Search Documents

By J. L. Goen

The Saint Joseph Hospital of Bellingham is located on a site underlain by glacial outwash. The construction of a five-story tower addition above an existing two-story wing was supported by five large trusses that impose a 1600 kips (7117 kN) column load on five pile caps in the courtyard of the hospital and on the new pile caps inside the existing MRI laboratory. The exterior columns of the trusses and the new parking garage addition were supported on conventional auger cast piles installed with conventional equipment. Helical Pulldown® micropiles were selected for use in the courtyard and the MRI laboratory because lightweight installation equipment (maximum unit weight of 7.5 kips (33.3 kN)) had to be used and it was required that no spoils be produced. The installation equipment was lifted into the courtyard by the jobsite crane. Sixty Helical Pulldown micropiles were installed for the pile caps in the courtyard. The pile caps inside the hospital were supported on 240 Helical Pulldown micropiles. Initial compression test indicated an allowable load for the micropiles to be 55 kips (244 kN). However, retest at a later date resulted in an increased allowed design load to be 85 kips (378kN) reducing the number of micropiles required by more than fifteen percent.

Jan 1, 2004

1.1 The parties agree to submit all claims, disputes or controversies arising out of, or in relation to, the interpretation, application or enforcement of this agreement, including dispute resolution procedures, to sequential mandatory discussion, mediation and arbitration for resolution of all disputes before, and as a condition precedent, to self-help, arbitration, judicial action or other remedies. This mandatory procedure will resolve each dispute within one-hundred (100) calendar days. Any deadline falling on a federal holiday or weekend will be the next working day. Breach of this disputes process shall constitute a material breach of contract for which the aggrieved party may recover all costs, including attorneys fees, interest and other expenses necessary to resolve the dispute through litigation. The obligation to discuss and then mediate and arbitrate covers all disputes arising from every aspect of the Project to be built by the owner, including, but not limited to, design, engineering, bonding, indemnification, labor, material and services, and the acts or omissions of any related party for whom a party to this agreement may stand responsible.

Jan 1, 1994

By M. R. Madhav

The ultimate pullout capacity of single batter piles has been presented in literature in three contradictory trends. These trends are: the pullout capacity of a single batter pile increases, remain almost constant, or decrease with increasing the inclination angle of the pile. The present paper presents a theoretical study which explained these trends in terms of existing initial stress condition and the earth pressure coefficient at rest. The paper also presents a form of guideline for predicting the pullout capacity of inclined piles based on simple field and/or laboratory tests.

Jan 1, 2010

By C. D. Thompson

Pile load test programs were carried out in 1984 and 1985 at Stelco's and Dofasco's Steel Making Plants in the Hamilton Bayfront area. 323.9 mm outside diameter by 9.5 mm wall thickness Grade 3 steel closed-end pipe piles were driven to practical refusal at depths of 21 to 30 m in very dense silt till with Delmag D30 open-end diesel hammers. Ultimate bearing capacities of up to 5330 kN were proved by dynamic monitoring and static load tests. Allowable bearing capacities of 1780 kN were achievable on production piles without undue difficulty. It was found that the impact stress at the top of the pile was controlled by the yield strength of the steel rather than a useable upper limit based on the modulus of elasticity. A bearing to impact stress ratio of 1.2 at practical refusal was observed to be reasonable but conservative at this site, and is felt to be generally applicable for piles driven to practical refusal elsewhere. Dynamic monitoring during production pile driving was able to show that apparent relaxation was caused by pre-ignition of the hammer when visual observations indicated that pile driving was proceeding satisfactorily.

