Search Documents

By Akira Usui

Platinum is one of the most rare elements in the earth?s crust, but it is significantly enriched in some hydrogenetic ferromanganese crusts in the ocean. The element is essential to the electric industry and is believed to be of importance as a raw material a future fuel-cell industry. The earlier reliable chemical analysis of platinum-group elements (PGE) of ferromanganese crusts have indicated a variety of concentrations of Pt in the range of 100 ppb to a maximum of about 1 ppm, but little is known about the elemental abundance in ferromanganese crusts on fine-scale, or the geochemical behavior and form of the element. The chemical and mineralogical forms of platinum and its group are important in planning the methods of mineral exploration and extraction of the elements from of ferromanganese crusts. We attempted to characterize the distribution pattern within a cobalt-rich crust on the fine to microscopic scales by using reflecting microscope, scanning electron microscope/energy-dispersive spectroscopy, electron microprobe X-ray analysis (EPMA), ICP-mass spectroscopy, X-ray absorption near edge structure (XANES), small-focus XRF, and X-ray diffraction (XRD). These data indicated a wide range of Pt concentration from 150 to 700 ppb within a crust, though we found no distinct inter-element correlation or mineralogical control. Under the reflecting and electron microscope, no distinct Pt-bearing minerals or particles were identified. Small-focus XRF indicated no uneven distribution in any particulate matter, but all areas are less in abundance than the detection limit of about 10 ppm. Our tentative conclusion is that zero valence Pt0 (as suggested by XANES) is dispersed in the form of submicroscopic material most probably within ferromanganese minerals, and therefore, Pt-rich mineral particles may not be a major carrying phase.

Jan 1, 2005

By Stanley R. Riggs

Onslow Bay is a broad, shallow, high-energy shelf system bounded by the Cape Lookout and Frying Pan shoals. It is generally a sediment-starved shelf system dominated by hardbottoms with a scattered and discontinuous veneer of mobile Holocene sediments. Phosphate-rich beds of the Miocene Pungo River Formation crop out in a belt 150 km long and up to 50 km wide across the continental shelf in Onslow Bay, North Carolina. Previous research has demonstrated that a few of these beds contain vast quantities of potentially economic phosphate resources that occur in the surface and shallow subsurface sediments. Onslow Bay contains five phosphate-bearing beds predicted to include up to 20.7 billion tons of in-place phosphate concentrate with total sediment grades ranging up to 22.9% P2O5 and adjusted average concentrate grades of 29.8% P2O5. These phosphates are lithologically and chemically similar to phosphates currently being mined in the nearby Aurora phosphate district in North Carolina. Various lithologies of the Pungo River Formation and associated rock units of Oligocene and Quaternary age crop out on the sea floor to form extensive hardbottom habitats that dominate almost 100% of Onslow Bay. A large proportion of these hardbottoms appear to be sea floor deserts, whereas others are virtual oases with rich associations of benthic organisms. These important differences in benthic community structure appear to be greatly influenced by one or more of the following variables: 1) geologic framework (geologic formation, hardbottom composition, morphology, and spatial orientation relative to dominant currents and waves), 2) texture, movement, and accumulation of surface sediments, and 3) flow rates and chemical composition of discharged submarine groundwater.

Jan 1, 1992

Massive sulfides discovered in 1991 and further explored in 1993 in the eastern Manus back-arc basin, north of Papua New Guinea, represent one of the few modem seafloor occurrences known to he associated solely with highly siliceous volcanic rocks. As such they are very close analogs of ancient volcanogenic massive sulfide (VMS) ore deposits, and hence an excellent natural laboratory for developing new approaches for land-based VMS exploration. The Manus Basin lies between the active New Britain subduction zone and volcanic arc to its south and the opposed inactive Manus subduction trench to its north. It is being extended in a complex pattern of short neovolcanic zones and oblique transform faults. In its western sector, relatively mature back-arc spreading has created predominantly basaltic segments with characteristics and mineralization generally similar to those of mid- ocean ridges. At its far east, however, the basin is distinctly immature. The East Manus Volcanic Zone lies between two members of the Manus transform set, and is an en-echelon series of neovolcanic edifices constructed on extensionally thinned island arc crust formed during the earlier manus subduction episode. Individual edifices range from predominantly basaltic to predominantly dacitic in composition. Two of the edifices are known to be hydrothermally active, and a particulate plume with unknown source occurs in the seawater column above a third.

