Search Documents

By M. Duncan

Lightweight, high-pressure cylinders for compressed hydrogen storage are essential components for fuel cell vehicles. Storage volume and mass are two key considerations. Current on-board hydrogen storage systems are based on a maximum pressure of 350 bar. While 350 bar systems are excellent solutions for many applications, some situations require higher storage densities due to space restrictions. As a result, significant research and development work has been expended by cylinder manufacturers, systems providers, testing agencies and automotive manufacturers to develop 700 bar systems with reduced storage volumes. Dynetek Industries Ltd. has proactively developed several 700 bar storage cylinders based on a seamless aluminum liner over wrapped with a carbon fiber composite. This paper presents the challenges and processes involved in the design, testing and certification for Dynetek Industries Ltd. 700 bar cylinders. This paper also provides reasoning for further volume and mass optimization of compressed hydrogen cylinders through the establishment of realistic cylinder usage parameters in standards. In particular, the overly conservative fill life requirement for cylinders is examined.

Jan 1, 2005

By M. B. M. Monte, M. L. Torem, E. R. Pecanha, A. G. Merma

The recent literature has unveiled the potential use of microbial strains in mineral bioprocessing. This study presents the use of a Gram-positive bacterium (Bacillus subtilis) as bioreagent for hematite flotation. The bacterium presents the ability to modify the properties of mineral surface (electrophoretic mobility and hydrophobicity). It was studied the electrokinetic behavior of hematite particles, before and after the interaction with the bacterial cells. The results revealed a shift of the isoelectric point (IEP) of the hematite after interaction with bacterial cells, suggesting a chemical adsorption mechanism. Moreover, after bacterial conditioning, the zeta potential curve of hematite presented high values in the alkaline pH range. The hematite and the bacterial surfaces presented contact angle values around 27.4° and 41.0°, respectively. According to the results, the B. subtilis strain was capable of modifying the hematite surface, and after interaction the hematite surface presented a contact angle value around 46.0°. The flotation tests were carried out in a modified Hallimond tube. The experiments revealed a significant increase in hematite flotability using the Gram-positive strain as bioreagent. The tests pointed out a maximum recovery of hematite in the presence of 600 mg/L and pH 5. Therefore, the results from this study showed the potential use of the B. subtilis strain as a biocollector for hematite flotation, and its possible application in the mineral flotation industry.

Jan 1, 2016

By A. Majumdar, B. Servière, H. Persson

The CCR refinery, which was built in 1931, treats both internal and third party copper anodes to produce 325,000 mt of copper as cathodes. These anodes contain high levels of impurities, such as Ni, As, Sb and Bi, that reports to the electrolyte during the refining step and need to be removed in order to maintain cathode quality and operating efficiencies. In the purification plant, the electrolyte is de-copperized via electrowinning in three stages. In the last stage, the copper content of the electrolyte is reduced to below 1 gpl in order to maximize the co-deposition of As, Sb and Bi with the Cu. This is accomplished with minimum arsine gas generation by using periodic reversal of the current and by controlling the final copper content of the electrolyte. Nevertheless, the possibility of exposure to arsine is treated as a major risk and controls have been implemented to reduce this risk. This paper describes the controls in place at the purification plant, which are being continuously improved through periodic risk assessments and audits. INTRODUCTION The CCR Refinery, which is a part of Glencore Canada Corporation and located in Montreal-East, Quebec, is a custom copper and precious metal refinery, with a capacity to refine 325,000 tonnes of copper anodes per year. Copper anodes are received from the Horne smelter in Rouyn-Noranda, Quebec, Altonorte smelter in Chile and other 3rd party smelters. CCR anodes are produced using the spent anodes from the tankhouse along with purchased spent anodes and copper scrap. The precious metal plant treats the tankhouse anode slime, purchased anode slime, precious metal ingots and Doré anodes from Glencore’s Brunswick lead smelter in Belledune, New Brunswick. CCR products include copper cathodes, silver and gold bullion, a platinum-palladium concentrate, selenium, tellurium dioxide and nickel sulfate. In 1975 an accident occurred at CCR where two employees were exposed to fatal levels of arsine emitted from the then existing purification cells. This process was therefore shut down immediately. Research and development work was then initiated to determine the optimum electrowinning conditions whereby arsine gas generation would be minimized while maintaining high copper and impurity removal efficiencies. It was found that the application of periodic reversal of current (PRC) during the last stage of electrowinning retarded the onset of arsine formation while at the same time allowing the copper concentration to be reduced to less than 1 gpl (Houlachi & Claessens, 1978). A new purification plant was designed based on the PRC technology and was started up in 1976. In addition to the use of PRC electrowinning, the new plant is located in a fully enclosed section of the tankhouse. A special effort was made to design a ventilation system to evacuate the acid mist in addition to any arsine gas. Arsine monitors were installed to measure the emissions from the stack along with arsine levels in the workroom. The arsine monitors and the ventilation system were interlocked with the rectifiers (Thiriar et al., 1983).