Jan 1, 1987

By Filippo Maria Leoni, George Filz, Wesley Schmutzler, Matteo Bertoni

"The US Army Corps of Engineers selected the Deep Mixing Method (DMM) for the required stabilization at the LPV 111 Project (New Orleans, USA). DMM was used for ground improvement/foundation strengthening and consequently to stabilize and support the burden of the new levee. Two different technologies were used: Trevi Turbo Mix (TTM) and Contrivance Innovation Cement Mixing Columns (CI-CMC). LPV 111 is the largest soil mixing project to date in the USA with its more than 18,000 elements installed to a depth of up to 67 feet for a total of 1.7 million cubic yards of treated soil. The preparation and execution of the project presented many challenges from various points of view. The little time available to complete the job led to the simultaneous utilization of eight deep mixing rigs and batch plants which worked 24 hours per day, 5.5 days per week on a stretch of land approximately 5.3 miles long. Given the imposing geographical extent of the project, a four phase laboratory programme and five field validation test programmes, conducted in as many different areas of the project, were completed to design and optimize the grout mixes and the installation parameters. The massive quality control/quality assurance testing programme produced over 500 drilled core holes and over 5,000 tested specimens in order to determine unconfined compressive strength (UCS) and uniformity of the DMM elements. This paper has the purposes of describing the tremendous challenges encountered and providing valuableinformation that may be useful for other future projects, including details not previously published.INTRODUCTIONReach LPV-111 is part of the Lake Pontchartrain and Vicinity Hurricane Protection System designed to protect the city of New Orleans and the surrounding areas from the surge that would accompany a 100 year hurricane event. LPV-111 measures approximately 8.5 km (5.3 miles) long, of which 7.2 (4.5 miles) extend along the north bank of the Gulf Intracoastal Waterway (GIWW) and the remaining 1.3 (0.8 miles) run north and terminates at the CSX Railroad Gate. The Bayou Sauvage National Wildlife Refuge borders the levee on both sides (Fig. 1)."

Jan 1, 2015

By Q. M. Huang

In 1979 our company undertook the project of infra-structural work of White Swan Lake Hotel, (International class ) Guangzhou. Visit to the site showed that it was situated at the riverside, covering an area of 54,000 M2 with 30,000 M2 of which reclaimed from Pearl River. The material used for reclamation was black sand which was dredged from the nearby riverbed. The sand had the properties of high permeability and very low internal friction. The basement of the building was 6.2 m below ground level and 3 m lower than the riverbed. Apart from the pile foundation, a diaphragm wall was to be constructed prior to the commencement of excavation work for basement. A feasibility study was carried out to determine the method of construction which would maximize utilization of the plants and equipment that were available in the execution of the aforesaid foundation works. This report concerns only the construction of the diaphragm wall and the performance of the plants employed. A detailed delineation of the construction method is herein discussed

Jan 1, 2010

By Tianfei Liao

Extensive site investigations revealed that abandoned shallow mine workings exist under a site planned for construction of a major new facility. Since the mine voids were susceptible to collapse, they were stabilized by grouting. After completion of the mine remediation, three types of deep foundations (micro-piles, auger-cast piles, and drilled piers) were considered for this site. Micro-piles spread the load via the bond between the pile and the bedrock. Without significant length socketed in rock, the axial load of auger-cast piles and drilled piers has to be concentrated on end bearing. Although spreading the load is preferable in this environment, economic consideration dictated the choice of drilled piers for construction.

Jan 1, 2009

By D. Barber, A. D. Miller, P. A. Bray

The project was to develop an area within the existing West County Wastewater Treatment Plant which would enable the construction of a new Raw Wastewater Pump Station (RWPS) with a footprint of approximately 85 feet by 190 feet and a foundation depth of about 82 feet below grade and a new Short- Term Detention Basin (STDB) with a footprint of about 80 feet by 130 feet and a foundation depth that varied from approximately 3 to 24 feet below grade.. The excavation support system had to be designed to withstand both normal and the 100-year flood elevations. A Reinforced Soil-Cement Wall (RSW)was chosen to provide a hydraulic barrier which consisted of a single row of soil-cement elements installed along the perimeter of the area to be excavated. Steel wide flange beams were installed on 4 foot centers to support construction loads and be resistant to the lateral forces of the soil and hydrostatic pressures. The RSW was installed to a maximum depth of 104.5ft using a triple-auger drill rig with mixing paddles with a 2ft key into weathered shale providing a cutoff wall consisting of 53,150 square foot of treated soil. The project was to provide the initial design of the excavation support for the pumping station excavation support system and groundwater cutoff. There was 534 linear foot of soil-cement-bentonite wall installed and 106 - 80 foot long W21 x 121 wide flange beams installed on four foot centers into the alignment of the wall. Each element was drilled down into the weathered shale to obtain groundwater cutoff. Derek R. Guthrie Water Quality Treatment Center Pumping Package is the site for a new pumping station that will service Louisville, Kentucky residents. After unplanned long term exposure into the winter, the effects of freeze thaw cycles were evident.