Jan 1, 1993

By Kira Mizell, James R. Hein

Ferromanganese (FeMn) crusts form by precipitation of iron and manganese oxides from seawater onto a rock substrate and are therefore considered hydrogenetic in origin. Diagenesis does occur however, through the process of phosphatization. During phosphatization, abundant dissolved phosphate in seawater replaces carbonate in the detrital fraction as well as directly precipitates within the FeMn matrix as carbonate fluorapatite (CFA). This process is likely accompanied by the partial dissolution or replacement of the oxide phases [1]. As a result of these diagenetic processes, trace elements adsorbed on the oxides are released and can either be depleted or enriched in the phosphatized FeMn crust layers. Pb, for example, has been shown in sequential leaching experiments to associate with the iron oxyhydroxide (FeOOH) phase in purely hydrogenetic layers, while >95% of Pb in phosphatized crust layers is found in the CFA fraction [2, 3]. However, previous sequential leaching studies analyzed bulk layers of phosphatized crusts and only a few crusts, from the Pacific Ocean. Here we present concentration data for Pb and other trace elements in the CFA fraction leached from thin stratigraphic intervals of the phosphatized portion of FeMn crusts from the Pacific and Atlantic oceans to confirm consistency of trace metal association with CFA both throughout the phosphatized section and in two ocean basins. The Pb and trace element concentration data from this study will also be compared with data from non-phosphatized crusts from the global ocean. We can then determine the effect of phosphatization on the concentration of Pb and other elements of greater economic interest in FeMn crusts, specifically whether there is overall enrichment, depletion, or possibly even phase transfer of each metal in the phosphatized layers.

Jan 1, 2018

By Andrea Koschinsky, Luise Heinrich, Stefan Gößling-Reisemann

"Germany, like several other countries, has entered a contract with the International Seabed Authority (ISA) to explore the prospects of commercial manganese nodule mining in the Clarion-Clipperton Zone (CCZ). Ensuring a maximally sustainable deep-sea mining operation requires a thorough understanding of the environmental impacts associated with every step of the mining process from the extraction of the nodules at the seafloor to the refinery on land. Against this background, the project presented here applies a combination of scenario-building and life cycle assessment (LCA) to assess and evaluate the sustainability performance of the individual process steps as well as the entire mining operation.Life cycle assessment (LCA) is a comprehensive methodological framework that allows the identification and quantification of impacts occurring during a products life-cycle, as well as the analysis and evaluation of their contribution to pre-defined impact categories, such as climate change, acidification and toxicity (Rebitzer et al., 2004). Until now, LCAs with a focus on raw material extraction have almost exclusively been applied to terrestrial processes. Noteworthy exceptions are offshore drilling, offshore wind farms and ocean fishing. Hence, the first part of the project is to investigate in how far LCA can be applied to deep-sea settings and if and in what way it could be adapted to be used in a deep-sea mining context."

Jan 1, 2017

By Makoto Yuasa, Akira Usui, Shipboard Scientists of SIP Cruises, Atsushi Suzuki, Shingo Kato, Kyoko Yamaoka, Akira Nishimura, Kiyo Kisimoto, Katsuhiko Suzuki

