Search Documents

By B. Vorobyov

A Canadian company, Sight Power Inc., has developed a revolutionary, fully automated shaft monitoring and inspection system for deep-level mining based on a 3D mobile laser scanning technology. It consists of a special hardware unit and proprietary software with Artificial Intelligence elements for object recognition, features identification and change detection. The main purpose of this system is to significantly improve the safety of underground mining as well as to increase the available hoisting time thus generating substantial additional revenue for the mine.

Aug 1, 2013

By G. P. Holmes

"Bell Copper is situated (Latitude 55°0''N, Longitude 126°14W) on Newman Peninsula on the east side of Babine Lake at an altitude of 2,450 feet above sea level. The mine site is approximately 170 miles north west of Prince George and 40 miles east of Smithers. Access to the property is by way of 30 miles of paved road to the Village of Granisle on the west shore of Babine Lake and then a further 9 miles of unpaved road to Bell Copper's west dock. The two mile lake crossing is made using a tug and barge. A compressed air bubbler system maintains an ice free channel for the barge during the winter months.Temperatures range from summer maximums of around 32 °C to winter minimums in the region of minus 40°C. Long periods in winter may be spent with temperatures in the range of minus 15""C to minus 28°C. Freezing temperatures usually start in October and last for six months. The lake normally freezes over in mid December and the ice breaks up in mid May. Snow accounts for approximately two t11irds of the annual precipitation of twenty-one inches."

Jan 1, 1976

By R. Maxwell

"At Opemiska Copper Mines we have, over the past four years, operated 300 cu. ft. and 700 cu. ft. flotation cells as roughers, scavengers and cleaners and found them competitive with conventional flotation cells on a cu. ft. basis on all phases of flotation.The economics are very much in favour of the large cells for the following reasons:Power consumption is 35 to 40%, of conventional machinesMaintenance cost is about 20 to 25% of conventional machinesSpace required is about 30 to 35% of conventional machinesInstallect cost is about 40%, of conventional machinesTo put the above in more concrete terms below is what we are doing at Opemiska:1. Increasing mill capacity from 2000 to 3000 T.P.D. and will use only 5Cff, of the flotation space for 3000 tons that we used for 2000 T.P.D. with conventional flotation machines.2. Will require only 10 flotation cells for 3000 tons against 85 conventional cells for 2000 tons.3. Cells will be, one 2000 cu. ft. rougher, six 700 cu. ft. scavengers (2 banks of 3 each) and one cleaning circuit using three 300 cu. ft. cells.You will note that in this 3000 ton per day plant, we are going to have only ten cells. Had we put in conventional cells for this tonnage, we would have needed 120 cells."

Jan 1, 1970

By Edmond Chow

Shovel bucket blast fragmentation analysis is an alternate way to assess blast performance and its effects on downstream mining processes. A camera is installed on the boom of cable shovels, and the stick of hydraulic shovels. Images are captured automatically as the shovel digs, and are processed to acquire rock size information. The automatic data acquisition makes this method safe to use with minimal manual labour. It also allows for a large set of sample data to be captured from both the surface and the interior of a bench face. The system has been deployed in several mines to provide an objective assessment of blasting performance. Images are captured from their cable or hydraulic shovels. The images are grouped into sets based on the shovel location and time to match the fragmentation to specific blasts. Blast fragmentation reports are created for each blast after reviewing the results. Measuring blast fragmentation from the shovel bucket proves to be an effective alternative for blast performance assessment with unique advantages. The blast fragmentation information has been valuable to the mines, and the mines have begun adopting it into their operations.

May 1, 2011

By D. T. Smith, S. J. Strohmayr

Originally developed as a step change in ultrafine grinding efficiency, the IsaMill™ has made inroads into conventional ball mill and tower mill mainstream grinding duties during the last 5 years - beginning with the Anglo Platinum mainstream grinding projects in South Africa. At the 2006 SAG Conference, plant testwork on the incorporation of IsaMill™ technology into the McArthur River (Northern Territory, Australia) Pb/Zn primary grinding circuit was reported. The IsaMill™ has now become an integral component of that circuit, treating up to 1mm top size feed and directly producing P80 45 µm rougher flotation feed. Two 1.1 MW IsaMills™ are now used in this duty contributing to a 27% increase in overall plant throughput and a reduction in rougher feed size distribution. In this paper, we report on the current state of development and performance of the IsaMill™ in the primary grinding duty at McArthur River and also consider future directions.