Jan 1, 2019

By X. F. Liu, O. Buzzi, Y. Sieffert

This study falls in the context of underground coal fires (UCF) where burning coal can elevate the temperature of a rock mass in excess of thousand degrees. The objective of the research was to experimentally investigate the change in mechanical behavior of a rock when subjected to temperatures up to 900 °C. Several blocks of an Australian mudstone were collected from a mining site in New South Wales, Australia. X-ray diffraction and thermal-gravimetric analysis were conducted on powdered rock in order to determine the critical temperatures at which the main mineralogical changes occur. Then, cylindrical specimens were prepared from intact rock blocks for unconfined compression tests. These rock specimens were then treated by heating in a temperature-controlled furnace at temperatures varying from 100 °C to 900 °C. The heating process consisted of two stages: raising temperature with very slow rate of 1 °C per hour followed by a holding period of 24 hours and then a slow cooling process to room temperature. The compression tests were carried out on treated rock specimens to characterize the change in compressive strength. The macroscopical study was complemented by microstructural investigations via optical microscope, scanning electron microscope (SEM) and mercury intrusion porosimetry (MIP). Results show that the unconfined compressive strength of mudstone decreases with increasing heating temperature up to 450 °C, beyond which it increases. This can be explained by the combined effects of micro cracks and mineral thermal reactions caused by heating process.

Jan 1, 2015

By N. Depountis, Th. Rondoyanni, N. Sabtakakis, K. Kavoura, G. Tsiambaos

"Some typical landslide phenomena in Western Greece, in terms of the geological composition and structure of the affected materials, induced by heavy rainfalls are thoroughly studied and analyzed. The studied cases involved composite landslides on Flysch and Neogene weak rock materials that constitute the most critical landslide prone geological formations in Greece. The studied cases named Platanos, Platanitis and Karya include representative landslide sites as regards to the geological composition and structure of the displaced formations. Thus: (a) flysch formation includes different lithological units as shales, marls, siltstones, sandstones and conglomerates and is closely related to the Alpine orogenesis, suffering intense past tectonic movements and (b) the Plio-Pleistocene sediments include clayey marls, marlstones and siltstones. The investigated landslides , affecting mainly transportation routes, are closely related to heavy rainfalls induced by extreme meteorological events and are controlled by active fault tectonics. Long term movement monitoring using borehole inclinometers and surface benchmarks showed that landslides control was effective only when the proper stabilization measures were taken.INTRODUCTIONLandslides represent a major threat to human life, property, infrastructure and natural environment in most regions of the world. They are recognized by the scientific and politic authorities as having a major socio-economic impact and they represent a significant hazard for the population and the properties in particular locations. Landslide hazard expressed as the probability of occurrence within a reference time period and is a function of the spatial and temporal probability (Varnes, 1984; Guzzetti et al. 1999; Lee and Jones, 2004). The spatial probability of landslide initiation (susceptibility) is mainly related to static causal factors (slope inclination, material properties, etc.), while temporal probability is mainly related to dynamic causal factors such as rain input, increased groundwater levels and drainage, earthquakes, etc. (Van Westen et al. 2005)."