Jan 1, 2017

By Luo Yang

A one-dimensional wave equation based algorithm for estimation of shaft and toe resistance of driven piles using High Strain Testing (HST) data is presented. The pile is represented by a uniform elastic bar, while the soil around the pile is assumed as a homogenized isotropic medium, and Smith model is adopted to represent soil-pile interaction in the wave equation analysis. In most cases, the displacement of pile particles along pile shaft is greater than recoverable soil deformation (i.e., soil quake in Smith model). Therefore, static shaft resistance could be reasonably assumed to be totally mobilized during pile driving. Smith damping factor is used to account for combined dynamic and rate effect. Force and velocity time histories measured at the pile head are used as input boundary conditions in an analytical solution of the one-dimensional wave equation. As a result, two unknown parameters, static shaft resistance and Smith damping factor, can be incorporated into the one-dimensional wave equation and determined analytically for the time duration prior to the first downward wave reaching the pile toe. Then, soil resistance and Smith damping factor at pile toe can be further determined. The advantage of the proposed analysis technique is that the Smith damping factor and the static soil resistance can be directly determined based on the closed-form solution of the one-dimensional wave equation, which is computationally efficient. Numerical examples are given to illustrate the use of the proposed method to determine the pertinent Smith model constants and the static resistances.

Jan 1, 2006

By Chris Sammon

The Block 75 portion of the City Creek redevelopment project in Salt Lake City required multiple shoring walls surrounding the 6 acre site constructed to depths ranging from sixty-five to ninety feet below original street grade. Shoring for the project was challenging due to site soils consisting of cobbles, sands and gravels, interlayered lakebed silty clay and fine sandy silt with incised stream deposits of silty/clayey sand and gravels combined with a high groundwater table. Moreover, several abutting structures each with a unique foundation system would be directly or indirectly supported by the shoring system. Three sections of interest are the shoring walls constructed at Main Street, Deseret Trust Building and Eagle Gate Tower. Main Street shoring extended to as much as sixty-five feet below street grade and utilized existing basement walls anchored in place in the upper zones with soil nail walls with pre-installed vertical elements for face stabilization below. Data are presented which illustrates the effect dewatering had on the settlement of the Main Street Shoring. The Deseret Trust Tower shoring supported a 12 story, historical masonry building. Site conditions dictated a separate design for the east side and the north side of the building allowing comparison of relative performance between these walls. Settlements of this structure were controlled by installing micropiles through the 90 year old structures spread footings. Shoring for the Eagle Gate Tower was to be constructed immediately adjacent to a mat supported 22 story high rise structure. This shoring system combined secant piles, ground anchors and incorporated existing abandoned-in-place pipe piles with infilling high pressure jet grouting to create a cutoff wall and eliminate the adverse impacts of dewatering below this sensitive foundation.

Jan 1, 2010

By Andrew Malinak, William Perkins

Seattle’s Elliott Bay Seawall protects the 1½ miles of downtown waterfront between South Washington and Broad streets. The seawall supports the urban waterfront and infrastructure, including the Alaskan Way Viaduct and Alaskan Way, access to historic waterfront piers, and numerous essential buried utilities. Most of the original seawall was constructed between 1916 and 1936 over soft/loose non-engineered fill, estuary, and beach deposits. The majority of the original seawall was a pile-supported timber relieving platform that extended up to 60 feet behind the face of the wall (Figure 1). With maximum spacing between the timber piles of 3 to 5 feet, a virtual forest of timber piles were driven for the original wall.

Jan 1, 2018

By Masanoub R. Fujioka

A brief discussion of the methodologies involved in dewatering practices, particularly as used in Hawaii in coralline formations. A description of early dewatering practices includes a number of case histories; later dewatering practices also are detailed with case histories. There were disasters and some successes. Grouting generally was not successful. Deep wells are technically feasible and generally the economical solution to deep basement construction.

