Search Documents

By Serhat Baycan, Mikias Yohannes

"Kuala Lumpur Karst is a complex limestone formation that is characterized by presence of cavities, solution channels, pinnacles and floaters. Basement excavations in such geological formations are usually challenging, mainly owing to the unpredictable rock head depths and potential for groundwater inflow. Any excavation support system should have adequate robustness and water tightness. Traditionally, Secant Bored Pile walls (SBP) with struts are the preferred option for karst ground. This paper discusses a cost effective and innovative alternative solution for a particular site – using Deep Soil Mixing (DSM) and using Contiguous Bored Piles (CBP) together with Ground Anchors (GA). The site, located around one of the busiest areas of Kuala Lumpur, is a 5,700 m2 commercial and residential development. A 16.0 m deep excavation was needed for four levels of basement and excavation support along the 275 m perimeter of the development. Within the site, the depth to rock head varied from 6 m to 19 m. The basis for each solution and conditions for its suitability are discussed in detail. Some design considerations and construction challenges are also presented. The performance of the two retention systems during excavation are presented, together with comparisons versus design predictions. Suggestions for future development are also given. Advantages of this approach compared to other traditional approaches are highlighted.1. INTRODUCTIONThe geology of Kuala Lumpur is among the most complicated and geotechnically challenging formations in South East Asia. The majority of the city falls into the Kuala Lumpur Limestone formation; which is a thick, highly-weathered and cavernous limestone. This formation is pure calcitic to dolomitic in composition, having infrequent schist and phyllite interbedding (Gobbett et al., 1973).The KL limestone has a highly karstic topography dotted with cavities, ravines, interconnected subterranean channels, pinnacles, overhangs, floaters and slump zones (Tan, 2006). This results in erratic bedrock profiles even within short distances. It is not uncommon to see a precipitous rock head incidence within short distances in the same site. In most parts of the City, the bedrock is typically encountered ranging from very shallow depths to about 30.0 m. The exception to this is at the heart of the City, where Kenny Hill formation prevails above the KL limestone. In such cases the limestone bedrock can be encountered much deeper. The erratic rock head profile and the highly karstic nature of the KL limestone makes it a geotechnical challenge requiring careful consideration of suitable engineering solutions.1.1 – Site DescriptionThe site, located in downtown Kuala Lumpur, is abutted by a busy street on the North. Before development, the site previously served as a car park. To the west an access road separates the site from an empty lot; while on the east, the lot is bounded by light weight residential and commercial buildings. On the south side, the site is bordered by a road that separates it from a prominent Shopping Mall in the City. A layout plan and an artist’s impression of the finished development is shown in Figure 1."

Jan 1, 1900

By W. G. K. Fleming

Mr P. Bermingham introduced paper 9.1, describing the development and trials of a new pile load-testing technique that the Authors had termed "Statnamic". The system involved launching a test weight mounted on the head of the pile by igniting chemical fuel in a pressure combustion chamber between the pile head and the test weight. The expansion products from the burning fuel generated large pressures which were used to launch the weight upwards at high velocity. The reaction from this force generates an equal and opposite force at the pile head. This force is typically of much longer duration compared with, for instance, dynamic load testing by drop hammer. In addition the pile experiences a much lower acceleration - typically of less than one g. Because of the long duration blow, the pile is loaded at below its natural frequency and is therefore under a uniform high stress over its full length throughout the duration of the test. The pile behaviour is not dominated by the complex action of an impulsive stress-wave as with standard dynamic testing. The test technique is thus essentially quasi-static. It was anticipated that a ram test weight of 16 tonne would be sufficient to provide the test reaction for a 600 tonne load test. It was pointed out that the device was still at the research stage, but had yielded encouraging results to date. Testing would proceed from model testing and computer simulation to full scale field testing.

