Search Documents

By Z. Y. Lan

Bioleaching of marmatite with various mixed cultures of microorganisms was investigated. The experiments were carried out in shaking flasks with iron-free nutrient and the pulp density of 10% wt/vol at the temperature of 30?. The results show that zinc is preferentially leached before iron. The leaching rate of zinc with the mixed culture of Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans and Leptospirillum ferrooxidans is 62% in 18 days. The leaching rate of zinc with the mixed culture of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans is nearly the same as that with the mixed culture of Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans (45% versus 50%). SEM and EDX analysis of the leaching residues indicate that a solid product layer composed of iron sulfide, elemental sulfur and jarosite accumulates in the mineral surface and becomes a barrier to the dissolution of marmatite. The bioleaching of marmatite follows the shrinking core product layer model. When the product layer increases and becomes insoluble, the leaching rate is controlled by the diffusion through the product layer and slows down. When the product layer decreases or becomes a porous layer, the leaching rate is controlled by chemical reaction and enhanced dramatically.

Jan 1, 2014

By W. Kobal

The extraction of nickel (Ni) and cobalt (Co) from the laterite deposit of Ramu nickel-cobalt Project in Papua New Guinea was performed in this study. Chemical analysis by Inductively Coupled Plasma (ICP-AES) atomic emission spectrometer, SPS-3000 (Seiko Instruments (Inc.), shows the ore contains 48% Fe, 1% Ni, 0.1% Co, 1.8% Al, 0.14% Mg, and 0.8% Mn. Characterization by X-ray diffraction (XRD) analysis of the laterite ore obtained from the mine site shows the ore contains 70 to 80% goethite (FeOOH), assuming Fe content of 48% is mainly from geothite. The main leaching parameters investigated include; slurry temperature, leaching time and sulphuric acid (H2SO4) concentration to evaluate nickel and cobalt extraction. For all experiments, 10g batch samples are put into 300 ml beaker containing 100 ml of sulphuric acid of varying concentrations (1M, 2M, 4M). During the leaching period, 5 ml slurry samples are withdrawn at different times and filtered to obtain filtrate for ICP analysis to monitor nickel and cobalt extraction. Solid samples at the end of all tests are also obtained by filtration and after drying, XRD and ICP tests are performed to monitor nickel and cobalt contents. According to the test results performed at normal atmospheric pressure, over 99% of nickel and over 50% cobalt were extracted into solution within 120 min at 95ºC in 2M H2SO4 solution. Similar results were obtained when only temperature was reduced to 90ºC, but cobalt extraction increased to over 70% when leaching time was increased to 240 min. Further reduction in temperature to 80 and 60ºC resulted in reduction of nickel and cobalt extraction. At the end of each leaching test, magnetite was seen to attach to magnetic stirrer. The study showed nickel can be completely leached into solution but cobalt only up to 70%. Keywords: atmospheric pressure, sulphuric acid leaching, nickel laterite

Sep 1, 2012

By W. Y. Gao

Diaojuntai Concentrator adopts a process of low intensity and high intensity magnetic separation and anionic reverse flotation, with all the concentrate from magnetic separation being treated by re-verse flotation to obtain a qualified final concentrate. The high reagent cost and energy consumption of the reverse flotation have led to a high concentrate cost. The test research on reducing the feed to the reverse flotation was therefore carried out. Based on the study of the properties of the ore sample, the concentrate of low intensity magnetic separation was screened at 0.076 mm and the undersize fraction was concentrated by concentrator with gravity and magnetic field. The results show that a qualified concentrate can be obtained at various rising current rate, pulsating current and power-on style, with the operation rate over 85%. The extraction of some part of qualified concentrate from the concentrate of low intensity magnetic separation by magnetic separation can reduce the feed to the reverse flotation by about 35% so as to reduce the production cost of concentrate.