Jan 1, 1986

By Cory J. E. Yacyshyn

Anchored steel pipe piles are being used more frequently in British Columbia for shoreline projects such as public ferries, cruise ship docks, containership terminals and locally in the expansion of the Vancouver waterfront convention center. While a 36? diameter driven pile may provide adequate compression loads it will not always achieve enough penetration to provide the required tension loading. That is why bundles of threaded anchors or strands are drilled through the center, past the pile tip, and anchored into the underlying strata. Drilling up to 250 feet deep through the piles in variable water bearing strata presents challenges. Southwest Contacting Ltd. (SWC) recently completed the three largest anchored pile projects in BC; Vancouver Port and Convention Center Expansion, Vanterm Container Terminal and the new Prince Rupert Cruise Ship Terminal. This paper will present the separate challenges encountered drilling the anchors. At Prince Rupert, the recently completed Northland Cruise Ship Dock ultimately required a cased system to drill and install triple thread bar anchors. When 200 foot long steel pipe piling was unable to penetrate the highly fractured gneiss/schist bedrock to obtain a seal and consolidation grouting was unsuccessful, a modified cased system was advanced deep enough into the rock to eventually seal. The 3-#20 bars were changed to 12-strands since the bars wouldn?t fit through the smaller cased hole. The options were limited because each dolphin only had enough room for a small hydraulic drill rig that wouldn?t have the power to fully case the holes. The Canada Place Pier Extension in Vancouver?s Harbor led to the development of an innovative tip design used later at Vanterm. The 36? diameter steel pipe piles were driven closed end but modified to permit drilling through a concrete plug at the base. The driving of the piles at Canada Place often knocked out the plug so we were faced with 50 feet of sand up inside the pile when the drilling started. This led to discussions on how to safely remove the sand, solidify the tip, and continue drilling to get past the tip without undermining the pile. Finally, Vanterm Berth Extension was completed with a unique drilling system because the pile tips stopped in hydraulic sands, as opposed to the native till. We were faced with advancing the casing to the till without undermining the base of the pile. With 100 psi water pressure at the pile base after we broke through the concrete plug, the trick was to prevent charging the sand with our 250 psi air which liquefies it and forced it up our drill casing. And of course, it has to happen just before Christmas holidays!

Jan 1, 2004

By Jean-Louis Briaud

The following is a summary of a very recent report prepared at Texas A&M University for the National Cooperative Highway Research Program and entitled "Downdrag on Bitumen Coated Piles". Anytime the soil settles more than the pile, downdrag or negative skin friction will develop. The load in the pile increases with depth up to a certain point and then decreases down to the pile point. This phenomenon has been quoted as being the number one culprit for deep foundation failures. In Chapter 1, an introduction to downdrag is given. The most common criterion for downdrag is to consider it in design as soon as the settlement of the soil surface after pile driving exceeds 0.5 in. Coating piles with bitumen is an effective way of reducing downdrag forces and therefore allows to use smaller piles for the same load. This results in cost savings. Coating piles with bitumen increase the cost of piles by about 33% and therefore the decision to use bitumen is generally based on economic considerations.

Jan 1, 1989

By Brian Langdon

The DRIVEN GROUT PILE was developed in 1989 by DeWitt Construction, Incorporated. This piling essentially consists of a cost-in-place concrete piling that reacts on a steel boot that is driven to bearing. This report will describe the driven grout pile, its background and its installation. The advantages and disadvantages of this system are also discussed. Finally, the results of actual field installations are presented and discussed. BACKGROUND The DRIVEN GROUT PILE was developed out of a need for a low-cost high capacity piling (100 ton) that could be installed with ordinary pile driving equipment. This search was motivated by attempting to incorporate the material economy of an auger-cast piling with the "empirical load test" of a driven pile. Typically, the least cost material for piling in the 100 ton range is concrete (grout). A grout shaft with minimal reinforcement can withstand a compressive load of 100 tons for a material cost in the range of $6.00 to $8.00 per lineal foot. A pipe piling with a capacity of 100 tons has a unit material cost ranging to $13.00 per lineal foot. The marriage of these two advantages resulted in the DRIVEN GROUT PILE. A pile that utilizes the economy of a reinforced grout shaft and has the loading confidence of a driven pile.

Jan 1, 1990

By Joanna Bzówka

Nowadays, there are some new requirements for the supermarket floors. The floors are loaded by high point- and moving-loads. In spite of this fact, it is necessary to ensure the stiffness of the floor and the stiffness of its support. When pile foundations are designed in the case of weak soil, the piles are recommended under the foundations of the supermarket and also under the floor layers. The example of foundation of a typical supermarket located on long­standing municipal dumping ground is presented. Indirect foundation - CFA piles, 0.5 m in diameter and 4.5 to 20.0 m long, was de­signed. Fifteen trial loading tests were carried out.