"We report here on current topics of our project, based on the results of recent cruises and laboratory analysis, about the diversity of compositions and configurations of the hydrogenetic ferromanganese deposits in several Northwestern Pacific Seamounts. This recent research has discovered important aspects of these deposits regarding the mode of variation with water depth, topography and substrate geology, possible bacterial mediation, temporal variation with age in mineralogy, and major and minor element chemistry. All cruises and analysis have been supported by the facilities and staff of the Japan Agency of Marine-Earth Science and Technology (JAMSTEC), Japan Oil, Gas, and Metal resources Corporation (JOGMEC), Geological Survey of Japan, and Kochi Core Center (KCC) using a remotely operated vehicle (ROV), a monitored rock drilling system, dredges, and manned-submersibles in the NW Pacific seamounts,The results indicate that most of the rock outcrops on the slopes, shoulders, and much of flat tops are covered with maximum 10-cm thick crusts, but the thickness, metal content, and microstructural properties are not always uniform over the seamounts, but variable in space and time. The micro-stratigraphic description of whole-rock samples indicates a history of deposition and sedimentation, which control the diversity in bulk composition and abundance caused by the variable incorporation of iron-manganese precipitates into the deposits during variable environmental conditions. We conclude that hydrogenetic precipitation of iron-manganese oxide has taken place for more than 20 million years at a growth rate about 4-6 mm/my, in water depths below 1000m. The results indicate a fairly continuous and constant metal deposition since the middle Miocene age or older to the present. Our case study of geological sciences at a model seamount within the Japanese EEZ suggests that scientific knowledge is useful and essential in exploring mineral deposits, economic estimation, and designing systems, if supported by well-combined geological and oceanographic and biological research. The distribution map of ferromanganese deposits and geological map will be published soon in 2017 to be issued by the Geological Survey of Japan."

Jan 1, 2017

In the western Woodlark Basin, propagation of seafloor spreading is occurring directly into the continental crust of Papua new Guinea. The spreading is not strictly in a back-arc tectonic setting, rather it appears associated with microplate rotations related to the complex convergence of the Indo-Australian and Pacific plates in the southeastern Pacific region. Volcanic rocks along the western Woodlark spreading axis range from normal mid- ocean ridge basalts to basaltic andesites with back-arc geochemical affinities. Rare peralkaline rhyolites also occur. Hydrothermal deposits occur at a basaltic andesite volcano located on the neovolcanic zone near its westernmost propagating tip. Franklin Seamount is a 250m-high cone constructed largely of pillow lavas and talus which sits astride a 450m-high ridge of similar lavas oriented subnormal to the spreading direction. At its crest, 2150m below sea level, there is a 100m-deep caldera.

Jan 1, 1993

By Eric J. Foell

Recognizing that the planned commercial exploitation of polymetallic nodules in the deep sea should be accompanied by environmental studies in order to protect this largest and least understood ecosystem of our planet, the German Ministry for Research and Technology has since 1989 funded a longterm and large-scale disturbance-recolonization (DISCOL) experiment in the abyssal Peru Basin of the equatorial South Pacific Ocean. The circular study site is located at 4150m depths and encompasses about 10km2 of relatively flat, heavily sedimented sea floor with low (< 15%) nodule coverage near an existing German nodule mining exploration license area. The RV SONNE, a large and well-equipped multi-purpose research vessel, served as platform for all environmental cruises conducted to date. The initial DISCOL expedition (SO-61, Feb.-March 1989) was carried out in two legs. During DISCOL 1/1, a study site was selected, a pre-disturbance baseline assessment was undertaken, and sea floor disruption was begun using the "plow-harrow", a uniquely designed disturber device towed repeatedly across the circular study area. During DISCOL 1/2, disturber deployments continued until the device had created 78 criss-crossing and partially overlapping tracks along which nodules were essentially plowed under while sediment from up to 15cm below the seabed had been turned over and exposed at the surface. In addition to the obvious within disturber track impacts, sediment mobilized by plowing drifted off with the prevailing near-bottom current and redeposited downstream, blanketing nearby areas not directly disturbed. Immediately after the disturbance phase, an initial post-impact sampling series was performed. The DISCOL Experimental Area (DEA) was revisited about six months (DISCOL 2, SO-64, Sept. 1989), three years (DISCOL 3, SO-77, Feb. 1992), and seven years (ATESEPP SO-106, Jan.-March 1996) after disturbance to collect further post-impact samples, monitor changes in the benthic community and follow the recolonization process. In addition to benthic community studies, plankton investigations were initiated during the third DISCOL cruise (SO-77) and continued during three further cruises (SO-78, SO-79 and SO-80/2) in 1992.