Jan 1, 2012

The original JKMRC AG/SAG mill model was developed over 30 years ago and has been upgraded a number of times since then, with the current published version being the Variable Rates model that is now over 15 years old. Since this model was developed further enhancements have been derived, some of which are applied in-house and some which have yet to be incorporated. The published and the commercially available model in JKSimMet is currently undergoing a comprehensive overhaul with a vastly extended data base for model evolution and validation. Improvements developed within the AMIRA P9 project, in-house development and a number of collaborative projects, are being incorporated into the upgraded model structure. Enhanced capabilities will include: power-based breakage rates scaling; a far wider mill filling range (from 10% to 40%) that exhibits peak in throughput as mill filling increases; higher ball loads; improved pebble discharge function; improved slurry discharge function incorporating important mill design and operational influences; and the new size dependent breakage function. The model will also be able to accommodate some influence of liner design and multi-component ores (blends of hard and soft components). This upgrade is still a work in progress but substantial changes have been made to date. This paper presents some of the new improvements and their influence on the predictive capability of the model.

Jan 1, 2012

By Lo-Sun Jen

Introduction ? Canada is one of the largest miners and explorers in the world and is a world leader in the production and export of many key mineral commodities ? Canada has a stable political regime and a competitive investment and business climate ? Canada is endowed with mineral resources, advanced technology and management know-how ? Canadian stock exchanges are the world?s leading centres for raising equity financing for exploration and mining projects anywhere on the globe As with some other countries, Canada has experienced a recent decline in major mining developments

May 1, 2002

By T. Macpherson

ABSTRACT: Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009

By Peter A. Witt

Highland Valley Copper is a conventional truck-shovel mining and flotation concentrator operation located some 75 kilometres southwest of Kamloops, B.C. (Figure 1). The ore is within a porphyry deposit and is mined at a rate of 135,000 metric tonnes per day from two separate open pits. The nearby mill produces concentrates containing 375 million pounds of copper and 5 million pounds of molybdenum metal yearly. Head grades are roughly 0.40% Cu at a 0.23% Cu equivalent cut-off. The strip ratio currently sits at 0.55:1 with waste quantities made up of separate rock and unconsolidated overburden units. From the mill, concentrates are trucked to nearby Ashcroft and then hauled by rail to ocean port facilities in Vancouver. The mine employs 950 persons and is planned to operate until 2009. The operation is a partnership between three owners: TeckCominco (61.4%), BHP Billiton (33.6%), and Highmont Mining (5%). Management is shared by the two principal owners and directed by an appointed committee.

May 1, 2002

By R. Binning

"Economic high density mineral reclamation and subsequent transportation of solids through a pipeline presents many formidable engineering problems.Mineral reclamation system design by theoretical formulas is almost impossible because solids composition, ie. concentration, velocity, moisture content, solid size, etc. can only be controlled within a broad pumping range.Traditionally this has restricted pumping to relatively dilute slurries whereas it is usually preferred, because of economic considerations to reclaim as high a concentration as possible.At Toyo/De-Velde Corp. we recognized these pumping limitations and began to develop and manufacture a range of standard and auxiliary equipment that would exceed these technical restrictions.MATERIAL RECLAMATION & PIPELINE INJECTIONTo minimize fluid usage and increase material reclamation efficiency we designed a submersible dredge mixing pump that uses most of its energy to pick up material from rest, mix it with fluid into a highly concentrated slurry then push it firmly into a pipeline.Where material is too compacted to be mined by the standard submersible mixer pump, auxiliary high torque self contained submersible excavators can be fitted around the periphery of the mixer pump. This is to facilitate excavation and break up of the compacted material into a slurry.High flexibility of this system can be achieved by combining the many equipment variations available into the most efficient format to fit individual site requirements.Whatever combination of equipment is selected, torque is nullified by counter rotating excavators against each other. This increases effective excavator/material bite torque but also allows mixer/excavator rig suspension by cable for deep water material recovery."