Jan 1, 1991

By Tomio Tsuchiya

A construction method of bored steel H piles enclosed in soil-cement columns was developed by modifying steel H piles from the driven pile method and soil-cement walls from the earth retaining wall method, the latter of which produces cut-off walls and reduces noise and vibration during construction. In this method, as shown in Figure 1, rich mix cement paste is injected into the bottom of a borehole which is pre-excavated by a casing auger, then a steel H beam is inserted before it hardens. Since the high vertical resistance of piles created with this method has already been confirmed by loading tests, we have been investigating the applicability of this method for piles used to temporarily support building loads for top-down construction on raft foundations until the raft foundation is completed. However, in the loading tests, the bearing capacity at the lower end of the pile was measured by loading from ground surface on test piles which had friction cut to eliminate the shaft friction resistance. In other words, the loading tests neglected the effect of overburden pressure of soil above the lower end of the pile. To investigate the effect of the overburden pressure on the bearing capacity at the lower end of the pile, loading tests were carried out on a bored steel H pile of lm diameter (test pile) bored in a compacted sandy soil layer with N-value of 100 to 250 at each stage of a three-step excavation. The results show no significant change in the bearing capacity at the lower end of the pile when the depth ratio of the pile is in the range of 5.7 to 22.7.

Jan 1, 1996

By Abhijit R. Sheth, Craig M. Benedict, John Brun, Ara G. Mouradian

"Amtrak recently replaced the 1907-era bascule two-track bridge over the Niantic River between East Lyme and Waterford, Connecticut. The project included new approach embankments, with approximately 2,500 lineal feet of retaining wall along the west approach and 780 lineal feet of retaining wall along the east approach. The paper focuses on the design and construction of the east approach retaining wall, whose alignment is directly adjacent to an existing wetland area which required protection. An anchored prestressed concrete sheet pile retaining wall was selected for the east approach. A combination of concrete anchor piles and ground anchors were used to support the wall. The design of the wall took into account two simultaneous train live loads, support of electric traction catenary structure foundations, and construction live load, while at the same time preventing permanent impacts to the adjacent wetlands. The design considered challenging subsurface conditions, shallow groundwater, the close proximity of the existing operating tracks, construction staging, and storm surge events in Long Island Sound.INTRODUCTION AND PROJECT HISTORYThe National Railroad Passenger Corporation (Amtrak) recently replaced the 1907-era bascule two-track bridge (No. 116.74) over the Niantic River, between East Lyme and Waterford, Connecticut, along the heavily-traveled Northeast Corridor (NEC). The two NEC tracks, which carry over 50 trains per day, run east-west over a narrow spit of land known as “The Bar”, which separates the Niantic River’s marine estuary to the north from the Niantic Bay to the south, before crossing the river. The bay is an arm of Long Island Sound and is occasionally subject to storm surge from hurricanes.The 1907 bridge was built as a replacement for the previous 1891-era swing-span bridge, and was constructed parallel to, and 49 feet north of, the swing-span structure. The two-track 1907 bridge consisted of a single-leaf bascule span and four approach spans supported on stone masonry piers and abutments. The new bridge increases horizontal navigational clearance for marine traffic in the river from 45 feet to 100 feet, and vertical clearance from 11.5 feet to 16 feet above mean high water with the bridge in closed position. The new bridge, constructed 58 feet south of the 1907 structure, features a single-leaf bascule span of 141.5 feet, with an approach span on either side."

Jan 1, 2017

By Y. Z. Wang

Zhengzhou Yellow River Highway Bridge, which is under construction, has a total length of 5550 meters with bored cast-in-place concrete piles as the foundations of its piers which have a diameter of 2.20 m with a length of approximately 65 m. This paper attempts, through the introduction of the said bridge's footing pile design and construction, mainly to give an account of the following points: 1) experiment and research on deep friction pile with a large diameter, 2) calculation of vertical carrying capacity of the pile with a large diameter, 3) analy­sis of horizontal forces the footing-piles of the column-shaped piers, 4) application of normal and reverse-circulation rotary drilling technologies to the construction of bored cast-in-place concrete piles with a large diameter and 5) applying super-sonic impulse on destruction detective device to examine the quality of the pile concrete.