Jan 1, 1996

By Guillaume Blanc

The development of marine mining in the offshore areas adjacent to most of the insular and continental European States is limited by the complex and evolving nature of its legal regime on the basis of the relevant applicable international, European and domestic rules. As the development of marine mining requires investments in capital-intensive technologies, the bankable feasibility of marine mining projects is very much dependent on the legal security of mining rights, assets and operations in offshore areas. This is quite difficult to assess due to the constant accumulation of applicable and potentially conflicting international and domestic laws in these areas, in particular the coastal zone, the territorial sea, and the Exclusive Economic Zone (EEZ). The often conflicting interaction of international treaties, laws and regulations in offshore areas raises specific and major issues in terms of permitting processes, access rights, ownership rights over the mineral resources explored and mined, flag vs. coastal State jurisdiction over mining vessels and marine mining equipment, international environmental liabilities, and unitisation and multi-forum disputes. In addition, the determination of jurisdiction and the legal regime under which marine mining could take place is becoming even more complex with the development of EU Law and the recent revision of the International Law of the Sea, particularly the new extension regime of the EEZ and jurisdiction over the continental shelf.

Jan 1, 2004

By Tobias Hens, Andrew Frierdich, Barbara Etschmann, Joël Brugger, Barrie Bolton

"Ferromanganese (Fe-Mn) nodules and crusts are prime targets for future deep-sea mining ventures due to their unusual enrichment of critical metals, such as Ni, Co, Cu, Ti, Te, Zr, Hf, Nb, Y, and REE. These metals are used in an ever increasing variety of high- and green-tech applications such as alloys, batteries for hybrid cars, fiber-optic cables, or liquid-crystal displays.1 Recovery and processing of these deposits will most likely be cost-intensive and require new solutions.2 Thus, innovative approaches towards the development of sustainable metallurgical processes represent one component that can positively affect the marine mining value chain. Dynamic mineral recrystallization of Fe- Mn oxide phases is a geochemical process that may have notable potential for future hydrometallurgical applications.Our research focuses on Mn oxides – potent trace metal scavengers with high sorptive capacity3 – and biogeochemical mechanisms that control Fe-Mn nodule and crust formation, alteration, and trace element enrichment. Biogeochemical redox cycling of Mn is characterized by microbial oxidation of aqueous Mn(II) to Mn(III,IV) oxides and (a)biotic reduction of these oxides to Mn(II)aq. During this cycling dissolved Mn(II) is in direct contact with solid-phase Mn(III,IV) oxides and can back-react via abiotic pathways (e.g., 4 and references therein). This results in continuous dynamic recrystallization of the Mn mineral substrate through coupled dissolution (trace metal release) – reprecipitation (trace metal incorporation) processes.4 We recently demonstrated in new experiments, that Ni is cycled during manganite recrystallization. It has been shown that, although Ni readily undergoes mineral-fluid repartitioning in the absence of Mn(II)aq, dissolved Mn(II) significantly catalyzes Ni exchange between solid phase and solution. Over a period of 50 days about 30 percent of the Ni atoms in Ni-substituted manganite (natural abundance composition) were exchanged with a 62Ni(II)aq isotope tracer at pH 7.5. Based on these outcomes we employed similar techniques to investigate the impact of dynamic recrystallization on Mn oxide phases in deep-sea ferromanganese nodules and crusts from three circum-Australian locations (South Tasman Rise, Lord Howe Rise, Coral Sea) and the Central Pacific Basin."