Jan 1, 2014

By I. Nishkov, I. Grigorova, N. Valkanov, M. Ranchev

The processing of sulphide ores with variable and complex mineral composition and physical properties, such as those processed by two-stage selective flotation scheme in “Erma reka” concentrator, Minstroy Holding JSC, requires excellent selectivity in order to achieve acceptable concentrate grades. The lead-zinc ores from the hydrothermal lead-zinc deposits mainly contain galena (PbS), sphalerite (ZnS), pyrite (FeS) and chalcopyrite (CuFeS2), as well as non-metal minerals such as quartz, carbonates and clinopyroxenes skarns. One of the main impurities present in sphalerite is iron, which is known to be detrimental to the rate of sphalerite flotation and its recovery. The results from the conducted laboratory and industrial tests, presented in the previous study, showed that it is possible to depress the iron rich sphalerite by adding MINFIT® (modified sulfur-oxy depressant) at the pH of approximately 9.5 in rougher lead flotation circuit, leading to reduction of zinc sulphate consumption and complete elimination of cyanides from the flotation process. Furthermore, the consumption of copper sulphate, which reactivates the surface of the zinc minerals, was significantly reduced. Consequently, the optimisation of the reagent regime in the Erma reka concentrator, led to notably improved qualitative (grade, recovery) properties of the final lead and zinc concentrates. Moreover, when comparing the reagents consumption for 2014 and 2016 – when the processing plant have been applying the new optimized reagents regime, comprises the use of MINFIT as the primary depressant, the following results have been achieved: ZnSO4 decreased by 30%; CuSO4 consumption decreased four times and full rejection of cyanides from the process. Finally, this paper provides a state-of-the-art review of the obtained results during the period of application of the new flotation reagents regime in the Erma reka concentrator, Minstroy Holding JSC.

Jan 1, 2018

By E. Yigit

In the flotation process the physical factors such as agitation intensity air flow rate and pulp solid concentration are very important parameters affecting grades and recoveries of the products. The flotation tests were performed on the samples of Bigadic colemanite ore to investigate these factors at different agitation intensities ranging from 1000 rpm to 1400 rpm and air flow rates from 1000 cm3 ? min-1 to 2000 cm3 ? min-1 with 2 L and 4 L cells using Denver laboratory flotation machine. The tested collectors were Cytec Aero 825, Aero 848N and their mixtures. Agitation intensity and air flow rises resulted in more floated material although sometimes being not selective. These effects can be attributed to powerful collisions between air bubbles and mineral particles. The first observation was the effect of pulp solid concentration on the floatability of minerals, while the flotation in 2 L cell (0.125 g.L-1 solid concentration) at 1000 rpm (0.176 wattcm-3), and with 1000 cm3.min-1 air flow rate was possible, the flotation in 4 L cell (0.0625 g.L-1 solid concentration at 1000 rpm. (0.176 wattcm-3) and with 1000 cm3 ? min-1 air flow rate was not possible. However at 4 L cell after increasing agitation intensity to 1200 rpm (0.201 wattcm-3) keeping 1000 cm3 ? min-1 air flow rate, flotation was possible again. This shows that these factors such as agitation intensity have some critical role on flotation. Another interesting observation was on the selective effect of pulp solid concentration. In the flotation with 1 L cell at different agitation intensities, collector Aero 848N was selective against calcite, while in the flotation with 2 L cell at different agitation intensities the same collector Aero 848N was selective against colemanite.

Jan 1, 2014

By E. V. Manlapig, M. C. Harris

"The complexity of the flotation process has made the identification of an appropriate model structure, for use in the prediction of flotation circuit performance, far from obvious. Work performed under the auspices of the AMIRA P9 flotation program has indicated that the metallurgical performance achieved from a flotation cell arises from the interaction of two essentially independent property classes, namely the cell operating conditions and the properties of the cell feed stream. These observations have led to the development of a model structure that associates a constant set of flotation parameters to the streams of the circuit, which are transformed into a flotation response depending on the operating conditions within the flotation cell.A variety of alternative model structures exist within the literature which do not make this distinction between cell and stream flotation properties, and many of these models are in widespread use for flotation optimisation and design studies, both in industry and academia.In this paper, data collected from an industrial flotation circuit is used to derive the parameters associated with two different types of flotation models. Simulations performed using these models demonstrate the need to differentiate between cell and feed properties. A model that does not differentiate between these two properties fails to successfully predict the metallurgical performance of a flotation circuit after a disturbance."

