Search Documents

By Q. X. Li

The state discharge standard for arsenic-containing wastewater which is the first kind of pollution is less than 0.5 mg/L. In fact, in a certain company, the acidic arsenic-containing wastewater in non-ferrous smelting was as high as 860 mg/L, which is far beyond the state discharge standard. Obviously, the direct release of this wastewater without further treatment would result in great hazards to the ecological environment. To aim directly at the characteristics of acidic arsenic-containing wastewater, in this study, two steps of treatment including oxidation-flocculation and removal fluoride by mixing alkaline neutralization were suggested. Through analyzing various influencing factors in treatment effects, the optimum technical conditions were obtained. The sediments after treating were recyclable and the secondary pollutions can be avoided. Moreover, the results also show that, all indexes of the effluent after treating are lower than the First Grade Standard of Integrated Wastewater Discharge (GB 8978-1996). This novel method has advantages of short flow sheet, easy operation and low cost.

Jan 1, 2014

By G. W. Zhang

Ultra-fine Stirred Mill is a kind of high energy efficient equipment for ultra-fine grinding, and has been the mainstream equipment in the submicron powder and slurry industry. This paper mainly describes flow-field numerical simulation of the three popular ultra-fine grinding mills: (respective-ly as) Disc Stirred Mill, Pin Stirred Mill and Spiral Stirred Mill, by means of the software Computational Fluid Dynamics (CFD). In the flow-field numerical simulation, the velocity gradient, shear rate dispersion of the flow-field, the viscosity dissipation rate were analyzed with CFD. It is discovered that Pin Stirred Mill has the highest velocity gradient in circular directions and the most homogeneous distribution of shear rate among the three. Flow-field numerical simulation provides a new way (and means to) for the parameter optimization design and project enlargement of Ultra-fine Stirred Mill. The experiments were also carried out, the results are consistent with the results of the simulation analysis. For example, in GCC grinding experiments under the same conditions, the specific energy consumption of Pin Stirred Mill with 3600L in volume is 15%~17% less, and its processing capability is 13%~15% better than Disc Stirred Mill. Now with its optimized structure and excellent performances, more than ten sets Pin Stirred Mill with 3600L in volume have been used in industrial production in Shandong, Guangdong and Hunan province.

Jan 1, 2014

Vanadium-titanium magnetite from Panzhihua was crushed with open and closed circuit process by high pressure grinding roller (HPGR). The particle size characteristics of the crushed product were analyzed and the micro-cracks generated by HPGR during the crushing process were studied. The results showed that, in crushed products, the reduction ratio increases and the size distribution becomes more uniform with increasing of the pressure on roller?s surfaces. The fine fraction content of crushing products from -3.2 mm classification closed-circuit by HPGR increases obviously compared with that by Jaw Crusher and particle size distribution is more uniform. Large amount of intra-crystalline cracks and cleavage cracks are generated in vanadium-titanium magnetite crushed by HPGR, which makes the specific surface area larger and Bond grinding work index (objective particle size is 0.074 mm) decreased by 14.05% than that by Jaw Crusher. And the liberation degree of monomer of the product crushed by HPGR increased compared with that by Jaw Crusher with the similar fineness of grinding. Keywords: iron ore, high pressure grinding roller, micro-crack

Sep 1, 2012

By A. Shibayama

Soil contamination by organic compounds is one of the most concerned issues on polluted soil. It is well known that there are limited methods to remediate the contaminated soil on site. Especially, the in-situ method for contaminated soil is too difficult to de-contaminate the organic pollutant. In this study, the fundamental ability of soil remediation, which aimed to decrease oil concentration in, in-situ process, have been researched by using a high pressure gas generated from ?crush composition? on artificially oil contaminated soil. The n-hexadecane (n-C16H34) and other organic compounds were selected as soil oil contaminators, gravimetric analysis by soxhlet extraction and GC-MS were used as qualitative and quantitative analysing methods. For the experimental examination, the influences on the difference in the concentration of n-hexadecane (and other organics), the tamping amount, position and repetition of crush composition in soil, and scale (size) of experimental model were investigated. The n-hexadecane concentration reduced by the explosive effect of crush composition showed a reasonable decrease of about 30 wt%~60 wt% compared to the initial n-hexadecane. The removed amount of n-hexadecane and distance from explosion point of the crush composition was related in scale and model of contaminated soil.

