Search Documents

By D. C. Yates, G. V. Jolliffe

In the five coalfields of Staffordshire, there have been some 43 incidents of spontaneous fires and heatings which have required special attention in the past ten years. This total excludes incidents in the Thick Coal Seam of South Staffordshire, which was worked until 1967, and which was subject to an almost continuous series of heatings. The incidents have been classified to show the sites of occurrence, the contributory factors which may have caused them and the treatments applied to them. The remedial techniques, as practised in Staffordshire, are dealt with in detail, with particular reference to standard methods of stopping-off. Precautionary measures taken are described, including a "liability to spontaneous combustion" classification of all seams, and the setting up of an emergency organization with emergency stocks of materials and equipment. The paper is concluded by a few words on the organization and control at the time of an incident.

May 23, 1905

The paper, presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, presents experimental work undertaken to observe the quenching effect of different substances, to find the most efficient of these substances, and to arrive at a possible explanation of their preventive action. The coal-dusts experimented with were such as passed through a 100-mesh sieve (10,000 holes to the square inch), and were obtained by grinding the coals. The quenching substances, used in as fine a state of division as possible, included gypsum, dried Chance mud, quicklime, magnesia, magnesia alba (levis), anhydrous sodium carbonate, sodium bicarbonate, soda-crystals, Glauber salts, ground shale and boiler-ashes

Dec 1, 1916

By E. C. I. Hammerbeck

"Geological controls and constraints in space and time define the milieu of the nickel deposits of Southern Africa. Primary, magmatic deposits are of two types, e.g. synvolcanic or syntectonic deposits confined to certain orogenic domains, and those related to intracratonic, post-orogenic magmatism, e.g. the Great Dyke, the Bushveld Complex and the Insizwa intrusion. Epigenetic and supergene deposits form a separate, unrelated group and are of minor economic importance.The metallogenic evolution of syntectonic nickel deposits is particularly well illustrated in the Zimbabwean Province, where the relationships between Archaean greenstone development and nickel mineralization are best illustrated. Volumetrically subordinate, nickel-poor greenstones in the 3500 m.y. old Sebakwian Group are followed by more common komatiite development in the Lower Greenstones (3000 m.y.), and, finally, by very significant komatiites with important nickel mineralization in the 2700 m.y. old Upper Greenstones of the Bulawayan Group. Comparable nickel mineralization is not known in the Raapvaal Province, in spite of ubiquitous komatiitic magmatism of the Onverwacht Group (3500 m.y.) and other greenstone sequences. No komatiitic rocks younger than about 3200 m.y. are known in this region, orogenic activity in the Kaapvaal tectonic province having ceased at about 3100 m.y., whereas the Zimbabwe Province remained tectonically active until at least 2600 m.y.The tectonic environment, host-rock petrology and mode of emplacement, as well as some details of the nickel mineralization, are the parameters employed to classify the Southern African magmatic nickel deposits. A rating of the deposits is introduced that reflects the original resources of the deposit, its average nickel content, its mining history and potential to facilitate ready comparison with and assessment of the nickel deposits listed in the classification, as well as some important nickel deposits worldwide."

Jan 1, 1984

By Winmill T. F.

Paper presented at the at the Institution of Mining Engineers' general meeting held in London on 8th June 1916: In a previous paper it has been shown that the rate of absorption of oxygen by coal is neither directly proportional to the surface area of the coal exposed nor to the percentage of oxygen in the air. Further experiments are now described supporting this conclusion

Dec 1, 1916

By V. E. Ross

A comparison was made of three methods for determining the contributions of true flotation and entrainment during batch flotation tests. In the first method size-by-size recoveries are measured in both the presence and the absence of a collector, a frother being present in both tests. In the second method the mass of solids and water recovered after a chosen time of flotation is varied by changing the rate of froth removal and the depth of the froth. The third method uses a transfer factor to describe the classification of solids and water, and hence the changes in the composition of the pulp, during a single flotation test. Batch flotation tests were carried out with artificial mixtures of pyrite and gangue, the amount of floated material recovered being calculated according to each of the three methods. The discrepancies betweeen the calculated amounts are analysed in terms of the assumptions that are made for the various methods and the most suitable conditions for the application of each method are identified