Jan 1, 2003

By T. Wallmach, S. B. Blancher, A. Delaporte, P. Goncalves

"Fe-Ti oxides concentrates produced from heavy mineral sand deposits are widely used for the production of titanium dioxide pigments that are critical components of white paint, plastics and paper. According to mining industry, the Fe-Ti concentrates mostly consists of three phases: ilmenite, leucoxene and rutile. However, a few mineralogical studies have shown that the variety of Fe-Ti oxides found in sand deposits is far more complex, mostly due to alteration processes. The aim of this contribution is to characterize in detail by means of Qemscan analyses the mineralogy of the three main concentrates (ilmenite, leucoxene and rutile) produced by the Grande Côte Operation (GCO) mineralurgical plant in Senegal. The ultimate goal is to characterize the different products and textures formed during the natural ilmenite alteration processes, to localize the phases carrying the main impurities (Cr and P), and finally to determine the physical properties of each mineral component to improve metal recoveries. Along alteration processes, Ti content increase. Ilmenite (FeTiO3) is progressively transformed into pseudorutile (Fe2Ti3O9) particles which could also be altered and transformed into hydroxylian pseudorutile [FeTi6O12(OH)3.3H2O] or complex blends of anatase microcrystals (TiO2). These transformations are accompanied by significant changes in particle textures. Microporosity and fractures appear and the impurity content also increases. Anatase rich microcrystal assemblages, so far described as Leucoxene, could be identified to consist of grains with higher porosities, water contents and higher intrapore impurities. These particles are the main carriers of chromium and phosphorus. The observed mineral transition textures have a significant impact on the ore dressing processes. During these transformations, the physical properties of these phases change, the magnetic susceptibility as well as densities decreases, due to the increase in porosity. The separation of particles, especially those with high porosity will help improving the GCO mineralurgical plant performance and to reduce the impurity contents in finals products."

Jan 1, 2018

By Gu Guohua

The alteration of surface properties of chalcopyrite after biological conditioning with Leptospirillum ferriphilum was studied by adsorption, zeta-potential, contact angle and bioleaching tests. The strains of L. ferriphilum cultured using different energy sources (either soluble ferrous ion or chalcopyrite) were used. The adhesion of bacteria to the chalcopyrite surface was a fast process. Additionally, the adsorption of substrate-grown bacteria was greater and faster than that of liquid-grown ones. The isoelectric point (IEP) of chalcopyrite moved toward that of pure L. ferriphilum after conditioning with bacteria. The chalcopyrite contact angle curves motioned diversely in the 9K culture with and without chalcopyrite powders. The results of X-ray diffraction patterns (XRD), scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) analysis indicated that in the bioleaching process by L. ferriphilum, the surface of chalcopyrite was covered with sulfur and jarosite. Furthermore, iron phase dissolved preferentially from chalcopyrite surface during bioleaching from EDS detection. The copper extraction was low resulting from the formation of a passivation layer. The major component of the passivation layer that blocked continuous copper extraction was sulfur, not jarosite.

Sep 1, 2012

By M. X. Jia

This paper discusses two mineralogy characteristics that may affect the flotation of sulfide ore. The first one, process mineralogy study on a Cu-Ni sulfide ore shows that valleriite and tochilinite are incline to form on chalcopyrite, pyrrhotite and serpentine surface, and the further guess is that the formation of valleriite and tochilinite may also causes the serpentine transform to talc, so the serpentine surface is a phase of talc or a transition phase from serpentine to talc and this enhances the flotability of the gangue minerals. The second discussion on the flotation behavior of the sulfide minerals from the point of view of the mineral semiconductor character.