Jan 1, 2015

By F. Parada

During copper smelting and converting processes, slag generated is pyrometallurgically cleaned and then disposed, containing around 1 % of this metal. However, important amount of molybdenum initially contained in concentrates also goes to the slag phase. Research on molybdenum recovery from water granulated slags using acid leaching at low temperatures was conducted to find an efficient way for molybdenum extraction with lower magnetite in the slag. However because of the high fayalite content high acid consumption was found. Molybdenum can be recovered from solution using ionic exchange resins, but high silica content interferes with extraction. Some studies addressed to minimize silica extraction as well as alternatives of selective silica precipitation in order to develop a technically feasible process.

Jan 1, 2007

By G. Riveros

A new, continuous fire refining process for copper has been developed and tested at the 5 tph pilot scale. During oxidation, the blister copper flows through a packed bed of crushed refractory bricks counter-current to a hot oxygen containing gas. The resulting desulphurized copper flows then directly into a packed bed of charcoal for deoxidation. By controlling the air to natural gas ratio, both temperature and reducing conditions can be controlled. Based on extensive laboratory scale measurements of the rate of copper oxidation and reduction, the process concept was developed aided by process modeling and simulation. The industrial-pilot scale installation built at the ENAMI Paipote smelter in Chile, consists of two cylindrical, compact reactors, operating in line, with a designed capacity of 5 t/h of blister copper. The results of the industrial-pilot tests confirmed the feasibility of the new process. The blister copper processing capacity was increased to 10 t/h with satisfactory sulphur removal. The degree of oxidation as well the copper temperature was controlled with relative ease. The specially designed siphon block allowed for smooth tapping of the oxidized copper and separation of refining slag. The reduction of oxidized copper in the packed bed of charcoal appeared to be very effective while control of the degree of reduction according to the height of the bed ensured control of the oxygen content in the refined copper at the required level.

Jan 1, 2007

By Y. Nishida, Y. Nara, T. Ishida

Understanding time-dependent deformation and fracturing in rock is essential, because the information of the long-term stability of rock is required for many sub-surface structures excavated in a rock mass. Time-dependent fracture propagation has been invoked as a potential key mechanism responsible for the increase in seismicity preceding earthquake ruptures. In engineering projects and in preventing natural hazards, the study of time-dependent fracturing is necessary. Subcritical crack growth is one of the main causes of time-dependent fracturing in rock. For silicate rocks, subcritical crack growth has been investigated by various researchers. It has been clarified that surrounding environmental conditions (temperature, humidity, and existence of water) have strong influence on subcritical crack growth in silicate rocks. Therefore, the information of subcritical crack growth in silicate rocks has already been enough. On the other hand, information of subcritical crack growth in carbonate rocks is not enough. Especially, the influence of surrounding environment on subcritical crack growth in carbonate rock has not been clarified yet. In this study, we investigate subcritical crack growth in carbonate rock experimentally using a fracture mechanics testing method. Marble obtained in Skopje in Macedonia is used as a carbonate rock sample. The Double Torsion method is used to measure the crack velocity and stress intensity factor. Especially, influence of water on subcritical crack growth in Macedonian marble is investigated. It was shown that the crack velocity in water is much higher than that in air at the same temperature. Based on the results of subcritical crack growth measurements, the long-term strength is evaluated for marble. It was clarified that the long-term strength in water is lower than that in air in marble. It is concluded that water has a remarkable influence on subcritical crack growth in marble. It is also considered that the long-term stability of carbonate rock masses should be ensured in a dry environment.