Dec 1, 1991

By Z Hu

The technique of reclaiming disturbed land by use of a hydraulic dredge pump (HDP) (which is a set of hydraulic machines for earthwork), termed 'digging deep to fill shallow has been used in the reclamation of subsidence areas in Chinese coal mines. This paper discusses the operational principle of the technique and summarises its reclamation procedures, which are being used in current reclamation practice. The soil condition reclaimed by the HDP was studied. The results showed that the pioneer crops to be planted in the reclaimed soil should be the ‘pulse’ family crops, and that improvements to the reclaimed soil and the HDP technique itself are needed. Bused on the analysis of the previous technical processes, a new rational technical model for the HDP reclamation method is presented in this paper.

Jan 4, 1996

By R. W. Ruddle

The advent of new methods of roasting, “flash roasting and fluidisation”, which are now under development, combined with the use of oxygen-enriched air, may markedly increase the SO2 content of roaster smokes. Skogmo suggests that the production of smokes containing as much as 50 per cent SO2 should be feasible. The use of flash smelting processes may well enable a similar increase in the SO2 content of smelter smokes to be made. In this event the recovery of sulphur would be greatly cheapened and the process might well be much more economic, even if allowance is made for the cost of generating the oxygen

Jan 1, 1953

By L. Wade, R. Wang, M. A. Horton

Laboratory methods to find the mechanical properties of rock are inherently biased towards stronger strata, which best survive the sample preparation process. Geophysical techniques are not subject to such bias and may be used to predict mechanical properties rapidly and cheaply. Samples (151) were obtained from a borehole that had been comprehensively geophysically logged. The mechanical properties of the samples were established in the laboratory and correlated with the geophysical responses of the strata from which they came. The results indicate that, for homogeneous strata at least, it is possible to predict the unconfined compressive strength reasonably well from sonic travel time measurements made in the field. Predictions of static Young's modulus may also be made from this data source, but with a lesser degree of confidence. A multivariate regression equation is presented which relates down-hole sonic travel time to unconfined compressive strength, depth and the frequency of fractures in the rock mass. This equation may offer potential for the prediction of the mechanical rock properties of fractured and layered strata.

Jan 4, 1993

By J. P. Ress

In 1903, seventeen years after mining of the Witwatersrand gold-bearing reefs started, the findings erf the Miners' Phthisis Commission (Transvaal) resulted in the initiation of measures with the object of controlling dust production. The substance of these measures was as follows: Removal of persons from places where they would be exposed to blasting fumes; use of water to suppress dust made in drilling and in other operations; supply and control of air to working-places; filtration of dusty air; and determination of the amount of the dust in the air. Broadly speaking, progress in dust control has followed these four lines with increasing success as the nature of the problem has become better known. Complete success has not, however, been achieved, partly because increasing mechanization of mining has intensified the problem and partly because the application of these measures is not infallible, being subject, in many cases, to human control. A brief summary of the development of these measures will lead to a description of present-day practice.

Jan 1, 1947

By Williams J. A.

"Changes proposed in 1969 to modernize legislation governing the exploitation of mineral deposits in the United Kingdom serve as the basis for a discussion of what is considered to be a desirable framework for future legislative proposals.Proposals with regard to prospecting and exploration, evaluation, and acquisition and exploitation are considered, as are suggestions relating, inter alia, to aerial surveys and land restoration.It is concluded that without legislation along the lines proposed there can be no significant revival of metal mining in Britain."