Jan 1, 2014

By Sepideh Javanshir

The process of liquid?liquid extraction of gold from chloride solution is complicated by the presence of many variables acting simultaneously in an unknown non-linear fashion for the determination of the final extraction efficiency. In practice, it is quite difficult to develop a model for predicting various properties of such process. Therefore, an alternative approach based on Artificial Neural Network (ANN) is considered to assist in the simulation process. Artificial neural networks (ANN) are powerful tools that can be used to model and investigate various highly complex and non-linear phenomena. This paper presents application of Multi-Layer Perceptions (MLP) to construct relationship that will be employed to develop a quantitative method for the estimation of the extraction efficiency as a function of hydrodynamical parameters such as stirrer speed, [AuCl4]- and DBC concentration, organic and aqueous flow rate. The model is shown to be in excellent agreement with the experimental data (R2 value for training and testing data was 0.9992 and 0.9915 respectively). Therefore, it can be used to optimize the parameters of liquid?liquid gold extraction with dibutyl carbitol (DBC).

Sep 1, 2012

By T. Damyanov

Spherical grinding media (balls) are the most widely used media for comminution of ores by grinding. A modelling simulation study of the behavior of two grinding media in the grinding process was conducted to determine the possible advantages of the new shape milling bodies called tetraballpebs. Tetraballpebs are in the shape of tetrahedrons with spherical convex walls. A three dimensional CAD model of the mill drum with a diameter of 1200 mm was used. A continuous operating mode was simulated in terms of the 3D contact elements of the model (milling bodies and mill drum). Simulation tests were carried out in a typical grinding mode and at a typical rotational speed of the drum mill (75 per cent of the critical speed in cataracting mode). Studies carried out with both grinding media include equal number of milling bodies with the same weight and volume. Having thus ensured a uniform mass of the grinding media and same number of milling bodies, and constant other conditions and process parameters, conclusions can be drawn about the influence of the shape of the milling bodies on the grinding process. A kinematic analysis of the system using CAE (computer-aided engineering) model parameterization was conducted. The controlled parameters are: ? Power draw; ? Kinetic energy of each milling body; ? Motion of milling bodies inside the drum Keywords: grinding, grinding simulation, balls, tetraballpebs, DEM, CAD-CAE

Sep 1, 2012

By J. Y. P. Leite

In the Borborema Pegmatitic Province (Brazil) exploitations of several minerals are conducted by small producers. They use traditional techniques of gravity concentration in small-scale plants as jigs and vibratory tables. During decades the mining activity generated tailings with economic interest in particularly columbite-tantalite. Samples collected in tailing piles of a gravity plant were characterized in mineral composition, which shows in the heavy fraction the minerals spodumene, columbite-tantalite, ilmeno-hematite, garnet and cassiterite. The light fraction presents quartz, feldspar and muscovite. The degree of liberation of spodumene and columbite-tantalite were determined using optical microscopy that presents liberation in 100 µm (90% to columbite-tantalite and 100% to spodumene). Centrifugal concentrator Falcon SB-40 was used for concentration of these minerals and presents 65% recovery in mass to two stages with mass reduction about 85%.

Sep 1, 2012

By Z. D. Tan

The continuous digestion technological conditions of phosphate tailings with high magnesium content in sulfuric and phosphoric mixed acid is studied in this paper. The influences of excess coefficient of sulfuric acid, weight liquid to solid, reaction temperature and time on conversion of P2O5 and MgO are discussed. The influence of infiltration capacity of phosphogypsum by the concentration of liquid-phase SO3 is discussed too. Under the optimal technological conditions, the conversion of P2O5 is 95.56% and MgO 98.63%, the filtration rate of phosphogypsum increases with the increasing of liquid-phase concentration of SO3, the optimal apparent concentration of SO3 is 0.135~0.14g? mL-1 in liquid-phase. The filtration rate of phosphogypsum is 1473kg? m-2? h-1. N-P-Mg compound fertilizer was produced by adding magnesia powder and inflating ammonia in filtering medium.