Jan 1, 2017

By Maria Thornhill, Rolf Arne Kleiv

INTRODUCTION The last decade has given rise to an increasing number of deep-sea mining concepts (DSMCs) outlining technical solutions for the production chain from seafloor mining to mineral or metal extraction. The vast technological and logistical challenges coupled with immature but rapidly evolving technology has spawned a great variety in proposed concepts, and the exact implications of the phrase ‘best available technology’ is very much an open question. DSMCs differ significantly with respect to choice of technology, technological readiness level, degree of resource utilization, logistics, OPEX and CAPEX requirements, overall profitability, legal and political implications, not to mention environmental impact. Hence, a system for classifying concepts could provide a useful identification and structuring tool when performing economic, judicial or environmental assessments of DSMCs, as well as offering a general terminology to describe concepts sharing fundamental traits. This abstract proposes a DSMC classification system based on how a concept makes use of mineral separation at the different stages in the ore’s journey from the deposit to the ocean surface and ultimately to onshore facilities. Mineral separation, as a process step, is the key factor in determining both the state and mass flow of materials along the production chain and has, as such, a decisive effect on economy and environmental impact of any deep-sea mining project. A DSMC that is based on bringing the entire volume of broken ore to onshore facilities for processing will look very different from a concept based on pre-concentration (i.e. mineral separation) at the seafloor. Whereas the latter offers savings in the form of reduced energy cost for vertical transport, it also represents a substantial additional technological challenge. Furthermore, whether or not a concept relies on mineral processing at the seafloor or on a floating facility at the ocean surface above the deposit also determines the point at which mineral separation waste (i.e. tailings) must be managed. Different concepts offer different opportunities for tailings deposition, and are at the same time bound by different requirements.

Jan 1, 2018

By Lorena Blanco, Guillermo Gómez-Ramos, Iker Blasco, Egidio Marino, Luis Somoza, Ricardo León, Teresa Medialdea, Javier González

"This study presents the first catalogue of marine mineral deposits and energy resources along the continental margin of Spain. Aggregates, oil and gas and metalliferous mineral areas have been defined and mapped. The catalogue, implemented in a geographic information system (GIS), is conceived as a first national database within the European network, which is being built as part of the EMODnet-Geology project. It comprises 8 types of mineral and energy resources for the Spanish margins: aggregates, hydrocarbons, evaporites, placer deposits, phosphorites, polymetallic sulfides, polymetallic nodules and cobalt-rich ferromanganese crusts (Figures 1 and 2). The catalogue stores a total of 409 marine mineral deposits and compiles information such as name, deposit type, main morphology, main minerals, setting or area extent for each mineral deposit. By number of deposits compiled, the aggregates are the most abundant (286) followed by hydrocarbons (62), cobalt-rich ferromanganese crusts (32), evaporites (9), placer deposits (8), phosphorites (5), polymetallic nodules (4) and polymetallic sulphide deposits (3). Considering the total extension, hydrocarbons (32,386 km2) and cobalt-rich ferromanganese crusts (24,951 km2) represent the biggest areas.The Geological Survey of Spain (IGME) is developing a new tool in the catalogue, according the International Seabed Authority (ISA) Database parameters, for individual samples on each ferromanganese deposit. The database includes an extensive collection of records that comprise five information groups: general cruise and sample data, physical properties, mineralogy, geochemistry and acronyms used. New attributes have been incorporated, in example: geophysical, sedimentological and petrological data in the deposit area, sample weight, porosity, morphology, textural and structural features, geochemistry of major, minor and trace elements (included REEs and PGEs) and supplementary cruise and laboratory reports. This new database complements the EMODnet-Geology project minerals catalogue, offering a deeper level of information for the areas with major potential for mineral or energy resources as they are the Canary Island Seamount Province, the West Margin of Galicia and the Gulf of Cadiz."

