing one of the main weaknesses of conventional solvent extraction.

Jan 1, 2005