Jan 1, 2014

By Auhin Kumar Maparu

Metal oxide nano-particles are used as additives in various industrial applications such as pigments in paints, additives in adhesives, plastics, cosmetics, functional coatings, personal care and health care products, for antibacterial applications and more recently in heat transfer applications. In most of these applications, usually dry nano-particle powders are added to the formulations. However, often it becomes difficult to achieve a uniform and stable dispersion of nano-particles in the given formulation. Thus, a scalable and commercially viable process for in-situ production of stable nano-particles suspensions in the desired medium will certainly be more beneficial. Ultra-fine grinding in high energy mills (planetary mill, stirred media mill) has been used to produce fine particles (sub-micron size). However, in order to obtain nano-particles (particle size <100 nm), the choice of appropriate dispersant and solvent is crucial, since freshly generated nano-particles tend to agglomerate due to their high surface reactivity. We have employed molecular modeling (MM) based selection methodology to arrive at the most suitable solvent?dispersant combination for preparation of the given metal oxide nano-particles. Molecular modeling techniques are employed to compute the interaction energy of a given dispersant with surface of the metal oxide particles in the presence of the dispersion medium. The interaction energy helps identify a dispersant that has strong affinity for the metal oxide surfaces allowing for strong dispersant adsorption and hence a more stable dispersion. For example, in case of aqueous nano-titania suspensions, poly-carboxylic acids like citric acid provide better dispersion than mono-carboxylic acids like lauric acid, mysristic acid, and oleic acid. While in non-aqueous medium like ethanol, p-hydroxybenzoic acid and glycerol trioleate perform better. The suspension is produced in-situ by ultra-fine grinding of the metal oxide powder in the presence of the selected dispersant and dispersion medium in a planetary ball mill. By careful selection of various process parameters such as percent loading of powder, jar filling, grinding media to powder ratio, time and amount of dispersant addition, both aqueous and non-aqueous suspensions of metal oxide nano-particles with average particle size less than 100 nm are produced. The aqueous suspensions of alumina and titania produced in presence of citric acid dispersant exhibit median particle size of 83 and 62 nm, respectively. These suspensions have been found to be stable for nearly 3 years. The nano-particles thus produced are used in the preparation of nano-fluids?advance heat transfer liquids, which show enhanced heat transfer capabilities and unaltered stability and performance even after several heating-cooling cycles. The nano-particles are also utilized for making efficient photo catalysts, which are found to be highly effective under sunlight. Keywords: stability, nano-fluid, milling, grinding, thermal conductivity, nanocoolant, photocatalyst

Sep 1, 2012

By A. V. Kurkov

The secondary action reagents (SAR) are organic diphilic compounds capable of altering ac-id-base and donor-acceptor properties of the main collector and consequently the energy of collector interaction with the mineral?s surface, its hardness and fixation forms ratio through associates formation via the hydrogen bonds. When the basic flotation conditions are being established, convergence of the electronic structure of the collector and the mineral being extracted due to minerals surface preconditioning with modifiers and the most efficient collector choice. At the next stage of the selective flotation condition establishment SAR is selected for a more precise adjustment of the energy of the collector fixation on the mineral. Such an approach makes it possible to solve efficiently various issues of flotation separation of non-sulfide minerals. In particular neutral organic substances containing groupings C==O, S==O, P==O (ethers of carboxylic and phosphonic acids, amides of carboxylic, phosphonic and sulfonic acids) were proposed as SAR. In order to enhance the flotation process selectivity in the conditions of water recycling including the selectivity of carboxylic collectors especially in the environment of high hardness water flotation, it was proposed to use SAR with long hydrocarbonic radical and groups with enhanced electronic density within the molecule: N-methylolamides of alkylphosphoric acids and ethers of methylphosphonic acid. Introduction of small amounts of these compounds alongside with the main fatty-acid collector enhance the performance of fatty-acid flotation of fluorite, beryl, columbite etc., lowers the collector consumption, and completely compensates the depressive effect of recycled water. Di-2-ethylhexyl ether of methylphosphonic acid?CH3P(O)(OC8H17-i)2 (hexarane) was more thoroughly researched as such an agent within fatty-acid flotation process. Following aspects of the flotation system were studied: interaction of oleic acid and sodium oleate with hexarane in the liquid phase (infrared spectroscopy); heat emission under the interaction of hexarane-oleic acid ? sodium oleate ? calcium salts (isoperiboric diathermic colorimeter); colloid-disperse state of the collector influenced by hexarane (nephelometric analysis); dynamics of the mineral surface hydration due to the agents (method of indicator negative adsorption); hexarane effect upon the interaction of fat-ty-acid collector with calcium salts (complexometric method with Trilon-B); floatability of pure minerals (quartz, microcline, beryl, columbite) in Hallimond tube; hexarane effect upon oleic acid (sodium oleate) adsorption (nephelometric method for identification of the residual content of oleic acid and its forms within the solution). Upon the research it can be definitely concluded that the adjusting effect of such compounds as hexarane within the non-sulfide minerals flotation process is mainly determined by their interaction with the main collector both within the pulp and at the mineral surface with associates formation due to the hydrogen bond. The consequence is calcium oleates destruction with the release of the most active collector under flotation in hard water environment which determines the efficiency of hexarane joint application with fatty-acid collector under recycled water supply. Therefore the introduction of the class of secondary action reagents is supported by their operation mechanisms and flotation process function and determines a new approach to the development of efficient conditions of selective flotation separation of non-sulfide minerals.