Jan 1, 2017

By Peter E. Halbach

The Central Indian Ridge (CIR), the boundary between the African and Indian plates, forms a SSE trending mid-oceanic accretionary system in the equatorial Indian Ocean (Fig. 1), extending to the northerly Carlsberg Ridge spreading center, and terminating at the Rodrigues Triple Junction (RTJ; 25°30&apos;S, 70°06&apos;E) by intersection with the Southwest Indian Ridge (SWIR) and the Southeast Indian Ridge (SEIR). Crustal divergence of the CIR proceeds at intermediate rates; a progressive increase of ocean floor accretion towards the south is documented: the present half spreading rate and ridge trend change from 1.80 cm/a and N142° at the equator to 2.73 cm/a and N152° north of the triple point. The topography of the central rift zone is rather smooth compared to slow spreading analogues such as the SWIR, but slightly more rugged than the SEIR. The rift valley is 500-800 m deep, 10-15 km wide and usually well defined. The inner floor, 2-4 km in width, is relatively flat along the axis and more variable in cross section, and lies at 2700-3200 m depth. Off set fracture zones striking generally N60° . in southern portions of the CIR and laterally displacing median valleys by as much as 8 km are often bent, uplifting crustal sequences up to several hundred meters. The length of individual spreading segments varies between a few and several tens of kilometers. The vertical displacement on normal faults are larger while lineaments are shorter than those of the faster spreading SEIR. The direction of lineaments measured on the southwestern and northeastern flanks of the southern CIR are N154° and

Jan 1, 1994

By Ning Yang, Sup Hong

INTRODUCTION Metal components contained in deep-seabed mineral resources are being highlighted as “energy metals”, which are widely utilized in the entire fields of energy: harvesting and generation, storage and transportation, and saving. Those are mostly trace and rare metals, and rare earth elements as well: manganese, nickel, cobalt, copper, molybdenum, tellurium, selenium, platinum, etc. Toward low carbon society, for global sustainability, the role of metals and minerals is growing up in industries of energy and transportation [1]. In this context, the production and supply of energy metals from deep seafloor have to be approached also based on sustainable development. In deep-seabed mining activity, the sustainability is focused on potential impacts on ecosystems in benthic area and water column. The environmental impacts in deep-seabed mining are caused basically by intervention in benthic zones and transportation of materials. Those are, in particular, removal of benthic habitats, generation and dispersion of sediment plumes, surface transportation of seawater and sediment, tailing from mining vessel, sound and light noises, and chemical leakage, etc. This paper is aiming at fundamental guidance towards sustainable mining of polymetallic nodules.

Jan 1, 2018

By C. R. Pearce, B. Murton, S. Howarth, P. Lusty

"With the expansion of “green” energy technologies, the demand for the critical raw materials required to sustain this growth is increasing. Many E-tech elements, including tellurium (Te) and rare earth elements (REEs), suffer from high supply shortage risk and the need for more diversified metal supply routes is driving research into alternative resources. Hydrogenetic ferromanganese crusts, seafloor deposits of Fe- and Mnoxyhydroxides that form from the direct precipitation from seawater, present a potentially important future source of E-tech elements. With growing interest in the potential wealth of these deposits and the issuing of permits for deep-sea mining and exploration, more work is underway to understand the nature of ferromanganese crust deposits, their elemental concentrations and distributions, and the potential impacts of mining activities.This research focusses on the formation of ferromanganese crust deposits and processes that control the extreme enrichment of elements such as Te, Co and REEs. The crusts were systematically sampled and mapped between ~ 1000 – 4000 m depths using ROV ISIS, from a range of environments, substrates and morphologies from Tropic Seamount (NE Atlantic) in order to determine the seamount-scale factors that control major and trace elemental concentration variations. These factors include depth, surface roughness and micro-bathymetry, location relative to long-term mean current direction and energy, influence of tidal energy dispersion across the seamount, sediment supply, substrate lithology, biological productivity and phosphatisation. The study analyses trace-element characteristics of 100 ferromanganese crust samples alongside standard reference materials NOD-A-1 and NOD-P-1 (US Geological Survey manganese nodules). At this initial stage, we report results from whole rock acid digestion and ICP-MS analyses."