Jan 1, 2014

By J. Y. Xu

A mutant of Phanerochaete chrysosporium, which is capable of degrading lignin, was bred by ul-traviolet ray irradiation and this mutant strain shows high capability of degrading of lignite. The degradation ratio of original Yima lignite and nitric acid treated Yima lignite by this mutant are 37.6% and 51.62%respectively, whereas those by the original strain are 31.84% and 32.55% respectively. XRD and FTIR analyses of the lignite converted product show that its polymerization degree and average molecular weight are both greatly reduced. The content of the functional groups is also been altered.

Jan 1, 2014

By M. L. Liu

This work reports the results about the determination of mean activity coefficients and relative partial molar free energies for copper sulfide mineral bioleaching solutions by potentiometric method at 25ºC. The experimental potentiometric data were obtained by combining a solid state membrane-cupric ion selective electrode (Cu2+ ISE), containing a KNO3 filling solution, and an Ag/AgCl electrode. The measurements were performed in different series of copper sulfide mineral bioleaching solutions. The non-ideal behavior of the system was described on the base of the Pitzer ion-interaction model for mixed salts. Meanwhile, the relative partial molar free energies of bioleaching solution were investigated. The determination of the thermodynamic properties offers a basic data for the study of copper sulfide mineral bioleaching solutions.

Jan 1, 2014

By S. J. Ma

To look into the ionic release laws of the sulphide tailings in some copper mine, the effects of the soaking period, temperature, oscillating speed, and pH of the solution on the heavy metals ionic re-lease were investigated through static soaking leaching experiments. The results show that Cu2+, Zn2+, Pb2+, Cr3+ are of different leaching behaviors with soaking period. The ionic concentration in soaking solution for four ions has a great gap. Zn2+ is more easily released out of sulfide tailings than Cu2+, Pb2+, Cr3+ , and the ion release concentrations are not proportion to their contents in the tailings. The time for each ion to reach its maximum concentration are different. The minimum concentration do not occur at the first day. Each ion concentration shows different fluctuation characteristic during soaking process. Solution pH, oscillating speed, and temperature affect the releases of Cu2+, Zn2+, Pb2+, Cr3+ out of the tailings to different extent. The effect of pH value on ion re-lease for the four ions ranks as Zn2+>Cu2+>Pb2+>Cr3+, the oscillating speed ranks as Pb2+>Zn2+>Cu2+>Cr3+, and the temperature ranks as Cr3+>Pb2+>Zn2+>Cu2+.

Jan 1, 2014

By J. Leite

In a small-scale mining in Brazil?s northeast, scheelite were exploited since 1940?s using a traditional gravity concentration flowchart (composed by jigs and shacking tables) that operates with low efficient for fine particles. Tailing of this plant was submitted to chemical, mineralogical and size characterization. Results pointed 50% smaller than 74µm with a grade of 0.11% WO3. The particle?s size is an important operational variable to heighten recuperation by shacking tables. Tests using Falcon SB40 centrifuge concentrators and shacking table were realized, optimizing their operational variables. Based on the tests results a new flowchart was proposed for concentrating and tailings recovery.

Sep 1, 2012

The energy dispersion X-ray fluorescence (EDXRF) analysis technique is a rapid and accurate method for describing sample?s element component and percentage composition. On the base of profound research for the national and international development and research condition, the author researched the EDXRF analyze technique and the EDXRF analyzer?s principle in depth, the difficulties and the key points for research and development of EDXRF analyzer; gave a scheme for re-search of bench EDXRF analyzer; researched some algorithms used in energy spectrum analysis; developed the energy spectrum analysis software based on the Visual C++ 6.0; together with the energy spectrum analysis software, the author designed and processed the structural of the bench XRF analyzer and integrated the import X-ray tube, thermoelectrically cooled Si-PIN photodiode X-ray detector and pulse amplitude analyzer as a model machine. The result shows: The model machine can be used in multi-element analysis at the same time for different types of dry mineral samples, with fast analysis speed, accurate model and high stability.