Jan 1, 2010

By Jacob A. Jordan, Rachel M. Garrett, W. Robert Thompson III, James C. Pegues

"Environmental control structures for an existing fossil-fuel power generating plant near Pascagoula, Mississippi faced several design and construction challenges due to space limitations. Conceptual design calculations indicated drilled shaft foundations would likely be needed to accommodate the higher lateral and compressive loads expected under some structures. A maximum drilled shaft diameter of 60-in was preferred due to various space constraints. Smaller diameter drilled shafts were deemed acceptable under structures with more moderate loading conditions. Furthermore, augercast piles were considered where lateral loading was not a governing design criterion.A series of SPT borings and CPT soundings revealed a subsurface profile consisting of soft to firm clays to depths of about 25 feet, underlain by fine to coarse sands. The apparent relative density of the sands was loose just below the clay, with increasing density noted with an increase in depth.Analysis of conventional drilled shafts indicated needed capacities could not be achieved unless shaft lengths exceeded 100 feet. Post-grouted drilled shafts were therefore evaluated to decrease shaft lengths by taking advantage of increased base capacity. Analyses showed the higher predicted capacities needed for some structures could be achieved with this approach. Final design for the project incorporated 90-ft long, 60-in diameter post-grouted drilled shafts; 60-ft long, 48-in diameter post-grouted drilled shafts; and 60-ft long, 48-in diameter conventional shafts. Both post-grouted and conventional trial shafts were installed as part of the detailed design phase of the project. Each trial shaft included CSL integrity testing and Osterberg-cell bi-directional load testing. Load test results revealed that additional base capacity was, in fact, achieved through the post grouting process. The 60-in diameter post-grouted production shafts and the 48-in diameter conventional production shafts have been installed at the site, with the project that would utilize the 48-in diameter post-grouted shafts deferred at this time."

Jan 1, 2015

By D. X. Xu

A pump station was constructed at the food of a steep mountain, very close to a riverside. To protect the pump station from being washed out, and to guarantee the stability of the steep hillside behind the pump station and the safety of the foundation pit when the station was built, cast-in-place R.C. diaphragm walls (Fig. 1) were clesigned in front of and on both sides of the pump station. This wall was 130m long, 0.8m wide and 29m deep. The diaphragm walling on both sides of the pump station served to prevent landslides and to fix anchor piles. The 55m long diaphragm walling in front of the pump station served as a temporary shuttering which kept earth and prevented water from permeating when the pump station was under construction. After the pump station project was finished, static blasting method was used to blow up the wall body which was 10m beneath the ground so that the water from the river could come into the pump station. The remaining wall body below this level was kept to prevent soil from being washed out. [ ]

Jan 1, 2010

By James Warner

Investigations of the sinkhole indicated that the loose, disturbed ground was completely encircled by dense competent core. This confinement substantially increased the effectiveness of the compaction grouting compared to what might have been expected at a "greenfield" site. However, the 8 ft diameter circle shown in the plan view was only the surface expression of the sinkhole proper and the deep, loosened ground actually extended to a larger diameter of about 20 ft. The planned spacing of the grout holes was based on the finite element simulations using a target void ratio of less than 0.3 throughout the compacted ground within a 5 ft radius of the grout injection point. Because of the strong confinement effect, the layout of grout holes included one central primary hole surrounded by six secondary holes at a triangular spacing of about 5 ft. Since the disturbed ground was considered a confined cylinder, it was anticipated that the primary hole would perform the majority of work and the secondary holes would act as check holes, with progressively lesser grout takes as the loose ground densified.

Feb 10, 2003

By Peter Iovino

Unfortunately, I don't know the unit cost per cubic yard of treatment. I reflected on that yesterday and I don't think that we considered the use of micropiles. They could have been an option. The challenge may have been picking up some of the lateral load but I think the micropiles could have been installed on a batter and perhaps extended to rock. We could have considered them, but I do not believe we explored micropiles as an option for this project.