Jan 1, 2017

By M. Ye. Melnikov

The report is about oceanic ferromanganese crusts ? covers of iron and manganese hydroxides developed over an opened rock of seamounts and rises. Ore bed parameters of crusts are understandable as their thickness and content of main economic components ? manganese, cobalt and nickel. All known results of research activity on ferromanganese manganese crusts point to that crust are characterized by notable variability of thicknesses and composition. It is possible to separate few levels of variability. The most evident is the first level of parameters variability, which is manifested in various regions of the Ocean, and connected first of all, with an age of submarine mountains, a host objects for a crusts. It was proved by many authors, that most powerful crusts are connected with submarine mountains of Cretaceous age. [1]. Crust thickness at the Magellan Seamounts reaches, for example 12-15 cm, sometimes exceeds 20-22 cm. Thicknesses of Hawaii Archipelago or Tuamotu crusts in 3-4 times less. Biostratigraphy studies of crustal sections at the Magellan Seamounts already show, that its main part started to form in the Late Paleocene. Four layers with well expressed features in structure and composition of a layer are separated in the section. From foot to top: Late Paleocene ? Early Eocene layer I-1, Middle-Late-Eocene layer I-2, Miocene layer II and Pliocene ? Quaternary layer III. Relics of more ancient Campanian ? Maastrichtian ore layer [2, 4] were discovered. It is evident for example, that Oligocene mountains could not be a host for two lower layers in the crust section.

Jan 1, 2010

By J. W. Jamieson

"The future of the marine mining industry is tied to the resource potential of the seafloor. Everything from economic feasibility, policy decisions and environmental impact assessments to extraction techniques and mining tool design rely on an understanding of the size, composition, and distribution of the deposits. Development and regulatory decisions must ultimately be tied to not only the grade and tonnage estimates of individual deposits or groups of deposits, but also an understanding of the uncertainty of these estimates. Here, we will discuss how seafloor massive sulfide (SMS) deposit grades and tonnages are evaluated, and the sources of the uncertainties associated with these values.TONNAGE UNCERTAINTYFirst-order tonnage (size) estimates for SMS deposits are primarily determined from calculating the volumes of material that occurs as positive bathymetric features on the seafloor. The extent of sulfide mineralization on the seafloor can be determined either from visual surveys (camera-tow, remotely-operated vehicle (ROV), or human-occupied submersible surveys) or from volume calculations of bathymetric features identified from digital elevation models of the seafloor, or a combination of both methods. For bathymetric models to be used to identify deposits in the absence of visual groundtruthing, data resolution of 1 m or less is generally required to confidently identify a feature as being hydrothermal in origin (as opposed to a volcanic or tectonic feature), and therefore near-bottom multibeam data acquisition (e.g., using autonomous underwater vehicle (AUVs) or remotely operated vehicles (ROVs) is required (Fig. 1). Specific characteristics of bathymetric features, such as shape, slope angles and surface roughness can be used to identify features of hydrothermal origin (Fig. 1). However, so far, bathymetric features mapped at a resolution of ~1 m cannot be relied upon to unambiguously distinguish a sulfide mound, and the additional use of multiple AUVmounted sensors, such as magnetometers, which can be used to detect hydrothermal upflow zones, or self-potential sensors, which detect electrical fields related to the oxidation of sulfide minerals, can increase the confidence that a bathymetric feature is indeed a sulfide body, without the need for expensive and time-consuming visual surveys (c.f. Petersen et al., this volume)."