Jan 1, 2014

By Gökçe Törenli, Okay Tutar

"Predicting the performance of plant-scale comminution circuits is essential to monitor the energy use and product size distribution, allowing us to control and optimize the whole process. In the light of this issue, with the assist of recent technologies, simulation techniques utilize the chance of putting the theory into practice in the most accurate way. For this purpose, this study aims to evaluate and optimize the efficiency of a plant-scale ball mill circuit by using perfect-mixing ball mill model on a simulation environment. The comminution circuit is selected from a specific copper-ore processing plant in Turkey. The essential parameters which are required for this study such as fresh feed Bond work index, size distribution etc. are determined by laboratory experiments. The forecasted data which are calculated by third-party software will be compared by the industrial operating data, in order to determine the performance of comminution circuit. In addition to that, this methodology provides a greater ability to analyse, optimize and understand the comminution circuit of ore treatment plant. The authors believe this work will provide supplementary data for further studies on simulation and subsequent optimization of comminution circuits.INTRODUCTION By the assist of mathematical models of the grinding mills and classifiers, simulation of the grinding circuits become more common in comminution because it is relatively economical and able to consider many variables simultaneously. It’s proceeds depends on the accuracy of the models and capability of reflect real operations. Computer-based simulation studies would provide the quantified information about the effects of the proposed changes on the comminution circuit performance in terms of size distribution, mass flow rates, equipment efficiency etc. Then the mentioned data used in order to check the suitability of the current equipment to the modified conditions, and for equipment selection. The outputs of circuit could also be used to estimate downstream flotation circuit performance because the general aim in this study is to The aim of the study is to investigate optimum operating variables and achieve p(80) size of 57 µm and 64 % of -36 µm particle in hydrocyclone overflow stream, which is optimum for that porphyritic copper ore for best concentrate recovery after flotation process in specific copper ore comminution circuit by using modelling and simulation techniques. Sampling survey was carried on the fine ore bin in order to perform Bond work index test and determine work index value (Wi). Thereafter mass balancing, using the size distribution data and tonnages, models for ball mills and hydrocyclone were developed. Finally, the circuit performance were investigated by computer simulations via JKSimMet software."

Jan 1, 2018

Pyrite and Chalcocite have different crystal lattice, with different dissolution rate in the same ac-id solution, the dissolution rate of which is accelerated with increasing redox potential, they are leached simultaneously at high redox. In present work, some methods are adopted to inhibition the bioleaching of the pyrite by controlling the redox potential. Shake flask experiment shows that the dissolution of pyrite and chalcocite is slow as redox potential <700mV(Eh), but the dissolution in-creases exponentially as redox potential>800mV(Eh), they have good selectivity at redox potential between 700mV and 760mV(Eh).

Jan 1, 2014

By S. M. Wen

In mineral processing, the settling of mineral particles in water, the flow of ore pulp, the dewatering and filtering of concentrates and so on, are related to the pulp viscosity. While the interaction between mineral particle surface and water affects directly the pulp viscosity. Therefore, it is of great value to the development of mineral processing theory to research the effect of mineral particle surface on the water viscosity in boundary layer. In micro-fluid, the effect of mineral particle surface on the water molecules in boundary layer can not be ignored. The water viscosity in boundary layer and the effect of the nature of mineral particle solid surface on the viscosity are analysed based on the deduction of attraction potential energy formula of mineral particle surface to the water molecules in boundary layer. The results show that the attraction potential energy of mineral particle surface to the water molecules in boundary layer is determined by the properties of solid molecules and fluid molecules and varies inversely as the third power of the distance from mineral particle surface. The water viscosity in boundary layer consists of the viscosity of free water and the additional viscosity resulting from the attraction of mineral particle surface. The increment of the viscosity caused by the attraction of mineral surface is µs. This additional viscosity is also inverse ratio to the third power of the distance from mineral particle surface. The greater the dipole moment, the polarizability and the ionization energy of mineral particle solid surface molecules are, the higher the attraction potential energy of mineral particle surface to the water molecules and the water viscosity in boundary layer are. The thicker stationary water boundary layer is d0. The higher the µs is, in other words, the greater the attraction of solid surface to water molecules is, the thicker the stationary water boundary layer becomes when free water viscosity is constant.