Feb 10, 2003

By Richard E. Sylwester

Evaluating surface and subsurface conditions for marine foundations (bridges, causeways, terminals, etc.) is often done with a limited amount of data. Subsurface information for these projects is primarily acquired using traditional methods, such as boreholes, test pits or divers, which tend to be expensive and limited in the area of coverage. A number of geophysical methods, including precision bathymetry, sidescan sonar, and seismic reflection or subbottom profiling are extremely cost-effective and obtain significantly more data than can be acquired using traditional intrusive methods. These geophysical methods provide detailed surface images and continuous profiles of the subsurface stratigraphy. This information can be invaluable for selecting the best location for geotechnical boreholes and to map potential geohazards such as submarine slides and filled or open scour holes. Offshore investigations conducted for a proposed highway bridge (Knik Arm Bridge, Cook Inlet, AK), the retrofit of two existing bridge (Antioch and Dumbarton Bridges, CA) and a proposed cruise ship terminal (Ketchikan, AK) used a combination of geophysical methods to map water depth, detect and map debris on the seabed, map the thickness of unconsolidated sediment, determine the depth to bedrock and identify potential geohazards such as scour holes. The results of the geophysical investigations will be used to select locations for obtaining geotechnical borings, to extrapolate geologic information between existing or proposed boreholes, evaluate the potential depth of scour and design a pile support pier. Geotechnical engineers, offshore contractors and bridge designers are realizing the importance of the early use of offshore geophysics for (i) site characterization, (ii) to reduce the uncertainty of geotechnical conditions thus avoiding designs that may be overly conservative and thus more expensive and (iii) to assist in selecting locations for geotechnical borings.

May 11, 2007

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 fUsec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases. and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

May 11, 2007

By K. Rainer Massarsch

"Part 2 of 2 (Continued from Summer 2004 edition) By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenVibrations, which are caused by the installation of piles in dry or permeable soils, can cause settlements. The magnitude of settlements depends on several factors, such as soil type and stratification, ground water conditions (degree of saturation), pile type and method of pile installation (driving energy). A method of settlement prediction due to construction-induced vibrations has been presented by Massarsch (2000). However, in many cases, an engineering assessment must be made at an early stage of a project. The following simplified procedure can be used to estimate settlements in a homogeneous sand deposit adjacent to a single pile, Fig. 5. This approach is based on extensive experience from soil compaction projects. It is assumed that intense densification due to pile penetration occurs within a zone corresponding to three pile diameters. The volume reduction resulting from the propagating vibrations will cause settlements in a cone with an inclination 2V:1H, with the tip at a depth of 6 pile diameters. Thus the settlement trough will extend a distance of 3D+L/2 from the centre of the pile, with maximum settlements at the centre of the pile. Maximum settlements, Smaxand average settlements, Smax can be estimated using the following relationship, choosing an appropriate a value of the soil compression factor, from Table 2.The driving energy depends on the method of pile installation, soil stratification and the pile type. The displacement volume of the installed pile has been neglected. The simplified method is applicable for estimating settlements at the perimeter of a pile group. It should be noted that settlements also occur outside the assumed cone, but these are often negligible. The effect of incompressible layers should be taken into account by adjusting the effective pile length."

Jan 1, 2004

By Deepak Pappusetty, Miguel A. Pando

This study is motivated from the increased interest in recent years to explore use of Ocean Energy Converters (OEC’s).OEC’s can be tidal or generate electricity from wave or current action. Design of foundation systems for these OEC’s is a key consideration as it can represent about 35% of the initial installation cost. The primary focus of this paper is related to foundation systems involving monopiles where a key design consideration includes gradual accumulation of pile head deformations beyond serviceability limits of the OEC. This design consideration is important since these foundation systems are often subjected to more than 108 low amplitude repetitive dynamic load cycles during a normal 30 year design life. Research on single model piles installed in sand and subjected to over 104 low amplitude lateral load cycles have shown that pile head displacements and rotations tend to increase gradually with increasing load cycles. This gradual development of pile head deformation is related to plastic strain accumulation in the soil in the vicinity of the monopile. Analytical methodologies based on conventional p-y curves typically cannot predict these accumulated pile head rotations and displacements. Even 3D dynamic Finite Element Analyses may not capture this response for several conventionally used soil constitutive models. This manuscript presents predictions using p-y based methods as well as 3D dynamic finite element analyses. The different numerical predictions are compared to available experimental data. Results from this study show that conventional p-y methods do not predict the gradual pile head displacements observed experimentally. Modified p-y curves, developed for cyclic loading, do a better job than conventional p-y curves but tend to greatly under predict deformation. This is believed to be related to the cyclic load test data used to develop these cyclic p-y curves which involved at most up to 500 cycles and did not include high frequency contents or partial unloading cycles. The 3D FEA captured reasonably well the general observed trends of gradual accumulation of pile head rotation and lateral deformation with increasing constant amplitude lateral load cycles.