Jan 1, 1985

IBI Alliances ? Government ? People ? Academic ? Associations ? Media ? Customers ? Agencies ? Shareholders ? Industry consultants ? Investment Authority ? Geological Survey ? Department of Mines ? People ? Local Residents ? Mineworkers ? Academic ? University of Guelph ? Uganda Vermiculite Institute ? Associations ? TVA ? Organic Certification ? Media ? Canada ? International ? Customers ? Advocacy role ? Agencies ? Regional International

May 1, 2006

By X. Wu, W. R. Chen, J-G. Legoux, B. R. Marple, E. Irissou

Cold gas dynamic spray (CGDS) has been considered a potential technique to produce the metallic bond coat for TBC applications, because of its fast deposition rate and low deposition temperature. This paper presents the influence of spray processes for bond coat, including air plasma spray, high velocity oxy-fuel, and in particular CGDS, on the oxidation performance of TBCs with a Co-32Ni-21Cr- 8Al-0.5Y (wt.%) bond coat. Oxidation behaviour of the TBCs was evaluated by examining the coating microstructural evolution, TGO growth behaviour, and crack propagation during thermal exposure at 1050°C. The relationship between the TGO growth and crack propagation will be discussed.

Jan 1, 2010

By L. Xia, B. Hart, K. Douglas

In the flotation of Rare Earth Element (REE) bearing minerals, oxalic acid is reportedly acting both as a depressant and pH modifier. Testing has established the significance of oxalic acid in the flotation process however its specific role in either the recovery or selectivity of REE over their gangue minerals is not well understood. Pulp pH reduction trials with alternative acids have not shown the same effect on the REE mineral recovery or the depression of gangue phases. This work examines the effect of oxalic acid on the surface of gangue minerals (quartz and carbonates (dolomite and calcite)) in a series of conditioning tests. Gangue surface analyses by TOF-SIMS indicate that oxalic acid inhibits the transfer of secondary ions generated during the conditioning process from one mineral phase to another. In this regard, the oxalate anion acts to fix ions in solution through chelation, limiting their participation in surface adsorption.

Jan 1, 2014

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationships in fact discernable.

Jan 1, 2011

By Bruce C. Smart

"Very little attention was given to the regulation of uranium mills by the Atomic Energy Control Board prior to 1974. The ore grade treated by Canadian mills in the past was in the order of 0.08 - 0.3% U and it was not difficult to keep the exposure of workers well below regulatory limits. Furthermore, uranium milling has also been substantially free of occupational illness because environmental control has been generally satisfactory (l).The discovery of higher grade ore bodies in Canada has resulted in higher radiation levels in one mill and this has partly contributed to a need for increased radiation monitoring in the mill. In addition, as greater insight is gained on the effects of radiation, the implementation of the ALARA principle is being stressed at all mills.The concept of ALARA was emphasized by the ICRP (International Committee for Radiological Protection) in 1977 and stands for '""as low as reasonably achievable'"". It is based on the premise that no proven threshold for potential effects of radiation exists and that the actual individual exposure should therefore be kept as far below the regulatory limit as possible, economic and social factors being taken into account."

Jan 1, 1982

By T. R. Bieler

"Hot forming and superplasticity in powder metallurgy aluminum alloys and composites is reviewed. The effects of alloy composition, particulate composition, size, and size distribution is summarized. The role of climb distance for recovery is described in connection with the size of strengthening phases. In materials with fine strengthening phases on the order of one micron or less, high strain rate superplastic deformation processes are likely. However, the quality of superplastic deformation depends on the prior processing history, and these effects are reviewed. Very few data describing the effects of hot forming history on post-forming properties exist, but some results emerging in the literature are compared.IntroductionHot deformation in aluminum based materials is done for several technological purposes, such as thermomechanical processing to alter mechanical properties of simple forms, and/or final shaping operations to produce a complex shaped part by means of extrusion, forging, or superplastic forming. In the interest of improving the mechanical properties of aluminum based materials, two microstructural design strategies are commonly used, dispersion strengthening, and composite strengthening. The introduction of fine, stable dispersions is commonly done for high temperature strength, and the dispersions are typically ceramic particles in the range of 10 nm to 1000 nm in volume fractions around 5 vol.% (Higashi et al., 1990; 1991a; 1991b; 1992; Bieler and Mukherjee, 1990; Otsuka et al., 1987; Bieler et al., 1991; Oliver and Nix, 1982). Alternatively, composite strengthening strategies using 10-40 v% of 3 µm to 40 µm ceramic particles provide high modulus and high strength aluminum based materials (Midling and Grong, 1995; Lloyd, 1994; Subramanian et al., 1995)."