Jan 1, 2017

By Charles W. Finkl

Coastal and marine aggregate (sand and gravel) mining on US continental shelves is a major activity that supplies industrial and commercial demands for these raw materials. Because Pacific, Atlantic, and Gulf coasts contain significant shoreline segments that are in a critical state of erosion, sand-gravel and mixed sediment (sands with a high percentage of silt-plus-clay) deposits are mined in efforts to mitigate land loss. Sandy shores, and to a limited extent gravel coasts, erode by shoreline retreat due to relative sea-level rise and sediment starvation in littoral drift patterns. Mostly gravel shores occur in high latitudes and shorelines often advance seaward due to isostatic rebound following the LGM (Last Glacial Maximum 18,000 YBP). Sandy and fine-grained shores occurring in middle and low latitudes of the conterminous United States are problem coasts that require beach renourishment and reconstruction of barrier islands. Muddy coasts of the Mississippi Delta region are especially problematic because some islands are literally disappearing in response to subsidence. Replacement of sediments lost to the littoral drift system or returned to sedimentary sinks by drowning is thus a critical endeavor that involves annually dredging hundreds of millions of cubic meters of sediments from the continental shelf area. The types of shelf sediments that are amenable to marine mining techniques, their occurrence, and means of detection are highlighted in this paper. Minable Sediments on the Continental Shelf Wide varieties of sedimentary bodies that occur on the continental shelf are amenable to mining for beach renourishment and barrier island (beach-dune-marsh system) reconstruction. Relict terrestrial deposits make up a small but important proportion of shelf sediments that were deposited on coastal plains, now drowned by the post-glacial sea-level rise to form continental shelves. Examples of these deposits include drowned moraines, outwash plains, eskers, and kettles along the northern Atlantic coast in addition to siliciclastics along middle latitude Pacific, Atlantic, and Gulf coasts. Special cases include carbonate sequences along tropical costs of Florida and the muddy coasts of deltas, mostly in Louisiana. Specific types of minable deposits thus include shoreface attached sand sheets, dunes, and ridges in addition to offshore inter-reefal sands (between coral reefs in the Florida Reef Tract), bank deposits, and sand waves (ridges) that extend into US territorial waters. Nearshore siliciclastics include ebb-tidal deltas and bars. Drowned river valleys occur along all three US coasts and can be exploited for their fluvial sands if the covering mud sheets are thin.

Jan 1, 2005

By Peter E. Halbach, Andreas Jahn

Co-rich hydrogenetic ferromanganese crusts are typical marine interface products of growth processes taking place on sediment-free substrate rocks on the seafloor. They grow very slowly and preferentially in water depths below the oxygen-minimum zone (OMZ) and have so far been found even in water depths of up to more than 5000 m, i.e. also below the calcite compensation depth (CCD); these deep ferromanganese crusts are particularly rich in Fe. It is assumed that the O2-minimum zone is the most important source layer of dissolved manganese, the decomposition of fecal pellets here also contributes to this Mn-budget. The process of hydrogenetic precipitation is basically an inorganic colloidal-chemical as well as a surface-chemical mechanism. Microbial mediations can be assumed, in particular since steps of redox-reactions are involved. The two main components of the hydrogenetic substance are hydrated d-MnO2 (vernadite) and x-ray amorphous Fe-oxyhydroxide, both of which are intimately intergrown with each other forming the extremely fine-grained hydrous oxidic material. In seawater, elements occur as dissolved hydrated ions or as inorganic as well as organic complexes which, in general, have either a positive or a negative surface charge depending on the pH of the respective marine environment. These complexes form hydrated colloids that interact with each other or with other dissolved hydrous metal ions. The main agent to oxidize the dissolved Mn2+ ions is oxygen, transported upwards from deeper water by turbulent eddy diffusion and turbulent rise processes at seamount slopes.

Jan 1, 2017

By Raymond A. Binns

In this first sub-seafloor examination of an active hydrothermal system hosted by felsic volcanic rocks at a convergent plate margin, we drilled 13 holes altogether, achieving deep cored penetrations at two sites. Our aims were (1) to delineate the lateral and vertical variability in mineralisation and alteration patterns below the PACMANUS hydrothermal site near the 1650-1700 m-deep crest of Pual Ridge in the eastern Manus back-arc basin, so as to understand links between volcanological, structural and hydrothermal phenomena, and (2) to establish the nature and extent of microbial activity within the system. Technological innovations vital to success included our precise location of holes on small targets with drill-stem video, the use of a new hard-rock re-entry strategy, and deployment of casing with a new hammer drill. Other technical achievements were the first ODP application of an advanced diamond coring system, and the first direct comparison in a hardrock environment between structural images obtained by wireline methods and by logging-while-drilling (resistivity-at-bit).

Jan 1, 2002