Jan 1, 2014

By Wenqing Qin, Yunfan Wang, Ximei Luo, Fen Jiao

In order to investigate the effect of nanobubbles on adsorption of surfactant on mineral surface, the nanobubbles on the surface of calcite with -37µm fraction in the sodium oleate system were controlled by pressurization and decompression to mixing vessel. Subsequently, the adsorption amount of sodium oleate on the surface of calcite were detected by ultraviolet spectrum at different stirring times and different pressures. At the same time, the nanobubbles on the calcite surface were imaged with atomic force microscopy (AFM). In addition, a homemade vacuum Hallimond tube device was used for the flotation of single mineral, and the grade and recovery of minerals in concentrate was used to determine the influence of the nanobubbles on flotation. The experimental results showed that a large number of nanobubbles were found on the calcite surface by AFM under the dissolved oxygen difference (DOD) condition of -4 mg/L. And a large difference in adsorption capacity of sodium oleate on the surface of calcite was observed under different air pressure conditions. It indicated that the ambient pressure had a certain effect on the adsorption of sodium oleate on the calcite surface, and this effect did not depend on the constant low pressure or constant normal pressure, but depended on the changing process of pressure. The single mineral flotation experiment results indicated the recovery of calcite under decompression condition (formation condition of nanobubbles) was 1.5-2 times that under constant normal pressure, and the flotation time is much shorter. Moreover, the recovery under constant normal pressure was greatly influenced by flotation time. In this paper, only one aspect of the effect of nanobubbles on mineral flotation was preliminarily explored. It was confirmed that after vacuum-pumping, the adsorption of sodium oleate on calcite surface could be increased, the flotation time also was greatly reduced and the recovery of calcite was increased.

Jan 1, 2018

By M. E. Ramírez

In this research bioleaching or extraction of iron present in a kaolin from La Virgen mine, Anti-oquia/Colombia, was carried out. Organic acids produced in SF with Aspergillus niger were used in the process. The fermentation process was carried out in 3 L aerobic stirred bioreactors, at a temperature of 30 °C, a stirrerd speed of 700 rpm, an initial pH of 4 and a fermentation time variable between one to 8 days, obtaining broth fermentation samples daily per bioreactor. For iron extraction, fermented broth from second to sixth day of fermentation was evaluated and it was found that the fermentation broth of the third day showed a larger potential for iron removal, 786 ppm, by using kaolin with an initial iron content of 1401 ppm. A set of tests using commercial organics acids such as citric acid and oxalic were carried out because those were found in the fermentation broth and it was found that oxalic acid presented three times more iron removal than citric acid.

Jan 1, 2014

In this study, selective flocculating of diaspore using anion macromolecular reagent as flocculant was tested to separate diaspore from alum-silicate minerals. Firstly, the effect of pH on settling behavior of diaspore and kaolinite dispersions has been investigated. The results show that the maximum settling speed of diaspore and kaolinite appeared re-spectively at pH7 and pH3.33 which is close to the point of zero charge (PZC) of diaspore (6.8) and kaolinite(3.5). This result is in well agreement with the double electric layer theory. Secondly, the settling behavior of diaspore and kaolinite particles in different anion flocculant solution have been researched. The results indicate that flocculant solution concentration significantly affect the selectivity and the flocculating performance of anion molecular. In high concentration solution, both diaspore and kaolinite have faster settling rate compared to blank solution. How-ever, in low concentration solution, the anion macromolecular can enhance the settling rate of diaspore remarkably but has no apparent effect on the settling rate of kaolinite. This result suggests that the tested anion flocculant is a promising reagent for de-silica of diasporic bauxite. Lastly, FTIR method was employed to probe the adsorption mechanism of flocculant on diaspore and kaolinite. The results reveal that there are anion flocculant characteristic bands on the spectra of diaspore but no obvious characteristic bands of flocculant on the FTIR spectrum of kaolinite. This result is in good correspondence with settling test.