Jan 1, 2015

By Md. Nafiul Haque, Murad Y. Abu-Farsakh, Chris Nickel

"This paper presents the results from a pile load testing program for a bridge construction project in Louisiana. The testing includes two 54-inch open-ended spun cast concrete cylinder piles (OECP), one 30-inch open-ended steel pile (OESP), and two (30-inch and 16-inch) square prestressed concrete (PSC) piles driven at two locations with very similar soil conditions. All the test piles were instrumented with vibrating wire strain gauges to measure the load distribution along the length of the test piles and the skin friction and the end bearing were derived from strain gauge measurements. High strain dynamic load tests (HSDLT) were performed on all test piles at different times after pile installations to quantify the amount of setup with time. Static load tests were also performed on the PSC and open-ended steel piles. Due to expected large pile capacities, the statnamic test method was used on the two open-ended cylinder piles. The pile capacities of these piles were evaluated using various CPT methods (such as Schmertmann, De Ruiter and Beringen, LCPC, COFS methods). The result showed that all the methods can estimate the skin friction with good accuracy; but not the end-bearing capacity. Setup was observed for all the piles, which was mainly attributed to increase in skin frictions. The setup rate parameters “A” [The “A” parameter is defined as the rate of increase of pile capacity ratio (Rt/Rto) per log cycle of elapsed time] were back-calculated for all the test piles and the values were between 0.31 and 0.41.INTRODUCTIONDue to greater efficiency (capacity to weight ratio) of the pipe piles, open-ended piles are a viable option to solid piles. However, the behavior of open-ended piles is more complicated compared to the close-ended piles owing to possible formation of “soil plug” inside the open-ended pile. Many researchers have analyzed the behavior of both types of piles for different purposes; however, very few studies in the literature offer the side-by-side comparison of the close-ended and open-ended piles."

Jan 1, 2017

By Emre Biringen

Over the past decades, there has been an increasing recognition of the strategic use of pile-supported rafts in design of heavily-loaded structures to reduce total and differential settlements. However, such a hybrid foundation construction method has not been widely utilized in many countries, including the U.S., due to code limitations. In current practice, the foundation design is based on either (i) the bearing capacity of the raft supported by the subgrade soils, or (ii) solely the pile capacity. This paper addresses the potential use of such hybrid piled-raft systems, where the structural load is shared by both by the piles and the subgrade soils directly beneath the raft, in foundation design of power plant structures. The study assessed some of the characteristics of piled-raft behavior by undertaking three-dimensional finite element analyses of two raft sizes, and various pile layout patterns, including the rafts with piles distributed evenly and only in the central area of the raft. The computer software PLAXIS 3D with the Mohr-Coulomb constitutive soil model was used to facilitate the modeling of such cases. The results presented in this paper indicate how strategically locating the piles could reduce the differential and total settlements.