Dec 30, 1971

By R. Trueman, D. B. Tyler

Numerical modelling was used to determine the magnitude and direction of stresses around drives both adjacent to and distant from open stopes in the South Crofty tin mine. Modelling predicted that drives near the stopes are situated in a stress-relaxed zone. The peripheries of drives that are sited in solid rock away from the influence of stoping are in compression. Key-block modelling was used to determine the typical geometries of critical blocks and distinct element modelling was used to determine block stability. The conclusions derived from modelling fitted the observational data. This indicated that key-block theory is a valid tool for analysing the stability of roadways in the South Crofty mine. The support requirements for drives located next to stoped-out areas were formulated using a risk analysis approach to key-block formation. The results were compared with support guidelines derived using empirical design methods. Good agreement was obtained for the roofs of the drives but not for the sidewalls. The concept of a critical excavation width was formulated: once an excavation is larger than the critical size the length of rockbolts need not be increased as the excavtion dimensions increase. This may be the case in all rock mases.

Jan 4, 1993

By A. G. Waters, N. J. Bristow

A comparative study was made of an untreated and a heated haematite ore and a sinter produced from a feed consisting of 100% ore, to study the influence on reduction behaviour of sinter bonding phases such as SFCA (silico-ferrite of calcium and alumina). Under low-temperature reduction conditions the order of increasing reducibility followed that of increasing porosity and surface area but under similar conditions at 900 degrees C the sinter exhibited higher reducibility than the ores even though the total porosity and chemical reducibility of the individual phases were lower. This behaviour can be explained in terms of the higher total porosity of the natural ore at low temperatures and the higher level of fine pores in the sinter at high temperatures due to the presence of SFCA, which acts to support the fine (c.0.1 micrometre) pores created by the reduction process. This leads to the conclusion that the main role of SFCA in sinter during high-temperature reduction is to maintain a high level of fine porosity. Some implications of this work for granule design and sintering practice are discussed

Apr 1, 1991

By H. L. Shergold, O. Mellgren

The conditions of amine concentration and pH necessary for the concentration of fine haematite particles at the iso-octane-water interface have been determined. Results obtained from the related studies on the effect of pH and dodecylamine concentration on the adsorption density, electrokinetic potential, contact angle and concentration of various amine species in the system are included. A good correlation was obtained between these different variables. Maximum concentration of haematite at the oil-water interface was obtained when the haematite zeta-potential was small or equal to zero

Dec 1, 1971

By R. N. Pryor, S. H. Shaw, D. L. Dowie, S. H. U. Bowie, M. J. Cahalan, S. F. Gandar

It is concluded that land-based mineral resources will be adequate for most minerals in the immediate future, but in the long term more minerals will come from offshore locations. Because the oceans are international and can transport pollution, international control of offshore workings will be necessary. In the UK and similarly highly developed areas, the working of low-value bulk minerals will create increasing problems in urban development and countryside preservation. Much more information should be published on standards to be adopted and their costs, if emotional social pressures founded on ignorance are to be avoided. The Town and Country Planning Acts have greatly improved the environmental quality in Britain in relation to mineral working. In the long term conservation of some minerals in short supply may be necessary on a national or international basis. Much research is required for the determination of adequate criteria and standards for the preservation of environmental quality in the mineral industry. New local, national and international legislation will be required and the adoption of voluntary standards by trade associations should be encouraged wherever appropriate

Dec 1, 1971

By A. H. G. Mitchell

Gold-poor and gold-rich porphyry and epithermal gold-silver deposits of Caenozoic and Cretaceous age in the western Pacific and central and eastern Europe are confined to predominantly andesitic continental margins and island arcs. The arc volcanic rocks overlie a complex non-oceanic basement of stacked nappes, the uppermost of which is often ophiolitic. The emplacement of ophiolite triggered a reversal of tectonic polarity, subduction and arc magmatism. Andesitic volcanism and the formation of a strato-volcano were followed by the ascent of magma and porphyry copper mineralisation. Regional propylitic alteration came from convecting, predominantly meteoric fluids. Magmatic degassing caused advanced argillic alteration. This is commonly unmineralised in perched water tables, but may sometimes host high sulphidation gold or enargite gold at deeper levels within the propylitic zone. The onset of extensional stress after the andesitic volcanism allowed meteoric water to circulate to depths of 5 km or more, with consequent cooling of an ascending magma body at depth and the development of low sulphidation epithermal gold mineralisation near and immediately above the sub-volcanic basement surface. All andesitic arcs are mineralised. Regional controls on their ore potential include the level of erosion and geological features in the basement that focus the ascent of fluids. Differences between the mineralisation of the European and the western Pacific arcs may reflect the presence of older, more granitic basements in many of the European arcs.