Jan 1, 2014

By Boris Albijanic, Hongjuan Chen, Bogale Tadesse

"During mechanical flotation of fine liberation sized complex rare earth ores, a large fraction of ultrafine valuable mineral particles are lost to tailings. Fine gangue mineral particles can be entrapped within the froth phase and be floated together with target mineral particles. Another common challenge in ultrafine rare earth mineral flotation is the formation of a sticky froth (excessively stable froth). Thus, the improvement of the flotation of fine and ultrafine rare earth bearing minerals through appropriate cell design and reagent selection is highly desirable. The aim of this study is to investigate the performance of a pico-bubble cavitation flotation column in improving selective recovery of ultrafine rare-earth elements (REEs) bearing minerals from complex and low-grade ores. In pico-bubble cavitation column, very small bubbles are generated which are capable of attaching to ultrafine particles and consequently modifying their surface properties. The overall effect of these processes should lead to improved flotation selectivity and recovery of ultrafine RE mineral particles. In this paper, the effects of a number of flotation operating variables on recovery and grade of REE minerals was investigated using a continuous pilot scale pico-bubble column flotation. At the flotation conditions used in this study, subtle monazite upgrade was observed while gangue Fe oxide was preferentially floated even in the presence of depressants. INTRODUCTION Rare earth elements (REEs) have unique properties such as superconductivity and catalytic activity, and are in high demand for a large number of cutting-edge technologies in the modern world including the production of mobile phones, fuel cells, displays, permanent magnets for wind power generation, high-capacity batteries, green energy devices, etc (Naumov, 2008). REEs tend to be intimately associated within many minerals, and are rarely found in high concentrations in deposits for economic extraction. Up to now, among over 250 minerals containing REEs, bastnasite (Ce), monazite (Ce, Th and La) and xenotime (Y) are the three main minerals that contain sufficient grade of REEs for commercial exploitation (Zhang and Edwards, 2012). The deposits that contain bastnäsite, monazite and xenotime usually have complicated mineral compositions, with various valuable minerals of fine embedded grain sizes in association with complex gangue minerals. In order to ensure liberation of the REEs minerals, fine grinding to less than 30 µm is necessary. This fine grinding leads to difficulty in recovering a large proportion of fine and ultrafine particles in separation processes such as flotation (Trahar and Warren, 1976). Consequently, highly liberated and ultrafine fine valuable REEs particles are lost into tailings during traditional mechanical flotation. Besides, the formation of extremely sticky and stable froth inhibits the drainage of hydrophobic particles. Thus, improving flotation of rare earth bearing minerals, particularly the ultrafine size range, is highly desirable."

Jan 1, 2018

By H. M. Yang

Structural alteration of pyrophyllite during mechanical activation in a planetary mill was investigated by X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR) techniques. Mechanochemical effect markedly promotes the decrease in reflection intensities with increasing the grinding time. Prolonged grinding causes the pyrophyllite to become the amorphous structure. It can be indicated that pyrophyllite is very susceptible to alteration by grinding. Crystal size (d006) of pyrophyllite appears to be a limit after 2h grinding. IR spectroscopy analysis shows a little alteration in the bands of pyrophyllite after mechanical activation. The results indicate that the ordered structure of pyrophyllite is destroyed and lattice deformation occurs. Porous silica was then successfully prepared via leaching the mechanically activated pyrophyllite. Pyrophyllite was first ground for 6 h. Ground samples were subsequently leached with 4 M hy-drochloric acid at 80 °C for 2 h to produce porous silica with specific surface area of 188.1 m2/g, total pore volume of 0.18 mL/g and average pore size of 3.9 nm from N2 adsorption analysis. Otherwise, the porous silica obtained from direct leaching of the original pyrophyllite only has a specific surface area of 4.3 m adsorption analysis. 2/g and total pore volume of 0.03 mL/g. It is inferred that grinding is favorable for the formation of microstructure pores. It offers a simple and convenient route for the preparation of porous materials from natural minerals.