By Maral Papazian Bedian

"Case 2. 100th Street Bus Depot: Elimination of Deep Caissons in Favor of Spread FootingsThe PROJECTThe 100th Street Bus Depot is a new five-story bus terminal for the New York City Metropolitan Transit Authority occupying one city block in Manhattan between 99th and 100th Streets, and between Lexington and Park Avenues. It replaces a former two-story garage, built in the 1890’s and initially used as a trolley-car barn. The new structure is a steelframed building with concrete floors and includes a partial basement near its middle. The easternmost column line with design loads of 10 MN (1,125 tons) is within 1.5 m of the underlying multi-tube Lexington Avenue subway system. To support the new columns along the subway line, the project bid plans had called for 1 m diameter and 17 m deep drilled shafts. The upper 14 m of each unit would have required 50 mm separation from the surrounding rock to prevent stress from being imposed on the roof and walls of the adjacent tunnel. The column loads were thus transferred to below the base of the tunnel and supported by 3 m long sockets in bedrock. The bid documents contained extensive test boring information, which revealed that the project site was underlain by massive Manhattan Mica Schist bedrock within just 3 m below street level. In fact, the Lexington Avenue two-level and multi-tube subway had been tunneled through this rock circa 1910, leaving an about 6 m thick solid roof over the upper-level subway. The NX rock core recovery values were near 100 %, with average RQD of 75 %.The CHANGEThe Bus Depot project was let as a design/build contract with a very aggressive fast-track schedule. Both the pre-bid preliminary design and the subsequent final design by the Contractor’s own hired design engineers relied heavily on very restrictive codes, including unnecessarily conservative approaches to seismic design. Any suggestion for value engineering change was undesirable and was strongly resisted. Yet, objecting against the blind reliance on codes in foundation design, the author questioned the real need for the deep drilled shafts to support the columns along the subway. The unsupported statement that no stresses from the new structure can be imposed on the roof and walls of the adjacent tunnel was not sufficient reason for the drilled-shaft design. Unconvinced that deep shafts were necessary, the author rushed to MTA’s warehouse where many rows of rock core boxes were neatly stacked. Careful inspection and some simple testing of the rock cores with the blows of a geologic hammer gave support to the reservations about the design. Later, as expected, the schist bedrock at this site was found to be hard to very hard with unconfined compressive strength values estimated to range from at least 70 MPa to over 100 MPa (10,000 psi to 15,000 psi). The tensile strength of the rock was assessed to be minimum 5 MPa (750 psi)."

Jan 1, 2003

By Abolfazl Eslami, Samieh Rezazadeh

"Semi-Deep skirted foundations are considered to be a viable option for a variety of onshore and offshore applications. It is necessary to determine appropriate foundation configurations that allow loads to be transferred safely to the surrounding soil. For this purpose the bearing capacity and stability analyses subjected to combined vertical, horizontal and moment loadings must be found. In this paper the vertical undrained bearing capacity is estimated via finite element analyses. The circular skirted foundations with different geometries considering embedment depth (embedment ratio between 0-2) and size effects (diameter equals to 5, 10, and 20) have been studied. Stress field, kinematic mechanism accompanying failure and bearing capacity factors for total, end and shaft resistance in semi-deep foundations with various embedment ratios are investigated. Furthermore, two probable mechanisms i.e. internal flow and soil plug for estimating foundation capacity for design purpose in practice have been assessed. Comparisons with different research works including conventional methods, upper and lower bound approaches, and finite element analyses have indicated that the conventional methods underestimate the bearing capacity due to ignoring the significant role of shaft resistance. Determining appropriate economic foundation configurations to transfer loads safely to the surrounding soil is a major issue in geotechnical engineering. Shape and dimension of foundations, embedment depth, soil characteristics and applied loading, all affect the foundation performance. Recent studies have shown that for foundations with large breadth and of D/B between 1 to 4, kinematic mechanisms and failure modes are different from the two main types of foundation (i.e. shallow and deep). Therefore, D/B factor must not be considered as the only factor for defining foundation type. ""Semi-Deep foundations"" are another foundation category distinguished based on their performance. This relatively new concept is becoming increasingly an optimum alternative for shallow and deep foundations to support structures especially in accessible depth. As illustrated in ""Fig. 1"", different types of semi-deep foundations consist of:"