Jan 1, 2014

By J. Jirestig

Poor grade iron ore, suffering from interlocked particles, is challenging for any process technology. Extensive grinding is required to attain liberation and to yield concentrates of desired grade. Fine particles are commonly very difficult to retrieve, resulting in value losses to tailings. In this paper, results from HGMS tests on fine to ultra fine hematite are reported. Special emphasis is put on slurry flow velocity. If hydrodynamic drag force, i.e. flow velocity is not controlled and kept constant during the feed and/or rinse phase, fine particles will not be captured and retained. Flow velocity control and constant flow during separation are achieved by discharge valves/slots and parallel magnetic flux and pulp flow configuration. In tests, increased slurry velocity from 178 to 268mm/s caused Fe-recovery to drop from 78 to 48%. Proving that flow velocity control is essential to optimise grade and recovery. HGMS tests at the Metso mineral laboratory on natural (weathered) hematite fines clearly show a large potential to recover valuables, currently lost to tailings. Even at particle size distributions as low as D80=35µm concentrate grades and recovery are very satisfying. Two samples, in-plant desliming rejects (D80=35µm and 50µm) where significantly upgraded and recovered, from 45,3% to 63,6% and 53,0% to 63,4% Fe, at 73,8% and 81,1% Fe-recovery respectively. Other types of in plant rejects, such as gravity separation or WHIMS tailings, also benefits from HGMS separation. Gravity separation reject, 55,8% Fe, at D80=500µm was tested, yielding a magnetic concentrate of 60,8% Fe at 50,7% Fe-recovery. The results indicated that the hematite was poorly liberated. HGMS separation was repeated after a regrind to D80 150µm, resulting in a magnetic concentrate of 62,8% Fe at 75,9% Fe-recovery. The tests prove that hematite, presently lost to tailings streams, can be recovered by HGMS and thereby significantly contribute to improved overall economy. Keywords: HGMS, magnetic separation, recovery of ultra-fine hematite, Indian hematite ores, hematite recovery from tailings