Jan 1, 1997

By J. D. Stinnette

Traditionally, airflow requirements for diesel equipment operating in underground environments such as mines and tunnels were determined by multiplying the vehicle power by a ventilation rate that was either mandated by regulations(s) or determined empirically from known quantities. In some cases, utilization factors were further used to adjust (reduce) the total airflow calculations for a diesel equipment fleet. However, in light of the drastic reductions to diesel equipment emissions mandated by the US EPA Tier IV and EURO Stage 4 regulations, there is currently a great deal of uncertainty in the underground mining industry among those responsible for the ventilation of planned new mines or the expansion of current mines. Tier IV engine standards mandate a reduction of DPM and NOx of approximately 95%, but can ventilation rates at mines with Tier IV equipment (or equivalent) really be reduced by a factor of twenty? This paper outlines some of the factors that affect the airflow required for the ventilation of modern diesel-powered equipment and examines how they can be applied in determining a reasonable ventilation rate for Tier IV compliant equipment operating in subterranean environments.

Aug 1, 2013

By J. H. Pateson, D. C. Comrie, D. J. Ritcey

"Geopolymers are inorganic semi-amorphous three dimensional silico-aluminates of the poly(sialate) type (-Si-O-Al-0-) or of the poly(sialate-siloxo) type (-Si-O-Al-O-Si-0-). Polycondensation occurs at low temperatures with geopolymers being stable up to 12oo0 c. Research, development and application technology pertaining to geopolymers is being undertaken jointly with Dr. Joseph Davidovits of The Institute for Applied Archaeological Sciences of Florida, U.S.A. This joint focused upon the chemical Barry University in Miami Shores, research and development program has stabilization and solidification of various waste products through geopolymerization. Of particular interest is the geopolymerization of mine wastes including tailings and waste rock derived from the processing of base metals, precious metals, potash, coal and uranium deposits.INTRODUCTIOND. Comrie Consulting Ltd., in cooperation and technical liaison with CANMET, Ottawa has been testing the application of geopolymers to mining wastes. Corporate efforts to date have concentrated upon reactive acid tailings, principally from the abandoned Kam-Kotia Mine site, and dewatered paint waste sludges. Test work conducted to date has successfully yielded geopolymer treated materials and wastes with increased chemical and structural stability. Wastes containing heavy metals, cyanides, arsenic and sulphur dioxide have been successfully geopolymerized."

Jan 1, 1988

By Terry McNulty

"Previous papers (McNulty 1998 and 2004) have dealt with the causes of successful and less successful achievement of design production rate by new processing plants in the minerals industry. Examination of many case histories has allowed the construction of curves or profiles that represent projects with similar characteristics that equate to differing degrees of care exercised during the project development phase. Simplistically, decreasing care is reflected by increasing risk and a heightened likelihood of poor technical and/or financial performance.This contribution provides an update, including recent case histories, and presents a modified Series 1A curve that includes the best 23 case histories, out of a total of 81 examined, or 28%. This is done to show that some very carefully developed and executed projects can ramp-up quickly and that owners of new projects should avoid being too pessimistic in projecting early cash flow if they are certain that they have done their homework. The role of metallurgical process development in the reduction of project risk is discussed and several financial analyses are presented that express the potential monetary value of a well-designed and professionally executed metallurgical program."

Jan 1, 2014

By A. C. Drost

The mining industry has been put under closer scrutiny in recent years, which has led to the adoption of a plethora of initiatives in countries around the world and by international organizations, some voluntary and others mandatory, governing economic, ethical, social and environmental practices of this industry. In order to plan appropriately, secure project financing, build value and manage risks, it is imperative to identify and understand the application of this new and evolving regime, which can be described under the general label of corporate social responsibility (?CSR?) law, and to incorporate compliance policies into the day-to-day operations of mining companies. Our paper and presentation will describe this new legal framework, which includes both ?soft? law and ?hard? law adopted at the international and domestic level that governs the actions of mining companies, particularly when operating in developing countries. While the notions of hard and soft law may seem abstract and grounded in legal theory, this paper shall demonstrate how these concepts concretely apply to companies in general, and to mining companies in particular. An analysis of the recent case law in this area as well as examples of corporate ?best practices? will illustrate the application of this body of law. As will be demonstrated through the case law, non-compliance of CSR law (both ?soft? law and ?hard? law) can lead to economic penalties, difficulties in accessing capital, loss of social licenses and even the withdrawal of permits and concessions. This confirms that now more than ever, ethics and sustainable practices in mining are fundamental to building a successful business model.

Aug 1, 2013