Jan 1, 2017

By Frank Haehnig, Kurt Kogler

"With a height of 200 m, a crown width of 626 m and a concrete volume of 1.6 million m³, the Kölnbrein Dam in the upper Malta valley in Carinthia / Austria is the largest concrete dam in Austria. Boasting a storage capacity of 200 million m³ with a received water load of 54 MN, this is one of the strongest arch dams in the world.During its construction from 1974 to 1977, the dam was equipped with a comprehensive monitoring system capable of comparing developing deformations and stresses with the design values.With a planned reservoir level of 1,900 m a.s.l. the dam saw the reservoir level of 1,860 m a.s.l. breached in the year 1978. This led to extremely high seepage losses of up to 200 ltr/sec and a rise in the foundation water pressure up to 100% of the dam’s height. These observations were caused by the development of horizontal cracks in the area of the middle dam blocks, between the lowest inspection walkway and the waterside.As a consequence, power plant operations had to significantly be reduced and a number of additional measures were carried out – though these did not lead to the desired sealings.The developer subsequently decided that the dam should undergo a general rehabilitation from 1998 to 1994 in accordance with a concept developed by Professor Lombardi. This concept involved erecting a 50 m high support structure with a concrete volume of 500,000 m³ on the airside of the dam, along with the addition of neoprene bearings to transfer 1.2 million tons of the horizontal load. These measures were able to reduce the deformations in the dam enough so that mostly load-bearing injections into the cracks in the dam’s concrete could successfully be carried out by way of targeted grouting measures using injection resin (RODUR) specifically developed for this purpose.In the years 1998 - 1994, a total of 130,000 m of grouting, monitoring and control drillings were executed, and around 200,000 kg of synthetic resin was injected into the cracks in the dam’s concrete.These measures have ensured the dam‘s uninterrupted operation since 1994. A number of small re- injections were again carried out on the contact surface in the years 2011 and 2012."

Jan 1, 2016

By Murad Y. Abu-Farsakh, Md Habibur Rahman

The properties of all natural soil deposits are highly variable, and they are rarely homogeneous. Cone penetration tests (CPT) were used to assess the site variability, which was then incorporated into the Load and Resistance Factor Design (LRFD) of pile foundations. Data from six project sites with multiple CPT tests conducted at various locations were collected for this research. The semi-variogram was used to assess the spatial variability of CPT data (corrected tip resistance, qt) for each location. For each location, the coefficient of variation due to spatial variability (COVR,spatial) was calculated. From COVR,spatial and COVR,method, the total coefficient of variation (COVR,total) for each site was calculated, which was then used to calibrate the resistance factors (ϕspatial, ϕtotal) for use in LRFD pile foundation design. The findings of this study demonstrated the importance of using site variability in LRFD pile design. For sites with lower site variability than the design method (i.e., COVR, spatial < COVR, method), the value of the COVR, total will be decreased, and hence the resistance factors (ϕspatial or ϕtotal) will be increased (credit), and vice versa.

Sep 8, 2021

By Mohamed A. Eliwah

This paper deals with the determination of hydraulic conductivity of the coastal coralline limestone aquifer of Jeddah, Saudi Arabia. This coastal area has witnessed urban development and establishment of towers which requires deep foundations, excavation and dewatering of huge quantities of unconfined groundwater. It is occupied with successive layers of soft detrital and consolidated massive cavernous coralline limestone of the Quaternary age. These layers are encountered at a depth of 1.5m and extend for more than 100m. Hydraulic conductivity values were obtained by analyzing the pumping tests data under steady and transient state conditions. Hydraulic conductivity values help in selecting the proper and safe dewatering system, as well as determination of discharge rates and quantities of groundwater to be withdrawn. Test results obtained from two surveyed sites showed that the values of hydraulic conductivity are greatly variable. It ranges between 118.1 and 1559.6 m/day at the first site, whereas at the second one it ranges between 94.6 and 350 m/day. These high values are attributed to the cavernous nature of the water-bearing formation. Jeddah city could be divided into three different dewatering zones extending from north to south parallel to the coast line. Well point dewatering system could be applied in the first zone while ditches and sumps are the most suitable dewatering method in the second and third zones. Dewatering using deep wells in such highly permeable formation will require withdrawal of huge quantities of water which will be accompanied by washing out fine sediment filling the cavities in the surrounding areas. This will badly affect the nearby buildings through settlement, crakes and other structural damages. Therefore, construction of grouting plug/blanket with thickness of 3.0 m at a depth of 20.0 m is recommended. This depth will be enough to support the plug against the hydrostatic pressure. Moreover, it is highly recommended to transfer the site into closed box, by using diaphragm walls or secant bored piles.