Jan 1, 2015

By C. Zangerl, W. Fellin, M. Holzmann, B. Hofer, S. Perzlmaier

"Four deep-seated rockslide systems were investigated and are under surveillance by TIWAG (Tyrolean hydro-electric Company) since the mid-1960s after impoundment of Gepatsch reservoir began. These rockslide systems consist of several individual sliding masses (slabs) which show variable activity from zero to a few centimetres per year. The focus in this paper will be on the findings for the transient deformation behaviour of the Hochmais slab which is part of the “Hochmais-Atemkopf” rockslide system.The rock mass has slid over moraine deposits in the last post-glacial period and was in equilibrium (or slow to extremely slow moving, respectively) until the filling of the reservoir began. During the initial reservoir filling in summer 1964 considerable movements had been observed over a length of 1000 m accompanied with an activation of the Hochmais slab. Geological investigations, additional surface and subsurface measurement showed that the sliding mass is characterized by an en bloc movement and the deformation accumulates within a several metre thick shear zone located within the moraine. In contrast to the deformation characteristics for the first impoundment process (1964 – 1966) where the magnitude of deformation occurred during impoundment, the maximum amount of deformation since 1967 occurs during the drawdown of the reservoir. Based on long term measurement it can be shown that the magnitude of deformations per year correlates with the minimum storage level in the reservoir. Other external influences such as precipitation and snowmelt have no observable impact on the deformation characteristic of the landslide. On the basis of long-term data series it was possible to determine the factors of influence and to elaborate a conceptual mechanical model which describes the transient deformation behaviour of the Hochmais slab induced by the drawdown of the reservoir. The mechanical model considers the reduction of uplift forces in the highly fractured and permeable rock slab during drawdown as well as increasing seepage forces in the less permeable moraine material."

Jan 1, 2015

The reliability of mining systems is generally low due to their harsh working conditions. Currently, efforts for improving mining system reliability are often made in isolation. This practice could substantially limit the effectiveness of the efforts on overall reliability improvement of the mining system. To enhance the overall reliability of mining systems, an integrated improvement approach is necessary. In this paper, we developed a framework for integrated mining system reliability improvement to address this issue. In this framework, there are five major components including data integration, business process integration, hardware integration, software integration, and analysis/decision integration, but we only focus on the integrated reliability analysis which is important to the analysis/decision integration. The reliability analysis considers the interactions between machines, and the impacts of design, operation, maintenance, automation and working environment on the overall system reliability. These multiple interactions present a big challenge to accurate reliability prediction. In this paper, we for the first time systematically investigated integrated reliability analysis approaches for dealing with this challenge using novel models and methods, including covariate hazard models, intelligent reliability prediction approach, and complex system modeling methods. While these models and methods have found some successful applications in other industries, they in general have not been effectively used for the reliability analysis of mining systems. Our study results show that the system integration approach is applicable to mining systems and can be used for developing a computer aided integration system for the implementation of the integrated reliability improvement approach.

Aug 1, 2013

By Th. Hassel

The application of magnesium as an absorbable biomaterial demanded the consideration of the alloy composition, the mechanical properties and the corrosion a special adapted material development in terms of the human biological system. Magnesium for technical applications mostly comprised alloying elements up to 10 wt%. Thereby often metals (e.g. rare earth and aluminum) with high toxic potentials are used to optimize the mechanical properties. To minimize toxic reactions during the degradation of a absorbable magnesium alloy, the Mg-Ca system is being selected and investigated because both elements belong to the mineral nutrients. Rods and small tubes are produced by extrusion of gravity die casting billets (Ca-content 0.4 to 4.0wt%). The positive grain fining influence of calcium and its improvement of the corrosion behavior are additional advantages. The microstructure, the mechanical properties and the corrosion attitude are investigated. The results show that an optimal composition of micro alloyed Mg-Ca and ideally processing parameters lead to 16% strain and a tensile strength up to 185MPa. Electrochemical investigations and measurements of the hydrogen production demonstrate the influence of the Ca-content to the corrosion behavior of the investigated alloys.