Jan 1, 2006

By Joel Moskowitz

In 1990, the United States General Services Administration (GSA) issued a contract for design and construction of a new federal court building in New York City. Mueser Rutledge Consulting Engineers (MRCE) served as Project Geotechnical Engineers. The project site is in the historic government district at Foley Square. It is surrounded by the New York County Courthouse to the west, an existing federal prison building and federal courthouse across Pearl Street to the south and southwest, an office structure to the north, and a residential tower to the east. The interior of the site was crossed by streets which have now been demapped. As with many urban sites, this site was previously occupied by tenement buildings or industrial structures demolished near the turn of the century. Remains of old building foundations were exposed during construction excavation. In addition, buried fuel oil tanks servicing the adjacent courthouse were removed and the usual assortment of urban utilities had to be relocated for the new building foundations. Ground surface elevations vary from about 4.5 to 6 m above the local Mean High Water Datum Plane.

Jan 1, 1996

By J. Matos e Silva

The paper refers two examples of structures located in seismic areas (Cases 1 and 2). The first one (Case 1) is the Torroal Bridge, located about 100 Km South of Lisbon, in the road Troia-Grandola. The horizontal loads due to the seismic actions were mainly carried by an anchor curtain connected, to the abutments, by reinforced concrete struts-ties. For the some purpose diaphragm walls were also placed under the pile caps of the column foundations. The second one (Case 2) refers to a building located about 50 Km South of Lisbon, at Sesimbra, near a cliff. To reduce the horizontal displacements of the structure due to seismic actions, in order to prevent the endangering of the cliff stability, an anchor curtain was adopted and connected, to the structure, by prestressed anchors.

Jan 1, 1996

By Peter O. Wilkinson

Ascot Racecourse in the UK is a major international venue for horseracing. The racecourse is being redeveloped to provide entirely new public facilities. The development includes the construction of a new grandstand. A site investigation was earned out comprising mainly cone penetration testing. The site is underlain by the Bagshot Formation, comprising predominately cohesionless deposits of medium dense becoming dense, silty fine to medium sand, containing occasional layers of clay. Shallow foundations would present uncertainty regarding total and differential movement; hence a piled foundation solution was chosen using a continuous flight auger (CFA) piling system. The possibility that piles may found either directly on or within the influence of cohesive material suggested uncertainty regarding toe resistance. In order to measure shaft friction, an instrumented preliminary test pile was undertaken. The results were compared to published correlations of cone and shaft resistance. This approach resulted in a net saving in terms of pile length which resulted in optimum value engineering and hence a cost saving to the client.

Jan 1, 2006

By Paul M. C. B. M. Cools, Martin Th. van Staveren

In 2010, the 5-years joint industry programme Geo-Impuls started in the Netherlands. The ambitious goal of this programme is to reduce geotechnical failures in our civil engineering projects by half in 2015. In the Geo-Impuls programme over 40 client organizations, engineering firms, contractors, research institutes, and universities are involved. In a risk-driven way, and based on top risks and dilemmas, the participants defined three central development themes. These themes are (1) contracts, for dealing with legal issues, (2) geo-engineering, for dealing with technical issues, and (3) communication, for paying attention to differences in risk perception by the human factor. In total 12 Working Groups contribute to these themes by producing one or more specific tools. These provide practical solutions for how to deal with contractual, geotechnical, and communication issues. The tools include working processes, guidelines, best practices, as well as some instruments. The development of these tools, as well as the available results, will be presented in this paper. From the start, Geo-Impuls embraced geotechnical risk management (GeoRM) as the risk-driven way of working for geotechnical engineering and construction. Over the past years, GeoRM and its supporting tools were already successfully applied in several projects. Therefore, the paper also describes also the GeoRM implementation process, including the quality assurance and control. Finally, the effectiveness of GeoRM will be discussed, by summarizing an analysis of all published geotechnical failures and accidents in construction projects in the Netherlands, which decreased substantially over the past 4 years.

Jan 1, 2017