Sep 1, 2012

By A. V. Yevdokimov, Ye. V. Bogorodsky

The paper presents the results of the research on the development of gravity concentrates processing technology (gold grade is from 50 g/t to 1 kg/t and over) using intensive cyanidation with gold recovery to pregnant solutions followed by precipitation of metals from them using various methods. Test work and pilot plant results confirm that a new developed hydrodynamic regime provides an efficient treatment of gravity concentrates of polydisperse composition without their grinding and preliminary desliming. The resulting pregnant and washing solutions are amenable to metals recovery using electrowinning, cementation onto zinc dust and CIS. Cone plants with a lower ball valve for cyanidation of unground gravity concentrates developed by IRGIREDMET JSC have been successfully tested at a number of Russian operations. Currently, a modular plant equipped with gold electric precipitation from pregnant solution unit is successfully operated at a Russian gold processing plant. Cyanidation of the resulting high-grade gravity concentrate is carried out at the concentration of 8-10 g/L NaCN and 10 g/L NaOH. Gold recovery to the solution is 97-98%. Electrowinning is carried out in flow cell GNC-40M. In this case, the residual gold concentration yield is 0.3-0.5 mg/L. Also, a modular plant for relatively low-grade middlings (50-100 g/t Au) of gravity concentration has been introduced. The concentration of NaCN and NaOH is 2-3 g/L and 1.5-2 g/L, respectively, during leaching. This plant is equipped with a unit for gold cementation from pregnant solution with zinc dust. This cementation unit is of original design. It is made in the form of a filtering device and is composed of several layers of carbon fiber which contacts with zinc powder. The residual gold concentration yield from a cementation unit is less than 0.1 mg/L. Gold recovery is 93-97%. In 2017-2018, the introduction of intensive cyanidation modular plants to gravity concentrates will be planned at new projects of Russia and the CIS.

Jan 1, 2018

By V. K. Gupta

Several approaches to the estimation of the size discrete breakage rate and distribution parameters (kj and bi,j ) of the batch grinding kinetic model are available in the literature. Analysis of a large amount of data available in the literature and our own data on several pure minerals and complex ores has shown that it is not always possible to obtain correct estimates of the two sets of parameters using known approaches as several widely different combinations of k and b parameters can sometimes simulate the batch grinding data reasonably accurately. It has been found that there are two main reasons: (i) all size classes are not well represented in the data and (ii) functional forms used for estimation of the two sets of parameters are sometimes chosen somewhat arbitrarily (especially in the case of complex ores), though they are actually uniquely related through size continuous breakage rate and distribution functions. A suitable experimental methodology has been described and demonstrated using some synthetic data and actual experimental data. A mill function approach, which does not require making any assumptions about the functional forms for k and b parameters, is also described and demonstrated. This approach is promising, but requires further development.

Sep 1, 2012

By Jochen Petersen, David G. Dixon

"Although heap leaching may be perceived as a somewhat low-tech route for the extraction of low-grade minerals, the underlying physical, chemical and biological processes are in fact extremely complex. There has been increased interest in heap leaching of sulphide minerals in recent years with the advent of controlled bio-heap leaching, and the need to mine more marginal ore deposits.A detailed investigation into the dynamics of heap leach processes has provided much insight into the underlying complexities, and has led to the development of a sophisticated modelling tool. Some of the features include mineral kinetics, particle level effects, bacterial growth, oxidation and adsorption, gas adsorption, pore diffusion, bulk advection, gas balance and heat conservation.Two case studies are presented which illustrate specific features of the model for different applications and how these have helped to identify key areas of concern. In each case the model has proved as an invaluable tool either for the improvement of existing heap leach practice or for the development and assessment of novel applications."

Jan 1, 2003

By S. Narra

Converting biomass into valuable fuel requires various preprocessing of the raw materials. Biomass densification is one of the conversion processes for its utilization. The aim of densification is to produce biomass pellets, which can withstand regular handling stresses and exhibit high densities with uniform size and shape. Physical properties, such as the particle size distribution after comminution is of highest importance for the binding mechanisms in the pelletisation process. Durability and strength of the pellets play an important role indicating the ability to withstand handling stresses. Particle size distributions of the cereal straws (Rye and Wheat) after specific comminution and liberation processes have been carried out with the help of three different image analysis (Microscope, Camsizer and Fibreshape). The durability of the pellets have been investigated as specified in the standards (ASAE standard S269.4) with a quadratic crate and the strength of the pellets with compression and tension testing machine (Zwick Roell type: ZMART.PRO). The particles size results showed differences in both length and width after different comminution processing. An exact comparison between the particle size analyses with the three different image analyses was not possible. The particle size distribution and the different comminution processes displayed influences on the durability and strength of the produced pellets. The particle size distribution displayed approximately 40 % of fines and 60 % of fibers. The particle size distribution displayed a direct relation to the durability of the pellets. Further durability and strength of the pellets displayed a good correlation.

Sep 1, 2012