Jan 1, 2006

By D. Ibarra, J. Jacob, A. G. Guezennec, P. d’Hugues, A. Archane

The lack of adequate gas mass transfer is a rate limiting step in many bacterial leaching processes. Oxygen often becomes a limiting factor because of its low solubility compared to the high demand induced by sulfide oxidation. One way of increasing the solubility of oxygen in water or in media solution is by increasing the driving force, i.e. raising the oxygen partial pressure in the gas stream supplied to the leach pulp. The use of oxygen is a well-known practice in high-temperature bioleaching reactors (above 70°C) whereas air is usually preferred in medium and low-temperature operations in order to avoid too high dissolved oxygen concentrations which could impact negatively the bacterial activity. The purpose of this study was to investigate the use of oxygen-enriched gas in bioleaching reactors at 40°C in order to improve the gas transfer in the system when operating at high solid load (20% and more). Bioleaching experiments were performed on a sulfide-rich tailing waste (pyrite 60%, copper 0.8%, cobalt 0.06 %, gold 1 g/t) using the “BRGM-KCC” bacterial consortia. The reactor used for the tests was designed on the basis of a new bioleaching reactor concept developed by Air Liquide, Milton Roy Mixing and the BRGM which uses floating agitators to inject gases and to mix and to suspend solids in the bioleaching solution. Two types of tests were carried out: with air injection and with oxygen enriched gas mix injection. The aim of this work was to confirm the capacity of bacteria to grow and to dissolve pyrite in this type of bioreactors in oxygenrich atmosphere, and to compare sulfides dissolution rates during both types of bioleaching tests. The results obtained show that the use of oxygen enriched gas mix does not decrease bioleaching performances compared to air injection. High metal extraction yields were achieved (above 80%). No deleterious effect due to oxygen use was observed on the bacteria despite the high level of dissolved oxygen reached in oxygen tests (up to 14 mg.L-1).

Jan 1, 2016

By Balmer Neilly

Early in my term of office it was announced that my Presidential Address would make particular reference to the subject of Mine Taxation in Canada. With this purpose in view there was drafted a Balance Sheet and Earnings' Statement of a Gold Mining Company. This in turn was submitted to the Dominion Income Tax Authorities in Ottawa and to the Minister of. Mines of each of the several Provinces of Canada. The response to the invitation was not as complete as we had hoped it would be, but the figures that were obtained will be presented during the present meeting, and they constitute, I hope, a sufficient basis for extended study and additional enquiry during the year to come ( 1) . In the form letter that accompanied our request to have the submitted earnings assessed, I made the following assertion: "In this work we have three objects in mind. 1.--We will get direct comparison between the different Provinces in Canada. 2.-We will in this way educate our members concerning taxation as it affects the mining industry. 3.-We will publish the details as to how the assessment is calculated by each body, so that a Mine Manager in the most remote district will have a ready reference to guide him in his annual return to the taxing bodies. As things stand, there is no intention of making this a basis for a critical attack on the present rates assessed. It is intended as an authoritative summary of actual conditions as they presently exist".

Jan 1, 1934

By C. I. Walker

Field tests at a number of large mineral processing operations have been undertaken to better understand the wear life impact of different aspects of pump design, materials of construction and maintenance procedures. Data are presented for wear rates, and typical result variability is explored. To improve the availability of pumping equipment in a milling circuit it is not only important to improve the wear life, but also reduce the variability in the wear life of components so that the incidence of premature failure is lessened. Localised gouging wear due to flow separation and turbulent eddy formation is often the point at which part-holing occurs. A number of improvements to the design of pump impeller and throatbush (suction side liners) to reduce the localised gouging wear are outlined. Also, results are presented on the use of composite materials (mix of metal, rubber and ceramic) for throatbush materials to protect specific areas against wear.

Jan 1, 2012

By B. Hart, D. J. Miller, J. T. Francis, M. C. Biesinger, Smart. R. St. C.

Diagnosis of the surface chemical factors playing a part in flotation separation of a valuable sulfide phase requires measurement of the hydrophobic and hydrophilic species that are statistically different between the concentrate and tail streams. Time of flight secondary ion mass spectrometry (ToF-SIMS) can be used to identify sufficient particles of a specific mineral phase for reliable statistics determining a mean value for each species with 95% confidence intervals (1). Using the region of interest (ROI) facility in the Tof-SIMS software, a mass spectrum from each particle, at 1-2 monolayer sensitivity, is recorded and stored. This analysis is reported for a chalcopyrite / pyrite / sphalerite mineral mixture conditioned at pH 9 for 20 minutes in order to study transfer of copper from chalcopyrite via solution to the other two mineral surfaces since this mechanism can be responsible for their inadvertent flotation in copper recovery. Analysis from mineral selection based on specific ToF-SIMS signals (eg. Pb, Zn, Cu, Fe, Fe/Cu) indicated no statistical difference in the copper intensities on pyrite and sphalerite after this conditioning. Principal component analysis (PCA) of the ToF-SIMS imaging data identifies combinations of factors strongly correlated (positively or negatively) in images or spectra from mass spectra recorded at each of 256x256 pixels in a selected area of particles. PCA is a better method of selecting minerals due to multi-variable recognition. It has clearly separated a statistical difference in copper intensities between the sphalerite and pyrite phases. The method has been extended to samples from an operating plant again with excellent phase recognition and diagnostic surface chemistry.