Jan 12, 1992

By I. R. Hanby

A simple but comprehensive method has been developed for the simulation of a mechanical-drive dump truck that enables various parameters to be predicted as a function of time throughout its whole cycle. Uses of the simulation results are indicated with specific attention to environmental and operational or economic planning. The output of a sample run is presented. The method can be easily adapted for the investigation of a wide variety of mobile plants.

Jan 4, 1992

By C. C. Harris

The two best known graphical methods for presenting and comparing comminution data are obtained by linearising the Gates-Gaudin-Schuhmann and the Rosin-Rammler size distribution equations. It is shown that the Gates-Gaudin-Schuhmann equation can cause excessive congestion in the 50 per cent oversize range and that, overall, the Rosin-Rammler is a better procedure. Examples are given

Dec 1, 1971

By Winmill T. F.

(Paper presented at the Institution of Mining Engineers' general meeting held in London on 8th June 1916.) The conclusions reached in this paper may be summarized briefly as follows: (1) The method of estimating moisture in coal by determining the loss in weight of a sample heated to 105°-110° Cent, in an air-bath for an hour is untrustworthy, the results so obtained being too low. (2) Dried coal has a very considerable power of absorbing moisture, and a sample, after being dried, must be protected instantly if it is to remain free from moisture. (3) A fairly accurate estimation may be made by heating the coal in a current of dry air at 105° to 110° Cent., and collecting the moisture evolved. (4) In cases in which it is proposed to use the dried coal for any further experiments, the drying must be done in the absence of oxygen, and this can be done simply and quickly by the vacuum method now described

Dec 1, 1916

By F. Reich, S. L. Chryssoulis, K. G. Stowe

The surface chemistry of particulates from mineral processing streams can be determined by laser-probe microanalysis. The small area of analysis (2-30 micrometres) enables the surfaces of individual grains to be characterised. Conclusions are based on data acquired from a statistically significant number of grains of a given type. Maps showing the distribution of elements on the surface of mineral particulates can be obtained by time-of-flight secondary ion mass spectrometry. The importance of such analyses in understanding the response of minerals to beneficiation practices is discussed with reference to three examples. The first relates to the loss of selectivity in the differential flotation of a base-metal ore, the second to the different flotabilities of coarse- and fine-grained pentlandite from a Cu-Ni ore and the third concerns the preg-robbing effects of organic matter in a carbonaceous gold ore.

Jan 4, 1992

By D. J. Esdale, D. F. Pridmore, F. W. Lindman, J. H. Coggon

Almost all the presently viable nickel reserves in the Yilgarn Block contain nickel in a sulphide phase. Both volcanic peridotite- associated (VPA) deposits and intrusive dunite-associated (IDA) deposits are characterized by massive, matrix and disseminated sulphides (typically, pyrrhotite, pentlandite, pyrite, chalcopyrite, magnetite and other spinels), though in the IDA deposits the volume of disseminated sulphides is far greater than that in the VPA deposits. Potentially all geophysical techniques have application in the direct detection of these deposits'gravity for the detection of the dense massive and matrix ore; magnetics for the detection of magnetite and pyrrhotite in the ores; electromagnetics for the detection of the massive and matrix ore; and induced polarization for the detection of disseminated and to some extent matrix and massive ore. In practice the application of geophysical techniques is limited to a varying extent by (1) the relatively small size of an economic accumulation of sulphides, particularly the VPA deposits, (2) the extreme depth of weathering and lack of outcrop on the Yilgarn Block and (3) the abundance of geological noise or anomalous responses caused by sources other than economic mineralization.

Jan 1, 1984