Jan 1, 2014

By Al Cropp, Julie Hunt, Will Goodall, Ron Berry, Dee Bradshaw

Geometallurgy aids the understanding of ore body variability but has the most value if the data is easily available along the entire mining value chain. This requires cross-discipline communication and collaboration across traditional silos, and an organizational culture that encourages that to flourish. Data that are collected by the numerous groups (i.e. mining, geology, milling, processing, refining, smelting, marketing, environmental etc.) involved in the mining process may have relevance to other stakeholders; mineralogical and textural data for example has value to all these groups. Data required for modeling comminution or identifying acid potential from waste rock may already exist, however it needs to be made available to all the relevant stakeholders in the right format at the right time. As part of the GeM (AMIRA P843 & P843A) project the opportunity has been taken during the sponsor meetings, short courses, case studies etc. to ask the question: ‚What information do you want from further up the chain?? For example, to metallurgists ‚What information would you like from the geology group before the ore enters the mill?? The geology group may already have information important to mineral processing but not know it is of interest. This could, for example, be in the form of a geometallurgical drill core log that contains quantitative measured values. This paper focuses on the interaction between the mining, geology, mineral processing and environmental groups, using ore properties resulting from geological alteration to identify potential impacts throughout the mining process and discusses how a cross discipline approach can benefit all.

Jan 1, 2014

By Dingwu Feng, Jannie S. J. van Deventer

"The effect of ultrasonication on reactions at solid/liquid interfaces was investigated by using an ultrasonic probe in two slurry systems, i.e. cyanidation of a refractory sulphide ore and geopolymerisation of metakaolinite. The surfactant dithiophosphate was used to render the gold bearing sulphide particles hydrophobic, in an attempt to induce the formation of cavitation bubbles directly at the desired surfaces. Oxygen was injected into the cyanidation system to improve the attachment of oxygen bubbles to the hydrophobic sulphide surfaces. Geopolymerisation occurs in highly alkaline solution with waste aluminosilicate oxides and silicates as the reactants. The process of geopolymerisation is believed to involve dissolution of Al-Si oxides from solid particles, diffusion of dissolved Al-Si complex from the solid surface into the gel phase, condensation of gel phase and hardening of the gel phase. It has never been investigated how ultrasonication affects the above steps in synthesising geopolymers, despite a number of papers dealing with sonochemical synthesis of materials. The introduction of power ultrasound into such slurry systems is expected to result in advanced geopolymer materials.In the cyanidation of the pyrite concentrate, the kinetics of gold extraction were significantly enhanced in the presence of ultrasound, due to the prevention of passivation and the enhanced dissolution of sulphides. Cyanide consumption was significantly reduced with ultrasonication, owing to the oxidation of soluble sulphides to sulphate, minimising the cyanide consumption by sulphides. With oxygen injection, ultrasound significantly enhanced the leaching of gold from the pyrite concentrate, as oxygen could enhance the formation of the oxidation radicals by ultrasonic cavitation. In the presence of dithiophosphate, ultrasound further improved gold leaching in the oxygen-aerated system. Dithiophosphate could selectively adsorb at gold host sulphide surfaces, and make the surfaces hydrophobic. As a result, the ultrasonication effectiveness could be enhanced through forming cavitation bubbles directly at the interfaces."

Jan 1, 2003

By Arun Appadurai

Pneumatic transport systems play a vital role in conveying discrete particles over a sizable distance with minimal energy consumption. However if such a system is not designed keeping particle physics in mind, it leads to intractable problems which could possibly assume dangerous proportions, including but not limited to expensive redesign of the entire system. This paper describes a novel method, which harnesses the powerful technique of Computational Fluid Dynamics (CFD) to investigate a problem occurring in rotary kilns using coal as a major fuel source. In some of the sites, a unique phenomenon of abnormally high CO emission was observed and owing to the highly random nature of occurrence, it was difficult to scientifically investigate the problem and its cause. Most of the published solutions for the high CO problem tend to concentrate on the incomplete combustion aspect of the kiln and resolve the situation by increasing the air supply thereby improving the stoichiometric ratio of combustion. This paper offers an alternate correlation that relates high CO emissions to the phenomenon of coal delivery fluctuations caused by the sub-standard operation of the coal transport system. A CFD model for the coal delivery pipe is validated by utilizing the actual process data sourced from the measurements taken from a functioning plant. The results of the model are used to derive correlative conditions that point to the unstable operating conditions of the coal delivery pipe prevalent in the industry. The conclusions are summarized into a series of recommendations for optimized design of coal delivery systems which are implemented in a pilot plant. The results irrevocably prove a statistically significant reduction in CO emissions without resorting to increased air supply and power consumption. Keywords:CFD, Pneumatic Conveying, Saltation Velocity, Particle Flow

Sep 1, 2012