Jan 1, 2004

By A. Otsuki

"This paper discusses the primary collector adsorption onto a sulphide mineral in mixed collector systems to understand its adsorption mechanism. UV-vis measurements were performed to identify the primary collector concentration adsorbed on pyrite, and the adsorption kinetics under different conditions were compared to distinguish their difference between single and mixed collector systems. Small amount of secondary collector addition prior to the primary collector addition significantly improved the adsorption kinetics of primary one. The result was explained by the combination of two previously proposed mechanisms (i.e., different adsorption site mechanism and multi-layer product mechanism). This study showed UV-vis measurement as an effective tool to study mixed collector adsorption behaviour.INTRODUCTIONCollectors are surfactants composed of heteropolar molecules with a non-polar and a polar group (Lotter & Bradshaw, 2010). In a froth flotation process, the function of collector is to improve the hydrophobicity of target minerals and selectively float them with the aid of gas bubbles. Because of the chemical or physical attraction between the polar group and the mineral surfaces sites, collector molecules adsorb on the particle surface with the non-polar group assigned towards the bulk solution (i.e., water), thus the mineral particle surface becomes hydrophobic (Wills & Napier-Munn, 2006).Thiol collectors are major collectors widely used in sulphide mineral flotation. Potassium amyl xanthate (PAX), dithiocarbamate (DTC), dithiophosphate (DTP), mecaptobenzothiazole (MBT) are some common thiol collectors. Previous studies reported that some mixed collectors systems enhanced the flotation performance (e.g., Bradshaw, 1997; Bradshaw et al., 1998; Rao & Forssberg, 1997). Thiol collector mixtures are often used in the flotation of sulphide ores, and discussed with the synergistic benefits (Bradshaw et al., 1998) which include lowering the total collector dosage requirements, improving the sulphide recovery and the rate of flotation as well as the improving the froth characteristics. The current paper mainly considered the mixture between two thiol collectors (PAX and DTC, considered as a weaker and selective collector, and stronger and less selective collector, respectively (Bradshaw, 1997)) to further understand their adsorption mechanism that should assist in improving the flotation performance of refractory gold ore."

Jan 1, 2016

By M. Ghamgosar, Erarslan N.

Rock cutting includes many unknown parameters which result in different consequences of the different cutting conditions. However, based on the current suggested models for rock cutting, there are some critical parameters that control the fracture initiation and propagation in the rock domain. In general, there are two major cutting tools are used in rock cutting: drag bits and indenters. Different mechanical attacks of cutters result in different fracture models. For example drag bits break the rock parallel to the rock surface, which is called ‘undercutting’ while indenters cut rocks by pressing normal to the rock surface. Both tools cause rock failure by inducing tensile cracks in the rock. However, drag bits induce more tensile cracks compared with the indenters. The full benefits of improvement in rock cutting efficiency will arise from a clear understanding of rock fracture mechanics principles. Therefore, fracture mechanics principles will be applied to the rock cutting as the rock fragmentation process is based on the rock fracturing. The Oscillating Disc Cutting (ODC) has more advantages than drag bits and disc cutters. The forces transmitted back through the cutting head are much lower with ODC. Although ODC attacks rock in much the same way as drag bits, a combination of the oscillating action of the cutter and the undercutting mode produces the lower cutting forces and causes rock fatigue. Fatigue phenomenon in rock has advantages for the rock breaking by applying less effort and energy due to the cyclic loading. The aim of this study is using the Extended Finite Elements Analyses (XEFM) numerical modelling for simulating the ODC cutting with different cyclic loading conditions. An accurate prediction of numerical investigation requires detail laboratory experiments. A series of laboratory tests were performed to obtain the fracture toughness values of our Monsonite rock samples under various cyclic amplitude and frequency values. The numerical results showed different types fatigue damage mechanisms due to the various cyclic loading conditions. Thus, modelling and understanding the crack propagation behaviour depending on different amplitude and frequencies are believed very important for the dynamic rock cutting researches and rock cutting machine manufacturers.

Jan 1, 2015

By J. P. Harrison, K. Gao

It is well known that in situ stress measurements at a given site will generally display significant variability. However, it appears that a robust analysis of such measurements – i.e., one that is faithful to the tensorial nature of the data – is not available. Despite the fact that stress is a tensor, stress magnitude and orientation have long been analyzed separately using classical statistics. In earlier work we demonstrated the applicability of tensor statistics to the analysis of stress variability. Here, we investigate further the difference between tensor and classical statistics with respect to the stress tensor correlation matrix. Our analysis commences with the selection of a series of valid correlation matrices. Then, assuming that standardized tensor components follow the multivariate standard normal distribution, these correlation matrices are used to generate marginal probability distributions of the eigen-parameters (i.e., principal stress magnitude and rotation angle). From these, random stress tensors are generated, their eigenparameters determined, and the probability density distributions of these obtained using both classical and tensor statistics. Our results indicate that, for all correlation matrices, both methods give practically identical distributions for principal stress magnitude. However, the discrepancy between the two methods with regard to probability density distribution of rotation angle is highly dependent on stress component correlation. This discrepancy is usefully quantified in terms of the integral, with respect to orientation, of the difference between the two probability density distributions. This parameter, which we term Area Difference, is closely linked to the magnitude of the correlation matrix determinant, which itself is related to the normal stress correlation coefficient (i.e., ?x ,?y ??). Assuming that Area Difference should not exceed 0.1, we identify the critical determinant for any particular value of normal stress component correlation coefficient. Thus, using published in situ stress data and the obtained critical determinants, we show that for a specific normal stress component coefficient, when the correlation matrix determinant is less than its critical determinant, the more precise tensor statistics should be used to calculate the distribution of rotation angle. These results demonstrate that the customary analysis of stress measurement data may lead to erroneous results, and that tensor statistics appears to be preferred approach.

Jan 1, 2015

By Allan J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of the typical steel wire ropes used for mine hoisting. Steel wire ropes possess properties making them very suitable for mine hoisting including high strength and durability, but have the negative characteristic of being relatively heavy in comparison with their strength. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength-to-weight ratio of synthetic ropes compared with steel ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application, including rope discard methodology and NDT testing. The three phases/projects are: 1) proof of concept with focus on coilability under load (successfully completed in 2012); 2) high speed and load durability optimization & NDT Development; and 3) in-situ mine trial.

May 1, 2013

By R. Roufail

Mineral liberation is accomplished by comminution and is the first step towards achieving successful downstream processes such as flotation or leaching. In metal mining, one of the most effective comminution methods that is used to grind particles below 10 microns is stirred milling. In this paper the study of particle breakage mode vs. mill operating parameters is addressed. Stirred mills' grinding action is mainly attrition, but operation can be manipulated to include breakage by compression or impact loading. Macro and micro analysis of particle breakage and grinding mechanisms are correlated. Macro analyses convey information that relates grinding mechanism to particle size and shape. It is speculated that the breakage mechanism in the horizontal stirred mills is massive fracture for the coarsest particles and attrition (abrasion) close to the grinding limit where the size reduction ratio approaches 1.0. For micro analysis, the particle breakage mode has a direct impact on fracture type either transgranular or intergranular. Intergranular particle breakage leads to higher mineral liberation compared to transgranular breakage. Similar minerals would have more homogeneous properties that convey a stronger bond compared to dissimilar, heterogeneous mineral bonds. Transgranular fracture requires higher energy than inter granular fracture; trans granular fracture toughness of pure single phase mineral is about 10-14 % higher than the intergranular fracture toughness. This communication presents the results of an investigation to assess how operating conditions can affect trans- vs. inter-granular breakage.

Jan 1, 2009